bool "Enable support for IQ80321"
help
Say Y here if you want to run your kernel on the Intel IQ80321
- evaluation kit for the IOP321 chipset.
+ evaluation kit for the IOP321 processor.
config ARCH_IQ31244
- bool "Enable support for IQ31244"
+ bool "Enable support for EP80219/IQ31244"
help
- Say Y here if you want to run your kernel on the Intel IQ31244
- evaluation kit for the IOP321 chipset.
+ Say Y here if you want to run your kernel on the Intel EP80219
+ evaluation kit for the Intel 80219 processor (a IOP321 variant)
+ or the IQ31244 evaluation kit for the IOP321 processor.
endmenu
if (slot == 0) {
/* CFlash */
- irq = IRQ_IOP321_XINT1;
+ irq = IRQ_IOP32X_XINT1;
} else if (slot == 1) {
/* 82551 Pro 100 */
- irq = IRQ_IOP321_XINT0;
+ irq = IRQ_IOP32X_XINT0;
} else if (slot == 2) {
/* PCI-X Slot */
- irq = IRQ_IOP321_XINT3;
+ irq = IRQ_IOP32X_XINT3;
} else if (slot == 3) {
/* SATA */
- irq = IRQ_IOP321_XINT2;
+ irq = IRQ_IOP32X_XINT2;
} else {
printk(KERN_ERR "ep80219_pci_map_irq() called for unknown "
"device PCI:%d:%d:%d\n", dev->bus->number,
if (slot == 0) {
/* CFlash */
- irq = IRQ_IOP321_XINT1;
+ irq = IRQ_IOP32X_XINT1;
} else if (slot == 1) {
/* SATA */
- irq = IRQ_IOP321_XINT2;
+ irq = IRQ_IOP32X_XINT2;
} else if (slot == 2) {
/* PCI-X Slot */
- irq = IRQ_IOP321_XINT3;
+ irq = IRQ_IOP32X_XINT3;
} else if (slot == 3) {
/* 82546 GigE */
- irq = IRQ_IOP321_XINT0;
+ irq = IRQ_IOP32X_XINT0;
} else {
- printk(KERN_ERR "iq31244_pci_map_irq() called for unknown "
+ printk(KERN_ERR "iq31244_pci_map_irq called for unknown "
"device PCI:%d:%d:%d\n", dev->bus->number,
PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
irq = -1;
{
.mapbase = IQ31244_UART,
.membase = (char *)IQ31244_UART,
- .irq = IRQ_IOP321_XINT1,
+ .irq = IRQ_IOP32X_XINT1,
.flags = UPF_SKIP_TEST,
.iotype = UPIO_MEM,
.regshift = 0,
.io_pg_offst = ((IQ31244_UART) >> 18) & 0xfffc,
.boot_params = 0xa0000100,
.map_io = iq31244_map_io,
- .init_irq = iop321_init_irq,
+ .init_irq = iop32x_init_irq,
.timer = &iq31244_timer,
.init_machine = iq31244_init_machine,
MACHINE_END
if ((slot == 2 || slot == 6) && pin == 1) {
/* PCI-X Slot INTA */
- irq = IRQ_IOP321_XINT2;
+ irq = IRQ_IOP32X_XINT2;
} else if ((slot == 2 || slot == 6) && pin == 2) {
/* PCI-X Slot INTA */
- irq = IRQ_IOP321_XINT3;
+ irq = IRQ_IOP32X_XINT3;
} else if ((slot == 2 || slot == 6) && pin == 3) {
/* PCI-X Slot INTA */
- irq = IRQ_IOP321_XINT0;
+ irq = IRQ_IOP32X_XINT0;
} else if ((slot == 2 || slot == 6) && pin == 4) {
/* PCI-X Slot INTA */
- irq = IRQ_IOP321_XINT1;
+ irq = IRQ_IOP32X_XINT1;
} else if (slot == 4 || slot == 8) {
/* Gig-E */
- irq = IRQ_IOP321_XINT0;
+ irq = IRQ_IOP32X_XINT0;
} else {
printk(KERN_ERR "iq80321_pci_map_irq() called for unknown "
"device PCI:%d:%d:%d\n", dev->bus->number,
{
.mapbase = IQ80321_UART,
.membase = (char *)IQ80321_UART,
- .irq = IRQ_IOP321_XINT1,
+ .irq = IRQ_IOP32X_XINT1,
.flags = UPF_SKIP_TEST,
.iotype = UPIO_MEM,
.regshift = 0,
.io_pg_offst = ((IQ80321_UART) >> 18) & 0xfffc,
.boot_params = 0xa0000100,
.map_io = iq80321_map_io,
- .init_irq = iop321_init_irq,
+ .init_irq = iop32x_init_irq,
.timer = &iq80321_timer,
.init_machine = iq80321_init_machine,
MACHINE_END
/*
- * linux/arch/arm/mach-iop32x/irq.c
+ * arch/arm/mach-iop32x/irq.c
*
* Generic IOP32X IRQ handling functionality
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
- * Added IOP3XX chipset and IQ80321 board masking code.
- *
*/
+
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/list.h>
-
#include <asm/mach/irq.h>
#include <asm/irq.h>
#include <asm/hardware.h>
-
#include <asm/mach-types.h>
-static u32 iop321_mask /* = 0 */;
+static u32 iop32x_mask;
static inline void intctl_write(u32 val)
{
iop3xx_cp6_enable();
- asm volatile("mcr p6,0,%0,c0,c0,0"::"r" (val));
+ asm volatile("mcr p6, 0, %0, c0, c0, 0" : : "r" (val));
iop3xx_cp6_disable();
}
static inline void intstr_write(u32 val)
{
iop3xx_cp6_enable();
- asm volatile("mcr p6,0,%0,c4,c0,0"::"r" (val));
+ asm volatile("mcr p6, 0, %0, c4, c0, 0" : : "r" (val));
iop3xx_cp6_disable();
}
static void
-iop321_irq_mask (unsigned int irq)
+iop32x_irq_mask(unsigned int irq)
{
-
- iop321_mask &= ~(1 << irq);
-
- intctl_write(iop321_mask);
+ iop32x_mask &= ~(1 << irq);
+ intctl_write(iop32x_mask);
}
static void
-iop321_irq_unmask (unsigned int irq)
+iop32x_irq_unmask(unsigned int irq)
{
- iop321_mask |= (1 << irq);
-
- intctl_write(iop321_mask);
+ iop32x_mask |= 1 << irq;
+ intctl_write(iop32x_mask);
}
struct irq_chip ext_chip = {
- .name = "IOP",
- .ack = iop321_irq_mask,
- .mask = iop321_irq_mask,
- .unmask = iop321_irq_unmask,
+ .name = "IOP32x",
+ .ack = iop32x_irq_mask,
+ .mask = iop32x_irq_mask,
+ .unmask = iop32x_irq_unmask,
};
-void __init iop321_init_irq(void)
+void __init iop32x_init_irq(void)
{
- unsigned int i;
+ int i;
- intctl_write(0); // disable all interrupts
- intstr_write(0); // treat all as IRQ
- if(machine_is_iq80321() ||
- machine_is_iq31244()) // all interrupts are inputs to chip
+ intctl_write(0);
+ intstr_write(0);
+ if (machine_is_iq80321() ||
+ machine_is_iq31244())
*IOP3XX_PCIIRSR = 0x0f;
- for(i = 0; i < NR_IRQS; i++)
- {
+ for (i = 0; i < NR_IRQS; i++) {
set_irq_chip(i, &ext_chip);
set_irq_handler(i, do_level_IRQ);
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
-
}
}
-
if (slot == 1 && pin == 1) {
/* PCI-X Slot INTA */
- irq = IRQ_IOP331_XINT1;
+ irq = IRQ_IOP33X_XINT1;
} else if (slot == 1 && pin == 2) {
/* PCI-X Slot INTB */
- irq = IRQ_IOP331_XINT2;
+ irq = IRQ_IOP33X_XINT2;
} else if (slot == 1 && pin == 3) {
/* PCI-X Slot INTC */
- irq = IRQ_IOP331_XINT3;
+ irq = IRQ_IOP33X_XINT3;
} else if (slot == 1 && pin == 4) {
/* PCI-X Slot INTD */
- irq = IRQ_IOP331_XINT0;
+ irq = IRQ_IOP33X_XINT0;
} else if (slot == 2) {
/* GigE */
- irq = IRQ_IOP331_XINT2;
+ irq = IRQ_IOP33X_XINT2;
} else {
printk(KERN_ERR "iq80331_pci_map_irq() called for unknown "
"device PCI:%d:%d:%d\n", dev->bus->number,
.io_pg_offst = ((0xfffff000) >> 18) & 0xfffc,
.boot_params = 0x00000100,
.map_io = iop3xx_map_io,
- .init_irq = iop331_init_irq,
+ .init_irq = iop33x_init_irq,
.timer = &iq80331_timer,
.init_machine = iq80331_init_machine,
MACHINE_END
if (slot == 4 && pin == 1) {
/* PCI-X Slot INTA */
- irq = IRQ_IOP331_XINT0;
+ irq = IRQ_IOP33X_XINT0;
} else if (slot == 4 && pin == 2) {
/* PCI-X Slot INTB */
- irq = IRQ_IOP331_XINT1;
+ irq = IRQ_IOP33X_XINT1;
} else if (slot == 4 && pin == 3) {
/* PCI-X Slot INTC */
- irq = IRQ_IOP331_XINT2;
+ irq = IRQ_IOP33X_XINT2;
} else if (slot == 4 && pin == 4) {
/* PCI-X Slot INTD */
- irq = IRQ_IOP331_XINT3;
+ irq = IRQ_IOP33X_XINT3;
} else if (slot == 6) {
/* GigE */
- irq = IRQ_IOP331_XINT2;
+ irq = IRQ_IOP33X_XINT2;
} else {
printk(KERN_ERR "iq80332_pci_map_irq() called for unknown "
"device PCI:%d:%d:%d\n", dev->bus->number,
.io_pg_offst = ((0xfffff000) >> 18) & 0xfffc,
.boot_params = 0x00000100,
.map_io = iop3xx_map_io,
- .init_irq = iop331_init_irq,
+ .init_irq = iop33x_init_irq,
.timer = &iq80332_timer,
.init_machine = iq80332_init_machine,
MACHINE_END
/*
- * linux/arch/arm/mach-iop33x/irq.c
+ * arch/arm/mach-iop33x/irq.c
*
* Generic IOP331 IRQ handling functionality
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
- *
*/
+
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/list.h>
-
#include <asm/mach/irq.h>
#include <asm/irq.h>
#include <asm/hardware.h>
-
#include <asm/mach-types.h>
-static u32 iop331_mask0 = 0;
-static u32 iop331_mask1 = 0;
+static u32 iop33x_mask0;
+static u32 iop33x_mask1;
-static inline void intctl_write0(u32 val)
+static inline void intctl0_write(u32 val)
{
- // INTCTL0
iop3xx_cp6_enable();
- asm volatile("mcr p6,0,%0,c0,c0,0"::"r" (val));
+ asm volatile("mcr p6, 0, %0, c0, c0, 0" : : "r" (val));
iop3xx_cp6_disable();
}
-static inline void intctl_write1(u32 val)
+static inline void intctl1_write(u32 val)
{
- // INTCTL1
iop3xx_cp6_enable();
- asm volatile("mcr p6,0,%0,c1,c0,0"::"r" (val));
+ asm volatile("mcr p6, 0, %0, c1, c0, 0" : : "r" (val));
iop3xx_cp6_disable();
}
-static inline void intstr_write0(u32 val)
+static inline void intstr0_write(u32 val)
{
- // INTSTR0
iop3xx_cp6_enable();
- asm volatile("mcr p6,0,%0,c2,c0,0"::"r" (val));
+ asm volatile("mcr p6, 0, %0, c2, c0, 0" : : "r" (val));
iop3xx_cp6_disable();
}
-static inline void intstr_write1(u32 val)
+static inline void intstr1_write(u32 val)
{
- // INTSTR1
iop3xx_cp6_enable();
- asm volatile("mcr p6,0,%0,c3,c0,0"::"r" (val));
+ asm volatile("mcr p6, 0, %0, c3, c0, 0" : : "r" (val));
iop3xx_cp6_disable();
}
}
static void
-iop331_irq_mask1 (unsigned int irq)
+iop33x_irq_mask1 (unsigned int irq)
{
- iop331_mask0 &= ~(1 << irq);
- intctl_write0(iop331_mask0);
+ iop33x_mask0 &= ~(1 << irq);
+ intctl0_write(iop33x_mask0);
}
static void
-iop331_irq_mask2 (unsigned int irq)
+iop33x_irq_mask2 (unsigned int irq)
{
- iop331_mask1 &= ~(1 << (irq - 32));
- intctl_write1(iop331_mask1);
+ iop33x_mask1 &= ~(1 << (irq - 32));
+ intctl1_write(iop33x_mask1);
}
static void
-iop331_irq_unmask1(unsigned int irq)
+iop33x_irq_unmask1(unsigned int irq)
{
- iop331_mask0 |= (1 << irq);
- intctl_write0(iop331_mask0);
+ iop33x_mask0 |= 1 << irq;
+ intctl0_write(iop33x_mask0);
}
static void
-iop331_irq_unmask2(unsigned int irq)
+iop33x_irq_unmask2(unsigned int irq)
{
- iop331_mask1 |= (1 << (irq - 32));
- intctl_write1(iop331_mask1);
+ iop33x_mask1 |= (1 << (irq - 32));
+ intctl1_write(iop33x_mask1);
}
-struct irq_chip iop331_irqchip1 = {
- .name = "IOP-1",
- .ack = iop331_irq_mask1,
- .mask = iop331_irq_mask1,
- .unmask = iop331_irq_unmask1,
+struct irq_chip iop33x_irqchip1 = {
+ .name = "IOP33x-1",
+ .ack = iop33x_irq_mask1,
+ .mask = iop33x_irq_mask1,
+ .unmask = iop33x_irq_unmask1,
};
-struct irq_chip iop331_irqchip2 = {
- .name = "IOP-2",
- .ack = iop331_irq_mask2,
- .mask = iop331_irq_mask2,
- .unmask = iop331_irq_unmask2,
+struct irq_chip iop33x_irqchip2 = {
+ .name = "IOP33x-2",
+ .ack = iop33x_irq_mask2,
+ .mask = iop33x_irq_mask2,
+ .unmask = iop33x_irq_unmask2,
};
-void __init iop331_init_irq(void)
+void __init iop33x_init_irq(void)
{
- unsigned int i;
+ int i;
- intctl_write0(0); // disable all interrupts
- intctl_write1(0);
- intstr_write0(0); // treat all as IRQ
- intstr_write1(0);
+ intctl0_write(0);
+ intctl1_write(0);
+ intstr0_write(0);
+ intstr1_write(0);
intbase_write(0);
intsize_write(1);
- if(machine_is_iq80331()) // all interrupts are inputs to chip
+ if (machine_is_iq80331())
*IOP3XX_PCIIRSR = 0x0f;
- for(i = 0; i < NR_IRQS; i++)
- {
- set_irq_chip(i, (i < 32) ? &iop331_irqchip1 : &iop331_irqchip2);
+ for (i = 0; i < NR_IRQS; i++) {
+ set_irq_chip(i, (i < 32) ? &iop33x_irqchip1 : &iop33x_irqchip2);
set_irq_handler(i, do_level_IRQ);
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
}
}
-
/*
- * linux/arch/arm/mach-iop33x/uart.c
+ * arch/arm/mach-iop33x/uart.c
*
* Author: Dave Jiang (dave.jiang@intel.com)
* Copyright (C) 2004 Intel Corporation.
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/serial_8250.h>
-
#include <asm/io.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#define IOP331_UART_XTAL 33334000
+#define IOP33X_UART_XTAL 33334000
static struct plat_serial8250_port iop33x_uart0_data[] = {
{
- .membase = (char *)IOP331_UART0_VIRT,
- .mapbase = IOP331_UART0_PHYS,
- .irq = IRQ_IOP331_UART0,
- .uartclk = IOP331_UART_XTAL,
+ .membase = (char *)IOP33X_UART0_VIRT,
+ .mapbase = IOP33X_UART0_PHYS,
+ .irq = IRQ_IOP33X_UART0,
+ .uartclk = IOP33X_UART_XTAL,
.regshift = 2,
.iotype = UPIO_MEM,
.flags = UPF_SKIP_TEST,
static struct resource iop33x_uart0_resources[] = {
[0] = {
- .start = IOP331_UART0_PHYS,
- .end = IOP331_UART0_PHYS + 0x3f,
+ .start = IOP33X_UART0_PHYS,
+ .end = IOP33X_UART0_PHYS + 0x3f,
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = IRQ_IOP331_UART0,
- .end = IRQ_IOP331_UART0,
+ .start = IRQ_IOP33X_UART0,
+ .end = IRQ_IOP33X_UART0,
.flags = IORESOURCE_IRQ,
},
};
static struct resource iop33x_uart1_resources[] = {
[0] = {
- .start = IOP331_UART1_PHYS,
- .end = IOP331_UART1_PHYS + 0x3f,
+ .start = IOP33X_UART1_PHYS,
+ .end = IOP33X_UART1_PHYS + 0x3f,
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = IRQ_IOP331_UART1,
- .end = IRQ_IOP331_UART1,
+ .start = IRQ_IOP33X_UART1,
+ .end = IRQ_IOP33X_UART1,
.flags = IORESOURCE_IRQ,
},
};
static struct plat_serial8250_port iop33x_uart1_data[] = {
{
- .membase = (char *)IOP331_UART1_VIRT,
- .mapbase = IOP331_UART1_PHYS,
- .irq = IRQ_IOP331_UART1,
- .uartclk = IOP331_UART_XTAL,
+ .membase = (char *)IOP33X_UART1_VIRT,
+ .mapbase = IOP33X_UART1_PHYS,
+ .irq = IRQ_IOP33X_UART1,
+ .uartclk = IOP33X_UART_XTAL,
.regshift = 2,
.iotype = UPIO_MEM,
.flags = UPF_SKIP_TEST,
#define XSCALE_PMU_IRQ IRQ_XS80200_PMU
#endif
#ifdef CONFIG_ARCH_IOP32X
-#define XSCALE_PMU_IRQ IRQ_IOP321_CORE_PMU
+#define XSCALE_PMU_IRQ IRQ_IOP32X_CORE_PMU
#endif
#ifdef CONFIG_ARCH_IOP33X
-#define XSCALE_PMU_IRQ IRQ_IOP331_CORE_PMU
+#define XSCALE_PMU_IRQ IRQ_IOP33X_CORE_PMU
#endif
#ifdef CONFIG_ARCH_PXA
#define XSCALE_PMU_IRQ IRQ_PMU
/*
* There are two versions of the PMU in current XScale processors
* with differing register layouts and number of performance counters.
- * e.g. IOP321 is xsc1 whilst IOP331 is xsc2.
+ * e.g. IOP32x is xsc1 whilst IOP33x is xsc2.
* We detect which register layout to use in xscale_detect_pmu()
*/
enum { PMU_XSC1, PMU_XSC2 };
#include <asm/mach/arch.h>
#ifdef CONFIG_ARCH_IOP32X
-#define IRQ_IOP3XX_I2C_0 IRQ_IOP321_I2C_0
-#define IRQ_IOP3XX_I2C_1 IRQ_IOP321_I2C_1
+#define IRQ_IOP3XX_I2C_0 IRQ_IOP32X_I2C_0
+#define IRQ_IOP3XX_I2C_1 IRQ_IOP32X_I2C_1
#endif
#ifdef CONFIG_ARCH_IOP33X
-#define IRQ_IOP3XX_I2C_0 IRQ_IOP331_I2C_0
-#define IRQ_IOP3XX_I2C_1 IRQ_IOP331_I2C_1
+#define IRQ_IOP3XX_I2C_0 IRQ_IOP33X_I2C_0
+#define IRQ_IOP3XX_I2C_1 IRQ_IOP33X_I2C_1
#endif
static struct resource iop3xx_i2c0_resources[] = {
#include <asm/mach/time.h>
#ifdef CONFIG_ARCH_IOP32X
-#define IRQ_IOP3XX_TIMER0 IRQ_IOP321_TIMER0
+#define IRQ_IOP3XX_TIMER0 IRQ_IOP32X_TIMER0
#else
#ifdef CONFIG_ARCH_IOP33X
-#define IRQ_IOP3XX_TIMER0 IRQ_IOP331_TIMER0
+#define IRQ_IOP3XX_TIMER0 IRQ_IOP33X_TIMER0
#endif
#endif
-/* linux/include/asm-arm/arch-iop32x/debug-macro.S
+/*
+ * include/asm-arm/arch-iop32x/debug-macro.S
*
* Debugging macro include header
*
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ * Copyright (C) 1994-1999 Russell King
+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
-*/
+ */
- .macro addruart,rx
- mov \rx, #0xfe000000 @ physical
+ .macro addruart, rx
+ mov \rx, #0xfe000000 @ physical as well as virtual
orr \rx, \rx, #0x00800000 @ location of the UART
.endm
/*
- * linux/include/asm-arm/arch-iop32x/dma.h
+ * include/asm-arm/arch-iop32x/dma.h
*
- * Copyright (C) 2004 Intel Corp.
+ * Copyright (C) 2004 Intel Corp.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
*
* Low-level IRQ helper macros for IOP32x-based platforms
*
- * This file is licensed under the terms of the GNU General Public
+ * This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/irqs.h>
+#include <asm/arch/iop32x.h>
- .macro disable_fiq
+ .macro disable_fiq
.endm
- /*
- * Note: only deal with normal interrupts, not FIQ
- */
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \base, =IOP3XX_REG_ADDR(0x07D8)
ldr \irqstat, [\base] @ Read IINTSRC
cmp \irqstat, #0
/*
- * linux/include/asm-arm/arch-iop32x/hardware.h
+ * include/asm-arm/arch-iop32x/hardware.h
*/
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
+
+#ifndef __HARDWARE_H
+#define __HARDWARE_H
#include <asm/types.h>
* the IO resources.
*
* The PCI IO space is located at virtual 0xfe000000 from physical
- * 0x90000000. The PCI BARs must be programmed with physical addresses,
- * but when we read them, we convert them to virtual addresses. See
- * arch/arm/mach-iop3xx/iop3xx-pci.c
+ * 0x90000000. The PCI BARs must be programmed with physical addresses,
+ * but when we read them, we convert them to virtual addresses. See
+ * arch/arm/plat-iop/pci.c.
*/
-
#define pcibios_assign_all_busses() 1
#define PCIBIOS_MIN_IO 0x00000000
#define PCIBIOS_MIN_MEM 0x00000000
+#ifndef __ASSEMBLY__
+void iop32x_init_irq(void);
+#endif
+
/*
* Generic chipset bits
- *
*/
-#include "iop321.h"
+#include "iop32x.h"
/*
* Board specific bits
#include "iq80321.h"
#include "iq31244.h"
-#endif /* _ASM_ARCH_HARDWARE_H */
+
+#endif
/*
- * linux/include/asm-arm/arch-iop32x/io.h
+ * include/asm-arm/arch-iop32x/io.h
*
- * Copyright (C) 2001 MontaVista Software, Inc.
+ * Copyright (C) 2001 MontaVista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
+#ifndef __IO_H
+#define __IO_H
#include <asm/hardware.h>
-#define IO_SPACE_LIMIT 0xffffffff
+#define IO_SPACE_LIMIT 0xffffffff
#define __io(p) ((void __iomem *)(p))
#define __mem_pci(a) (a)
+
#endif
+++ /dev/null
-/*
- * linux/include/asm/arch-iop32x/iop321.h
- *
- * Intel IOP321 Chip definitions
- *
- * Author: Rory Bolt <rorybolt@pacbell.net>
- * Copyright (C) 2002 Rory Bolt
- * Copyright (C) 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef _IOP321_HW_H_
-#define _IOP321_HW_H_
-
-
-/*
- * This is needed for mixed drivers that need to work on all
- * IOP3xx variants but behave slightly differently on each.
- */
-#ifndef __ASSEMBLY__
-#define iop_is_321() 1
-#endif
-
-/*
- * IOP321 chipset registers
- */
-#define IOP321_VIRT_MEM_BASE 0xfeffe000 /* chip virtual mem address*/
-#define IOP321_PHYS_MEM_BASE 0xffffe000 /* chip physical memory address */
-#define IOP321_REG_ADDR(reg) (IOP321_VIRT_MEM_BASE | (reg))
-
-/* Reserved 0x00000000 through 0x000000FF */
-
-/* Address Translation Unit 0x00000100 through 0x000001FF */
-
-/* Messaging Unit 0x00000300 through 0x000003FF */
-
-/* DMA Controller 0x00000400 through 0x000004FF */
-
-/* Memory controller 0x00000500 through 0x0005FF */
-
-/* Peripheral bus interface unit 0x00000680 through 0x0006FF */
-
-/* Peripheral performance monitoring unit 0x00000700 through 0x00077F */
-
-/* Internal arbitration unit 0x00000780 through 0x0007BF */
-#define IOP321_IACR (volatile u32 *)IOP321_REG_ADDR(0x00000780)
-#define IOP321_MTTR1 (volatile u32 *)IOP321_REG_ADDR(0x00000784)
-#define IOP321_MTTR2 (volatile u32 *)IOP321_REG_ADDR(0x00000788)
-
-/* General Purpose I/O Registers */
-#define IOP321_GPOE (volatile u32 *)IOP321_REG_ADDR(0x000007C4)
-#define IOP321_GPID (volatile u32 *)IOP321_REG_ADDR(0x000007C8)
-#define IOP321_GPOD (volatile u32 *)IOP321_REG_ADDR(0x000007CC)
-
-/* Interrupt Controller */
-#define IOP321_INTCTL (volatile u32 *)IOP321_REG_ADDR(0x000007D0)
-#define IOP321_INTSTR (volatile u32 *)IOP321_REG_ADDR(0x000007D4)
-#define IOP321_IINTSRC (volatile u32 *)IOP321_REG_ADDR(0x000007D8)
-#define IOP321_FINTSRC (volatile u32 *)IOP321_REG_ADDR(0x000007DC)
-
-/* Application accelerator unit 0x00000800 - 0x000008FF */
-
-/* SSP serial port unit 0x00001600 - 0x0000167F */
-/* I2C bus interface unit 0x00001680 - 0x000016FF */
-
-/* for I2C bit defs see drivers/i2c/i2c-iop3xx.h */
-
-/*
- * Peripherals that are shared between the iop32x and iop33x but
- * located at different addresses.
- */
-#define IOP3XX_GPIO_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07c0 + (reg))
-#define IOP3XX_TIMER_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07e0 + (reg))
-
-#include <asm/hardware/iop3xx.h>
-
-
-#ifndef __ASSEMBLY__
-extern void iop321_init_irq(void);
-extern void iop321_time_init(void);
-#endif
-
-#endif // _IOP321_HW_H_
--- /dev/null
+/*
+ * include/asm-arm/arch-iop32x/iop32x.h
+ *
+ * Intel IOP32X Chip definitions
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ * Copyright (C) 2004 Intel Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __IOP32X_H
+#define __IOP32X_H
+
+/*
+ * Peripherals that are shared between the iop32x and iop33x but
+ * located at different addresses.
+ */
+#define IOP3XX_GPIO_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07c0 + (reg))
+#define IOP3XX_TIMER_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07e0 + (reg))
+
+#include <asm/hardware/iop3xx.h>
+
+
+#endif
/*
- * linux/include/asm/arch-iop32x/iq31244.h
+ * include/asm-arm/arch-iop32x/iq31244.h
*
* Intel IQ31244 evaluation board registers
*/
-#ifndef _IQ31244_H_
-#define _IQ31244_H_
+#ifndef __IQ31244_H
+#define __IQ31244_H
#define IQ31244_UART 0xfe800000 /* UART #1 */
#define IQ31244_7SEG_1 0xfe840000 /* 7-Segment MSB */
#define IQ31244_BATT_STAT 0xfe8f0000 /* Battery Status */
-#endif // _IQ31244_H_
+#endif
/*
- * linux/include/asm/arch-iop32x/iq80321.h
+ * include/asm-arm/arch-iop32x/iq80321.h
*
* Intel IQ80321 evaluation board registers
*/
-#ifndef _IQ80321_H_
-#define _IQ80321_H_
+#ifndef __IQ80321_H
+#define __IQ80321_H
#define IQ80321_UART 0xfe800000 /* UART #1 */
#define IQ80321_7SEG_1 0xfe840000 /* 7-Segment MSB */
#define IQ80321_BATT_STAT 0xfe8f0000 /* Battery Status */
-#endif // _IQ80321_H_
+#endif
/*
- * linux/include/asm-arm/arch-iop32x/irqs.h
+ * include/asm-arm/arch-iop32x/irqs.h
*
* Author: Rory Bolt <rorybolt@pacbell.net>
* Copyright: (C) 2002 Rory Bolt
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
*/
-#ifndef _IRQS_H_
-#define _IRQS_H_
+
+#ifndef __IRQS_H
+#define __IRQS_H
/*
* IOP80321 chipset interrupts
*/
-#define IRQ_IOP321_DMA0_EOT 0
-#define IRQ_IOP321_DMA0_EOC 1
-#define IRQ_IOP321_DMA1_EOT 2
-#define IRQ_IOP321_DMA1_EOC 3
-#define IRQ_IOP321_AA_EOT 6
-#define IRQ_IOP321_AA_EOC 7
-#define IRQ_IOP321_CORE_PMON 8
-#define IRQ_IOP321_TIMER0 9
-#define IRQ_IOP321_TIMER1 10
-#define IRQ_IOP321_I2C_0 11
-#define IRQ_IOP321_I2C_1 12
-#define IRQ_IOP321_MESSAGING 13
-#define IRQ_IOP321_ATU_BIST 14
-#define IRQ_IOP321_PERFMON 15
-#define IRQ_IOP321_CORE_PMU 16
-#define IRQ_IOP321_BIU_ERR 17
-#define IRQ_IOP321_ATU_ERR 18
-#define IRQ_IOP321_MCU_ERR 19
-#define IRQ_IOP321_DMA0_ERR 20
-#define IRQ_IOP321_DMA1_ERR 21
-#define IRQ_IOP321_AA_ERR 23
-#define IRQ_IOP321_MSG_ERR 24
-#define IRQ_IOP321_SSP 25
-#define IRQ_IOP321_XINT0 27
-#define IRQ_IOP321_XINT1 28
-#define IRQ_IOP321_XINT2 29
-#define IRQ_IOP321_XINT3 30
-#define IRQ_IOP321_HPI 31
+#define IRQ_IOP32X_DMA0_EOT 0
+#define IRQ_IOP32X_DMA0_EOC 1
+#define IRQ_IOP32X_DMA1_EOT 2
+#define IRQ_IOP32X_DMA1_EOC 3
+#define IRQ_IOP32X_AA_EOT 6
+#define IRQ_IOP32X_AA_EOC 7
+#define IRQ_IOP32X_CORE_PMON 8
+#define IRQ_IOP32X_TIMER0 9
+#define IRQ_IOP32X_TIMER1 10
+#define IRQ_IOP32X_I2C_0 11
+#define IRQ_IOP32X_I2C_1 12
+#define IRQ_IOP32X_MESSAGING 13
+#define IRQ_IOP32X_ATU_BIST 14
+#define IRQ_IOP32X_PERFMON 15
+#define IRQ_IOP32X_CORE_PMU 16
+#define IRQ_IOP32X_BIU_ERR 17
+#define IRQ_IOP32X_ATU_ERR 18
+#define IRQ_IOP32X_MCU_ERR 19
+#define IRQ_IOP32X_DMA0_ERR 20
+#define IRQ_IOP32X_DMA1_ERR 21
+#define IRQ_IOP32X_AA_ERR 23
+#define IRQ_IOP32X_MSG_ERR 24
+#define IRQ_IOP32X_SSP 25
+#define IRQ_IOP32X_XINT0 27
+#define IRQ_IOP32X_XINT1 28
+#define IRQ_IOP32X_XINT2 29
+#define IRQ_IOP32X_XINT3 30
+#define IRQ_IOP32X_HPI 31
#define NR_IRQS 32
-#endif // _IRQ_H_
+#endif
/*
- * linux/include/asm-arm/arch-iop32x/memory.h
+ * include/asm-arm/arch-iop32x/memory.h
*/
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
+#ifndef __MEMORY_H
+#define __MEMORY_H
#include <asm/hardware.h>
* bus_to_virt: Used to convert an address for DMA operations
* to an address that the kernel can use.
*/
-
#define __virt_to_bus(x) (((__virt_to_phys(x)) & ~(*IOP3XX_IATVR2)) | ((*IOP3XX_IABAR2) & 0xfffffff0))
#define __bus_to_virt(x) (__phys_to_virt(((x) & ~(*IOP3XX_IALR2)) | ( *IOP3XX_IATVR2)))
/*
- * linux/include/asm-arm/arch-iop32x/system.h
+ * include/asm-arm/arch-iop32x/system.h
*
- * Copyright (C) 2001 MontaVista Software, Inc.
+ * Copyright (C) 2001 MontaVista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
cpu_do_idle();
}
-
static inline void arch_reset(char mode)
{
- *IOP3XX_PCSR = 0x30;
+ *IOP3XX_PCSR = 0x30;
- if ( 1 && mode == 's') {
- /* Jump into ROM at address 0 */
- cpu_reset(0);
- } else {
- /* No on-chip reset capability */
- cpu_reset(0);
- }
+ /* Jump into ROM at address 0 */
+ cpu_reset(0);
}
-
/*
- * linux/include/asm-arm/arch-iop32x/timex.h
+ * include/asm-arm/arch-iop32x/timex.h
*
- * IOP3xx architecture timex specifications
+ * IOP32x architecture timex specifications
*/
+
#include <asm/hardware.h>
#define CLOCK_TICK_RATE (100 * HZ)
/*
- * linux/include/asm-arm/arch-iop32x/uncompress.h
+ * include/asm-arm/arch-iop32x/uncompress.h
*/
+
#include <asm/types.h>
#include <asm/mach-types.h>
#include <linux/serial_reg.h>
static volatile u8 *uart_base;
-#define TX_DONE (UART_LSR_TEMT|UART_LSR_THRE)
+#define TX_DONE (UART_LSR_TEMT | UART_LSR_THRE)
static inline void putc(char c)
{
while ((uart_base[UART_LSR] & TX_DONE) != TX_DONE)
barrier();
- *uart_base = c;
+ uart_base[UART_TX] = c;
}
static inline void flush(void)
/*
- * linux/include/asm-arm/arch-iop32x/vmalloc.h
+ * include/asm-arm/arch-iop32x/vmalloc.h
*/
-/*
- * Just any arbitrary offset to the start of the vmalloc VM area: the
- * current 8MB value just means that there will be a 8MB "hole" after the
- * physical memory until the kernel virtual memory starts. That means that
- * any out-of-bounds memory accesses will hopefully be caught.
- * The vmalloc() routines leaves a hole of 4kB between each vmalloced
- * area for the same reason. ;)
- */
-//#define VMALLOC_END (0xe8000000)
-/* increase usable physical RAM to ~992M per RMK */
-#define VMALLOC_END (0xfe000000)
-
+#define VMALLOC_END 0xfe000000
-/* linux/include/asm-arm/arch-iop33x/debug-macro.S
+/*
+ * include/asm-arm/arch-iop33x/debug-macro.S
*
* Debugging macro include header
*
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ * Copyright (C) 1994-1999 Russell King
+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
-*/
+ */
- .macro addruart,rx
+ .macro addruart, rx
mrc p15, 0, \rx, c1, c0
tst \rx, #1 @ mmu enabled?
moveq \rx, #0xff000000 @ physical
/*
- * linux/include/asm-arm/arch-iop33x/dma.h
+ * include/asm-arm/arch-iop33x/dma.h
*
- * Copyright (C) 2004 Intel Corp.
+ * Copyright (C) 2004 Intel Corp.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
*
* Low-level IRQ helper macros for IOP33x-based platforms
*
- * This file is licensed under the terms of the GNU General Public
+ * This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/irqs.h>
+#include <asm/arch/iop33x.h>
- .macro disable_fiq
+ .macro disable_fiq
.endm
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \base, =IOP3XX_REG_ADDR(0x07C8)
ldr \irqstat, [\base] @ Read IINTVEC
cmp \irqstat, #0
/*
- * linux/include/asm-arm/arch-iop33x/hardware.h
+ * include/asm-arm/arch-iop33x/hardware.h
*/
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
+
+#ifndef __HARDWARE_H
+#define __HARDWARE_H
#include <asm/types.h>
* The PCI IO space is located at virtual 0xfe000000 from physical
* 0x90000000. The PCI BARs must be programmed with physical addresses,
* but when we read them, we convert them to virtual addresses. See
- * arch/arm/mach-iop33x/pci.c
+ * arch/arm/mach-iop3xx/iop3xx-pci.c
*/
-
-#define pcibios_assign_all_busses() 1
+#define pcibios_assign_all_busses() 1
#define PCIBIOS_MIN_IO 0x00000000
#define PCIBIOS_MIN_MEM 0x00000000
#ifndef __ASSEMBLY__
+void iop33x_init_irq(void);
+
extern struct platform_device iop33x_uart0_device;
extern struct platform_device iop33x_uart1_device;
#endif
* Generic chipset bits
*
*/
-#include "iop331.h"
+#include "iop33x.h"
/*
* Board specific bits
#include "iq80331.h"
#include "iq80332.h"
-#endif /* _ASM_ARCH_HARDWARE_H */
+
+#endif
/*
- * linux/include/asm-arm/arch-iop33x/io.h
+ * include/asm-arm/arch-iop33x/io.h
*
- * Copyright (C) 2001 MontaVista Software, Inc.
+ * Copyright (C) 2001 MontaVista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
+#ifndef __IO_H
+#define __IO_H
#include <asm/hardware.h>
-#define IO_SPACE_LIMIT 0xffffffff
-
+#define IO_SPACE_LIMIT 0xffffffff
#define __io(p) ((void __iomem *)(p))
#define __mem_pci(a) (a)
+
#endif
+++ /dev/null
-/*
- * linux/include/asm/arch-iop33x/iop331.h
- *
- * Intel IOP331 Chip definitions
- *
- * Author: Dave Jiang (dave.jiang@intel.com)
- * Copyright (C) 2003, 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef _IOP331_HW_H_
-#define _IOP331_HW_H_
-
-
-/*
- * This is needed for mixed drivers that need to work on all
- * IOP3xx variants but behave slightly differently on each.
- */
-#ifndef __ASSEMBLY__
-#define iop_is_331() 1
-#endif
-
-/*
- * IOP331 chipset registers
- */
-#define IOP331_VIRT_MEM_BASE 0xfeffe000 /* chip virtual mem address*/
-#define IOP331_PHYS_MEM_BASE 0xffffe000 /* chip physical memory address */
-#define IOP331_REG_ADDR(reg) (IOP331_VIRT_MEM_BASE | (reg))
-
-/* Reserved 0x00000000 through 0x000000FF */
-
-/* Address Translation Unit 0x00000100 through 0x000001FF */
-
-/* Messaging Unit 0x00000300 through 0x000003FF */
-
-/* DMA Controller 0x00000400 through 0x000004FF */
-
-/* Memory controller 0x00000500 through 0x0005FF */
-
-/* Peripheral bus interface unit 0x00000680 through 0x0006FF */
-
-/* Peripheral performance monitoring unit 0x00000700 through 0x00077F */
-/* Internal arbitration unit 0x00000780 through 0x0007BF */
-
-/* Interrupt Controller */
-#define IOP331_INTCTL0 (volatile u32 *)IOP331_REG_ADDR(0x00000790)
-#define IOP331_INTCTL1 (volatile u32 *)IOP331_REG_ADDR(0x00000794)
-#define IOP331_INTSTR0 (volatile u32 *)IOP331_REG_ADDR(0x00000798)
-#define IOP331_INTSTR1 (volatile u32 *)IOP331_REG_ADDR(0x0000079C)
-#define IOP331_IINTSRC0 (volatile u32 *)IOP331_REG_ADDR(0x000007A0)
-#define IOP331_IINTSRC1 (volatile u32 *)IOP331_REG_ADDR(0x000007A4)
-#define IOP331_FINTSRC0 (volatile u32 *)IOP331_REG_ADDR(0x000007A8)
-#define IOP331_FINTSRC1 (volatile u32 *)IOP331_REG_ADDR(0x000007AC)
-#define IOP331_IPR0 (volatile u32 *)IOP331_REG_ADDR(0x000007B0)
-#define IOP331_IPR1 (volatile u32 *)IOP331_REG_ADDR(0x000007B4)
-#define IOP331_IPR2 (volatile u32 *)IOP331_REG_ADDR(0x000007B8)
-#define IOP331_IPR3 (volatile u32 *)IOP331_REG_ADDR(0x000007BC)
-#define IOP331_INTBASE (volatile u32 *)IOP331_REG_ADDR(0x000007C0)
-#define IOP331_INTSIZE (volatile u32 *)IOP331_REG_ADDR(0x000007C4)
-#define IOP331_IINTVEC (volatile u32 *)IOP331_REG_ADDR(0x000007C8)
-#define IOP331_FINTVEC (volatile u32 *)IOP331_REG_ADDR(0x000007CC)
-
-
-/* Application accelerator unit 0x00000800 - 0x000008FF */
-
-#define IOP331_SPDSCR (volatile u32 *)IOP331_REG_ADDR(0x000015C0)
-#define IOP331_PPDSCR (volatile u32 *)IOP331_REG_ADDR(0x000015C8)
-/* SSP serial port unit 0x00001600 - 0x0000167F */
-
-/* I2C bus interface unit 0x00001680 - 0x000016FF */
-
-/* 0x00001700 through 0x0000172C UART 0 */
-
-/* Reserved 0x00001730 through 0x0000173F */
-
-/* 0x00001740 through 0x0000176C UART 1 */
-
-#define IOP331_UART0_PHYS (IOP331_PHYS_MEM_BASE | 0x00001700) /* UART #1 physical */
-#define IOP331_UART1_PHYS (IOP331_PHYS_MEM_BASE | 0x00001740) /* UART #2 physical */
-#define IOP331_UART0_VIRT (IOP331_VIRT_MEM_BASE | 0x00001700) /* UART #1 virtual addr */
-#define IOP331_UART1_VIRT (IOP331_VIRT_MEM_BASE | 0x00001740) /* UART #2 virtual addr */
-
-/* Reserved 0x00001770 through 0x0000177F */
-
-/* General Purpose I/O Registers */
-#define IOP331_GPOE (volatile u32 *)IOP331_REG_ADDR(0x00001780)
-#define IOP331_GPID (volatile u32 *)IOP331_REG_ADDR(0x00001784)
-#define IOP331_GPOD (volatile u32 *)IOP331_REG_ADDR(0x00001788)
-
-/* Reserved 0x0000178c through 0x000019ff */
-
-/*
- * Peripherals that are shared between the iop32x and iop33x but
- * located at different addresses.
- */
-#define IOP3XX_GPIO_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x1780 + (reg))
-#define IOP3XX_TIMER_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07d0 + (reg))
-
-#include <asm/hardware/iop3xx.h>
-
-
-#ifndef __ASSEMBLY__
-extern void iop331_init_irq(void);
-extern void iop331_time_init(void);
-#endif
-
-#endif // _IOP331_HW_H_
--- /dev/null
+/*
+ * include/asm-arm/arch-iop33x/iop33x.h
+ *
+ * Intel IOP33X Chip definitions
+ *
+ * Author: Dave Jiang (dave.jiang@intel.com)
+ * Copyright (C) 2003, 2004 Intel Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __IOP33X_H
+#define __IOP33X_H
+
+/*
+ * Peripherals that are shared between the iop32x and iop33x but
+ * located at different addresses.
+ */
+#define IOP3XX_GPIO_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x1780 + (reg))
+#define IOP3XX_TIMER_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07d0 + (reg))
+
+#include <asm/hardware/iop3xx.h>
+
+/* UARTs */
+#define IOP33X_UART0_PHYS (IOP3XX_PERIPHERAL_PHYS_BASE + 0x1700)
+#define IOP33X_UART0_VIRT (IOP3XX_PERIPHERAL_VIRT_BASE + 0x1700)
+#define IOP33X_UART1_PHYS (IOP3XX_PERIPHERAL_PHYS_BASE + 0x1740)
+#define IOP33X_UART1_VIRT (IOP3XX_PERIPHERAL_VIRT_BASE + 0x1740)
+
+
+#endif
/*
- * linux/include/asm/arch-iop33x/iq80331.h
+ * include/asm-arm/arch-iop33x/iq80331.h
*
* Intel IQ80331 evaluation board registers
*/
-#ifndef _IQ80331_H_
-#define _IQ80331_H_
+#ifndef __IQ80331_H
+#define __IQ80331_H
#define IQ80331_7SEG_1 0xce840000 /* 7-Segment MSB */
#define IQ80331_7SEG_0 0xce850000 /* 7-Segment LSB (WO) */
#define IQ80331_BATT_STAT 0xce8f0000 /* Battery Status */
-#endif // _IQ80331_H_
+#endif
/*
- * linux/include/asm/arch-iop33x/iq80332.h
+ * include/asm-arm/arch-iop33x/iq80332.h
*
* Intel IQ80332 evaluation board registers
*/
-#ifndef _IQ80332_H_
-#define _IQ80332_H_
+#ifndef __IQ80332_H
+#define __IQ80332_H
#define IQ80332_7SEG_1 0xce840000 /* 7-Segment MSB */
#define IQ80332_7SEG_0 0xce850000 /* 7-Segment LSB (WO) */
#define IQ80332_BATT_STAT 0xce8f0000 /* Battery Status */
-#endif // _IQ80332_H_
+#endif
/*
- * linux/include/asm-arm/arch-iop33x/irqs.h
+ * include/asm-arm/arch-iop33x/irqs.h
*
* Author: Dave Jiang (dave.jiang@intel.com)
* Copyright: (C) 2003 Intel Corp.
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
*/
-#ifndef _IRQS_H_
-#define _IRQS_H_
+
+#ifndef __IRQS_H
+#define __IRQS_H
/*
* IOP80331 chipset interrupts
*/
-#define IRQ_IOP331_DMA0_EOT 0
-#define IRQ_IOP331_DMA0_EOC 1
-#define IRQ_IOP331_DMA1_EOT 2
-#define IRQ_IOP331_DMA1_EOC 3
-#define IRQ_IOP331_AA_EOT 6
-#define IRQ_IOP331_AA_EOC 7
-#define IRQ_IOP331_TIMER0 8
-#define IRQ_IOP331_TIMER1 9
-#define IRQ_IOP331_I2C_0 10
-#define IRQ_IOP331_I2C_1 11
-#define IRQ_IOP331_MSG 12
-#define IRQ_IOP331_MSGIBQ 13
-#define IRQ_IOP331_ATU_BIST 14
-#define IRQ_IOP331_PERFMON 15
-#define IRQ_IOP331_CORE_PMU 16
-#define IRQ_IOP331_XINT0 24
-#define IRQ_IOP331_XINT1 25
-#define IRQ_IOP331_XINT2 26
-#define IRQ_IOP331_XINT3 27
-#define IRQ_IOP331_XINT8 32
-#define IRQ_IOP331_XINT9 33
-#define IRQ_IOP331_XINT10 34
-#define IRQ_IOP331_XINT11 35
-#define IRQ_IOP331_XINT12 36
-#define IRQ_IOP331_XINT13 37
-#define IRQ_IOP331_XINT14 38
-#define IRQ_IOP331_XINT15 39
-#define IRQ_IOP331_UART0 51
-#define IRQ_IOP331_UART1 52
-#define IRQ_IOP331_PBIE 53
-#define IRQ_IOP331_ATU_CRW 54
-#define IRQ_IOP331_ATU_ERR 55
-#define IRQ_IOP331_MCU_ERR 56
-#define IRQ_IOP331_DMA0_ERR 57
-#define IRQ_IOP331_DMA1_ERR 58
-#define IRQ_IOP331_AA_ERR 60
-#define IRQ_IOP331_MSG_ERR 62
-#define IRQ_IOP331_HPI 63
+#define IRQ_IOP33X_DMA0_EOT 0
+#define IRQ_IOP33X_DMA0_EOC 1
+#define IRQ_IOP33X_DMA1_EOT 2
+#define IRQ_IOP33X_DMA1_EOC 3
+#define IRQ_IOP33X_AA_EOT 6
+#define IRQ_IOP33X_AA_EOC 7
+#define IRQ_IOP33X_TIMER0 8
+#define IRQ_IOP33X_TIMER1 9
+#define IRQ_IOP33X_I2C_0 10
+#define IRQ_IOP33X_I2C_1 11
+#define IRQ_IOP33X_MSG 12
+#define IRQ_IOP33X_MSGIBQ 13
+#define IRQ_IOP33X_ATU_BIST 14
+#define IRQ_IOP33X_PERFMON 15
+#define IRQ_IOP33X_CORE_PMU 16
+#define IRQ_IOP33X_XINT0 24
+#define IRQ_IOP33X_XINT1 25
+#define IRQ_IOP33X_XINT2 26
+#define IRQ_IOP33X_XINT3 27
+#define IRQ_IOP33X_XINT8 32
+#define IRQ_IOP33X_XINT9 33
+#define IRQ_IOP33X_XINT10 34
+#define IRQ_IOP33X_XINT11 35
+#define IRQ_IOP33X_XINT12 36
+#define IRQ_IOP33X_XINT13 37
+#define IRQ_IOP33X_XINT14 38
+#define IRQ_IOP33X_XINT15 39
+#define IRQ_IOP33X_UART0 51
+#define IRQ_IOP33X_UART1 52
+#define IRQ_IOP33X_PBIE 53
+#define IRQ_IOP33X_ATU_CRW 54
+#define IRQ_IOP33X_ATU_ERR 55
+#define IRQ_IOP33X_MCU_ERR 56
+#define IRQ_IOP33X_DMA0_ERR 57
+#define IRQ_IOP33X_DMA1_ERR 58
+#define IRQ_IOP33X_AA_ERR 60
+#define IRQ_IOP33X_MSG_ERR 62
+#define IRQ_IOP33X_HPI 63
#define NR_IRQS 64
-#endif // _IRQ_H_
+#endif
/*
- * linux/include/asm-arm/arch-iop33x/memory.h
+ * include/asm-arm/arch-iop33x/memory.h
*/
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
+#ifndef __MEMORY_H
+#define __MEMORY_H
#include <asm/hardware.h>
/*
- * linux/include/asm-arm/arch-iop33x/system.h
+ * include/asm-arm/arch-iop33x/system.h
*
- * Copyright (C) 2001 MontaVista Software, Inc.
+ * Copyright (C) 2001 MontaVista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
cpu_do_idle();
}
-
static inline void arch_reset(char mode)
{
- *IOP3XX_PCSR = 0x30;
+ *IOP3XX_PCSR = 0x30;
- if ( 1 && mode == 's') {
- /* Jump into ROM at address 0 */
- cpu_reset(0);
- } else {
- /* No on-chip reset capability */
- cpu_reset(0);
- }
+ /* Jump into ROM at address 0 */
+ cpu_reset(0);
}
-
/*
- * linux/include/asm-arm/arch-iop33x/timex.h
+ * include/asm-arm/arch-iop33x/timex.h
*
* IOP3xx architecture timex specifications
*/
+
#include <asm/hardware.h>
#define CLOCK_TICK_RATE (100 * HZ)
/*
- * linux/include/asm-arm/arch-iop33x/uncompress.h
+ * include/asm-arm/arch-iop33x/uncompress.h
*/
+
#include <asm/types.h>
#include <asm/mach-types.h>
#include <linux/serial_reg.h>
static volatile u32 *uart_base;
-#define TX_DONE (UART_LSR_TEMT|UART_LSR_THRE)
+#define TX_DONE (UART_LSR_TEMT | UART_LSR_THRE)
static inline void putc(char c)
{
while ((uart_base[UART_LSR] & TX_DONE) != TX_DONE)
barrier();
- *uart_base = c;
+ uart_base[UART_TX] = c;
}
static inline void flush(void)
static __inline__ void __arch_decomp_setup(unsigned long arch_id)
{
if (machine_is_iq80331() || machine_is_iq80332())
- uart_base = (volatile u32 *)IOP331_UART0_PHYS;
+ uart_base = (volatile u32 *)IOP33X_UART0_PHYS;
else
uart_base = (volatile u32 *)0xfe800000;
}
/*
- * linux/include/asm-arm/arch-iop33x/vmalloc.h
+ * include/asm-arm/arch-iop33x/vmalloc.h
*/
-/*
- * Just any arbitrary offset to the start of the vmalloc VM area: the
- * current 8MB value just means that there will be a 8MB "hole" after the
- * physical memory until the kernel virtual memory starts. That means that
- * any out-of-bounds memory accesses will hopefully be caught.
- * The vmalloc() routines leaves a hole of 4kB between each vmalloced
- * area for the same reason. ;)
- */
-//#define VMALLOC_END (0xe8000000)
-/* increase usable physical RAM to ~992M per RMK */
-#define VMALLOC_END (0xfe000000)
-
+#define VMALLOC_END 0xfe000000
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff