[PATCH] dvb: bt8xx: updated documentation

updated documentation (Manu Abraham)

Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

diff --git a/Documentation/dvb/bt8xx.txt b/Documentation/dvb/bt8xx.txt
index d84df80..d64430b 100644 (file)
--- a/Documentation/dvb/bt8xx.txt
+++ b/Documentation/dvb/bt8xx.txt
@@ -35,45 +35,35 @@ TwinHan (dst) are loaded automatically by the dvb-bt8xx device driver.
    $ modprobe bttv (normally bttv is being loaded automatically by kmod)
    $ modprobe dvb-bt8xx (or just place dvb-bt8xx in /etc/modules for automatic loading)
 
-3b) TwinHan
------------
+
+3b) TwinHan and Clones
+--------------------------
 
    $ modprobe bttv i2c_hw=1 card=0x71
    $ modprobe dvb-bt8xx
    $ modprobe dst
 
-The value 0x71 will override the PCI type detection for dvb-bt8xx, which 
-is necessary for TwinHan cards.#
+The value 0x71 will override the PCI type detection for dvb-bt8xx,
+which  is necessary for TwinHan cards.
 
-If you're having an older card (blue color circuit) and card=0x71 locks your
-machine, try using 0x68, too. If that does not work, ask on the DVB mailing list.
+If you're having an older card (blue color circuit) and card=0x71 locks
+your machine, try using 0x68, too. If that does not work, ask on the
+mailing list.
 
-The DST module takes a couple of useful parameters, in case the
-dst drivers fails to detect your type of card correctly.
+The DST module takes a couple of useful parameters.
 
-dst_type takes values 0 (satellite), 1 (terrestial TV), 2 (cable).
+verbose takes values 0 to 5. These values control the verbosity level.
 
-dst_type_flags takes bit combined values:
-1 = new tuner type packets. You can use this if your card is detected
-    and you have debug and you continually see the tuner packets not
-    working (make sure not a basic problem like dish alignment etc.)
+debug takes values 0 and 1. You can either disable or enable debugging.
 
-2 = TS 204. If your card tunes OK, but the picture is terrible, seemingly
-    breaking up in one half continually, and crc fails a lot, then
-    this is worth a try (or trying to turn off)
+dst_addons takes values 0 and 0x20. A value of 0 means it is a FTA card.
+0x20 means it has a Conditional Access slot.
 
-4 = has symdiv. Some cards, mostly without new tuner packets, require
-    a symbol division algorithm. Doesn't apply to terrestial TV.
-
-You can also specify a value to have the autodetected values turned off
-(e.g. 0). The autodected values are determined bythe cards 'response
+The autodected values are determined bythe cards 'response
 string' which you can see in your logs e.g.
 
-dst_check_ci: recognize DST-MOT
-
-or 
+dst_get_device_id: Recognise [DSTMCI]
 
-dst_check_ci: unable to recognize DSTXCI or STXCI
 
 --
-Authors: Richard Walker, Jamie Honan, Michael Hunold
+Authors: Richard Walker, Jamie Honan, Michael Hunold, Manu Abraham