Staging: rtl8192e: fix lots of sparse warnings

This removes a number of static and extern warnings that sparse
complains about.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: add Realtek 8192 PCI wireless driver

This wireless driver should work for the Realtek 8192 PCI devices.

It comes directly from Realtek and has been tested to work on at least
one laptop in the wild.

Cc: Anthony Wong <awong1@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: pohmelfs: sync with the development tree

* cache coherency protocol fix
 * proper timeout handling
 * implement dump/del all config group command
  (Signed-off-by: Pierpaolo Giacomin <yrz@anche.no>)

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: remove flush_workqueue()

mac80211 already does flush_workqueue() at stop/start and
suspend\resume.
(fix build error)

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: comedi: apci3200: fix test of ui_DelayTime range in i_APCI3200_CommandTestAnalogInput()

For ui_DelayTime to be less than 1 and greater than 1023 is logically
impossible.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rspiusb: Check usb_buffer_map_sg() retval

usb_buffer_map_sg() may return -1, check this directly.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: panel: Add support for TI CLCD interface

On TI DA850/OMAP-L138 EVM, HD44780 (24x2) LCD panel is being
used[1], but it is interfaced through the SoC specific LCD
interface and not through parallel port. A parallel port
driver has been developed which interfaces to the panel driver
through the SoC specific LCD interface.

Basically, both the serial and parallel interfaces supported
by the panel driver do not suit the specific interface SoC is
supporting so, a new interface type has been introduced.

Ideally the panel driver should be de-coupled from parallel
and serial port related items but this patch is something
that can be merged in the meantime.

[1]Specification of the character LCD interface on TI DA850/OMAP-L138:
http://www.ti.com/litv/pdf/sprufm0a.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill off the TXDMA CSR type

Go to a u32 and masks

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill off the TXDMA error type

This isn't actually used properly anyway

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: re-order the initpci code to match usual Linux style

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: prune all the debug code

We don't need it, we have a perfectly good set of debug tools. For this pass
keep a few debug printks around which are "should not happen" items

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill the loopback type

Kill off the loopback type in the driver

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill MSI type

Kill off the MSI structure

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: put the jagcore routines in with their users

We have two trivial IRQ routines, a single statement and a real function -
relocate them. While we are at it kill the trivial to sort out soft reset
and slv bits in the same areas of code.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill the interrupt magic define and types

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: clean up MP_FLAG macros

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: clean up DMA10/DMA4 types

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: clean up PM_CSR_t

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill the Q_ADDR struct

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: quick tidy of the debug code

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: clean up MMC_SRAM_

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: sort out the mmc enable routine

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: eeprom remove features

We only read eeprom id 0, in byte mode - so the rest can go away

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: remove unused PCI identifiers

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: continue pruning unused fields

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: de-hungarianise a bit

bOverrideAddress is write only so kill it rather than fix it

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: fold the diet config into the other code

No point having a file just for that

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: config is already zeroed

Adapter was cleared by netdev allocation so any zero defaults do not need
writing.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: attack the config stuff

Prune this back as most of it isn't relevant or used

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: clean up constant rx/tx registry fields

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: eliminate write only registry fields

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: Eliminate RegistryDMA Cache

One writer, of a constant, one user .. it can go.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: CSRAddress to regs

Switch this to a Linux like naming as it occurs all over.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: Take a kref for the PCI pointer we cache

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill copied PCI fields

They are all in the pcidev anyway plus are not used by the code

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: MPSend macros

Most are unused, one is used and can be replaced with the definition

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging et131x: kill refcount

The RefCount field is accessed only by a macro and the only use of it in
the tree is to read it, so it can go

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: kill unused RCV_REF macros

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: power state

This is assigned once to ndis d0, and then never changes so it is a constant
and we can zap it

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: spinlocks

Switch to the more normal "flags" naming. Also fix up the nested use of
spin_lock_irqsave

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et1310: kill pAdapter in favour of a sane name

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: pohmelfs: fix type errors

Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: pohmelfs: fix atomic type spew

atomic_long != atomic

Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: altpciechdma: 64bit type warning fix

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: iio: fix duplicate dev_attr_name

device attr's should be static, otherwise duplicate identifiers are
created:

drivers/staging/iio/trigger/iio-trig-gpio.o:(.data+0x1c): multiple definition of `dev_attr_name'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: iio: Fix type warnings

Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: Add todo list for staging

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: Initial documentation

This needs considerably more work, all comments / suggestions
welcomed.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: Proof of concept gpio trigger

Simple example of how a gpio trigger driver would work.
Things to be added include interupt type control (high, low).

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: Periodic timer based trigger

The original posting of this driver led to a discussion in
which it was commented that a better system was needed
for dealing with the many possible periodic interrupt
sources available on some SoCs.  Unfortunately that is
a big task and as far as I know, no-one has taken it
on as yet.  So in the meantime this driver is still
in here.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: max1363 add software ring buffer support using ring_sw

Changes since V2:
* Moved to new registration methodology.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: lis3l02dq ring buffer and data ready trigger support

Example of relatively common case of device sampling
based on internal clock and providing a data ready
signal to indicate that new data is available to be
read out.

Generic trigger approach used to allow other devices
to be sampled 'at the same time' as this the accelerometer.
This is very useful in various motion estimation algorithms.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: Ring buffer: Initial pass at rarely locked ring buffer

Please note this ring buffer implementation is very much a
work in progress (and hence RFC).  In it's current form
it is stable and reasonably efficient.  There are a couple
of unlikely cases that will lead to more data being lost
that is strictly necessary. The target was for the case
of requiring regular sampling even during user space reads.

All comments welcome.

The intention is to make this only one of several
implementations with run time selection.  For now there
is only one, so it is hard coded into the drivers using it.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: Trigger support added to core.

Add general registration support for IIO triggers.  These
are currently only used to initialize a 'poll' of a given
device.  Examples include the lis3l02dq's data ready signal
being used to initialize a read and gpio triggers being
used to allow externally synchronized sensor reading.

Each trigger can cause any number of 'consumer' devices
to be polled with each storing data into a related ring
buffer.

Two stage triggering is supported with 'fast' and 'slow'
paths.  The first is used for things like pulling a data
hold line high and the second for actual read which
may take far longer.

Changes since V2:
* As with IIO triggers now use a registration approach
  much closer to that of input leading to cleaner code.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: VTI sca3000 series accelerometer driver (spi)

Example of how a device with a hardware ring buffer is
handled within IIO.

Changes since V2:
* Moved to new registration functions giving much cleaner
  interface.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: Add generic ring buffer support to the IIO core

This provides a unified interface for hardware and software
ring buffers.

Changes since V2:
* Moved to a more consistent structure.  Now the ring buffer
  has an associated struct device which is a child of the
  relevant iio_dev.  This in turn has two children, one
  for the event interface and one for the access interface.
  These two interfaces are now managed via cdev structures.

* Numerous minor cleanups

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: kxsd9 accelerometer minimal support

This provides only very minimal support for this device.
Note that an alternate driver has been posted to the input
mailing list.

When the original LMKL discussion that led to the descision
to develop IIO occured, the question on whether the differing
requirements of IIO and input drivers made it a good idea
to have unified drivers was left as an open question.
It still is.  All opinions on this question welcome.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: lis3l02dq accelerometer core support

A later patch in the series will add data ready triggering
and ring buffer support.

This core patch provides an event interface and sysfs
based reading of values.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: tsl2561 digital light sensor core support

This is a pretty minimalist example of an IIO driver.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: max1363 ADC driver

Core support for MAX1361, MAX1362, MAX1363, MAX1364,
MAX1136, MAX1137, MAX1138, MAX1139, MAX1236, MAX1237,
MAX1238, MAX1239.

Ring buffer support later in series.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: IIO: core support for device registration and management

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

staging: Make some structures static

This was done using a semantic patch (http://coccinelle.lip6.fr/) that
checks that the declaration is not inside a function definition, that the
defined variable is not exported using EXPORTED_SYMBOL, etc, and that the
defined variable does not occur in any other file.  If these conditions
hold, static is added before the declaration.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt{2860,2870,3070}sta: Remove unused CRC code

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2860: Fix test in rt_ioctl_siwfrag()

The test always evaluated to true.

MIN_FRAG_THRESHOLD is defined 256,
MAX_FRAG_THRESHOLD is defined 2346

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: remove no longer needed rt3070 driver

rt2870 handles now all rt2870/rt3070 chipsets.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: remove old firmware

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxx70: merge rt3070 with rt2870

* remove RT30xx ifdefs
* add -DRT3070 to rt2870's EXTRA_CFLAGS
* because of changes in the way that hardware is initialized/accessed
  rt3070 driver's firmware should be now also used by rt2870 driver
  (this is also done by newer out-of-tree vendor driver versions, i.e.
  2.1.0.0, historically in-kernel driver was based on 1.4.0.0 version)
* change RT28xx_CHIP_NAME to RTxx70
* update rt2870's help entry text
* add MODULE_ALIAS("rt3070sta") to rt2870
* update rt3070's dependencies

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: add Antenna Diversity support

rt3070:
* remove non-working AntDiversity config parameter
* remove unused bRxAntDiversity field from COMMON_CONFIG

rt2870:
* propagate Antenna Diversity support from rt3070

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: add eFuse support

rt3070:
* remove unused bEEPROMFile field from RTMP_ADAPTER

rt2870:
* propagate eFuse support from rt3070

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxxxx: remove unused AsicAntenna{Select,Setting}()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: remove SHOW_ADHOC_ENTRY_INFO support

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: remove unused RT_CMD_SET_* internal commands

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: remove unused MiniportDataMMRequest()

Then remove no longer needed MlmeDataHardTransmit().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: LinkUp() fixes

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: rt_ioctl_siwencode() fixes

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: MlmeAssocReqAction() fixes for wpa_supplicant support

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: MlmeCheckPsmChange() fix

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: MlmeSelectTxRateTable() fix

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: BssTableSetEntry() fix

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: AsicSwitchChannel() fix

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0 fix BACapability policy handling

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: fix fOP_STATUS_DOZE flag handling

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: fix BPP_R66 register handling

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: fix GTK length check in ParseKeyData()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt28x0: add SIOCGIWNAME support to rt_ioctl_giwscan()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: add fRTUSB_BULK_OUT_DATA_NORMAL_5 quirk

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: use internal command for AsicUpdateProtect()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: add remaining rt2870 device ids

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: remove needless EFUSE_TAG register read

* remove write-only EFuseTag field from RTMP_ADAPTER
* remove needless EFUSE_TAG register read

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: AsicSetSlotTime() fix

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: WEP fixes

Propagate WEP fixes from rt28[67]0 to rt3070.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: fix PID checking in RTUSBEnqueueCmdFromNdis()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt3070: update allowed channels list for Japan

rt3070 driver allows use of 5G channel 34 while rt{286,287,309}0
drivers don't and quick googling seems to confirm the limitation.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxxxx: RTMPGetRalinkAuthModeStr() fixes

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxx70: unify NICInitRT30xxRFRegisters()

Unify RT30xx and !RT30xx code in NICInitRT30xxRFRegisters().

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxxxx: unify AsicSwitchChannel()

Unify RT30xx and !RT30xx code in AsicSwitchChannel().

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxxxx: unify AsicRxAntEvalTimeout()

Unify RT30xx and !RT30xx code in AsicRxAntEvalTimeout().

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxxx0: remove unused code

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxxx0: remove private ioctls

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtxxx0: remove private debugging ioctls

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>