sfc: Fix some incorrect or redundant comments
authorBen Hutchings <bhutchings@solarflare.com>
Wed, 3 Feb 2010 09:31:57 +0000 (09:31 +0000)
committerDavid S. Miller <davem@davemloft.net>
Thu, 4 Feb 2010 03:12:47 +0000 (19:12 -0800)
In particular, the comment about EVQ_RPTR_REG is based on inconsistent
preliminary hardware documentation, though the following code was
fixed long before release.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sfc/ethtool.c
drivers/net/sfc/falcon.c
drivers/net/sfc/net_driver.h
drivers/net/sfc/nic.c

index 635c420..d9f9c02 100644 (file)
@@ -196,7 +196,7 @@ int efx_ethtool_get_settings(struct net_device *net_dev,
        efx->phy_op->get_settings(efx, ecmd);
        mutex_unlock(&efx->mac_lock);
 
-       /* Falcon GMAC does not support 1000Mbps HD */
+       /* GMAC does not support 1000Mbps HD */
        ecmd->supported &= ~SUPPORTED_1000baseT_Half;
        /* Both MACs support pause frames (bidirectional and respond-only) */
        ecmd->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
@@ -216,7 +216,7 @@ int efx_ethtool_set_settings(struct net_device *net_dev,
        struct efx_nic *efx = netdev_priv(net_dev);
        int rc;
 
-       /* Falcon GMAC does not support 1000Mbps HD */
+       /* GMAC does not support 1000Mbps HD */
        if (ecmd->speed == SPEED_1000 && ecmd->duplex != DUPLEX_FULL) {
                EFX_LOG(efx, "rejecting unsupported 1000Mbps HD"
                        " setting\n");
index f63a32c..1b8d836 100644 (file)
@@ -1730,7 +1730,7 @@ static int falcon_set_wol(struct efx_nic *efx, u32 type)
 
 /**************************************************************************
  *
- * Revision-dependent attributes used by efx.c
+ * Revision-dependent attributes used by efx.c and nic.c
  *
  **************************************************************************
  */
index 8f951e4..ac77a25 100644 (file)
@@ -101,9 +101,6 @@ do {if (net_ratelimit()) EFX_LOG(efx, fmt, ##args); } while (0)
  * Special buffers are used for the event queues and the TX and RX
  * descriptor queues for each channel.  They are *not* used for the
  * actual transmit and receive buffers.
- *
- * Note that for Falcon, TX and RX descriptor queues live in host memory.
- * Allocation and freeing procedures must take this into account.
  */
 struct efx_special_buffer {
        void *addr;
@@ -300,7 +297,7 @@ struct efx_rx_queue {
  * @dma_addr: DMA base address of the buffer
  * @len: Buffer length, in bytes
  *
- * Falcon uses these buffers for its interrupt status registers and
+ * The NIC uses these buffers for its interrupt status registers and
  * MAC stats dumps.
  */
 struct efx_buffer {
@@ -674,7 +671,7 @@ union efx_multicast_hash {
  * @irq_status: Interrupt status buffer
  * @last_irq_cpu: Last CPU to handle interrupt.
  *     This register is written with the SMP processor ID whenever an
- *     interrupt is handled.  It is used by falcon_test_interrupt()
+ *     interrupt is handled.  It is used by efx_nic_test_interrupt()
  *     to verify that an interrupt has occurred.
  * @spi_flash: SPI flash device
  *     This field will be %NULL if no flash device is present (or for Siena).
@@ -723,8 +720,7 @@ union efx_multicast_hash {
  * @loopback_modes: Supported loopback mode bitmask
  * @loopback_selftest: Offline self-test private state
  *
- * The @priv field of the corresponding &struct net_device points to
- * this.
+ * This is stored in the private area of the &struct net_device.
  */
 struct efx_nic {
        char name[IFNAMSIZ];
@@ -997,7 +993,7 @@ static inline void clear_bit_le(unsigned nr, unsigned char *addr)
  * that the net driver will program into the MAC as the maximum frame
  * length.
  *
- * The 10G MAC used in Falcon requires 8-byte alignment on the frame
+ * The 10G MAC requires 8-byte alignment on the frame
  * length, so we round up to the nearest 8.
  *
  * Re-clocking by the XGXS on RX can reduce an IPG to 32 bits (half an
index 8d9696a..b06f8e3 100644 (file)
@@ -623,10 +623,6 @@ void efx_nic_remove_rx(struct efx_rx_queue *rx_queue)
  *
  * This writes the EVQ_RPTR_REG register for the specified channel's
  * event queue.
- *
- * Note that EVQ_RPTR_REG contains the index of the "last read" event,
- * whereas channel->eventq_read_ptr contains the index of the "next to
- * read" event.
  */
 void efx_nic_eventq_read_ack(struct efx_channel *channel)
 {