config ATH5K
tristate "Atheros 5xxx wireless cards support"
depends on PCI && MAC80211 && WLAN_80211 && EXPERIMENTAL
- depends on BROKEN
---help---
This module adds support for wireless adapters based on
Atheros 5xxx chipset.
-ath5k-objs = base.o hw.o regdom.o initvals.o phy.o debug.o
+ath5k-objs = base.o hw.o initvals.o phy.o debug.o
obj-$(CONFIG_ATH5K) += ath5k.o
#include <net/mac80211.h>
#include "hw.h"
-#include "regdom.h"
/* PCI IDs */
#define PCI_DEVICE_ID_ATHEROS_AR5210 0x0007 /* AR5210 */
*/
#define MODULATION_TURBO 0x00000080
-enum ath5k_vendor_mode {
- MODE_ATHEROS_TURBO = NUM_IEEE80211_MODES+1,
- MODE_ATHEROS_TURBOG
+enum ath5k_driver_mode {
+ AR5K_MODE_11A = 0,
+ AR5K_MODE_11A_TURBO = 1,
+ AR5K_MODE_11B = 2,
+ AR5K_MODE_11G = 3,
+ AR5K_MODE_11G_TURBO = 4,
+ AR5K_MODE_XR = 0,
+ AR5K_MODE_MAX = 5
};
-/* Number of supported mac80211 enum ieee80211_phymode modes by this driver */
-#define NUM_DRIVER_MODES 3
-
/* adding this flag to rate_code enables short preamble, see ar5212_reg.h */
#define AR5K_SET_SHORT_PREAMBLE 0x04
-#define HAS_SHPREAMBLE(_ix) (rt->rates[_ix].modulation == IEEE80211_RATE_CCK_2)
+#define HAS_SHPREAMBLE(_ix) (rt->rates[_ix].modulation == IEEE80211_RATE_SHORT_PREAMBLE)
#define SHPREAMBLE_FLAG(_ix) (HAS_SHPREAMBLE(_ix) ? AR5K_SET_SHORT_PREAMBLE : 0)
/****************\
* Used internaly in OpenHAL (ar5211.c/ar5212.c
* for reset_tx_queue). Also see struct struct ieee80211_channel.
*/
-#define IS_CHAN_XR(_c) ((_c.val & CHANNEL_XR) != 0)
-#define IS_CHAN_B(_c) ((_c.val & CHANNEL_B) != 0)
+#define IS_CHAN_XR(_c) ((_c.hw_value & CHANNEL_XR) != 0)
+#define IS_CHAN_B(_c) ((_c.hw_value & CHANNEL_B) != 0)
/*
* The following structure will be used to map 2GHz channels to
/**
* struct ath5k_rate - rate structure
- * @valid: is this a valid rate for the current mode
+ * @valid: is this a valid rate for rate control (remove)
* @modulation: respective mac80211 modulation
* @rate_kbps: rate in kbit/s
* @rate_code: hardware rate value, used in &struct ath5k_desc, on RX on
/*
* Rate tables...
+ * TODO: CLEAN THIS !!!
*/
#define AR5K_RATES_11A { 8, { \
255, 255, 255, 255, 255, 255, 255, 255, 6, 4, 2, 0, \
7, 5, 3, 1, 255, 255, 255, 255, 255, 255, 255, 255, \
255, 255, 255, 255, 255, 255, 255, 255 }, { \
- { 1, IEEE80211_RATE_OFDM, 6000, 11, 140, 0 }, \
- { 1, IEEE80211_RATE_OFDM, 9000, 15, 18, 0 }, \
- { 1, IEEE80211_RATE_OFDM, 12000, 10, 152, 2 }, \
- { 1, IEEE80211_RATE_OFDM, 18000, 14, 36, 2 }, \
- { 1, IEEE80211_RATE_OFDM, 24000, 9, 176, 4 }, \
- { 1, IEEE80211_RATE_OFDM, 36000, 13, 72, 4 }, \
- { 1, IEEE80211_RATE_OFDM, 48000, 8, 96, 4 }, \
- { 1, IEEE80211_RATE_OFDM, 54000, 12, 108, 4 } } \
+ { 1, 0, 6000, 11, 140, 0 }, \
+ { 1, 0, 9000, 15, 18, 0 }, \
+ { 1, 0, 12000, 10, 152, 2 }, \
+ { 1, 0, 18000, 14, 36, 2 }, \
+ { 1, 0, 24000, 9, 176, 4 }, \
+ { 1, 0, 36000, 13, 72, 4 }, \
+ { 1, 0, 48000, 8, 96, 4 }, \
+ { 1, 0, 54000, 12, 108, 4 } } \
}
#define AR5K_RATES_11B { 4, { \
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, \
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, \
3, 2, 1, 0, 255, 255, 255, 255 }, { \
- { 1, IEEE80211_RATE_CCK, 1000, 27, 130, 0 }, \
- { 1, IEEE80211_RATE_CCK_2, 2000, 26, 132, 1 }, \
- { 1, IEEE80211_RATE_CCK_2, 5500, 25, 139, 1 }, \
- { 1, IEEE80211_RATE_CCK_2, 11000, 24, 150, 1 } } \
+ { 1, 0, 1000, 27, 130, 0 }, \
+ { 1, IEEE80211_RATE_SHORT_PREAMBLE, 2000, 26, 132, 1 }, \
+ { 1, IEEE80211_RATE_SHORT_PREAMBLE, 5500, 25, 139, 1 }, \
+ { 1, IEEE80211_RATE_SHORT_PREAMBLE, 11000, 24, 150, 1 } } \
}
#define AR5K_RATES_11G { 12, { \
255, 255, 255, 255, 255, 255, 255, 255, 10, 8, 6, 4, \
11, 9, 7, 5, 255, 255, 255, 255, 255, 255, 255, 255, \
3, 2, 1, 0, 255, 255, 255, 255 }, { \
- { 1, IEEE80211_RATE_CCK, 1000, 27, 2, 0 }, \
- { 1, IEEE80211_RATE_CCK_2, 2000, 26, 4, 1 }, \
- { 1, IEEE80211_RATE_CCK_2, 5500, 25, 11, 1 }, \
- { 1, IEEE80211_RATE_CCK_2, 11000, 24, 22, 1 }, \
- { 0, IEEE80211_RATE_OFDM, 6000, 11, 12, 4 }, \
- { 0, IEEE80211_RATE_OFDM, 9000, 15, 18, 4 }, \
- { 1, IEEE80211_RATE_OFDM, 12000, 10, 24, 6 }, \
- { 1, IEEE80211_RATE_OFDM, 18000, 14, 36, 6 }, \
- { 1, IEEE80211_RATE_OFDM, 24000, 9, 48, 8 }, \
- { 1, IEEE80211_RATE_OFDM, 36000, 13, 72, 8 }, \
- { 1, IEEE80211_RATE_OFDM, 48000, 8, 96, 8 }, \
- { 1, IEEE80211_RATE_OFDM, 54000, 12, 108, 8 } } \
+ { 1, 0, 1000, 27, 2, 0 }, \
+ { 1, IEEE80211_RATE_SHORT_PREAMBLE, 2000, 26, 4, 1 }, \
+ { 1, IEEE80211_RATE_SHORT_PREAMBLE, 5500, 25, 11, 1 }, \
+ { 1, IEEE80211_RATE_SHORT_PREAMBLE, 11000, 24, 22, 1 }, \
+ { 0, 0, 6000, 11, 12, 4 }, \
+ { 0, 0, 9000, 15, 18, 4 }, \
+ { 1, 0, 12000, 10, 24, 6 }, \
+ { 1, 0, 18000, 14, 36, 6 }, \
+ { 1, 0, 24000, 9, 48, 8 }, \
+ { 1, 0, 36000, 13, 72, 8 }, \
+ { 1, 0, 48000, 8, 96, 8 }, \
+ { 1, 0, 54000, 12, 108, 8 } } \
}
#define AR5K_RATES_TURBO { 8, { \
{ 1, MODULATION_XR, 1000, 2, 139, 1 }, \
{ 1, MODULATION_XR, 2000, 6, 150, 2 }, \
{ 1, MODULATION_XR, 3000, 1, 150, 3 }, \
- { 1, IEEE80211_RATE_OFDM, 6000, 11, 140, 4 }, \
- { 1, IEEE80211_RATE_OFDM, 9000, 15, 18, 4 }, \
- { 1, IEEE80211_RATE_OFDM, 12000, 10, 152, 6 }, \
- { 1, IEEE80211_RATE_OFDM, 18000, 14, 36, 6 }, \
- { 1, IEEE80211_RATE_OFDM, 24000, 9, 176, 8 }, \
- { 1, IEEE80211_RATE_OFDM, 36000, 13, 72, 8 }, \
- { 1, IEEE80211_RATE_OFDM, 48000, 8, 96, 8 }, \
- { 1, IEEE80211_RATE_OFDM, 54000, 12, 108, 8 } } \
+ { 1, 0, 6000, 11, 140, 4 }, \
+ { 1, 0, 9000, 15, 18, 4 }, \
+ { 1, 0, 12000, 10, 152, 6 }, \
+ { 1, 0, 18000, 14, 36, 6 }, \
+ { 1, 0, 24000, 9, 176, 8 }, \
+ { 1, 0, 36000, 13, 72, 8 }, \
+ { 1, 0, 48000, 8, 96, 8 }, \
+ { 1, 0, 54000, 12, 108, 8 } } \
}
/*
* Supported PHY modes
* (ie. CHANNEL_A, CHANNEL_B, ...)
*/
- DECLARE_BITMAP(cap_mode, NUM_DRIVER_MODES);
+ DECLARE_BITMAP(cap_mode, AR5K_MODE_MAX);
/*
* Frequency range (without regulation restrictions)
} cap_range;
/*
- * Active regulation domain settings
- */
- struct {
- enum ath5k_regdom reg_current;
- enum ath5k_regdom reg_hw;
- } cap_regdomain;
-
- /*
* Values stored in the EEPROM (some of them...)
*/
struct ath5k_eeprom_info cap_eeprom;
extern u32 ath5k_hw_get_gpio(struct ath5k_hw *ah, u32 gpio);
extern int ath5k_hw_set_gpio(struct ath5k_hw *ah, u32 gpio, u32 val);
extern void ath5k_hw_set_gpio_intr(struct ath5k_hw *ah, unsigned int gpio, u32 interrupt_level);
-/* Regulatory Domain/Channels Setup */
-extern u16 ath5k_get_regdomain(struct ath5k_hw *ah);
/* Misc functions */
extern int ath5k_hw_get_capability(struct ath5k_hw *ah, enum ath5k_capability_type cap_type, u32 capability, u32 *result);
static void ath5k_setcurmode(struct ath5k_softc *sc,
unsigned int mode);
static void ath5k_mode_setup(struct ath5k_softc *sc);
+static void ath5k_set_total_hw_rates(struct ath5k_softc *sc);
+
/* Descriptor setup */
static int ath5k_desc_alloc(struct ath5k_softc *sc,
struct pci_dev *pdev);
/* Single chip radio (!RF5111) */
if(sc->ah->ah_radio_5ghz_revision && !sc->ah->ah_radio_2ghz_revision) {
/* No 5GHz support -> report 2GHz radio */
- if(!test_bit(MODE_IEEE80211A, sc->ah->ah_capabilities.cap_mode)){
+ if(!test_bit(AR5K_MODE_11A, sc->ah->ah_capabilities.cap_mode)){
ATH5K_INFO(sc, "RF%s 2GHz radio found (0x%x)\n",
ath5k_chip_name(AR5K_VERSION_RAD,sc->ah->ah_radio_5ghz_revision),
sc->ah->ah_radio_5ghz_revision);
/* No 2GHz support (5110 and some 5Ghz only cards) -> report 5Ghz radio */
- } else if(!test_bit(MODE_IEEE80211B, sc->ah->ah_capabilities.cap_mode)){
+ } else if(!test_bit(AR5K_MODE_11B, sc->ah->ah_capabilities.cap_mode)){
ATH5K_INFO(sc, "RF%s 5GHz radio found (0x%x)\n",
ath5k_chip_name(AR5K_VERSION_RAD,sc->ah->ah_radio_5ghz_revision),
sc->ah->ah_radio_5ghz_revision);
goto err;
}
+ /* Set *_rates so we can map hw rate index */
+ ath5k_set_total_hw_rates(sc);
+
/* NB: setup here so ath5k_rate_update is happy */
- if (test_bit(MODE_IEEE80211A, ah->ah_modes))
- ath5k_setcurmode(sc, MODE_IEEE80211A);
+ if (test_bit(AR5K_MODE_11A, ah->ah_modes))
+ ath5k_setcurmode(sc, AR5K_MODE_11A);
else
- ath5k_setcurmode(sc, MODE_IEEE80211B);
+ ath5k_setcurmode(sc, AR5K_MODE_11B);
/*
* Allocate tx+rx descriptors and populate the lists.
return 0;
for (i = 0, count = 0; i < rt->rate_count && max > 0; i++) {
- if (!rt->rates[i].valid)
- continue;
- rates->rate = rt->rates[i].rate_kbps / 100;
- rates->val = rt->rates[i].rate_code;
- rates->flags = rt->rates[i].modulation;
- rates++;
+ rates[count].bitrate = rt->rates[i].rate_kbps / 100;
+ rates[count].hw_value = rt->rates[i].rate_code;
+ rates[count].flags = rt->rates[i].modulation;
count++;
max--;
}
unsigned int mode,
unsigned int max)
{
- static const struct { unsigned int mode, mask, chan; } map[] = {
- [MODE_IEEE80211A] = { CHANNEL_OFDM, CHANNEL_OFDM | CHANNEL_TURBO, CHANNEL_A },
- [MODE_ATHEROS_TURBO] = { CHANNEL_OFDM|CHANNEL_TURBO, CHANNEL_OFDM | CHANNEL_TURBO, CHANNEL_T },
- [MODE_IEEE80211B] = { CHANNEL_CCK, CHANNEL_CCK, CHANNEL_B },
- [MODE_IEEE80211G] = { CHANNEL_OFDM, CHANNEL_OFDM, CHANNEL_G },
- [MODE_ATHEROS_TURBOG] = { CHANNEL_OFDM | CHANNEL_TURBO, CHANNEL_OFDM | CHANNEL_TURBO, CHANNEL_TG },
- };
- static const struct ath5k_regchannel chans_2ghz[] =
- IEEE80211_CHANNELS_2GHZ;
- static const struct ath5k_regchannel chans_5ghz[] =
- IEEE80211_CHANNELS_5GHZ;
- const struct ath5k_regchannel *chans;
- enum ath5k_regdom dmn;
- unsigned int i, count, size, chfreq, all, f, ch;
+ unsigned int i, count, size, chfreq, freq, ch;
if (!test_bit(mode, ah->ah_modes))
return 0;
- all = ah->ah_regdomain == DMN_DEFAULT || CHAN_DEBUG == 1;
-
switch (mode) {
- case MODE_IEEE80211A:
- case MODE_ATHEROS_TURBO:
+ case AR5K_MODE_11A:
+ case AR5K_MODE_11A_TURBO:
/* 1..220, but 2GHz frequencies are filtered by check_channel */
- size = all ? 220 : ARRAY_SIZE(chans_5ghz);
- chans = chans_5ghz;
- dmn = ath5k_regdom2flag(ah->ah_regdomain,
- IEEE80211_CHANNELS_5GHZ_MIN);
+ size = 220 ;
chfreq = CHANNEL_5GHZ;
break;
- case MODE_IEEE80211B:
- case MODE_IEEE80211G:
- case MODE_ATHEROS_TURBOG:
- size = all ? 26 : ARRAY_SIZE(chans_2ghz);
- chans = chans_2ghz;
- dmn = ath5k_regdom2flag(ah->ah_regdomain,
- IEEE80211_CHANNELS_2GHZ_MIN);
+ case AR5K_MODE_11B:
+ case AR5K_MODE_11G:
+ case AR5K_MODE_11G_TURBO:
+ size = 26;
chfreq = CHANNEL_2GHZ;
break;
default:
}
for (i = 0, count = 0; i < size && max > 0; i++) {
- ch = all ? i + 1 : chans[i].chan;
- f = ath5k_ieee2mhz(ch);
- /* Check if channel is supported by the chipset */
- if (!ath5k_channel_ok(ah, f, chfreq))
- continue;
+ ch = i + 1 ;
+ freq = ath5k_ieee2mhz(ch);
- /* Match regulation domain */
- if (!all && !(IEEE80211_DMN(chans[i].domain) &
- IEEE80211_DMN(dmn)))
+ /* Check if channel is supported by the chipset */
+ if (!ath5k_channel_ok(ah, freq, chfreq))
continue;
- if (!all && (chans[i].mode & map[mode].mask) != map[mode].mode)
- continue;
+ /* Write channel info and increment counter */
+ channels[count].center_freq = freq;
+
+ if((mode == AR5K_MODE_11A) ||
+ (mode == AR5K_MODE_11G)){
+ channels[count].hw_value = chfreq|CHANNEL_OFDM;
+ } else if((mode == AR5K_MODE_11A_TURBO) ||
+ (mode == AR5K_MODE_11G_TURBO)){
+ channels[count].hw_value = chfreq|CHANNEL_OFDM|CHANNEL_TURBO;
+ }if(mode == AR5K_MODE_11B) {
+ channels[count].hw_value = CHANNEL_B;
+ }
- /* Write channel and increment counter */
- channels->chan = ch;
- channels->freq = f;
- channels->val = map[mode].chan;
- channels++;
count++;
max--;
}
return count;
}
-/* Only tries to register modes our EEPROM says it can support */
-#define REGISTER_MODE(m) do { \
- ret = ath5k_register_mode(hw, m); \
- if (ret) \
- return ret; \
-} while (0) \
-
-static inline int
-ath5k_register_mode(struct ieee80211_hw *hw, u8 m)
+static int
+ath5k_getchannels(struct ieee80211_hw *hw)
{
struct ath5k_softc *sc = hw->priv;
- struct ieee80211_hw_mode *modes = sc->modes;
- unsigned int i;
- int ret;
+ struct ath5k_hw *ah = sc->ah;
+ struct ieee80211_supported_band *sbands = sc->sbands;
+ const struct ath5k_rate_table *hw_rates;
+ unsigned int max_r, max_c, count_r, count_c;
+ int mode2g = AR5K_MODE_11G;
- if (!test_bit(m, sc->ah->ah_capabilities.cap_mode))
- return 0;
+ BUILD_BUG_ON(ARRAY_SIZE(sc->sbands) < IEEE80211_NUM_BANDS);
- for (i = 0; i < NUM_DRIVER_MODES; i++) {
- if (modes[i].mode != m || !modes[i].num_channels)
- continue;
- ret = ieee80211_register_hwmode(hw, &modes[i]);
- if (ret) {
- ATH5K_ERR(sc, "can't register hwmode %u\n", m);
- return ret;
+ max_r = ARRAY_SIZE(sc->rates);
+ max_c = ARRAY_SIZE(sc->channels);
+ count_r = count_c = 0;
+
+ /* 2GHz band */
+ if(!test_bit(AR5K_MODE_11G, sc->ah->ah_capabilities.cap_mode)){
+ mode2g = AR5K_MODE_11B;
+ if(!test_bit(AR5K_MODE_11B, sc->ah->ah_capabilities.cap_mode)){
+ mode2g = -1;
}
- return 0;
}
- BUG();
-}
-static int
-ath5k_getchannels(struct ieee80211_hw *hw)
-{
- struct ath5k_softc *sc = hw->priv;
- struct ath5k_hw *ah = sc->ah;
- struct ieee80211_hw_mode *modes = sc->modes;
- unsigned int i, max_r, max_c;
- int ret;
+ if(mode2g > 0){
+ struct ieee80211_supported_band *sband = &sbands[IEEE80211_BAND_2GHZ];
- BUILD_BUG_ON(ARRAY_SIZE(sc->modes) < 3);
+ sband->bitrates = sc->rates;
+ sband->channels = sc->channels;
- /* The order here does not matter */
- modes[0].mode = MODE_IEEE80211G;
- modes[1].mode = MODE_IEEE80211B;
- modes[2].mode = MODE_IEEE80211A;
+ sband->band = IEEE80211_BAND_2GHZ;
+ sband->n_channels = ath5k_copy_channels(ah, sband->channels,
+ mode2g, max_c);
- max_r = ARRAY_SIZE(sc->rates);
- max_c = ARRAY_SIZE(sc->channels);
+ hw_rates = ath5k_hw_get_rate_table(ah, mode2g);
+ sband->n_bitrates = ath5k_copy_rates(sband->bitrates,
+ hw_rates,max_r);
- for (i = 0; i < NUM_DRIVER_MODES; i++) {
- struct ieee80211_hw_mode *mode = &modes[i];
- const struct ath5k_rate_table *hw_rates;
+ count_c = sband->n_channels;
+ count_r = sband->n_bitrates;
- if (i == 0) {
- modes[0].rates = sc->rates;
- modes->channels = sc->channels;
- } else {
- struct ieee80211_hw_mode *prev_mode = &modes[i-1];
- int prev_num_r = prev_mode->num_rates;
- int prev_num_c = prev_mode->num_channels;
- mode->rates = &prev_mode->rates[prev_num_r];
- mode->channels = &prev_mode->channels[prev_num_c];
- }
+ hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband;
+
+ max_r -= count_r;
+ max_c -= count_c;
- hw_rates = ath5k_hw_get_rate_table(ah, mode->mode);
- mode->num_rates = ath5k_copy_rates(mode->rates, hw_rates,
- max_r);
- mode->num_channels = ath5k_copy_channels(ah, mode->channels,
- mode->mode, max_c);
- max_r -= mode->num_rates;
- max_c -= mode->num_channels;
}
- /* We try to register all modes this driver supports. We don't bother
- * with MODE_IEEE80211B for AR5212 as MODE_IEEE80211G already accounts
- * for that as per mac80211. Then, REGISTER_MODE() will will actually
- * check the eeprom reading for more reliable capability information.
- * Order matters here as per mac80211's latest preference. This will
- * all hopefullly soon go away. */
+ /* 5GHz band */
- REGISTER_MODE(MODE_IEEE80211G);
- if (ah->ah_version != AR5K_AR5212)
- REGISTER_MODE(MODE_IEEE80211B);
- REGISTER_MODE(MODE_IEEE80211A);
+ if(test_bit(AR5K_MODE_11A, sc->ah->ah_capabilities.cap_mode)){
+ struct ieee80211_supported_band *sband = &sbands[IEEE80211_BAND_5GHZ];
- ath5k_debug_dump_modes(sc, modes);
+ sband->bitrates = &sc->rates[count_r];
+ sband->channels = &sc->channels[count_c];
- return ret;
+ sband->band = IEEE80211_BAND_5GHZ;
+ sband->n_channels = ath5k_copy_channels(ah, sband->channels,
+ AR5K_MODE_11A, max_c);
+
+ hw_rates = ath5k_hw_get_rate_table(ah, AR5K_MODE_11A);
+ sband->n_bitrates = ath5k_copy_rates(sband->bitrates,
+ hw_rates,max_r);
+
+ hw->wiphy->bands[IEEE80211_BAND_5GHZ] = sband;
+ }
+
+/* FIXME: ath5k_debug_dump_modes(sc, modes); */
+
+ return 0;
}
/*
struct ath5k_hw *ah = sc->ah;
int ret;
- ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "%u (%u MHz) -> %u (%u MHz)\n",
- sc->curchan->chan, sc->curchan->freq,
- chan->chan, chan->freq);
+ ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "(%u MHz) -> (%u MHz)\n",
+ sc->curchan->center_freq, chan->center_freq);
+
+ if (chan->center_freq != sc->curchan->center_freq ||
+ chan->hw_value != sc->curchan->hw_value) {
+
+ sc->curchan = chan;
+ sc->curband = &sc->sbands[chan->band];
- if (chan->freq != sc->curchan->freq || chan->val != sc->curchan->val) {
/*
* To switch channels clear any pending DMA operations;
* wait long enough for the RX fifo to drain, reset the
ath5k_hw_set_intr(ah, 0); /* disable interrupts */
ath5k_txq_cleanup(sc); /* clear pending tx frames */
ath5k_rx_stop(sc); /* turn off frame recv */
- ret = ath5k_hw_reset(ah, sc->opmode, chan, true);
+ ret = ath5k_hw_reset(ah, sc->opmode, sc->curchan, true);
if (ret) {
- ATH5K_ERR(sc, "%s: unable to reset channel %u "
- "(%u Mhz)\n", __func__, chan->chan, chan->freq);
+ ATH5K_ERR(sc, "%s: unable to reset channel "
+ "(%u Mhz)\n", __func__, chan->center_freq);
return ret;
}
- sc->curchan = chan;
+
ath5k_hw_set_txpower_limit(sc->ah, 0);
/*
return 0;
}
+/*
+ * TODO: CLEAN THIS !!!
+ */
static void
ath5k_setcurmode(struct ath5k_softc *sc, unsigned int mode)
{
continue;
}
sc->hwmap[i].txflags = IEEE80211_RADIOTAP_F_DATAPAD;
- if (SHPREAMBLE_FLAG(ix) || rt->rates[ix].modulation ==
- IEEE80211_RATE_OFDM)
- sc->hwmap[i].txflags |=
- IEEE80211_RADIOTAP_F_SHORTPRE;
/* receive frames include FCS */
sc->hwmap[i].rxflags = sc->hwmap[i].txflags |
IEEE80211_RADIOTAP_F_FCS;
}
sc->curmode = mode;
+
+ if(mode == AR5K_MODE_11A){
+ sc->curband = &sc->sbands[IEEE80211_BAND_5GHZ];
+ } else {
+ sc->curband = &sc->sbands[IEEE80211_BAND_2GHZ];
+ }
}
static void
ATH5K_DBG(sc, ATH5K_DEBUG_MODE, "RX filter 0x%x\n", rfilt);
}
+/*
+ * Match the hw provided rate index (through descriptors)
+ * to an index for sc->curband->bitrates, so it can be used
+ * by the stack.
+ *
+ * This one is a little bit tricky but i think i'm right
+ * about this...
+ *
+ * We have 4 rate tables in the following order:
+ * XR (4 rates)
+ * 802.11a (8 rates)
+ * 802.11b (4 rates)
+ * 802.11g (12 rates)
+ * that make the hw rate table.
+ *
+ * Lets take a 5211 for example that supports a and b modes only.
+ * First comes the 802.11a table and then 802.11b (total 12 rates).
+ * When hw returns eg. 11 it points to the last 802.11b rate (11Mbit),
+ * if it returns 2 it points to the second 802.11a rate etc.
+ *
+ * Same goes for 5212 who has xr/a/b/g support (total 28 rates).
+ * First comes the XR table, then 802.11a, 802.11b and 802.11g.
+ * When hw returns eg. 27 it points to the last 802.11g rate (54Mbits) etc
+ */
+static void
+ath5k_set_total_hw_rates(struct ath5k_softc *sc){
+
+ struct ath5k_hw *ah = sc->ah;
+
+ if(test_bit(AR5K_MODE_11A, ah->ah_modes))
+ sc->a_rates = 8;
+
+ if(test_bit(AR5K_MODE_11B, ah->ah_modes))
+ sc->b_rates = 4;
+
+ if(test_bit(AR5K_MODE_11G, ah->ah_modes))
+ sc->g_rates = 12;
+
+ /* XXX: Need to see what what happens when
+ xr disable bits in eeprom are set */
+ if(ah->ah_version >= AR5K_AR5212)
+ sc->xr_rates = 4;
+
+}
+
+static inline int
+ath5k_hw_to_driver_rix(struct ath5k_softc *sc, int hw_rix){
+
+ int mac80211_rix;
+
+ if(sc->curband->band == IEEE80211_BAND_2GHZ){
+ /* We setup a g ratetable for both b/g modes */
+ mac80211_rix = hw_rix - sc->b_rates - sc->a_rates - sc->xr_rates;
+ } else {
+ mac80211_rix = hw_rix - sc->xr_rates;
+ }
+
+ /* Something went wrong, fallback to basic rate for this band */
+ if((mac80211_rix >= sc->curband->n_bitrates) ||
+ (mac80211_rix <= 0 )){
+ mac80211_rix = 1;
+ }
+
+ return mac80211_rix;
+}
+
ret = ah->ah_setup_tx_desc(ah, ds, pktlen,
ieee80211_get_hdrlen_from_skb(skb), AR5K_PKT_TYPE_NORMAL,
- (ctl->power_level * 2), ctl->tx_rate, ctl->retry_limit, keyidx, 0, flags, 0, 0);
+ (sc->power_level * 2), ctl->tx_rate->hw_value, ctl->retry_limit, keyidx, 0, flags, 0, 0);
if (ret)
goto err_unmap;
rxs.mactime = ath5k_extend_tsf(sc->ah, ds->ds_rxstat.rs_tstamp);
rxs.flag |= RX_FLAG_TSFT;
- rxs.freq = sc->curchan->freq;
- rxs.channel = sc->curchan->chan;
- rxs.phymode = sc->curmode;
+ rxs.freq = sc->curchan->center_freq;
+ rxs.band = sc->curband->band;
/*
* signal quality:
rxs.signal = ds->ds_rxstat.rs_rssi * 100 / 64;
rxs.antenna = ds->ds_rxstat.rs_antenna;
- rxs.rate = ds->ds_rxstat.rs_rate;
+ rxs.rate_idx = ath5k_hw_to_driver_rix(sc,ds->ds_rxstat.rs_rate);
rxs.flag |= ath5k_rx_decrypted(sc, ds, skb);
ath5k_debug_dump_skb(sc, skb, "RX ", 0);
ds->ds_data = bf->skbaddr;
ret = ah->ah_setup_tx_desc(ah, ds, skb->len,
ieee80211_get_hdrlen_from_skb(skb),
- AR5K_PKT_TYPE_BEACON, (ctl->power_level * 2), ctl->tx_rate, 1,
+ AR5K_PKT_TYPE_BEACON, (sc->power_level * 2), ctl->tx_rate->hw_value, 1,
AR5K_TXKEYIX_INVALID, antenna, flags, 0, 0);
if (ret)
goto err_unmap;
* be followed by initialization of the appropriate bits
* and then setup of the interrupt mask.
*/
- sc->curchan = sc->hw->conf.chan;
+ sc->curchan = sc->hw->conf.channel;
+ sc->curband = &sc->sbands[sc->curchan->band];
ret = ath5k_hw_reset(sc->ah, sc->opmode, sc->curchan, false);
if (ret) {
ATH5K_ERR(sc, "unable to reset hardware: %d\n", ret);
struct ath5k_hw *ah = sc->ah;
ATH5K_DBG(sc, ATH5K_DEBUG_CALIBRATE, "channel %u/%x\n",
- sc->curchan->chan, sc->curchan->val);
+ ieee80211_frequency_to_channel(sc->curchan->center_freq), sc->curchan->hw_value);
if (ath5k_hw_get_rf_gain(ah) == AR5K_RFGAIN_NEED_CHANGE) {
/*
}
if (ath5k_hw_phy_calibrate(ah, sc->curchan))
ATH5K_ERR(sc, "calibration of channel %u failed\n",
- sc->curchan->chan);
+ ieee80211_frequency_to_channel(sc->curchan->center_freq));
mod_timer(&sc->calib_tim, round_jiffies(jiffies +
msecs_to_jiffies(ath5k_calinterval * 1000)));
memmove(skb->data, skb->data+pad, hdrlen);
}
- sc->led_txrate = ctl->tx_rate;
+ sc->led_txrate = ctl->tx_rate->hw_value;
spin_lock_irqsave(&sc->txbuflock, flags);
if (list_empty(&sc->txbuf)) {
int ret;
ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "resetting\n");
- /*
- * Convert to a hw channel description with the flags
- * constrained to reflect the current operating mode.
- */
- sc->curchan = hw->conf.chan;
ath5k_hw_set_intr(ah, 0);
ath5k_txq_cleanup(sc);
mutex_unlock(&sc->lock);
}
+/*
+ * TODO: Phy disable/diversity etc
+ */
static int
ath5k_config(struct ieee80211_hw *hw,
struct ieee80211_conf *conf)
struct ath5k_softc *sc = hw->priv;
sc->bintval = conf->beacon_int;
- ath5k_setcurmode(sc, conf->phymode);
+ sc->power_level = conf->power_level;
- return ath5k_chan_set(sc, conf->chan);
+ return ath5k_chan_set(sc, conf->channel);
}
static int
#if CHAN_DEBUG
#define ATH_CHAN_MAX (26+26+26+200+200)
#else
-#define ATH_CHAN_MAX (14+14+14+252+20) /* XXX what's the max? */
+#define ATH_CHAN_MAX (14+14+14+252+20)
#endif
/* Software Carrier, keeps track of the driver state
struct ieee80211_tx_queue_stats tx_stats;
struct ieee80211_low_level_stats ll_stats;
struct ieee80211_hw *hw; /* IEEE 802.11 common */
- struct ieee80211_hw_mode modes[NUM_DRIVER_MODES];
+ struct ieee80211_supported_band sbands[IEEE80211_NUM_BANDS];
struct ieee80211_channel channels[ATH_CHAN_MAX];
- struct ieee80211_rate rates[AR5K_MAX_RATES * NUM_DRIVER_MODES];
+ struct ieee80211_rate rates[AR5K_MAX_RATES * IEEE80211_NUM_BANDS];
enum ieee80211_if_types opmode;
struct ath5k_hw *ah; /* Atheros HW */
+ struct ieee80211_supported_band *curband;
+
+ u8 a_rates;
+ u8 b_rates;
+ u8 g_rates;
+ u8 xr_rates;
+
#if ATH5K_DEBUG
struct ath5k_dbg_info debug; /* debug info */
#endif
unsigned int nexttbtt; /* next beacon time in TU */
struct timer_list calib_tim; /* calibration timer */
+ int power_level; /* Requested tx power in dbm */
};
#define ath5k_hw_hasbssidmask(_ah) \
* HW information
*/
- /* Get reg domain from eeprom */
- ath5k_get_regdomain(ah);
-
ah->ah_op_mode = IEEE80211_IF_TYPE_STA;
ah->ah_radar.r_enabled = AR5K_TUNE_RADAR_ALERT;
ah->ah_turbo = false;
/* Get rate tables */
switch (mode) {
- case MODE_IEEE80211A:
+ case AR5K_MODE_11A:
return &ath5k_rt_11a;
- case MODE_ATHEROS_TURBO:
+ case AR5K_MODE_11A_TURBO:
return &ath5k_rt_turbo;
- case MODE_IEEE80211B:
+ case AR5K_MODE_11B:
return &ath5k_rt_11b;
- case MODE_IEEE80211G:
+ case AR5K_MODE_11G:
return &ath5k_rt_11g;
- case MODE_ATHEROS_TURBOG:
+ case AR5K_MODE_11G_TURBO:
return &ath5k_rt_xr;
}
ds_coef_exp, ds_coef_man, clock;
if (!(ah->ah_version == AR5K_AR5212) ||
- !(channel->val & CHANNEL_OFDM))
+ !(channel->hw_value & CHANNEL_OFDM))
BUG();
/* Seems there are two PLLs, one for baseband sampling and one
* for tuning. Tuning basebands are 40 MHz or 80MHz when in
* turbo. */
- clock = channel->val & CHANNEL_TURBO ? 80 : 40;
+ clock = channel->hw_value & CHANNEL_TURBO ? 80 : 40;
coef_scaled = ((5 * (clock << 24)) / 2) /
- channel->freq;
+ channel->center_freq;
for (coef_exp = 31; coef_exp > 0; coef_exp--)
if ((coef_scaled >> coef_exp) & 0x1)
* ath5k_hw_write_rate_duration - set rate duration during hw resets
*
* @ah: the &struct ath5k_hw
- * @driver_mode: one of enum ieee80211_phymode or our one of our own
- * vendor modes
+ * @mode: one of enum ath5k_driver_mode
*
* Write the rate duration table for the current mode upon hw reset. This
* is a helper for ath5k_hw_reset(). It seems all this is doing is setting
*
*/
static inline void ath5k_hw_write_rate_duration(struct ath5k_hw *ah,
- unsigned int driver_mode)
+ unsigned int mode)
{
struct ath5k_softc *sc = ah->ah_sc;
const struct ath5k_rate_table *rt;
+ struct ieee80211_rate srate = {};
unsigned int i;
/* Get rate table for the current operating mode */
- rt = ath5k_hw_get_rate_table(ah,
- driver_mode);
+ rt = ath5k_hw_get_rate_table(ah, mode);
/* Write rate duration table */
for (i = 0; i < rt->rate_count; i++) {
const struct ath5k_rate *rate, *control_rate;
+
u32 reg;
u16 tx_time;
/* Set ACK timeout */
reg = AR5K_RATE_DUR(rate->rate_code);
+ srate.bitrate = control_rate->rate_kbps/100;
+
/* An ACK frame consists of 10 bytes. If you add the FCS,
* which ieee80211_generic_frame_duration() adds,
* its 14 bytes. Note we use the control rate and not the
* ieee80211_duration() for a brief description of
* what rate we should choose to TX ACKs. */
tx_time = ieee80211_generic_frame_duration(sc->hw,
- sc->vif, 10, control_rate->rate_kbps/100);
+ sc->vif, 10, &srate);
ath5k_hw_reg_write(ah, tx_time, reg);
{
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
u32 data, s_seq, s_ant, s_led[3];
- unsigned int i, mode, freq, ee_mode, ant[2], driver_mode = -1;
+ unsigned int i, mode, freq, ee_mode, ant[2];
int ret;
ATH5K_TRACE(ah->ah_sc);
/*Wakeup the device*/
- ret = ath5k_hw_nic_wakeup(ah, channel->val, false);
+ ret = ath5k_hw_nic_wakeup(ah, channel->hw_value, false);
if (ret)
return ret;
return -EINVAL;
}
- switch (channel->val & CHANNEL_MODES) {
+ switch (channel->hw_value & CHANNEL_MODES) {
case CHANNEL_A:
- mode = AR5K_INI_VAL_11A;
+ mode = AR5K_MODE_11A;
freq = AR5K_INI_RFGAIN_5GHZ;
ee_mode = AR5K_EEPROM_MODE_11A;
- driver_mode = MODE_IEEE80211A;
break;
case CHANNEL_G:
- mode = AR5K_INI_VAL_11G;
+ mode = AR5K_MODE_11G;
freq = AR5K_INI_RFGAIN_2GHZ;
ee_mode = AR5K_EEPROM_MODE_11G;
- driver_mode = MODE_IEEE80211G;
break;
case CHANNEL_B:
- mode = AR5K_INI_VAL_11B;
+ mode = AR5K_MODE_11B;
freq = AR5K_INI_RFGAIN_2GHZ;
ee_mode = AR5K_EEPROM_MODE_11B;
- driver_mode = MODE_IEEE80211B;
break;
case CHANNEL_T:
- mode = AR5K_INI_VAL_11A_TURBO;
+ mode = AR5K_MODE_11A_TURBO;
freq = AR5K_INI_RFGAIN_5GHZ;
ee_mode = AR5K_EEPROM_MODE_11A;
- driver_mode = MODE_ATHEROS_TURBO;
break;
/*Is this ok on 5211 too ?*/
case CHANNEL_TG:
- mode = AR5K_INI_VAL_11G_TURBO;
+ mode = AR5K_MODE_11G_TURBO;
freq = AR5K_INI_RFGAIN_2GHZ;
ee_mode = AR5K_EEPROM_MODE_11G;
- driver_mode = MODE_ATHEROS_TURBOG;
break;
case CHANNEL_XR:
if (ah->ah_version == AR5K_AR5211) {
"XR mode not available on 5211");
return -EINVAL;
}
- mode = AR5K_INI_VAL_XR;
+ mode = AR5K_MODE_XR;
freq = AR5K_INI_RFGAIN_5GHZ;
ee_mode = AR5K_EEPROM_MODE_11A;
- driver_mode = MODE_IEEE80211A;
break;
default:
ATH5K_ERR(ah->ah_sc,
- "invalid channel: %d\n", channel->freq);
+ "invalid channel: %d\n", channel->center_freq);
return -EINVAL;
}
if (ah->ah_version > AR5K_AR5211){ /* found on 5213+ */
ath5k_hw_reg_write(ah, 0x0002a002, AR5K_PHY(11));
- if (channel->val == CHANNEL_G)
+ if (channel->hw_value == CHANNEL_G)
ath5k_hw_reg_write(ah, 0x00f80d80, AR5K_PHY(83)); /* 0x00fc0ec0 */
else
ath5k_hw_reg_write(ah, 0x00000000, AR5K_PHY(83));
AR5K_SREV_RAD_5112A) {
ath5k_hw_reg_write(ah, AR5K_PHY_CCKTXCTL_WORLD,
AR5K_PHY_CCKTXCTL);
- if (channel->val & CHANNEL_5GHZ)
+ if (channel->hw_value & CHANNEL_5GHZ)
data = 0xffb81020;
else
data = 0xffb80d20;
* mac80211 are integrated */
if (ah->ah_version == AR5K_AR5212 &&
ah->ah_sc->vif != NULL)
- ath5k_hw_write_rate_duration(ah, driver_mode);
+ ath5k_hw_write_rate_duration(ah, mode);
/*
* Write RF registers
/* Write OFDM timings on 5212*/
if (ah->ah_version == AR5K_AR5212 &&
- channel->val & CHANNEL_OFDM) {
+ channel->hw_value & CHANNEL_OFDM) {
ret = ath5k_hw_write_ofdm_timings(ah, channel);
if (ret)
return ret;
/*Enable/disable 802.11b mode on 5111
(enable 2111 frequency converter + CCK)*/
if (ah->ah_radio == AR5K_RF5111) {
- if (driver_mode == MODE_IEEE80211B)
+ if (mode == AR5K_MODE_11B)
AR5K_REG_ENABLE_BITS(ah, AR5K_TXCFG,
AR5K_TXCFG_B_MODE);
else
if (ah->ah_version != AR5K_AR5210) {
data = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
AR5K_PHY_RX_DELAY_M;
- data = (channel->val & CHANNEL_CCK) ?
+ data = (channel->hw_value & CHANNEL_CCK) ?
((data << 2) / 22) : (data / 10);
udelay(100 + data);
if (ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_CAL, 0, false)) {
ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n",
- channel->freq);
+ channel->center_freq);
return -EAGAIN;
}
- ret = ath5k_hw_noise_floor_calibration(ah, channel->freq);
+ ret = ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
if (ret)
return ret;
/* A and G modes can use QAM modulation which requires enabling
* I and Q calibration. Don't bother in B mode. */
- if (!(driver_mode == MODE_IEEE80211B)) {
+ if (!(mode == AR5K_MODE_11B)) {
ah->ah_calibration = true;
AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
/*
* Write to eeprom - currently disabled, use at your own risk
*/
+#if 0
static int ath5k_hw_eeprom_write(struct ath5k_hw *ah, u32 offset, u16 data)
{
-#if 0
+
u32 status, timeout;
ATH5K_TRACE(ah->ah_sc);
}
udelay(15);
}
-#endif
+
ATH5K_ERR(ah->ah_sc, "EEPROM Write is disabled!");
return -EIO;
}
+#endif
/*
* Translate binary channel representation in EEPROM to frequency
}
/*
- * Read/Write regulatory domain
- */
-static bool ath5k_eeprom_regulation_domain(struct ath5k_hw *ah, bool write,
- enum ath5k_regdom *regdomain)
-{
- u16 ee_regdomain;
-
- /* Read current value */
- if (write != true) {
- ee_regdomain = ah->ah_capabilities.cap_eeprom.ee_regdomain;
- *regdomain = ath5k_regdom_to_ieee(ee_regdomain);
- return true;
- }
-
- ee_regdomain = ath5k_regdom_from_ieee(*regdomain);
-
- /* Try to write a new value */
- if (ah->ah_capabilities.cap_eeprom.ee_protect &
- AR5K_EEPROM_PROTECT_WR_128_191)
- return false;
- if (ath5k_hw_eeprom_write(ah, AR5K_EEPROM_REG_DOMAIN, ee_regdomain)!=0)
- return false;
-
- ah->ah_capabilities.cap_eeprom.ee_regdomain = ee_regdomain;
-
- return true;
-}
-
-/*
- * Use the above to write a new regulatory domain
- */
-int ath5k_hw_set_regdomain(struct ath5k_hw *ah, u16 regdomain)
-{
- enum ath5k_regdom ieee_regdomain;
-
- ieee_regdomain = ath5k_regdom_to_ieee(regdomain);
-
- if (ath5k_eeprom_regulation_domain(ah, true, &ieee_regdomain) == true)
- return 0;
-
- return -EIO;
-}
-
-/*
* Fill the capabilities struct
*/
static int ath5k_hw_get_capabilities(struct ath5k_hw *ah)
ah->ah_capabilities.cap_range.range_2ghz_max = 0;
/* Set supported modes */
- __set_bit(MODE_IEEE80211A, ah->ah_capabilities.cap_mode);
- __set_bit(MODE_ATHEROS_TURBO, ah->ah_capabilities.cap_mode);
+ __set_bit(AR5K_MODE_11A, ah->ah_capabilities.cap_mode);
+ __set_bit(AR5K_MODE_11A_TURBO, ah->ah_capabilities.cap_mode);
} else {
/*
* XXX The tranceiver supports frequencies from 4920 to 6100GHz
ah->ah_capabilities.cap_range.range_5ghz_max = 6100;
/* Set supported modes */
- __set_bit(MODE_IEEE80211A,
+ __set_bit(AR5K_MODE_11A,
ah->ah_capabilities.cap_mode);
- __set_bit(MODE_ATHEROS_TURBO,
+ __set_bit(AR5K_MODE_11A_TURBO,
ah->ah_capabilities.cap_mode);
if (ah->ah_version == AR5K_AR5212)
- __set_bit(MODE_ATHEROS_TURBOG,
+ __set_bit(AR5K_MODE_11G_TURBO,
ah->ah_capabilities.cap_mode);
}
ah->ah_capabilities.cap_range.range_2ghz_max = 2732;
if (AR5K_EEPROM_HDR_11B(ee_header))
- __set_bit(MODE_IEEE80211B,
+ __set_bit(AR5K_MODE_11B,
ah->ah_capabilities.cap_mode);
if (AR5K_EEPROM_HDR_11G(ee_header))
- __set_bit(MODE_IEEE80211G,
+ __set_bit(AR5K_MODE_11G,
ah->ah_capabilities.cap_mode);
}
}
}
-/*********************************\
- Regulatory Domain/Channels Setup
-\*********************************/
-
-u16 ath5k_get_regdomain(struct ath5k_hw *ah)
-{
- u16 regdomain;
- enum ath5k_regdom ieee_regdomain;
-#ifdef COUNTRYCODE
- u16 code;
-#endif
-
- ath5k_eeprom_regulation_domain(ah, false, &ieee_regdomain);
- ah->ah_capabilities.cap_regdomain.reg_hw = ieee_regdomain;
-
-#ifdef COUNTRYCODE
- /*
- * Get the regulation domain by country code. This will ignore
- * the settings found in the EEPROM.
- */
- code = ieee80211_name2countrycode(COUNTRYCODE);
- ieee_regdomain = ieee80211_countrycode2regdomain(code);
-#endif
-
- regdomain = ath5k_regdom_from_ieee(ieee_regdomain);
- ah->ah_capabilities.cap_regdomain.reg_current = regdomain;
-
- return regdomain;
-}
/****************\
/* For AR5211 */
} else if (ah->ah_version == AR5K_AR5211) {
- if(mode > 2){ /* AR5K_INI_VAL_11B */
+ if(mode > 2){ /* AR5K_MODE_11B */
ATH5K_ERR(ah->ah_sc,"unsupported channel mode: %d\n", mode);
return -EINVAL;
}
int obdb = -1, bank = -1;
u32 ee_mode;
- AR5K_ASSERT_ENTRY(mode, AR5K_INI_VAL_MAX);
+ AR5K_ASSERT_ENTRY(mode, AR5K_MODE_MAX);
rf = ah->ah_rf_banks;
}
/* Modify bank 0 */
- if (channel->val & CHANNEL_2GHZ) {
- if (channel->val & CHANNEL_CCK)
+ if (channel->hw_value & CHANNEL_2GHZ) {
+ if (channel->hw_value & CHANNEL_CCK)
ee_mode = AR5K_EEPROM_MODE_11B;
else
ee_mode = AR5K_EEPROM_MODE_11G;
} else {
/* For 11a, Turbo and XR */
ee_mode = AR5K_EEPROM_MODE_11A;
- obdb = channel->freq >= 5725 ? 3 :
- (channel->freq >= 5500 ? 2 :
- (channel->freq >= 5260 ? 1 :
- (channel->freq > 4000 ? 0 : -1)));
+ obdb = channel->center_freq >= 5725 ? 3 :
+ (channel->center_freq >= 5500 ? 2 :
+ (channel->center_freq >= 5260 ? 1 :
+ (channel->center_freq > 4000 ? 0 : -1)));
if (!ath5k_hw_rfregs_op(rf, ah->ah_offset[6],
ee->ee_pwd_84, 1, 51, 3, true))
int obdb = -1, bank = -1;
u32 ee_mode;
- AR5K_ASSERT_ENTRY(mode, AR5K_INI_VAL_MAX);
+ AR5K_ASSERT_ENTRY(mode, AR5K_MODE_MAX);
rf = ah->ah_rf_banks;
if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_2112A
- && !test_bit(MODE_IEEE80211A, ah->ah_capabilities.cap_mode)){
+ && !test_bit(AR5K_MODE_11A, ah->ah_capabilities.cap_mode)){
rf_ini = rfregs_2112a;
rf_size = ARRAY_SIZE(rfregs_5112a);
if (mode < 2) {
}
/* Modify bank 6 */
- if (channel->val & CHANNEL_2GHZ) {
- if (channel->val & CHANNEL_OFDM)
+ if (channel->hw_value & CHANNEL_2GHZ) {
+ if (channel->hw_value & CHANNEL_OFDM)
ee_mode = AR5K_EEPROM_MODE_11G;
else
ee_mode = AR5K_EEPROM_MODE_11B;
} else {
/* For 11a, Turbo and XR */
ee_mode = AR5K_EEPROM_MODE_11A;
- obdb = channel->freq >= 5725 ? 3 :
- (channel->freq >= 5500 ? 2 :
- (channel->freq >= 5260 ? 1 :
- (channel->freq > 4000 ? 0 : -1)));
+ obdb = channel->center_freq >= 5725 ? 3 :
+ (channel->center_freq >= 5500 ? 2 :
+ (channel->center_freq >= 5260 ? 1 :
+ (channel->center_freq > 4000 ? 0 : -1)));
if (!ath5k_hw_rfregs_op(rf, ah->ah_offset[6],
ee->ee_ob[ee_mode][obdb], 3, 279, 0, true))
unsigned int rf_size, i;
int bank = -1;
- AR5K_ASSERT_ENTRY(mode, AR5K_INI_VAL_MAX);
+ AR5K_ASSERT_ENTRY(mode, AR5K_MODE_MAX);
rf = ah->ah_rf_banks;
* newer chipsets like the AR5212A who have a completely
* different RF/PHY part.
*/
- athchan = (ath5k_hw_bitswap((channel->chan - 24) / 2, 5) << 1) |
+ athchan = (ath5k_hw_bitswap((ieee80211_frequency_to_channel(channel->center_freq) - 24) / 2, 5) << 1) |
(1 << 6) | 0x1;
return athchan;
struct ieee80211_channel *channel)
{
struct ath5k_athchan_2ghz ath5k_channel_2ghz;
- unsigned int ath5k_channel = channel->chan;
+ unsigned int ath5k_channel = ieee80211_frequency_to_channel(channel->center_freq);
u32 data0, data1, clock;
int ret;
*/
data0 = data1 = 0;
- if (channel->val & CHANNEL_2GHZ) {
+ if (channel->hw_value & CHANNEL_2GHZ) {
/* Map 2GHz channel to 5GHz Atheros channel ID */
- ret = ath5k_hw_rf5111_chan2athchan(channel->chan,
+ ret = ath5k_hw_rf5111_chan2athchan(ieee80211_frequency_to_channel(channel->center_freq),
&ath5k_channel_2ghz);
if (ret)
return ret;
u16 c;
data = data0 = data1 = data2 = 0;
- c = channel->freq;
+ c = channel->center_freq;
/*
* Set the channel on the RF5112 or newer
* Check bounds supported by the PHY
* (don't care about regulation restrictions at this point)
*/
- if ((channel->freq < ah->ah_capabilities.cap_range.range_2ghz_min ||
- channel->freq > ah->ah_capabilities.cap_range.range_2ghz_max) &&
- (channel->freq < ah->ah_capabilities.cap_range.range_5ghz_min ||
- channel->freq > ah->ah_capabilities.cap_range.range_5ghz_max)) {
+ if ((channel->center_freq < ah->ah_capabilities.cap_range.range_2ghz_min ||
+ channel->center_freq > ah->ah_capabilities.cap_range.range_2ghz_max) &&
+ (channel->center_freq < ah->ah_capabilities.cap_range.range_5ghz_min ||
+ channel->center_freq > ah->ah_capabilities.cap_range.range_5ghz_max)) {
ATH5K_ERR(ah->ah_sc,
"channel out of supported range (%u MHz)\n",
- channel->freq);
+ channel->center_freq);
return -EINVAL;
}
if (ret)
return ret;
- ah->ah_current_channel.freq = channel->freq;
- ah->ah_current_channel.val = channel->val;
- ah->ah_turbo = channel->val == CHANNEL_T ? true : false;
+ ah->ah_current_channel.center_freq = channel->center_freq;
+ ah->ah_current_channel.hw_value = channel->hw_value;
+ ah->ah_turbo = channel->hw_value == CHANNEL_T ? true : false;
return 0;
}
if (ret) {
ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n",
- channel->freq);
+ channel->center_freq);
return ret;
}
- ret = ath5k_hw_noise_floor_calibration(ah, channel->freq);
+ ret = ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
if (ret)
return ret;
((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S));
done:
- ath5k_hw_noise_floor_calibration(ah, channel->freq);
+ ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
/* Request RF gain */
- if (channel->val & CHANNEL_5GHZ) {
+ if (channel->hw_value & CHANNEL_5GHZ) {
ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_max,
AR5K_PHY_PAPD_PROBE_TXPOWER) |
AR5K_PHY_PAPD_PROBE_TX_NEXT, AR5K_PHY_PAPD_PROBE);
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff