Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.
* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.
* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.
There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.
2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.
3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.
If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.
* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.
* Spin up waiting is to be removed and not converted to honor
deadline.
* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
return 0;
}
-static int ahci_softreset(struct ata_port *ap, unsigned int *class)
+static int ahci_softreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
struct ahci_port_priv *pp = ap->private_data;
void __iomem *port_mmio = ahci_port_base(ap);
*class = ATA_DEV_NONE;
if (ata_port_online(ap)) {
- if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
- rc = -EIO;
+ rc = ata_wait_ready(ap, deadline);
+ if (rc && rc != -ENODEV) {
reason = "device not ready";
goto fail;
}
return rc;
}
-static int ahci_hardreset(struct ata_port *ap, unsigned int *class)
+static int ahci_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
struct ahci_port_priv *pp = ap->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
tf.command = 0x80;
ata_tf_to_fis(&tf, d2h_fis, 0);
- rc = sata_std_hardreset(ap, class);
+ rc = sata_std_hardreset(ap, class, deadline);
ahci_start_engine(ap);
return rc;
}
-static int ahci_vt8251_hardreset(struct ata_port *ap, unsigned int *class)
+static int ahci_vt8251_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
int rc;
ahci_stop_engine(ap);
- rc = sata_port_hardreset(ap, sata_ehc_deb_timing(&ap->eh_context));
+ rc = sata_port_hardreset(ap, sata_ehc_deb_timing(&ap->eh_context),
+ deadline);
/* vt8251 needs SError cleared for the port to operate */
ahci_scr_write(ap, SCR_ERROR, ahci_scr_read(ap, SCR_ERROR));
/**
* piix_pata_prereset - prereset for PATA host controller
* @ap: Target port
+ * @deadline: deadline jiffies for the operation
*
* LOCKING:
* None (inherited from caller).
*/
-static int piix_pata_prereset(struct ata_port *ap)
+static int piix_pata_prereset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
static void piix_pata_error_handler(struct ata_port *ap)
ata_std_postreset);
}
-
static void piix_sata_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, NULL,
return 0;
}
-static void ata_bus_post_reset(struct ata_port *ap, unsigned int devmask)
+/**
+ * ata_wait_ready - sleep until BSY clears, or timeout
+ * @ap: port containing status register to be polled
+ * @deadline: deadline jiffies for the operation
+ *
+ * Sleep until ATA Status register bit BSY clears, or timeout
+ * occurs.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep).
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int ata_wait_ready(struct ata_port *ap, unsigned long deadline)
+{
+ unsigned long start = jiffies;
+ int warned = 0;
+
+ while (1) {
+ u8 status = ata_chk_status(ap);
+ unsigned long now = jiffies;
+
+ if (!(status & ATA_BUSY))
+ return 0;
+ if (status == 0xff)
+ return -ENODEV;
+ if (time_after(now, deadline))
+ return -EBUSY;
+
+ if (!warned && time_after(now, start + 5 * HZ) &&
+ (deadline - now > 3 * HZ)) {
+ ata_port_printk(ap, KERN_WARNING,
+ "port is slow to respond, please be patient "
+ "(Status 0x%x)\n", status);
+ warned = 1;
+ }
+
+ msleep(50);
+ }
+}
+
+static int ata_bus_post_reset(struct ata_port *ap, unsigned int devmask,
+ unsigned long deadline)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
unsigned int dev0 = devmask & (1 << 0);
unsigned int dev1 = devmask & (1 << 1);
- unsigned long timeout;
+ int rc;
/* if device 0 was found in ata_devchk, wait for its
* BSY bit to clear
*/
- if (dev0)
- ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+ if (dev0) {
+ rc = ata_wait_ready(ap, deadline);
+ if (rc && rc != -ENODEV)
+ return rc;
+ }
/* if device 1 was found in ata_devchk, wait for
* register access, then wait for BSY to clear
*/
- timeout = jiffies + ATA_TMOUT_BOOT;
while (dev1) {
u8 nsect, lbal;
lbal = ioread8(ioaddr->lbal_addr);
if ((nsect == 1) && (lbal == 1))
break;
- if (time_after(jiffies, timeout)) {
- dev1 = 0;
- break;
- }
+ if (time_after(jiffies, deadline))
+ return -EBUSY;
msleep(50); /* give drive a breather */
}
- if (dev1)
- ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+ if (dev1) {
+ rc = ata_wait_ready(ap, deadline);
+ if (rc && rc != -ENODEV)
+ return rc;
+ }
/* is all this really necessary? */
ap->ops->dev_select(ap, 0);
ap->ops->dev_select(ap, 1);
if (dev0)
ap->ops->dev_select(ap, 0);
+
+ return 0;
}
-static unsigned int ata_bus_softreset(struct ata_port *ap,
- unsigned int devmask)
+static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask,
+ unsigned long deadline)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
if (ata_check_status(ap) == 0xFF)
return 0;
- ata_bus_post_reset(ap, devmask);
-
- return 0;
+ return ata_bus_post_reset(ap, devmask, deadline);
}
/**
/* issue bus reset */
if (ap->flags & ATA_FLAG_SRST)
- if (ata_bus_softreset(ap, devmask))
+ if (ata_bus_softreset(ap, devmask, jiffies + 40 * HZ))
goto err_out;
/*
* sata_phy_debounce - debounce SATA phy status
* @ap: ATA port to debounce SATA phy status for
* @params: timing parameters { interval, duratinon, timeout } in msec
+ * @deadline: deadline jiffies for the operation
*
* Make sure SStatus of @ap reaches stable state, determined by
* holding the same value where DET is not 1 for @duration polled
* every @interval, before @timeout. Timeout constraints the
- * beginning of the stable state. Because, after hot unplugging,
- * DET gets stuck at 1 on some controllers, this functions waits
+ * beginning of the stable state. Because DET gets stuck at 1 on
+ * some controllers after hot unplugging, this functions waits
* until timeout then returns 0 if DET is stable at 1.
*
+ * @timeout is further limited by @deadline. The sooner of the
+ * two is used.
+ *
* LOCKING:
* Kernel thread context (may sleep)
*
* RETURNS:
* 0 on success, -errno on failure.
*/
-int sata_phy_debounce(struct ata_port *ap, const unsigned long *params)
+int sata_phy_debounce(struct ata_port *ap, const unsigned long *params,
+ unsigned long deadline)
{
unsigned long interval_msec = params[0];
- unsigned long duration = params[1] * HZ / 1000;
- unsigned long timeout = jiffies + params[2] * HZ / 1000;
- unsigned long last_jiffies;
+ unsigned long duration = msecs_to_jiffies(params[1]);
+ unsigned long last_jiffies, t;
u32 last, cur;
int rc;
+ t = jiffies + msecs_to_jiffies(params[2]);
+ if (time_before(t, deadline))
+ deadline = t;
+
if ((rc = sata_scr_read(ap, SCR_STATUS, &cur)))
return rc;
cur &= 0xf;
/* DET stable? */
if (cur == last) {
- if (cur == 1 && time_before(jiffies, timeout))
+ if (cur == 1 && time_before(jiffies, deadline))
continue;
if (time_after(jiffies, last_jiffies + duration))
return 0;
last = cur;
last_jiffies = jiffies;
- /* check timeout */
- if (time_after(jiffies, timeout))
+ /* check deadline */
+ if (time_after(jiffies, deadline))
return -EBUSY;
}
}
* sata_phy_resume - resume SATA phy
* @ap: ATA port to resume SATA phy for
* @params: timing parameters { interval, duratinon, timeout } in msec
+ * @deadline: deadline jiffies for the operation
*
* Resume SATA phy of @ap and debounce it.
*
* RETURNS:
* 0 on success, -errno on failure.
*/
-int sata_phy_resume(struct ata_port *ap, const unsigned long *params)
+int sata_phy_resume(struct ata_port *ap, const unsigned long *params,
+ unsigned long deadline)
{
u32 scontrol;
int rc;
*/
msleep(200);
- return sata_phy_debounce(ap, params);
+ return sata_phy_debounce(ap, params, deadline);
}
-static void ata_wait_spinup(struct ata_port *ap)
+static void ata_wait_spinup(struct ata_port *ap, unsigned long deadline)
{
struct ata_eh_context *ehc = &ap->eh_context;
unsigned long end, secs;
/* first, debounce phy if SATA */
if (ap->cbl == ATA_CBL_SATA) {
- rc = sata_phy_debounce(ap, sata_deb_timing_hotplug);
+ rc = sata_phy_debounce(ap, sata_deb_timing_hotplug, deadline);
/* if debounced successfully and offline, no need to wait */
if ((rc == 0 || rc == -EOPNOTSUPP) && ata_port_offline(ap))
/**
* ata_std_prereset - prepare for reset
* @ap: ATA port to be reset
+ * @deadline: deadline jiffies for the operation
*
* @ap is about to be reset. Initialize it.
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
-int ata_std_prereset(struct ata_port *ap)
+int ata_std_prereset(struct ata_port *ap, unsigned long deadline)
{
struct ata_eh_context *ehc = &ap->eh_context;
const unsigned long *timing = sata_ehc_deb_timing(ehc);
if ((ehc->i.flags & ATA_EHI_HOTPLUGGED) &&
(ap->flags & ATA_FLAG_SKIP_D2H_BSY))
- ata_wait_spinup(ap);
+ ata_wait_spinup(ap, deadline);
/* if we're about to do hardreset, nothing more to do */
if (ehc->i.action & ATA_EH_HARDRESET)
/* if SATA, resume phy */
if (ap->cbl == ATA_CBL_SATA) {
- rc = sata_phy_resume(ap, timing);
+ rc = sata_phy_resume(ap, timing, deadline);
if (rc && rc != -EOPNOTSUPP) {
/* phy resume failed */
ata_port_printk(ap, KERN_WARNING, "failed to resume "
* Reg FIS and we don't know that no device is attached.
*/
if (!(ap->flags & ATA_FLAG_SKIP_D2H_BSY) && !ata_port_offline(ap))
- ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+ ata_wait_ready(ap, deadline);
return 0;
}
* ata_std_softreset - reset host port via ATA SRST
* @ap: port to reset
* @classes: resulting classes of attached devices
+ * @deadline: deadline jiffies for the operation
*
* Reset host port using ATA SRST.
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
-int ata_std_softreset(struct ata_port *ap, unsigned int *classes)
+int ata_std_softreset(struct ata_port *ap, unsigned int *classes,
+ unsigned long deadline)
{
unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
- unsigned int devmask = 0, err_mask;
+ unsigned int devmask = 0;
+ int rc;
u8 err;
DPRINTK("ENTER\n");
/* issue bus reset */
DPRINTK("about to softreset, devmask=%x\n", devmask);
- err_mask = ata_bus_softreset(ap, devmask);
- if (err_mask) {
- ata_port_printk(ap, KERN_ERR, "SRST failed (err_mask=0x%x)\n",
- err_mask);
- return -EIO;
+ rc = ata_bus_softreset(ap, devmask, deadline);
+ if (rc) {
+ ata_port_printk(ap, KERN_ERR, "SRST failed (errno=%d)\n", rc);
+ return rc;
}
/* determine by signature whether we have ATA or ATAPI devices */
* sata_port_hardreset - reset port via SATA phy reset
* @ap: port to reset
* @timing: timing parameters { interval, duratinon, timeout } in msec
+ * @deadline: deadline jiffies for the operation
*
* SATA phy-reset host port using DET bits of SControl register.
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
-int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing)
+int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing,
+ unsigned long deadline)
{
u32 scontrol;
int rc;
msleep(1);
/* bring phy back */
- rc = sata_phy_resume(ap, timing);
+ rc = sata_phy_resume(ap, timing, deadline);
out:
DPRINTK("EXIT, rc=%d\n", rc);
return rc;
* sata_std_hardreset - reset host port via SATA phy reset
* @ap: port to reset
* @class: resulting class of attached device
+ * @deadline: deadline jiffies for the operation
*
* SATA phy-reset host port using DET bits of SControl register,
* wait for !BSY and classify the attached device.
* RETURNS:
* 0 on success, -errno otherwise.
*/
-int sata_std_hardreset(struct ata_port *ap, unsigned int *class)
+int sata_std_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
const unsigned long *timing = sata_ehc_deb_timing(&ap->eh_context);
int rc;
DPRINTK("ENTER\n");
/* do hardreset */
- rc = sata_port_hardreset(ap, timing);
+ rc = sata_port_hardreset(ap, timing, deadline);
if (rc) {
ata_port_printk(ap, KERN_ERR,
"COMRESET failed (errno=%d)\n", rc);
/* wait a while before checking status, see SRST for more info */
msleep(150);
- if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
+ rc = ata_wait_ready(ap, deadline);
+ if (rc && rc != -ENODEV) {
ata_port_printk(ap, KERN_ERR,
- "COMRESET failed (device not ready)\n");
- return -EIO;
+ "COMRESET failed (errno=%d)\n", rc);
+ return rc;
}
ap->ops->dev_select(ap, 0); /* probably unnecessary */
EXPORT_SYMBOL_GPL(ata_ratelimit);
EXPORT_SYMBOL_GPL(ata_wait_register);
EXPORT_SYMBOL_GPL(ata_busy_sleep);
+EXPORT_SYMBOL_GPL(ata_wait_ready);
EXPORT_SYMBOL_GPL(ata_port_queue_task);
EXPORT_SYMBOL_GPL(ata_scsi_ioctl);
EXPORT_SYMBOL_GPL(ata_scsi_queuecmd);
}
static int ata_do_reset(struct ata_port *ap, ata_reset_fn_t reset,
- unsigned int *classes)
+ unsigned int *classes, unsigned long deadline)
{
int i, rc;
for (i = 0; i < ATA_MAX_DEVICES; i++)
classes[i] = ATA_DEV_UNKNOWN;
- rc = reset(ap, classes);
+ rc = reset(ap, classes, deadline);
if (rc)
return rc;
ehc->i.action |= ATA_EH_HARDRESET;
if (prereset) {
- rc = prereset(ap);
+ rc = prereset(ap, jiffies + 40 * HZ);
if (rc) {
if (rc == -ENOENT) {
ata_port_printk(ap, KERN_DEBUG,
else
ehc->i.flags |= ATA_EHI_DID_SOFTRESET;
- rc = ata_do_reset(ap, reset, classes);
+ rc = ata_do_reset(ap, reset, classes, jiffies + 40 * HZ);
did_followup_srst = 0;
if (reset == hardreset &&
}
ata_eh_about_to_do(ap, NULL, ATA_EH_RESET_MASK);
- rc = ata_do_reset(ap, reset, classes);
+ rc = ata_do_reset(ap, reset, classes, jiffies + 40 * HZ);
if (rc == 0 && classify &&
classes[0] == ATA_DEV_UNKNOWN) {
/**
* amd_probe_init - perform reset handling
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Reset sequence checking enable bits to see which ports are
* active.
*/
-static int amd_pre_reset(struct ata_port *ap)
+static int amd_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits amd_enable_bits[] = {
{ 0x40, 1, 0x02, 0x02 },
if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
-
+ return ata_std_prereset(ap, deadline);
}
static void amd_error_handler(struct ata_port *ap)
* space for us.
*/
-static int nv_pre_reset(struct ata_port *ap) {
+static int nv_pre_reset(struct ata_port *ap, unsigned long deadline)
+{
static const struct pci_bits nv_enable_bits[] = {
{ 0x50, 1, 0x02, 0x02 },
{ 0x50, 1, 0x01, 0x01 }
if (!pci_test_config_bits(pdev, &nv_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
static void nv_error_handler(struct ata_port *ap)
static int clock = 0;
-static int artop6210_pre_reset(struct ata_port *ap)
+static int artop6210_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
const struct pci_bits artop_enable_bits[] = {
if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* artop6260_pre_reset - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* The ARTOP hardware reports the cable detect bits in register 0x49.
* Nothing complicated needed here.
*/
-static int artop6260_pre_reset(struct ata_port *ap)
+static int artop6260_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits artop_enable_bits[] = {
{ 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */
ATIIXP_IDE_UDMA_MODE = 0x56
};
-static int atiixp_pre_reset(struct ata_port *ap)
+static int atiixp_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits atiixp_enable_bits[] = {
{ 0x48, 1, 0x01, 0x00 },
if (!pci_test_config_bits(pdev, &atiixp_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
static void atiixp_error_handler(struct ata_port *ap)
/**
* cs5535_cable_detect - detect cable type
* @ap: Port to detect on
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection for ATA66 capable cable. Return a libata
* cable type.
/**
* efar_pre_reset - Enable bits
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection for the EFAR ATA interface. This is
* different to the PIIX arrangement
*/
-static int efar_pre_reset(struct ata_port *ap)
+static int efar_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits efar_enable_bits[] = {
{ 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
if (!pci_test_config_bits(pdev, &efar_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
return ATA_CBL_PATA80;
}
-static int hpt36x_pre_reset(struct ata_port *ap)
+static int hpt36x_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits hpt36x_enable_bits[] = {
{ 0x50, 1, 0x04, 0x04 },
if (!pci_test_config_bits(pdev, &hpt36x_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* hpt37x_pre_reset - reset the hpt37x bus
* @ap: ATA port to reset
+ * @deadline: deadline jiffies for the operation
*
* Perform the initial reset handling for the 370/372 and 374 func 0
*/
-static int hpt37x_pre_reset(struct ata_port *ap)
+static int hpt37x_pre_reset(struct ata_port *ap, unsigned long deadline)
{
u8 scr2, ata66;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(100);
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
-static int hpt374_pre_reset(struct ata_port *ap)
+static int hpt374_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits hpt37x_enable_bits[] = {
{ 0x50, 1, 0x04, 0x04 },
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(100);
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
* Reset the hardware and state machine,
*/
-static int hpt3xn_pre_reset(struct ata_port *ap)
+static int hpt3xn_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
/* Reset the state machine */
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(100);
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* it8213_pre_reset - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Filter out ports by the enable bits before doing the normal reset
* and probe.
*/
-static int it8213_pre_reset(struct ata_port *ap)
+static int it8213_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits it8213_enable_bits[] = {
{ 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* jmicron_pre_reset - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform the PATA port setup we need.
-
+ *
* On the Jmicron 361/363 there is a single PATA port that can be mapped
* either as primary or secondary (or neither). We don't do any policy
* and setup here. We assume that has been done by init_one and the
* BIOS.
*/
-static int jmicron_pre_reset(struct ata_port *ap)
+static int jmicron_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 control;
ap->cbl = ATA_CBL_SATA;
break;
}
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* marvell_pre_reset - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform the PATA port setup we need.
*/
-static int marvell_pre_reset(struct ata_port *ap)
+static int marvell_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 devices;
case 1: /* Legacy SATA port */
return ATA_CBL_SATA;
}
+
BUG();
return 0; /* Our BUG macro needs the right markup */
}
SECONDARY = (1 << 14)
};
-static int mpiix_pre_reset(struct ata_port *ap)
+static int mpiix_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 };
if (!pci_test_config_bits(pdev, &mpiix_enable_bits))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* ns87410_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Check enabled ports
*/
-static int ns87410_pre_reset(struct ata_port *ap)
+static int ns87410_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits ns87410_enable_bits[] = {
if (!pci_test_config_bits(pdev, &ns87410_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* oldpiix_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int oldpiix_pre_reset(struct ata_port *ap)
+static int oldpiix_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits oldpiix_enable_bits[] = {
if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* opti_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int opti_pre_reset(struct ata_port *ap)
+static int opti_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits opti_enable_bits[] = {
if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* optidma_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int optidma_pre_reset(struct ata_port *ap)
+static int optidma_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits optidma_enable_bits = {
if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* pdc2027x_prereset - prereset for PATA host controller
* @ap: Target port
+ * @deadline: deadline jiffies for the operation
*
* Probeinit including cable detection.
*
* None (inherited from caller).
*/
-static int pdc2027x_prereset(struct ata_port *ap)
+static int pdc2027x_prereset(struct ata_port *ap, unsigned long deadline)
{
/* Check whether port enabled */
if (!pdc2027x_port_enabled(ap))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* serverworks_cable_detect - cable detection
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection according to the device and subvendor
* identifications
*/
-static int serverworks_cable_detect(struct ata_port *ap) {
+static int serverworks_cable_detect(struct ata_port *ap)
+{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct sv_cable_table *cb = cable_detect;
/**
* sil680_bus_reset - reset the SIL680 bus
* @ap: ATA port to reset
+ * @deadline: deadline jiffies for the operation
*
* Perform the SIL680 housekeeping when doing an ATA bus reset
*/
-static int sil680_bus_reset(struct ata_port *ap,unsigned int *classes)
+static int sil680_bus_reset(struct ata_port *ap,unsigned int *classes,
+ unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned long addr = sil680_selreg(ap, 0);
pci_write_config_byte(pdev, addr, reset | 0x03);
udelay(25);
pci_write_config_byte(pdev, addr, reset);
- return ata_std_softreset(ap, classes);
+ return ata_std_softreset(ap, classes, deadline);
}
static void sil680_error_handler(struct ata_port *ap)
/**
* sis_133_cable_detect - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection for the later UDMA133 capable
* SiS chipset.
/**
* sis_66_cable_detect - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection on the UDMA66, UDMA100 and early UDMA133
* SiS IDE controllers.
/**
* sis_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int sis_pre_reset(struct ata_port *ap)
+static int sis_old_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits sis_enable_bits[] = {
{ 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
/**
* sl82c105_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int sl82c105_pre_reset(struct ata_port *ap)
+static int sl82c105_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits sl82c105_enable_bits[] = {
{ 0x40, 1, 0x01, 0x01 },
if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
* triflex_prereset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int triflex_prereset(struct ata_port *ap)
+static int triflex_prereset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits triflex_enable_bits[] = {
{ 0x80, 1, 0x01, 0x01 },
if (!pci_test_config_bits(pdev, &triflex_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
return ATA_CBL_PATA40;
}
-static int via_pre_reset(struct ata_port *ap)
+static int via_pre_reset(struct ata_port *ap, unsigned long deadline)
{
const struct via_isa_bridge *config = ap->host->private_data;
if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no]))
return -ENOENT;
}
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
* SRST and SControl hardreset don't give valid signature on this
* controller. Only controller specific hardreset mechanism works.
*/
-static int inic_hardreset(struct ata_port *ap, unsigned int *class)
+static int inic_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
void __iomem *port_base = inic_port_base(ap);
void __iomem *idma_ctl = port_base + PORT_IDMA_CTL;
msleep(1);
writew(val & ~IDMA_CTL_RST_ATA, idma_ctl);
- rc = sata_phy_resume(ap, timing);
+ rc = sata_phy_resume(ap, timing, deadline);
if (rc) {
ata_port_printk(ap, KERN_WARNING, "failed to resume "
"link after reset (errno=%d)\n", rc);
/* wait a while before checking status */
msleep(150);
- if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
- ata_port_printk(ap, KERN_WARNING,
- "device busy after hardreset\n");
- return -EIO;
+ rc = ata_wait_ready(ap, deadline);
+ if (rc && rc != -ENODEV) {
+ ata_port_printk(ap, KERN_WARNING, "device not ready "
+ "after hardreset (errno=%d)\n", rc);
+ return rc;
}
ata_tf_read(ap, &tf);
writeb(mask, mmio_base + NV_INT_ENABLE_CK804);
}
-static int nv_hardreset(struct ata_port *ap, unsigned int *class)
+static int nv_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
unsigned int dummy;
* some controllers. Don't classify on hardreset. For more
* info, see http://bugme.osdl.org/show_bug.cgi?id=3352
*/
- return sata_std_hardreset(ap, &dummy);
+ return sata_std_hardreset(ap, &dummy, deadline);
}
static void nv_error_handler(struct ata_port *ap)
return 0;
}
-static int sil24_softreset(struct ata_port *ap, unsigned int *class)
+static int sil24_softreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
void __iomem *port = ap->ioaddr.cmd_addr;
struct sil24_port_priv *pp = ap->private_data;
mask = (PORT_IRQ_COMPLETE | PORT_IRQ_ERROR) << PORT_IRQ_RAW_SHIFT;
irq_stat = ata_wait_register(port + PORT_IRQ_STAT, mask, 0x0,
- 100, ATA_TMOUT_BOOT / HZ * 1000);
+ 100, jiffies_to_msecs(deadline - jiffies));
writel(irq_stat, port + PORT_IRQ_STAT); /* clear IRQs */
irq_stat >>= PORT_IRQ_RAW_SHIFT;
return -EIO;
}
-static int sil24_hardreset(struct ata_port *ap, unsigned int *class)
+static int sil24_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
void __iomem *port = ap->ioaddr.cmd_addr;
const char *reason;
/* SStatus oscillates between zero and valid status after
* DEV_RST, debounce it.
*/
- rc = sata_phy_debounce(ap, sata_deb_timing_long);
+ rc = sata_phy_debounce(ap, sata_deb_timing_long, deadline);
if (rc) {
reason = "PHY debouncing failed";
goto err;
/**
* vt6420_prereset - prereset for vt6420
* @ap: target ATA port
+ * @deadline: deadline jiffies for the operation
*
* SCR registers on vt6420 are pieces of shit and may hang the
* whole machine completely if accessed with the wrong timing.
* RETURNS:
* 0 on success, -errno otherwise.
*/
-static int vt6420_prereset(struct ata_port *ap)
+static int vt6420_prereset(struct ata_port *ap, unsigned long deadline)
{
struct ata_eh_context *ehc = &ap->eh_context;
unsigned long timeout = jiffies + (HZ * 5);
skip_scr:
/* wait for !BSY */
- ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+ ata_wait_ready(ap, deadline);
return 0;
}
/* typedefs */
typedef void (*ata_qc_cb_t) (struct ata_queued_cmd *qc);
-typedef int (*ata_prereset_fn_t)(struct ata_port *ap);
-typedef int (*ata_reset_fn_t)(struct ata_port *ap, unsigned int *classes);
+typedef int (*ata_prereset_fn_t)(struct ata_port *ap, unsigned long deadline);
+typedef int (*ata_reset_fn_t)(struct ata_port *ap, unsigned int *classes,
+ unsigned long deadline);
typedef void (*ata_postreset_fn_t)(struct ata_port *ap, unsigned int *classes);
struct ata_ioports {
extern void sata_phy_reset(struct ata_port *ap);
extern void ata_bus_reset(struct ata_port *ap);
extern int sata_set_spd(struct ata_port *ap);
-extern int sata_phy_debounce(struct ata_port *ap, const unsigned long *param);
-extern int sata_phy_resume(struct ata_port *ap, const unsigned long *param);
-extern int ata_std_prereset(struct ata_port *ap);
-extern int ata_std_softreset(struct ata_port *ap, unsigned int *classes);
-extern int sata_port_hardreset(struct ata_port *ap,
- const unsigned long *timing);
-extern int sata_std_hardreset(struct ata_port *ap, unsigned int *class);
+extern int sata_phy_debounce(struct ata_port *ap, const unsigned long *param,
+ unsigned long deadline);
+extern int sata_phy_resume(struct ata_port *ap, const unsigned long *param,
+ unsigned long deadline);
+extern int ata_std_prereset(struct ata_port *ap, unsigned long deadline);
+extern int ata_std_softreset(struct ata_port *ap, unsigned int *classes,
+ unsigned long deadline);
+extern int sata_port_hardreset(struct ata_port *ap, const unsigned long *timing,
+ unsigned long deadline);
+extern int sata_std_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline);
extern void ata_std_postreset(struct ata_port *ap, unsigned int *classes);
extern void ata_port_disable(struct ata_port *);
extern void ata_std_ports(struct ata_ioports *ioaddr);
extern int ata_ratelimit(void);
extern int ata_busy_sleep(struct ata_port *ap,
unsigned long timeout_pat, unsigned long timeout);
+extern int ata_wait_ready(struct ata_port *ap, unsigned long deadline);
extern void ata_port_queue_task(struct ata_port *ap, work_func_t fn,
void *data, unsigned long delay);
extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff