}
/**
+ * igb_copper_link_setup_82580 - Setup 82580 PHY for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up Carrier-sense on Transmit and downshift values.
+ **/
+s32 igb_copper_link_setup_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+
+
+ if (phy->reset_disable) {
+ ret_val = 0;
+ goto out;
+ }
+
+ if (phy->type == e1000_phy_82580) {
+ ret_val = hw->phy.ops.reset(hw);
+ if (ret_val) {
+ hw_dbg("Error resetting the PHY.\n");
+ goto out;
+ }
+ }
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = phy->ops.read_reg(hw, I82580_CFG_REG, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= I82580_CFG_ASSERT_CRS_ON_TX;
+
+ /* Enable downshift */
+ phy_data |= I82580_CFG_ENABLE_DOWNSHIFT;
+
+ ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Set number of link attempts before downshift */
+ ret_val = phy->ops.read_reg(hw, I82580_CTRL_REG, &phy_data);
+ if (ret_val)
+ goto out;
+ phy_data &= ~I82580_CTRL_DOWNSHIFT_MASK;
+ ret_val = phy->ops.write_reg(hw, I82580_CTRL_REG, phy_data);
+
+out:
+ return ret_val;
+}
+
+/**
* igb_copper_link_setup_m88 - Setup m88 PHY's for copper link
* @hw: pointer to the HW structure
*
return 0;
}
+/**
+ * igb_check_polarity_82580 - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY specific status register.
+ **/
+s32 igb_check_polarity_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & I82580_PHY_STATUS2_REV_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * igb_phy_force_speed_duplex_82580 - Force speed/duplex for I82580 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Waits for link and returns
+ * successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+
+ ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ igb_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. 82580 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX;
+ phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX;
+
+ ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data);
+ if (ret_val)
+ goto out;
+
+ hw_dbg("I82580_PHY_CTRL_2: %X\n", phy_data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ hw_dbg("Waiting for forced speed/duplex link on 82580 phy\n");
+
+ ret_val = igb_phy_has_link(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ hw_dbg("Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = igb_phy_has_link(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_phy_info_82580 - Retrieve I82580 PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Read PHY status to determine if link is up. If link is up, then
+ * set/determine 10base-T extended distance and polarity correction. Read
+ * PHY port status to determine MDI/MDIx and speed. Based on the speed,
+ * determine on the cable length, local and remote receiver.
+ **/
+s32 igb_get_phy_info_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+
+ ret_val = igb_phy_has_link(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ hw_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ phy->polarity_correction = true;
+
+ ret_val = igb_check_polarity_82580(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & I82580_PHY_STATUS2_MDIX) ? true : false;
+
+ if ((data & I82580_PHY_STATUS2_SPEED_MASK) ==
+ I82580_PHY_STATUS2_SPEED_1000MBPS) {
+ ret_val = hw->phy.ops.get_cable_length(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+ } else {
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_cable_length_82580 - Determine cable length for 82580 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Reads the diagnostic status register and verifies result is valid before
+ * placing it in the phy_cable_length field.
+ **/
+s32 igb_get_cable_length_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, length;
+
+
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_DIAG_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ length = (phy_data & I82580_DSTATUS_CABLE_LENGTH) >>
+ I82580_DSTATUS_CABLE_LENGTH_SHIFT;
+
+ if (length == E1000_CABLE_LENGTH_UNDEFINED)
+ ret_val = -E1000_ERR_PHY;
+
+ phy->cable_length = length;
+
+out:
+ return ret_val;
+}
s32 igb_phy_init_script_igp3(struct e1000_hw *hw);
s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
+s32 igb_copper_link_setup_82580(struct e1000_hw *hw);
+s32 igb_check_polarity_82580(struct e1000_hw *hw);
+s32 igb_get_phy_info_82580(struct e1000_hw *hw);
+s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
+s32 igb_get_cable_length_82580(struct e1000_hw *hw);
/* IGP01E1000 Specific Registers */
#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */
#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */
#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
+#define I82580_ADDR_REG 16
+#define I82580_CFG_REG 22
+#define I82580_CFG_ASSERT_CRS_ON_TX (1 << 15)
+#define I82580_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */
+#define I82580_CTRL_REG 23
+#define I82580_CTRL_DOWNSHIFT_MASK (7 << 10)
+
+/* 82580 specific PHY registers */
+#define I82580_PHY_CTRL_2 18
+#define I82580_PHY_LBK_CTRL 19
+#define I82580_PHY_STATUS_2 26
+#define I82580_PHY_DIAG_STATUS 31
+
+/* I82580 PHY Status 2 */
+#define I82580_PHY_STATUS2_REV_POLARITY 0x0400
+#define I82580_PHY_STATUS2_MDIX 0x0800
+#define I82580_PHY_STATUS2_SPEED_MASK 0x0300
+#define I82580_PHY_STATUS2_SPEED_1000MBPS 0x0200
+#define I82580_PHY_STATUS2_SPEED_100MBPS 0x0100
+
+/* I82580 PHY Control 2 */
+#define I82580_PHY_CTRL2_AUTO_MDIX 0x0400
+#define I82580_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
+
+/* I82580 PHY Diagnostics Status */
+#define I82580_DSTATUS_CABLE_LENGTH 0x03FC
+#define I82580_DSTATUS_CABLE_LENGTH_SHIFT 2
/* Enable flexible speed on link-up */
#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff