memstick: optimize setup of JMicron host parameters

Set correct clock management values to improve over-all performance.

Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

diff --git a/drivers/memstick/host/jmb38x_ms.c b/drivers/memstick/host/jmb38x_ms.c
index f91037d..8770a5f 100644 (file)
--- a/drivers/memstick/host/jmb38x_ms.c
+++ b/drivers/memstick/host/jmb38x_ms.c
@@ -131,6 +131,12 @@ struct jmb38x_ms {
 #define PAD_PU_PD_ON_MS_SOCK0 0x5f8f0000
 #define PAD_PU_PD_ON_MS_SOCK1 0x0f0f0000
 
+#define CLOCK_CONTROL_40MHZ   0x00000001
+#define CLOCK_CONTROL_50MHZ   0x00000002
+#define CLOCK_CONTROL_60MHZ   0x00000008
+#define CLOCK_CONTROL_62_5MHZ 0x0000000c
+#define CLOCK_CONTROL_OFF     0x00000000
+
 enum {
        CMD_READY    = 0x01,
        FIFO_READY   = 0x02,
@@ -607,19 +613,18 @@ static void jmb38x_ms_reset(struct jmb38x_ms_host *host)
 {
        unsigned int host_ctl = readl(host->addr + HOST_CONTROL);
 
-       writel(host_ctl | HOST_CONTROL_RESET_REQ | HOST_CONTROL_RESET,
-              host->addr + HOST_CONTROL);
+       writel(HOST_CONTROL_RESET_REQ, host->addr + HOST_CONTROL);
 
        while (HOST_CONTROL_RESET_REQ
               & (host_ctl = readl(host->addr + HOST_CONTROL))) {
-               ndelay(100);
-               dev_dbg(&host->chip->pdev->dev, "reset\n");
+               ndelay(20);
+               dev_dbg(&host->chip->pdev->dev, "reset %08x\n", host_ctl);
        }
 
-       writel(INT_STATUS_ALL, host->addr + INT_STATUS_ENABLE);
+       writel(HOST_CONTROL_RESET, host->addr + HOST_CONTROL);
+       mmiowb();
        writel(INT_STATUS_ALL, host->addr + INT_SIGNAL_ENABLE);
-
-       dev_dbg(&host->chip->pdev->dev, "reset\n");
+       writel(INT_STATUS_ALL, host->addr + INT_STATUS_ENABLE);
 }
 
 static void jmb38x_ms_set_param(struct memstick_host *msh,
@@ -627,10 +632,8 @@ static void jmb38x_ms_set_param(struct memstick_host *msh,
                                int value)
 {
        struct jmb38x_ms_host *host = memstick_priv(msh);
-       unsigned int host_ctl;
-       unsigned long flags;
-
-       spin_lock_irqsave(&host->lock, flags);
+       unsigned int host_ctl = readl(host->addr + HOST_CONTROL);
+       unsigned int clock_ctl = CLOCK_CONTROL_40MHZ, clock_delay = 0;
 
        switch (param) {
        case MEMSTICK_POWER:
@@ -638,60 +641,57 @@ static void jmb38x_ms_set_param(struct memstick_host *msh,
                        jmb38x_ms_reset(host);
 
                        writel(host->id ? PAD_PU_PD_ON_MS_SOCK1
-                                         : PAD_PU_PD_ON_MS_SOCK0,
+                                       : PAD_PU_PD_ON_MS_SOCK0,
                               host->addr + PAD_PU_PD);
 
                        writel(PAD_OUTPUT_ENABLE_MS,
                               host->addr + PAD_OUTPUT_ENABLE);
 
-                       host_ctl = readl(host->addr + HOST_CONTROL);
-                       host_ctl |= 7;
-                       writel(host_ctl | (HOST_CONTROL_POWER_EN
-                                          | HOST_CONTROL_CLOCK_EN),
-                              host->addr + HOST_CONTROL);
+                       host_ctl = 7;
+                       host_ctl |= HOST_CONTROL_POWER_EN
+                                | HOST_CONTROL_CLOCK_EN;
+                       writel(host_ctl, host->addr + HOST_CONTROL);
 
                        dev_dbg(&host->chip->pdev->dev, "power on\n");
                } else if (value == MEMSTICK_POWER_OFF) {
-                       writel(readl(host->addr + HOST_CONTROL)
-                              & ~(HOST_CONTROL_POWER_EN
-                                  | HOST_CONTROL_CLOCK_EN),
-                              host->addr +  HOST_CONTROL);
+                       host_ctl &= ~(HOST_CONTROL_POWER_EN
+                                     | HOST_CONTROL_CLOCK_EN);
+                       writel(host_ctl, host->addr +  HOST_CONTROL);
                        writel(0, host->addr + PAD_OUTPUT_ENABLE);
                        writel(PAD_PU_PD_OFF, host->addr + PAD_PU_PD);
                        dev_dbg(&host->chip->pdev->dev, "power off\n");
                }
                break;
        case MEMSTICK_INTERFACE:
-               /* jmb38x_ms_reset(host); */
-
-               host_ctl = readl(host->addr + HOST_CONTROL);
                host_ctl &= ~(3 << HOST_CONTROL_IF_SHIFT);
-               /* host_ctl |= 7; */
 
                if (value == MEMSTICK_SERIAL) {
                        host_ctl &= ~HOST_CONTROL_FAST_CLK;
                        host_ctl |= HOST_CONTROL_IF_SERIAL
                                    << HOST_CONTROL_IF_SHIFT;
                        host_ctl |= HOST_CONTROL_REI;
-                       writel(0, host->addr + CLOCK_DELAY);
+                       clock_ctl = CLOCK_CONTROL_40MHZ;
+                       clock_delay = 0;
                } else if (value == MEMSTICK_PAR4) {
                        host_ctl |= HOST_CONTROL_FAST_CLK;
                        host_ctl |= HOST_CONTROL_IF_PAR4
                                    << HOST_CONTROL_IF_SHIFT;
                        host_ctl &= ~HOST_CONTROL_REI;
-                       writel(4, host->addr + CLOCK_DELAY);
+                       clock_ctl = CLOCK_CONTROL_40MHZ;
+                       clock_delay = 4;
                } else if (value == MEMSTICK_PAR8) {
                        host_ctl |= HOST_CONTROL_FAST_CLK;
                        host_ctl |= HOST_CONTROL_IF_PAR8
                                    << HOST_CONTROL_IF_SHIFT;
                        host_ctl &= ~HOST_CONTROL_REI;
-                       writel(4, host->addr + CLOCK_DELAY);
+                       clock_ctl = CLOCK_CONTROL_60MHZ;
+                       clock_delay = 0;
                }
                writel(host_ctl, host->addr + HOST_CONTROL);
+               writel(clock_ctl, host->addr + CLOCK_CONTROL);
+               writel(clock_delay, host->addr + CLOCK_DELAY);
                break;
        };
-
-       spin_unlock_irqrestore(&host->lock, flags);
 }
 
 #ifdef CONFIG_PM