Add core support for the Kendin/Micrel KS8695 processor family.
It is an ARM922-T based SoC with integrated USART, 4-port Ethernet
Switch, WAN Ethernet port, and optional PCI Host bridge, etc.
http://www.micrel.com/page.do?page=product-info/sys_on_chip.jsp
This patch is based on earlier patches from Lennert Buytenhek, Ben
Dooks and Greg Ungerer posted to the arm-linux-kernel mailing list in
March 2006; and Micrel's 2.6.9 port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If you have any questions or comments about the Linux kernel port
to this board, send e-mail to <sjhill@cotw.com>.
+config ARCH_KS8695
+ bool "Micrel/Kendin KS8695"
+ help
+ Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
+ System-on-Chip devices.
+
config ARCH_NS9XXX
bool "NetSilicon NS9xxx"
help
source "arch/arm/mach-davinci/Kconfig"
+source "arch/arm/mach-ks8695/Kconfig"
+
# Definitions to make life easier
config ARCH_ACORN
bool
bool
config PCI
- bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX
+ bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695
help
Find out whether you have a PCI motherboard. PCI is the name of a
bus system, i.e. the way the CPU talks to the other stuff inside
ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \
ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \
ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \
- ARCH_AT91 || MACH_TRIZEPS4 || ARCH_DAVINCI
+ ARCH_AT91 || MACH_TRIZEPS4 || ARCH_DAVINCI || \
+ ARCH_KS8695
help
If you say Y here, the LEDs on your machine will be used
to provide useful information about your current system status.
machine-$(CONFIG_ARCH_NS9XXX) := ns9xxx
textofs-$(CONFIG_ARCH_NS9XXX) := 0x00108000
machine-$(CONFIG_ARCH_DAVINCI) := davinci
+ machine-$(CONFIG_ARCH_KS8695) := ks8695
ifeq ($(CONFIG_ARCH_EBSA110),y)
# This is what happens if you forget the IOCS16 line.
--- /dev/null
+if ARCH_KS8695
+
+menu "Kendin/Micrel KS8695 Implementations"
+
+
+endmenu
+
+endif
--- /dev/null
+# arch/arm/mach-ks8695/Makefile
+#
+# Makefile for KS8695 architecture support
+#
+
+obj-y := cpu.o irq.o time.o devices.o
+obj-m :=
+obj-n :=
+obj- :=
+
+# PCI support is optional
+#obj-$(CONFIG_PCI) += pci.o
+
+# Board-specific support
--- /dev/null
+# Note: the following conditions must always be true:
+# ZRELADDR == virt_to_phys(TEXTADDR)
+# PARAMS_PHYS must be within 4MB of ZRELADDR
+# INITRD_PHYS must be in RAM
+
+ zreladdr-y := 0x00008000
+params_phys-y := 0x00000100
+initrd_phys-y := 0x00800000
--- /dev/null
+/*
+ * arch/arm/mach-ks8695/cpu.c
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 CPU support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <asm/arch/regs-sys.h>
+#include <asm/arch/regs-misc.h>
+
+
+static struct __initdata map_desc ks8695_io_desc[] = {
+ {
+ .virtual = KS8695_IO_VA,
+ .pfn = __phys_to_pfn(KS8695_IO_PA),
+ .length = KS8695_IO_SIZE,
+ .type = MT_DEVICE,
+ }
+};
+
+static void __init ks8695_processor_info(void)
+{
+ unsigned long id, rev;
+
+ id = __raw_readl(KS8695_MISC_VA + KS8695_DID);
+ rev = __raw_readl(KS8695_MISC_VA + KS8695_RID);
+
+ printk("KS8695 ID=%04lx SubID=%02lx Revision=%02lx\n", (id & DID_ID), (rev & RID_SUBID), (rev & RID_REVISION));
+}
+
+static unsigned int sysclk[8] = { 125000000, 100000000, 62500000, 50000000, 41700000, 33300000, 31300000, 25000000 };
+static unsigned int cpuclk[8] = { 166000000, 166000000, 83000000, 83000000, 55300000, 55300000, 41500000, 41500000 };
+
+static void __init ks8695_clock_info(void)
+{
+ unsigned int scdc = __raw_readl(KS8695_SYS_VA + KS8695_CLKCON) & CLKCON_SCDC;
+
+ printk("Clocks: System %u MHz, CPU %u MHz\n",
+ sysclk[scdc] / 1000000, cpuclk[scdc] / 1000000);
+}
+
+void __init ks8695_map_io(void)
+{
+ iotable_init(ks8695_io_desc, ARRAY_SIZE(ks8695_io_desc));
+
+ ks8695_processor_info();
+ ks8695_clock_info();
+}
--- /dev/null
+/*
+ * arch/arm/mach-ks8695/devices.c
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/platform_device.h>
+
+#include <asm/arch/regs-wan.h>
+#include <asm/arch/regs-lan.h>
+#include <asm/arch/regs-hpna.h>
+
+
+/* --------------------------------------------------------------------
+ * Ethernet
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ARM_KS8695_ETHER) || defined(CONFIG_ARM_KS8695_ETHER_MODULE)
+static u64 eth_dmamask = 0xffffffffUL;
+
+static struct resource ks8695_wan_resources[] = {
+ [0] = {
+ .start = KS8695_WAN_VA,
+ .end = KS8695_WAN_VA + 0x00ff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .name = "WAN RX",
+ .start = KS8695_IRQ_WAN_RX_STATUS,
+ .end = KS8695_IRQ_WAN_RX_STATUS,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .name = "WAN TX",
+ .start = KS8695_IRQ_WAN_TX_STATUS,
+ .end = KS8695_IRQ_WAN_TX_STATUS,
+ .flags = IORESOURCE_IRQ,
+ },
+ [3] = {
+ .name = "WAN Link",
+ .start = KS8695_IRQ_WAN_LINK,
+ .end = KS8695_IRQ_WAN_LINK,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device ks8695_wan_device = {
+ .name = "ks8695_ether",
+ .id = 0,
+ .dev = {
+ .dma_mask = ð_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = ks8695_wan_resources,
+ .num_resources = ARRAY_SIZE(ks8695_wan_resources),
+};
+
+
+static struct resource ks8695_lan_resources[] = {
+ [0] = {
+ .start = KS8695_LAN_VA,
+ .end = KS8695_LAN_VA + 0x00ff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .name = "LAN RX",
+ .start = KS8695_IRQ_LAN_RX_STATUS,
+ .end = KS8695_IRQ_LAN_RX_STATUS,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .name = "LAN TX",
+ .start = KS8695_IRQ_LAN_TX_STATUS,
+ .end = KS8695_IRQ_LAN_TX_STATUS,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device ks8695_lan_device = {
+ .name = "ks8695_ether",
+ .id = 1,
+ .dev = {
+ .dma_mask = ð_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = ks8695_lan_resources,
+ .num_resources = ARRAY_SIZE(ks8695_lan_resources),
+};
+
+
+static struct resource ks8695_hpna_resources[] = {
+ [0] = {
+ .start = KS8695_HPNA_VA,
+ .end = KS8695_HPNA_VA + 0x00ff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .name = "HPNA RX",
+ .start = KS8695_IRQ_HPNA_RX_STATUS,
+ .end = KS8695_IRQ_HPNA_RX_STATUS,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .name = "HPNA TX",
+ .start = KS8695_IRQ_HPNA_TX_STATUS,
+ .end = KS8695_IRQ_HPNA_TX_STATUS,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device ks8695_hpna_device = {
+ .name = "ks8695_ether",
+ .id = 2,
+ .dev = {
+ .dma_mask = ð_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = ks8695_hpna_resources,
+ .num_resources = ARRAY_SIZE(ks8695_hpna_resources),
+};
+
+void __init ks8695_add_device_wan(void)
+{
+ platform_device_register(&ks8695_wan_device);
+}
+
+void __init ks8695_add_device_lan(void)
+{
+ platform_device_register(&ks8695_lan_device);
+}
+
+void __init ks8696_add_device_hpna(void)
+{
+ platform_device_register(&ks8695_hpna_device);
+}
+#else
+void __init ks8695_add_device_wan(void) {}
+void __init ks8695_add_device_lan(void) {}
+void __init ks8696_add_device_hpna(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ * Watchdog
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_KS8695_WATCHDOG) || defined(CONFIG_KS8695_WATCHDOG_MODULE)
+static struct platform_device ks8695_wdt_device = {
+ .name = "ks8695_wdt",
+ .id = -1,
+ .num_resources = 0,
+};
+
+static void __init ks8695_add_device_watchdog(void)
+{
+ platform_device_register(&ks8695_wdt_device);
+}
+#else
+static void __init ks8695_add_device_watchdog(void) {}
+#endif
+
+
+/* -------------------------------------------------------------------- */
+
+/*
+ * These devices are always present and don't need any board-specific
+ * setup.
+ */
+static int __init ks8695_add_standard_devices(void)
+{
+ ks8695_add_device_watchdog();
+ return 0;
+}
+
+arch_initcall(ks8695_add_standard_devices);
--- /dev/null
+/*
+ * arch/arm/mach-ks8695/generic.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+*/
+
+extern __init void ks8695_map_io(void);
+extern __init void ks8695_init_irq(void);
+extern struct sys_timer ks8695_timer;
--- /dev/null
+/*
+ * arch/arm/mach-ks8695/irq.c
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/ptrace.h>
+#include <linux/sysdev.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#include <asm/mach/irq.h>
+
+#include <asm/arch/regs-irq.h>
+#include <asm/arch/regs-gpio.h>
+
+static void ks8695_irq_mask(unsigned int irqno)
+{
+ unsigned long inten;
+
+ inten = __raw_readl(KS8695_IRQ_VA + KS8695_INTEN);
+ inten &= ~(1 << irqno);
+
+ __raw_writel(inten, KS8695_IRQ_VA + KS8695_INTEN);
+}
+
+static void ks8695_irq_unmask(unsigned int irqno)
+{
+ unsigned long inten;
+
+ inten = __raw_readl(KS8695_IRQ_VA + KS8695_INTEN);
+ inten |= (1 << irqno);
+
+ __raw_writel(inten, KS8695_IRQ_VA + KS8695_INTEN);
+}
+
+static void ks8695_irq_ack(unsigned int irqno)
+{
+ __raw_writel((1 << irqno), KS8695_IRQ_VA + KS8695_INTST);
+}
+
+
+static struct irq_chip ks8695_irq_level_chip;
+static struct irq_chip ks8695_irq_edge_chip;
+
+
+static int ks8695_irq_set_type(unsigned int irqno, unsigned int type)
+{
+ unsigned long ctrl, mode;
+ unsigned short level_triggered = 0;
+
+ ctrl = __raw_readl(KS8695_GPIO_VA + KS8695_IOPC);
+
+ switch (type) {
+ case IRQT_HIGH:
+ mode = IOPC_TM_HIGH;
+ level_triggered = 1;
+ break;
+ case IRQT_LOW:
+ mode = IOPC_TM_LOW;
+ level_triggered = 1;
+ break;
+ case IRQT_RISING:
+ mode = IOPC_TM_RISING;
+ break;
+ case IRQT_FALLING:
+ mode = IOPC_TM_FALLING;
+ break;
+ case IRQT_BOTHEDGE:
+ mode = IOPC_TM_EDGE;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (irqno) {
+ case KS8695_IRQ_EXTERN0:
+ ctrl &= ~IOPC_IOEINT0TM;
+ ctrl |= IOPC_IOEINT0_MODE(mode);
+ break;
+ case KS8695_IRQ_EXTERN1:
+ ctrl &= ~IOPC_IOEINT1TM;
+ ctrl |= IOPC_IOEINT1_MODE(mode);
+ break;
+ case KS8695_IRQ_EXTERN2:
+ ctrl &= ~IOPC_IOEINT2TM;
+ ctrl |= IOPC_IOEINT2_MODE(mode);
+ break;
+ case KS8695_IRQ_EXTERN3:
+ ctrl &= ~IOPC_IOEINT3TM;
+ ctrl |= IOPC_IOEINT3_MODE(mode);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (level_triggered) {
+ set_irq_chip(irqno, &ks8695_irq_level_chip);
+ set_irq_handler(irqno, handle_level_irq);
+ }
+ else {
+ set_irq_chip(irqno, &ks8695_irq_edge_chip);
+ set_irq_handler(irqno, handle_edge_irq);
+ }
+
+ __raw_writel(ctrl, KS8695_GPIO_VA + KS8695_IOPC);
+ return 0;
+}
+
+static struct irq_chip ks8695_irq_level_chip = {
+ .ack = ks8695_irq_mask,
+ .mask = ks8695_irq_mask,
+ .unmask = ks8695_irq_unmask,
+ .set_type = ks8695_irq_set_type,
+};
+
+static struct irq_chip ks8695_irq_edge_chip = {
+ .ack = ks8695_irq_ack,
+ .mask = ks8695_irq_mask,
+ .unmask = ks8695_irq_unmask,
+ .set_type = ks8695_irq_set_type,
+};
+
+void __init ks8695_init_irq(void)
+{
+ unsigned int irq;
+
+ /* Disable all interrupts initially */
+ __raw_writel(0, KS8695_IRQ_VA + KS8695_INTMC);
+ __raw_writel(0, KS8695_IRQ_VA + KS8695_INTEN);
+
+ for (irq = 0; irq < NR_IRQS; irq++) {
+ switch (irq) {
+ /* Level-triggered interrupts */
+ case KS8695_IRQ_BUS_ERROR:
+ case KS8695_IRQ_UART_MODEM_STATUS:
+ case KS8695_IRQ_UART_LINE_STATUS:
+ case KS8695_IRQ_UART_RX:
+ case KS8695_IRQ_COMM_TX:
+ case KS8695_IRQ_COMM_RX:
+ set_irq_chip(irq, &ks8695_irq_level_chip);
+ set_irq_handler(irq, handle_level_irq);
+ break;
+
+ /* Edge-triggered interrupts */
+ default:
+ ks8695_irq_ack(irq); /* clear pending bit */
+ set_irq_chip(irq, &ks8695_irq_edge_chip);
+ set_irq_handler(irq, handle_edge_irq);
+ }
+
+ set_irq_flags(irq, IRQF_VALID);
+ }
+}
--- /dev/null
+/*
+ * arch/arm/mach-ks8695/time.c
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+
+#include <asm/io.h>
+#include <asm/mach/time.h>
+
+#include <asm/arch/regs-timer.h>
+#include <asm/arch/regs-irq.h>
+
+#include "generic.h"
+
+/*
+ * Returns number of ms since last clock interrupt. Note that interrupts
+ * will have been disabled by do_gettimeoffset()
+ */
+static unsigned long ks8695_gettimeoffset (void)
+{
+ unsigned long elapsed, tick2, intpending;
+
+ /*
+ * Get the current number of ticks. Note that there is a race
+ * condition between us reading the timer and checking for an
+ * interrupt. We solve this by ensuring that the counter has not
+ * reloaded between our two reads.
+ */
+ elapsed = __raw_readl(KS8695_TMR_VA + KS8695_T1TC) + __raw_readl(KS8695_TMR_VA + KS8695_T1PD);
+ do {
+ tick2 = elapsed;
+ intpending = __raw_readl(KS8695_IRQ_VA + KS8695_INTST) & (1 << KS8695_IRQ_TIMER1);
+ elapsed = __raw_readl(KS8695_TMR_VA + KS8695_T1TC) + __raw_readl(KS8695_TMR_VA + KS8695_T1PD);
+ } while (elapsed > tick2);
+
+ /* Convert to number of ticks expired (not remaining) */
+ elapsed = (CLOCK_TICK_RATE / HZ) - elapsed;
+
+ /* Is interrupt pending? If so, then timer has been reloaded already. */
+ if (intpending)
+ elapsed += (CLOCK_TICK_RATE / HZ);
+
+ /* Convert ticks to usecs */
+ return (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH;
+}
+
+/*
+ * IRQ handler for the timer.
+ */
+static irqreturn_t ks8695_timer_interrupt(int irq, void *dev_id)
+{
+ write_seqlock(&xtime_lock);
+ timer_tick();
+ write_sequnlock(&xtime_lock);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction ks8695_timer_irq = {
+ .name = "ks8695_tick",
+ .flags = IRQF_DISABLED | IRQF_TIMER,
+ .handler = ks8695_timer_interrupt,
+};
+
+static void ks8695_timer_setup(void)
+{
+ unsigned long tmout = CLOCK_TICK_RATE / HZ;
+ unsigned long tmcon;
+
+ /* disable timer1 */
+ tmcon = __raw_readl(KS8695_TMR_VA + KS8695_TMCON);
+ __raw_writel(tmcon & ~TMCON_T1EN, KS8695_TMR_VA + KS8695_TMCON);
+
+ __raw_writel(tmout / 2, KS8695_TMR_VA + KS8695_T1TC);
+ __raw_writel(tmout / 2, KS8695_TMR_VA + KS8695_T1PD);
+
+ /* re-enable timer1 */
+ __raw_writel(tmcon | TMCON_T1EN, KS8695_TMR_VA + KS8695_TMCON);
+}
+
+static void __init ks8695_timer_init (void)
+{
+ ks8695_timer_setup();
+
+ /* Enable timer interrupts */
+ setup_irq(KS8695_IRQ_TIMER1, &ks8695_timer_irq);
+}
+
+struct sys_timer ks8695_timer = {
+ .init = ks8695_timer_init,
+ .offset = ks8695_gettimeoffset,
+ .resume = ks8695_timer_setup,
+};
# ARM922T
config CPU_ARM922T
bool "Support ARM922T processor" if ARCH_INTEGRATOR
- depends on ARCH_LH7A40X || ARCH_INTEGRATOR
- default y if ARCH_LH7A40X
+ depends on ARCH_LH7A40X || ARCH_INTEGRATOR || ARCH_KS8695
+ default y if ARCH_LH7A40X || ARCH_KS8695
select CPU_32v4T
select CPU_ABRT_EV4T
select CPU_CACHE_V4WT
help
The ARM922T is a version of the ARM920T, but with smaller
instruction and data caches. It is used in Altera's
- Excalibur XA device family.
+ Excalibur XA device family and Micrel's KS8695 Centaur.
Say Y if you want support for the ARM922T processor.
Otherwise, say N.
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/debug-macro.S
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - Debug macros
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <asm/hardware.h>
+#include <asm/arch/regs-uart.h>
+
+ .macro addruart, rx
+ mrc p15, 0, \rx, c1, c0
+ tst \rx, #1 @ MMU enabled?
+ ldreq \rx, =KS8695_UART_PA @ physical base address
+ ldrne \rx, =KS8695_UART_VA @ virtual base address
+ .endm
+
+ .macro senduart, rd, rx
+ str \rd, [\rx, #KS8695_URTH] @ Write to Transmit Holding Register
+ .endm
+
+ .macro busyuart, rd, rx
+1001: ldr \rd, [\rx, #KS8695_URLS] @ Read Line Status Register
+ tst \rd, #URLS_URTE @ Holding & Shift registers empty?
+ beq 1001b
+ .endm
+
+ .macro waituart, rd, rx
+1001: ldr \rd, [\rx, #KS8695_URLS] @ Read Line Status Register
+ tst \rd, #URLS_URTHRE @ Holding Register empty?
+ beq 1001b
+ .endm
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/devices.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_DEVICES_H
+#define __ASM_ARCH_DEVICES_H
+
+#include <linux/pci.h>
+
+ /* Ethernet */
+extern void __init ks8695_add_device_wan(void);
+extern void __init ks8695_add_device_lan(void);
+extern void __init ks8695_add_device_hpna(void);
+
+ /* PCI */
+#define KS8695_MODE_PCI 0
+#define KS8695_MODE_MINIPCI 1
+#define KS8695_MODE_CARDBUS 2
+
+struct ks8695_pci_cfg {
+ short mode;
+ int (*map_irq)(struct pci_dev *, u8, u8);
+};
+extern __init void ks8695_init_pci(struct ks8695_pci_cfg *);
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/dma.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/entry-macro.S
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * Low-level IRQ helper macros for KS8695
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+*/
+
+#include <asm/hardware.h>
+#include <asm/arch/regs-irq.h>
+
+ .macro disable_fiq
+ .endm
+
+ .macro get_irqnr_preamble, base, tmp
+ ldr \base, =KS8695_IRQ_VA @ Base address of interrupt controller
+ .endm
+
+ .macro arch_ret_to_user, tmp1, tmp2
+ .endm
+
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+ ldr \irqstat, [\base, #KS8695_INTMS] @ Mask Status register
+
+ teq \irqstat, #0
+ beq 1001f
+
+ mov \irqnr, #0
+
+ tst \irqstat, #0xff
+ moveq \irqstat, \irqstat, lsr #8
+ addeq \irqnr, \irqnr, #8
+ tsteq \irqstat, #0xff
+ moveq \irqstat, \irqstat, lsr #8
+ addeq \irqnr, \irqnr, #8
+ tsteq \irqstat, #0xff
+ moveq \irqstat, \irqstat, lsr #8
+ addeq \irqnr, \irqnr, #8
+ tst \irqstat, #0x0f
+ moveq \irqstat, \irqstat, lsr #4
+ addeq \irqnr, \irqnr, #4
+ tst \irqstat, #0x03
+ moveq \irqstat, \irqstat, lsr #2
+ addeq \irqnr, \irqnr, #2
+ tst \irqstat, #0x01
+ addeqs \irqnr, \irqnr, #1
+1001:
+ .endm
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/hardware.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - Memory Map definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+#include <asm/sizes.h>
+
+/*
+ * Physical RAM address.
+ */
+#define KS8695_SDRAM_PA 0x00000000
+
+
+/*
+ * We map an entire MiB with the System Configuration Registers in even
+ * though only 64KiB is needed. This makes it easier for use with the
+ * head debug code as the initial MMU setup only deals in L1 sections.
+ */
+#define KS8695_IO_PA 0x03F00000
+#define KS8695_IO_VA 0xF0000000
+#define KS8695_IO_SIZE SZ_1M
+
+#define KS8695_PCIMEM_PA 0x60000000
+#define KS8695_PCIMEM_SIZE SZ_512M
+
+#define KS8695_PCIIO_PA 0x80000000
+#define KS8695_PCIIO_SIZE SZ_64K
+
+
+/*
+ * PCI support
+ */
+#define pcibios_assign_all_busses() 1
+
+#define PCIBIOS_MIN_IO 0
+#define PCIBIOS_MIN_MEM 0
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/io.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_IO_H
+#define __ASM_ARCH_IO_H
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+#define __io(a) ((void __iomem *)(a))
+#define __mem_pci(a) (a)
+
+#endif
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-ks8695/irqs.h
+ *
+ * Copyright (C) 2006 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_IRQS_H
+#define __ASM_ARCH_IRQS_H
+
+
+#define NR_IRQS 32
+
+/*
+ * IRQ definitions
+ */
+#define KS8695_IRQ_COMM_RX 0
+#define KS8695_IRQ_COMM_TX 1
+#define KS8695_IRQ_EXTERN0 2
+#define KS8695_IRQ_EXTERN1 3
+#define KS8695_IRQ_EXTERN2 4
+#define KS8695_IRQ_EXTERN3 5
+#define KS8695_IRQ_TIMER0 6
+#define KS8695_IRQ_TIMER1 7
+#define KS8695_IRQ_UART_TX 8
+#define KS8695_IRQ_UART_RX 9
+#define KS8695_IRQ_UART_LINE_STATUS 10
+#define KS8695_IRQ_UART_MODEM_STATUS 11
+#define KS8695_IRQ_LAN_RX_STOP 12
+#define KS8695_IRQ_LAN_TX_STOP 13
+#define KS8695_IRQ_LAN_RX_BUF 14
+#define KS8695_IRQ_LAN_TX_BUF 15
+#define KS8695_IRQ_LAN_RX_STATUS 16
+#define KS8695_IRQ_LAN_TX_STATUS 17
+#define KS8695_IRQ_HPNA_RX_STOP 18
+#define KS8695_IRQ_HPNA_TX_STOP 19
+#define KS8695_IRQ_HPNA_RX_BUF 20
+#define KS8695_IRQ_HPNA_TX_BUF 21
+#define KS8695_IRQ_HPNA_RX_STATUS 22
+#define KS8695_IRQ_HPNA_TX_STATUS 23
+#define KS8695_IRQ_BUS_ERROR 24
+#define KS8695_IRQ_WAN_RX_STOP 25
+#define KS8695_IRQ_WAN_TX_STOP 26
+#define KS8695_IRQ_WAN_RX_BUF 27
+#define KS8695_IRQ_WAN_TX_BUF 28
+#define KS8695_IRQ_WAN_RX_STATUS 29
+#define KS8695_IRQ_WAN_TX_STATUS 30
+#define KS8695_IRQ_WAN_LINK 31
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/memory.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * KS8695 Memory definitions
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+#include <asm/hardware.h>
+
+/*
+ * Physical SRAM offset.
+ */
+#define PHYS_OFFSET KS8695_SDRAM_PA
+
+#ifndef __ASSEMBLY__
+
+#ifdef CONFIG_PCI
+
+/* PCI mappings */
+#define __virt_to_bus(x) ((x) - PAGE_OFFSET + KS8695_PCIMEM_PA)
+#define __bus_to_virt(x) ((x) - KS8695_PCIMEM_PA + PAGE_OFFSET)
+
+/* Platform-bus mapping */
+extern struct bus_type platform_bus_type;
+#define is_lbus_device(dev) (dev && dev->bus == &platform_bus_type)
+#define __arch_dma_to_virt(dev, x) ({ is_lbus_device(dev) ? \
+ __phys_to_virt(x) : __bus_to_virt(x); })
+#define __arch_virt_to_dma(dev, x) ({ is_lbus_device(dev) ? \
+ (dma_addr_t)__virt_to_phys(x) : (dma_addr_t)__virt_to_bus(x); })
+#define __arch_page_to_dma(dev, x) __arch_virt_to_dma(dev, page_address(x))
+
+#else
+
+#define __virt_to_bus(x) __virt_to_phys(x)
+#define __bus_to_virt(x) __phys_to_virt(x)
+
+#endif
+
+#endif
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-gpio.h
+ *
+ * Copyright (C) 2007 Andrew Victor
+ *
+ * KS8695 - GPIO control registers and bit definitions.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_GPIO_H
+#define KS8695_GPIO_H
+
+#define KS8695_GPIO_OFFSET (0xF0000 + 0xE600)
+#define KS8695_GPIO_VA (KS8695_IO_VA + KS8695_GPIO_OFFSET)
+#define KS8695_GPIO_PA (KS8695_IO_PA + KS8695_GPIO_OFFSET)
+
+
+#define KS8695_IOPM (0x00) /* I/O Port Mode Register */
+#define KS8695_IOPC (0x04) /* I/O Port Control Register */
+#define KS8695_IOPD (0x08) /* I/O Port Data Register */
+
+
+/* Port Mode Register */
+#define IOPM_(x) (1 << (x)) /* Mode for GPIO Pin x */
+
+/* Port Control Register */
+#define IOPC_IOTIM1EN (1 << 17) /* GPIO Pin for Timer1 Enable */
+#define IOPC_IOTIM0EN (1 << 16) /* GPIO Pin for Timer0 Enable */
+#define IOPC_IOEINT3EN (1 << 15) /* GPIO Pin for External/Soft Interrupt 3 Enable */
+#define IOPC_IOEINT3TM (7 << 12) /* GPIO Pin for External/Soft Interrupt 3 Trigger Mode */
+#define IOPC_IOEINT3_MODE(x) ((x) << 12)
+#define IOPC_IOEINT2EN (1 << 11) /* GPIO Pin for External/Soft Interrupt 2 Enable */
+#define IOPC_IOEINT2TM (7 << 8) /* GPIO Pin for External/Soft Interrupt 2 Trigger Mode */
+#define IOPC_IOEINT2_MODE(x) ((x) << 8)
+#define IOPC_IOEINT1EN (1 << 7) /* GPIO Pin for External/Soft Interrupt 1 Enable */
+#define IOPC_IOEINT1TM (7 << 4) /* GPIO Pin for External/Soft Interrupt 1 Trigger Mode */
+#define IOPC_IOEINT1_MODE(x) ((x) << 4)
+#define IOPC_IOEINT0EN (1 << 3) /* GPIO Pin for External/Soft Interrupt 0 Enable */
+#define IOPC_IOEINT0TM (7 << 0) /* GPIO Pin for External/Soft Interrupt 0 Trigger Mode */
+#define IOPC_IOEINT0_MODE(x) ((x) << 0)
+
+ /* Trigger Modes */
+#define IOPC_TM_LOW (0) /* Level Detection (Active Low) */
+#define IOPC_TM_HIGH (1) /* Level Detection (Active High) */
+#define IOPC_TM_RISING (2) /* Rising Edge Detection */
+#define IOPC_TM_FALLING (4) /* Falling Edge Detection */
+#define IOPC_TM_EDGE (6) /* Both Edge Detection */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-wan.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * KS8695 - HPNA Registers and bit definitions.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_HPNA_H
+#define KS8695_HPNA_H
+
+#define KS8695_HPNA_OFFSET (0xF0000 + 0xA000)
+#define KS8695_HPNA_VA (KS8695_IO_VA + KS8695_HPNA_OFFSET)
+#define KS8695_HPNA_PA (KS8695_IO_PA + KS8695_HPNA_OFFSET)
+
+
+/*
+ * HPNA registers
+ */
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-irq.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - IRQ registers and bit definitions
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_IRQ_H
+#define KS8695_IRQ_H
+
+#define KS8695_IRQ_OFFSET (0xF0000 + 0xE200)
+#define KS8695_IRQ_VA (KS8695_IO_VA + KS8695_IRQ_OFFSET)
+#define KS8695_IRQ_PA (KS8695_IO_PA + KS8695_IRQ_OFFSET)
+
+
+/*
+ * Interrupt Controller registers
+ */
+#define KS8695_INTMC (0x00) /* Mode Control Register */
+#define KS8695_INTEN (0x04) /* Interrupt Enable Register */
+#define KS8695_INTST (0x08) /* Interrupt Status Register */
+#define KS8695_INTPW (0x0c) /* Interrupt Priority (WAN MAC) */
+#define KS8695_INTPH (0x10) /* Interrupt Priority (HPNA) [KS8695 only] */
+#define KS8695_INTPL (0x14) /* Interrupt Priority (LAN MAC) */
+#define KS8695_INTPT (0x18) /* Interrupt Priority (Timer) */
+#define KS8695_INTPU (0x1c) /* Interrupt Priority (UART) */
+#define KS8695_INTPE (0x20) /* Interrupt Priority (External Interrupt) */
+#define KS8695_INTPC (0x24) /* Interrupt Priority (Communications Channel) */
+#define KS8695_INTPBE (0x28) /* Interrupt Priority (Bus Error Response) */
+#define KS8695_INTMS (0x2c) /* Interrupt Mask Status Register */
+#define KS8695_INTHPF (0x30) /* Interrupt Pending Highest Priority (FIQ) */
+#define KS8695_INTHPI (0x34) /* Interrupt Pending Highest Priority (IRQ) */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-lan.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * KS8695 - LAN Registers and bit definitions.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_LAN_H
+#define KS8695_LAN_H
+
+#define KS8695_LAN_OFFSET (0xF0000 + 0x8000)
+#define KS8695_LAN_VA (KS8695_IO_VA + KS8695_LAN_OFFSET)
+#define KS8695_LAN_PA (KS8695_IO_PA + KS8695_LAN_OFFSET)
+
+
+/*
+ * LAN registers
+ */
+#define KS8695_LMDTXC (0x00) /* DMA Transmit Control */
+#define KS8695_LMDRXC (0x04) /* DMA Receive Control */
+#define KS8695_LMDTSC (0x08) /* DMA Transmit Start Command */
+#define KS8695_LMDRSC (0x0c) /* DMA Receive Start Command */
+#define KS8695_LTDLB (0x10) /* Transmit Descriptor List Base Address */
+#define KS8695_LRDLB (0x14) /* Receive Descriptor List Base Address */
+#define KS8695_LMAL (0x18) /* MAC Station Address Low */
+#define KS8695_LMAH (0x1c) /* MAC Station Address High */
+#define KS8695_LMAAL_(n) (0x80 + ((n)*8)) /* MAC Additional Station Address (0..15) Low */
+#define KS8695_LMAAH_(n) (0x84 + ((n)*8)) /* MAC Additional Station Address (0..15) High */
+
+
+/* DMA Transmit Control Register */
+#define LMDTXC_LMTRST (1 << 31) /* Soft Reset */
+#define LMDTXC_LMTBS (0x3f << 24) /* Transmit Burst Size */
+#define LMDTXC_LMTUCG (1 << 18) /* Transmit UDP Checksum Generate */
+#define LMDTXC_LMTTCG (1 << 17) /* Transmit TCP Checksum Generate */
+#define LMDTXC_LMTICG (1 << 16) /* Transmit IP Checksum Generate */
+#define LMDTXC_LMTFCE (1 << 9) /* Transmit Flow Control Enable */
+#define LMDTXC_LMTLB (1 << 8) /* Loopback mode */
+#define LMDTXC_LMTEP (1 << 2) /* Transmit Enable Padding */
+#define LMDTXC_LMTAC (1 << 1) /* Transmit Add CRC */
+#define LMDTXC_LMTE (1 << 0) /* TX Enable */
+
+/* DMA Receive Control Register */
+#define LMDRXC_LMRBS (0x3f << 24) /* Receive Burst Size */
+#define LMDRXC_LMRUCC (1 << 18) /* Receive UDP Checksum check */
+#define LMDRXC_LMRTCG (1 << 17) /* Receive TCP Checksum check */
+#define LMDRXC_LMRICG (1 << 16) /* Receive IP Checksum check */
+#define LMDRXC_LMRFCE (1 << 9) /* Receive Flow Control Enable */
+#define LMDRXC_LMRB (1 << 6) /* Receive Broadcast */
+#define LMDRXC_LMRM (1 << 5) /* Receive Multicast */
+#define LMDRXC_LMRU (1 << 4) /* Receive Unicast */
+#define LMDRXC_LMRERR (1 << 3) /* Receive Error Frame */
+#define LMDRXC_LMRA (1 << 2) /* Receive All */
+#define LMDRXC_LMRE (1 << 1) /* RX Enable */
+
+/* Additional Station Address High */
+#define LMAAH_E (1 << 31) /* Address Enabled */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-mem.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * KS8695 - Memory Controller registers and bit definitions
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_MEM_H
+#define KS8695_MEM_H
+
+#define KS8695_MEM_OFFSET (0xF0000 + 0x4000)
+#define KS8695_MEM_VA (KS8695_IO_VA + KS8695_MEM_OFFSET)
+#define KS8695_MEM_PA (KS8695_IO_PA + KS8695_MEM_OFFSET)
+
+
+/*
+ * Memory Controller Registers
+ */
+#define KS8695_EXTACON0 (0x00) /* External I/O 0 Access Control */
+#define KS8695_EXTACON1 (0x04) /* External I/O 1 Access Control */
+#define KS8695_EXTACON2 (0x08) /* External I/O 2 Access Control */
+#define KS8695_ROMCON0 (0x10) /* ROM/SRAM/Flash 1 Control Register */
+#define KS8695_ROMCON1 (0x14) /* ROM/SRAM/Flash 2 Control Register */
+#define KS8695_ERGCON (0x20) /* External I/O and ROM/SRAM/Flash General Register */
+#define KS8695_SDCON0 (0x30) /* SDRAM Control Register 0 */
+#define KS8695_SDCON1 (0x34) /* SDRAM Control Register 1 */
+#define KS8695_SDGCON (0x38) /* SDRAM General Control */
+#define KS8695_SDBCON (0x3c) /* SDRAM Buffer Control */
+#define KS8695_REFTIM (0x40) /* SDRAM Refresh Timer */
+
+
+/* External I/O Access Control Registers */
+#define EXTACON_EBNPTR (0x3ff << 22) /* Last Address Pointer */
+#define EXTACON_EBBPTR (0x3ff << 12) /* Base Pointer */
+#define EXTACON_EBTACT (7 << 9) /* Write Enable/Output Enable Active Time */
+#define EXTACON_EBTCOH (7 << 6) /* Chip Select Hold Time */
+#define EXTACON_EBTACS (7 << 3) /* Address Setup Time before ECSN */
+#define EXTACON_EBTCOS (7 << 0) /* Chip Select Time before OEN */
+
+/* ROM/SRAM/Flash Control Register */
+#define ROMCON_RBNPTR (0x3ff << 22) /* Next Pointer */
+#define ROMCON_RBBPTR (0x3ff << 12) /* Base Pointer */
+#define ROMCON_RBTACC (7 << 4) /* Access Cycle Time */
+#define ROMCON_RBTPA (3 << 2) /* Page Address Access Time */
+#define ROMCON_PMC (3 << 0) /* Page Mode Configuration */
+#define PMC_NORMAL (0 << 0)
+#define PMC_4WORD (1 << 0)
+#define PMC_8WORD (2 << 0)
+#define PMC_16WORD (3 << 0)
+
+/* External I/O and ROM/SRAM/Flash General Register */
+#define ERGCON_TMULT (3 << 28) /* Time Multiplier */
+#define ERGCON_DSX2 (3 << 20) /* Data Width (External I/O Bank 2) */
+#define ERGCON_DSX1 (3 << 18) /* Data Width (External I/O Bank 1) */
+#define ERGCON_DSX0 (3 << 16) /* Data Width (External I/O Bank 0) */
+#define ERGCON_DSR1 (3 << 2) /* Data Width (ROM/SRAM/Flash Bank 1) */
+#define ERGCON_DSR0 (3 << 0) /* Data Width (ROM/SRAM/Flash Bank 0) */
+
+/* SDRAM Control Register */
+#define SDCON_DBNPTR (0x3ff << 22) /* Last Address Pointer */
+#define SDCON_DBBPTR (0x3ff << 12) /* Base Pointer */
+#define SDCON_DBCAB (3 << 8) /* Column Address Bits */
+#define SDCON_DBBNUM (1 << 3) /* Number of Banks */
+#define SDCON_DBDBW (3 << 1) /* Data Bus Width */
+
+/* SDRAM General Control Register */
+#define SDGCON_SDTRC (3 << 2) /* RAS to CAS latency */
+#define SDGCON_SDCAS (3 << 0) /* CAS latency */
+
+/* SDRAM Buffer Control Register */
+#define SDBCON_SDESTA (1 << 31) /* SDRAM Engine Status */
+#define SDBCON_RBUFBDIS (1 << 24) /* Read Buffer Burst Enable */
+#define SDBCON_WFIFOEN (1 << 23) /* Write FIFO Enable */
+#define SDBCON_RBUFEN (1 << 22) /* Read Buffer Enable */
+#define SDBCON_FLUSHWFIFO (1 << 21) /* Flush Write FIFO */
+#define SDBCON_RBUFINV (1 << 20) /* Read Buffer Invalidate */
+#define SDBCON_SDINI (3 << 16) /* SDRAM Initialization Control */
+#define SDBCON_SDMODE (0x3fff << 0) /* SDRAM Mode Register Value Program */
+
+/* SDRAM Refresh Timer Register */
+#define REFTIM_REFTIM (0xffff << 0) /* Refresh Timer Value */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-misc.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * KS8695 - Miscellaneous Registers
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_MISC_H
+#define KS8695_MISC_H
+
+#define KS8695_MISC_OFFSET (0xF0000 + 0xEA00)
+#define KS8695_MISC_VA (KS8695_IO_VA + KS8695_MISC_OFFSET)
+#define KS8695_MISC_PA (KS8695_IO_PA + KS8695_MISC_OFFSET)
+
+
+/*
+ * Miscellaneous registers
+ */
+#define KS8695_DID (0x00) /* Device ID */
+#define KS8695_RID (0x04) /* Revision ID */
+#define KS8695_HMC (0x08) /* HPNA Miscellaneous Control [KS8695 only] */
+#define KS8695_WMC (0x0c) /* WAN Miscellaneous Control */
+#define KS8695_WPPM (0x10) /* WAN PHY Power Management */
+#define KS8695_PPS (0x1c) /* PHY PowerSave */
+
+/* Device ID Register */
+#define DID_ID (0xffff << 0) /* Device ID */
+
+/* Revision ID Register */
+#define RID_SUBID (0xf << 4) /* Sub-Device ID */
+#define RID_REVISION (0xf << 0) /* Revision ID */
+
+/* HPNA Miscellaneous Control Register */
+#define HMC_HSS (1 << 1) /* Speed */
+#define HMC_HDS (1 << 0) /* Duplex */
+
+/* WAN Miscellaneous Control Register */
+#define WMC_WANC (1 << 30) /* Auto-negotiation complete */
+#define WMC_WANR (1 << 29) /* Auto-negotiation restart */
+#define WMC_WANAP (1 << 28) /* Advertise Pause */
+#define WMC_WANA100F (1 << 27) /* Advertise 100 FDX */
+#define WMC_WANA100H (1 << 26) /* Advertise 100 HDX */
+#define WMC_WANA10F (1 << 25) /* Advertise 10 FDX */
+#define WMC_WANA10H (1 << 24) /* Advertise 10 HDX */
+#define WMC_WLS (1 << 23) /* Link status */
+#define WMC_WDS (1 << 22) /* Duplex status */
+#define WMC_WSS (1 << 21) /* Speed status */
+#define WMC_WLPP (1 << 20) /* Link Partner Pause */
+#define WMC_WLP100F (1 << 19) /* Link Partner 100 FDX */
+#define WMC_WLP100H (1 << 18) /* Link Partner 100 HDX */
+#define WMC_WLP10F (1 << 17) /* Link Partner 10 FDX */
+#define WMC_WLP10H (1 << 16) /* Link Partner 10 HDX */
+#define WMC_WAND (1 << 15) /* Auto-negotiation disable */
+#define WMC_WANF100 (1 << 14) /* Force 100 */
+#define WMC_WANFF (1 << 13) /* Force FDX */
+#define WMC_WLED1S (7 << 4) /* LED1 Select */
+#define WLED1S_SPEED (0 << 4)
+#define WLED1S_LINK (1 << 4)
+#define WLED1S_DUPLEX (2 << 4)
+#define WLED1S_COLLISION (3 << 4)
+#define WLED1S_ACTIVITY (4 << 4)
+#define WLED1S_FDX_COLLISION (5 << 4)
+#define WLED1S_LINK_ACTIVITY (6 << 4)
+#define WMC_WLED0S (7 << 0) /* LED0 Select */
+#define WLED0S_SPEED (0 << 0)
+#define WLED0S_LINK (1 << 0)
+#define WLED0S_DUPLEX (2 << 0)
+#define WLED0S_COLLISION (3 << 0)
+#define WLED0S_ACTIVITY (4 << 0)
+#define WLED0S_FDX_COLLISION (5 << 0)
+#define WLED0S_LINK_ACTIVITY (6 << 0)
+
+/* WAN PHY Power Management Register */
+#define WPPM_WLPBK (1 << 14) /* Local Loopback */
+#define WPPM_WRLPKB (1 << 13) /* Remove Loopback */
+#define WPPM_WPI (1 << 12) /* PHY isolate */
+#define WPPM_WFL (1 << 10) /* Force link */
+#define WPPM_MDIXS (1 << 9) /* MDIX Status */
+#define WPPM_FEF (1 << 8) /* Far End Fault */
+#define WPPM_AMDIXP (1 << 7) /* Auto MDIX Parameter */
+#define WPPM_TXDIS (1 << 6) /* Disable transmitter */
+#define WPPM_DFEF (1 << 5) /* Disable Far End Fault */
+#define WPPM_PD (1 << 4) /* Power Down */
+#define WPPM_DMDX (1 << 3) /* Disable Auto MDI/MDIX */
+#define WPPM_FMDX (1 << 2) /* Force MDIX */
+#define WPPM_LPBK (1 << 1) /* MAX Loopback */
+
+/* PHY Power Save Register */
+#define PPS_PPSM (1 << 0) /* PHY Power Save Mode */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-pci.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - PCI bridge registers and bit definitions.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#define KS8695_PCI_OFFSET (0xF0000 + 0x2000)
+#define KS8695_PCI_VA (KS8695_IO_VA + KS8695_PCI_OFFSET)
+#define KS8695_PCI_PA (KS8695_IO_PA + KS8695_PCI_OFFSET)
+
+
+#define KS8695_CRCFID (0x000) /* Configuration: Identification */
+#define KS8695_CRCFCS (0x004) /* Configuration: Command and Status */
+#define KS8695_CRCFRV (0x008) /* Configuration: Revision */
+#define KS8695_CRCFLT (0x00C) /* Configuration: Latency Timer */
+#define KS8695_CRCBMA (0x010) /* Configuration: Base Memory Address */
+#define KS8695_CRCSID (0x02C) /* Configuration: Subsystem ID */
+#define KS8695_CRCFIT (0x03C) /* Configuration: Interrupt */
+#define KS8695_PBCA (0x100) /* Bridge Configuration Address */
+#define KS8695_PBCD (0x104) /* Bridge Configuration Data */
+#define KS8695_PBM (0x200) /* Bridge Mode */
+#define KS8695_PBCS (0x204) /* Bridge Control and Status */
+#define KS8695_PMBA (0x208) /* Bridge Memory Base Address */
+#define KS8695_PMBAC (0x20C) /* Bridge Memory Base Address Control */
+#define KS8695_PMBAM (0x210) /* Bridge Memory Base Address Mask */
+#define KS8695_PMBAT (0x214) /* Bridge Memory Base Address Translation */
+#define KS8695_PIOBA (0x218) /* Bridge I/O Base Address */
+#define KS8695_PIOBAC (0x21C) /* Bridge I/O Base Address Control */
+#define KS8695_PIOBAM (0x220) /* Bridge I/O Base Address Mask */
+#define KS8695_PIOBAT (0x224) /* Bridge I/O Base Address Translation */
+
+
+/* Configuration: Identification */
+
+/* Configuration: Command and Status */
+
+/* Configuration: Revision */
+
+
+
+#define CFRV_GUEST (1 << 23)
+
+#define PBCA_TYPE1 (1)
+#define PBCA_ENABLE (1 << 31)
+
+
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-switch.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * KS8695 - Switch Registers and bit definitions.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_SWITCH_H
+#define KS8695_SWITCH_H
+
+#define KS8695_SWITCH_OFFSET (0xF0000 + 0xe800)
+#define KS8695_SWITCH_VA (KS8695_IO_VA + KS8695_SWITCH_OFFSET)
+#define KS8695_SWITCH_PA (KS8695_IO_PA + KS8695_SWITCH_OFFSET)
+
+
+/*
+ * Switch registers
+ */
+#define KS8695_SEC0 (0x00) /* Switch Engine Control 0 */
+#define KS8695_SEC1 (0x04) /* Switch Engine Control 1 */
+#define KS8695_SEC2 (0x08) /* Switch Engine Control 2 */
+
+#define KS8695_P(x)_C(z) (0xc0 + (((x)-1)*3 + ((z)-1))*4) /* Port Configuration Registers */
+
+#define KS8695_SEP12AN (0x48) /* Port 1 & 2 Auto-Negotiation */
+#define KS8695_SEP34AN (0x4c) /* Port 3 & 4 Auto-Negotiation */
+#define KS8695_SEIAC (0x50) /* Indirect Access Control */
+#define KS8695_SEIADH2 (0x54) /* Indirect Access Data High 2 */
+#define KS8695_SEIADH1 (0x58) /* Indirect Access Data High 1 */
+#define KS8695_SEIADL (0x5c) /* Indirect Access Data Low */
+#define KS8695_SEAFC (0x60) /* Advance Feature Control */
+#define KS8695_SEDSCPH (0x64) /* TOS Priority High */
+#define KS8695_SEDSCPL (0x68) /* TOS Priority Low */
+#define KS8695_SEMAH (0x6c) /* Switch Engine MAC Address High */
+#define KS8695_SEMAL (0x70) /* Switch Engine MAC Address Low */
+#define KS8695_LPPM12 (0x74) /* Port 1 & 2 PHY Power Management */
+#define KS8695_LPPM34 (0x78) /* Port 3 & 4 PHY Power Management */
+
+
+/* Switch Engine Control 0 */
+#define SEC0_LLED1S (7 << 25) /* LED1 Select */
+#define LLED1S_SPEED (0 << 25)
+#define LLED1S_LINK (1 << 25)
+#define LLED1S_DUPLEX (2 << 25)
+#define LLED1S_COLLISION (3 << 25)
+#define LLED1S_ACTIVITY (4 << 25)
+#define LLED1S_FDX_COLLISION (5 << 25)
+#define LLED1S_LINK_ACTIVITY (6 << 25)
+#define SEC0_LLED0S (7 << 22) /* LED0 Select */
+#define LLED0S_SPEED (0 << 22)
+#define LLED0S_LINK (1 << 22)
+#define LLED0S_DUPLEX (2 << 22)
+#define LLED0S_COLLISION (3 << 22)
+#define LLED0S_ACTIVITY (4 << 22)
+#define LLED0S_FDX_COLLISION (5 << 22)
+#define LLED0S_LINK_ACTIVITY (6 << 22)
+#define SEC0_ENABLE (1 << 0) /* Enable Switch */
+
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-sys.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - System control registers and bit definitions
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_SYS_H
+#define KS8695_SYS_H
+
+#define KS8695_SYS_OFFSET (0xF0000 + 0x0000)
+#define KS8695_SYS_VA (KS8695_IO_VA + KS8695_SYS_OFFSET)
+#define KS8695_SYS_PA (KS8695_IO_PA + KS8695_SYS_OFFSET)
+
+
+#define KS8695_SYSCFG (0x00) /* System Configuration Register */
+#define KS8695_CLKCON (0x04) /* System Clock and Bus Control Register */
+
+
+/* System Configuration Register */
+#define SYSCFG_SPRBP (0x3ff << 16) /* Register Bank Base Pointer */
+
+/* System Clock and Bus Control Register */
+#define CLKCON_SFMODE (1 << 8) /* System Fast Mode for Simulation */
+#define CLKCON_SCDC (7 << 0) /* System Clock Divider Select */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-timer.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - Timer registers and bit definitions.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_TIMER_H
+#define KS8695_TIMER_H
+
+#define KS8695_TMR_OFFSET (0xF0000 + 0xE400)
+#define KS8695_TMR_VA (KS8695_IO_VA + KS8695_TMR_OFFSET)
+#define KS8695_TMR_PA (KS8695_IO_PA + KS8695_TMR_OFFSET)
+
+
+/*
+ * Timer registers
+ */
+#define KS8695_TMCON (0x00) /* Timer Control Register */
+#define KS8695_T1TC (0x04) /* Timer 1 Timeout Count Register */
+#define KS8695_T0TC (0x08) /* Timer 0 Timeout Count Register */
+#define KS8695_T1PD (0x0C) /* Timer 1 Pulse Count Register */
+#define KS8695_T0PD (0x10) /* Timer 0 Pulse Count Register */
+
+
+/* Timer Control Register */
+#define TMCON_T1EN (1 << 1) /* Timer 1 Enable */
+#define TMCON_T0EN (1 << 0) /* Timer 0 Enable */
+
+/* Timer0 Timeout Counter Register */
+#define T0TC_WATCHDOG (0xff) /* Enable watchdog mode */
+
+
+#endif
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-ks8695/regs-uart.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - UART register and bit definitions.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef KS8695_UART_H
+#define KS8695_UART_H
+
+#define KS8695_UART_OFFSET (0xF0000 + 0xE000)
+#define KS8695_UART_VA (KS8695_IO_VA + KS8695_UART_OFFSET)
+#define KS8695_UART_PA (KS8695_IO_PA + KS8695_UART_OFFSET)
+
+
+/*
+ * UART registers
+ */
+#define KS8695_URRB (0x00) /* Receive Buffer Register */
+#define KS8695_URTH (0x04) /* Transmit Holding Register */
+#define KS8695_URFC (0x08) /* FIFO Control Register */
+#define KS8695_URLC (0x0C) /* Line Control Register */
+#define KS8695_URMC (0x10) /* Modem Control Register */
+#define KS8695_URLS (0x14) /* Line Status Register */
+#define KS8695_URMS (0x18) /* Modem Status Register */
+#define KS8695_URBD (0x1C) /* Baud Rate Divisor Register */
+#define KS8695_USR (0x20) /* Status Register */
+
+
+/* FIFO Control Register */
+#define URFC_URFRT (3 << 6) /* Receive FIFO Trigger Level */
+#define URFC_URFRT_1 (0 << 6)
+#define URFC_URFRT_4 (1 << 6)
+#define URFC_URFRT_8 (2 << 6)
+#define URFC_URFRT_14 (3 << 6)
+#define URFC_URTFR (1 << 2) /* Transmit FIFO Reset */
+#define URFC_URRFR (1 << 1) /* Receive FIFO Reset */
+#define URFC_URFE (1 << 0) /* FIFO Enable */
+
+/* Line Control Register */
+#define URLC_URSBC (1 << 6) /* Set Break Condition */
+#define URLC_PARITY (7 << 3) /* Parity */
+#define URPE_NONE (0 << 3)
+#define URPE_ODD (1 << 3)
+#define URPE_EVEN (3 << 3)
+#define URPE_MARK (5 << 3)
+#define URPE_SPACE (7 << 3)
+#define URLC_URSB (1 << 2) /* Stop Bits */
+#define URLC_URCL (3 << 0) /* Character Length */
+#define URCL_5 (0 << 0)
+#define URCL_6 (1 << 0)
+#define URCL_7 (2 << 0)
+#define URCL_8 (3 << 0)
+
+/* Modem Control Register */
+#define URMC_URLB (1 << 4) /* Loop-back mode */
+#define URMC_UROUT2 (1 << 3) /* OUT2 signal */
+#define URMC_UROUT1 (1 << 2) /* OUT1 signal */
+#define URMC_URRTS (1 << 1) /* Request to Send */
+#define URMC_URDTR (1 << 0) /* Data Terminal Ready */
+
+/* Line Status Register */
+#define URLS_URRFE (1 << 7) /* Receive FIFO Error */
+#define URLS_URTE (1 << 6) /* Transmit Empty */
+#define URLS_URTHRE (1 << 5) /* Transmit Holding Register Empty */
+#define URLS_URBI (1 << 4) /* Break Interrupt */
+#define URLS_URFE (1 << 3) /* Framing Error */
+#define URLS_URPE (1 << 2) /* Parity Error */
+#define URLS_URROE (1 << 1) /* Receive Overrun Error */
+#define URLS_URDR (1 << 0) /* Receive Data Ready */
+
+/* Modem Status Register */
+#define URMS_URDCD (1 << 7) /* Data Carrier Detect */
+#define URMS_URRI (1 << 6) /* Ring Indicator */
+#define URMS_URDSR (1 << 5) /* Data Set Ready */
+#define URMS_URCTS (1 << 4) /* Clear to Send */
+#define URMS_URDDCD (1 << 3) /* Delta Data Carrier Detect */
+#define URMS_URTERI (1 << 2) /* Trailing Edge Ring Indicator */
+#define URMS_URDDST (1 << 1) /* Delta Data Set Ready */
+#define URMS_URDCTS (1 << 0) /* Delta Clear to Send */
+
+/* Status Register */
+#define USR_UTI (1 << 0) /* Timeout Indication */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/regs-wan.h
+ *
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * KS8695 - WAN Registers and bit definitions.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef KS8695_WAN_H
+#define KS8695_WAN_H
+
+#define KS8695_WAN_OFFSET (0xF0000 + 0x6000)
+#define KS8695_WAN_VA (KS8695_IO_VA + KS8695_WAN_OFFSET)
+#define KS8695_WAN_PA (KS8695_IO_PA + KS8695_WAN_OFFSET)
+
+
+/*
+ * WAN registers
+ */
+#define KS8695_WMDTXC (0x00) /* DMA Transmit Control */
+#define KS8695_WMDRXC (0x04) /* DMA Receive Control */
+#define KS8695_WMDTSC (0x08) /* DMA Transmit Start Command */
+#define KS8695_WMDRSC (0x0c) /* DMA Receive Start Command */
+#define KS8695_WTDLB (0x10) /* Transmit Descriptor List Base Address */
+#define KS8695_WRDLB (0x14) /* Receive Descriptor List Base Address */
+#define KS8695_WMAL (0x18) /* MAC Station Address Low */
+#define KS8695_WMAH (0x1c) /* MAC Station Address High */
+#define KS8695_WMAAL_(n) (0x80 + ((n)*8)) /* MAC Additional Station Address (0..15) Low */
+#define KS8695_WMAAH_(n) (0x84 + ((n)*8)) /* MAC Additional Station Address (0..15) High */
+
+
+/* DMA Transmit Control Register */
+#define WMDTXC_WMTRST (1 << 31) /* Soft Reset */
+#define WMDTXC_WMTBS (0x3f << 24) /* Transmit Burst Size */
+#define WMDTXC_WMTUCG (1 << 18) /* Transmit UDP Checksum Generate */
+#define WMDTXC_WMTTCG (1 << 17) /* Transmit TCP Checksum Generate */
+#define WMDTXC_WMTICG (1 << 16) /* Transmit IP Checksum Generate */
+#define WMDTXC_WMTFCE (1 << 9) /* Transmit Flow Control Enable */
+#define WMDTXC_WMTLB (1 << 8) /* Loopback mode */
+#define WMDTXC_WMTEP (1 << 2) /* Transmit Enable Padding */
+#define WMDTXC_WMTAC (1 << 1) /* Transmit Add CRC */
+#define WMDTXC_WMTE (1 << 0) /* TX Enable */
+
+/* DMA Receive Control Register */
+#define WMDRXC_WMRBS (0x3f << 24) /* Receive Burst Size */
+#define WMDRXC_WMRUCC (1 << 18) /* Receive UDP Checksum check */
+#define WMDRXC_WMRTCG (1 << 17) /* Receive TCP Checksum check */
+#define WMDRXC_WMRICG (1 << 16) /* Receive IP Checksum check */
+#define WMDRXC_WMRFCE (1 << 9) /* Receive Flow Control Enable */
+#define WMDRXC_WMRB (1 << 6) /* Receive Broadcast */
+#define WMDRXC_WMRM (1 << 5) /* Receive Multicast */
+#define WMDRXC_WMRU (1 << 4) /* Receive Unicast */
+#define WMDRXC_WMRERR (1 << 3) /* Receive Error Frame */
+#define WMDRXC_WMRA (1 << 2) /* Receive All */
+#define WMDRXC_WMRE (1 << 0) /* RX Enable */
+
+/* Additional Station Address High */
+#define WMAAH_E (1 << 31) /* Address Enabled */
+
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-s3c2410/system.h
+ *
+ * Copyright (C) 2006 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * KS8695 - System function defines and includes
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+
+#include <asm/io.h>
+#include <asm/arch/regs-timer.h>
+
+static void arch_idle(void)
+{
+ /*
+ * This should do all the clock switching
+ * and wait for interrupt tricks,
+ */
+ cpu_do_idle();
+
+}
+
+static void arch_reset(char mode)
+{
+ unsigned int reg;
+
+ if (mode == 's')
+ cpu_reset(0);
+
+ /* disable timer0 */
+ reg = __raw_readl(KS8695_TMR_VA + KS8695_TMCON);
+ __raw_writel(reg & ~TMCON_T0EN, KS8695_TMR_VA + KS8695_TMCON);
+
+ /* enable watchdog mode */
+ __raw_writel((10 << 8) | T0TC_WATCHDOG, KS8695_TMR_VA + KS8695_T0TC);
+
+ /* re-enable timer0 */
+ __raw_writel(reg | TMCON_T0EN, KS8695_TMR_VA + KS8695_TMCON);
+}
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/timex.h
+ *
+ * Copyright (C) 2006 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * KS8695 - Time Parameters
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_TIMEX_H
+#define __ASM_ARCH_TIMEX_H
+
+/* timers are derived from MCLK, which is 25MHz */
+#define CLOCK_TICK_RATE 25000000
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/uncompress.h
+ *
+ * Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
+ * Copyright (C) 2006 Simtec Electronics
+ *
+ * KS8695 - Kernel uncompressor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_UNCOMPRESS_H
+#define __ASM_ARCH_UNCOMPRESS_H
+
+#include <asm/io.h>
+#include <asm/arch/regs-uart.h>
+
+static void putc(char c)
+{
+ while (!(__raw_readl(KS8695_UART_PA + KS8695_URLS) & URLS_URTHRE))
+ barrier();
+
+ __raw_writel(c, KS8695_UART_PA + KS8695_URTH);
+}
+
+static inline void flush(void)
+{
+ while (!(__raw_readl(KS8695_UART_PA + KS8695_URLS) & URLS_URTE))
+ barrier();
+}
+
+#define arch_decomp_setup()
+#define arch_decomp_wdog()
+
+#endif
--- /dev/null
+/*
+ * include/asm-arm/arch-ks8695/vmalloc.h
+ *
+ * Copyright (C) 2006 Ben Dooks
+ * Copyright (C) 2006 Simtec Electronics <linux@simtec.co.uk>
+ *
+ * KS8695 vmalloc definition
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_VMALLOC_H
+#define __ASM_ARCH_VMALLOC_H
+
+#define VMALLOC_END (KS8695_IO_VA & PGDIR_MASK)
+
+#endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff