--- /dev/null
+menu "ST-Ericsson platform type"
+ depends on ARCH_U8500
+
+comment "ST-Ericsson Multicore Mobile Platforms"
+
+config MACH_U8500_MOP
+ bool "U8500 Early Development platform"
+ default y
+ select ARM_GIC
+ select HAS_MTU
+ help
+ Include support for mop500 development platform
+ based on U8500 architecture. The platform is based
+ on early drop silicon version of 8500.
+endmenu
--- /dev/null
+#
+# Makefile for the linux kernel, U8500 machine.
+#
+
+obj-y := clock.o
+obj-$(CONFIG_ARCH_U8500) += cpu-u8500.o
+obj-$(CONFIG_MACH_U8500_MOP) += board-mop500.o
+obj-$(CONFIG_SMP) += platsmp.o headsmp.o localtimer.o
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson
+ *
+ * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/pl022.h>
+#include <linux/spi/spi.h>
+
+#include <asm/localtimer.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <plat/mtu.h>
+
+#include <mach/hardware.h>
+#include <mach/setup.h>
+
+#define __MEM_4K_RESOURCE(x) \
+ .res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
+
+/* These are active devices on this board */
+static struct amba_device uart0_device = {
+ .dev = { .init_name = "uart0" },
+ __MEM_4K_RESOURCE(U8500_UART0_BASE),
+ .irq = {IRQ_UART0, NO_IRQ},
+};
+
+static struct amba_device uart1_device = {
+ .dev = { .init_name = "uart1" },
+ __MEM_4K_RESOURCE(U8500_UART1_BASE),
+ .irq = {IRQ_UART1, NO_IRQ},
+};
+
+static struct amba_device uart2_device = {
+ .dev = { .init_name = "uart2" },
+ __MEM_4K_RESOURCE(U8500_UART2_BASE),
+ .irq = {IRQ_UART2, NO_IRQ},
+};
+
+static void ab4500_spi_cs_control(u32 command)
+{
+ /* set the FRM signal, which is CS - TODO */
+}
+
+struct pl022_config_chip ab4500_chip_info = {
+ .lbm = LOOPBACK_DISABLED,
+ .com_mode = INTERRUPT_TRANSFER,
+ .iface = SSP_INTERFACE_MOTOROLA_SPI,
+ /* we can act as master only */
+ .hierarchy = SSP_MASTER,
+ .slave_tx_disable = 0,
+ .endian_rx = SSP_RX_MSB,
+ .endian_tx = SSP_TX_MSB,
+ .data_size = SSP_DATA_BITS_24,
+ .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
+ .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
+ .clk_phase = SSP_CLK_SECOND_EDGE,
+ .clk_pol = SSP_CLK_POL_IDLE_HIGH,
+ .cs_control = ab4500_spi_cs_control,
+};
+
+static struct spi_board_info u8500_spi_devices[] = {
+ {
+ .modalias = "ab4500",
+ .controller_data = &ab4500_chip_info,
+ .max_speed_hz = 12000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = SPI_MODE_0,
+ .irq = IRQ_AB4500,
+ },
+};
+
+static struct pl022_ssp_controller ssp0_platform_data = {
+ .bus_id = 0,
+ /* pl022 not yet supports dma */
+ .enable_dma = 0,
+ /* on this platform, gpio 31,142,144,214 &
+ * 224 are connected as chip selects
+ */
+ .num_chipselect = 5,
+};
+
+static struct amba_device pl022_device = {
+ .dev = {
+ .coherent_dma_mask = ~0,
+ .init_name = "pl022",
+ .platform_data = &ssp0_platform_data,
+ },
+ .res = {
+ .start = U8500_SSP0_BASE,
+ .end = U8500_SSP0_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ .irq = {IRQ_SSP0, NO_IRQ },
+ /* ST-Ericsson modified id */
+ .periphid = SSP_PER_ID,
+};
+
+static struct amba_device *amba_devs[] __initdata = {
+ &uart0_device,
+ &uart1_device,
+ &uart2_device,
+ &pl022_device,
+};
+
+static void __init u8500_timer_init(void)
+{
+#ifdef CONFIG_LOCAL_TIMERS
+ /* Setup the local timer base */
+ twd_base = __io_address(U8500_TWD_BASE);
+#endif
+ /* Setup the MTU base */
+ mtu_base = __io_address(U8500_MTU0_BASE);
+
+ nmdk_timer_init();
+}
+
+static struct sys_timer u8500_timer = {
+ .init = u8500_timer_init,
+};
+
+static void __init u8500_init_machine(void)
+{
+ int i;
+
+ /* Register the active AMBA devices on this board */
+ for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
+ amba_device_register(amba_devs[i], &iomem_resource);
+
+ spi_register_board_info(u8500_spi_devices,
+ ARRAY_SIZE(u8500_spi_devices));
+
+ u8500_init_devices();
+}
+
+MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
+ /* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
+ .phys_io = U8500_UART2_BASE,
+ .io_pg_offst = (IO_ADDRESS(U8500_UART2_BASE) >> 18) & 0xfffc,
+ .boot_params = 0x100,
+ .map_io = u8500_map_io,
+ .init_irq = u8500_init_irq,
+ /* we re-use nomadik timer here */
+ .timer = &u8500_timer,
+ .init_machine = u8500_init_machine,
+MACHINE_END
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson
+ *
+ * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/amba/bus.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware/gic.h>
+#include <asm/mach/map.h>
+#include <mach/hardware.h>
+
+/* add any platform devices here - TODO */
+static struct platform_device *platform_devs[] __initdata = {
+ /* yet to be added, add i2c0, gpio.. */
+};
+
+#define __IO_DEV_DESC(x, sz) { \
+ .virtual = IO_ADDRESS(x), \
+ .pfn = __phys_to_pfn(x), \
+ .length = sz, \
+ .type = MT_DEVICE, \
+}
+
+/* minimum static i/o mapping required to boot U8500 platforms */
+static struct map_desc u8500_io_desc[] __initdata = {
+ __IO_DEV_DESC(U8500_GIC_CPU_BASE, SZ_4K),
+ __IO_DEV_DESC(U8500_GIC_DIST_BASE, SZ_4K),
+ __IO_DEV_DESC(U8500_MTU0_BASE, SZ_4K),
+ __IO_DEV_DESC(U8500_TWD_BASE, SZ_4K),
+ __IO_DEV_DESC(U8500_SCU_BASE, SZ_4K),
+ __IO_DEV_DESC(U8500_BACKUPRAM0_BASE, SZ_8K),
+};
+
+void __init u8500_map_io(void)
+{
+ iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc));
+}
+
+void __init u8500_init_irq(void)
+{
+ gic_dist_init(0, __io_address(U8500_GIC_DIST_BASE), 29);
+ gic_cpu_init(0, __io_address(U8500_GIC_CPU_BASE));
+}
+
+/*
+ * This function is called from the board init
+ */
+void __init u8500_init_devices(void)
+{
+ /* Register the platform devices */
+ platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
+
+ return ;
+}
--- /dev/null
+/*
+ * Copyright (c) 2009 ST-Ericsson
+ * This file is based ARM Realview platform
+ * Copyright (c) 2003 ARM Limited
+ * All Rights Reserved
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/linkage.h>
+#include <linux/init.h>
+
+ __INIT
+
+/*
+ * U8500 specific entry point for secondary CPUs.
+ */
+ENTRY(u8500_secondary_startup)
+ mrc p15, 0, r0, c0, c0, 5
+ and r0, r0, #15
+ adr r4, 1f
+ ldmia r4, {r5, r6}
+ sub r4, r4, r5
+ add r6, r6, r4
+ dsb
+pen: ldr r7, [r6]
+ cmp r7, r0
+ bne pen
+
+ /*
+ * we've been released from the holding pen: secondary_stack
+ * should now contain the SVC stack for this core
+ */
+ b secondary_startup
+
+1: .long .
+ .long pen_release
--- /dev/null
+/*
+ * Debugging macro include header
+ *
+ * Copyright (C) 2009 ST-Ericsson
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+ .macro addruart,rx
+ mrc p15, 0, \rx, c1, c0
+ tst \rx, #1 @MMU enabled?
+ moveq \rx, #0x80000000 @MMU off, Physical address
+ movne \rx, #0xF0000000 @MMU on, Virtual address
+ orr \rx, \rx, #0x7000
+ .endm
+
+#include <asm/hardware/debug-pl01x.S>
--- /dev/null
+/*
+ * Low-level IRQ helper macros for U8500 platforms
+ *
+ * Copyright (C) 2009 ST-Ericsson.
+ *
+ * This file is a copy of ARM Realview platform.
+ * -just satisfied checkpatch script.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <mach/hardware.h>
+#include <asm/hardware/gic.h>
+
+ .macro disable_fiq
+ .endm
+
+ .macro get_irqnr_preamble, base, tmp
+ ldr \base, =IO_ADDRESS(U8500_GIC_CPU_BASE)
+ .endm
+
+ .macro arch_ret_to_user, tmp1, tmp2
+ .endm
+
+ /*
+ * The interrupt numbering scheme is defined in the
+ * interrupt controller spec. To wit:
+ *
+ * Interrupts 0-15 are IPI
+ * 16-28 are reserved
+ * 29-31 are local. We allow 30 to be used for the watchdog.
+ * 32-1020 are global
+ * 1021-1022 are reserved
+ * 1023 is "spurious" (no interrupt)
+ *
+ * For now, we ignore all local interrupts so only return an
+ * interrupt if it's between 30 and 1020. The test_for_ipi
+ * routine below will pick up on IPIs.
+ *
+ * A simple read from the controller will tell us the number
+ * of the highest priority enabled interrupt. We then just
+ * need to check whether it is in the valid range for an
+ * IRQ (30-1020 inclusive).
+ */
+
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+ /* bits 12-10 = src CPU, 9-0 = int # */
+ ldr \irqstat, [\base, #GIC_CPU_INTACK]
+
+ ldr \tmp, =1021
+
+ bic \irqnr, \irqstat, #0x1c00
+
+ cmp \irqnr, #29
+ cmpcc \irqnr, \irqnr
+ cmpne \irqnr, \tmp
+ cmpcs \irqnr, \irqnr
+
+ .endm
+
+ /* We assume that irqstat (the raw value of the IRQ
+ * acknowledge register) is preserved from the macro above.
+ * If there is an IPI, we immediately signal end of
+ * interrupt on the controller, since this requires the
+ * original irqstat value which we won't easily be able
+ * to recreate later.
+ */
+
+ .macro test_for_ipi, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #16
+ strcc \irqstat, [\base, #GIC_CPU_EOI]
+ cmpcs \irqnr, \irqnr
+ .endm
+
+ /* As above, this assumes that irqstat and base
+ * are preserved..
+ */
+
+ .macro test_for_ltirq, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ mov \tmp, #0
+ cmp \irqnr, #29
+ moveq \tmp, #1
+ streq \irqstat, [\base, #GIC_CPU_EOI]
+ cmp \tmp, #0
+ .endm
--- /dev/null
+/*
+ * Copyright (C) 2009 ST-Ericsson
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/*
+ * Physical DRAM offset.
+ */
+#define PHYS_OFFSET UL(0x00000000)
+#define BUS_OFFSET UL(0x00000000)
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2009 ST-Ericsson.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * These symbols are needed for board-specific files to call their
+ * own cpu-specific files
+ */
+#ifndef __ASM_ARCH_SETUP_H
+#define __ASM_ARCH_SETUP_H
+
+#include <asm/mach/time.h>
+#include <linux/init.h>
+
+extern void u8500_map_io(void);
+extern void u8500_init_devices(void);
+extern void u8500_init_irq(void);
+/* We re-use nomadik_timer for this platform */
+extern void nmdk_timer_init(void);
+
+#endif /* __ASM_ARCH_SETUP_H */
--- /dev/null
+/*
+ * This file is based ARM realview platform.
+ * Copyright (C) ARM Limited.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#ifndef ASMARM_ARCH_SMP_H
+#define ASMARM_ARCH_SMP_H
+
+#include <asm/hardware/gic.h>
+
+/* This is required to wakeup the secondary core */
+extern void u8500_secondary_startup(void);
+
+#define hard_smp_processor_id() \
+ ({ \
+ unsigned int cpunum; \
+ __asm__("mrc p15, 0, %0, c0, c0, 5" \
+ : "=r" (cpunum)); \
+ cpunum &= 0x0F; \
+ })
+
+/*
+ * We use IRQ1 as the IPI
+ */
+static inline void smp_cross_call(const struct cpumask *mask)
+{
+ gic_raise_softirq(mask, 1);
+}
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2009 ST-Ericsson.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+
+static inline void arch_idle(void)
+{
+ /*
+ * This should do all the clock switching
+ * and wait for interrupt tricks
+ */
+ cpu_do_idle();
+}
+
+static inline void arch_reset(char mode, const char *cmd)
+{
+ /* yet to be implemented - TODO */
+}
+
+#endif
--- /dev/null
+#ifndef __ASM_ARCH_TIMEX_H
+#define __ASM_ARCH_TIMEX_H
+
+#define CLOCK_TICK_RATE 110000000
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2009 ST-Ericsson
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __ASM_ARCH_UNCOMPRESS_H
+#define __ASM_ARCH_UNCOMPRESS_H
+
+#include <asm/setup.h>
+#include <linux/io.h>
+#include <mach/hardware.h>
+
+#define U8500_UART_DR 0x80007000
+#define U8500_UART_LCRH 0x8000702c
+#define U8500_UART_CR 0x80007030
+#define U8500_UART_FR 0x80007018
+
+static void putc(const char c)
+{
+ /* Do nothing if the UART is not enabled. */
+ if (!(readb(U8500_UART_CR) & 0x1))
+ return;
+
+ if (c == '\n')
+ putc('\r');
+
+ while (readb(U8500_UART_FR) & (1 << 5))
+ barrier();
+ writeb(c, U8500_UART_DR);
+}
+
+static void flush(void)
+{
+ if (!(readb(U8500_UART_CR) & 0x1))
+ return;
+ while (readb(U8500_UART_FR) & (1 << 3))
+ barrier();
+}
+
+static inline void arch_decomp_setup(void)
+{
+}
+
+#define arch_decomp_wdog() /* nothing to do here */
+
+#endif /* __ASM_ARCH_UNCOMPRESS_H */
--- /dev/null
+/*
+ * Copyright (C) 2009 ST-Ericsson
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#define VMALLOC_END 0xf0000000
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson
+ * Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
+ *
+ * This file is heavily based on relaview platform, almost a copy.
+ *
+ * Copyright (C) 2002 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <linux/clockchips.h>
+
+#include <asm/irq.h>
+#include <asm/smp_twd.h>
+#include <asm/localtimer.h>
+
+/*
+ * Setup the local clock events for a CPU.
+ */
+void __cpuinit local_timer_setup(struct clock_event_device *evt)
+{
+ evt->irq = IRQ_LOCALTIMER;
+ twd_timer_setup(evt);
+}
--- /dev/null
+/*
+ * Copyright (C) 2002 ARM Ltd.
+ * Copyright (C) 2008 STMicroelctronics.
+ * Copyright (C) 2009 ST-Ericsson.
+ * Author: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
+ *
+ * This file is based on arm realview platform
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/smp.h>
+#include <linux/io.h>
+
+#include <asm/cacheflush.h>
+#include <asm/localtimer.h>
+#include <asm/smp_scu.h>
+#include <mach/hardware.h>
+
+/*
+ * control for which core is the next to come out of the secondary
+ * boot "holding pen"
+ */
+volatile int __cpuinitdata pen_release = -1;
+
+static unsigned int __init get_core_count(void)
+{
+ return scu_get_core_count(__io_address(U8500_SCU_BASE));
+}
+
+static DEFINE_SPINLOCK(boot_lock);
+
+void __cpuinit platform_secondary_init(unsigned int cpu)
+{
+ trace_hardirqs_off();
+
+ /*
+ * if any interrupts are already enabled for the primary
+ * core (e.g. timer irq), then they will not have been enabled
+ * for us: do so
+ */
+ gic_cpu_init(0, __io_address(U8500_GIC_CPU_BASE));
+
+ /*
+ * let the primary processor know we're out of the
+ * pen, then head off into the C entry point
+ */
+ pen_release = -1;
+
+ /*
+ * Synchronise with the boot thread.
+ */
+ spin_lock(&boot_lock);
+ spin_unlock(&boot_lock);
+}
+
+int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+ unsigned long timeout;
+
+ /*
+ * set synchronisation state between this boot processor
+ * and the secondary one
+ */
+ spin_lock(&boot_lock);
+
+ /*
+ * The secondary processor is waiting to be released from
+ * the holding pen - release it, then wait for it to flag
+ * that it has been released by resetting pen_release.
+ */
+ pen_release = cpu;
+ flush_cache_all();
+
+ timeout = jiffies + (1 * HZ);
+ while (time_before(jiffies, timeout)) {
+ if (pen_release == -1)
+ break;
+ }
+
+ /*
+ * now the secondary core is starting up let it run its
+ * calibrations, then wait for it to finish
+ */
+ spin_unlock(&boot_lock);
+
+ return pen_release != -1 ? -ENOSYS : 0;
+}
+
+static void __init wakeup_secondary(void)
+{
+ /* nobody is to be released from the pen yet */
+ pen_release = -1;
+
+ /*
+ * write the address of secondary startup into the backup ram register
+ * at offset 0x1FF4, then write the magic number 0xA1FEED01 to the
+ * backup ram register at offset 0x1FF0, which is what boot rom code
+ * is waiting for. This would wake up the secondary core from WFE
+ */
+#define U8500_CPU1_JUMPADDR_OFFSET 0x1FF4
+ __raw_writel(virt_to_phys(u8500_secondary_startup),
+ (void __iomem *)IO_ADDRESS(U8500_BACKUPRAM0_BASE) +
+ U8500_CPU1_JUMPADDR_OFFSET);
+
+#define U8500_CPU1_WAKEMAGIC_OFFSET 0x1FF0
+ __raw_writel(0xA1FEED01,
+ (void __iomem *)IO_ADDRESS(U8500_BACKUPRAM0_BASE) +
+ U8500_CPU1_WAKEMAGIC_OFFSET);
+
+ /* make sure write buffer is drained */
+ mb();
+}
+
+/*
+ * Initialise the CPU possible map early - this describes the CPUs
+ * which may be present or become present in the system.
+ */
+void __init smp_init_cpus(void)
+{
+ unsigned int i, ncores = get_core_count();
+
+ for (i = 0; i < ncores; i++)
+ set_cpu_possible(i, true);
+}
+
+void __init smp_prepare_cpus(unsigned int max_cpus)
+{
+ unsigned int ncores = get_core_count();
+ unsigned int cpu = smp_processor_id();
+ int i;
+
+ /* sanity check */
+ if (ncores == 0) {
+ printk(KERN_ERR
+ "U8500: strange CM count of 0? Default to 1\n");
+ ncores = 1;
+ }
+
+ if (ncores > num_possible_cpus()) {
+ printk(KERN_WARNING
+ "U8500: no. of cores (%d) greater than configured "
+ "maximum of %d - clipping\n",
+ ncores, num_possible_cpus());
+ ncores = num_possible_cpus();
+ }
+
+ smp_store_cpu_info(cpu);
+
+ /*
+ * are we trying to boot more cores than exist?
+ */
+ if (max_cpus > ncores)
+ max_cpus = ncores;
+
+ /*
+ * Initialise the present map, which describes the set of CPUs
+ * actually populated at the present time.
+ */
+ for (i = 0; i < max_cpus; i++)
+ set_cpu_present(i, true);
+
+ if (max_cpus > 1) {
+ /*
+ * Enable the local timer or broadcast device for the
+ * boot CPU, but only if we have more than one CPU.
+ */
+ percpu_timer_setup();
+ scu_enable(__io_address(U8500_SCU_BASE));
+ wakeup_secondary();
+ }
+}
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff