static s32 igb_init_hw_82575(struct e1000_hw *);
static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *);
static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *);
+static s32 igb_read_phy_reg_82580(struct e1000_hw *, u32, u16 *);
+static s32 igb_write_phy_reg_82580(struct e1000_hw *, u32, u16);
static s32 igb_reset_hw_82575(struct e1000_hw *);
+static s32 igb_reset_hw_82580(struct e1000_hw *);
static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool);
static s32 igb_setup_copper_link_82575(struct e1000_hw *);
static s32 igb_setup_serdes_link_82575(struct e1000_hw *);
static s32 igb_read_mac_addr_82575(struct e1000_hw *);
static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw);
+static const u16 e1000_82580_rxpbs_table[] =
+ { 36, 72, 144, 1, 2, 4, 8, 16,
+ 35, 70, 140 };
+#define E1000_82580_RXPBS_TABLE_SIZE \
+ (sizeof(e1000_82580_rxpbs_table)/sizeof(u16))
+
static s32 igb_get_invariants_82575(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
case E1000_DEV_ID_82576_SERDES_QUAD:
mac->type = e1000_82576;
break;
+ case E1000_DEV_ID_82580_COPPER:
+ case E1000_DEV_ID_82580_FIBER:
+ case E1000_DEV_ID_82580_SERDES:
+ case E1000_DEV_ID_82580_SGMII:
+ case E1000_DEV_ID_82580_COPPER_DUAL:
+ mac->type = e1000_82580;
+ break;
default:
return -E1000_ERR_MAC_INIT;
break;
dev_spec->sgmii_active = true;
ctrl_ext |= E1000_CTRL_I2C_ENA;
break;
+ case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
hw->phy.media_type = e1000_media_type_internal_serdes;
ctrl_ext |= E1000_CTRL_I2C_ENA;
wr32(E1000_CTRL_EXT, ctrl_ext);
+ /*
+ * if using i2c make certain the MDICNFG register is cleared to prevent
+ * communications from being misrouted to the mdic registers
+ */
+ if ((ctrl_ext & E1000_CTRL_I2C_ENA) && (hw->mac.type == e1000_82580))
+ wr32(E1000_MDICNFG, 0);
+
/* Set mta register count */
mac->mta_reg_count = 128;
/* Set rar entry count */
mac->rar_entry_count = E1000_RAR_ENTRIES_82575;
if (mac->type == e1000_82576)
mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
+ if (mac->type == e1000_82580)
+ mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
+ /* reset */
+ if (mac->type == e1000_82580)
+ mac->ops.reset_hw = igb_reset_hw_82580;
+ else
+ mac->ops.reset_hw = igb_reset_hw_82575;
/* Set if part includes ASF firmware */
mac->asf_firmware_present = true;
/* Set if manageability features are enabled. */
phy->ops.reset = igb_phy_hw_reset_sgmii_82575;
phy->ops.read_reg = igb_read_phy_reg_sgmii_82575;
phy->ops.write_reg = igb_write_phy_reg_sgmii_82575;
+ } else if (hw->mac.type == e1000_82580) {
+ phy->ops.reset = igb_phy_hw_reset;
+ phy->ops.read_reg = igb_read_phy_reg_82580;
+ phy->ops.write_reg = igb_write_phy_reg_82580;
} else {
phy->ops.reset = igb_phy_hw_reset;
phy->ops.read_reg = igb_read_phy_reg_igp;
phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575;
phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state;
break;
+ case I82580_I_PHY_ID:
+ phy->type = e1000_phy_82580;
+ phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580;
+ phy->ops.get_cable_length = igb_get_cable_length_82580;
+ phy->ops.get_phy_info = igb_get_phy_info_82580;
+ break;
default:
return -E1000_ERR_PHY;
}
if (hw->bus.func == 1)
mask = E1000_NVM_CFG_DONE_PORT_1;
+ else if (hw->bus.func == E1000_FUNC_2)
+ mask = E1000_NVM_CFG_DONE_PORT_2;
+ else if (hw->bus.func == E1000_FUNC_3)
+ mask = E1000_NVM_CFG_DONE_PORT_3;
while (timeout) {
if (rd32(E1000_EEMNGCTL) & mask)
if (hw->bus.func == E1000_FUNC_0)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ else if (hw->mac.type == e1000_82580)
+ hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
+ NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
+ &eeprom_data);
else if (hw->bus.func == E1000_FUNC_1)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
goto out;
if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
+ /* allow time for SFP cage time to power up phy */
+ msleep(300);
+
ret_val = hw->phy.ops.reset(hw);
if (ret_val) {
hw_dbg("Error resetting the PHY.\n");
case e1000_phy_igp_3:
ret_val = igb_copper_link_setup_igp(hw);
break;
+ case e1000_phy_82580:
+ ret_val = igb_copper_link_setup_82580(hw);
+ break;
default:
ret_val = -E1000_ERR_PHY;
break;
**/
static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
- u32 ctrl_reg, reg;
+ u32 ctrl_ext, ctrl_reg, reg;
+ bool pcs_autoneg;
if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
!igb_sgmii_active_82575(hw))
wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
/* power on the sfp cage if present */
- reg = rd32(E1000_CTRL_EXT);
- reg &= ~E1000_CTRL_EXT_SDP3_DATA;
- wr32(E1000_CTRL_EXT, reg);
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+ wr32(E1000_CTRL_EXT, ctrl_ext);
ctrl_reg = rd32(E1000_CTRL);
ctrl_reg |= E1000_CTRL_SLU;
reg = rd32(E1000_PCS_LCTL);
- if (igb_sgmii_active_82575(hw)) {
- /* allow time for SFP cage to power up phy */
- msleep(300);
+ /* default pcs_autoneg to the same setting as mac autoneg */
+ pcs_autoneg = hw->mac.autoneg;
- /* AN time out should be disabled for SGMII mode */
+ switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
+ case E1000_CTRL_EXT_LINK_MODE_SGMII:
+ /* sgmii mode lets the phy handle forcing speed/duplex */
+ pcs_autoneg = true;
+ /* autoneg time out should be disabled for SGMII mode */
reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
- } else {
+ break;
+ case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
+ /* disable PCS autoneg and support parallel detect only */
+ pcs_autoneg = false;
+ default:
+ /*
+ * non-SGMII modes only supports a speed of 1000/Full for the
+ * link so it is best to just force the MAC and let the pcs
+ * link either autoneg or be forced to 1000/Full
+ */
ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
E1000_CTRL_FD | E1000_CTRL_FRCDPX;
+
+ /* set speed of 1000/Full if speed/duplex is forced */
+ reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL;
+ break;
}
wr32(E1000_CTRL, ctrl_reg);
* mode that will be compatible with older link partners and switches.
* However, both are supported by the hardware and some drivers/tools.
*/
-
reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
*/
reg |= E1000_PCS_LCTL_FORCE_FCTRL;
- /*
- * we always set sgmii to autoneg since it is the phy that will be
- * forcing the link and the serdes is just a go-between
- */
- if (hw->mac.autoneg || igb_sgmii_active_82575(hw)) {
+ if (pcs_autoneg) {
/* Set PCS register for autoneg */
- reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
- E1000_PCS_LCTL_FDV_FULL | /* SerDes Full dplx */
- E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
+ reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
- hw_dbg("Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg);
+ hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
} else {
- /* Check for duplex first */
- if (hw->mac.forced_speed_duplex & E1000_ALL_FULL_DUPLEX)
- reg |= E1000_PCS_LCTL_FDV_FULL;
-
- /* No need to check for 1000/full since the spec states that
- * it requires autoneg to be enabled */
- /* Now set speed */
- if (hw->mac.forced_speed_duplex & E1000_ALL_100_SPEED)
- reg |= E1000_PCS_LCTL_FSV_100;
-
- /* Force speed and force link */
- reg |= E1000_PCS_LCTL_FSD |
- E1000_PCS_LCTL_FORCE_LINK |
- E1000_PCS_LCTL_FLV_LINK_UP;
-
- hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg);
+ /* Set PCS register for forced link */
+ reg |= E1000_PCS_LCTL_FSD | /* Force Speed */
+ E1000_PCS_LCTL_FORCE_LINK | /* Force Link */
+ E1000_PCS_LCTL_FLV_LINK_UP; /* Force link value up */
+
+ hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
}
wr32(E1000_PCS_LCTL, reg);
wr32(E1000_VT_CTL, vt_ctl);
}
+/**
+ * igb_read_phy_reg_82580 - Read 82580 MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the MDI control register in the PHY at offset and stores the
+ * information read to data.
+ **/
+static s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ u32 mdicnfg = 0;
+ s32 ret_val;
+
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * We config the phy address in MDICNFG register now. Same bits
+ * as before. The values in MDIC can be written but will be
+ * ignored. This allows us to call the old function after
+ * configuring the PHY address in the new register
+ */
+ mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT);
+ wr32(E1000_MDICNFG, mdicnfg);
+
+ ret_val = igb_read_phy_reg_mdic(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_write_phy_reg_82580 - Write 82580 MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write to register at offset
+ *
+ * Writes data to MDI control register in the PHY at offset.
+ **/
+static s32 igb_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ u32 mdicnfg = 0;
+ s32 ret_val;
+
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * We config the phy address in MDICNFG register now. Same bits
+ * as before. The values in MDIC can be written but will be
+ * ignored. This allows us to call the old function after
+ * configuring the PHY address in the new register
+ */
+ mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT);
+ wr32(E1000_MDICNFG, mdicnfg);
+
+ ret_val = igb_write_phy_reg_mdic(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_reset_hw_82580 - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets function or entire device (all ports, etc.)
+ * to a known state.
+ **/
+static s32 igb_reset_hw_82580(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ /* BH SW mailbox bit in SW_FW_SYNC */
+ u16 swmbsw_mask = E1000_SW_SYNCH_MB;
+ u32 ctrl, icr;
+ bool global_device_reset = hw->dev_spec._82575.global_device_reset;
+
+
+ hw->dev_spec._82575.global_device_reset = false;
+
+ /* Get current control state. */
+ ctrl = rd32(E1000_CTRL);
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = igb_disable_pcie_master(hw);
+ if (ret_val)
+ hw_dbg("PCI-E Master disable polling has failed.\n");
+
+ hw_dbg("Masking off all interrupts\n");
+ wr32(E1000_IMC, 0xffffffff);
+ wr32(E1000_RCTL, 0);
+ wr32(E1000_TCTL, E1000_TCTL_PSP);
+ wrfl();
+
+ msleep(10);
+
+ /* Determine whether or not a global dev reset is requested */
+ if (global_device_reset &&
+ igb_acquire_swfw_sync_82575(hw, swmbsw_mask))
+ global_device_reset = false;
+
+ if (global_device_reset &&
+ !(rd32(E1000_STATUS) & E1000_STAT_DEV_RST_SET))
+ ctrl |= E1000_CTRL_DEV_RST;
+ else
+ ctrl |= E1000_CTRL_RST;
+
+ wr32(E1000_CTRL, ctrl);
+
+ /* Add delay to insure DEV_RST has time to complete */
+ if (global_device_reset)
+ msleep(5);
+
+ ret_val = igb_get_auto_rd_done(hw);
+ if (ret_val) {
+ /*
+ * When auto config read does not complete, do not
+ * return with an error. This can happen in situations
+ * where there is no eeprom and prevents getting link.
+ */
+ hw_dbg("Auto Read Done did not complete\n");
+ }
+
+ /* If EEPROM is not present, run manual init scripts */
+ if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0)
+ igb_reset_init_script_82575(hw);
+
+ /* clear global device reset status bit */
+ wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET);
+
+ /* Clear any pending interrupt events. */
+ wr32(E1000_IMC, 0xffffffff);
+ icr = rd32(E1000_ICR);
+
+ /* Install any alternate MAC address into RAR0 */
+ ret_val = igb_check_alt_mac_addr(hw);
+
+ /* Release semaphore */
+ if (global_device_reset)
+ igb_release_swfw_sync_82575(hw, swmbsw_mask);
+
+ return ret_val;
+}
+
+/**
+ * igb_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size
+ * @data: data received by reading RXPBS register
+ *
+ * The 82580 uses a table based approach for packet buffer allocation sizes.
+ * This function converts the retrieved value into the correct table value
+ * 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7
+ * 0x0 36 72 144 1 2 4 8 16
+ * 0x8 35 70 140 rsv rsv rsv rsv rsv
+ */
+u16 igb_rxpbs_adjust_82580(u32 data)
+{
+ u16 ret_val = 0;
+
+ if (data < E1000_82580_RXPBS_TABLE_SIZE)
+ ret_val = e1000_82580_rxpbs_table[data];
+
+ return ret_val;
+}
+
static struct e1000_mac_operations e1000_mac_ops_82575 = {
- .reset_hw = igb_reset_hw_82575,
.init_hw = igb_init_hw_82575,
.check_for_link = igb_check_for_link_82575,
.rar_set = igb_rar_set,
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff