sl82c105: remove no longer needed debugging code

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

diff --git a/drivers/ide/sl82c105.c b/drivers/ide/sl82c105.c
index d698da4..3c2bbf0 100644 (file)
--- a/drivers/ide/sl82c105.c
+++ b/drivers/ide/sl82c105.c
@@ -24,13 +24,6 @@
 
 #define DRV_NAME "sl82c105"
 
-#undef DEBUG
-
-#ifdef DEBUG
-#define DBG(arg) printk arg
-#else
-#define DBG(fmt,...)
-#endif
 /*
  * SL82C105 PCI config register 0x40 bits.
  */
@@ -104,9 +97,6 @@ static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed)
        unsigned long timings = (unsigned long)ide_get_drivedata(drive);
        u16 drv_ctrl;
 
-       DBG(("sl82c105_tune_chipset(drive:%s, speed:%s)\n",
-            drive->name, ide_xfer_verbose(speed)));
-
        drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0];
 
        /*
@@ -196,8 +186,6 @@ static void sl82c105_dma_start(ide_drive_t *drive)
        struct pci_dev *dev     = to_pci_dev(hwif->dev);
        int reg                 = 0x44 + drive->dn * 4;
 
-       DBG(("%s(drive:%s)\n", __func__, drive->name));
-
        pci_write_config_word(dev, reg,
                              (unsigned long)ide_get_drivedata(drive) >> 16);
 
@@ -209,8 +197,6 @@ static void sl82c105_dma_clear(ide_drive_t *drive)
 {
        struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
 
-       DBG(("sl82c105_dma_clear(drive:%s)\n", drive->name));
-
        sl82c105_reset_host(dev);
 }
 
@@ -218,11 +204,7 @@ static int sl82c105_dma_end(ide_drive_t *drive)
 {
        struct pci_dev *dev     = to_pci_dev(drive->hwif->dev);
        int reg                 = 0x44 + drive->dn * 4;
-       int ret;
-
-       DBG(("%s(drive:%s)\n", __func__, drive->name));
-
-       ret = ide_dma_end(drive);
+       int ret                 = ide_dma_end(drive);
 
        pci_write_config_word(dev, reg,
                              (unsigned long)ide_get_drivedata(drive));
@@ -239,8 +221,6 @@ static void sl82c105_resetproc(ide_drive_t *drive)
        struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
        u32 val;
 
-       DBG(("sl82c105_resetproc(drive:%s)\n", drive->name));
-
        pci_read_config_dword(dev, 0x40, &val);
        val |= (CTRL_P1F16 | CTRL_P0F16);
        pci_write_config_dword(dev, 0x40, val);
@@ -291,8 +271,6 @@ static int init_chipset_sl82c105(struct pci_dev *dev)
 {
        u32 val;
 
-       DBG(("init_chipset_sl82c105()\n"));
-
        pci_read_config_dword(dev, 0x40, &val);
        val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
        pci_write_config_dword(dev, 0x40, val);