/**
* EepromWriteByte - Write a byte to the ET1310's EEPROM
- * @pAdapter: pointer to our private adapter structure
+ * @etdev: pointer to our private adapter structure
* @unAddress: the address to write
* @bData: the value to write
* @unEepronId: the ID of the EEPROM
*
* Returns SUCCESS or FAILURE
*/
-int32_t EepromWriteByte(struct et131x_adapter *pAdapter, uint32_t unAddress,
+int32_t EepromWriteByte(struct et131x_adapter *etdev, uint32_t unAddress,
uint8_t bData, uint32_t unEepromId,
uint32_t unAddressingMode)
{
- struct pci_dev *pdev = pAdapter->pdev;
+ struct pci_dev *pdev = etdev->pdev;
int32_t nIndex;
int32_t nRetries;
int32_t nError = false;
* so we do a blind write for load bug.
*/
if (bStatus & LBCIF_STATUS_GENERAL_ERROR
- && pAdapter->RevisionID == 0) {
+ && etdev->RevisionID == 0) {
break;
}
/**
* EepromReadByte - Read a byte from the ET1310's EEPROM
- * @pAdapter: pointer to our private adapter structure
+ * @etdev: pointer to our private adapter structure
* @unAddress: the address from which to read
* @pbData: a pointer to a byte in which to store the value of the read
* @unEepronId: the ID of the EEPROM
*
* Returns SUCCESS or FAILURE
*/
-int32_t EepromReadByte(struct et131x_adapter *pAdapter, uint32_t unAddress,
+int32_t EepromReadByte(struct et131x_adapter *etdev, uint32_t unAddress,
uint8_t *pbData, uint32_t unEepromId,
uint32_t unAddressingMode)
{
- struct pci_dev *pdev = pAdapter->pdev;
+ struct pci_dev *pdev = etdev->pdev;
int32_t nIndex;
int32_t nError = 0;
uint8_t bControl;
* ConfigGlobalRegs - Used to configure the global registers on the JAGCore
* @pAdpater: pointer to our adapter structure
*/
-void ConfigGlobalRegs(struct et131x_adapter *pAdapter)
+void ConfigGlobalRegs(struct et131x_adapter *etdev)
{
- struct _GLOBAL_t __iomem *pGbl = &pAdapter->CSRAddress->global;
+ struct _GLOBAL_t __iomem *pGbl = &etdev->CSRAddress->global;
DBG_ENTER(et131x_dbginfo);
- if (pAdapter->RegistryPhyLoopbk == false) {
- if (pAdapter->RegistryJumboPacket < 2048) {
+ if (etdev->RegistryPhyLoopbk == false) {
+ if (etdev->RegistryJumboPacket < 2048) {
/* Tx / RxDMA and Tx/Rx MAC interfaces have a 1k word
* block of RAM that the driver can split between Tx
* and Rx as it desires. Our default is to split it
* 50/50:
*/
writel(0, &pGbl->rxq_start_addr.value);
- writel(pAdapter->RegistryRxMemEnd,
+ writel(etdev->RegistryRxMemEnd,
&pGbl->rxq_end_addr.value);
- writel(pAdapter->RegistryRxMemEnd + 1,
+ writel(etdev->RegistryRxMemEnd + 1,
&pGbl->txq_start_addr.value);
writel(INTERNAL_MEM_SIZE - 1,
&pGbl->txq_end_addr.value);
- } else if (pAdapter->RegistryJumboPacket < 8192) {
+ } else if (etdev->RegistryJumboPacket < 8192) {
/* For jumbo packets > 2k but < 8k, split 50-50. */
writel(0, &pGbl->rxq_start_addr.value);
writel(INTERNAL_MEM_RX_OFFSET,
/**
* ConfigMMCRegs - Used to configure the main memory registers in the JAGCore
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void ConfigMMCRegs(struct et131x_adapter *pAdapter)
+void ConfigMMCRegs(struct et131x_adapter *etdev)
{
MMC_CTRL_t mmc_ctrl = { 0 };
mmc_ctrl.bits.arb_disable = 0x0;
mmc_ctrl.bits.mmc_enable = 0x1;
- writel(mmc_ctrl.value, &pAdapter->CSRAddress->mmc.mmc_ctrl.value);
+ writel(mmc_ctrl.value, &etdev->CSRAddress->mmc.mmc_ctrl.value);
DBG_LEAVE(et131x_dbginfo);
}
* ConfigMacRegs1 - Initialize the first part of MAC regs
* @pAdpater: pointer to our adapter structure
*/
-void ConfigMACRegs1(struct et131x_adapter *pAdapter)
+void ConfigMACRegs1(struct et131x_adapter *etdev)
{
- struct _MAC_t __iomem *pMac = &pAdapter->CSRAddress->mac;
+ struct _MAC_t __iomem *pMac = &etdev->CSRAddress->mac;
MAC_STATION_ADDR1_t station1;
MAC_STATION_ADDR2_t station2;
MAC_IPG_t ipg;
* station address is used for generating and checking pause control
* packets.
*/
- station2.bits.Octet1 = pAdapter->CurrentAddress[0];
- station2.bits.Octet2 = pAdapter->CurrentAddress[1];
- station1.bits.Octet3 = pAdapter->CurrentAddress[2];
- station1.bits.Octet4 = pAdapter->CurrentAddress[3];
- station1.bits.Octet5 = pAdapter->CurrentAddress[4];
- station1.bits.Octet6 = pAdapter->CurrentAddress[5];
+ station2.bits.Octet1 = etdev->CurrentAddress[0];
+ station2.bits.Octet2 = etdev->CurrentAddress[1];
+ station1.bits.Octet3 = etdev->CurrentAddress[2];
+ station1.bits.Octet4 = etdev->CurrentAddress[3];
+ station1.bits.Octet5 = etdev->CurrentAddress[4];
+ station1.bits.Octet6 = etdev->CurrentAddress[5];
writel(station1.value, &pMac->station_addr_1.value);
writel(station2.value, &pMac->station_addr_2.value);
* Packets larger than (RegistryJumboPacket) that do not contain a
* VLAN ID will be dropped by the Rx function.
*/
- writel(pAdapter->RegistryJumboPacket + 4, &pMac->max_fm_len.value);
+ writel(etdev->RegistryJumboPacket + 4, &pMac->max_fm_len.value);
/* clear out MAC config reset */
writel(0, &pMac->cfg1.value);
* ConfigMacRegs2 - Initialize the second part of MAC regs
* @pAdpater: pointer to our adapter structure
*/
-void ConfigMACRegs2(struct et131x_adapter *pAdapter)
+void ConfigMACRegs2(struct et131x_adapter *etdev)
{
int32_t delay = 0;
- struct _MAC_t __iomem *pMac = &pAdapter->CSRAddress->mac;
+ struct _MAC_t __iomem *pMac = &etdev->CSRAddress->mac;
MAC_CFG1_t cfg1;
MAC_CFG2_t cfg2;
MAC_IF_CTRL_t ifctrl;
DBG_ENTER(et131x_dbginfo);
- ctl.value = readl(&pAdapter->CSRAddress->txmac.ctl.value);
+ ctl.value = readl(&etdev->CSRAddress->txmac.ctl.value);
cfg1.value = readl(&pMac->cfg1.value);
cfg2.value = readl(&pMac->cfg2.value);
ifctrl.value = readl(&pMac->if_ctrl.value);
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
cfg2.bits.if_mode = 0x2;
ifctrl.bits.phy_mode = 0x0;
} else {
/* Set up flow control */
cfg1.bits.tx_flow = 0x1;
- if ((pAdapter->FlowControl == RxOnly) ||
- (pAdapter->FlowControl == Both)) {
+ if ((etdev->FlowControl == RxOnly) ||
+ (etdev->FlowControl == Both)) {
cfg1.bits.rx_flow = 0x1;
} else {
cfg1.bits.rx_flow = 0x0;
*/
cfg2.bits.len_check = 0x1;
- if (pAdapter->RegistryPhyLoopbk == false) {
+ if (etdev->RegistryPhyLoopbk == false) {
cfg2.bits.pad_crc = 0x1;
cfg2.bits.crc_enable = 0x1;
} else {
}
/* 1 - full duplex, 0 - half-duplex */
- cfg2.bits.full_duplex = pAdapter->uiDuplexMode;
- ifctrl.bits.ghd_mode = !pAdapter->uiDuplexMode;
+ cfg2.bits.full_duplex = etdev->uiDuplexMode;
+ ifctrl.bits.ghd_mode = !etdev->uiDuplexMode;
writel(ifctrl.value, &pMac->if_ctrl.value);
writel(cfg2.value, &pMac->cfg2.value);
DBG_TRACE(et131x_dbginfo,
"Speed %d, Dup %d, CFG1 0x%08x, CFG2 0x%08x, if_ctrl 0x%08x\n",
- pAdapter->uiLinkSpeed, pAdapter->uiDuplexMode,
+ etdev->uiLinkSpeed, etdev->uiDuplexMode,
readl(&pMac->cfg1.value), readl(&pMac->cfg2.value),
readl(&pMac->if_ctrl.value));
/* Enable TXMAC */
ctl.bits.txmac_en = 0x1;
ctl.bits.fc_disable = 0x1;
- writel(ctl.value, &pAdapter->CSRAddress->txmac.ctl.value);
+ writel(ctl.value, &etdev->CSRAddress->txmac.ctl.value);
/* Ready to start the RXDMA/TXDMA engine */
- if (!MP_TEST_FLAG(pAdapter, fMP_ADAPTER_LOWER_POWER)) {
- et131x_rx_dma_enable(pAdapter);
- et131x_tx_dma_enable(pAdapter);
+ if (!MP_TEST_FLAG(etdev, fMP_ADAPTER_LOWER_POWER)) {
+ et131x_rx_dma_enable(etdev);
+ et131x_tx_dma_enable(etdev);
} else {
DBG_WARNING(et131x_dbginfo,
"Didn't enable Rx/Tx due to low-power mode\n");
DBG_LEAVE(et131x_dbginfo);
}
-void ConfigRxMacRegs(struct et131x_adapter *pAdapter)
+void ConfigRxMacRegs(struct et131x_adapter *etdev)
{
- struct _RXMAC_t __iomem *pRxMac = &pAdapter->CSRAddress->rxmac;
+ struct _RXMAC_t __iomem *pRxMac = &etdev->CSRAddress->rxmac;
RXMAC_WOL_SA_LO_t sa_lo;
RXMAC_WOL_SA_HI_t sa_hi;
RXMAC_PF_CTRL_t pf_ctrl = { 0 };
writel(0, &pRxMac->mask4_word3);
/* Lets setup the WOL Source Address */
- sa_lo.bits.sa3 = pAdapter->CurrentAddress[2];
- sa_lo.bits.sa4 = pAdapter->CurrentAddress[3];
- sa_lo.bits.sa5 = pAdapter->CurrentAddress[4];
- sa_lo.bits.sa6 = pAdapter->CurrentAddress[5];
+ sa_lo.bits.sa3 = etdev->CurrentAddress[2];
+ sa_lo.bits.sa4 = etdev->CurrentAddress[3];
+ sa_lo.bits.sa5 = etdev->CurrentAddress[4];
+ sa_lo.bits.sa6 = etdev->CurrentAddress[5];
writel(sa_lo.value, &pRxMac->sa_lo.value);
- sa_hi.bits.sa1 = pAdapter->CurrentAddress[0];
- sa_hi.bits.sa2 = pAdapter->CurrentAddress[1];
+ sa_hi.bits.sa1 = etdev->CurrentAddress[0];
+ sa_hi.bits.sa2 = etdev->CurrentAddress[1];
writel(sa_hi.value, &pRxMac->sa_hi.value);
/* Disable all Packet Filtering */
writel(0, &pRxMac->pf_ctrl.value);
/* Let's initialize the Unicast Packet filtering address */
- if (pAdapter->PacketFilter & ET131X_PACKET_TYPE_DIRECTED) {
- SetupDeviceForUnicast(pAdapter);
+ if (etdev->PacketFilter & ET131X_PACKET_TYPE_DIRECTED) {
+ SetupDeviceForUnicast(etdev);
pf_ctrl.bits.filter_uni_en = 1;
} else {
writel(0, &pRxMac->uni_pf_addr1.value);
}
/* Let's initialize the Multicast hash */
- if (pAdapter->PacketFilter & ET131X_PACKET_TYPE_ALL_MULTICAST) {
+ if (etdev->PacketFilter & ET131X_PACKET_TYPE_ALL_MULTICAST) {
pf_ctrl.bits.filter_multi_en = 0;
} else {
pf_ctrl.bits.filter_multi_en = 1;
- SetupDeviceForMulticast(pAdapter);
+ SetupDeviceForMulticast(etdev);
}
/* Runt packet filtering. Didn't work in version A silicon. */
pf_ctrl.bits.min_pkt_size = NIC_MIN_PACKET_SIZE + 4;
pf_ctrl.bits.filter_frag_en = 1;
- if (pAdapter->RegistryJumboPacket > 8192) {
+ if (etdev->RegistryJumboPacket > 8192) {
RXMAC_MCIF_CTRL_MAX_SEG_t mcif_ctrl_max_seg;
/* In order to transmit jumbo packets greater than 8k, the
* bit 16: Receive frame truncated.
* bit 17: Drop packet enable
*/
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_100MBPS)
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_100MBPS)
writel(0x30038, &pRxMac->mif_ctrl.value);
else
writel(0x30030, &pRxMac->mif_ctrl.value);
DBG_LEAVE(et131x_dbginfo);
}
-void ConfigTxMacRegs(struct et131x_adapter *pAdapter)
+void ConfigTxMacRegs(struct et131x_adapter *etdev)
{
- struct _TXMAC_t __iomem *pTxMac = &pAdapter->CSRAddress->txmac;
+ struct _TXMAC_t __iomem *pTxMac = &etdev->CSRAddress->txmac;
TXMAC_CF_PARAM_t Local;
DBG_ENTER(et131x_dbginfo);
* cfpt - control frame pause timer set to 64 (0x40)
* cfep - control frame extended pause timer set to 0x0
*/
- if (pAdapter->FlowControl == None) {
+ if (etdev->FlowControl == None) {
writel(0, &pTxMac->cf_param.value);
} else {
Local.bits.cfpt = 0x40;
DBG_LEAVE(et131x_dbginfo);
}
-void ConfigMacStatRegs(struct et131x_adapter *pAdapter)
+void ConfigMacStatRegs(struct et131x_adapter *etdev)
{
struct _MAC_STAT_t __iomem *pDevMacStat =
- &pAdapter->CSRAddress->macStat;
+ &etdev->CSRAddress->macStat;
DBG_ENTER(et131x_dbginfo);
DBG_LEAVE(et131x_dbginfo);
}
-void ConfigFlowControl(struct et131x_adapter *pAdapter)
+void ConfigFlowControl(struct et131x_adapter *etdev)
{
- if (pAdapter->uiDuplexMode == 0) {
- pAdapter->FlowControl = None;
+ if (etdev->uiDuplexMode == 0) {
+ etdev->FlowControl = None;
} else {
char RemotePause, RemoteAsyncPause;
- ET1310_PhyAccessMiBit(pAdapter,
+ ET1310_PhyAccessMiBit(etdev,
TRUEPHY_BIT_READ, 5, 10, &RemotePause);
- ET1310_PhyAccessMiBit(pAdapter,
+ ET1310_PhyAccessMiBit(etdev,
TRUEPHY_BIT_READ, 5, 11,
&RemoteAsyncPause);
if ((RemotePause == TRUEPHY_BIT_SET) &&
(RemoteAsyncPause == TRUEPHY_BIT_SET)) {
- pAdapter->FlowControl = pAdapter->RegistryFlowControl;
+ etdev->FlowControl = etdev->RegistryFlowControl;
} else if ((RemotePause == TRUEPHY_BIT_SET) &&
(RemoteAsyncPause == TRUEPHY_BIT_CLEAR)) {
- if (pAdapter->RegistryFlowControl == Both)
- pAdapter->FlowControl = Both;
+ if (etdev->RegistryFlowControl == Both)
+ etdev->FlowControl = Both;
else
- pAdapter->FlowControl = None;
+ etdev->FlowControl = None;
} else if ((RemotePause == TRUEPHY_BIT_CLEAR) &&
(RemoteAsyncPause == TRUEPHY_BIT_CLEAR)) {
- pAdapter->FlowControl = None;
+ etdev->FlowControl = None;
} else {/* if (RemotePause == TRUEPHY_CLEAR_BIT &&
RemoteAsyncPause == TRUEPHY_SET_BIT) */
- if (pAdapter->RegistryFlowControl == Both)
- pAdapter->FlowControl = RxOnly;
+ if (etdev->RegistryFlowControl == Both)
+ etdev->FlowControl = RxOnly;
else
- pAdapter->FlowControl = None;
+ etdev->FlowControl = None;
}
}
}
/**
* UpdateMacStatHostCounters - Update the local copy of the statistics
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*/
-void UpdateMacStatHostCounters(struct et131x_adapter *pAdapter)
+void UpdateMacStatHostCounters(struct et131x_adapter *etdev)
{
- struct _ce_stats_t *stats = &pAdapter->Stats;
+ struct _ce_stats_t *stats = &etdev->Stats;
struct _MAC_STAT_t __iomem *pDevMacStat =
- &pAdapter->CSRAddress->macStat;
+ &etdev->CSRAddress->macStat;
stats->collisions += readl(&pDevMacStat->TNcl);
stats->first_collision += readl(&pDevMacStat->TScl);
/**
* HandleMacStatInterrupt
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*
* One of the MACSTAT counters has wrapped. Update the local copy of
* the statistics held in the adapter structure, checking the "wrap"
* bit for each counter.
*/
-void HandleMacStatInterrupt(struct et131x_adapter *pAdapter)
+void HandleMacStatInterrupt(struct et131x_adapter *etdev)
{
MAC_STAT_REG_1_t Carry1;
MAC_STAT_REG_2_t Carry2;
/* Read the interrupt bits from the register(s). These are Clear On
* Write.
*/
- Carry1.value = readl(&pAdapter->CSRAddress->macStat.Carry1.value);
- Carry2.value = readl(&pAdapter->CSRAddress->macStat.Carry2.value);
+ Carry1.value = readl(&etdev->CSRAddress->macStat.Carry1.value);
+ Carry2.value = readl(&etdev->CSRAddress->macStat.Carry2.value);
- writel(Carry1.value, &pAdapter->CSRAddress->macStat.Carry1.value);
- writel(Carry2.value, &pAdapter->CSRAddress->macStat.Carry2.value);
+ writel(Carry1.value, &etdev->CSRAddress->macStat.Carry1.value);
+ writel(Carry2.value, &etdev->CSRAddress->macStat.Carry2.value);
/* We need to do update the host copy of all the MAC_STAT counters.
* For each counter, check it's overflow bit. If the overflow bit is
* block indicates that one of the counters has wrapped.
*/
if (Carry1.bits.rfcs)
- pAdapter->Stats.code_violations += COUNTER_WRAP_16_BIT;
+ etdev->Stats.code_violations += COUNTER_WRAP_16_BIT;
if (Carry1.bits.raln)
- pAdapter->Stats.alignment_err += COUNTER_WRAP_12_BIT;
+ etdev->Stats.alignment_err += COUNTER_WRAP_12_BIT;
if (Carry1.bits.rflr)
- pAdapter->Stats.length_err += COUNTER_WRAP_16_BIT;
+ etdev->Stats.length_err += COUNTER_WRAP_16_BIT;
if (Carry1.bits.rfrg)
- pAdapter->Stats.other_errors += COUNTER_WRAP_16_BIT;
+ etdev->Stats.other_errors += COUNTER_WRAP_16_BIT;
if (Carry1.bits.rcde)
- pAdapter->Stats.crc_err += COUNTER_WRAP_16_BIT;
+ etdev->Stats.crc_err += COUNTER_WRAP_16_BIT;
if (Carry1.bits.rovr)
- pAdapter->Stats.rx_ov_flow += COUNTER_WRAP_16_BIT;
+ etdev->Stats.rx_ov_flow += COUNTER_WRAP_16_BIT;
if (Carry1.bits.rdrp)
- pAdapter->Stats.norcvbuf += COUNTER_WRAP_16_BIT;
+ etdev->Stats.norcvbuf += COUNTER_WRAP_16_BIT;
if (Carry2.bits.tovr)
- pAdapter->Stats.max_pkt_error += COUNTER_WRAP_12_BIT;
+ etdev->Stats.max_pkt_error += COUNTER_WRAP_12_BIT;
if (Carry2.bits.tund)
- pAdapter->Stats.tx_uflo += COUNTER_WRAP_12_BIT;
+ etdev->Stats.tx_uflo += COUNTER_WRAP_12_BIT;
if (Carry2.bits.tscl)
- pAdapter->Stats.first_collision += COUNTER_WRAP_12_BIT;
+ etdev->Stats.first_collision += COUNTER_WRAP_12_BIT;
if (Carry2.bits.tdfr)
- pAdapter->Stats.tx_deferred += COUNTER_WRAP_12_BIT;
+ etdev->Stats.tx_deferred += COUNTER_WRAP_12_BIT;
if (Carry2.bits.tmcl)
- pAdapter->Stats.excessive_collisions += COUNTER_WRAP_12_BIT;
+ etdev->Stats.excessive_collisions += COUNTER_WRAP_12_BIT;
if (Carry2.bits.tlcl)
- pAdapter->Stats.late_collisions += COUNTER_WRAP_12_BIT;
+ etdev->Stats.late_collisions += COUNTER_WRAP_12_BIT;
if (Carry2.bits.tncl)
- pAdapter->Stats.collisions += COUNTER_WRAP_12_BIT;
+ etdev->Stats.collisions += COUNTER_WRAP_12_BIT;
DBG_LEAVE(et131x_dbginfo);
}
-void SetupDeviceForMulticast(struct et131x_adapter *pAdapter)
+void SetupDeviceForMulticast(struct et131x_adapter *etdev)
{
- struct _RXMAC_t __iomem *rxmac = &pAdapter->CSRAddress->rxmac;
+ struct _RXMAC_t __iomem *rxmac = &etdev->CSRAddress->rxmac;
uint32_t nIndex;
uint32_t result;
uint32_t hash1 = 0;
* specified) then we should pass NO multi-cast addresses to the
* driver.
*/
- if (pAdapter->PacketFilter & ET131X_PACKET_TYPE_MULTICAST) {
+ if (etdev->PacketFilter & ET131X_PACKET_TYPE_MULTICAST) {
DBG_VERBOSE(et131x_dbginfo,
"MULTICAST flag is set, MCCount: %d\n",
- pAdapter->MCAddressCount);
+ etdev->MCAddressCount);
/* Loop through our multicast array and set up the device */
- for (nIndex = 0; nIndex < pAdapter->MCAddressCount; nIndex++) {
+ for (nIndex = 0; nIndex < etdev->MCAddressCount; nIndex++) {
DBG_VERBOSE(et131x_dbginfo,
"MCList[%d]: %02x:%02x:%02x:%02x:%02x:%02x\n",
nIndex,
- pAdapter->MCList[nIndex][0],
- pAdapter->MCList[nIndex][1],
- pAdapter->MCList[nIndex][2],
- pAdapter->MCList[nIndex][3],
- pAdapter->MCList[nIndex][4],
- pAdapter->MCList[nIndex][5]);
+ etdev->MCList[nIndex][0],
+ etdev->MCList[nIndex][1],
+ etdev->MCList[nIndex][2],
+ etdev->MCList[nIndex][3],
+ etdev->MCList[nIndex][4],
+ etdev->MCList[nIndex][5]);
- result = ether_crc(6, pAdapter->MCList[nIndex]);
+ result = ether_crc(6, etdev->MCList[nIndex]);
result = (result & 0x3F800000) >> 23;
}
/* Write out the new hash to the device */
- pm_csr.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
+ pm_csr.value = readl(&etdev->CSRAddress->global.pm_csr.value);
if (pm_csr.bits.pm_phy_sw_coma == 0) {
writel(hash1, &rxmac->multi_hash1);
writel(hash2, &rxmac->multi_hash2);
DBG_LEAVE(et131x_dbginfo);
}
-void SetupDeviceForUnicast(struct et131x_adapter *pAdapter)
+void SetupDeviceForUnicast(struct et131x_adapter *etdev)
{
- struct _RXMAC_t __iomem *rxmac = &pAdapter->CSRAddress->rxmac;
+ struct _RXMAC_t __iomem *rxmac = &etdev->CSRAddress->rxmac;
RXMAC_UNI_PF_ADDR1_t uni_pf1;
RXMAC_UNI_PF_ADDR2_t uni_pf2;
RXMAC_UNI_PF_ADDR3_t uni_pf3;
* Set up unicast packet filter reg 3 to be the octets 2 - 5 of the
* MAC address for first address
*/
- uni_pf3.bits.addr1_1 = pAdapter->CurrentAddress[0];
- uni_pf3.bits.addr1_2 = pAdapter->CurrentAddress[1];
- uni_pf3.bits.addr2_1 = pAdapter->CurrentAddress[0];
- uni_pf3.bits.addr2_2 = pAdapter->CurrentAddress[1];
-
- uni_pf2.bits.addr2_3 = pAdapter->CurrentAddress[2];
- uni_pf2.bits.addr2_4 = pAdapter->CurrentAddress[3];
- uni_pf2.bits.addr2_5 = pAdapter->CurrentAddress[4];
- uni_pf2.bits.addr2_6 = pAdapter->CurrentAddress[5];
-
- uni_pf1.bits.addr1_3 = pAdapter->CurrentAddress[2];
- uni_pf1.bits.addr1_4 = pAdapter->CurrentAddress[3];
- uni_pf1.bits.addr1_5 = pAdapter->CurrentAddress[4];
- uni_pf1.bits.addr1_6 = pAdapter->CurrentAddress[5];
-
- pm_csr.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
+ uni_pf3.bits.addr1_1 = etdev->CurrentAddress[0];
+ uni_pf3.bits.addr1_2 = etdev->CurrentAddress[1];
+ uni_pf3.bits.addr2_1 = etdev->CurrentAddress[0];
+ uni_pf3.bits.addr2_2 = etdev->CurrentAddress[1];
+
+ uni_pf2.bits.addr2_3 = etdev->CurrentAddress[2];
+ uni_pf2.bits.addr2_4 = etdev->CurrentAddress[3];
+ uni_pf2.bits.addr2_5 = etdev->CurrentAddress[4];
+ uni_pf2.bits.addr2_6 = etdev->CurrentAddress[5];
+
+ uni_pf1.bits.addr1_3 = etdev->CurrentAddress[2];
+ uni_pf1.bits.addr1_4 = etdev->CurrentAddress[3];
+ uni_pf1.bits.addr1_5 = etdev->CurrentAddress[4];
+ uni_pf1.bits.addr1_6 = etdev->CurrentAddress[5];
+
+ pm_csr.value = readl(&etdev->CSRAddress->global.pm_csr.value);
if (pm_csr.bits.pm_phy_sw_coma == 0) {
writel(uni_pf1.value, &rxmac->uni_pf_addr1.value);
writel(uni_pf2.value, &rxmac->uni_pf_addr2.value);
}
}
-void et131x_Mii_check(struct et131x_adapter *pAdapter,
+void et131x_Mii_check(struct et131x_adapter *etdev,
MI_BMSR_t bmsr, MI_BMSR_t bmsr_ints)
{
uint8_t ucLinkStatus;
if (bmsr_ints.bits.link_status) {
if (bmsr.bits.link_status) {
- pAdapter->PoMgmt.TransPhyComaModeOnBoot = 20;
+ etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
/* Update our state variables and indicate the
* connected state
*/
- spin_lock_irqsave(&pAdapter->Lock, lockflags);
+ spin_lock_irqsave(&etdev->Lock, lockflags);
- pAdapter->MediaState = NETIF_STATUS_MEDIA_CONNECT;
- MP_CLEAR_FLAG(pAdapter, fMP_ADAPTER_LINK_DETECTION);
+ etdev->MediaState = NETIF_STATUS_MEDIA_CONNECT;
+ MP_CLEAR_FLAG(etdev, fMP_ADAPTER_LINK_DETECTION);
- spin_unlock_irqrestore(&pAdapter->Lock, lockflags);
+ spin_unlock_irqrestore(&etdev->Lock, lockflags);
/* Don't indicate state if we're in loopback mode */
- if (pAdapter->RegistryPhyLoopbk == false)
- netif_carrier_on(pAdapter->netdev);
+ if (etdev->RegistryPhyLoopbk == false)
+ netif_carrier_on(etdev->netdev);
} else {
DBG_WARNING(et131x_dbginfo,
"Link down cable problem\n");
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_10MBPS) {
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_10MBPS) {
/* NOTE - Is there a way to query this without
* TruePHY?
- * && TRU_QueryCoreType(pAdapter->hTruePhy, 0) == EMI_TRUEPHY_A13O) {
+ * && TRU_QueryCoreType(etdev->hTruePhy, 0) == EMI_TRUEPHY_A13O) {
*/
uint16_t Register18;
- MiRead(pAdapter, 0x12, &Register18);
- MiWrite(pAdapter, 0x12, Register18 | 0x4);
- MiWrite(pAdapter, 0x10, Register18 | 0x8402);
- MiWrite(pAdapter, 0x11, Register18 | 511);
- MiWrite(pAdapter, 0x12, Register18);
+ MiRead(etdev, 0x12, &Register18);
+ MiWrite(etdev, 0x12, Register18 | 0x4);
+ MiWrite(etdev, 0x10, Register18 | 0x8402);
+ MiWrite(etdev, 0x11, Register18 | 511);
+ MiWrite(etdev, 0x12, Register18);
}
/* For the first N seconds of life, we are in "link
* in the LinkDetectionDPC).
*/
if ((MP_IS_FLAG_CLEAR
- (pAdapter, fMP_ADAPTER_LINK_DETECTION))
- || (pAdapter->MediaState ==
+ (etdev, fMP_ADAPTER_LINK_DETECTION))
+ || (etdev->MediaState ==
NETIF_STATUS_MEDIA_DISCONNECT)) {
- spin_lock_irqsave(&pAdapter->Lock, lockflags);
- pAdapter->MediaState =
+ spin_lock_irqsave(&etdev->Lock, lockflags);
+ etdev->MediaState =
NETIF_STATUS_MEDIA_DISCONNECT;
- spin_unlock_irqrestore(&pAdapter->Lock,
+ spin_unlock_irqrestore(&etdev->Lock,
lockflags);
/* Only indicate state if we're in loopback
* mode
*/
- if (pAdapter->RegistryPhyLoopbk == false)
- netif_carrier_off(pAdapter->netdev);
+ if (etdev->RegistryPhyLoopbk == false)
+ netif_carrier_off(etdev->netdev);
}
- pAdapter->uiLinkSpeed = 0;
- pAdapter->uiDuplexMode = 0;
+ etdev->uiLinkSpeed = 0;
+ etdev->uiDuplexMode = 0;
/* Free the packets being actively sent & stopped */
- et131x_free_busy_send_packets(pAdapter);
+ et131x_free_busy_send_packets(etdev);
/* Re-initialize the send structures */
- et131x_init_send(pAdapter);
+ et131x_init_send(etdev);
/* Reset the RFD list and re-start RU */
- et131x_reset_recv(pAdapter);
+ et131x_reset_recv(etdev);
/*
* Bring the device back to the state it was during
* way, when we get the auto-neg complete interrupt,
* we can complete init by calling ConfigMacREGS2.
*/
- et131x_soft_reset(pAdapter);
+ et131x_soft_reset(etdev);
/* Setup ET1310 as per the documentation */
- et131x_adapter_setup(pAdapter);
+ et131x_adapter_setup(etdev);
/* Setup the PHY into coma mode until the cable is
* plugged back in
*/
- if (pAdapter->RegistryPhyComa == 1)
- EnablePhyComa(pAdapter);
+ if (etdev->RegistryPhyComa == 1)
+ EnablePhyComa(etdev);
}
}
if (bmsr_ints.bits.auto_neg_complete ||
- (pAdapter->AiForceDpx == 3 && bmsr_ints.bits.link_status)) {
- if (bmsr.bits.auto_neg_complete || pAdapter->AiForceDpx == 3) {
- ET1310_PhyLinkStatus(pAdapter,
+ (etdev->AiForceDpx == 3 && bmsr_ints.bits.link_status)) {
+ if (bmsr.bits.auto_neg_complete || etdev->AiForceDpx == 3) {
+ ET1310_PhyLinkStatus(etdev,
&ucLinkStatus, &uiAutoNegStatus,
&uiSpeed, &uiDuplex, &uiMdiMdix,
&uiMasterSlave, &uiPolarity);
- pAdapter->uiLinkSpeed = uiSpeed;
- pAdapter->uiDuplexMode = uiDuplex;
+ etdev->uiLinkSpeed = uiSpeed;
+ etdev->uiDuplexMode = uiDuplex;
DBG_TRACE(et131x_dbginfo,
- "pAdapter->uiLinkSpeed 0x%04x, pAdapter->uiDuplex 0x%08x\n",
- pAdapter->uiLinkSpeed,
- pAdapter->uiDuplexMode);
+ "etdev->uiLinkSpeed 0x%04x, etdev->uiDuplex 0x%08x\n",
+ etdev->uiLinkSpeed,
+ etdev->uiDuplexMode);
- pAdapter->PoMgmt.TransPhyComaModeOnBoot = 20;
+ etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_10MBPS) {
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_10MBPS) {
/*
* NOTE - Is there a way to query this without
* TruePHY?
- * && TRU_QueryCoreType(pAdapter->hTruePhy, 0)== EMI_TRUEPHY_A13O) {
+ * && TRU_QueryCoreType(etdev->hTruePhy, 0)== EMI_TRUEPHY_A13O) {
*/
uint16_t Register18;
- MiRead(pAdapter, 0x12, &Register18);
- MiWrite(pAdapter, 0x12, Register18 | 0x4);
- MiWrite(pAdapter, 0x10, Register18 | 0x8402);
- MiWrite(pAdapter, 0x11, Register18 | 511);
- MiWrite(pAdapter, 0x12, Register18);
+ MiRead(etdev, 0x12, &Register18);
+ MiWrite(etdev, 0x12, Register18 | 0x4);
+ MiWrite(etdev, 0x10, Register18 | 0x8402);
+ MiWrite(etdev, 0x11, Register18 | 511);
+ MiWrite(etdev, 0x12, Register18);
}
- ConfigFlowControl(pAdapter);
+ ConfigFlowControl(etdev);
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS &&
- pAdapter->RegistryJumboPacket > 2048)
- ET1310_PhyAndOrReg(pAdapter, 0x16, 0xcfff,
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS &&
+ etdev->RegistryJumboPacket > 2048)
+ ET1310_PhyAndOrReg(etdev, 0x16, 0xcfff,
0x2000);
- SetRxDmaTimer(pAdapter);
- ConfigMACRegs2(pAdapter);
+ SetRxDmaTimer(etdev);
+ ConfigMACRegs2(etdev);
}
}
/**
* TPAL_SetPhy10HalfDuplex - Force the phy into 10 Base T Half Duplex mode.
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*
* Also sets the MAC so it is syncd up properly
*/
-void TPAL_SetPhy10HalfDuplex(struct et131x_adapter *pAdapter)
+void TPAL_SetPhy10HalfDuplex(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* First we need to turn off all other advertisement */
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Set our advertise values accordingly */
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_HALF);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_HALF);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
/**
* TPAL_SetPhy10FullDuplex - Force the phy into 10 Base T Full Duplex mode.
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*
* Also sets the MAC so it is syncd up properly
*/
-void TPAL_SetPhy10FullDuplex(struct et131x_adapter *pAdapter)
+void TPAL_SetPhy10FullDuplex(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* First we need to turn off all other advertisement */
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Set our advertise values accordingly */
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_FULL);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_FULL);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
/**
* TPAL_SetPhy10Force - Force Base-T FD mode WITHOUT using autonegotiation
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*/
-void TPAL_SetPhy10Force(struct et131x_adapter *pAdapter)
+void TPAL_SetPhy10Force(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* Disable autoneg */
- ET1310_PhyAutoNeg(pAdapter, false);
+ ET1310_PhyAutoNeg(etdev, false);
/* Disable all advertisement */
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Force 10 Mbps */
- ET1310_PhySpeedSelect(pAdapter, TRUEPHY_SPEED_10MBPS);
+ ET1310_PhySpeedSelect(etdev, TRUEPHY_SPEED_10MBPS);
/* Force Full duplex */
- ET1310_PhyDuplexMode(pAdapter, TRUEPHY_DUPLEX_FULL);
+ ET1310_PhyDuplexMode(etdev, TRUEPHY_DUPLEX_FULL);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
/**
* TPAL_SetPhy100HalfDuplex - Force 100 Base T Half Duplex mode.
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*
* Also sets the MAC so it is syncd up properly.
*/
-void TPAL_SetPhy100HalfDuplex(struct et131x_adapter *pAdapter)
+void TPAL_SetPhy100HalfDuplex(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* first we need to turn off all other advertisement */
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Set our advertise values accordingly */
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_HALF);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_HALF);
/* Set speed */
- ET1310_PhySpeedSelect(pAdapter, TRUEPHY_SPEED_100MBPS);
+ ET1310_PhySpeedSelect(etdev, TRUEPHY_SPEED_100MBPS);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
/**
* TPAL_SetPhy100FullDuplex - Force 100 Base T Full Duplex mode.
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*
* Also sets the MAC so it is syncd up properly
*/
-void TPAL_SetPhy100FullDuplex(struct et131x_adapter *pAdapter)
+void TPAL_SetPhy100FullDuplex(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* First we need to turn off all other advertisement */
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Set our advertise values accordingly */
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_FULL);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_FULL);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
/**
* TPAL_SetPhy100Force - Force 100 BaseT FD mode WITHOUT using autonegotiation
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*/
-void TPAL_SetPhy100Force(struct et131x_adapter *pAdapter)
+void TPAL_SetPhy100Force(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* Disable autoneg */
- ET1310_PhyAutoNeg(pAdapter, false);
+ ET1310_PhyAutoNeg(etdev, false);
/* Disable all advertisement */
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Force 100 Mbps */
- ET1310_PhySpeedSelect(pAdapter, TRUEPHY_SPEED_100MBPS);
+ ET1310_PhySpeedSelect(etdev, TRUEPHY_SPEED_100MBPS);
/* Force Full duplex */
- ET1310_PhyDuplexMode(pAdapter, TRUEPHY_DUPLEX_FULL);
+ ET1310_PhyDuplexMode(etdev, TRUEPHY_DUPLEX_FULL);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
/**
* TPAL_SetPhy1000FullDuplex - Force 1000 Base T Full Duplex mode
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*
* Also sets the MAC so it is syncd up properly.
*/
-void TPAL_SetPhy1000FullDuplex(struct et131x_adapter *pAdapter)
+void TPAL_SetPhy1000FullDuplex(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* first we need to turn off all other advertisement */
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* set our advertise values accordingly */
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_FULL);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_FULL);
/* power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
/**
* TPAL_SetPhyAutoNeg - Set phy to autonegotiation mode.
- * @pAdapter: pointer to the adapter structure
+ * @etdev: pointer to the adapter structure
*/
-void TPAL_SetPhyAutoNeg(struct et131x_adapter *pAdapter)
+void TPAL_SetPhyAutoNeg(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/* Turn on advertisement of all capabilities */
- ET1310_PhyAdvertise10BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_BOTH);
+ ET1310_PhyAdvertise10BaseT(etdev, TRUEPHY_ADV_DUPLEX_BOTH);
- ET1310_PhyAdvertise100BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_BOTH);
+ ET1310_PhyAdvertise100BaseT(etdev, TRUEPHY_ADV_DUPLEX_BOTH);
- if (pAdapter->DeviceID != ET131X_PCI_DEVICE_ID_FAST)
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_FULL);
+ if (etdev->DeviceID != ET131X_PCI_DEVICE_ID_FAST)
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_FULL);
else
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Make sure auto-neg is ON (it is disabled in FORCE modes) */
- ET1310_PhyAutoNeg(pAdapter, true);
+ ET1310_PhyAutoNeg(etdev, true);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
DBG_LEAVE(et131x_dbginfo);
}
};
/* condensed version of the phy initialization routine */
-void ET1310_PhyInit(struct et131x_adapter *pAdapter)
+void ET1310_PhyInit(struct et131x_adapter *etdev)
{
uint16_t usData, usIndex;
- if (pAdapter == NULL)
+ if (etdev == NULL)
return;
/* get the identity (again ?) */
- MiRead(pAdapter, PHY_ID_1, &usData);
- MiRead(pAdapter, PHY_ID_2, &usData);
+ MiRead(etdev, PHY_ID_1, &usData);
+ MiRead(etdev, PHY_ID_2, &usData);
/* what does this do/achieve ? */
- MiRead(pAdapter, PHY_MPHY_CONTROL_REG, &usData); /* should read 0002 */
- MiWrite(pAdapter, PHY_MPHY_CONTROL_REG, 0x0006);
+ MiRead(etdev, PHY_MPHY_CONTROL_REG, &usData); /* should read 0002 */
+ MiWrite(etdev, PHY_MPHY_CONTROL_REG, 0x0006);
/* read modem register 0402, should I do something with the return
data ? */
- MiWrite(pAdapter, PHY_INDEX_REG, 0x0402);
- MiRead(pAdapter, PHY_DATA_REG, &usData);
+ MiWrite(etdev, PHY_INDEX_REG, 0x0402);
+ MiRead(etdev, PHY_DATA_REG, &usData);
/* what does this do/achieve ? */
- MiWrite(pAdapter, PHY_MPHY_CONTROL_REG, 0x0002);
+ MiWrite(etdev, PHY_MPHY_CONTROL_REG, 0x0002);
/* get the identity (again ?) */
- MiRead(pAdapter, PHY_ID_1, &usData);
- MiRead(pAdapter, PHY_ID_2, &usData);
+ MiRead(etdev, PHY_ID_1, &usData);
+ MiRead(etdev, PHY_ID_2, &usData);
/* what does this achieve ? */
- MiRead(pAdapter, PHY_MPHY_CONTROL_REG, &usData); /* should read 0002 */
- MiWrite(pAdapter, PHY_MPHY_CONTROL_REG, 0x0006);
+ MiRead(etdev, PHY_MPHY_CONTROL_REG, &usData); /* should read 0002 */
+ MiWrite(etdev, PHY_MPHY_CONTROL_REG, 0x0006);
/* read modem register 0402, should I do something with
the return data? */
- MiWrite(pAdapter, PHY_INDEX_REG, 0x0402);
- MiRead(pAdapter, PHY_DATA_REG, &usData);
+ MiWrite(etdev, PHY_INDEX_REG, 0x0402);
+ MiRead(etdev, PHY_DATA_REG, &usData);
- MiWrite(pAdapter, PHY_MPHY_CONTROL_REG, 0x0002);
+ MiWrite(etdev, PHY_MPHY_CONTROL_REG, 0x0002);
/* what does this achieve (should return 0x1040) */
- MiRead(pAdapter, PHY_CONTROL, &usData);
- MiRead(pAdapter, PHY_MPHY_CONTROL_REG, &usData); /* should read 0002 */
- MiWrite(pAdapter, PHY_CONTROL, 0x1840);
+ MiRead(etdev, PHY_CONTROL, &usData);
+ MiRead(etdev, PHY_MPHY_CONTROL_REG, &usData); /* should read 0002 */
+ MiWrite(etdev, PHY_CONTROL, 0x1840);
- MiWrite(pAdapter, PHY_MPHY_CONTROL_REG, 0x0007);
+ MiWrite(etdev, PHY_MPHY_CONTROL_REG, 0x0007);
/* here the writing of the array starts.... */
usIndex = 0;
while (ConfigPhy[usIndex][0] != 0x0000) {
/* write value */
- MiWrite(pAdapter, PHY_INDEX_REG, ConfigPhy[usIndex][0]);
- MiWrite(pAdapter, PHY_DATA_REG, ConfigPhy[usIndex][1]);
+ MiWrite(etdev, PHY_INDEX_REG, ConfigPhy[usIndex][0]);
+ MiWrite(etdev, PHY_DATA_REG, ConfigPhy[usIndex][1]);
/* read it back */
- MiWrite(pAdapter, PHY_INDEX_REG, ConfigPhy[usIndex][0]);
- MiRead(pAdapter, PHY_DATA_REG, &usData);
+ MiWrite(etdev, PHY_INDEX_REG, ConfigPhy[usIndex][0]);
+ MiRead(etdev, PHY_DATA_REG, &usData);
/* do a check on the value read back ? */
usIndex++;
}
/* here the writing of the array ends... */
- MiRead(pAdapter, PHY_CONTROL, &usData); /* 0x1840 */
- MiRead(pAdapter, PHY_MPHY_CONTROL_REG, &usData);/* should read 0007 */
- MiWrite(pAdapter, PHY_CONTROL, 0x1040);
- MiWrite(pAdapter, PHY_MPHY_CONTROL_REG, 0x0002);
+ MiRead(etdev, PHY_CONTROL, &usData); /* 0x1840 */
+ MiRead(etdev, PHY_MPHY_CONTROL_REG, &usData);/* should read 0007 */
+ MiWrite(etdev, PHY_CONTROL, 0x1040);
+ MiWrite(etdev, PHY_MPHY_CONTROL_REG, 0x0002);
}
-void ET1310_PhyReset(struct et131x_adapter *pAdapter)
+void ET1310_PhyReset(struct et131x_adapter *etdev)
{
- MiWrite(pAdapter, PHY_CONTROL, 0x8000);
+ MiWrite(etdev, PHY_CONTROL, 0x8000);
}
-void ET1310_PhyPowerDown(struct et131x_adapter *pAdapter, bool down)
+void ET1310_PhyPowerDown(struct et131x_adapter *etdev, bool down)
{
uint16_t usData;
- MiRead(pAdapter, PHY_CONTROL, &usData);
+ MiRead(etdev, PHY_CONTROL, &usData);
if (down == false) {
/* Power UP */
usData &= ~0x0800;
- MiWrite(pAdapter, PHY_CONTROL, usData);
+ MiWrite(etdev, PHY_CONTROL, usData);
} else {
/* Power DOWN */
usData |= 0x0800;
- MiWrite(pAdapter, PHY_CONTROL, usData);
+ MiWrite(etdev, PHY_CONTROL, usData);
}
}
-void ET1310_PhyAutoNeg(struct et131x_adapter *pAdapter, bool enable)
+void ET1310_PhyAutoNeg(struct et131x_adapter *etdev, bool enable)
{
uint16_t usData;
- MiRead(pAdapter, PHY_CONTROL, &usData);
+ MiRead(etdev, PHY_CONTROL, &usData);
if (enable == true) {
/* Autonegotiation ON */
usData |= 0x1000;
- MiWrite(pAdapter, PHY_CONTROL, usData);
+ MiWrite(etdev, PHY_CONTROL, usData);
} else {
/* Autonegotiation OFF */
usData &= ~0x1000;
- MiWrite(pAdapter, PHY_CONTROL, usData);
+ MiWrite(etdev, PHY_CONTROL, usData);
}
}
-void ET1310_PhyDuplexMode(struct et131x_adapter *pAdapter, uint16_t duplex)
+void ET1310_PhyDuplexMode(struct et131x_adapter *etdev, uint16_t duplex)
{
uint16_t usData;
- MiRead(pAdapter, PHY_CONTROL, &usData);
+ MiRead(etdev, PHY_CONTROL, &usData);
if (duplex == TRUEPHY_DUPLEX_FULL) {
/* Set Full Duplex */
usData |= 0x100;
- MiWrite(pAdapter, PHY_CONTROL, usData);
+ MiWrite(etdev, PHY_CONTROL, usData);
} else {
/* Set Half Duplex */
usData &= ~0x100;
- MiWrite(pAdapter, PHY_CONTROL, usData);
+ MiWrite(etdev, PHY_CONTROL, usData);
}
}
-void ET1310_PhySpeedSelect(struct et131x_adapter *pAdapter, uint16_t speed)
+void ET1310_PhySpeedSelect(struct et131x_adapter *etdev, uint16_t speed)
{
uint16_t usData;
/* Read the PHY control register */
- MiRead(pAdapter, PHY_CONTROL, &usData);
+ MiRead(etdev, PHY_CONTROL, &usData);
/* Clear all Speed settings (Bits 6, 13) */
usData &= ~0x2040;
}
/* Write back the new speed */
- MiWrite(pAdapter, PHY_CONTROL, usData);
+ MiWrite(etdev, PHY_CONTROL, usData);
}
-void ET1310_PhyAdvertise1000BaseT(struct et131x_adapter *pAdapter,
+void ET1310_PhyAdvertise1000BaseT(struct et131x_adapter *etdev,
uint16_t duplex)
{
uint16_t usData;
/* Read the PHY 1000 Base-T Control Register */
- MiRead(pAdapter, PHY_1000_CONTROL, &usData);
+ MiRead(etdev, PHY_1000_CONTROL, &usData);
/* Clear Bits 8,9 */
usData &= ~0x0300;
}
/* Write back advertisement */
- MiWrite(pAdapter, PHY_1000_CONTROL, usData);
+ MiWrite(etdev, PHY_1000_CONTROL, usData);
}
-void ET1310_PhyAdvertise100BaseT(struct et131x_adapter *pAdapter,
+void ET1310_PhyAdvertise100BaseT(struct et131x_adapter *etdev,
uint16_t duplex)
{
uint16_t usData;
/* Read the Autonegotiation Register (10/100) */
- MiRead(pAdapter, PHY_AUTO_ADVERTISEMENT, &usData);
+ MiRead(etdev, PHY_AUTO_ADVERTISEMENT, &usData);
/* Clear bits 7,8 */
usData &= ~0x0180;
}
/* Write back advertisement */
- MiWrite(pAdapter, PHY_AUTO_ADVERTISEMENT, usData);
+ MiWrite(etdev, PHY_AUTO_ADVERTISEMENT, usData);
}
-void ET1310_PhyAdvertise10BaseT(struct et131x_adapter *pAdapter,
+void ET1310_PhyAdvertise10BaseT(struct et131x_adapter *etdev,
uint16_t duplex)
{
uint16_t usData;
/* Read the Autonegotiation Register (10/100) */
- MiRead(pAdapter, PHY_AUTO_ADVERTISEMENT, &usData);
+ MiRead(etdev, PHY_AUTO_ADVERTISEMENT, &usData);
/* Clear bits 5,6 */
usData &= ~0x0060;
}
/* Write back advertisement */
- MiWrite(pAdapter, PHY_AUTO_ADVERTISEMENT, usData);
+ MiWrite(etdev, PHY_AUTO_ADVERTISEMENT, usData);
}
-void ET1310_PhyLinkStatus(struct et131x_adapter *pAdapter,
+void ET1310_PhyLinkStatus(struct et131x_adapter *etdev,
uint8_t *ucLinkStatus,
uint32_t *uiAutoNeg,
uint32_t *uiLinkSpeed,
uint16_t usVmiPhyStatus = 0;
uint16_t usControl = 0;
- MiRead(pAdapter, PHY_STATUS, &usMiStatus);
- MiRead(pAdapter, PHY_1000_STATUS, &us1000BaseT);
- MiRead(pAdapter, PHY_PHY_STATUS, &usVmiPhyStatus);
- MiRead(pAdapter, PHY_CONTROL, &usControl);
+ MiRead(etdev, PHY_STATUS, &usMiStatus);
+ MiRead(etdev, PHY_1000_STATUS, &us1000BaseT);
+ MiRead(etdev, PHY_PHY_STATUS, &usVmiPhyStatus);
+ MiRead(etdev, PHY_CONTROL, &usControl);
if (ucLinkStatus) {
*ucLinkStatus =
}
}
-void ET1310_PhyAndOrReg(struct et131x_adapter *pAdapter,
+void ET1310_PhyAndOrReg(struct et131x_adapter *etdev,
uint16_t regnum, uint16_t andMask, uint16_t orMask)
{
uint16_t reg;
/* Read the requested register */
- MiRead(pAdapter, regnum, ®);
+ MiRead(etdev, regnum, ®);
/* Apply the AND mask */
reg &= andMask;
reg |= orMask;
/* Write the value back to the register */
- MiWrite(pAdapter, regnum, reg);
+ MiWrite(etdev, regnum, reg);
}
-void ET1310_PhyAccessMiBit(struct et131x_adapter *pAdapter, uint16_t action,
+void ET1310_PhyAccessMiBit(struct et131x_adapter *etdev, uint16_t action,
uint16_t regnum, uint16_t bitnum, uint8_t *value)
{
uint16_t reg;
mask = 0x0001 << bitnum;
/* Read the requested register */
- MiRead(pAdapter, regnum, ®);
+ MiRead(etdev, regnum, ®);
switch (action) {
case TRUEPHY_BIT_READ:
case TRUEPHY_BIT_SET:
reg |= mask;
- MiWrite(pAdapter, regnum, reg);
+ MiWrite(etdev, regnum, reg);
break;
case TRUEPHY_BIT_CLEAR:
reg &= ~mask;
- MiWrite(pAdapter, regnum, reg);
+ MiWrite(etdev, regnum, reg);
break;
default:
/**
* EnablePhyComa - called when network cable is unplugged
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*
* driver receive an phy status change interrupt while in D0 and check that
* phy_status is down.
* indicating linkup status, call the MPDisablePhyComa routine to
* restore JAGCore and gigE PHY
*/
-void EnablePhyComa(struct et131x_adapter *pAdapter)
+void EnablePhyComa(struct et131x_adapter *etdev)
{
unsigned long lockflags;
PM_CSR_t GlobalPmCSR;
DBG_ENTER(et131x_dbginfo);
- GlobalPmCSR.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
+ GlobalPmCSR.value = readl(&etdev->CSRAddress->global.pm_csr.value);
/* Save the GbE PHY speed and duplex modes. Need to restore this
* when cable is plugged back in
*/
- pAdapter->PoMgmt.PowerDownSpeed = pAdapter->AiForceSpeed;
- pAdapter->PoMgmt.PowerDownDuplex = pAdapter->AiForceDpx;
+ etdev->PoMgmt.PowerDownSpeed = etdev->AiForceSpeed;
+ etdev->PoMgmt.PowerDownDuplex = etdev->AiForceDpx;
/* Stop sending packets. */
- spin_lock_irqsave(&pAdapter->SendHWLock, lockflags);
- MP_SET_FLAG(pAdapter, fMP_ADAPTER_LOWER_POWER);
- spin_unlock_irqrestore(&pAdapter->SendHWLock, lockflags);
+ spin_lock_irqsave(&etdev->SendHWLock, lockflags);
+ MP_SET_FLAG(etdev, fMP_ADAPTER_LOWER_POWER);
+ spin_unlock_irqrestore(&etdev->SendHWLock, lockflags);
/* Wait for outstanding Receive packets */
- while ((MP_GET_RCV_REF(pAdapter) != 0) && (LoopCounter-- > 0))
+ while ((MP_GET_RCV_REF(etdev) != 0) && (LoopCounter-- > 0))
mdelay(2);
/* Gate off JAGCore 3 clock domains */
GlobalPmCSR.bits.pm_sysclk_gate = 0;
GlobalPmCSR.bits.pm_txclk_gate = 0;
GlobalPmCSR.bits.pm_rxclk_gate = 0;
- writel(GlobalPmCSR.value, &pAdapter->CSRAddress->global.pm_csr.value);
+ writel(GlobalPmCSR.value, &etdev->CSRAddress->global.pm_csr.value);
/* Program gigE PHY in to Coma mode */
GlobalPmCSR.bits.pm_phy_sw_coma = 1;
- writel(GlobalPmCSR.value, &pAdapter->CSRAddress->global.pm_csr.value);
+ writel(GlobalPmCSR.value, &etdev->CSRAddress->global.pm_csr.value);
DBG_LEAVE(et131x_dbginfo);
}
/**
* DisablePhyComa - Disable the Phy Coma Mode
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void DisablePhyComa(struct et131x_adapter *pAdapter)
+void DisablePhyComa(struct et131x_adapter *etdev)
{
PM_CSR_t GlobalPmCSR;
DBG_ENTER(et131x_dbginfo);
- GlobalPmCSR.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
+ GlobalPmCSR.value = readl(&etdev->CSRAddress->global.pm_csr.value);
/* Disable phy_sw_coma register and re-enable JAGCore clocks */
GlobalPmCSR.bits.pm_sysclk_gate = 1;
GlobalPmCSR.bits.pm_txclk_gate = 1;
GlobalPmCSR.bits.pm_rxclk_gate = 1;
GlobalPmCSR.bits.pm_phy_sw_coma = 0;
- writel(GlobalPmCSR.value, &pAdapter->CSRAddress->global.pm_csr.value);
+ writel(GlobalPmCSR.value, &etdev->CSRAddress->global.pm_csr.value);
/* Restore the GbE PHY speed and duplex modes;
* Reset JAGCore; re-configure and initialize JAGCore and gigE PHY
*/
- pAdapter->AiForceSpeed = pAdapter->PoMgmt.PowerDownSpeed;
- pAdapter->AiForceDpx = pAdapter->PoMgmt.PowerDownDuplex;
+ etdev->AiForceSpeed = etdev->PoMgmt.PowerDownSpeed;
+ etdev->AiForceDpx = etdev->PoMgmt.PowerDownDuplex;
/* Re-initialize the send structures */
- et131x_init_send(pAdapter);
+ et131x_init_send(etdev);
/* Reset the RFD list and re-start RU */
- et131x_reset_recv(pAdapter);
+ et131x_reset_recv(etdev);
/* Bring the device back to the state it was during init prior to
* autonegotiation being complete. This way, when we get the auto-neg
* complete interrupt, we can complete init by calling ConfigMacREGS2.
*/
- et131x_soft_reset(pAdapter);
+ et131x_soft_reset(etdev);
/* setup et1310 as per the documentation ?? */
- et131x_adapter_setup(pAdapter);
+ et131x_adapter_setup(etdev);
/* Allow Tx to restart */
- MP_CLEAR_FLAG(pAdapter, fMP_ADAPTER_LOWER_POWER);
+ MP_CLEAR_FLAG(etdev, fMP_ADAPTER_LOWER_POWER);
/* Need to re-enable Rx. */
- et131x_rx_dma_enable(pAdapter);
+ et131x_rx_dma_enable(etdev);
DBG_LEAVE(et131x_dbginfo);
}
#endif /* CONFIG_ET131X_DEBUG */
-void nic_return_rfd(struct et131x_adapter *pAdapter, PMP_RFD pMpRfd);
+void nic_return_rfd(struct et131x_adapter *etdev, PMP_RFD pMpRfd);
/**
* et131x_rx_dma_memory_alloc
/**
* ConfigRxDmaRegs - Start of Rx_DMA init sequence
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void ConfigRxDmaRegs(struct et131x_adapter *pAdapter)
+void ConfigRxDmaRegs(struct et131x_adapter *etdev)
{
- struct _RXDMA_t __iomem *pRxDma = &pAdapter->CSRAddress->rxdma;
- struct _rx_ring_t *pRxLocal = &pAdapter->RxRing;
+ struct _RXDMA_t __iomem *pRxDma = &etdev->CSRAddress->rxdma;
+ struct _rx_ring_t *pRxLocal = &etdev->RxRing;
PFBR_DESC_t pFbrEntry;
uint32_t iEntry;
RXDMA_PSR_NUM_DES_t psr_num_des;
DBG_ENTER(et131x_dbginfo);
/* Halt RXDMA to perform the reconfigure. */
- et131x_rx_dma_disable(pAdapter);
+ et131x_rx_dma_disable(etdev);
/* Load the completion writeback physical address
*
writel((psr_num_des.bits.psr_ndes * LO_MARK_PERCENT_FOR_PSR) / 100,
&pRxDma->psr_min_des.value);
- spin_lock_irqsave(&pAdapter->RcvLock, lockflags);
+ spin_lock_irqsave(&etdev->RcvLock, lockflags);
/* These local variables track the PSR in the adapter structure */
pRxLocal->local_psr_full.bits.psr_full = 0;
* For version B silicon, this value gets updated once autoneg is
*complete.
*/
- writel(pAdapter->RegistryRxNumBuffers, &pRxDma->num_pkt_done.value);
+ writel(etdev->RegistryRxNumBuffers, &pRxDma->num_pkt_done.value);
/* The "time_done" is not working correctly to coalesce interrupts
* after a given time period, but rather is giving us an interrupt
* regardless of whether we have received packets.
* This value gets updated once autoneg is complete.
*/
- writel(pAdapter->RegistryRxTimeInterval, &pRxDma->max_pkt_time.value);
+ writel(etdev->RegistryRxTimeInterval, &pRxDma->max_pkt_time.value);
- spin_unlock_irqrestore(&pAdapter->RcvLock, lockflags);
+ spin_unlock_irqrestore(&etdev->RcvLock, lockflags);
DBG_LEAVE(et131x_dbginfo);
}
/**
* SetRxDmaTimer - Set the heartbeat timer according to line rate.
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void SetRxDmaTimer(struct et131x_adapter *pAdapter)
+void SetRxDmaTimer(struct et131x_adapter *etdev)
{
/* For version B silicon, we do not use the RxDMA timer for 10 and 100
* Mbits/s line rates. We do not enable and RxDMA interrupt coalescing.
*/
- if ((pAdapter->uiLinkSpeed == TRUEPHY_SPEED_100MBPS) ||
- (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_10MBPS)) {
- writel(0, &pAdapter->CSRAddress->rxdma.max_pkt_time.value);
- writel(1, &pAdapter->CSRAddress->rxdma.num_pkt_done.value);
+ if ((etdev->uiLinkSpeed == TRUEPHY_SPEED_100MBPS) ||
+ (etdev->uiLinkSpeed == TRUEPHY_SPEED_10MBPS)) {
+ writel(0, &etdev->CSRAddress->rxdma.max_pkt_time.value);
+ writel(1, &etdev->CSRAddress->rxdma.num_pkt_done.value);
}
}
/**
* et131x_rx_dma_disable - Stop of Rx_DMA on the ET1310
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void et131x_rx_dma_disable(struct et131x_adapter *pAdapter)
+void et131x_rx_dma_disable(struct et131x_adapter *etdev)
{
RXDMA_CSR_t csr;
DBG_ENTER(et131x_dbginfo);
/* Setup the receive dma configuration register */
- writel(0x00002001, &pAdapter->CSRAddress->rxdma.csr.value);
- csr.value = readl(&pAdapter->CSRAddress->rxdma.csr.value);
+ writel(0x00002001, &etdev->CSRAddress->rxdma.csr.value);
+ csr.value = readl(&etdev->CSRAddress->rxdma.csr.value);
if (csr.bits.halt_status != 1) {
udelay(5);
- csr.value = readl(&pAdapter->CSRAddress->rxdma.csr.value);
+ csr.value = readl(&etdev->CSRAddress->rxdma.csr.value);
if (csr.bits.halt_status != 1)
DBG_ERROR(et131x_dbginfo,
"RX Dma failed to enter halt state. CSR 0x%08x\n",
/**
* et131x_rx_dma_enable - re-start of Rx_DMA on the ET1310.
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void et131x_rx_dma_enable(struct et131x_adapter *pAdapter)
+void et131x_rx_dma_enable(struct et131x_adapter *etdev)
{
DBG_RX_ENTER(et131x_dbginfo);
- if (pAdapter->RegistryPhyLoopbk)
+ if (etdev->RegistryPhyLoopbk)
/* RxDMA is disabled for loopback operation. */
- writel(0x1, &pAdapter->CSRAddress->rxdma.csr.value);
+ writel(0x1, &etdev->CSRAddress->rxdma.csr.value);
else {
/* Setup the receive dma configuration register for normal operation */
RXDMA_CSR_t csr = { 0 };
csr.bits.fbr1_enable = 1;
- if (pAdapter->RxRing.Fbr1BufferSize == 4096)
+ if (etdev->RxRing.Fbr1BufferSize == 4096)
csr.bits.fbr1_size = 1;
- else if (pAdapter->RxRing.Fbr1BufferSize == 8192)
+ else if (etdev->RxRing.Fbr1BufferSize == 8192)
csr.bits.fbr1_size = 2;
- else if (pAdapter->RxRing.Fbr1BufferSize == 16384)
+ else if (etdev->RxRing.Fbr1BufferSize == 16384)
csr.bits.fbr1_size = 3;
#ifdef USE_FBR0
csr.bits.fbr0_enable = 1;
- if (pAdapter->RxRing.Fbr0BufferSize == 256)
+ if (etdev->RxRing.Fbr0BufferSize == 256)
csr.bits.fbr0_size = 1;
- else if (pAdapter->RxRing.Fbr0BufferSize == 512)
+ else if (etdev->RxRing.Fbr0BufferSize == 512)
csr.bits.fbr0_size = 2;
- else if (pAdapter->RxRing.Fbr0BufferSize == 1024)
+ else if (etdev->RxRing.Fbr0BufferSize == 1024)
csr.bits.fbr0_size = 3;
#endif
- writel(csr.value, &pAdapter->CSRAddress->rxdma.csr.value);
+ writel(csr.value, &etdev->CSRAddress->rxdma.csr.value);
- csr.value = readl(&pAdapter->CSRAddress->rxdma.csr.value);
+ csr.value = readl(&etdev->CSRAddress->rxdma.csr.value);
if (csr.bits.halt_status != 0) {
udelay(5);
- csr.value = readl(&pAdapter->CSRAddress->rxdma.csr.value);
+ csr.value = readl(&etdev->CSRAddress->rxdma.csr.value);
if (csr.bits.halt_status != 0) {
DBG_ERROR(et131x_dbginfo,
"RX Dma failed to exit halt state. CSR 0x%08x\n",
/**
* nic_rx_pkts - Checks the hardware for available packets
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Returns pMpRfd, a pointer to our MPRFD.
*
* the packet to it, puts the RFD in the RecvPendList, and also returns
* the pointer to the RFD.
*/
-PMP_RFD nic_rx_pkts(struct et131x_adapter *pAdapter)
+PMP_RFD nic_rx_pkts(struct et131x_adapter *etdev)
{
- struct _rx_ring_t *pRxLocal = &pAdapter->RxRing;
+ struct _rx_ring_t *pRxLocal = &etdev->RxRing;
PRX_STATUS_BLOCK_t pRxStatusBlock;
PPKT_STAT_DESC_t pPSREntry;
PMP_RFD pMpRfd;
}
writel(pRxLocal->local_psr_full.value,
- &pAdapter->CSRAddress->rxdma.psr_full_offset.value);
+ &etdev->CSRAddress->rxdma.psr_full_offset.value);
#ifndef USE_FBR0
if (ringIndex != 1) {
}
/* Get and fill the RFD. */
- spin_lock_irqsave(&pAdapter->RcvLock, lockflags);
+ spin_lock_irqsave(&etdev->RcvLock, lockflags);
pMpRfd = NULL;
element = pRxLocal->RecvList.next;
DBG_RX(et131x_dbginfo,
"NULL RFD returned from RecvList via list_entry()\n");
DBG_RX_LEAVE(et131x_dbginfo);
- spin_unlock_irqrestore(&pAdapter->RcvLock, lockflags);
+ spin_unlock_irqrestore(&etdev->RcvLock, lockflags);
return NULL;
}
list_del(&pMpRfd->list_node);
pRxLocal->nReadyRecv--;
- spin_unlock_irqrestore(&pAdapter->RcvLock, lockflags);
+ spin_unlock_irqrestore(&etdev->RcvLock, lockflags);
pMpRfd->iBufferIndex = bufferIndex;
pMpRfd->iRingIndex = ringIndex;
* also counted here.
*/
if (localLen < (NIC_MIN_PACKET_SIZE + 4)) {
- pAdapter->Stats.other_errors++;
+ etdev->Stats.other_errors++;
localLen = 0;
}
if (localLen) {
- if (pAdapter->ReplicaPhyLoopbk == 1) {
+ if (etdev->ReplicaPhyLoopbk == 1) {
pBufVa = pRxLocal->Fbr[ringIndex]->Va[bufferIndex];
- if (memcmp(&pBufVa[6], &pAdapter->CurrentAddress[0],
+ if (memcmp(&pBufVa[6], &etdev->CurrentAddress[0],
ETH_ALEN) == 0) {
if (memcmp(&pBufVa[42], "Replica packet",
ETH_HLEN)) {
- pAdapter->ReplicaPhyLoopbkPF = 1;
+ etdev->ReplicaPhyLoopbkPF = 1;
}
}
DBG_WARNING(et131x_dbginfo,
DBG_WARNING(et131x_dbginfo,
"CurrentAddr:\t%02x:%02x:%02x:%02x:%02x:%02x\n",
- pAdapter->CurrentAddress[0],
- pAdapter->CurrentAddress[1],
- pAdapter->CurrentAddress[2],
- pAdapter->CurrentAddress[3],
- pAdapter->CurrentAddress[4],
- pAdapter->CurrentAddress[5]);
+ etdev->CurrentAddress[0],
+ etdev->CurrentAddress[1],
+ etdev->CurrentAddress[2],
+ etdev->CurrentAddress[3],
+ etdev->CurrentAddress[4],
+ etdev->CurrentAddress[5]);
}
/* Determine if this is a multicast packet coming in */
* filters. Generally filter is 0x2b when in
* promiscuous mode.
*/
- if ((pAdapter->PacketFilter & ET131X_PACKET_TYPE_MULTICAST)
- && !(pAdapter->PacketFilter & ET131X_PACKET_TYPE_PROMISCUOUS)
- && !(pAdapter->PacketFilter & ET131X_PACKET_TYPE_ALL_MULTICAST)) {
+ if ((etdev->PacketFilter & ET131X_PACKET_TYPE_MULTICAST)
+ && !(etdev->PacketFilter & ET131X_PACKET_TYPE_PROMISCUOUS)
+ && !(etdev->PacketFilter & ET131X_PACKET_TYPE_ALL_MULTICAST)) {
pBufVa = pRxLocal->Fbr[ringIndex]->
Va[bufferIndex];
* matches one in our list.
*/
for (nIndex = 0;
- nIndex < pAdapter->MCAddressCount;
+ nIndex < etdev->MCAddressCount;
nIndex++) {
if (pBufVa[0] ==
- pAdapter->MCList[nIndex][0]
+ etdev->MCList[nIndex][0]
&& pBufVa[1] ==
- pAdapter->MCList[nIndex][1]
+ etdev->MCList[nIndex][1]
&& pBufVa[2] ==
- pAdapter->MCList[nIndex][2]
+ etdev->MCList[nIndex][2]
&& pBufVa[3] ==
- pAdapter->MCList[nIndex][3]
+ etdev->MCList[nIndex][3]
&& pBufVa[4] ==
- pAdapter->MCList[nIndex][4]
+ etdev->MCList[nIndex][4]
&& pBufVa[5] ==
- pAdapter->MCList[nIndex][5]) {
+ etdev->MCList[nIndex][5]) {
break;
}
}
* so we free our RFD when we return
* from this function.
*/
- if (nIndex == pAdapter->MCAddressCount)
+ if (nIndex == etdev->MCAddressCount)
localLen = 0;
}
if (localLen > 0)
- pAdapter->Stats.multircv++;
+ etdev->Stats.multircv++;
} else if (Word0.value & ALCATEL_BROADCAST_PKT)
- pAdapter->Stats.brdcstrcv++;
+ etdev->Stats.brdcstrcv++;
else
/* Not sure what this counter measures in
* promiscuous mode. Perhaps we should check
* the MAC address to see if it is directed
* to us in promiscuous mode.
*/
- pAdapter->Stats.unircv++;
+ etdev->Stats.unircv++;
}
if (localLen > 0) {
return NULL;
}
- pAdapter->net_stats.rx_bytes += pMpRfd->PacketSize;
+ etdev->net_stats.rx_bytes += pMpRfd->PacketSize;
memcpy(skb_put(skb, pMpRfd->PacketSize),
pRxLocal->Fbr[ringIndex]->Va[bufferIndex],
pMpRfd->PacketSize);
- skb->dev = pAdapter->netdev;
- skb->protocol = eth_type_trans(skb, pAdapter->netdev);
+ skb->dev = etdev->netdev;
+ skb->protocol = eth_type_trans(skb, etdev->netdev);
skb->ip_summed = CHECKSUM_NONE;
netif_rx(skb);
pMpRfd->PacketSize = 0;
}
- nic_return_rfd(pAdapter, pMpRfd);
+ nic_return_rfd(etdev, pMpRfd);
DBG_RX(et131x_dbginfo, "(1)\n");
DBG_RX_LEAVE(et131x_dbginfo);
/**
* et131x_reset_recv - Reset the receive list
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Assumption, Rcv spinlock has been acquired.
*/
-void et131x_reset_recv(struct et131x_adapter *pAdapter)
+void et131x_reset_recv(struct et131x_adapter *etdev)
{
PMP_RFD pMpRfd;
struct list_head *element;
DBG_ENTER(et131x_dbginfo);
- DBG_ASSERT(!list_empty(&pAdapter->RxRing.RecvList));
+ DBG_ASSERT(!list_empty(&etdev->RxRing.RecvList));
/* Take all the RFD's from the pending list, and stick them on the
* RecvList.
*/
- while (!list_empty(&pAdapter->RxRing.RecvPendingList)) {
- element = pAdapter->RxRing.RecvPendingList.next;
+ while (!list_empty(&etdev->RxRing.RecvPendingList)) {
+ element = etdev->RxRing.RecvPendingList.next;
pMpRfd = (PMP_RFD) list_entry(element, MP_RFD, list_node);
- list_move_tail(&pMpRfd->list_node, &pAdapter->RxRing.RecvList);
+ list_move_tail(&pMpRfd->list_node, &etdev->RxRing.RecvList);
}
DBG_LEAVE(et131x_dbginfo);
/**
* et131x_handle_recv_interrupt - Interrupt handler for receive processing
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Assumption, Rcv spinlock has been acquired.
*/
-void et131x_handle_recv_interrupt(struct et131x_adapter *pAdapter)
+void et131x_handle_recv_interrupt(struct et131x_adapter *etdev)
{
PMP_RFD pMpRfd = NULL;
struct sk_buff *PacketArray[NUM_PACKETS_HANDLED];
/* Process up to available RFD's */
while (PacketArrayCount < PacketsToHandle) {
- if (list_empty(&pAdapter->RxRing.RecvList)) {
- DBG_ASSERT(pAdapter->RxRing.nReadyRecv == 0);
+ if (list_empty(&etdev->RxRing.RecvList)) {
+ DBG_ASSERT(etdev->RxRing.nReadyRecv == 0);
DBG_ERROR(et131x_dbginfo, "NO RFD's !!!!!!!!!!!!!\n");
TempUnfinishedRec = true;
break;
}
- pMpRfd = nic_rx_pkts(pAdapter);
+ pMpRfd = nic_rx_pkts(etdev);
if (pMpRfd == NULL)
break;
* If length is zero, return the RFD in order to advance the
* Free buffer ring.
*/
- if ((!pAdapter->PacketFilter) ||
- (pAdapter->PoMgmt.PowerState != NdisDeviceStateD0) ||
- (!MP_LINK_DETECTED(pAdapter)) ||
+ if ((!etdev->PacketFilter) ||
+ (etdev->PoMgmt.PowerState != NdisDeviceStateD0) ||
+ (!MP_LINK_DETECTED(etdev)) ||
(pMpRfd->PacketSize == 0)) {
continue;
}
/* Increment the number of packets we received */
- pAdapter->Stats.ipackets++;
+ etdev->Stats.ipackets++;
/* Set the status on the packet, either resources or success */
- if (pAdapter->RxRing.nReadyRecv >= RFD_LOW_WATER_MARK) {
+ if (etdev->RxRing.nReadyRecv >= RFD_LOW_WATER_MARK) {
/* Put this RFD on the pending list
*
* NOTE: nic_rx_pkts() above is already returning the
* Besides, we don't really need (at this point) the
* pending list anyway.
*/
- /* spin_lock_irqsave( &pAdapter->RcvPendLock, lockflags );
- * list_add_tail( &pMpRfd->list_node, &pAdapter->RxRing.RecvPendingList );
- * spin_unlock_irqrestore( &pAdapter->RcvPendLock, lockflags );
+ /* spin_lock_irqsave( &etdev->RcvPendLock, lockflags );
+ * list_add_tail( &pMpRfd->list_node, &etdev->RxRing.RecvPendingList );
+ * spin_unlock_irqrestore( &etdev->RcvPendLock, lockflags );
*/
/* Update the number of outstanding Recvs */
- /* MP_INC_RCV_REF( pAdapter ); */
+ /* MP_INC_RCV_REF( etdev ); */
} else {
RFDFreeArray[PacketFreeCount] = pMpRfd;
PacketFreeCount++;
}
if ((PacketArrayCount == NUM_PACKETS_HANDLED) || TempUnfinishedRec) {
- pAdapter->RxRing.UnfinishedReceives = true;
- writel(pAdapter->RegistryTxTimeInterval * NANO_IN_A_MICRO,
- &pAdapter->CSRAddress->global.watchdog_timer);
+ etdev->RxRing.UnfinishedReceives = true;
+ writel(etdev->RegistryTxTimeInterval * NANO_IN_A_MICRO,
+ &etdev->CSRAddress->global.watchdog_timer);
} else {
/* Watchdog timer will disable itself if appropriate. */
- pAdapter->RxRing.UnfinishedReceives = false;
+ etdev->RxRing.UnfinishedReceives = false;
}
DBG_RX_LEAVE(et131x_dbginfo);
/**
* NICReturnRFD - Recycle a RFD and put it back onto the receive list
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
* @pMpRfd: pointer to the RFD
*/
-void nic_return_rfd(struct et131x_adapter *pAdapter, PMP_RFD pMpRfd)
+void nic_return_rfd(struct et131x_adapter *etdev, PMP_RFD pMpRfd)
{
- struct _rx_ring_t *pRxLocal = &pAdapter->RxRing;
- struct _RXDMA_t __iomem *pRxDma = &pAdapter->CSRAddress->rxdma;
+ struct _rx_ring_t *pRxLocal = &etdev->RxRing;
+ struct _RXDMA_t __iomem *pRxDma = &etdev->CSRAddress->rxdma;
uint16_t bi = pMpRfd->iBufferIndex;
uint8_t ri = pMpRfd->iRingIndex;
unsigned long lockflags;
(ri == 0 && bi < pRxLocal->Fbr0NumEntries) ||
#endif
(ri == 1 && bi < pRxLocal->Fbr1NumEntries)) {
- spin_lock_irqsave(&pAdapter->FbrLock, lockflags);
+ spin_lock_irqsave(&etdev->FbrLock, lockflags);
if (ri == 1) {
PFBR_DESC_t pNextDesc =
&pRxDma->fbr0_full_offset.value);
}
#endif
- spin_unlock_irqrestore(&pAdapter->FbrLock, lockflags);
+ spin_unlock_irqrestore(&etdev->FbrLock, lockflags);
} else {
DBG_ERROR(et131x_dbginfo,
"NICReturnRFD illegal Buffer Index returned\n");
/* The processing on this RFD is done, so put it back on the tail of
* our list
*/
- spin_lock_irqsave(&pAdapter->RcvLock, lockflags);
+ spin_lock_irqsave(&etdev->RcvLock, lockflags);
list_add_tail(&pMpRfd->list_node, &pRxLocal->RecvList);
pRxLocal->nReadyRecv++;
- spin_unlock_irqrestore(&pAdapter->RcvLock, lockflags);
+ spin_unlock_irqrestore(&etdev->RcvLock, lockflags);
DBG_ASSERT(pRxLocal->nReadyRecv <= pRxLocal->NumRfd);
DBG_RX_LEAVE(et131x_dbginfo);
extern dbg_info_t *et131x_dbginfo;
#endif /* CONFIG_ET131X_DEBUG */
-static void et131x_update_tcb_list(struct et131x_adapter *pAdapter);
-static void et131x_check_send_wait_list(struct et131x_adapter *pAdapter);
-static inline void et131x_free_send_packet(struct et131x_adapter *pAdapter,
+static void et131x_update_tcb_list(struct et131x_adapter *etdev);
+static void et131x_check_send_wait_list(struct et131x_adapter *etdev);
+static inline void et131x_free_send_packet(struct et131x_adapter *etdev,
PMP_TCB pMpTcb);
static int et131x_send_packet(struct sk_buff *skb,
- struct et131x_adapter *pAdapter);
-static int nic_send_packet(struct et131x_adapter *pAdapter, PMP_TCB pMpTcb);
+ struct et131x_adapter *etdev);
+static int nic_send_packet(struct et131x_adapter *etdev, PMP_TCB pMpTcb);
/**
* et131x_tx_dma_memory_alloc
* ConfigTxDmaRegs - Set up the tx dma section of the JAGCore.
* @adapter: pointer to our private adapter structure
*/
-void ConfigTxDmaRegs(struct et131x_adapter *pAdapter)
+void ConfigTxDmaRegs(struct et131x_adapter *etdev)
{
- struct _TXDMA_t __iomem *pTxDma = &pAdapter->CSRAddress->txdma;
+ struct _TXDMA_t __iomem *pTxDma = &etdev->CSRAddress->txdma;
DBG_ENTER(et131x_dbginfo);
/* Load the hardware with the start of the transmit descriptor ring. */
- writel((uint32_t) (pAdapter->TxRing.pTxDescRingAdjustedPa >> 32),
+ writel((uint32_t) (etdev->TxRing.pTxDescRingAdjustedPa >> 32),
&pTxDma->pr_base_hi);
- writel((uint32_t) pAdapter->TxRing.pTxDescRingAdjustedPa,
+ writel((uint32_t) etdev->TxRing.pTxDescRingAdjustedPa,
&pTxDma->pr_base_lo);
/* Initialise the transmit DMA engine */
* storing the adjusted address.
*/
writel(0, &pTxDma->dma_wb_base_hi);
- writel(pAdapter->TxRing.pTxStatusPa, &pTxDma->dma_wb_base_lo);
+ writel(etdev->TxRing.pTxStatusPa, &pTxDma->dma_wb_base_lo);
- memset(pAdapter->TxRing.pTxStatusVa, 0, sizeof(TX_STATUS_BLOCK_t));
+ memset(etdev->TxRing.pTxStatusVa, 0, sizeof(TX_STATUS_BLOCK_t));
writel(0, &pTxDma->service_request.value);
- pAdapter->TxRing.txDmaReadyToSend.value = 0;
+ etdev->TxRing.txDmaReadyToSend.value = 0;
DBG_LEAVE(et131x_dbginfo);
}
/**
* et131x_tx_dma_disable - Stop of Tx_DMA on the ET1310
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void et131x_tx_dma_disable(struct et131x_adapter *pAdapter)
+void et131x_tx_dma_disable(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
/* Setup the tramsmit dma configuration register */
- writel(0x101, &pAdapter->CSRAddress->txdma.csr.value);
+ writel(0x101, &etdev->CSRAddress->txdma.csr.value);
DBG_LEAVE(et131x_dbginfo);
}
/**
* et131x_tx_dma_enable - re-start of Tx_DMA on the ET1310.
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*
* Mainly used after a return to the D0 (full-power) state from a lower state.
*/
-void et131x_tx_dma_enable(struct et131x_adapter *pAdapter)
+void et131x_tx_dma_enable(struct et131x_adapter *etdev)
{
DBG_ENTER(et131x_dbginfo);
- if (pAdapter->RegistryPhyLoopbk) {
+ if (etdev->RegistryPhyLoopbk) {
/* TxDMA is disabled for loopback operation. */
- writel(0x101, &pAdapter->CSRAddress->txdma.csr.value);
+ writel(0x101, &etdev->CSRAddress->txdma.csr.value);
} else {
TXDMA_CSR_t csr = { 0 };
*/
csr.bits.sngl_epkt_mode = 1;
csr.bits.halt = 0;
- csr.bits.cache_thrshld = pAdapter->RegistryDMACache;
- writel(csr.value, &pAdapter->CSRAddress->txdma.csr.value);
+ csr.bits.cache_thrshld = etdev->RegistryDMACache;
+ writel(csr.value, &etdev->CSRAddress->txdma.csr.value);
}
DBG_LEAVE(et131x_dbginfo);
int et131x_send_packets(struct sk_buff *skb, struct net_device *netdev)
{
int status = 0;
- struct et131x_adapter *pAdapter = NULL;
+ struct et131x_adapter *etdev = NULL;
DBG_TX_ENTER(et131x_dbginfo);
- pAdapter = netdev_priv(netdev);
+ etdev = netdev_priv(netdev);
/* Send these packets
*
*/
/* Queue is not empty or TCB is not available */
- if (!list_empty(&pAdapter->TxRing.SendWaitQueue) ||
- MP_TCB_RESOURCES_NOT_AVAILABLE(pAdapter)) {
+ if (!list_empty(&etdev->TxRing.SendWaitQueue) ||
+ MP_TCB_RESOURCES_NOT_AVAILABLE(etdev)) {
/* NOTE: If there's an error on send, no need to queue the
* packet under Linux; if we just send an error up to the
* netif layer, it will resend the skb to us.
* netif layer think we're good and drop the packet
*/
/*
- * if( MP_SHOULD_FAIL_SEND( pAdapter ) ||
- * pAdapter->DriverNoPhyAccess )
+ * if( MP_SHOULD_FAIL_SEND( etdev ) ||
+ * etdev->DriverNoPhyAccess )
*/
- if (MP_SHOULD_FAIL_SEND(pAdapter) || pAdapter->DriverNoPhyAccess
+ if (MP_SHOULD_FAIL_SEND(etdev) || etdev->DriverNoPhyAccess
|| !netif_carrier_ok(netdev)) {
DBG_VERBOSE(et131x_dbginfo,
"Can't Tx, Link is DOWN; drop the packet\n");
dev_kfree_skb_any(skb);
skb = NULL;
- pAdapter->net_stats.tx_dropped++;
+ etdev->net_stats.tx_dropped++;
} else {
- status = et131x_send_packet(skb, pAdapter);
+ status = et131x_send_packet(skb, etdev);
if (status == -ENOMEM) {
dev_kfree_skb_any(skb);
skb = NULL;
- pAdapter->net_stats.tx_dropped++;
+ etdev->net_stats.tx_dropped++;
}
}
}
/**
* et131x_send_packet - Do the work to send a packet
* @skb: the packet(s) to send
- * @pAdapter: a pointer to the device's private adapter structure
+ * @etdev: a pointer to the device's private adapter structure
*
* Return 0 in almost all cases; non-zero value in extreme hard failure only.
*
* Assumption: Send spinlock has been acquired
*/
static int et131x_send_packet(struct sk_buff *skb,
- struct et131x_adapter *pAdapter)
+ struct et131x_adapter *etdev)
{
int status = 0;
PMP_TCB pMpTcb = NULL;
}
/* Get a TCB for this packet */
- spin_lock_irqsave(&pAdapter->TCBReadyQLock, lockflags);
+ spin_lock_irqsave(&etdev->TCBReadyQLock, lockflags);
- pMpTcb = pAdapter->TxRing.TCBReadyQueueHead;
+ pMpTcb = etdev->TxRing.TCBReadyQueueHead;
if (pMpTcb == NULL) {
- spin_unlock_irqrestore(&pAdapter->TCBReadyQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBReadyQLock, lockflags);
DBG_WARNING(et131x_dbginfo, "Can't obtain a TCB\n");
DBG_TX_LEAVE(et131x_dbginfo);
return -ENOMEM;
}
- pAdapter->TxRing.TCBReadyQueueHead = pMpTcb->Next;
+ etdev->TxRing.TCBReadyQueueHead = pMpTcb->Next;
- if (pAdapter->TxRing.TCBReadyQueueHead == NULL)
- pAdapter->TxRing.TCBReadyQueueTail = NULL;
+ if (etdev->TxRing.TCBReadyQueueHead == NULL)
+ etdev->TxRing.TCBReadyQueueTail = NULL;
- spin_unlock_irqrestore(&pAdapter->TCBReadyQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBReadyQLock, lockflags);
pMpTcb->PacketLength = skb->len;
pMpTcb->Packet = skb;
/* Call the NIC specific send handler. */
if (status == 0)
- status = nic_send_packet(pAdapter, pMpTcb);
+ status = nic_send_packet(etdev, pMpTcb);
if (status != 0) {
- spin_lock_irqsave(&pAdapter->TCBReadyQLock, lockflags);
+ spin_lock_irqsave(&etdev->TCBReadyQLock, lockflags);
- if (pAdapter->TxRing.TCBReadyQueueTail) {
- pAdapter->TxRing.TCBReadyQueueTail->Next = pMpTcb;
+ if (etdev->TxRing.TCBReadyQueueTail) {
+ etdev->TxRing.TCBReadyQueueTail->Next = pMpTcb;
} else {
/* Apparently ready Q is empty. */
- pAdapter->TxRing.TCBReadyQueueHead = pMpTcb;
+ etdev->TxRing.TCBReadyQueueHead = pMpTcb;
}
- pAdapter->TxRing.TCBReadyQueueTail = pMpTcb;
+ etdev->TxRing.TCBReadyQueueTail = pMpTcb;
- spin_unlock_irqrestore(&pAdapter->TCBReadyQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBReadyQLock, lockflags);
DBG_TX_LEAVE(et131x_dbginfo);
return status;
}
- DBG_ASSERT(pAdapter->TxRing.nBusySend <= NUM_TCB);
+ DBG_ASSERT(etdev->TxRing.nBusySend <= NUM_TCB);
DBG_TX_LEAVE(et131x_dbginfo);
return 0;
/**
* nic_send_packet - NIC specific send handler for version B silicon.
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
* @pMpTcb: pointer to MP_TCB
*
* Returns 0 or errno.
*/
-static int nic_send_packet(struct et131x_adapter *pAdapter, PMP_TCB pMpTcb)
+static int nic_send_packet(struct et131x_adapter *etdev, PMP_TCB pMpTcb)
{
uint32_t loopIndex;
TX_DESC_ENTRY_t CurDesc[24];
"filling desc entry %d, "
"TCB: 0x%p\n",
(pPacket->len - pPacket->data_len),
- pAdapter->TxRing.txDmaReadyToSend.bits.
+ etdev->TxRing.txDmaReadyToSend.bits.
val, pMpTcb);
CurDesc[FragmentNumber].DataBufferPtrHigh = 0;
* subsystem)
*/
CurDesc[FragmentNumber++].DataBufferPtrLow =
- pci_map_single(pAdapter->pdev,
+ pci_map_single(etdev->pdev,
pPacket->data,
pPacket->len -
pPacket->data_len,
"filling desc entry %d, "
"TCB: 0x%p\n",
(pPacket->len - pPacket->data_len),
- pAdapter->TxRing.txDmaReadyToSend.bits.
+ etdev->TxRing.txDmaReadyToSend.bits.
val, pMpTcb);
CurDesc[FragmentNumber].DataBufferPtrHigh = 0;
* subsystem)
*/
CurDesc[FragmentNumber++].DataBufferPtrLow =
- pci_map_single(pAdapter->pdev,
+ pci_map_single(etdev->pdev,
pPacket->data,
((pPacket->len -
pPacket->data_len) / 2),
* subsystem)
*/
CurDesc[FragmentNumber++].DataBufferPtrLow =
- pci_map_single(pAdapter->pdev,
+ pci_map_single(etdev->pdev,
pPacket->data +
((pPacket->len -
pPacket->data_len) / 2),
"filling desc entry %d\n"
"TCB: 0x%p\n",
pFragList[loopIndex].size,
- pAdapter->TxRing.txDmaReadyToSend.bits.val,
+ etdev->TxRing.txDmaReadyToSend.bits.val,
pMpTcb);
CurDesc[FragmentNumber].DataBufferPtrHigh = 0;
* addressable (as defined by the pci/dma subsystem)
*/
CurDesc[FragmentNumber++].DataBufferPtrLow =
- pci_map_page(pAdapter->pdev,
+ pci_map_page(etdev->pdev,
pFragList[loopIndex - 1].page,
pFragList[loopIndex - 1].page_offset,
pFragList[loopIndex - 1].size,
return -EIO;
}
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
- if (++pAdapter->TxRing.TxPacketsSinceLastinterrupt ==
- pAdapter->RegistryTxNumBuffers) {
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
+ if (++etdev->TxRing.TxPacketsSinceLastinterrupt ==
+ etdev->RegistryTxNumBuffers) {
CurDesc[FragmentNumber - 1].word3.value = 0x5;
- pAdapter->TxRing.TxPacketsSinceLastinterrupt = 0;
+ etdev->TxRing.TxPacketsSinceLastinterrupt = 0;
} else {
CurDesc[FragmentNumber - 1].word3.value = 0x1;
}
CurDesc[0].word3.bits.f = 1;
- pMpTcb->WrIndexStart = pAdapter->TxRing.txDmaReadyToSend;
+ pMpTcb->WrIndexStart = etdev->TxRing.txDmaReadyToSend;
pMpTcb->PacketStaleCount = 0;
- spin_lock_irqsave(&pAdapter->SendHWLock, lockflags1);
+ spin_lock_irqsave(&etdev->SendHWLock, lockflags1);
iThisCopy =
- NUM_DESC_PER_RING_TX - pAdapter->TxRing.txDmaReadyToSend.bits.val;
+ NUM_DESC_PER_RING_TX - etdev->TxRing.txDmaReadyToSend.bits.val;
if (iThisCopy >= FragmentNumber) {
iRemainder = 0;
iRemainder = FragmentNumber - iThisCopy;
}
- memcpy(pAdapter->TxRing.pTxDescRingVa +
- pAdapter->TxRing.txDmaReadyToSend.bits.val, CurDesc,
+ memcpy(etdev->TxRing.pTxDescRingVa +
+ etdev->TxRing.txDmaReadyToSend.bits.val, CurDesc,
sizeof(TX_DESC_ENTRY_t) * iThisCopy);
- pAdapter->TxRing.txDmaReadyToSend.bits.val += iThisCopy;
+ etdev->TxRing.txDmaReadyToSend.bits.val += iThisCopy;
- if ((pAdapter->TxRing.txDmaReadyToSend.bits.val == 0) ||
- (pAdapter->TxRing.txDmaReadyToSend.bits.val ==
+ if ((etdev->TxRing.txDmaReadyToSend.bits.val == 0) ||
+ (etdev->TxRing.txDmaReadyToSend.bits.val ==
NUM_DESC_PER_RING_TX)) {
- if (pAdapter->TxRing.txDmaReadyToSend.bits.wrap)
- pAdapter->TxRing.txDmaReadyToSend.value = 0;
+ if (etdev->TxRing.txDmaReadyToSend.bits.wrap)
+ etdev->TxRing.txDmaReadyToSend.value = 0;
else
- pAdapter->TxRing.txDmaReadyToSend.value = 0x400;
+ etdev->TxRing.txDmaReadyToSend.value = 0x400;
}
if (iRemainder) {
- memcpy(pAdapter->TxRing.pTxDescRingVa,
+ memcpy(etdev->TxRing.pTxDescRingVa,
CurDesc + iThisCopy,
sizeof(TX_DESC_ENTRY_t) * iRemainder);
- pAdapter->TxRing.txDmaReadyToSend.bits.val += iRemainder;
+ etdev->TxRing.txDmaReadyToSend.bits.val += iRemainder;
}
- if (pAdapter->TxRing.txDmaReadyToSend.bits.val == 0) {
- if (pAdapter->TxRing.txDmaReadyToSend.value)
+ if (etdev->TxRing.txDmaReadyToSend.bits.val == 0) {
+ if (etdev->TxRing.txDmaReadyToSend.value)
pMpTcb->WrIndex.value = NUM_DESC_PER_RING_TX - 1;
else
pMpTcb->WrIndex.value =
0x400 | (NUM_DESC_PER_RING_TX - 1);
} else
pMpTcb->WrIndex.value =
- pAdapter->TxRing.txDmaReadyToSend.value - 1;
+ etdev->TxRing.txDmaReadyToSend.value - 1;
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags2);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags2);
- if (pAdapter->TxRing.CurrSendTail)
- pAdapter->TxRing.CurrSendTail->Next = pMpTcb;
+ if (etdev->TxRing.CurrSendTail)
+ etdev->TxRing.CurrSendTail->Next = pMpTcb;
else
- pAdapter->TxRing.CurrSendHead = pMpTcb;
+ etdev->TxRing.CurrSendHead = pMpTcb;
- pAdapter->TxRing.CurrSendTail = pMpTcb;
+ etdev->TxRing.CurrSendTail = pMpTcb;
DBG_ASSERT(pMpTcb->Next == NULL);
- pAdapter->TxRing.nBusySend++;
+ etdev->TxRing.nBusySend++;
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags2);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags2);
/* Write the new write pointer back to the device. */
- writel(pAdapter->TxRing.txDmaReadyToSend.value,
- &pAdapter->CSRAddress->txdma.service_request.value);
+ writel(etdev->TxRing.txDmaReadyToSend.value,
+ &etdev->CSRAddress->txdma.service_request.value);
/* For Gig only, we use Tx Interrupt coalescing. Enable the software
* timer to wake us up if this packet isn't followed by N more.
*/
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
- writel(pAdapter->RegistryTxTimeInterval * NANO_IN_A_MICRO,
- &pAdapter->CSRAddress->global.watchdog_timer);
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
+ writel(etdev->RegistryTxTimeInterval * NANO_IN_A_MICRO,
+ &etdev->CSRAddress->global.watchdog_timer);
}
- spin_unlock_irqrestore(&pAdapter->SendHWLock, lockflags1);
+ spin_unlock_irqrestore(&etdev->SendHWLock, lockflags1);
DBG_TX_LEAVE(et131x_dbginfo);
return 0;
/**
* NICSendPacket - NIC specific send handler.
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
* @pMpTcb: pointer to MP_TCB
*
* Returns 0 on succes, errno on failure.
* This version of the send routine is designed for version A silicon.
* Assumption - Send spinlock has been acquired.
*/
-static int nic_send_packet(struct et131x_adapter *pAdapter, PMP_TCB pMpTcb)
+static int nic_send_packet(struct et131x_adapter *etdev, PMP_TCB pMpTcb)
{
uint32_t loopIndex, fragIndex, loopEnd;
uint32_t iSplitFirstElement = 0;
DBG_TX_ENTER(et131x_dbginfo);
ServiceComplete.value =
- readl(&pAdapter->CSRAddress->txdma.NewServiceComplete.value);
+ readl(&etdev->CSRAddress->txdma.NewServiceComplete.value);
/*
* Attempt to fix TWO hardware bugs:
DBG_TX(et131x_dbginfo,
"pMpTcb->PacketLength: %d\n", pMpTcb->PacketLength);
- if ((pAdapter->uiDuplexMode == 0)
+ if ((etdev->uiDuplexMode == 0)
&& (pMpTcb->PacketLength < NIC_MIN_PACKET_SIZE)) {
DBG_TX(et131x_dbginfo,
"HALF DUPLEX mode AND len < MIN_PKT_SIZE\n");
SegmentSize = (pPacket->len - pPacket->data_len) / 2;
}
- spin_lock_irqsave(&pAdapter->SendHWLock, lockflags1);
+ spin_lock_irqsave(&etdev->SendHWLock, lockflags1);
- if (pAdapter->TxRing.txDmaReadyToSend.bits.serv_req_wrap ==
+ if (etdev->TxRing.txDmaReadyToSend.bits.serv_req_wrap ==
ServiceComplete.bits.serv_cpl_wrap) {
/* The ring hasn't wrapped. Slots available should be
* (RING_SIZE) - the difference between the two pointers.
*/
SlotsAvailable = NUM_DESC_PER_RING_TX -
- (pAdapter->TxRing.txDmaReadyToSend.bits.serv_req -
+ (etdev->TxRing.txDmaReadyToSend.bits.serv_req -
ServiceComplete.bits.serv_cpl);
} else {
/* The ring has wrapped. Slots available should be the
* difference between the two pointers.
*/
SlotsAvailable = ServiceComplete.bits.serv_cpl -
- pAdapter->TxRing.txDmaReadyToSend.bits.serv_req;
+ etdev->TxRing.txDmaReadyToSend.bits.serv_req;
}
if ((FragListCount + iSplitFirstElement) > SlotsAvailable) {
DBG_WARNING(et131x_dbginfo,
"Not Enough Space in Tx Desc Ring\n");
- spin_unlock_irqrestore(&pAdapter->SendHWLock, lockflags1);
+ spin_unlock_irqrestore(&etdev->SendHWLock, lockflags1);
return -ENOMEM;
}
"Packet Length %d,"
"filling desc entry %d\n",
pPacket->len,
- pAdapter->TxRing.txDmaReadyToSend.bits.serv_req);
+ etdev->TxRing.txDmaReadyToSend.bits.serv_req);
/*
* NOTE - Should we do a paranoia check here to make sure the fragment
length_in_bytes =
SegmentSize;
CurDesc.DataBufferPtrLow =
- pci_map_single(pAdapter->
+ pci_map_single(etdev->
pdev,
pPacket->
data,
pPacket->data_len) -
SegmentSize);
CurDesc.DataBufferPtrLow =
- pci_map_single(pAdapter->
+ pci_map_single(etdev->
pdev,
(pPacket->
data +
pPacket->len - pPacket->data_len;
CurDesc.DataBufferPtrLow =
- pci_map_single(pAdapter->pdev,
+ pci_map_single(etdev->pdev,
pPacket->data,
(pPacket->len -
pPacket->data_len),
CurDesc.word2.bits.length_in_bytes =
pFragList[fragIndex - 1].size;
CurDesc.DataBufferPtrLow =
- pci_map_page(pAdapter->pdev,
+ pci_map_page(etdev->pdev,
pFragList[fragIndex - 1].page,
pFragList[fragIndex -
1].page_offset,
CurDesc.word3.bits.f = 1;
pMpTcb->WrIndexStart =
- pAdapter->TxRing.txDmaReadyToSend;
+ etdev->TxRing.txDmaReadyToSend;
}
if ((loopIndex == (loopEnd - 1)) &&
- (pAdapter->uiDuplexMode ||
+ (etdev->uiDuplexMode ||
(pMpTcb->PacketLength >= NIC_MIN_PACKET_SIZE))) {
/* This is the Last descriptor of the packet */
DBG_TX(et131x_dbginfo,
"THIS is our LAST descriptor\n");
- if (pAdapter->uiLinkSpeed ==
+ if (etdev->uiLinkSpeed ==
TRUEPHY_SPEED_1000MBPS) {
- if (++pAdapter->TxRing.
+ if (++etdev->TxRing.
TxPacketsSinceLastinterrupt >=
- pAdapter->RegistryTxNumBuffers) {
+ etdev->RegistryTxNumBuffers) {
CurDesc.word3.value = 0x5;
- pAdapter->TxRing.
+ etdev->TxRing.
TxPacketsSinceLastinterrupt
= 0;
} else {
* of packet
*/
pMpTcb->WrIndex =
- pAdapter->TxRing.txDmaReadyToSend;
+ etdev->TxRing.txDmaReadyToSend;
pMpTcb->PacketStaleCount = 0;
}
* descriptor ring at the next free entry. Advance
* the "next free entry" variable
*/
- memcpy(pAdapter->TxRing.pTxDescRingVa +
- pAdapter->TxRing.txDmaReadyToSend.bits.serv_req,
+ memcpy(etdev->TxRing.pTxDescRingVa +
+ etdev->TxRing.txDmaReadyToSend.bits.serv_req,
&CurDesc, sizeof(TX_DESC_ENTRY_t));
CurDescPostCopy =
- pAdapter->TxRing.pTxDescRingVa +
- pAdapter->TxRing.txDmaReadyToSend.bits.serv_req;
+ etdev->TxRing.pTxDescRingVa +
+ etdev->TxRing.txDmaReadyToSend.bits.serv_req;
DBG_TX(et131x_dbginfo,
"CURRENT DESCRIPTOR\n"
CurDescPostCopy->word2.value,
CurDescPostCopy->word3.value);
- if (++pAdapter->TxRing.txDmaReadyToSend.bits.serv_req >=
+ if (++etdev->TxRing.txDmaReadyToSend.bits.serv_req >=
NUM_DESC_PER_RING_TX) {
- if (pAdapter->TxRing.txDmaReadyToSend.bits.
+ if (etdev->TxRing.txDmaReadyToSend.bits.
serv_req_wrap) {
- pAdapter->TxRing.txDmaReadyToSend.
+ etdev->TxRing.txDmaReadyToSend.
value = 0;
} else {
- pAdapter->TxRing.txDmaReadyToSend.
+ etdev->TxRing.txDmaReadyToSend.
value = 0x400;
}
}
}
}
- if (pAdapter->uiDuplexMode == 0 &&
+ if (etdev->uiDuplexMode == 0 &&
pMpTcb->PacketLength < NIC_MIN_PACKET_SIZE) {
/* NOTE - Same 32/64-bit issue as above... */
CurDesc.DataBufferPtrHigh = 0x0;
- CurDesc.DataBufferPtrLow = pAdapter->TxRing.pTxDummyBlkPa;
+ CurDesc.DataBufferPtrLow = etdev->TxRing.pTxDummyBlkPa;
CurDesc.word2.value = 0;
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
- if (++pAdapter->TxRing.TxPacketsSinceLastinterrupt >=
- pAdapter->RegistryTxNumBuffers) {
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
+ if (++etdev->TxRing.TxPacketsSinceLastinterrupt >=
+ etdev->RegistryTxNumBuffers) {
CurDesc.word3.value = 0x5;
- pAdapter->TxRing.TxPacketsSinceLastinterrupt =
+ etdev->TxRing.TxPacketsSinceLastinterrupt =
0;
} else {
CurDesc.word3.value = 0x1;
CurDesc.word2.bits.length_in_bytes =
NIC_MIN_PACKET_SIZE - pMpTcb->PacketLength;
- pMpTcb->WrIndex = pAdapter->TxRing.txDmaReadyToSend;
+ pMpTcb->WrIndex = etdev->TxRing.txDmaReadyToSend;
- memcpy(pAdapter->TxRing.pTxDescRingVa +
- pAdapter->TxRing.txDmaReadyToSend.bits.serv_req,
+ memcpy(etdev->TxRing.pTxDescRingVa +
+ etdev->TxRing.txDmaReadyToSend.bits.serv_req,
&CurDesc, sizeof(TX_DESC_ENTRY_t));
CurDescPostCopy =
- pAdapter->TxRing.pTxDescRingVa +
- pAdapter->TxRing.txDmaReadyToSend.bits.serv_req;
+ etdev->TxRing.pTxDescRingVa +
+ etdev->TxRing.txDmaReadyToSend.bits.serv_req;
DBG_TX(et131x_dbginfo,
"CURRENT DESCRIPTOR\n"
CurDescPostCopy->word2.value,
CurDescPostCopy->word3.value);
- if (++pAdapter->TxRing.txDmaReadyToSend.bits.serv_req >=
+ if (++etdev->TxRing.txDmaReadyToSend.bits.serv_req >=
NUM_DESC_PER_RING_TX) {
- if (pAdapter->TxRing.txDmaReadyToSend.bits.
+ if (etdev->TxRing.txDmaReadyToSend.bits.
serv_req_wrap) {
- pAdapter->TxRing.txDmaReadyToSend.value = 0;
+ etdev->TxRing.txDmaReadyToSend.value = 0;
} else {
- pAdapter->TxRing.txDmaReadyToSend.value = 0x400;
+ etdev->TxRing.txDmaReadyToSend.value = 0x400;
}
}
DBG_TX(et131x_dbginfo, "Padding descriptor %d by %d bytes\n",
- /* pAdapter->TxRing.txDmaReadyToSend.value, */
- pAdapter->TxRing.txDmaReadyToSend.bits.serv_req,
+ /* etdev->TxRing.txDmaReadyToSend.value, */
+ etdev->TxRing.txDmaReadyToSend.bits.serv_req,
NIC_MIN_PACKET_SIZE - pMpTcb->PacketLength);
}
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags2);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags2);
- if (pAdapter->TxRing.CurrSendTail)
- pAdapter->TxRing.CurrSendTail->Next = pMpTcb;
+ if (etdev->TxRing.CurrSendTail)
+ etdev->TxRing.CurrSendTail->Next = pMpTcb;
else
- pAdapter->TxRing.CurrSendHead = pMpTcb;
+ etdev->TxRing.CurrSendHead = pMpTcb;
- pAdapter->TxRing.CurrSendTail = pMpTcb;
+ etdev->TxRing.CurrSendTail = pMpTcb;
DBG_ASSERT(pMpTcb->Next == NULL);
- pAdapter->TxRing.nBusySend++;
+ etdev->TxRing.nBusySend++;
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags2);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags2);
/* Write the new write pointer back to the device. */
- writel(pAdapter->TxRing.txDmaReadyToSend.value,
- &pAdapter->CSRAddress->txdma.service_request.value);
+ writel(etdev->TxRing.txDmaReadyToSend.value,
+ &etdev->CSRAddress->txdma.service_request.value);
#ifdef CONFIG_ET131X_DEBUG
- DumpDeviceBlock(DBG_TX_ON, pAdapter, 1);
+ DumpDeviceBlock(DBG_TX_ON, etdev, 1);
#endif
/* For Gig only, we use Tx Interrupt coalescing. Enable the software
* timer to wake us up if this packet isn't followed by N more.
*/
- if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
- writel(pAdapter->RegistryTxTimeInterval * NANO_IN_A_MICRO,
- &pAdapter->CSRAddress->global.watchdog_timer);
+ if (etdev->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
+ writel(etdev->RegistryTxTimeInterval * NANO_IN_A_MICRO,
+ &etdev->CSRAddress->global.watchdog_timer);
}
- spin_unlock_irqrestore(&pAdapter->SendHWLock, lockflags1);
+ spin_unlock_irqrestore(&etdev->SendHWLock, lockflags1);
DBG_TX_LEAVE(et131x_dbginfo);
return 0;
/**
* et131x_free_send_packet - Recycle a MP_TCB, complete the packet if necessary
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
* @pMpTcb: pointer to MP_TCB
*
* Assumption - Send spinlock has been acquired
*/
-inline void et131x_free_send_packet(struct et131x_adapter *pAdapter,
+inline void et131x_free_send_packet(struct et131x_adapter *etdev,
PMP_TCB pMpTcb)
{
unsigned long lockflags;
TX_DESC_ENTRY_t *desc = NULL;
- struct net_device_stats *stats = &pAdapter->net_stats;
+ struct net_device_stats *stats = &etdev->net_stats;
if (MP_TEST_FLAG(pMpTcb, fMP_DEST_BROAD))
- atomic_inc(&pAdapter->Stats.brdcstxmt);
+ atomic_inc(&etdev->Stats.brdcstxmt);
else if (MP_TEST_FLAG(pMpTcb, fMP_DEST_MULTI))
- atomic_inc(&pAdapter->Stats.multixmt);
+ atomic_inc(&etdev->Stats.multixmt);
else
- atomic_inc(&pAdapter->Stats.unixmt);
+ atomic_inc(&etdev->Stats.unixmt);
if (pMpTcb->Packet) {
stats->tx_bytes += pMpTcb->Packet->len;
do {
desc =
- (TX_DESC_ENTRY_t *) (pAdapter->TxRing.
+ (TX_DESC_ENTRY_t *) (etdev->TxRing.
pTxDescRingVa +
pMpTcb->WrIndexStart.bits.val);
desc->word2.value,
desc->word3.value);
- pci_unmap_single(pAdapter->pdev,
+ pci_unmap_single(etdev->pdev,
desc->DataBufferPtrLow,
desc->word2.value, PCI_DMA_TODEVICE);
else
pMpTcb->WrIndexStart.value = 0x400;
}
- } while (desc != (pAdapter->TxRing.pTxDescRingVa +
+ } while (desc != (etdev->TxRing.pTxDescRingVa +
pMpTcb->WrIndex.bits.val));
DBG_TX(et131x_dbginfo,
memset(pMpTcb, 0, sizeof(MP_TCB));
/* Add the TCB to the Ready Q */
- spin_lock_irqsave(&pAdapter->TCBReadyQLock, lockflags);
+ spin_lock_irqsave(&etdev->TCBReadyQLock, lockflags);
- pAdapter->Stats.opackets++;
+ etdev->Stats.opackets++;
- if (pAdapter->TxRing.TCBReadyQueueTail) {
- pAdapter->TxRing.TCBReadyQueueTail->Next = pMpTcb;
+ if (etdev->TxRing.TCBReadyQueueTail) {
+ etdev->TxRing.TCBReadyQueueTail->Next = pMpTcb;
} else {
/* Apparently ready Q is empty. */
- pAdapter->TxRing.TCBReadyQueueHead = pMpTcb;
+ etdev->TxRing.TCBReadyQueueHead = pMpTcb;
}
- pAdapter->TxRing.TCBReadyQueueTail = pMpTcb;
+ etdev->TxRing.TCBReadyQueueTail = pMpTcb;
- spin_unlock_irqrestore(&pAdapter->TCBReadyQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBReadyQLock, lockflags);
- DBG_ASSERT(pAdapter->TxRing.nBusySend >= 0);
+ DBG_ASSERT(etdev->TxRing.nBusySend >= 0);
}
/**
* et131x_free_busy_send_packets - Free and complete the stopped active sends
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Assumption - Send spinlock has been acquired
*/
-void et131x_free_busy_send_packets(struct et131x_adapter *pAdapter)
+void et131x_free_busy_send_packets(struct et131x_adapter *etdev)
{
PMP_TCB pMpTcb;
struct list_head *pEntry;
DBG_ENTER(et131x_dbginfo);
- while (!list_empty(&pAdapter->TxRing.SendWaitQueue)) {
- spin_lock_irqsave(&pAdapter->SendWaitLock, lockflags);
+ while (!list_empty(&etdev->TxRing.SendWaitQueue)) {
+ spin_lock_irqsave(&etdev->SendWaitLock, lockflags);
- pAdapter->TxRing.nWaitSend--;
- spin_unlock_irqrestore(&pAdapter->SendWaitLock, lockflags);
+ etdev->TxRing.nWaitSend--;
+ spin_unlock_irqrestore(&etdev->SendWaitLock, lockflags);
- pEntry = pAdapter->TxRing.SendWaitQueue.next;
+ pEntry = etdev->TxRing.SendWaitQueue.next;
}
- pAdapter->TxRing.nWaitSend = 0;
+ etdev->TxRing.nWaitSend = 0;
/* Any packets being sent? Check the first TCB on the send list */
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags);
- pMpTcb = pAdapter->TxRing.CurrSendHead;
+ pMpTcb = etdev->TxRing.CurrSendHead;
while ((pMpTcb != NULL) && (FreeCounter < NUM_TCB)) {
PMP_TCB pNext = pMpTcb->Next;
- pAdapter->TxRing.CurrSendHead = pNext;
+ etdev->TxRing.CurrSendHead = pNext;
if (pNext == NULL)
- pAdapter->TxRing.CurrSendTail = NULL;
+ etdev->TxRing.CurrSendTail = NULL;
- pAdapter->TxRing.nBusySend--;
+ etdev->TxRing.nBusySend--;
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags);
DBG_VERBOSE(et131x_dbginfo, "pMpTcb = 0x%p\n", pMpTcb);
FreeCounter++;
- MP_FREE_SEND_PACKET_FUN(pAdapter, pMpTcb);
+ MP_FREE_SEND_PACKET_FUN(etdev, pMpTcb);
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags);
- pMpTcb = pAdapter->TxRing.CurrSendHead;
+ pMpTcb = etdev->TxRing.CurrSendHead;
}
if (FreeCounter == NUM_TCB) {
BUG();
}
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags);
- pAdapter->TxRing.nBusySend = 0;
+ etdev->TxRing.nBusySend = 0;
DBG_LEAVE(et131x_dbginfo);
}
/**
* et131x_handle_send_interrupt - Interrupt handler for sending processing
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Re-claim the send resources, complete sends and get more to send from
* the send wait queue.
*
* Assumption - Send spinlock has been acquired
*/
-void et131x_handle_send_interrupt(struct et131x_adapter *pAdapter)
+void et131x_handle_send_interrupt(struct et131x_adapter *etdev)
{
DBG_TX_ENTER(et131x_dbginfo);
/* Mark as completed any packets which have been sent by the device. */
- et131x_update_tcb_list(pAdapter);
+ et131x_update_tcb_list(etdev);
/* If we queued any transmits because we didn't have any TCBs earlier,
* dequeue and send those packets now, as long as we have free TCBs.
*/
- et131x_check_send_wait_list(pAdapter);
+ et131x_check_send_wait_list(etdev);
DBG_TX_LEAVE(et131x_dbginfo);
}
/**
* et131x_update_tcb_list - Helper routine for Send Interrupt handler
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Re-claims the send resources and completes sends. Can also be called as
* part of the NIC send routine when the "ServiceComplete" indication has
* wrapped.
*/
-static void et131x_update_tcb_list(struct et131x_adapter *pAdapter)
+static void et131x_update_tcb_list(struct et131x_adapter *etdev)
{
unsigned long lockflags;
DMA10W_t ServiceComplete;
PMP_TCB pMpTcb;
ServiceComplete.value =
- readl(&pAdapter->CSRAddress->txdma.NewServiceComplete.value);
+ readl(&etdev->CSRAddress->txdma.NewServiceComplete.value);
/* Has the ring wrapped? Process any descriptors that do not have
* the same "wrap" indicator as the current completion indicator
*/
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags);
- pMpTcb = pAdapter->TxRing.CurrSendHead;
+ pMpTcb = etdev->TxRing.CurrSendHead;
while (pMpTcb &&
ServiceComplete.bits.wrap != pMpTcb->WrIndex.bits.wrap &&
ServiceComplete.bits.val < pMpTcb->WrIndex.bits.val) {
- pAdapter->TxRing.nBusySend--;
- pAdapter->TxRing.CurrSendHead = pMpTcb->Next;
+ etdev->TxRing.nBusySend--;
+ etdev->TxRing.CurrSendHead = pMpTcb->Next;
if (pMpTcb->Next == NULL)
- pAdapter->TxRing.CurrSendTail = NULL;
+ etdev->TxRing.CurrSendTail = NULL;
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags);
- MP_FREE_SEND_PACKET_FUN(pAdapter, pMpTcb);
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags);
+ MP_FREE_SEND_PACKET_FUN(etdev, pMpTcb);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags);
/* Goto the next packet */
- pMpTcb = pAdapter->TxRing.CurrSendHead;
+ pMpTcb = etdev->TxRing.CurrSendHead;
}
while (pMpTcb &&
ServiceComplete.bits.wrap == pMpTcb->WrIndex.bits.wrap &&
ServiceComplete.bits.val > pMpTcb->WrIndex.bits.val) {
- pAdapter->TxRing.nBusySend--;
- pAdapter->TxRing.CurrSendHead = pMpTcb->Next;
+ etdev->TxRing.nBusySend--;
+ etdev->TxRing.CurrSendHead = pMpTcb->Next;
if (pMpTcb->Next == NULL)
- pAdapter->TxRing.CurrSendTail = NULL;
+ etdev->TxRing.CurrSendTail = NULL;
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags);
- MP_FREE_SEND_PACKET_FUN(pAdapter, pMpTcb);
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags);
+ MP_FREE_SEND_PACKET_FUN(etdev, pMpTcb);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags);
/* Goto the next packet */
- pMpTcb = pAdapter->TxRing.CurrSendHead;
+ pMpTcb = etdev->TxRing.CurrSendHead;
}
/* Wake up the queue when we hit a low-water mark */
- if (pAdapter->TxRing.nBusySend <= (NUM_TCB / 3))
- netif_wake_queue(pAdapter->netdev);
+ if (etdev->TxRing.nBusySend <= (NUM_TCB / 3))
+ netif_wake_queue(etdev->netdev);
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags);
}
/**
* et131x_check_send_wait_list - Helper routine for the interrupt handler
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Takes packets from the send wait queue and posts them to the device (if
* room available).
*/
-static void et131x_check_send_wait_list(struct et131x_adapter *pAdapter)
+static void et131x_check_send_wait_list(struct et131x_adapter *etdev)
{
unsigned long lockflags;
- spin_lock_irqsave(&pAdapter->SendWaitLock, lockflags);
+ spin_lock_irqsave(&etdev->SendWaitLock, lockflags);
- while (!list_empty(&pAdapter->TxRing.SendWaitQueue) &&
- MP_TCB_RESOURCES_AVAILABLE(pAdapter)) {
+ while (!list_empty(&etdev->TxRing.SendWaitQueue) &&
+ MP_TCB_RESOURCES_AVAILABLE(etdev)) {
struct list_head *pEntry;
DBG_VERBOSE(et131x_dbginfo, "Tx packets on the wait queue\n");
- pEntry = pAdapter->TxRing.SendWaitQueue.next;
+ pEntry = etdev->TxRing.SendWaitQueue.next;
- pAdapter->TxRing.nWaitSend--;
+ etdev->TxRing.nWaitSend--;
DBG_WARNING(et131x_dbginfo,
"MpHandleSendInterrupt - sent a queued pkt. Waiting %d\n",
- pAdapter->TxRing.nWaitSend);
+ etdev->TxRing.nWaitSend);
}
- spin_unlock_irqrestore(&pAdapter->SendWaitLock, lockflags);
+ spin_unlock_irqrestore(&etdev->SendWaitLock, lockflags);
}
/**
* et131x_config_parse
- * @pAdapter: pointer to the private adapter struct
+ * @etdev: pointer to the private adapter struct
*
* Parses a configuration from some location (module parameters, for example)
* into the private adapter struct
*/
-void et131x_config_parse(struct et131x_adapter *pAdapter)
+void et131x_config_parse(struct et131x_adapter *etdev)
{
uint8_t macAddrDef[] = PARM_MAC_ADDRESS_DEF;
if (et131x_speed_set != PARM_SPEED_DUPLEX_DEF) {
DBG_VERBOSE(et131x_dbginfo, "Speed set manually to : %d \n",
et131x_speed_set);
- pAdapter->SpeedDuplex = et131x_speed_set;
+ etdev->SpeedDuplex = et131x_speed_set;
} else {
- pAdapter->SpeedDuplex = PARM_SPEED_DUPLEX_DEF;
+ etdev->SpeedDuplex = PARM_SPEED_DUPLEX_DEF;
}
- /* pAdapter->SpeedDuplex = PARM_SPEED_DUPLEX_DEF; */
-
- pAdapter->RegistryVlanTag = PARM_VLAN_TAG_DEF;
- pAdapter->RegistryFlowControl = PARM_FLOW_CTL_DEF;
- pAdapter->RegistryWOLLink = PARM_WOL_LINK_DEF;
- pAdapter->RegistryWOLMatch = PARM_WOL_MATCH_DEF;
- pAdapter->RegistryJumboPacket = PARM_JUMBO_PKT_DEF;
- pAdapter->RegistryPhyComa = PARM_PHY_COMA_DEF;
- pAdapter->RegistryRxNumBuffers = PARM_RX_NUM_BUFS_DEF;
- pAdapter->RegistryRxTimeInterval = PARM_RX_TIME_INT_DEF;
- pAdapter->RegistryTxNumBuffers = PARM_TX_NUM_BUFS_DEF;
- pAdapter->RegistryTxTimeInterval = PARM_TX_TIME_INT_DEF;
- pAdapter->RegistryRxMemEnd = PARM_RX_MEM_END_DEF;
- pAdapter->RegistryMACStat = PARM_MAC_STAT_DEF;
- pAdapter->RegistrySCGain = PARM_SC_GAIN_DEF;
- pAdapter->RegistryPMWOL = PARM_PM_WOL_DEF;
+ /* etdev->SpeedDuplex = PARM_SPEED_DUPLEX_DEF; */
+
+ etdev->RegistryVlanTag = PARM_VLAN_TAG_DEF;
+ etdev->RegistryFlowControl = PARM_FLOW_CTL_DEF;
+ etdev->RegistryWOLLink = PARM_WOL_LINK_DEF;
+ etdev->RegistryWOLMatch = PARM_WOL_MATCH_DEF;
+ etdev->RegistryJumboPacket = PARM_JUMBO_PKT_DEF;
+ etdev->RegistryPhyComa = PARM_PHY_COMA_DEF;
+ etdev->RegistryRxNumBuffers = PARM_RX_NUM_BUFS_DEF;
+ etdev->RegistryRxTimeInterval = PARM_RX_TIME_INT_DEF;
+ etdev->RegistryTxNumBuffers = PARM_TX_NUM_BUFS_DEF;
+ etdev->RegistryTxTimeInterval = PARM_TX_TIME_INT_DEF;
+ etdev->RegistryRxMemEnd = PARM_RX_MEM_END_DEF;
+ etdev->RegistryMACStat = PARM_MAC_STAT_DEF;
+ etdev->RegistrySCGain = PARM_SC_GAIN_DEF;
+ etdev->RegistryPMWOL = PARM_PM_WOL_DEF;
if (et131x_nmi_disable != PARM_NMI_DISABLE_DEF)
- pAdapter->RegistryNMIDisable = et131x_nmi_disable;
+ etdev->RegistryNMIDisable = et131x_nmi_disable;
else
- pAdapter->RegistryNMIDisable = PARM_NMI_DISABLE_DEF;
+ etdev->RegistryNMIDisable = PARM_NMI_DISABLE_DEF;
- pAdapter->RegistryDMACache = PARM_DMA_CACHE_DEF;
- pAdapter->RegistryPhyLoopbk = PARM_PHY_LOOPBK_DEF;
+ etdev->RegistryDMACache = PARM_DMA_CACHE_DEF;
+ etdev->RegistryPhyLoopbk = PARM_PHY_LOOPBK_DEF;
/* Set the MAC address to a default */
- memcpy(pAdapter->CurrentAddress, macAddrDef, ETH_ALEN);
- pAdapter->bOverrideAddress = false;
+ memcpy(etdev->CurrentAddress, macAddrDef, ETH_ALEN);
+ etdev->bOverrideAddress = false;
DBG_TRACE(et131x_dbginfo,
"Default MAC Address : %02x:%02x:%02x:%02x:%02x:%02x\n",
- pAdapter->CurrentAddress[0], pAdapter->CurrentAddress[1],
- pAdapter->CurrentAddress[2], pAdapter->CurrentAddress[3],
- pAdapter->CurrentAddress[4], pAdapter->CurrentAddress[5]);
+ etdev->CurrentAddress[0], etdev->CurrentAddress[1],
+ etdev->CurrentAddress[2], etdev->CurrentAddress[3],
+ etdev->CurrentAddress[4], etdev->CurrentAddress[5]);
/* Decode SpeedDuplex
*
* Set up as if we are auto negotiating always and then change if we
* go into force mode
*/
- pAdapter->AiForceSpeed = 0; /* Auto speed */
- pAdapter->AiForceDpx = 0; /* Auto FDX */
+ etdev->AiForceSpeed = 0; /* Auto speed */
+ etdev->AiForceDpx = 0; /* Auto FDX */
/* If we are the 10/100 device, and gigabit is somehow requested then
* knock it down to 100 full.
*/
- if (pAdapter->DeviceID == ET131X_PCI_DEVICE_ID_FAST &&
- pAdapter->SpeedDuplex == 5)
- pAdapter->SpeedDuplex = 4;
+ if (etdev->DeviceID == ET131X_PCI_DEVICE_ID_FAST &&
+ etdev->SpeedDuplex == 5)
+ etdev->SpeedDuplex = 4;
- switch (pAdapter->SpeedDuplex) {
+ switch (etdev->SpeedDuplex) {
case 1: /* 10Mb Half-Duplex */
- pAdapter->AiForceSpeed = 10;
- pAdapter->AiForceDpx = 1;
+ etdev->AiForceSpeed = 10;
+ etdev->AiForceDpx = 1;
break;
case 2: /* 10Mb Full-Duplex */
- pAdapter->AiForceSpeed = 10;
- pAdapter->AiForceDpx = 2;
+ etdev->AiForceSpeed = 10;
+ etdev->AiForceDpx = 2;
break;
case 3: /* 100Mb Half-Duplex */
- pAdapter->AiForceSpeed = 100;
- pAdapter->AiForceDpx = 1;
+ etdev->AiForceSpeed = 100;
+ etdev->AiForceDpx = 1;
break;
case 4: /* 100Mb Full-Duplex */
- pAdapter->AiForceSpeed = 100;
- pAdapter->AiForceDpx = 2;
+ etdev->AiForceSpeed = 100;
+ etdev->AiForceDpx = 2;
break;
case 5: /* 1000Mb Full-Duplex */
- pAdapter->AiForceSpeed = 1000;
- pAdapter->AiForceDpx = 2;
+ etdev->AiForceSpeed = 1000;
+ etdev->AiForceDpx = 2;
break;
}
/**
* DumpTxQueueContents - Dump out the tx queue and the shadow pointers
- * @pAdapter: pointer to our adapter structure
+ * @etdev: pointer to our adapter structure
*/
-void DumpTxQueueContents(int dbgLvl, struct et131x_adapter *pAdapter)
+void DumpTxQueueContents(int dbgLvl, struct et131x_adapter *etdev)
{
- MMC_t __iomem *mmc = &pAdapter->CSRAddress->mmc;
+ MMC_t __iomem *mmc = &etdev->CSRAddress->mmc;
uint32_t TxQueueAddr;
if (DBG_FLAGS(et131x_dbginfo) & dbgLvl) {
}
DBG_PRINT("Shadow Pointers 0x%08x\n",
- readl(&pAdapter->CSRAddress->txmac.shadow_ptr.value));
+ readl(&etdev->CSRAddress->txmac.shadow_ptr.value));
}
}
/**
* DumpDeviceBlock
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Dumps the first 64 regs of each block of the et-1310 (each block is
* mapped to a new page, each page is 4096 bytes).
*/
#define NUM_BLOCKS 8
-void DumpDeviceBlock(int dbgLvl, struct et131x_adapter *pAdapter,
+void DumpDeviceBlock(int dbgLvl, struct et131x_adapter *etdev,
uint32_t Block)
{
uint32_t Address1, Address2;
uint32_t __iomem *BigDevicePointer =
- (uint32_t __iomem *) pAdapter->CSRAddress;
+ (uint32_t __iomem *) etdev->CSRAddress;
const char *BlockNames[NUM_BLOCKS] = {
"Global", "Tx DMA", "Rx DMA", "Tx MAC",
"Rx MAC", "MAC", "MAC Stat", "MMC"
/**
* DumpDeviceReg
- * @pAdapter: pointer to our adapter
+ * @etdev: pointer to our adapter
*
* Dumps the first 64 regs of each block of the et-1310 (each block is
* mapped to a new page, each page is 4096 bytes).
*/
-void DumpDeviceReg(int dbgLvl, struct et131x_adapter *pAdapter)
+void DumpDeviceReg(int dbgLvl, struct et131x_adapter *etdev)
{
uint32_t Address1, Address2;
uint32_t Block;
uint32_t __iomem *BigDevicePointer =
- (uint32_t __iomem *) pAdapter->CSRAddress;
+ (uint32_t __iomem *) etdev->CSRAddress;
uint32_t __iomem *Pointer;
const char *BlockNames[NUM_BLOCKS] = {
"Global", "Tx DMA", "Rx DMA", "Tx MAC",
*/
void et131x_error_timer_handler(unsigned long data)
{
- struct et131x_adapter *pAdapter = (struct et131x_adapter *) data;
+ struct et131x_adapter *etdev = (struct et131x_adapter *) data;
PM_CSR_t pm_csr;
- pm_csr.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
+ pm_csr.value = readl(&etdev->CSRAddress->global.pm_csr.value);
if (pm_csr.bits.pm_phy_sw_coma == 0) {
- if (pAdapter->RegistryMACStat)
- UpdateMacStatHostCounters(pAdapter);
+ if (etdev->RegistryMACStat)
+ UpdateMacStatHostCounters(etdev);
} else
DBG_VERBOSE(et131x_dbginfo,
"No interrupts, in PHY coma, pm_csr = 0x%x\n",
pm_csr.value);
- if (!pAdapter->Bmsr.bits.link_status &&
- pAdapter->RegistryPhyComa &&
- pAdapter->PoMgmt.TransPhyComaModeOnBoot < 11) {
- pAdapter->PoMgmt.TransPhyComaModeOnBoot++;
+ if (!etdev->Bmsr.bits.link_status &&
+ etdev->RegistryPhyComa &&
+ etdev->PoMgmt.TransPhyComaModeOnBoot < 11) {
+ etdev->PoMgmt.TransPhyComaModeOnBoot++;
}
- if (pAdapter->PoMgmt.TransPhyComaModeOnBoot == 10) {
- if (!pAdapter->Bmsr.bits.link_status
- && pAdapter->RegistryPhyComa) {
+ if (etdev->PoMgmt.TransPhyComaModeOnBoot == 10) {
+ if (!etdev->Bmsr.bits.link_status
+ && etdev->RegistryPhyComa) {
if (pm_csr.bits.pm_phy_sw_coma == 0) {
/* NOTE - This was originally a 'sync with
* interrupt'. How to do that under Linux?
*/
- et131x_enable_interrupts(pAdapter);
- EnablePhyComa(pAdapter);
+ et131x_enable_interrupts(etdev);
+ EnablePhyComa(etdev);
}
}
}
/* This is a periodic timer, so reschedule */
- mod_timer(&pAdapter->ErrorTimer, jiffies +
+ mod_timer(&etdev->ErrorTimer, jiffies +
TX_ERROR_PERIOD * HZ / 1000);
}
*/
void et131x_link_detection_handler(unsigned long data)
{
- struct et131x_adapter *pAdapter = (struct et131x_adapter *) data;
+ struct et131x_adapter *etdev = (struct et131x_adapter *) data;
unsigned long lockflags;
/* Let everyone know that we have run */
- pAdapter->bLinkTimerActive = false;
+ etdev->bLinkTimerActive = false;
- if (pAdapter->MediaState == 0) {
- spin_lock_irqsave(&pAdapter->Lock, lockflags);
+ if (etdev->MediaState == 0) {
+ spin_lock_irqsave(&etdev->Lock, lockflags);
- pAdapter->MediaState = NETIF_STATUS_MEDIA_DISCONNECT;
- MP_CLEAR_FLAG(pAdapter, fMP_ADAPTER_LINK_DETECTION);
+ etdev->MediaState = NETIF_STATUS_MEDIA_DISCONNECT;
+ MP_CLEAR_FLAG(etdev, fMP_ADAPTER_LINK_DETECTION);
- spin_unlock_irqrestore(&pAdapter->Lock, lockflags);
+ spin_unlock_irqrestore(&etdev->Lock, lockflags);
- netif_carrier_off(pAdapter->netdev);
+ netif_carrier_off(etdev->netdev);
- pAdapter->bSetPending = false;
+ etdev->bSetPending = false;
}
}
*
* Returns 0 on success, errno on failure (as defined in errno.h)
*/
-int et131x_adapter_setup(struct et131x_adapter *pAdapter)
+int et131x_adapter_setup(struct et131x_adapter *etdev)
{
int status = 0;
DBG_ENTER(et131x_dbginfo);
/* Configure the JAGCore */
- ConfigGlobalRegs(pAdapter);
+ ConfigGlobalRegs(etdev);
- ConfigMACRegs1(pAdapter);
- ConfigMMCRegs(pAdapter);
+ ConfigMACRegs1(etdev);
+ ConfigMMCRegs(etdev);
- ConfigRxMacRegs(pAdapter);
- ConfigTxMacRegs(pAdapter);
+ ConfigRxMacRegs(etdev);
+ ConfigTxMacRegs(etdev);
- ConfigRxDmaRegs(pAdapter);
- ConfigTxDmaRegs(pAdapter);
+ ConfigRxDmaRegs(etdev);
+ ConfigTxDmaRegs(etdev);
- ConfigMacStatRegs(pAdapter);
+ ConfigMacStatRegs(etdev);
/* Move the following code to Timer function?? */
- status = et131x_xcvr_find(pAdapter);
+ status = et131x_xcvr_find(etdev);
if (status != 0)
DBG_WARNING(et131x_dbginfo, "Could not find the xcvr\n");
/* Prepare the TRUEPHY library. */
- ET1310_PhyInit(pAdapter);
+ ET1310_PhyInit(etdev);
/* Reset the phy now so changes take place */
- ET1310_PhyReset(pAdapter);
+ ET1310_PhyReset(etdev);
/* Power down PHY */
- ET1310_PhyPowerDown(pAdapter, 1);
+ ET1310_PhyPowerDown(etdev, 1);
/*
* We need to turn off 1000 base half dulplex, the mac does not
* support it. For the 10/100 part, turn off all gig advertisement
*/
- if (pAdapter->DeviceID != ET131X_PCI_DEVICE_ID_FAST)
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_FULL);
+ if (etdev->DeviceID != ET131X_PCI_DEVICE_ID_FAST)
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_FULL);
else
- ET1310_PhyAdvertise1000BaseT(pAdapter, TRUEPHY_ADV_DUPLEX_NONE);
+ ET1310_PhyAdvertise1000BaseT(etdev, TRUEPHY_ADV_DUPLEX_NONE);
/* Power up PHY */
- ET1310_PhyPowerDown(pAdapter, 0);
+ ET1310_PhyPowerDown(etdev, 0);
- et131x_setphy_normal(pAdapter);
+ et131x_setphy_normal(etdev);
DBG_LEAVE(et131x_dbginfo);
return status;
*/
void et131x_isr_handler(struct work_struct *work)
{
- struct et131x_adapter *pAdapter =
+ struct et131x_adapter *etdev =
container_of(work, struct et131x_adapter, task);
- INTERRUPT_t GlobStatus = pAdapter->Stats.InterruptStatus;
- ADDRESS_MAP_t __iomem *iomem = pAdapter->CSRAddress;
+ INTERRUPT_t GlobStatus = etdev->Stats.InterruptStatus;
+ ADDRESS_MAP_t __iomem *iomem = etdev->CSRAddress;
/*
* These first two are by far the most common. Once handled, we clear
/* Handle all the completed Transmit interrupts */
if (GlobStatus.bits.txdma_isr) {
DBG_TX(et131x_dbginfo, "TXDMA_ISR interrupt\n");
- et131x_handle_send_interrupt(pAdapter);
+ et131x_handle_send_interrupt(etdev);
}
/* Handle all the completed Receives interrupts */
if (GlobStatus.bits.rxdma_xfr_done) {
DBG_RX(et131x_dbginfo, "RXDMA_XFR_DONE interrupt\n");
- et131x_handle_recv_interrupt(pAdapter);
+ et131x_handle_recv_interrupt(etdev);
}
GlobStatus.value &= 0xffffffd7;
/* If the user has flow control on, then we will
* send a pause packet, otherwise just exit
*/
- if (pAdapter->FlowControl == TxOnly ||
- pAdapter->FlowControl == Both) {
+ if (etdev->FlowControl == TxOnly ||
+ etdev->FlowControl == Both) {
PM_CSR_t pm_csr;
/* Tell the device to send a pause packet via
*/
/* TRAP();*/
- pAdapter->TxMacTest.value =
+ etdev->TxMacTest.value =
readl(&iomem->txmac.tx_test.value);
DBG_WARNING(et131x_dbginfo,
"RxDMA_ERR interrupt, error %x\n",
- pAdapter->TxMacTest.value);
+ etdev->TxMacTest.value);
}
/* Handle the Wake on LAN Event */
DBG_VERBOSE(et131x_dbginfo,
"Device is in COMA mode, "
"need to wake up\n");
- DisablePhyComa(pAdapter);
+ DisablePhyComa(etdev);
}
/* Read the PHY ISR to clear the reason for the
* interrupt.
*/
- MiRead(pAdapter, (uint8_t) offsetof(MI_REGS_t, isr),
+ MiRead(etdev, (uint8_t) offsetof(MI_REGS_t, isr),
&myIsr.value);
- if (!pAdapter->ReplicaPhyLoopbk) {
- MiRead(pAdapter,
+ if (!etdev->ReplicaPhyLoopbk) {
+ MiRead(etdev,
(uint8_t) offsetof(MI_REGS_t, bmsr),
&BmsrData.value);
BmsrInts.value =
- pAdapter->Bmsr.value ^ BmsrData.value;
- pAdapter->Bmsr.value = BmsrData.value;
+ etdev->Bmsr.value ^ BmsrData.value;
+ etdev->Bmsr.value = BmsrData.value;
DBG_VERBOSE(et131x_dbginfo,
"Bmsr.value = 0x%04x,"
BmsrData.value, BmsrInts.value);
/* Do all the cable in / cable out stuff */
- et131x_Mii_check(pAdapter, BmsrData, BmsrInts);
+ et131x_Mii_check(etdev, BmsrData, BmsrInts);
}
}
/* Let's move on to the TxMac */
if (GlobStatus.bits.txmac_interrupt) {
- pAdapter->TxRing.TxMacErr.value =
+ etdev->TxRing.TxMacErr.value =
readl(&iomem->txmac.err.value);
/*
*/
DBG_WARNING(et131x_dbginfo,
"TXMAC interrupt, error 0x%08x\n",
- pAdapter->TxRing.TxMacErr.value);
+ etdev->TxRing.TxMacErr.value);
/* If we are debugging, we want to see this error,
* otherwise we just want the device to be reset and
* set the flag to cause us to reset so we can solve
* this issue.
*/
- /* MP_SET_FLAG( pAdapter,
+ /* MP_SET_FLAG( etdev,
fMP_ADAPTER_HARDWARE_ERROR); */
DBG_WARNING(et131x_dbginfo,
* counter(s).
*/
DBG_VERBOSE(et131x_dbginfo, "MAC_STAT interrupt\n");
- HandleMacStatInterrupt(pAdapter);
+ HandleMacStatInterrupt(etdev);
}
/* Handle SLV Timeout Interrupt */
}
}
- if (pAdapter->PoMgmt.PowerState == NdisDeviceStateD0)
- et131x_enable_interrupts(pAdapter);
+ if (etdev->PoMgmt.PowerState == NdisDeviceStateD0)
+ et131x_enable_interrupts(etdev);
}
int et131x_ioctl_mii(struct net_device *netdev, struct ifreq *reqbuf, int cmd)
{
int status = 0;
- struct et131x_adapter *pAdapter = netdev_priv(netdev);
+ struct et131x_adapter *etdev = netdev_priv(netdev);
struct mii_ioctl_data *data = if_mii(reqbuf);
DBG_ENTER(et131x_dbginfo);
switch (cmd) {
case SIOCGMIIPHY:
DBG_VERBOSE(et131x_dbginfo, "SIOCGMIIPHY\n");
- data->phy_id = pAdapter->Stats.xcvr_addr;
+ data->phy_id = etdev->Stats.xcvr_addr;
break;
case SIOCGMIIREG:
if (!capable(CAP_NET_ADMIN)) {
status = -EPERM;
} else {
- status = MiRead(pAdapter,
+ status = MiRead(etdev,
data->reg_num, &data->val_out);
}
break;
if (!capable(CAP_NET_ADMIN)) {
status = -EPERM;
} else {
- status = MiWrite(pAdapter, data->reg_num,
+ status = MiWrite(etdev, data->reg_num,
data->val_in);
}
break;
*/
void et131x_tx_timeout(struct net_device *netdev)
{
- struct et131x_adapter *pAdapter = netdev_priv(netdev);
+ struct et131x_adapter *etdev = netdev_priv(netdev);
PMP_TCB pMpTcb;
unsigned long lockflags;
DBG_WARNING(et131x_dbginfo, "TX TIMEOUT\n");
/* Just skip this part if the adapter is doing link detection */
- if (MP_TEST_FLAG(pAdapter, fMP_ADAPTER_LINK_DETECTION)) {
+ if (MP_TEST_FLAG(etdev, fMP_ADAPTER_LINK_DETECTION)) {
DBG_ERROR(et131x_dbginfo, "Still doing link detection\n");
return;
}
/* Any nonrecoverable hardware error?
* Checks adapter->flags for any failure in phy reading
*/
- if (MP_TEST_FLAG(pAdapter, fMP_ADAPTER_NON_RECOVER_ERROR)) {
+ if (MP_TEST_FLAG(etdev, fMP_ADAPTER_NON_RECOVER_ERROR)) {
DBG_WARNING(et131x_dbginfo, "Non recoverable error - remove\n");
return;
}
/* Hardware failure? */
- if (MP_TEST_FLAG(pAdapter, fMP_ADAPTER_HARDWARE_ERROR)) {
+ if (MP_TEST_FLAG(etdev, fMP_ADAPTER_HARDWARE_ERROR)) {
DBG_WARNING(et131x_dbginfo, "hardware error - reset\n");
return;
}
/* Is send stuck? */
- spin_lock_irqsave(&pAdapter->TCBSendQLock, lockflags);
+ spin_lock_irqsave(&etdev->TCBSendQLock, lockflags);
- pMpTcb = pAdapter->TxRing.CurrSendHead;
+ pMpTcb = etdev->TxRing.CurrSendHead;
if (pMpTcb != NULL) {
pMpTcb->Count++;
if (pMpTcb->Count > NIC_SEND_HANG_THRESHOLD) {
#ifdef CONFIG_ET131X_DEBUG
TX_STATUS_BLOCK_t txDmaComplete =
- *(pAdapter->TxRing.pTxStatusVa);
+ *(etdev->TxRing.pTxStatusVa);
PTX_DESC_ENTRY_t pDesc =
- pAdapter->TxRing.pTxDescRingVa +
+ etdev->TxRing.pTxDescRingVa +
pMpTcb->WrIndex.bits.val;
#endif
TX_DESC_ENTRY_t StuckDescriptors[10];
if (pMpTcb->WrIndex.bits.val > 7) {
memcpy(StuckDescriptors,
- pAdapter->TxRing.pTxDescRingVa +
+ etdev->TxRing.pTxDescRingVa +
pMpTcb->WrIndex.bits.val - 6,
sizeof(TX_DESC_ENTRY_t) * 10);
}
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock,
+ spin_unlock_irqrestore(&etdev->TCBSendQLock,
lockflags);
DBG_WARNING(et131x_dbginfo,
"WbStatus 0x%08x\n", txDmaComplete.value);
#ifdef CONFIG_ET131X_DEBUG
- DumpDeviceBlock(DBG_WARNING_ON, pAdapter, 0);
- DumpDeviceBlock(DBG_WARNING_ON, pAdapter, 1);
- DumpDeviceBlock(DBG_WARNING_ON, pAdapter, 3);
- DumpDeviceBlock(DBG_WARNING_ON, pAdapter, 5);
+ DumpDeviceBlock(DBG_WARNING_ON, etdev, 0);
+ DumpDeviceBlock(DBG_WARNING_ON, etdev, 1);
+ DumpDeviceBlock(DBG_WARNING_ON, etdev, 3);
+ DumpDeviceBlock(DBG_WARNING_ON, etdev, 5);
#endif
et131x_close(netdev);
et131x_open(netdev);
}
}
- spin_unlock_irqrestore(&pAdapter->TCBSendQLock, lockflags);
+ spin_unlock_irqrestore(&etdev->TCBSendQLock, lockflags);
}
/**
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff