include/linux/version.h
include/linux/utsrelease.h
include/linux/bounds.h
+include/generated
# stgit generated dirs
patches-*
iii. Plugging the queue to batch requests in anticipation of opportunities for
merge/sort optimizations
-This is just the same as in 2.4 so far, though per-device unplugging
-support is anticipated for 2.5. Also with a priority-based i/o scheduler,
-such decisions could be based on request priorities.
-
Plugging is an approach that the current i/o scheduling algorithm resorts to so
that it collects up enough requests in the queue to be able to take
advantage of the sorting/merging logic in the elevator. If the
queue is empty when a request comes in, then it plugs the request queue
-(sort of like plugging the bottom of a vessel to get fluid to build up)
+(sort of like plugging the bath tub of a vessel to get fluid to build up)
till it fills up with a few more requests, before starting to service
the requests. This provides an opportunity to merge/sort the requests before
passing them down to the device. There are various conditions when the queue is
unplugged (to open up the flow again), either through a scheduled task or
could be on demand. For example wait_on_buffer sets the unplugging going
-(by running tq_disk) so the read gets satisfied soon. So in the read case,
-the queue gets explicitly unplugged as part of waiting for completion,
-in fact all queues get unplugged as a side-effect.
+through sync_buffer() running blk_run_address_space(mapping). Or the caller
+can do it explicity through blk_unplug(bdev). So in the read case,
+the queue gets explicitly unplugged as part of waiting for completion on that
+buffer. For page driven IO, the address space ->sync_page() takes care of
+doing the blk_run_address_space().
Aside:
This is kind of controversial territory, as it's not clear if plugging is
multi-page bios being queued in one shot, we may not need to wait to merge
a big request from the broken up pieces coming by.
- Per-queue granularity unplugging (still a Todo) may help reduce some of the
- concerns with just a single tq_disk flush approach. Something like
- blk_kick_queue() to unplug a specific queue (right away ?)
- or optionally, all queues, is in the plan.
-
4.4 I/O contexts
I/O contexts provide a dynamically allocated per process data area. They may
be used in I/O schedulers, and in the block layer (could be used for IO statis,
be probed later if another device registers. (Which is OK, since
this interface is only for use with non-hotpluggable devices.)
+
+Early Platform Devices and Drivers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The early platform interfaces provide platform data to platform device
+drivers early on during the system boot. The code is built on top of the
+early_param() command line parsing and can be executed very early on.
+
+Example: "earlyprintk" class early serial console in 6 steps
+
+1. Registering early platform device data
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The architecture code registers platform device data using the function
+early_platform_add_devices(). In the case of early serial console this
+should be hardware configuration for the serial port. Devices registered
+at this point will later on be matched against early platform drivers.
+
+2. Parsing kernel command line
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The architecture code calls parse_early_param() to parse the kernel
+command line. This will execute all matching early_param() callbacks.
+User specified early platform devices will be registered at this point.
+For the early serial console case the user can specify port on the
+kernel command line as "earlyprintk=serial.0" where "earlyprintk" is
+the class string, "serial" is the name of the platfrom driver and
+0 is the platform device id. If the id is -1 then the dot and the
+id can be omitted.
+
+3. Installing early platform drivers belonging to a certain class
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The architecture code may optionally force registration of all early
+platform drivers belonging to a certain class using the function
+early_platform_driver_register_all(). User specified devices from
+step 2 have priority over these. This step is omitted by the serial
+driver example since the early serial driver code should be disabled
+unless the user has specified port on the kernel command line.
+
+4. Early platform driver registration
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+Compiled-in platform drivers making use of early_platform_init() are
+automatically registered during step 2 or 3. The serial driver example
+should use early_platform_init("earlyprintk", &platform_driver).
+
+5. Probing of early platform drivers belonging to a certain class
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The architecture code calls early_platform_driver_probe() to match
+registered early platform devices associated with a certain class with
+registered early platform drivers. Matched devices will get probed().
+This step can be executed at any point during the early boot. As soon
+as possible may be good for the serial port case.
+
+6. Inside the early platform driver probe()
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The driver code needs to take special care during early boot, especially
+when it comes to memory allocation and interrupt registration. The code
+in the probe() function can use is_early_platform_device() to check if
+it is called at early platform device or at the regular platform device
+time. The early serial driver performs register_console() at this point.
+
+For further information, see <linux/platform_device.h>.
data transfers.
POHMELFS clients operate with a working set of servers and are capable of balancing read-only
-operations (like lookups or directory listings) between them.
+operations (like lookups or directory listings) between them according to IO priorities.
Administrators can add or remove servers from the set at run-time via special commands (described
-in Documentation/pohmelfs/info.txt file). Writes are replicated to all servers.
+in Documentation/pohmelfs/info.txt file). Writes are replicated to all servers, which are connected
+with write permission turned on. IO priority and permissions can be changed in run-time.
POHMELFS is capable of full data channel encryption and/or strong crypto hashing.
One can select any kernel supported cipher, encryption mode, hash type and operation mode
POHMELFS usage information.
-Mount options:
+Mount options.
+All but index, number of crypto threads and maximum IO size can changed via remount.
+
idx=%u
Each mountpoint is associated with a special index via this option.
Administrator can add or remove servers from the given index, so all mounts,
Usage examples.
-Add (or remove if it already exists) server server1.net:1025 into the working set with index $idx
+Add server server1.net:1025 into the working set with index $idx
with appropriate hash algorithm and key file and cipher algorithm, mode and key file:
-$cfg -a server1.net -p 1025 -i $idx -K $hash_key -k $cipher_key
+$cfg A add -a server1.net -p 1025 -i $idx -K $hash_key -k $cipher_key
Mount filesystem with given index $idx to /mnt mountpoint.
Client will connect to all servers specified in the working set via previous command:
mount -t pohmel -o idx=$idx q /mnt
-One can add or remove servers from working set after mounting too.
+Change permissions to read-only (-I 1 option, '-I 2' - write-only, 3 - rw):
+$cfg A modify -a server1.net -p 1025 -i $idx -I 1
+
+Change IO priority to 123 (node with the highest priority gets read requests).
+$cfg A modify -a server1.net -p 1025 -i $idx -P 123
+One can check currect status of all connections in the mountstats file:
+# cat /proc/$PID/mountstats
+...
+device none mounted on /mnt with fstype pohmel
+idx addr(:port) socket_type protocol active priority permissions
+0 server1.net:1026 1 6 1 250 1
+0 server2.net:1025 1 6 1 123 3
Server installation.
#arch/m68k/fpsp040/Makefile
ldflags-y := -x
+ subdir-ccflags-y, subdir-asflags-y
+ The two flags listed above are similar to ccflags-y and as-falgs-y.
+ The difference is that the subdir- variants has effect for the kbuild
+ file where tey are present and all subdirectories.
+ Options specified using subdir-* are added to the commandline before
+ the options specified using the non-subdir variants.
+
+ Example:
+ subdir-ccflags-y := -Werror
+
CFLAGS_$@, AFLAGS_$@
CFLAGS_$@ and AFLAGS_$@ only apply to commands in current
./include/asm/setup.h as COMMAND_LINE_SIZE.
- acpi= [HW,ACPI,X86-64,i386]
+ acpi= [HW,ACPI,X86]
Advanced Configuration and Power Interface
Format: { force | off | ht | strict | noirq | rsdt }
force -- enable ACPI if default was off
acpi_osi="!string2" # remove built-in string2
acpi_osi= # disable all strings
- acpi_pm_good [X86-32,X86-64]
+ acpi_pm_good [X86]
Override the pmtimer bug detection: force the kernel
to assume that this machine's pmtimer latches its value
and always returns good values.
power state again in power transition.
1 : disable the power state check
+ acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
+ Format: { level | edge | high | low }
+
+ acpi_serialize [HW,ACPI] force serialization of AML methods
+
+ acpi_skip_timer_override [HW,ACPI]
+ Recognize and ignore IRQ0/pin2 Interrupt Override.
+ For broken nForce2 BIOS resulting in XT-PIC timer.
+
+ acpi_sleep= [HW,ACPI] Sleep options
+ Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
+ old_ordering, s4_nonvs }
+ See Documentation/power/video.txt for information on
+ s3_bios and s3_mode.
+ s3_beep is for debugging; it makes the PC's speaker beep
+ as soon as the kernel's real-mode entry point is called.
+ s4_nohwsig prevents ACPI hardware signature from being
+ used during resume from hibernation.
+ old_ordering causes the ACPI 1.0 ordering of the _PTS
+ control method, with respect to putting devices into
+ low power states, to be enforced (the ACPI 2.0 ordering
+ of _PTS is used by default).
+ s4_nonvs prevents the kernel from saving/restoring the
+ ACPI NVS memory during hibernation.
+
+ acpi_use_timer_override [HW,ACPI]
+ Use timer override. For some broken Nvidia NF5 boards
+ that require a timer override, but don't have HPET
+
acpi_enforce_resources= [ACPI]
{ strict | lax | no }
Check for resource conflicts between native drivers
ad1848= [HW,OSS]
Format: <io>,<irq>,<dma>,<dma2>,<type>
+ add_efi_memmap [EFI; X86] Include EFI memory map in
+ kernel's map of available physical RAM.
+
advansys= [HW,SCSI]
See header of drivers/scsi/advansys.c.
Also note the kernel might malfunction if you disable
some critical bits.
- code_bytes [IA32/X86_64] How many bytes of object code to print
+ code_bytes [X86] How many bytes of object code to print
in an oops report.
Range: 0 - 8192
Default: 64
MTRR settings. This parameter disables that behavior,
possibly causing your machine to run very slowly.
- disable_timer_pin_1 [i386,x86-64]
+ disable_timer_pin_1 [X86]
Disable PIN 1 of APIC timer
Can be useful to work around chipset bugs.
UART at the specified I/O port or MMIO address.
The options are the same as for ttyS, above.
- earlyprintk= [X86-32,X86-64,SH,BLACKFIN]
+ earlyprintk= [X86,SH,BLACKFIN]
earlyprintk=vga
earlyprintk=serial[,ttySn[,baudrate]]
earlyprintk=dbgp
See Documentation/block/as-iosched.txt and
Documentation/block/deadline-iosched.txt for details.
- elfcorehdr= [IA64,PPC,SH,X86-32,X86_64]
+ elfcorehdr= [IA64,PPC,SH,X86]
Specifies physical address of start of kernel core
image elf header. Generally kexec loader will
pass this option to capture kernel.
See comment before marvel_specify_io7 in
arch/alpha/kernel/core_marvel.c.
- io_delay= [X86-32,X86-64] I/O delay method
+ io_delay= [X86] I/O delay method
0x80
Standard port 0x80 based delay
0xed
keepinitrd [HW,ARM]
- kernelcore=nn[KMG] [KNL,X86-32,IA-64,PPC,X86-64] This parameter
+ kernelcore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
specifies the amount of memory usable by the kernel
for non-movable allocations. The requested amount is
spread evenly throughout all nodes in the system. The
Configure the RouterBoard 532 series on-chip
Ethernet adapter MAC address.
- kstack=N [X86-32,X86-64] Print N words from the kernel stack
+ kstack=N [X86] Print N words from the kernel stack
in oops dumps.
l2cr= [PPC]
lapic [X86-32,APIC] Enable the local APIC even if BIOS
disabled it.
- lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer
+ lapic_timer_c2_ok [X86,APIC] trust the local apic timer
in C2 power state.
libata.dma= [LIBATA] DMA control
[KNL,SH] Allow user to override the default size for
per-device physically contiguous DMA buffers.
- memmap=exactmap [KNL,X86-32,X86_64] Enable setting of an exact
+ memmap=exactmap [KNL,X86] Enable setting of an exact
E820 memory map, as specified by the user.
Such memmap=exactmap lines can be constructed based on
BIOS output or other requirements. See the memmap=nn@ss
mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
reporting absolute coordinates, such as tablets
- movablecore=nn[KMG] [KNL,X86-32,IA-64,PPC,X86-64] This parameter
+ movablecore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
is similar to kernelcore except it specifies the
amount of memory used for migratable allocations.
If both kernelcore and movablecore is specified,
when a NMI is triggered.
Format: [state][,regs][,debounce][,die]
- nmi_watchdog= [KNL,BUGS=X86-32,X86-64] Debugging features for SMP kernels
+ nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels
Format: [panic,][num]
Valid num: 0,1,2
0 - turn nmi_watchdog off
nodsp [SH] Disable hardware DSP at boot time.
- noefi [X86-32,X86-64] Disable EFI runtime services support.
+ noefi [X86] Disable EFI runtime services support.
noexec [IA-64]
- noexec [X86-32,X86-64]
+ noexec [X86]
On X86-32 available only on PAE configured kernels.
noexec=on: enable non-executable mappings (default)
noexec=off: disable non-executable mappings
noirqdebug [X86-32] Disables the code which attempts to detect and
disable unhandled interrupt sources.
- no_timer_check [X86-32,X86_64,APIC] Disables the code which tests for
+ no_timer_check [X86,APIC] Disables the code which tests for
broken timer IRQ sources.
noisapnp [ISAPNP] Disables ISA PnP code.
disable the use of PCIE advanced error reporting.
nodomains [PCI] Disable support for multiple PCI
root domains (aka PCI segments, in ACPI-speak).
- nommconf [X86-32,X86_64] Disable use of MMCONFIG for PCI
+ nommconf [X86] Disable use of MMCONFIG for PCI
Configuration
nomsi [MSI] If the PCI_MSI kernel config parameter is
enabled, this kernel boot option can be used to
autoconfiguration.
Ranges are in pairs (memory base and size).
+ ports= [IP_VS_FTP] IPVS ftp helper module
+ Default is 21.
+ Up to 8 (IP_VS_APP_MAX_PORTS) ports
+ may be specified.
+ Format: <port>,<port>....
+
print-fatal-signals=
[KNL] debug: print fatal signals
print-fatal-signals=1: print segfault info to
reported either.
unknown_nmi_panic
- [X86-32,X86-64]
+ [X86]
Set unknown_nmi_panic=1 early on boot.
usbcore.autosuspend=
medium is write-protected).
Example: quirks=0419:aaf5:rl,0421:0433:rc
- vdso= [X86-32,SH,x86-64]
+ vdso= [X86,SH]
vdso=2: enable compat VDSO (default with COMPAT_VDSO)
vdso=1: enable VDSO (default)
vdso=0: disable VDSO mapping
- vdso32= [X86-32,X86-64]
+ vdso32= [X86]
vdso32=2: enable compat VDSO (default with COMPAT_VDSO)
vdso32=1: enable 32-bit VDSO (default)
vdso32=0: disable 32-bit VDSO mapping
/, /` - or, A Young Coder's Illustrated Hypervisor
\\"--\\ http://lguest.ozlabs.org
-Lguest is designed to be a minimal hypervisor for the Linux kernel, for
-Linux developers and users to experiment with virtualization with the
-minimum of complexity. Nonetheless, it should have sufficient
-features to make it useful for specific tasks, and, of course, you are
-encouraged to fork and enhance it (see drivers/lguest/README).
+Lguest is designed to be a minimal 32-bit x86 hypervisor for the Linux kernel,
+for Linux developers and users to experiment with virtualization with the
+minimum of complexity. Nonetheless, it should have sufficient features to
+make it useful for specific tasks, and, of course, you are encouraged to fork
+and enhance it (see drivers/lguest/README).
Features:
"Paravirtualized guest support" = Y
"Lguest guest support" = Y
"High Memory Support" = off/4GB
+ "PAE (Physical Address Extension) Support" = N
"Alignment value to which kernel should be aligned" = 0x100000
(CONFIG_PARAVIRT=y, CONFIG_LGUEST_GUEST=y, CONFIG_HIGHMEM64G=n and
CONFIG_PHYSICAL_ALIGN=0x100000)
To add ARP targets:
# echo +192.168.0.100 > /sys/class/net/bond0/bonding/arp_ip_target
# echo +192.168.0.101 > /sys/class/net/bond0/bonding/arp_ip_target
- NOTE: up to 10 target addresses may be specified.
+ NOTE: up to 16 target addresses may be specified.
To remove an ARP target:
# echo -192.168.0.100 > /sys/class/net/bond0/bonding/arp_ip_target
Recommended properties :
- - compatible : Should be "fsl-i2c" for parts compatible with
- Freescale I2C specifications.
+ - compatible : compatibility list with 2 entries, the first should
+ be "fsl,CHIP-i2c" where CHIP is the name of a compatible processor,
+ e.g. mpc8313, mpc8543, mpc8544, mpc5200 or mpc5200b. The second one
+ should be "fsl-i2c".
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- - dfsrr : boolean; if defined, indicates that this I2C device has
- a digital filter sampling rate register
- - fsl5200-clocking : boolean; if defined, indicated that this device
- uses the FSL 5200 clocking mechanism.
-
-Example :
- i2c@3000 {
- interrupt-parent = <40000>;
- interrupts = <1b 3>;
- reg = <3000 18>;
- device_type = "i2c";
- compatible = "fsl-i2c";
- dfsrr;
+ - fsl,preserve-clocking : boolean; if defined, the clock settings
+ from the bootloader are preserved (not touched).
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Examples :
+
+ i2c@3d00 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+ cell-index = <0>;
+ reg = <0x3d00 0x40>;
+ interrupts = <2 15 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ fsl,preserve-clocking;
};
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl,mpc8544-i2c", "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ clock-frequency = <400000>;
+ };
+
What `model` option values are available depends on the codec chip.
Check your codec chip from the codec proc file (see "Codec Proc-File"
section below). It will show the vendor/product name of your codec
-chip. Then, see Documentation/sound/alsa/HD-Audio-Modelstxt file,
+chip. Then, see Documentation/sound/alsa/HD-Audio-Models.txt file,
the section of HD-audio driver. You can find a list of codecs
and `model` options belonging to each codec. For example, for Realtek
ALC262 codec chip, pass `model=ultra` for devices that are compatible
Thus, the first thing you can do for any brand-new, unsupported and
non-working HD-audio hardware is to check HD-audio codec and several
-different `model` option values. If you have a luck, some of them
+different `model` option values. If you have any luck, some of them
might suit with your device well.
Some codecs such as ALC880 have a special model option `model=test`.
F: arch/arm/lib/floppydma.S
F: arch/arm/include/asm/floppy.h
+ARM PORT
+P: Russell King
+M: linux@arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+W: http://www.arm.linux.org.uk/
+S: Maintained
+F: arch/arm/
+
ARM PRIMECELL MMCI PL180/1 DRIVER
S: Orphan
F: drivers/mmc/host/mmci.*
L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
+ARM/CLKDEV SUPPORT
+P: Russell King
+M: linux@arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+F: arch/arm/common/clkdev.c
+F: arch/arm/include/asm/clkdev.h
+
ARM/COMPULAB CM-X270/EM-X270 and CM-X300 MACHINE SUPPORT
P: Mike Rapoport
M: mike@compulab.co.il
T: git git://gitorious.org/linux-gemini/mainline.git
S: Maintained
+ARM/EBSA110 MACHINE SUPPORT
+P: Russell King
+M: linux@arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+W: http://www.arm.linux.org.uk/
+S: Maintained
+F: arch/arm/mach-ebsa110/
+F: drivers/net/arm/am79c961a.*
+
ARM/EZX SMARTPHONES (A780, A910, A1200, E680, ROKR E2 and ROKR E6)
P: Daniel Ribeiro
M: drwyrm@gmail.com
L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
+ARM/FOOTBRIDGE ARCHITECTURE
+P: Russell King
+M: linux@arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+W: http://www.arm.linux.org.uk/
+S: Maintained
+F: arch/arm/include/asm/hardware/dec21285.h
+F: arch/arm/mach-footbridge/
+
ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
P: Sascha Hauer
M: kernel@pengutronix.de
L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
+ARM/RISCPC ARCHITECTURE
+P: Russell King
+M: linux@arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+W: http://www.arm.linux.org.uk/
+S: Maintained
+F: arch/arm/common/time-acorn.c
+F: arch/arm/include/asm/hardware/entry-macro-iomd.S
+F: arch/arm/include/asm/hardware/ioc.h
+F: arch/arm/include/asm/hardware/iomd.h
+F: arch/arm/include/asm/hardware/memc.h
+F: arch/arm/mach-rpc/
+F: drivers/net/arm/ether*
+F: drivers/scsi/arm/
+
ARM/SHARK MACHINE SUPPORT
P: Alexander Schulz
M: alex@shark-linux.de
W: http://www.shark-linux.de/shark.html
S: Maintained
-ARM/STRONGARM110 PORT
-P: Russell King
-M: rmk@arm.linux.org.uk
-L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
-W: http://www.arm.linux.org.uk/
-S: Maintained
-
ARM/S3C2410 ARM ARCHITECTURE
P: Ben Dooks
M: ben-linux@fluff.org
W: http://www.mcuos.com
S: Maintained
+ARM/VFP SUPPORT
+P: Russell King
+M: linux@arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+W: http://www.arm.linux.org.uk/
+S: Maintained
+F: arch/arm/vfp/
+
ARPD SUPPORT
P: Jonathan Layes
L: netdev@vger.kernel.org
F: Documentation/input/cs461x.txt
F: sound/pci/cs46xx/
+CLK API
+P: Russell King
+M: linux@arm.linux.org.uk
+F: include/linux/clk.h
+
CODA FILE SYSTEM
P: Jan Harkes
M: jaharkes@cs.cmu.edu
CYBERPRO FB DRIVER
P: Russell King
-M: rmk@arm.linux.org.uk
+M: linux@arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
W: http://www.arm.linux.org.uk/
S: Maintained
F: drivers/video/cyber2000fb.*
F: drivers/block/nbd.c
F: include/linux/nbd.h
-NETWORK DEVICE DRIVERS
-P: Jeff Garzik
-M: jgarzik@pobox.com
-L: netdev@vger.kernel.org
-T: git git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6.git
-S: Maintained
-F: drivers/net/
-
NETWORKING [GENERAL]
-P: Networking Team
-M: netdev@vger.kernel.org
+P: David S. Miller
+M: davem@davemloft.net
L: netdev@vger.kernel.org
W: http://linux-net.osdl.org/
+T: git kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git
S: Maintained
F: net/
F: include/net/
P: Takashi Iwai
M: tiwai@suse.de
L: alsa-devel@alsa-project.org (subscribers-only)
+W: http://www.alsa-project.org/
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git
+T: git git://git.alsa-project.org/alsa-kernel.git
S: Maintained
+F: Documentation/sound/
+F: include/sound/
F: sound/
SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT (ASoC)
.tmp_kallsyms* .tmp_version .tmp_vmlinux* .tmp_System.map
# Directories & files removed with 'make mrproper'
-MRPROPER_DIRS += include/config include2 usr/include
+MRPROPER_DIRS += include/config include2 usr/include include/generated
MRPROPER_FILES += .config .config.old include/asm .version .old_version \
include/linux/autoconf.h include/linux/version.h \
include/linux/utsrelease.h \
writel(32, base + VIC_PL190_DEF_VECT_ADDR);
for (i = 0; i < 32; i++) {
- unsigned int irq = irq_start + i;
-
- set_irq_chip(irq, &vic_chip);
- set_irq_chip_data(irq, base);
-
if (vic_sources & (1 << i)) {
+ unsigned int irq = irq_start + i;
+
+ set_irq_chip(irq, &vic_chip);
+ set_irq_chip_data(irq, base);
set_irq_handler(irq, handle_level_irq);
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc6
-# Fri Jun 20 16:29:34 2008
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ARCH_SUPPORTS_AOUT=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_LOCK_KERNEL=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-CONFIG_POSIX_MQUEUE=y
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
-# CONFIG_GROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
-# CONFIG_RELAY is not set
-# CONFIG_NAMESPACES is not set
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-CONFIG_EMBEDDED=y
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_KALLSYMS=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
-# CONFIG_SLOB is not set
-# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
-CONFIG_HAVE_OPROFILE=y
-# CONFIG_KPROBES is not set
-CONFIG_HAVE_KPROBES=y
-CONFIG_HAVE_KRETPROBES=y
-# CONFIG_HAVE_DMA_ATTRS is not set
-CONFIG_PROC_PAGE_MONITOR=y
-CONFIG_SLABINFO=y
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-# CONFIG_MODULE_FORCE_LOAD is not set
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_MODULE_FORCE_UNLOAD is not set
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-# CONFIG_IOSCHED_AS is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
-CONFIG_DEFAULT_NOOP=y
-CONFIG_DEFAULT_IOSCHED="noop"
-CONFIG_CLASSIC_RCU=y
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-CONFIG_ARCH_MXC=y
-# CONFIG_ARCH_ORION5X is not set
-# CONFIG_ARCH_PNX4008 is not set
-# CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM7X00A is not set
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Freescale MXC Implementations
-#
-CONFIG_ARCH_MX2=y
-# CONFIG_ARCH_MX3 is not set
-
-#
-# MX2 family CPU support
-#
-CONFIG_MACH_MX27=y
-
-#
-# MX2 Platforms
-#
-CONFIG_MACH_MX27ADS=y
-# CONFIG_MACH_PCM038 is not set
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_ARM926T=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5TJ=y
-CONFIG_CPU_PABRT_NOIFAR=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WB=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-
-#
-# Processor Features
-#
-CONFIG_ARM_THUMB=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-# CONFIG_OUTER_CACHE is not set
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-CONFIG_TICK_ONESHOT=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_PREEMPT=y
-CONFIG_HZ=100
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE=""
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-# CONFIG_VFP is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-CONFIG_PACKET_MMAP=y
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_IP_MROUTE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_CAN is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-CONFIG_MTD=y
-# CONFIG_MTD_DEBUG is not set
-# CONFIG_MTD_CONCAT is not set
-CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_REDBOOT_PARTS is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-# CONFIG_MTD_AFS_PARTS is not set
-# CONFIG_MTD_AR7_PARTS is not set
-
-#
-# User Modules And Translation Layers
-#
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLKDEVS=y
-CONFIG_MTD_BLOCK=y
-# CONFIG_FTL is not set
-# CONFIG_NFTL is not set
-# CONFIG_INFTL is not set
-# CONFIG_RFD_FTL is not set
-# CONFIG_SSFDC is not set
-# CONFIG_MTD_OOPS is not set
-
-#
-# RAM/ROM/Flash chip drivers
-#
-CONFIG_MTD_CFI=y
-# CONFIG_MTD_JEDECPROBE is not set
-CONFIG_MTD_GEN_PROBE=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_NOSWAP=y
-# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
-# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
-CONFIG_MTD_CFI_GEOMETRY=y
-# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
-CONFIG_MTD_MAP_BANK_WIDTH_2=y
-# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
-CONFIG_MTD_CFI_I1=y
-# CONFIG_MTD_CFI_I2 is not set
-# CONFIG_MTD_CFI_I4 is not set
-# CONFIG_MTD_CFI_I8 is not set
-# CONFIG_MTD_OTP is not set
-CONFIG_MTD_CFI_INTELEXT=y
-# CONFIG_MTD_CFI_AMDSTD is not set
-# CONFIG_MTD_CFI_STAA is not set
-CONFIG_MTD_CFI_UTIL=y
-# CONFIG_MTD_RAM is not set
-# CONFIG_MTD_ROM is not set
-# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_XIP is not set
-
-#
-# Mapping drivers for chip access
-#
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0x00000000
-CONFIG_MTD_PHYSMAP_LEN=0x0
-CONFIG_MTD_PHYSMAP_BANKWIDTH=2
-# CONFIG_MTD_ARM_INTEGRATOR is not set
-# CONFIG_MTD_PLATRAM is not set
-
-#
-# Self-contained MTD device drivers
-#
-# CONFIG_MTD_SLRAM is not set
-# CONFIG_MTD_PHRAM is not set
-# CONFIG_MTD_MTDRAM is not set
-# CONFIG_MTD_BLOCK2MTD is not set
-
-#
-# Disk-On-Chip Device Drivers
-#
-# CONFIG_MTD_DOC2000 is not set
-# CONFIG_MTD_DOC2001 is not set
-# CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
-# CONFIG_MTD_ONENAND is not set
-
-#
-# UBI - Unsorted block images
-#
-# CONFIG_MTD_UBI is not set
-# CONFIG_PARPORT is not set
-CONFIG_BLK_DEV=y
-# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_RAM is not set
-# CONFIG_CDROM_PKTCDVD is not set
-# CONFIG_ATA_OVER_ETH is not set
-# CONFIG_MISC_DEVICES is not set
-CONFIG_HAVE_IDE=y
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-# CONFIG_MII is not set
-# CONFIG_AX88796 is not set
-# CONFIG_SMC91X is not set
-# CONFIG_DM9000 is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_FEC_OLD is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_JOYDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-# CONFIG_TOUCHSCREEN_FUJITSU is not set
-# CONFIG_TOUCHSCREEN_GUNZE is not set
-# CONFIG_TOUCHSCREEN_ELO is not set
-# CONFIG_TOUCHSCREEN_MTOUCH is not set
-# CONFIG_TOUCHSCREEN_MK712 is not set
-# CONFIG_TOUCHSCREEN_PENMOUNT is not set
-# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
-# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
-# CONFIG_TOUCHSCREEN_UCB1400 is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-# CONFIG_VT is not set
-CONFIG_DEVKMEM=y
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-# CONFIG_SERIAL_IMX is not set
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-# CONFIG_SPI is not set
-CONFIG_HAVE_GPIO_LIB=y
-
-#
-# GPIO Support
-#
-
-#
-# I2C GPIO expanders:
-#
-
-#
-# SPI GPIO expanders:
-#
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-# CONFIG_WATCHDOG is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-# CONFIG_MFD_ASIC3 is not set
-# CONFIG_HTC_EGPIO is not set
-# CONFIG_HTC_PASIC3 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-# CONFIG_UIO is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-# CONFIG_FS_POSIX_ACL is not set
-# CONFIG_XFS_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_DNOTIFY is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_FS_DEBUG=0
-CONFIG_JFFS2_FS_WRITEBUFFER=y
-# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
-# CONFIG_JFFS2_SUMMARY is not set
-# CONFIG_JFFS2_FS_XATTR is not set
-# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
-CONFIG_JFFS2_ZLIB=y
-# CONFIG_JFFS2_LZO is not set
-CONFIG_JFFS2_RTIME=y
-# CONFIG_JFFS2_RUBIN is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-# CONFIG_NFS_V3_ACL is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
-# CONFIG_RPCSEC_GSS_KRB5 is not set
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-CONFIG_NLS=y
-CONFIG_NLS_DEFAULT="iso8859-1"
-CONFIG_NLS_CODEPAGE_437=m
-# CONFIG_NLS_CODEPAGE_737 is not set
-# CONFIG_NLS_CODEPAGE_775 is not set
-CONFIG_NLS_CODEPAGE_850=m
-# CONFIG_NLS_CODEPAGE_852 is not set
-# CONFIG_NLS_CODEPAGE_855 is not set
-# CONFIG_NLS_CODEPAGE_857 is not set
-# CONFIG_NLS_CODEPAGE_860 is not set
-# CONFIG_NLS_CODEPAGE_861 is not set
-# CONFIG_NLS_CODEPAGE_862 is not set
-# CONFIG_NLS_CODEPAGE_863 is not set
-# CONFIG_NLS_CODEPAGE_864 is not set
-# CONFIG_NLS_CODEPAGE_865 is not set
-# CONFIG_NLS_CODEPAGE_866 is not set
-# CONFIG_NLS_CODEPAGE_869 is not set
-# CONFIG_NLS_CODEPAGE_936 is not set
-# CONFIG_NLS_CODEPAGE_950 is not set
-# CONFIG_NLS_CODEPAGE_932 is not set
-# CONFIG_NLS_CODEPAGE_949 is not set
-# CONFIG_NLS_CODEPAGE_874 is not set
-# CONFIG_NLS_ISO8859_8 is not set
-# CONFIG_NLS_CODEPAGE_1250 is not set
-# CONFIG_NLS_CODEPAGE_1251 is not set
-# CONFIG_NLS_ASCII is not set
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_NLS_ISO8859_2 is not set
-# CONFIG_NLS_ISO8859_3 is not set
-# CONFIG_NLS_ISO8859_4 is not set
-# CONFIG_NLS_ISO8859_5 is not set
-# CONFIG_NLS_ISO8859_6 is not set
-# CONFIG_NLS_ISO8859_7 is not set
-# CONFIG_NLS_ISO8859_9 is not set
-# CONFIG_NLS_ISO8859_13 is not set
-# CONFIG_NLS_ISO8859_14 is not set
-CONFIG_NLS_ISO8859_15=m
-# CONFIG_NLS_KOI8_R is not set
-# CONFIG_NLS_KOI8_U is not set
-# CONFIG_NLS_UTF8 is not set
-# CONFIG_DLM is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_FRAME_WARN=1024
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_FRAME_POINTER=y
-# CONFIG_SAMPLES is not set
-# CONFIG_DEBUG_USER is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-# CONFIG_CRYPTO is not set
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-# CONFIG_GENERIC_FIND_NEXT_BIT is not set
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc6
-# Fri Jun 20 16:21:11 2008
+# Linux kernel version: 2.6.30-rc1
+# Wed Apr 8 11:11:33 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ARCH_SUPPORTS_AOUT=y
-CONFIG_ZONE_DMA=y
CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
CONFIG_GROUP_SCHED=y
CONFIG_FAIR_GROUP_SCHED=y
# CONFIG_RT_GROUP_SCHED is not set
CONFIG_USER_SCHED=y
# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
+CONFIG_AIO=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
-# CONFIG_HAVE_DMA_ATTRS is not set
-CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
-CONFIG_CLASSIC_RCU=y
+CONFIG_FREEZER=y
#
# System Type
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
CONFIG_ARCH_MXC=y
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM7X00A is not set
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_W90X900 is not set
+CONFIG_ARCH_MX1ADS=y
#
# Freescale MXC Implementations
#
+CONFIG_ARCH_MX1=y
# CONFIG_ARCH_MX2 is not set
-CONFIG_ARCH_MX3=y
+# CONFIG_ARCH_MX3 is not set
#
-# MX3 Options
+# MX1 platforms:
#
-CONFIG_MACH_MX31ADS=y
-# CONFIG_MACH_PCM037 is not set
+CONFIG_MACH_MXLADS=y
+CONFIG_MACH_SCB9328=y
+CONFIG_MXC_IRQ_PRIOR=y
+# CONFIG_MXC_PWM is not set
#
# Processor Type
#
CONFIG_CPU_32=y
-CONFIG_CPU_V6=y
-# CONFIG_CPU_32v6K is not set
-CONFIG_CPU_32v6=y
-CONFIG_CPU_ABRT_EV6=y
+CONFIG_CPU_ARM920T=y
+CONFIG_CPU_32v4T=y
+CONFIG_CPU_ABRT_EV4T=y
CONFIG_CPU_PABRT_NOIFAR=y
-CONFIG_CPU_CACHE_V6=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_TLB_V6=y
-CONFIG_CPU_HAS_ASID=y
+CONFIG_CPU_CACHE_V4WT=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y
CONFIG_ARM_THUMB=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
# CONFIG_OUTER_CACHE is not set
#
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_OABI_COMPAT=y
+CONFIG_ARCH_FLATMEM_HAS_HOLES=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
CONFIG_ALIGNMENT_TRAP=y
#
# CONFIG_KEXEC is not set
#
+# CPU Power Management
+#
+# CONFIG_CPU_IDLE is not set
+
+#
# Floating point emulation
#
#
# At least one emulation must be selected
#
-CONFIG_VFP=y
+# CONFIG_FPE_NWFPE is not set
+# CONFIG_FPE_FASTFPE is not set
#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set
#
# Power management options
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+CONFIG_PM_DEBUG=y
+# CONFIG_PM_VERBOSE is not set
+CONFIG_CAN_PM_TRACE=y
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
CONFIG_ARCH_SUSPEND_POSSIBLE=y
-
-#
-# Networking
-#
CONFIG_NET=y
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
+# CONFIG_INET_DIAG is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
#
# Network testing
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
-# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
-# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_NOSWAP=y
-# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
-# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
-CONFIG_MTD_CFI_GEOMETRY=y
-# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
-# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
-# CONFIG_MTD_CFI_I2 is not set
+CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
-# CONFIG_MTD_OTP is not set
# CONFIG_MTD_CFI_INTELEXT is not set
-CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_AMDSTD is not set
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
-CONFIG_MTD_RAM=y
+# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_XIP is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-CONFIG_MTD_NAND=y
-# CONFIG_MTD_NAND_VERIFY_WRITE is not set
-# CONFIG_MTD_NAND_ECC_SMC is not set
-# CONFIG_MTD_NAND_MUSEUM_IDS is not set
-CONFIG_MTD_NAND_IDS=y
-# CONFIG_MTD_NAND_DISKONCHIP is not set
-# CONFIG_MTD_NAND_NANDSIM is not set
-# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_NAND is not set
# CONFIG_MTD_ONENAND is not set
#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
+CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+CONFIG_SMSC_PHY=y
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_AX88796 is not set
# CONFIG_SMC91X is not set
-# CONFIG_DM9000 is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_DEBUGLEVEL=4
+# CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_GPIO is not set
+CONFIG_I2C_IMX=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
-CONFIG_HAVE_GPIO_LIB=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_GPIO_SYSFS is not set
#
-# GPIO Support
+# Memory mapped GPIO expanders:
#
#
# I2C GPIO expanders:
#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
#
# SPI GPIO expanders:
#
-# CONFIG_W1 is not set
+CONFIG_W1=y
+
+#
+# 1-wire Bus Masters
+#
+# CONFIG_W1_MASTER_DS2482 is not set
+CONFIG_W1_MASTER_MXC=y
+# CONFIG_W1_MASTER_GPIO is not set
+
+#
+# 1-wire Slaves
+#
+CONFIG_W1_SLAVE_THERM=y
+# CONFIG_W1_SLAVE_SMEM is not set
+# CONFIG_W1_SLAVE_DS2431 is not set
+# CONFIG_W1_SLAVE_DS2433 is not set
+# CONFIG_W1_SLAVE_DS2760 is not set
+# CONFIG_W1_SLAVE_BQ27000 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
-CONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
#
# Multimedia devices
#
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+# CONFIG_FB_CFB_FILLRECT is not set
+# CONFIG_FB_CFB_COPYAREA is not set
+# CONFIG_FB_CFB_IMAGEBLIT is not set
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_LOGO is not set
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
#
-# Sound
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+CONFIG_USB_GADGET_IMX=y
+CONFIG_USB_IMX=y
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+# CONFIG_USB_ZERO is not set
+CONFIG_USB_ETH=y
+CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_GADGETFS is not set
+# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_G_SERIAL is not set
+# CONFIG_USB_MIDI_GADGET is not set
+# CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
+
#
-# CONFIG_SOUND is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_MXC=y
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_NEW_LEDS is not set
CONFIG_RTC_LIB=y
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
+# CONFIG_EXT4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
+CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
# CONFIG_DNOTIFY is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_FUSE_FS is not set
#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
-CONFIG_CRAMFS=y
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
-# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
#
# Kernel hacking
#
-CONFIG_PRINTK_TIME=y
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_FRAME_POINTER=y
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_PREEMPT_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_ARM_UNWIND=y
# CONFIG_DEBUG_USER is not set
#
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_TEST is not set
#
# Block modes
#
-# CONFIG_CRYPTO_CBC is not set
+CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
# CONFIG_CRYPTO_ECB is not set
#
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
-# CONFIG_CRYPTO_MD5 is not set
+CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_DES is not set
+CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
-# CONFIG_CRYPTO_HW is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-# CONFIG_GENERIC_FIND_NEXT_BIT is not set
+CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc6
-# Fri Jun 20 16:38:36 2008
+# Linux kernel version: 2.6.30-rc1
+# Wed Apr 8 10:18:06 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ARCH_SUPPORTS_AOUT=y
-CONFIG_ZONE_DMA=y
CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
CONFIG_GROUP_SCHED=y
CONFIG_FAIR_GROUP_SCHED=y
CONFIG_RT_GROUP_SCHED=y
CONFIG_USER_SCHED=y
# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
-# CONFIG_COMPAT_BRK is not set
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
+CONFIG_AIO=y
CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_COMPAT_BRK is not set
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
+CONFIG_TRACEPOINTS=y
CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_KRETPROBES=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
-# CONFIG_HAVE_DMA_ATTRS is not set
-# CONFIG_PROC_PAGE_MONITOR is not set
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
CONFIG_BLOCK=y
# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
-CONFIG_CLASSIC_RCU=y
+CONFIG_FREEZER=y
#
# System Type
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
CONFIG_ARCH_MXC=y
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM7X00A is not set
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_W90X900 is not set
#
# Freescale MXC Implementations
#
+# CONFIG_ARCH_MX1 is not set
CONFIG_ARCH_MX2=y
# CONFIG_ARCH_MX3 is not set
-
-#
-# MX2 family CPU support
-#
+# CONFIG_MACH_MX21 is not set
CONFIG_MACH_MX27=y
#
-# MX2 Platforms
+# MX2 platforms:
#
-# CONFIG_MACH_MX27ADS is not set
+CONFIG_MACH_MX27ADS=y
CONFIG_MACH_PCM038=y
CONFIG_MACH_PCM970_BASEBOARD=y
+CONFIG_MXC_IRQ_PRIOR=y
+CONFIG_MXC_PWM=y
#
# Processor Type
# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
# CONFIG_OUTER_CACHE is not set
+CONFIG_COMMON_CLKDEV=y
#
# Bus support
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_OABI_COMPAT=y
+CONFIG_ARCH_FLATMEM_HAS_HOLES=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
CONFIG_ALIGNMENT_TRAP=y
#
# CONFIG_KEXEC is not set
#
+# CPU Power Management
+#
+# CONFIG_CPU_IDLE is not set
+
+#
# Floating point emulation
#
#
# At least one emulation must be selected
#
+CONFIG_FPE_NWFPE=y
+CONFIG_FPE_NWFPE_XP=y
+# CONFIG_FPE_FASTFPE is not set
# CONFIG_VFP is not set
#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set
#
# Power management options
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+CONFIG_PM_DEBUG=y
+# CONFIG_PM_VERBOSE is not set
+CONFIG_CAN_PM_TRACE=y
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+# CONFIG_PM_TEST_SUSPEND is not set
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
CONFIG_ARCH_SUSPEND_POSSIBLE=y
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
+CONFIG_IP_PNP_DHCP=y
# CONFIG_IP_PNP_BOOTP is not set
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
+# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0x00000000
-CONFIG_MTD_PHYSMAP_LEN=0x0
-CONFIG_MTD_PHYSMAP_BANKWIDTH=2
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_MTD_ONENAND is not set
#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
+CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_SMC91X is not set
# CONFIG_DM9000 is not set
# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
-CONFIG_FEC_OLD=y
+CONFIG_FEC=y
+# CONFIG_FEC2 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
# CONFIG_TOUCHSCREEN_PENMOUNT is not set
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
-# CONFIG_TOUCHSCREEN_UCB1400 is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
#
# Non-8250 serial port support
#
+# CONFIG_SERIAL_MAX3100 is not set
CONFIG_SERIAL_IMX=y
CONFIG_SERIAL_IMX_CONSOLE=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
-# CONFIG_I2C_CHARDEV is not set
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
#
# I2C Hardware Bus support
#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
# CONFIG_I2C_GPIO is not set
+CONFIG_I2C_IMX=y
# CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
-# CONFIG_I2C_STUB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_EEPROM_LEGACY is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCF8591 is not set
-# CONFIG_TPS65010 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=y
+# CONFIG_SPI_GPIO is not set
#
# SPI Protocol Masters
#
-# CONFIG_EEPROM_AT25 is not set
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
-CONFIG_HAVE_GPIO_LIB=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_GPIO_SYSFS is not set
#
-# GPIO Support
+# Memory mapped GPIO expanders:
#
#
# I2C GPIO expanders:
#
+# CONFIG_GPIO_MAX732X is not set
# CONFIG_GPIO_PCA953X is not set
# CONFIG_GPIO_PCF857X is not set
#
+# PCI GPIO expanders:
+#
+
+#
# SPI GPIO expanders:
#
+# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
-# CONFIG_W1 is not set
+CONFIG_W1=y
+
+#
+# 1-wire Bus Masters
+#
+# CONFIG_W1_MASTER_DS2482 is not set
+CONFIG_W1_MASTER_MXC=y
+# CONFIG_W1_MASTER_GPIO is not set
+
+#
+# 1-wire Slaves
+#
+CONFIG_W1_SLAVE_THERM=y
+# CONFIG_W1_SLAVE_SMEM is not set
+# CONFIG_W1_SLAVE_DS2431 is not set
+# CONFIG_W1_SLAVE_DS2433 is not set
+# CONFIG_W1_SLAVE_DS2760 is not set
+# CONFIG_W1_SLAVE_BQ27000 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
-CONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
#
# Multimedia devices
#
# CONFIG_MEDIA_ATTACH is not set
CONFIG_MEDIA_TUNER=y
-# CONFIG_MEDIA_TUNER_CUSTOMIZE is not set
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
CONFIG_MEDIA_TUNER_SIMPLE=y
CONFIG_MEDIA_TUNER_TDA8290=y
CONFIG_MEDIA_TUNER_TDA9887=y
CONFIG_MEDIA_TUNER_MT20XX=y
CONFIG_MEDIA_TUNER_XC2028=y
CONFIG_MEDIA_TUNER_XC5000=y
+CONFIG_MEDIA_TUNER_MC44S803=y
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
+# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
# CONFIG_VIDEO_VIVI is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
-# CONFIG_TUNER_3036 is not set
# CONFIG_SOC_CAMERA is not set
# CONFIG_RADIO_ADAPTERS is not set
# CONFIG_DAB is not set
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
-# CONFIG_FB_CFB_FILLRECT is not set
-# CONFIG_FB_CFB_COPYAREA is not set
-# CONFIG_FB_CFB_IMAGEBLIT is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
#
# Frame buffer hardware drivers
#
+CONFIG_FB_IMX=y
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
# CONFIG_LOGO is not set
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_MXC=y
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_NEW_LEDS is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
#
# SPI RTC drivers
#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
# CONFIG_RTC_DRV_MAX6902 is not set
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
+# CONFIG_EXT4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
+CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY is not set
# CONFIG_QUOTA is not set
# CONFIG_FUSE_FS is not set
#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
+# CONFIG_PROC_PAGE_MONITOR is not set
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
+CONFIG_STACKTRACE=y
# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_FRAME_POINTER=y
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_NOP_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_RING_BUFFER=y
+CONFIG_TRACING=y
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_PREEMPT_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_ARM_UNWIND=y
# CONFIG_DEBUG_USER is not set
#
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
# CONFIG_CRYPTO is not set
+CONFIG_BINARY_PRINTF=y
#
# Library routines
#
CONFIG_BITREVERSE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-# CONFIG_GENERIC_FIND_NEXT_BIT is not set
+CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc5
-# Fri Jun 13 14:23:39 2008
+# Linux kernel version: 2.6.30-rc1
+# Wed Apr 8 11:06:37 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_GENERIC_GPIO is not set
-# CONFIG_GENERIC_TIME is not set
-# CONFIG_GENERIC_CLOCKEVENTS is not set
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_MMU=y
# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ARCH_SUPPORTS_AOUT=y
-CONFIG_ZONE_DMA=y
CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
# CONFIG_CGROUPS is not set
-# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
+CONFIG_AIO=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
-# CONFIG_HAVE_DMA_ATTRS is not set
-CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
-CONFIG_CLASSIC_RCU=y
+CONFIG_FREEZER=y
#
# System Type
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
CONFIG_ARCH_MXC=y
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM7X00A is not set
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_W90X900 is not set
#
# Freescale MXC Implementations
#
+# CONFIG_ARCH_MX1 is not set
+# CONFIG_ARCH_MX2 is not set
CONFIG_ARCH_MX3=y
+CONFIG_ARCH_MX31=y
#
-# MX3 Options
+# MX3 platforms:
#
-# CONFIG_MACH_MX31ADS is not set
+CONFIG_MACH_MX31ADS=y
+CONFIG_MACH_MX31ADS_WM1133_EV1=y
+CONFIG_MACH_PCM037=y
CONFIG_MACH_MX31LITE=y
+CONFIG_MACH_MX31_3DS=y
+CONFIG_MACH_MX31MOBOARD=y
+CONFIG_MACH_QONG=y
+CONFIG_MXC_IRQ_PRIOR=y
+CONFIG_MXC_PWM=y
#
# Processor Type
#
CONFIG_CPU_32=y
CONFIG_CPU_V6=y
-# CONFIG_CPU_32v6K is not set
+CONFIG_CPU_32v6K=y
CONFIG_CPU_32v6=y
CONFIG_CPU_ABRT_EV6=y
CONFIG_CPU_PABRT_NOIFAR=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
+CONFIG_OUTER_CACHE=y
+CONFIG_CACHE_L2X0=y
+CONFIG_COMMON_CLKDEV=y
#
# Bus support
#
# CONFIG_PCI_SYSCALL is not set
# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_PCCARD=m
-# CONFIG_PCMCIA_DEBUG is not set
-# CONFIG_PCMCIA is not set
-
-#
-# PC-card bridges
-#
+# CONFIG_PCCARD is not set
#
# Kernel Features
#
-# CONFIG_TICK_ONESHOT is not set
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_PREEMPT=y
-# CONFIG_NO_IDLE_HZ is not set
CONFIG_HZ=100
CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_OABI_COMPAT=y
+CONFIG_ARCH_FLATMEM_HAS_HOLES=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
CONFIG_ALIGNMENT_TRAP=y
#
# CONFIG_KEXEC is not set
#
+# CPU Power Management
+#
+# CONFIG_CPU_IDLE is not set
+
+#
# Floating point emulation
#
#
# At least one emulation must be selected
#
+# CONFIG_FPE_NWFPE is not set
+# CONFIG_FPE_FASTFPE is not set
CONFIG_VFP=y
#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
-CONFIG_BINFMT_AOUT=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set
#
# Power management options
#
CONFIG_PM=y
-# CONFIG_PM_DEBUG is not set
-# CONFIG_SUSPEND is not set
+CONFIG_PM_DEBUG=y
+# CONFIG_PM_VERBOSE is not set
+CONFIG_CAN_PM_TRACE=y
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
# CONFIG_APM_EMULATION is not set
CONFIG_ARCH_SUSPEND_POSSIBLE=y
-
-#
-# Networking
-#
CONFIG_NET=y
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
+# CONFIG_INET_DIAG is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
#
# Network testing
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
-# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
-# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_NOSWAP=y
-# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
-# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
-CONFIG_MTD_CFI_GEOMETRY=y
-# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
-# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
-# CONFIG_MTD_CFI_I2 is not set
+CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
-# CONFIG_MTD_OTP is not set
# CONFIG_MTD_CFI_INTELEXT is not set
-CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_AMDSTD is not set
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
-CONFIG_MTD_RAM=y
+# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_XIP is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-CONFIG_MTD_NAND=y
-# CONFIG_MTD_NAND_VERIFY_WRITE is not set
-# CONFIG_MTD_NAND_ECC_SMC is not set
-# CONFIG_MTD_NAND_MUSEUM_IDS is not set
-CONFIG_MTD_NAND_IDS=y
-# CONFIG_MTD_NAND_DISKONCHIP is not set
-# CONFIG_MTD_NAND_NANDSIM is not set
-# CONFIG_MTD_NAND_PLATFORM is not set
-# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_NAND is not set
# CONFIG_MTD_ONENAND is not set
#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
-CONFIG_SCSI=y
-CONFIG_SCSI_DMA=y
-# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
# CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
-
-#
-# SCSI support type (disk, tape, CD-ROM)
-#
-CONFIG_BLK_DEV_SD=y
-# CONFIG_CHR_DEV_ST is not set
-# CONFIG_CHR_DEV_OSST is not set
-# CONFIG_BLK_DEV_SR is not set
-# CONFIG_CHR_DEV_SG is not set
-# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
-CONFIG_SCSI_MULTI_LUN=y
-# CONFIG_SCSI_CONSTANTS is not set
-# CONFIG_SCSI_LOGGING is not set
-# CONFIG_SCSI_SCAN_ASYNC is not set
-CONFIG_SCSI_WAIT_SCAN=m
-
-#
-# SCSI Transports
-#
-# CONFIG_SCSI_SPI_ATTRS is not set
-# CONFIG_SCSI_FC_ATTRS is not set
-# CONFIG_SCSI_ISCSI_ATTRS is not set
-# CONFIG_SCSI_SAS_LIBSAS is not set
-# CONFIG_SCSI_SRP_ATTRS is not set
-CONFIG_SCSI_LOWLEVEL=y
-# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_DEBUG is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
+CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+CONFIG_SMSC_PHY=y
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_AX88796 is not set
# CONFIG_SMC91X is not set
# CONFIG_DM9000 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+CONFIG_SMSC911X=y
+# CONFIG_DNET is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
+CONFIG_CS89x0=y
+CONFIG_CS89x0_NONISA_IRQ=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
#
-# USB Network Adapters
+# Enable WiMAX (Networking options) to see the WiMAX drivers
#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
# Input device support
#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_JOYDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-CONFIG_INPUT_KEYBOARD=y
-# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
-# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
-# CONFIG_KEYBOARD_NEWTON is not set
-# CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-# CONFIG_TOUCHSCREEN_FUJITSU is not set
-# CONFIG_TOUCHSCREEN_GUNZE is not set
-# CONFIG_TOUCHSCREEN_ELO is not set
-# CONFIG_TOUCHSCREEN_MTOUCH is not set
-# CONFIG_TOUCHSCREEN_MK712 is not set
-# CONFIG_TOUCHSCREEN_PENMOUNT is not set
-# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
-# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
-# CONFIG_TOUCHSCREEN_UCB1400 is not set
-# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
-# CONFIG_INPUT_MISC is not set
+# CONFIG_INPUT is not set
#
# Hardware I/O ports
#
# Character devices
#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_VT is not set
CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Non-8250 serial port support
#
+CONFIG_SERIAL_IMX=y
+CONFIG_SERIAL_IMX_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
-CONFIG_HW_RANDOM=y
-# CONFIG_NVRAM is not set
+# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_GPIO is not set
+CONFIG_I2C_IMX=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_GPIO_SYSFS is not set
#
-# Watchdog Device Drivers
+# Memory mapped GPIO expanders:
#
-# CONFIG_SOFT_WATCHDOG is not set
#
-# USB-based Watchdog Cards
+# I2C GPIO expanders:
#
-# CONFIG_USBPCWATCHDOG is not set
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
#
-# Sonics Silicon Backplane
+# PCI GPIO expanders:
#
+
+#
+# SPI GPIO expanders:
+#
+CONFIG_W1=y
+
+#
+# 1-wire Bus Masters
+#
+# CONFIG_W1_MASTER_DS2482 is not set
+CONFIG_W1_MASTER_MXC=y
+# CONFIG_W1_MASTER_GPIO is not set
+
+#
+# 1-wire Slaves
+#
+CONFIG_W1_SLAVE_THERM=y
+# CONFIG_W1_SLAVE_SMEM is not set
+# CONFIG_W1_SLAVE_DS2431 is not set
+# CONFIG_W1_SLAVE_DS2433 is not set
+# CONFIG_W1_SLAVE_DS2760 is not set
+# CONFIG_W1_SLAVE_BQ27000 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+CONFIG_MFD_WM8350=y
+CONFIG_MFD_WM8350_CONFIG_MODE_0=y
+CONFIG_MFD_WM8352_CONFIG_MODE_0=y
+CONFIG_MFD_WM8350_I2C=y
+# CONFIG_MFD_PCF50633 is not set
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=y
CONFIG_VIDEO_V4L2_COMMON=y
-CONFIG_VIDEO_ALLOW_V4L1=y
+# CONFIG_VIDEO_ALLOW_V4L1 is not set
CONFIG_VIDEO_V4L1_COMPAT=y
# CONFIG_DVB_CORE is not set
CONFIG_VIDEO_MEDIA=y
# Multimedia drivers
#
# CONFIG_MEDIA_ATTACH is not set
+CONFIG_MEDIA_TUNER=y
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
+CONFIG_MEDIA_TUNER_SIMPLE=y
+CONFIG_MEDIA_TUNER_TDA8290=y
+CONFIG_MEDIA_TUNER_TDA9887=y
+CONFIG_MEDIA_TUNER_TEA5761=y
+CONFIG_MEDIA_TUNER_TEA5767=y
+CONFIG_MEDIA_TUNER_MT20XX=y
+CONFIG_MEDIA_TUNER_XC2028=y
+CONFIG_MEDIA_TUNER_XC5000=y
+CONFIG_MEDIA_TUNER_MC44S803=y
CONFIG_VIDEO_V4L2=y
-CONFIG_VIDEO_V4L1=y
+CONFIG_VIDEOBUF_GEN=y
+CONFIG_VIDEOBUF_DMA_CONTIG=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
+# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
# CONFIG_VIDEO_VIVI is not set
-# CONFIG_VIDEO_CPIA is not set
-# CONFIG_VIDEO_CPIA2 is not set
-CONFIG_V4L_USB_DRIVERS=y
-# CONFIG_USB_VICAM is not set
-# CONFIG_USB_IBMCAM is not set
-# CONFIG_USB_KONICAWC is not set
-# CONFIG_USB_QUICKCAM_MESSENGER is not set
-# CONFIG_USB_ET61X251 is not set
-# CONFIG_USB_OV511 is not set
-# CONFIG_USB_SE401 is not set
-# CONFIG_USB_SN9C102 is not set
-# CONFIG_USB_STV680 is not set
-# CONFIG_USB_ZC0301 is not set
-# CONFIG_USB_PWC is not set
-# CONFIG_USB_ZR364XX is not set
-# CONFIG_USB_STKWEBCAM is not set
-# CONFIG_SOC_CAMERA is not set
-CONFIG_RADIO_ADAPTERS=y
-# CONFIG_USB_DSBR is not set
-# CONFIG_USB_SI470X is not set
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_VIDEO_SAA5246A is not set
+# CONFIG_VIDEO_SAA5249 is not set
+CONFIG_SOC_CAMERA=y
+CONFIG_SOC_CAMERA_MT9M001=y
+CONFIG_SOC_CAMERA_MT9M111=y
+CONFIG_SOC_CAMERA_MT9T031=y
+CONFIG_SOC_CAMERA_MT9V022=y
+CONFIG_SOC_CAMERA_TW9910=y
+# CONFIG_SOC_CAMERA_PLATFORM is not set
+# CONFIG_SOC_CAMERA_OV772X is not set
+CONFIG_VIDEO_MX3=y
+# CONFIG_RADIO_ADAPTERS is not set
+# CONFIG_DAB is not set
#
# Graphics support
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
-# CONFIG_FB_CFB_FILLRECT is not set
-# CONFIG_FB_CFB_COPYAREA is not set
-# CONFIG_FB_CFB_IMAGEBLIT is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
#
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+CONFIG_FB_MX3=y
+# CONFIG_FB_BROADSHEET is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-# CONFIG_FONTS is not set
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
+# CONFIG_LOGO is not set
# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB_SUPPORT=y
-CONFIG_USB_ARCH_HAS_HCD=y
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-# CONFIG_USB_ARCH_HAS_EHCI is not set
-CONFIG_USB=y
-# CONFIG_USB_DEBUG is not set
-# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
#
-# Miscellaneous USB options
+# MMC/SD/SDIO Card Drivers
#
-# CONFIG_USB_DEVICEFS is not set
-CONFIG_USB_DEVICE_CLASS=y
-# CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_SUSPEND is not set
-# CONFIG_USB_OTG is not set
-# CONFIG_USB_OTG_WHITELIST is not set
-# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
#
-# USB Host Controller Drivers
+# MMC/SD/SDIO Host Controller Drivers
#
-# CONFIG_USB_C67X00_HCD is not set
-# CONFIG_USB_ISP116X_HCD is not set
-# CONFIG_USB_ISP1760_HCD is not set
-# CONFIG_USB_SL811_HCD is not set
-# CONFIG_USB_R8A66597_HCD is not set
-
-#
-# USB Device Class drivers
-#
-# CONFIG_USB_ACM is not set
-# CONFIG_USB_PRINTER is not set
-# CONFIG_USB_WDM is not set
-
-#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-#
-
-#
-# may also be needed; see USB_STORAGE Help for more information
-#
-# CONFIG_USB_STORAGE is not set
-# CONFIG_USB_LIBUSUAL is not set
-
-#
-# USB Imaging devices
-#
-# CONFIG_USB_MDC800 is not set
-# CONFIG_USB_MICROTEK is not set
-CONFIG_USB_MON=y
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_MXC=y
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_NEW_LEDS is not set
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+CONFIG_DMADEVICES=y
#
-# USB port drivers
+# DMA Devices
#
-# CONFIG_USB_SERIAL is not set
+CONFIG_MX3_IPU=y
+CONFIG_MX3_IPU_IRQS=4
+CONFIG_DMA_ENGINE=y
#
-# USB Miscellaneous drivers
+# DMA Clients
#
-# CONFIG_USB_EMI62 is not set
-# CONFIG_USB_EMI26 is not set
-# CONFIG_USB_ADUTUX is not set
-# CONFIG_USB_AUERSWALD is not set
-# CONFIG_USB_RIO500 is not set
-# CONFIG_USB_LEGOTOWER is not set
-# CONFIG_USB_LCD is not set
-# CONFIG_USB_BERRY_CHARGE is not set
-# CONFIG_USB_LED is not set
-# CONFIG_USB_CYPRESS_CY7C63 is not set
-# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGET is not set
-# CONFIG_USB_IDMOUSE is not set
-# CONFIG_USB_FTDI_ELAN is not set
-# CONFIG_USB_APPLEDISPLAY is not set
-# CONFIG_USB_LD is not set
-# CONFIG_USB_TRANCEVIBRATOR is not set
-# CONFIG_USB_IOWARRIOR is not set
-# CONFIG_USB_ISIGHTFW is not set
-# CONFIG_USB_GADGET is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
+# CONFIG_NET_DMA is not set
+# CONFIG_ASYNC_TX_DMA is not set
+# CONFIG_DMATEST is not set
+# CONFIG_AUXDISPLAY is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+CONFIG_REGULATOR_WM8350=y
# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
+# CONFIG_EXT4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
+CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
# CONFIG_DNOTIFY is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_FUSE_FS is not set
#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
-CONFIG_CRAMFS=y
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
-# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
#
# Kernel hacking
#
-CONFIG_PRINTK_TIME=y
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_OBJECTS is not set
-# CONFIG_DEBUG_SLAB is not set
-CONFIG_DEBUG_PREEMPT=y
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_LOCK_ALLOC is not set
-# CONFIG_PROVE_LOCKING is not set
-# CONFIG_LOCK_STAT is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_WRITECOUNT is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-CONFIG_FRAME_POINTER=y
-# CONFIG_BOOT_PRINTK_DELAY is not set
-# CONFIG_RCU_TORTURE_TEST is not set
-# CONFIG_BACKTRACE_SELF_TEST is not set
-# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_PREEMPT_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_ARM_UNWIND=y
# CONFIG_DEBUG_USER is not set
-CONFIG_DEBUG_ERRORS=y
-# CONFIG_DEBUG_STACK_USAGE is not set
-CONFIG_DEBUG_LL=y
-# CONFIG_DEBUG_ICEDCC is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_TEST is not set
#
# Block modes
#
-# CONFIG_CRYPTO_CBC is not set
+CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
# CONFIG_CRYPTO_ECB is not set
#
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
-# CONFIG_CRYPTO_MD5 is not set
+CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_DES is not set
+CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-# CONFIG_GENERIC_FIND_NEXT_BIT is not set
-CONFIG_CRC_CCITT=m
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc6
-# Wed Jun 25 11:52:42 2008
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ARCH_SUPPORTS_AOUT=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_LOCK_KERNEL=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_AUDIT is not set
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
-CONFIG_GROUP_SCHED=y
-CONFIG_FAIR_GROUP_SCHED=y
-# CONFIG_RT_GROUP_SCHED is not set
-CONFIG_USER_SCHED=y
-# CONFIG_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
-# CONFIG_RELAY is not set
-# CONFIG_NAMESPACES is not set
-# CONFIG_BLK_DEV_INITRD is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL=y
-CONFIG_EMBEDDED=y
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
-# CONFIG_SLOB is not set
-# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
-CONFIG_HAVE_OPROFILE=y
-# CONFIG_KPROBES is not set
-CONFIG_HAVE_KPROBES=y
-CONFIG_HAVE_KRETPROBES=y
-# CONFIG_HAVE_DMA_ATTRS is not set
-CONFIG_PROC_PAGE_MONITOR=y
-CONFIG_SLABINFO=y
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-# CONFIG_MODULE_FORCE_LOAD is not set
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-CONFIG_CLASSIC_RCU=y
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-CONFIG_ARCH_MXC=y
-# CONFIG_ARCH_ORION5X is not set
-# CONFIG_ARCH_PNX4008 is not set
-# CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM7X00A is not set
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Freescale MXC Implementations
-#
-CONFIG_ARCH_MX3=y
-
-#
-# MX3 Options
-#
-# CONFIG_MACH_MX31ADS is not set
-CONFIG_MACH_PCM037=y
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_V6=y
-# CONFIG_CPU_32v6K is not set
-CONFIG_CPU_32v6=y
-CONFIG_CPU_ABRT_EV6=y
-CONFIG_CPU_PABRT_NOIFAR=y
-CONFIG_CPU_CACHE_V6=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_TLB_V6=y
-CONFIG_CPU_HAS_ASID=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-
-#
-# Processor Features
-#
-CONFIG_ARM_THUMB=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-CONFIG_TICK_ONESHOT=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_PREEMPT=y
-CONFIG_HZ=100
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="noinitrd console=ttymxc0,115200 root=/dev/mtdblock2 rw ip=off"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_VFP=y
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_CAN is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-CONFIG_MTD=y
-# CONFIG_MTD_DEBUG is not set
-# CONFIG_MTD_CONCAT is not set
-CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_REDBOOT_PARTS is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-# CONFIG_MTD_AFS_PARTS is not set
-# CONFIG_MTD_AR7_PARTS is not set
-
-#
-# User Modules And Translation Layers
-#
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLKDEVS=y
-CONFIG_MTD_BLOCK=y
-# CONFIG_FTL is not set
-# CONFIG_NFTL is not set
-# CONFIG_INFTL is not set
-# CONFIG_RFD_FTL is not set
-# CONFIG_SSFDC is not set
-# CONFIG_MTD_OOPS is not set
-
-#
-# RAM/ROM/Flash chip drivers
-#
-CONFIG_MTD_CFI=y
-# CONFIG_MTD_JEDECPROBE is not set
-CONFIG_MTD_GEN_PROBE=y
-# CONFIG_MTD_CFI_ADV_OPTIONS is not set
-# CONFIG_MTD_CFI_NOSWAP is not set
-# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
-# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
-CONFIG_MTD_MAP_BANK_WIDTH_1=y
-CONFIG_MTD_MAP_BANK_WIDTH_2=y
-CONFIG_MTD_MAP_BANK_WIDTH_4=y
-# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
-CONFIG_MTD_CFI_I1=y
-CONFIG_MTD_CFI_I2=y
-# CONFIG_MTD_CFI_I4 is not set
-# CONFIG_MTD_CFI_I8 is not set
-# CONFIG_MTD_CFI_INTELEXT is not set
-# CONFIG_MTD_CFI_AMDSTD is not set
-# CONFIG_MTD_CFI_STAA is not set
-# CONFIG_MTD_RAM is not set
-# CONFIG_MTD_ROM is not set
-# CONFIG_MTD_ABSENT is not set
-
-#
-# Mapping drivers for chip access
-#
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0x0
-CONFIG_MTD_PHYSMAP_LEN=0
-CONFIG_MTD_PHYSMAP_BANKWIDTH=2
-# CONFIG_MTD_ARM_INTEGRATOR is not set
-# CONFIG_MTD_PLATRAM is not set
-
-#
-# Self-contained MTD device drivers
-#
-# CONFIG_MTD_SLRAM is not set
-# CONFIG_MTD_PHRAM is not set
-# CONFIG_MTD_MTDRAM is not set
-# CONFIG_MTD_BLOCK2MTD is not set
-
-#
-# Disk-On-Chip Device Drivers
-#
-# CONFIG_MTD_DOC2000 is not set
-# CONFIG_MTD_DOC2001 is not set
-# CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
-# CONFIG_MTD_ONENAND is not set
-
-#
-# UBI - Unsorted block images
-#
-# CONFIG_MTD_UBI is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-CONFIG_HAVE_IDE=y
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-CONFIG_PHYLIB=y
-
-#
-# MII PHY device drivers
-#
-# CONFIG_MARVELL_PHY is not set
-# CONFIG_DAVICOM_PHY is not set
-# CONFIG_QSEMI_PHY is not set
-# CONFIG_LXT_PHY is not set
-# CONFIG_CICADA_PHY is not set
-# CONFIG_VITESSE_PHY is not set
-CONFIG_SMSC_PHY=y
-# CONFIG_BROADCOM_PHY is not set
-# CONFIG_ICPLUS_PHY is not set
-# CONFIG_REALTEK_PHY is not set
-# CONFIG_NATIONAL_PHY is not set
-# CONFIG_STE10XP is not set
-# CONFIG_LSI_ET1011C_PHY is not set
-# CONFIG_FIXED_PHY is not set
-# CONFIG_MDIO_BITBANG is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-CONFIG_SMSC911X=y
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-# CONFIG_INPUT is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-# CONFIG_VT is not set
-CONFIG_DEVKMEM=y
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_IMX=y
-CONFIG_SERIAL_IMX_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-# CONFIG_SPI is not set
-CONFIG_HAVE_GPIO_LIB=y
-
-#
-# GPIO Support
-#
-
-#
-# I2C GPIO expanders:
-#
-
-#
-# SPI GPIO expanders:
-#
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-# CONFIG_WATCHDOG is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-# CONFIG_MFD_ASIC3 is not set
-# CONFIG_HTC_EGPIO is not set
-# CONFIG_HTC_PASIC3 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-# CONFIG_UIO is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-# CONFIG_FS_POSIX_ACL is not set
-# CONFIG_XFS_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_DNOTIFY is not set
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-# CONFIG_QUOTA is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_FS_DEBUG=0
-CONFIG_JFFS2_FS_WRITEBUFFER=y
-# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
-# CONFIG_JFFS2_SUMMARY is not set
-# CONFIG_JFFS2_FS_XATTR is not set
-# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
-CONFIG_JFFS2_ZLIB=y
-# CONFIG_JFFS2_LZO is not set
-CONFIG_JFFS2_RTIME=y
-# CONFIG_JFFS2_RUBIN is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
-# CONFIG_RPCSEC_GSS_KRB5 is not set
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_FRAME_WARN=1024
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_FRAME_POINTER=y
-# CONFIG_SAMPLES is not set
-# CONFIG_DEBUG_USER is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-# CONFIG_CRYPTO is not set
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-# CONFIG_GENERIC_FIND_NEXT_BIT is not set
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc8
-# Mon Jul 7 16:59:23 2008
+# Linux kernel version: 2.6.30-rc2
#
CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
# CONFIG_GENERIC_TIME is not set
CONFIG_NO_IOPORT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ARCH_SUPPORTS_AOUT=y
-CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=m
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_CGROUPS is not set
# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
+CONFIG_AIO=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
-# CONFIG_HAVE_DMA_ATTRS is not set
-CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_HAVE_CLK=y
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
-CONFIG_CLASSIC_RCU=y
+CONFIG_FREEZER=y
#
# System Type
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
# CONFIG_ARCH_MXC is not set
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
CONFIG_ARCH_S3C2410=y
+# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM7X00A is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_W90X900 is not set
CONFIG_PLAT_S3C24XX=y
+CONFIG_S3C2410_CLOCK=y
+CONFIG_S3C24XX_DCLK=y
CONFIG_CPU_S3C244X=y
-# CONFIG_S3C24XX_PWM is not set
+CONFIG_S3C24XX_PWM=y
+CONFIG_S3C24XX_GPIO_EXTRA=128
+CONFIG_S3C24XX_GPIO_EXTRA64=y
+CONFIG_S3C24XX_GPIO_EXTRA128=y
CONFIG_PM_SIMTEC=y
CONFIG_S3C2410_DMA=y
# CONFIG_S3C2410_DMA_DEBUG is not set
+CONFIG_S3C24XX_ADC=y
CONFIG_MACH_SMDK=y
CONFIG_PLAT_S3C=y
CONFIG_CPU_LLSERIAL_S3C2410=y
# Boot options
#
# CONFIG_S3C_BOOT_WATCHDOG is not set
-# CONFIG_S3C_BOOT_ERROR_RESET is not set
+CONFIG_S3C_BOOT_ERROR_RESET=y
+CONFIG_S3C_BOOT_UART_FORCE_FIFO=y
#
# Power management
# CONFIG_S3C2410_PM_DEBUG is not set
# CONFIG_S3C2410_PM_CHECK is not set
CONFIG_S3C_LOWLEVEL_UART_PORT=0
+CONFIG_S3C_GPIO_SPACE=0
+CONFIG_S3C_DEV_HSMMC=y
#
# S3C2400 Machines
CONFIG_CPU_S3C2410_DMA=y
CONFIG_S3C2410_PM=y
CONFIG_S3C2410_GPIO=y
-CONFIG_S3C2410_CLOCK=y
CONFIG_SIMTEC_NOR=y
CONFIG_MACH_BAST_IDE=y
CONFIG_MACH_OTOM=y
CONFIG_MACH_AML_M5900=y
CONFIG_BAST_PC104_IRQ=y
-# CONFIG_MACH_TCT_HAMMER is not set
+CONFIG_MACH_TCT_HAMMER=y
CONFIG_MACH_VR1000=y
CONFIG_MACH_QT2410=y
CONFIG_CPU_S3C2412=y
#
# S3C2412 Machines
#
-# CONFIG_MACH_JIVE is not set
+CONFIG_MACH_JIVE=y
+# CONFIG_MACH_JIVE_SHOW_BOOTLOADER is not set
CONFIG_MACH_SMDK2413=y
CONFIG_MACH_S3C2413=y
-# CONFIG_MACH_SMDK2412 is not set
+CONFIG_MACH_SMDK2412=y
CONFIG_MACH_VSTMS=y
CONFIG_CPU_S3C2440=y
CONFIG_S3C2440_DMA=y
CONFIG_ARCH_S3C2440=y
CONFIG_MACH_NEXCODER_2440=y
CONFIG_SMDK2440_CPU2440=y
-# CONFIG_MACH_AT2440EVB is not set
+CONFIG_MACH_AT2440EVB=y
CONFIG_CPU_S3C2442=y
#
#
# Kernel Features
#
-# CONFIG_TICK_ONESHOT is not set
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
# CONFIG_PREEMPT is not set
CONFIG_HZ=200
# CONFIG_AEABI is not set
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_ARCH_FLATMEM_HAS_HOLES=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
CONFIG_ALIGNMENT_TRAP=y
#
# CONFIG_KEXEC is not set
#
+# CPU Power Management
+#
+# CONFIG_CPU_IDLE is not set
+
+#
# Floating point emulation
#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
CONFIG_BINFMT_AOUT=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_ARTHUR is not set
CONFIG_SUSPEND_FREEZER=y
CONFIG_APM_EMULATION=m
CONFIG_ARCH_SUSPEND_POSSIBLE=y
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
+CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
-# CONFIG_NET_KEY is not set
+CONFIG_XFRM_IPCOMP=m
+CONFIG_NET_KEY=m
+# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
+CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE=m
+# CONFIG_NET_IPGRE_BROADCAST is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_CONG_BIC=m
CONFIG_TCP_CONG_CUBIC=y
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+CONFIG_TCP_CONG_HSTCP=m
+CONFIG_TCP_CONG_HYBLA=m
+CONFIG_TCP_CONG_VEGAS=m
+CONFIG_TCP_CONG_SCALABLE=m
+CONFIG_TCP_CONG_LP=m
+CONFIG_TCP_CONG_VENO=m
+CONFIG_TCP_CONG_YEAH=m
+CONFIG_TCP_CONG_ILLINOIS=m
+# CONFIG_DEFAULT_BIC is not set
+CONFIG_DEFAULT_CUBIC=y
+# CONFIG_DEFAULT_HTCP is not set
+# CONFIG_DEFAULT_VEGAS is not set
+# CONFIG_DEFAULT_WESTWOOD is not set
+# CONFIG_DEFAULT_RENO is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
CONFIG_IPV6=m
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_IPV6_MROUTE is not set
# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
+
+#
+# Core Netfilter Configuration
+#
+CONFIG_NETFILTER_NETLINK=m
+CONFIG_NETFILTER_NETLINK_QUEUE=m
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CT_ACCT=y
+CONFIG_NF_CONNTRACK_MARK=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CT_PROTO_DCCP=m
+CONFIG_NF_CT_PROTO_GRE=m
+CONFIG_NF_CT_PROTO_SCTP=m
+CONFIG_NF_CT_PROTO_UDPLITE=m
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+# CONFIG_NETFILTER_TPROXY is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
+CONFIG_NETFILTER_XT_TARGET_HL=m
+CONFIG_NETFILTER_XT_TARGET_LED=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+# CONFIG_NETFILTER_XT_TARGET_NOTRACK is not set
+CONFIG_NETFILTER_XT_TARGET_RATEEST=m
+# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
+CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_HL=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_VS=m
+# CONFIG_IP_VS_IPV6 is not set
+# CONFIG_IP_VS_DEBUG is not set
+CONFIG_IP_VS_TAB_BITS=12
+
+#
+# IPVS transport protocol load balancing support
+#
+# CONFIG_IP_VS_PROTO_TCP is not set
+# CONFIG_IP_VS_PROTO_UDP is not set
+# CONFIG_IP_VS_PROTO_ESP is not set
+# CONFIG_IP_VS_PROTO_AH is not set
+
+#
+# IPVS scheduler
+#
+# CONFIG_IP_VS_RR is not set
+# CONFIG_IP_VS_WRR is not set
+# CONFIG_IP_VS_LC is not set
+# CONFIG_IP_VS_WLC is not set
+# CONFIG_IP_VS_LBLC is not set
+# CONFIG_IP_VS_LBLCR is not set
+# CONFIG_IP_VS_DH is not set
+# CONFIG_IP_VS_SH is not set
+# CONFIG_IP_VS_SED is not set
+# CONFIG_IP_VS_NQ is not set
+
+#
+# IPVS application helper
+#
+
+#
+# IP: Netfilter Configuration
+#
+CONFIG_NF_DEFRAG_IPV4=m
+CONFIG_NF_CONNTRACK_IPV4=m
+CONFIG_NF_CONNTRACK_PROC_COMPAT=y
+CONFIG_IP_NF_QUEUE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_NF_NAT=m
+CONFIG_NF_NAT_NEEDED=y
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_TARGET_NETMAP=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
+CONFIG_NF_NAT_SNMP_BASIC=m
+CONFIG_NF_NAT_PROTO_DCCP=m
+CONFIG_NF_NAT_PROTO_GRE=m
+CONFIG_NF_NAT_PROTO_UDPLITE=m
+CONFIG_NF_NAT_PROTO_SCTP=m
+CONFIG_NF_NAT_FTP=m
+CONFIG_NF_NAT_IRC=m
+CONFIG_NF_NAT_TFTP=m
+CONFIG_NF_NAT_AMANDA=m
+CONFIG_NF_NAT_PPTP=m
+CONFIG_NF_NAT_H323=m
+CONFIG_NF_NAT_SIP=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+
+#
+# IPv6: Netfilter Configuration
+#
+CONFIG_NF_CONNTRACK_IPV6=m
+CONFIG_IP6_NF_QUEUE=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_TARGET_LOG=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
# CONFIG_NET_SCHED is not set
-CONFIG_NET_SCH_FIFO=y
+CONFIG_NET_CLS_ROUTE=y
+# CONFIG_DCB is not set
#
# Network testing
#
# Bluetooth device drivers
#
-CONFIG_BT_HCIUSB=m
-CONFIG_BT_HCIUSB_SCO=y
+# CONFIG_BT_HCIBTUSB is not set
+# CONFIG_BT_HCIBTSDIO is not set
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIVHCI=m
# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
+CONFIG_WIRELESS=y
CONFIG_CFG80211=m
-CONFIG_NL80211=y
+# CONFIG_CFG80211_REG_DEBUG is not set
+# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
+# CONFIG_LIB80211 is not set
CONFIG_MAC80211=m
#
# Rate control algorithm selection
#
-CONFIG_MAC80211_RC_DEFAULT_PID=y
-# CONFIG_MAC80211_RC_DEFAULT_NONE is not set
-
-#
-# Selecting 'y' for an algorithm will
-#
-
-#
-# build the algorithm into mac80211.
-#
-CONFIG_MAC80211_RC_DEFAULT="pid"
-CONFIG_MAC80211_RC_PID=y
+CONFIG_MAC80211_RC_MINSTREL=y
+# CONFIG_MAC80211_RC_DEFAULT_PID is not set
+CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
+CONFIG_MAC80211_RC_DEFAULT="minstrel"
CONFIG_MAC80211_MESH=y
CONFIG_MAC80211_LEDS=y
-# CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is not set
-# CONFIG_MAC80211_DEBUG is not set
-# CONFIG_IEEE80211 is not set
+# CONFIG_MAC80211_DEBUG_MENU is not set
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
-CONFIG_MTD_MAP_BANK_WIDTH_16=y
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_PHYSMAP is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_IMPA7 is not set
-CONFIG_MTD_BAST=y
-CONFIG_MTD_BAST_MAXSIZE=4
# CONFIG_MTD_PLATRAM is not set
#
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
CONFIG_MTD_NAND_IDS=y
CONFIG_MTD_NAND_S3C2410=y
# CONFIG_MTD_NAND_S3C2410_DEBUG is not set
# CONFIG_MTD_ONENAND is not set
#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
CONFIG_BLK_DEV_NBD=m
-# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_UB=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_CDROM_PKTCDVD is not set
CONFIG_ATA_OVER_ETH=m
CONFIG_MISC_DEVICES=y
-# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=m
+CONFIG_EEPROM_AT25=m
+CONFIG_EEPROM_LEGACY=m
+CONFIG_EEPROM_93CX6=m
CONFIG_HAVE_IDE=y
CONFIG_IDE=y
-CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
-CONFIG_BLK_DEV_IDEDISK=y
-# CONFIG_IDEDISK_MULTI_MODE is not set
+CONFIG_IDE_GD=y
+CONFIG_IDE_GD_ATA=y
+# CONFIG_IDE_GD_ATAPI is not set
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
CONFIG_BLK_DEV_IDETAPE=m
-CONFIG_BLK_DEV_IDEFLOPPY=m
-# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
#
-# CONFIG_BLK_DEV_PLATFORM is not set
+CONFIG_BLK_DEV_PLATFORM=y
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
CONFIG_HAVE_PATA_PLATFORM=y
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
+CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_SMC91X is not set
CONFIG_DM9000=y
-# CONFIG_ENC28J60 is not set
CONFIG_DM9000_DEBUGLEVEL=4
+# CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
# CONFIG_NET_VENDOR_RACAL is not set
+# CONFIG_DNET is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_NET_PCI is not set
# CONFIG_B44 is not set
+# CONFIG_CS89x0 is not set
# CONFIG_NET_POCKET is not set
CONFIG_NETDEV_1000=y
-# CONFIG_E1000E_ENABLED is not set
CONFIG_NETDEV_10000=y
# CONFIG_TR is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
#
# USB Network Adapters
# Input device support
#
CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
+CONFIG_INPUT_FF_MEMLESS=m
# CONFIG_INPUT_POLLDEV is not set
#
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
+CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
-CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
-# CONFIG_MOUSE_APPLETOUCH is not set
+CONFIG_MOUSE_APPLETOUCH=m
+CONFIG_MOUSE_BCM5974=m
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_GPIO is not set
-# CONFIG_INPUT_JOYSTICK is not set
+CONFIG_INPUT_JOYSTICK=y
+CONFIG_JOYSTICK_ANALOG=m
+CONFIG_JOYSTICK_A3D=m
+CONFIG_JOYSTICK_ADI=m
+CONFIG_JOYSTICK_COBRA=m
+CONFIG_JOYSTICK_GF2K=m
+CONFIG_JOYSTICK_GRIP=m
+CONFIG_JOYSTICK_GRIP_MP=m
+CONFIG_JOYSTICK_GUILLEMOT=m
+CONFIG_JOYSTICK_INTERACT=m
+CONFIG_JOYSTICK_SIDEWINDER=m
+CONFIG_JOYSTICK_TMDC=m
+CONFIG_JOYSTICK_IFORCE=m
+# CONFIG_JOYSTICK_IFORCE_USB is not set
+# CONFIG_JOYSTICK_IFORCE_232 is not set
+# CONFIG_JOYSTICK_WARRIOR is not set
+CONFIG_JOYSTICK_MAGELLAN=m
+CONFIG_JOYSTICK_SPACEORB=m
+CONFIG_JOYSTICK_SPACEBALL=m
+CONFIG_JOYSTICK_STINGER=m
+CONFIG_JOYSTICK_TWIDJOY=m
+CONFIG_JOYSTICK_ZHENHUA=m
+CONFIG_JOYSTICK_DB9=m
+CONFIG_JOYSTICK_GAMECON=m
+CONFIG_JOYSTICK_TURBOGRAFX=m
+CONFIG_JOYSTICK_JOYDUMP=m
+CONFIG_JOYSTICK_XPAD=m
+CONFIG_JOYSTICK_XPAD_FF=y
+CONFIG_JOYSTICK_XPAD_LEDS=y
# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_HTCPEN is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_WM97XX is not set
+CONFIG_TOUCHSCREEN_USB_COMPOSITE=m
+CONFIG_TOUCHSCREEN_USB_EGALAX=y
+CONFIG_TOUCHSCREEN_USB_PANJIT=y
+CONFIG_TOUCHSCREEN_USB_3M=y
+CONFIG_TOUCHSCREEN_USB_ITM=y
+CONFIG_TOUCHSCREEN_USB_ETURBO=y
+CONFIG_TOUCHSCREEN_USB_GUNZE=y
+CONFIG_TOUCHSCREEN_USB_DMC_TSC10=y
+CONFIG_TOUCHSCREEN_USB_IRTOUCH=y
+CONFIG_TOUCHSCREEN_USB_IDEALTEK=y
+CONFIG_TOUCHSCREEN_USB_GENERAL_TOUCH=y
+CONFIG_TOUCHSCREEN_USB_GOTOP=y
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_ATI_REMOTE=m
+CONFIG_INPUT_ATI_REMOTE2=m
+CONFIG_INPUT_KEYSPAN_REMOTE=m
+CONFIG_INPUT_POWERMATE=m
+CONFIG_INPUT_YEALINK=m
+CONFIG_INPUT_CM109=m
+CONFIG_INPUT_UINPUT=m
+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
#
# Hardware I/O ports
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
-# CONFIG_GAMEPORT is not set
+CONFIG_GAMEPORT=m
+# CONFIG_GAMEPORT_NS558 is not set
+# CONFIG_GAMEPORT_L4 is not set
#
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# Non-8250 serial port support
#
CONFIG_SERIAL_SAMSUNG=y
+CONFIG_SERIAL_SAMSUNG_UARTS=4
# CONFIG_SERIAL_SAMSUNG_DEBUG is not set
CONFIG_SERIAL_SAMSUNG_CONSOLE=y
CONFIG_SERIAL_S3C2410=y
CONFIG_SERIAL_S3C2412=y
CONFIG_SERIAL_S3C2440=y
+# CONFIG_SERIAL_MAX3100 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=y
CONFIG_PPDEV=y
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
-# CONFIG_NVRAM is not set
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_ALGOBIT=y
#
# I2C Hardware Bus support
#
-# CONFIG_I2C_ELEKTOR is not set
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_PARPORT is not set
-# CONFIG_I2C_PARPORT_LIGHT is not set
CONFIG_I2C_S3C2410=y
CONFIG_I2C_SIMTEC=y
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
-# CONFIG_I2C_STUB is not set
# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_ELEKTOR is not set
# CONFIG_I2C_PCA_ISA is not set
# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-CONFIG_EEPROM_LEGACY=m
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCF8591 is not set
-# CONFIG_TPS65010 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
#
CONFIG_SPI_BITBANG=m
# CONFIG_SPI_BUTTERFLY is not set
+CONFIG_SPI_GPIO=m
# CONFIG_SPI_LM70_LLP is not set
CONFIG_SPI_S3C24XX=m
CONFIG_SPI_S3C24XX_GPIO=m
#
# SPI Protocol Masters
#
-# CONFIG_EEPROM_AT25 is not set
-# CONFIG_SPI_SPIDEV is not set
-# CONFIG_SPI_TLE62X0 is not set
-CONFIG_HAVE_GPIO_LIB=y
+CONFIG_SPI_SPIDEV=m
+CONFIG_SPI_TLE62X0=m
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
#
-# GPIO Support
+# Memory mapped GPIO expanders:
#
-# CONFIG_DEBUG_GPIO is not set
#
# I2C GPIO expanders:
#
+# CONFIG_GPIO_MAX732X is not set
# CONFIG_GPIO_PCA953X is not set
# CONFIG_GPIO_PCF857X is not set
#
+# PCI GPIO expanders:
+#
+
+#
# SPI GPIO expanders:
#
+# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
+# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADCXX is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
# CONFIG_SENSORS_ADT7470 is not set
# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1111 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
# CONFIG_SENSORS_DME1737 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_SENSORS_LIS3_SPI is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# USB-based Watchdog Cards
#
# CONFIG_USBPCWATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
-CONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
CONFIG_MFD_SM501=y
+# CONFIG_MFD_SM501_GPIO is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_UCB1400_CORE is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
#
# Multimedia devices
#
# Multimedia core support
#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
+CONFIG_VIDEO_DEV=m
+CONFIG_VIDEO_V4L2_COMMON=m
+CONFIG_VIDEO_ALLOW_V4L1=y
+CONFIG_VIDEO_V4L1_COMPAT=y
+CONFIG_DVB_CORE=m
+CONFIG_VIDEO_MEDIA=m
#
# Multimedia drivers
#
-# CONFIG_DAB is not set
+CONFIG_MEDIA_ATTACH=y
+CONFIG_MEDIA_TUNER=m
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
+CONFIG_MEDIA_TUNER_SIMPLE=m
+CONFIG_MEDIA_TUNER_TDA8290=m
+CONFIG_MEDIA_TUNER_TDA827X=m
+CONFIG_MEDIA_TUNER_TDA18271=m
+CONFIG_MEDIA_TUNER_TDA9887=m
+CONFIG_MEDIA_TUNER_TEA5761=m
+CONFIG_MEDIA_TUNER_TEA5767=m
+CONFIG_MEDIA_TUNER_MT20XX=m
+CONFIG_MEDIA_TUNER_MT2060=m
+CONFIG_MEDIA_TUNER_MT2266=m
+CONFIG_MEDIA_TUNER_QT1010=m
+CONFIG_MEDIA_TUNER_XC2028=m
+CONFIG_MEDIA_TUNER_XC5000=m
+CONFIG_MEDIA_TUNER_MXL5005S=m
+CONFIG_MEDIA_TUNER_MXL5007T=m
+CONFIG_MEDIA_TUNER_MC44S803=m
+CONFIG_VIDEO_V4L2=m
+CONFIG_VIDEO_V4L1=m
+CONFIG_VIDEOBUF_GEN=m
+CONFIG_VIDEOBUF_VMALLOC=m
+CONFIG_VIDEO_TVEEPROM=m
+CONFIG_VIDEO_CAPTURE_DRIVERS=y
+# CONFIG_VIDEO_ADV_DEBUG is not set
+# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
+CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
+CONFIG_VIDEO_VIVI=m
+CONFIG_VIDEO_PMS=m
+CONFIG_VIDEO_BWQCAM=m
+CONFIG_VIDEO_CQCAM=m
+CONFIG_VIDEO_W9966=m
+CONFIG_VIDEO_CPIA=m
+CONFIG_VIDEO_CPIA_PP=m
+CONFIG_VIDEO_CPIA_USB=m
+CONFIG_VIDEO_CPIA2=m
+CONFIG_VIDEO_SAA5246A=m
+CONFIG_VIDEO_SAA5249=m
+CONFIG_VIDEO_AU0828=m
+# CONFIG_SOC_CAMERA is not set
+CONFIG_V4L_USB_DRIVERS=y
+# CONFIG_USB_VIDEO_CLASS is not set
+CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y
+CONFIG_USB_GSPCA=m
+# CONFIG_USB_M5602 is not set
+# CONFIG_USB_STV06XX is not set
+# CONFIG_USB_GSPCA_CONEX is not set
+# CONFIG_USB_GSPCA_ETOMS is not set
+# CONFIG_USB_GSPCA_FINEPIX is not set
+# CONFIG_USB_GSPCA_MARS is not set
+# CONFIG_USB_GSPCA_MR97310A is not set
+# CONFIG_USB_GSPCA_OV519 is not set
+# CONFIG_USB_GSPCA_OV534 is not set
+# CONFIG_USB_GSPCA_PAC207 is not set
+# CONFIG_USB_GSPCA_PAC7311 is not set
+# CONFIG_USB_GSPCA_SONIXB is not set
+# CONFIG_USB_GSPCA_SONIXJ is not set
+# CONFIG_USB_GSPCA_SPCA500 is not set
+# CONFIG_USB_GSPCA_SPCA501 is not set
+# CONFIG_USB_GSPCA_SPCA505 is not set
+# CONFIG_USB_GSPCA_SPCA506 is not set
+# CONFIG_USB_GSPCA_SPCA508 is not set
+# CONFIG_USB_GSPCA_SPCA561 is not set
+# CONFIG_USB_GSPCA_SQ905 is not set
+# CONFIG_USB_GSPCA_SQ905C is not set
+# CONFIG_USB_GSPCA_STK014 is not set
+# CONFIG_USB_GSPCA_SUNPLUS is not set
+# CONFIG_USB_GSPCA_T613 is not set
+# CONFIG_USB_GSPCA_TV8532 is not set
+# CONFIG_USB_GSPCA_VC032X is not set
+# CONFIG_USB_GSPCA_ZC3XX is not set
+# CONFIG_VIDEO_PVRUSB2 is not set
+# CONFIG_VIDEO_HDPVR is not set
+# CONFIG_VIDEO_EM28XX is not set
+# CONFIG_VIDEO_CX231XX is not set
+# CONFIG_VIDEO_USBVISION is not set
+# CONFIG_USB_VICAM is not set
+# CONFIG_USB_IBMCAM is not set
+# CONFIG_USB_KONICAWC is not set
+# CONFIG_USB_QUICKCAM_MESSENGER is not set
+# CONFIG_USB_ET61X251 is not set
+# CONFIG_VIDEO_OVCAMCHIP is not set
+# CONFIG_USB_OV511 is not set
+# CONFIG_USB_SE401 is not set
+# CONFIG_USB_SN9C102 is not set
+# CONFIG_USB_STV680 is not set
+# CONFIG_USB_ZC0301 is not set
+# CONFIG_USB_PWC is not set
+CONFIG_USB_PWC_INPUT_EVDEV=y
+# CONFIG_USB_ZR364XX is not set
+# CONFIG_USB_STKWEBCAM is not set
+# CONFIG_USB_S2255 is not set
+CONFIG_RADIO_ADAPTERS=y
+CONFIG_RADIO_CADET=m
+CONFIG_RADIO_RTRACK=m
+CONFIG_RADIO_RTRACK2=m
+CONFIG_RADIO_AZTECH=m
+CONFIG_RADIO_GEMTEK=m
+CONFIG_RADIO_SF16FMI=m
+CONFIG_RADIO_SF16FMR2=m
+CONFIG_RADIO_TERRATEC=m
+CONFIG_RADIO_TRUST=m
+CONFIG_RADIO_TYPHOON=m
+CONFIG_RADIO_TYPHOON_PROC_FS=y
+CONFIG_RADIO_ZOLTRIX=m
+CONFIG_USB_DSBR=m
+CONFIG_USB_SI470X=m
+CONFIG_USB_MR800=m
+CONFIG_RADIO_TEA5764=m
+CONFIG_DVB_DYNAMIC_MINORS=y
+CONFIG_DVB_CAPTURE_DRIVERS=y
+# CONFIG_TTPCI_EEPROM is not set
+
+#
+# Supported USB Adapters
+#
+CONFIG_DVB_USB=m
+# CONFIG_DVB_USB_DEBUG is not set
+# CONFIG_DVB_USB_A800 is not set
+CONFIG_DVB_USB_DIBUSB_MB=m
+# CONFIG_DVB_USB_DIBUSB_MB_FAULTY is not set
+CONFIG_DVB_USB_DIBUSB_MC=m
+CONFIG_DVB_USB_DIB0700=m
+CONFIG_DVB_USB_UMT_010=m
+CONFIG_DVB_USB_CXUSB=m
+CONFIG_DVB_USB_M920X=m
+# CONFIG_DVB_USB_GL861 is not set
+# CONFIG_DVB_USB_AU6610 is not set
+# CONFIG_DVB_USB_DIGITV is not set
+# CONFIG_DVB_USB_VP7045 is not set
+# CONFIG_DVB_USB_VP702X is not set
+# CONFIG_DVB_USB_GP8PSK is not set
+# CONFIG_DVB_USB_NOVA_T_USB2 is not set
+# CONFIG_DVB_USB_TTUSB2 is not set
+# CONFIG_DVB_USB_DTT200U is not set
+# CONFIG_DVB_USB_OPERA1 is not set
+CONFIG_DVB_USB_AF9005=m
+# CONFIG_DVB_USB_AF9005_REMOTE is not set
+# CONFIG_DVB_USB_DW2102 is not set
+# CONFIG_DVB_USB_CINERGY_T2 is not set
+# CONFIG_DVB_USB_ANYSEE is not set
+# CONFIG_DVB_USB_DTV5100 is not set
+# CONFIG_DVB_USB_AF9015 is not set
+# CONFIG_DVB_USB_CE6230 is not set
+# CONFIG_DVB_SIANO_SMS1XXX is not set
+
+#
+# Supported FlexCopII (B2C2) Adapters
+#
+# CONFIG_DVB_B2C2_FLEXCOP is not set
+
+#
+# Supported DVB Frontends
+#
+# CONFIG_DVB_FE_CUSTOMISE is not set
+CONFIG_DVB_CX22702=m
+CONFIG_DVB_TDA1004X=m
+CONFIG_DVB_MT352=m
+CONFIG_DVB_ZL10353=m
+CONFIG_DVB_DIB3000MB=m
+CONFIG_DVB_DIB3000MC=m
+CONFIG_DVB_DIB7000M=m
+CONFIG_DVB_DIB7000P=m
+CONFIG_DVB_LGDT330X=m
+CONFIG_DVB_LGDT3305=m
+CONFIG_DVB_AU8522=m
+CONFIG_DVB_S5H1411=m
+CONFIG_DVB_PLL=m
+CONFIG_DVB_TUNER_DIB0070=m
+CONFIG_DVB_LGS8GL5=m
+CONFIG_DAB=y
+CONFIG_USB_DABUSB=m
#
# Graphics support
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_S3C2410_DEBUG is not set
CONFIG_FB_SM501=y
# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=m
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_TDO24M is not set
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=m
+CONFIG_BACKLIGHT_GENERIC=m
+CONFIG_BACKLIGHT_PWM=m
#
# Display device support
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_LOGO is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+CONFIG_SOUND_OSS_CORE=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_HWDEP=m
+CONFIG_SND_RAWMIDI=m
+CONFIG_SND_JACK=y
+CONFIG_SND_SEQUENCER=m
+# CONFIG_SND_SEQ_DUMMY is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+CONFIG_SND_SEQUENCER_OSS=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+CONFIG_SND_VERBOSE_PRINTK=y
+# CONFIG_SND_DEBUG is not set
+CONFIG_SND_VMASTER=y
+CONFIG_SND_AC97_CODEC=m
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+# CONFIG_SND_SPI is not set
+CONFIG_SND_USB=y
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_CAIAQ=m
+# CONFIG_SND_USB_CAIAQ_INPUT is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_AC97_BUS=y
+CONFIG_SND_S3C24XX_SOC=y
+CONFIG_SND_S3C24XX_SOC_I2S=m
+CONFIG_SND_S3C_I2SV2_SOC=m
+CONFIG_SND_S3C2412_SOC_I2S=m
+CONFIG_SND_S3C2443_SOC_AC97=m
+CONFIG_SND_S3C24XX_SOC_JIVE_WM8750=m
+CONFIG_SND_S3C24XX_SOC_SMDK2443_WM9710=m
+CONFIG_SND_S3C24XX_SOC_LN2440SBC_ALC650=m
+CONFIG_SND_S3C24XX_SOC_S3C24XX_UDA134X=m
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+CONFIG_SND_SOC_AC97_CODEC=m
+CONFIG_SND_SOC_L3=m
+CONFIG_SND_SOC_UDA134X=m
+CONFIG_SND_SOC_WM8750=m
+# CONFIG_SOUND_PRIME is not set
+CONFIG_AC97_BUS=y
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# USB Input Devices
#
# CONFIG_USB_HID is not set
+# CONFIG_HID_PID is not set
#
-# USB HID Boot Protocol drivers
+# Special HID drivers
#
-# CONFIG_USB_KBD is not set
-# CONFIG_USB_MOUSE is not set
+CONFIG_HID_APPLE=m
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
+CONFIG_USB_MON=y
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_U132_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_MUSB_HDRC is not set
#
# USB Device Class drivers
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_WDM=m
+# CONFIG_USB_TMC is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
-# may also be needed; see USB_STORAGE Help for more information
+# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
-# CONFIG_USB_STORAGE_DATAFAB is not set
-# CONFIG_USB_STORAGE_FREECOM is not set
-# CONFIG_USB_STORAGE_ISD200 is not set
-# CONFIG_USB_STORAGE_DPCM is not set
-# CONFIG_USB_STORAGE_USBAT is not set
-# CONFIG_USB_STORAGE_SDDR09 is not set
-# CONFIG_USB_STORAGE_SDDR55 is not set
-# CONFIG_USB_STORAGE_JUMPSHOT is not set
-# CONFIG_USB_STORAGE_ALAUDA is not set
-# CONFIG_USB_STORAGE_ONETOUCH is not set
-# CONFIG_USB_STORAGE_KARMA is not set
-# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_ONETOUCH=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
CONFIG_USB_LIBUSUAL=y
#
# USB Imaging devices
#
-# CONFIG_USB_MDC800 is not set
-# CONFIG_USB_MICROTEK is not set
-CONFIG_USB_MON=y
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
#
# USB port drivers
#
-# CONFIG_USB_USS720 is not set
+CONFIG_USB_USS720=m
CONFIG_USB_SERIAL=y
# CONFIG_USB_SERIAL_CONSOLE is not set
# CONFIG_USB_EZUSB is not set
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_AIRCABLE is not set
-# CONFIG_USB_SERIAL_AIRPRIME is not set
# CONFIG_USB_SERIAL_ARK3116 is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_CH341 is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
-# CONFIG_USB_SERIAL_CP2101 is not set
+# CONFIG_USB_SERIAL_CP210X is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
CONFIG_USB_SERIAL_FTDI_SIO=y
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=y
# CONFIG_USB_SERIAL_OTI6858 is not set
+# CONFIG_USB_SERIAL_QUALCOMM is not set
# CONFIG_USB_SERIAL_SPCP8X5 is not set
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
+# CONFIG_USB_SERIAL_SIEMENS_MPI is not set
# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
+# CONFIG_USB_SERIAL_SYMBOL is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
CONFIG_USB_SERIAL_OPTION=m
# CONFIG_USB_SERIAL_OMNINET is not set
+# CONFIG_USB_SERIAL_OPTICON is not set
# CONFIG_USB_SERIAL_DEBUG is not set
#
# USB Miscellaneous drivers
#
-# CONFIG_USB_EMI62 is not set
-# CONFIG_USB_EMI26 is not set
-# CONFIG_USB_ADUTUX is not set
-# CONFIG_USB_AUERSWALD is not set
-# CONFIG_USB_RIO500 is not set
-# CONFIG_USB_LEGOTOWER is not set
-# CONFIG_USB_LCD is not set
-# CONFIG_USB_BERRY_CHARGE is not set
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+CONFIG_USB_ADUTUX=m
+CONFIG_USB_SEVSEG=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_BERRY_CHARGE=m
CONFIG_USB_LED=m
-# CONFIG_USB_CYPRESS_CY7C63 is not set
-# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGET is not set
-# CONFIG_USB_IDMOUSE is not set
-# CONFIG_USB_FTDI_ELAN is not set
-# CONFIG_USB_APPLEDISPLAY is not set
+CONFIG_USB_CYPRESS_CY7C63=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_IDMOUSE=m
+CONFIG_USB_FTDI_ELAN=m
+CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_LD=m
-# CONFIG_USB_TRANCEVIBRATOR is not set
-# CONFIG_USB_IOWARRIOR is not set
-# CONFIG_USB_TEST is not set
+CONFIG_USB_TRANCEVIBRATOR=m
+CONFIG_USB_IOWARRIOR=m
+CONFIG_USB_TEST=m
# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
-# CONFIG_MMC is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+CONFIG_SDIO_UART=m
+CONFIG_MMC_TEST=m
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_SDHCI=m
+CONFIG_MMC_SPI=m
+CONFIG_MMC_S3C=y
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m
#
CONFIG_LEDS_S3C24XX=m
CONFIG_LEDS_H1940=m
-# CONFIG_LEDS_GPIO is not set
+CONFIG_LEDS_PCA9532=m
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_GPIO_PLATFORM=y
+CONFIG_LEDS_LP5521=m
+CONFIG_LEDS_PCA955X=m
+CONFIG_LEDS_DAC124S085=m
+CONFIG_LEDS_PWM=m
+CONFIG_LEDS_BD2802=m
#
# LED Triggers
CONFIG_LEDS_TRIGGER_TIMER=m
# CONFIG_LEDS_TRIGGER_IDE_DISK is not set
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
-# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+CONFIG_LEDS_TRIGGER_GPIO=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
#
# SPI RTC drivers
#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
# CONFIG_RTC_DRV_MAX6902 is not set
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_S3C=y
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
#
# File systems
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
-# CONFIG_EXT4DEV_FS is not set
+CONFIG_EXT4_FS=m
+# CONFIG_EXT4DEV_COMPAT is not set
+CONFIG_EXT4_FS_XATTR=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+# CONFIG_EXT4_FS_SECURITY is not set
CONFIG_JBD=y
+CONFIG_JBD2=m
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
+CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
+CONFIG_AUTOFS_FS=m
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=m
CONFIG_GENERIC_ACL=y
#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=m
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=y
+CONFIG_SQUASHFS=m
+# CONFIG_SQUASHFS_EMBEDDED is not set
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
CONFIG_ROMFS_FS=y
+CONFIG_ROMFS_BACKED_BY_BLOCK=y
+# CONFIG_ROMFS_BACKED_BY_MTD is not set
+# CONFIG_ROMFS_BACKED_BY_BOTH is not set
+CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V2_ACL=y
+CONFIG_NFSD_V3=y
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_EXPORTFS=m
+CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
-# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_SUNRPC_GSS=m
+CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
+CONFIG_CIFS=m
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_WEAK_PW_HASH is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_ERRORS=y
# CONFIG_DEBUG_STACK_USAGE is not set
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
+# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=m
+CONFIG_CRYPTO_ALGAPI2=m
CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AEAD2=m
CONFIG_CRYPTO_BLKCIPHER=m
+CONFIG_CRYPTO_BLKCIPHER2=m
CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=m
+CONFIG_CRYPTO_RNG2=m
+CONFIG_CRYPTO_PCOMP=m
CONFIG_CRYPTO_MANAGER=m
+CONFIG_CRYPTO_MANAGER2=m
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=m
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_AUTHENC=m
# CONFIG_CRYPTO_TEST is not set
#
# Digest
#
-# CONFIG_CRYPTO_CRC32C is not set
+CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=m
# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=m
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# Compression
#
CONFIG_CRYPTO_DEFLATE=m
+# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-# CONFIG_GENERIC_FIND_NEXT_BIT is not set
+CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
+CONFIG_CRC16=m
+# CONFIG_CRC_T10DIF is not set
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
+CONFIG_CRC7=m
+CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_TEXTSEARCH=y
+CONFIG_TEXTSEARCH_KMP=m
+CONFIG_TEXTSEARCH_BM=m
+CONFIG_TEXTSEARCH_FSM=m
CONFIG_HAS_IOMEM=y
CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
struct mmu_gather {
struct mm_struct *mm;
unsigned int fullmm;
+ unsigned long range_start;
+ unsigned long range_end;
};
DECLARE_PER_CPU(struct mmu_gather, mmu_gathers);
put_cpu_var(mmu_gathers);
}
-#define tlb_remove_tlb_entry(tlb,ptep,address) do { } while (0)
+/*
+ * Memorize the range for the TLB flush.
+ */
+static inline void
+tlb_remove_tlb_entry(struct mmu_gather *tlb, pte_t *ptep, unsigned long addr)
+{
+ if (!tlb->fullmm) {
+ if (addr < tlb->range_start)
+ tlb->range_start = addr;
+ if (addr + PAGE_SIZE > tlb->range_end)
+ tlb->range_end = addr + PAGE_SIZE;
+ }
+}
/*
* In the case of tlb vma handling, we can optimise these away in the
static inline void
tlb_start_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
{
- if (!tlb->fullmm)
+ if (!tlb->fullmm) {
flush_cache_range(vma, vma->vm_start, vma->vm_end);
+ tlb->range_start = TASK_SIZE;
+ tlb->range_end = 0;
+ }
}
static inline void
tlb_end_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
{
- if (!tlb->fullmm)
- flush_tlb_range(vma, vma->vm_start, vma->vm_end);
+ if (!tlb->fullmm && tlb->range_end > 0)
+ flush_tlb_range(vma, tlb->range_start, tlb->range_end);
}
#define tlb_remove_page(tlb,page) free_page_and_swap_cache(page)
#include <linux/net.h>
#include <linux/ipc.h>
#include <linux/uaccess.h>
+#include <linux/slab.h>
struct oldabi_stat64 {
unsigned long long st_dev;
#define TIMER4_TICKS_PER_JIFFY ((CLOCK_TICK_RATE + (HZ/2)) / HZ)
-static int ep93xx_timer_interrupt(int irq, void *dev_id)
+static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
{
__raw_writel(1, EP93XX_TIMER1_CLEAR);
while ((signed long)
#include <mach/common.h>
#include <mach/imx-uart.h>
#include <mach/irqs.h>
-#ifdef CONFIG_I2C_IMX
#include <mach/i2c.h>
-#endif
#include <mach/iomux.h>
#include "devices.h"
* I2C
*/
-#ifdef CONFIG_I2C_IMX
static int i2c_pins[] = {
PA15_PF_I2C_SDA,
PA16_PF_I2C_SCL,
.platform_data = &pcf857x_data[1],
},
};
-#endif
/*
* Board init
mxc_register_device(&flash_device, &mx1ads_flash_data);
/* I2C */
-#ifdef CONFIG_I2C_IMX
i2c_register_board_info(0, mx1ads_i2c_devices,
ARRAY_SIZE(mx1ads_i2c_devices));
mxc_register_device(&imx_i2c_device, &mx1ads_i2c_data);
-#endif
}
static void __init mx1ads_timer_init(void)
_REGISTER_CLOCK(NULL, "cspi1", cspi_clk[0])
_REGISTER_CLOCK(NULL, "cspi2", cspi_clk[1])
_REGISTER_CLOCK(NULL, "cspi3", cspi_clk[2])
- _REGISTER_CLOCK(NULL, "lcdc", lcdc_clk[0])
+ _REGISTER_CLOCK("imx-fb.0", NULL, lcdc_clk[0])
_REGISTER_CLOCK(NULL, "csi", csi_clk[0])
_REGISTER_CLOCK(NULL, "usb", usb_clk[0])
_REGISTER_CLOCK(NULL, "ssi1", ssi_clk[0])
_REGISTER_CLOCK(NULL, "ssi2", ssi_clk[1])
- _REGISTER_CLOCK(NULL, "nfc", nfc_clk)
+ _REGISTER_CLOCK("mxc_nand.0", NULL, nfc_clk)
_REGISTER_CLOCK(NULL, "dma", dma_clk[0])
_REGISTER_CLOCK(NULL, "brom", brom_clk)
_REGISTER_CLOCK(NULL, "emma", emma_clk[0])
_REGISTER_CLOCK(NULL, "slcdc", slcdc_clk[0])
- _REGISTER_CLOCK(NULL, "wdog", wdog_clk)
+ _REGISTER_CLOCK("imx-wdt.0", NULL, wdog_clk)
_REGISTER_CLOCK(NULL, "gpio", gpio_clk)
- _REGISTER_CLOCK(NULL, "i2c", i2c_clk)
+ _REGISTER_CLOCK("imx-i2c.0", NULL, i2c_clk)
_REGISTER_CLOCK("mxc-keypad", NULL, kpp_clk)
_REGISTER_CLOCK(NULL, "owire", owire_clk)
_REGISTER_CLOCK(NULL, "rtc", rtc_clk)
config MACH_MX31ADS_WM1133_EV1
bool "Support Wolfson Microelectronics 1133-EV1 module"
depends on MACH_MX31ADS
+ depends on MFD_WM8350_I2C
+ depends on REGULATOR_WM8350
select MFD_WM8350_CONFIG_MODE_0
select MFD_WM8352_CONFIG_MODE_0
help
.flags = IMXUART_HAVE_RTSCTS,
};
-static int uart_pins[] = {
+static unsigned int uart_pins[] = {
MX31_PIN_CTS1__CTS1,
MX31_PIN_RTS1__RTS1,
MX31_PIN_TXD1__TXD1,
wm8350->codec.platform_data = &imx32ads_wm8350_setup;
+ regulator_has_full_constraints();
+
return 0;
}
mxc_iomux_setup_pin(MX31_PIN_BATT_LINE__OWIRE, "batt-0wire");
mxc_register_device(&mxc_w1_master_device, NULL);
- /* SMSC9215 IRQ pin */
+ /* LAN9217 IRQ pin */
if (!mxc_iomux_setup_pin(IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO),
"pcm037-eth"))
- gpio_direction_input(MX31_PIN_GPIO3_1);
+ gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
#ifdef CONFIG_I2C_IMX
i2c_register_board_info(1, pcm037_i2c_devices,
}
/*
- * This structure defines the MX31 memory map.
- */
-static struct map_desc qong_io_desc[] __initdata = {
- {
- .virtual = AIPS1_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(AIPS1_BASE_ADDR),
- .length = AIPS1_SIZE,
- .type = MT_DEVICE_NONSHARED
- }, {
- .virtual = AIPS2_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(AIPS2_BASE_ADDR),
- .length = AIPS2_SIZE,
- .type = MT_DEVICE_NONSHARED
- }
-};
-
-/*
- * Set up static virtual mappings.
- */
-static void __init qong_map_io(void)
-{
- mxc_map_io();
- iotable_init(qong_io_desc, ARRAY_SIZE(qong_io_desc));
-}
-
-/*
* Board specific initialization.
*/
static void __init mxc_board_init(void)
.phys_io = AIPS1_BASE_ADDR,
.io_pg_offst = ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc,
.boot_params = PHYS_OFFSET + 0x100,
- .map_io = qong_map_io,
+ .map_io = mxc_map_io,
.init_irq = mxc_init_irq,
.init_machine = mxc_board_init,
.timer = &qong_timer,
#include <linux/spi/libertas_spi.h>
#include <linux/power_supply.h>
#include <linux/apm-emulation.h>
-#include <linux/delay.h>
#include <media/soc_camera.h>
};
static struct pxa2xx_spi_chip em_x270_tdo24m_chip = {
- .rx_threshold = 1,
- .tx_threshold = 1,
+ .rx_threshold = 1,
+ .tx_threshold = 1,
+ .gpio_cs = -1,
};
static struct tdo24m_platform_data em_x270_tdo24m_pdata = {
extern void __init pxa_init_irq(int irq_nr,
int (*set_wake)(unsigned int, unsigned int));
extern void __init pxa25x_init_irq(void);
+#ifdef CONFIG_CPU_PXA26x
+extern void __init pxa26x_init_irq(void);
+#endif
extern void __init pxa27x_init_irq(void);
extern void __init pxa3xx_init_irq(void);
extern void __init pxa_map_io(void);
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
extern void colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin);
#else
-static inline void colibri_pxa3xx_init_mmc(mfp_cfg_t *, int, int) {}
+static inline void colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin) {}
#endif
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
extern void colibri_pxa3xx_init_lcd(int bl_pin);
#else
-static inline void colibri_pxa3xx_init_lcd(int) {}
+static inline void colibri_pxa3xx_init_lcd(int bl_pin) {}
#endif
#if defined(CONFIG_AX88796)
/* USB */
#define GPIO_NR_PALMT5_USB_DETECT_N 15
-#define GPIO_NR_PALMT5_USB_POWER 95
#define GPIO_NR_PALMT5_USB_PULLUP 93
/* LCD/BACKLIGHT */
/* USB */
#define GPIO_NR_PALMTX_USB_DETECT_N 13
-#define GPIO_NR_PALMTX_USB_POWER 95
#define GPIO_NR_PALMTX_USB_PULLUP 93
/* LCD/BACKLIGHT */
GPIO29_AC97_SDATA_IN_0,
GPIO30_AC97_SDATA_OUT,
GPIO31_AC97_SYNC,
+ GPIO95_AC97_nRESET,
/* IrDA */
GPIO40_GPIO, /* ir disable */
/* USB */
GPIO15_GPIO, /* usb detect */
- GPIO95_GPIO, /* usb power */
+ GPIO93_GPIO, /* usb power */
/* MATRIX KEYPAD */
GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
static struct pxa2xx_udc_mach_info palmt5_udc_info __initdata = {
.gpio_vbus = GPIO_NR_PALMT5_USB_DETECT_N,
.gpio_vbus_inverted = 1,
- .gpio_pullup = GPIO_NR_PALMT5_USB_POWER,
+ .gpio_pullup = GPIO_NR_PALMT5_USB_PULLUP,
.gpio_pullup_inverted = 0,
};
/* setup udc GPIOs initial state */
static void __init palmt5_udc_init(void)
{
- if (!gpio_request(GPIO_NR_PALMT5_USB_POWER, "UDC Vbus")) {
- gpio_direction_output(GPIO_NR_PALMT5_USB_POWER, 1);
- gpio_free(GPIO_NR_PALMT5_USB_POWER);
+ if (!gpio_request(GPIO_NR_PALMT5_USB_PULLUP, "UDC Vbus")) {
+ gpio_direction_output(GPIO_NR_PALMT5_USB_PULLUP, 1);
+ gpio_free(GPIO_NR_PALMT5_USB_PULLUP);
}
}
GPIO29_AC97_SDATA_IN_0,
GPIO30_AC97_SDATA_OUT,
GPIO31_AC97_SYNC,
+ GPIO95_AC97_nRESET,
/* IrDA */
GPIO40_GPIO, /* ir disable */
/* USB */
GPIO13_GPIO, /* usb detect */
- GPIO95_GPIO, /* usb power */
+ GPIO93_GPIO, /* usb power */
/* PCMCIA */
GPIO48_nPOE,
static struct pxa2xx_udc_mach_info palmtx_udc_info __initdata = {
.gpio_vbus = GPIO_NR_PALMTX_USB_DETECT_N,
.gpio_vbus_inverted = 1,
- .gpio_pullup = GPIO_NR_PALMTX_USB_POWER,
+ .gpio_pullup = GPIO_NR_PALMTX_USB_PULLUP,
.gpio_pullup_inverted = 0,
};
/* setup udc GPIOs initial state */
static void __init palmtx_udc_init(void)
{
- if (!gpio_request(GPIO_NR_PALMTX_USB_POWER, "UDC Vbus")) {
- gpio_direction_output(GPIO_NR_PALMTX_USB_POWER, 1);
- gpio_free(GPIO_NR_PALMTX_USB_POWER);
+ if (!gpio_request(GPIO_NR_PALMTX_USB_PULLUP, "UDC Vbus")) {
+ gpio_direction_output(GPIO_NR_PALMTX_USB_PULLUP, 1);
+ gpio_free(GPIO_NR_PALMTX_USB_PULLUP);
}
}
#include <plat/cpu.h>
#include <plat/pm.h>
#include <plat/udc.h>
-#include <plat/iic.h>
static struct map_desc jive_iodesc[] __initdata = {
};
#define LCD_HTOT (LCD_HSYNC + LCD_LEFT_MARGIN + LCD_XRES + LCD_RIGHT_MARGIN)
#define LCD_VTOT (LCD_VSYNC + LCD_LOWER_MARGIN + LCD_YRES + LCD_UPPER_MARGIN)
-struct s3c2410fb_display jive_vgg2432a4_display[] = {
+static struct s3c2410fb_display jive_vgg2432a4_display[] = {
[0] = {
.width = LCD_XRES,
.height = LCD_YRES,
#define S3C2410_GPCCON_MASK(x) (3 << ((x) * 2))
#define S3C2410_GPDCON_MASK(x) (3 << ((x) * 2))
-struct s3c2410fb_mach_info jive_lcd_config = {
+static struct s3c2410fb_mach_info jive_lcd_config = {
.displays = jive_vgg2432a4_display,
.num_displays = ARRAY_SIZE(jive_vgg2432a4_display),
.default_display = 0,
/* IDE channels */
-struct pata_platform_info anubis_ide_platdata = {
+static struct pata_platform_info anubis_ide_platdata = {
.ioport_shift = 5,
};
.io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
.boot_params = S3C2410_SDRAM_PA + 0x100,
.map_io = osiris_map_io,
- .init_machine = osiris_init,
.init_irq = s3c24xx_init_irq,
.init_machine = osiris_init,
.timer = &s3c24xx_timer,
s3c_i2c1_set_platdata(NULL);
s3c_fb_set_platdata(&smdk6410_lcd_pdata);
+ gpio_request(S3C64XX_GPN(5), "LCD power");
+ gpio_request(S3C64XX_GPF(13), "LCD power");
+ gpio_request(S3C64XX_GPF(15), "LCD power");
+
i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
unsigned int flags;
};
-int __init imx_init_uart(int uart_no, struct imxuart_platform_data *pdata);
-
#endif
*/
#define MX31_PIN_CSPI3_MOSI__RXD3 IOMUX_MODE(MX31_PIN_CSPI3_MOSI, IOMUX_CONFIG_ALT1)
#define MX31_PIN_CSPI3_MISO__TXD3 IOMUX_MODE(MX31_PIN_CSPI3_MISO, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_CSPI3_SCLK__RTS3 IOMUX_MODE(MX31_PIN_CSPI3_SCLK, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_CSPI3_SPI_RDY__CTS3 IOMUX_MODE(MX31_PIN_CSPI3_SPI_RDY, IOMUX_CONFIG_ALT1)
#define MX31_PIN_CTS1__CTS1 IOMUX_MODE(MX31_PIN_CTS1, IOMUX_CONFIG_FUNC)
#define MX31_PIN_RTS1__RTS1 IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_FUNC)
#define MX31_PIN_TXD1__TXD1 IOMUX_MODE(MX31_PIN_TXD1, IOMUX_CONFIG_FUNC)
#define MX31_PIN_SD1_DATA0__SD1_DATA0 IOMUX_MODE(MX31_PIN_SD1_DATA0, IOMUX_CONFIG_FUNC)
#define MX31_PIN_SD1_CLK__SD1_CLK IOMUX_MODE(MX31_PIN_SD1_CLK, IOMUX_CONFIG_FUNC)
#define MX31_PIN_SD1_CMD__SD1_CMD IOMUX_MODE(MX31_PIN_SD1_CMD, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_ATA_CS0__GPIO3_26 IOMUX_MODE(MX31_PIN_ATA_CS0, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_ATA_CS1__GPIO3_27 IOMUX_MODE(MX31_PIN_ATA_CS1, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_PC_PWRON__SD2_DATA3 IOMUX_MODE(MX31_PIN_PC_PWRON, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_PC_VS1__SD2_DATA2 IOMUX_MODE(MX31_PIN_PC_VS1, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_PC_READY__SD2_DATA1 IOMUX_MODE(MX31_PIN_PC_READY, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_PC_WAIT_B__SD2_DATA0 IOMUX_MODE(MX31_PIN_PC_WAIT_B, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_PC_CD2_B__SD2_CLK IOMUX_MODE(MX31_PIN_PC_CD2_B, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_PC_CD1_B__SD2_CMD IOMUX_MODE(MX31_PIN_PC_CD1_B, IOMUX_CONFIG_ALT1)
+#define MX31_PIN_ATA_DIOR__GPIO3_28 IOMUX_MODE(MX31_PIN_ATA_DIOR, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_ATA_DIOW__GPIO3_29 IOMUX_MODE(MX31_PIN_ATA_DIOW, IOMUX_CONFIG_GPIO)
#define MX31_PIN_LD0__LD0 IOMUX_MODE(MX31_PIN_LD0, IOMUX_CONFIG_FUNC)
#define MX31_PIN_LD1__LD1 IOMUX_MODE(MX31_PIN_LD1, IOMUX_CONFIG_FUNC)
#define MX31_PIN_LD2__LD2 IOMUX_MODE(MX31_PIN_LD2, IOMUX_CONFIG_FUNC)
#define MX31_PIN_D3_SPL__D3_SPL IOMUX_MODE(MX31_PIN_D3_SPL, IOMUX_CONFIG_FUNC)
#define MX31_PIN_D3_CLS__D3_CLS IOMUX_MODE(MX31_PIN_D3_CLS, IOMUX_CONFIG_FUNC)
#define MX31_PIN_LCS0__GPI03_23 IOMUX_MODE(MX31_PIN_LCS0, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_GPIO1_1__GPIO IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_I2C_CLK__SCL IOMUX_MODE(MX31_PIN_I2C_CLK, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_I2C_DAT__SDA IOMUX_MODE(MX31_PIN_I2C_DAT, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_DCD_DTE1__I2C2_SDA IOMUX_MODE(MX31_PIN_DCD_DTE1, IOMUX_CONFIG_ALT2)
+#define MX31_PIN_RI_DTE1__I2C2_SCL IOMUX_MODE(MX31_PIN_RI_DTE1, IOMUX_CONFIG_ALT2)
+#define MX31_PIN_CSI_D4__CSI_D4 IOMUX_MODE(MX31_PIN_CSI_D4, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D5__CSI_D5 IOMUX_MODE(MX31_PIN_CSI_D5, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D6__CSI_D6 IOMUX_MODE(MX31_PIN_CSI_D6, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D7__CSI_D7 IOMUX_MODE(MX31_PIN_CSI_D7, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D8__CSI_D8 IOMUX_MODE(MX31_PIN_CSI_D8, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D9__CSI_D9 IOMUX_MODE(MX31_PIN_CSI_D9, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D10__CSI_D10 IOMUX_MODE(MX31_PIN_CSI_D10, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D11__CSI_D11 IOMUX_MODE(MX31_PIN_CSI_D11, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D12__CSI_D12 IOMUX_MODE(MX31_PIN_CSI_D12, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D13__CSI_D13 IOMUX_MODE(MX31_PIN_CSI_D13, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D14__CSI_D14 IOMUX_MODE(MX31_PIN_CSI_D14, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_D15__CSI_D15 IOMUX_MODE(MX31_PIN_CSI_D15, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_HSYNC__CSI_HSYNC IOMUX_MODE(MX31_PIN_CSI_HSYNC, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_MCLK__CSI_MCLK IOMUX_MODE(MX31_PIN_CSI_MCLK, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_PIXCLK__CSI_PIXCLK IOMUX_MODE(MX31_PIN_CSI_PIXCLK, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_CSI_VSYNC__CSI_VSYNC IOMUX_MODE(MX31_PIN_CSI_VSYNC, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_GPIO3_0__GPIO3_0 IOMUX_MODE(MX31_PIN_GPIO3_0, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_GPIO3_1__GPIO3_1 IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_TXD2__GPIO1_28 IOMUX_MODE(MX31_PIN_TXD2, IOMUX_CONFIG_GPIO)
+#define MX31_PIN_USBOTG_DATA0__USBOTG_DATA0 IOMUX_MODE(MX31_PIN_USBOTG_DATA0, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DATA1__USBOTG_DATA1 IOMUX_MODE(MX31_PIN_USBOTG_DATA1, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DATA2__USBOTG_DATA2 IOMUX_MODE(MX31_PIN_USBOTG_DATA2, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DATA3__USBOTG_DATA3 IOMUX_MODE(MX31_PIN_USBOTG_DATA3, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DATA4__USBOTG_DATA4 IOMUX_MODE(MX31_PIN_USBOTG_DATA4, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DATA5__USBOTG_DATA5 IOMUX_MODE(MX31_PIN_USBOTG_DATA5, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DATA6__USBOTG_DATA6 IOMUX_MODE(MX31_PIN_USBOTG_DATA6, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DATA7__USBOTG_DATA7 IOMUX_MODE(MX31_PIN_USBOTG_DATA7, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_CLK__USBOTG_CLK IOMUX_MODE(MX31_PIN_USBOTG_CLK, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_DIR__USBOTG_DIR IOMUX_MODE(MX31_PIN_USBOTG_DIR, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_NXT__USBOTG_NXT IOMUX_MODE(MX31_PIN_USBOTG_NXT, IOMUX_CONFIG_FUNC)
+#define MX31_PIN_USBOTG_STP__USBOTG_STP IOMUX_MODE(MX31_PIN_USBOTG_STP, IOMUX_CONFIG_FUNC)
/*XXX: The SS0, SS1, SS2, SS3 lines of spi3 are multiplexed by cspi2_ss0, cspi2_ss1, cspi1_ss0
* cspi1_ss1*/
#define NR_IRQS (MXC_IPU_IRQ_START + MX3_IPU_IRQS)
-extern void imx_irq_set_priority(unsigned char irq, unsigned char prio);
+extern int imx_irq_set_priority(unsigned char irq, unsigned char prio);
/* all normal IRQs can be FIQs */
#define FIQ_START 0
#define IRAM_BASE_ADDR 0xFFFFE800 /* internal ram */
-/* this CPU supports up to 192 GPIOs (don't forget the baseboard!) */
-#define ARCH_NR_GPIOS (6*32 + 16)
-
/* fixed interrupt numbers */
#define MXC_INT_USBCTRL 58
#define MXC_INT_USBCTRL 58
#define IIM_PROD_REV_SH 3
#define IIM_PROD_REV_LEN 5
-#ifdef CONFIG_MXC_IRQ_PRIOR
-void imx_irq_set_priority(unsigned char irq, unsigned char prio)
+int imx_irq_set_priority(unsigned char irq, unsigned char prio)
{
+#ifdef CONFIG_MXC_IRQ_PRIOR
unsigned int temp;
unsigned int mask = 0x0F << irq % 8 * 4;
- if (irq > 63)
- return;
+ if (irq >= MXC_INTERNAL_IRQS)
+ return -EINVAL;;
temp = __raw_readl(AVIC_NIPRIORITY(irq / 8));
temp &= ~mask;
temp |= prio & mask;
__raw_writel(temp, AVIC_NIPRIORITY(irq / 8));
+
+ return 0;
+#else
+ return -ENOSYS;
+#endif
}
EXPORT_SYMBOL(imx_irq_set_priority);
-#endif
#ifdef CONFIG_FIQ
int mxc_set_irq_fiq(unsigned int irq, unsigned int type)
*/
#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/gpio.h>
#include <linux/io.h>
return ret;
}
+EXPORT_SYMBOL(s3c_gpio_cfgpin);
int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull)
{
return ret;
}
+EXPORT_SYMBOL(s3c_gpio_setpull);
#ifdef CONFIG_S3C_GPIO_CFG_S3C24XX
int s3c_gpio_setcfg_s3c24xx_banka(struct s3c_gpio_chip *chip,
extern struct platform_device s3c_device_rtc;
extern struct platform_device s3c_device_adc;
extern struct platform_device s3c_device_sdi;
+extern struct platform_device s3c_device_hwmon;
extern struct platform_device s3c_device_hsmmc0;
extern struct platform_device s3c_device_hsmmc1;
extern struct platform_device s3c_device_hsmmc2;
readl(adc->regs + S3C2410_ADCDLY));
}
-void s3c_adc_try(struct adc_device *adc)
+static void s3c_adc_try(struct adc_device *adc)
{
struct s3c_adc_client *next = adc->ts_pend;
void s3c_adc_release(struct s3c_adc_client *client)
{
/* We should really check that nothing is in progress. */
+ if (adc_dev->cur == client)
+ adc_dev->cur = NULL;
+ if (adc_dev->ts_pend == client)
+ adc_dev->ts_pend = NULL;
+ else {
+ struct list_head *p, *n;
+ struct s3c_adc_client *tmp;
+
+ list_for_each_safe(p, n, &adc_pending) {
+ tmp = list_entry(p, struct s3c_adc_client, pend);
+ if (tmp == client)
+ list_del(&tmp->pend);
+ }
+ }
+
+ if (adc_dev->cur == NULL)
+ s3c_adc_try(adc_dev);
kfree(client);
}
EXPORT_SYMBOL_GPL(s3c_adc_release);
#include <linux/io.h>
#include <linux/gpio.h>
-#include <plat/gpio-core.h>
+#include <mach/gpio-core.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#ifndef _ASM_BUG_H
#define _ASM_BUG_H
+#ifdef CONFIG_BUG
+
/*
* Tell the user there is some problem.
*/
-#define _debug_bug_trap() \
+#define BUG() \
do { \
asm volatile( \
" syscall 15 \n" \
: \
: "i"(__FILE__), "i"(__LINE__) \
); \
-} while (0)
-
-#define BUG() _debug_bug_trap()
+} while (1)
#define HAVE_ARCH_BUG
+#endif /* CONFIG_BUG */
+
#include <asm-generic/bug.h>
#endif /* _ASM_BUG_H */
#define __NR_dup3 331
#define __NR_pipe2 332
#define __NR_inotify_init1 333
+#define __NR_preadv 334
+#define __NR_pwritev 335
#ifdef __KERNEL__
.long sys_dup3
.long sys_pipe2
.long sys_inotify_init1
+ .long sys_preadv
+ .long sys_pwritev /* 335 */
nr_syscalls=(.-sys_call_table)/4
data_resource.start = virt_to_bus(&_etext);
data_resource.end = virt_to_bus(&_edata)-1;
-#define PFN_UP(x) (((x) + PAGE_SIZE-1) >> PAGE_SHIFT)
-#define PFN_DOWN(x) ((x) >> PAGE_SHIFT)
-#define PFN_PHYS(x) ((x) << PAGE_SHIFT)
-
start_pfn = (CONFIG_KERNEL_RAM_BASE_ADDRESS >> PAGE_SHIFT);
kstart_pfn = PFN_UP(__pa(&_text));
free_pfn = PFN_UP(__pa(&_end));
config PPC_256K_PAGES
bool "256k page size" if 44x
- depends on !STDBINUTILS && (!SHMEM || BROKEN)
+ depends on !STDBINUTILS
help
Make the page size 256k.
interrupt-parent = <&mpic>;
dfsrr;
- dtt@50 {
+ dtt@48 {
compatible = "national,lm75";
- reg = <0x50>;
+ reg = <0x48>;
};
rtc@68 {
interrupt-parent = <&mpic>;
dfsrr;
- dtt@50 {
+ dtt@48 {
compatible = "national,lm75";
- reg = <0x50>;
+ reg = <0x48>;
};
rtc@68 {
interrupt-parent = <&mpic>;
dfsrr;
- dtt@50 {
+ dtt@48 {
compatible = "national,lm75";
- reg = <0x50>;
+ reg = <0x48>;
};
rtc@68 {
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
- phy-handle = <&phy3>;
+ phy-handle = <&phy4>;
mdio@520 {
#address-cells = <1>;
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
- phy-handle = <&phy4>;
+ phy-handle = <&phy5>;
mdio@520 {
#address-cells = <1>;
interrupt-parent = <&mpic>;
dfsrr;
- dtt@50 {
+ dtt@48 {
compatible = "national,lm75";
- reg = <0x50>;
+ reg = <0x48>;
};
rtc@68 {
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
- phy-handle = <&phy3>;
+ phy-handle = <&phy4>;
mdio@520 {
#address-cells = <1>;
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
- phy-handle = <&phy4>;
+ phy-handle = <&phy5>;
mdio@520 {
#address-cells = <1>;
interrupt-parent = <&mpic>;
dfsrr;
- dtt@50 {
+ dtt@48 {
compatible = "national,lm75";
- reg = <0x50>;
+ reg = <0x48>;
};
rtc@68 {
interrupt-parent = <&mpic>;
dfsrr;
- dtt@50 {
+ dtt@48 {
compatible = "national,lm75";
- reg = <0x50>;
+ reg = <0x48>;
};
rtc@68 {
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.29-rc2
-# Mon Jan 26 15:36:20 2009
+# Linux kernel version: 2.6.29-rc7
+# Mon Mar 16 09:03:28 2009
#
# CONFIG_PPC64 is not set
# CONFIG_PHYS_64BIT is not set
CONFIG_SPE=y
CONFIG_PPC_MMU_NOHASH=y
+CONFIG_PPC_BOOK3E_MMU=y
# CONFIG_PPC_MM_SLICES is not set
# CONFIG_SMP is not set
CONFIG_PPC32=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_FREEZER is not set
#
#
# Kernel options
#
-# CONFIG_HIGHMEM is not set
+CONFIG_HIGHMEM=y
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_PPC_4K_PAGES=y
# CONFIG_PPC_16K_PAGES is not set
# CONFIG_PPC_64K_PAGES is not set
+# CONFIG_PPC_256K_PAGES is not set
CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_FSL_SOC=y
CONFIG_FSL_PCI=y
+CONFIG_FSL_LBC=y
CONFIG_PPC_PCI_CHOICE=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# Default settings for advanced configuration options are used
#
CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_LOWMEM_CAM_NUM=3
CONFIG_PAGE_OFFSET=0xc0000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_PHYSICAL_START=0x00000000
-CONFIG_PHYSICAL_ALIGN=0x10000000
+CONFIG_PHYSICAL_ALIGN=0x04000000
CONFIG_TASK_SIZE=0xc0000000
CONFIG_NET=y
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
# CONFIG_PHONET is not set
-CONFIG_WIRELESS=y
-# CONFIG_CFG80211 is not set
-CONFIG_WIRELESS_OLD_REGULATORY=y
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+# CONFIG_WIRELESS is not set
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_NAND_FSL_ELBC is not set
-# CONFIG_MTD_NAND_FSL_UPM is not set
+CONFIG_MTD_NAND_FSL_UPM=y
# CONFIG_MTD_ONENAND is not set
#
# LPDDR flash memory drivers
#
# CONFIG_MTD_LPDDR is not set
-# CONFIG_MTD_QINFO_PROBE is not set
#
# UBI - Unsorted block images
#
-CONFIG_MTD_UBI=m
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_MTD_UBI_BEB_RESERVE=1
-# CONFIG_MTD_UBI_GLUEBI is not set
-
-#
-# UBI debugging options
-#
-# CONFIG_MTD_UBI_DEBUG is not set
+# CONFIG_MTD_UBI is not set
CONFIG_OF_DEVICE=y
CONFIG_OF_I2C=y
# CONFIG_PARPORT is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
-# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_HP_ILO is not set
# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_93CX6 is not set
CONFIG_HAVE_IDE=y
-CONFIG_IDE=y
-
-#
-# Please see Documentation/ide/ide.txt for help/info on IDE drives
-#
-CONFIG_IDE_TIMINGS=y
-# CONFIG_BLK_DEV_IDE_SATA is not set
-CONFIG_IDE_GD=y
-CONFIG_IDE_GD_ATA=y
-# CONFIG_IDE_GD_ATAPI is not set
-# CONFIG_BLK_DEV_IDECD is not set
-# CONFIG_BLK_DEV_IDETAPE is not set
-# CONFIG_IDE_TASK_IOCTL is not set
-CONFIG_IDE_PROC_FS=y
-
-#
-# IDE chipset support/bugfixes
-#
-# CONFIG_BLK_DEV_PLATFORM is not set
-CONFIG_BLK_DEV_IDEDMA_SFF=y
-
-#
-# PCI IDE chipsets support
-#
-CONFIG_BLK_DEV_IDEPCI=y
-CONFIG_IDEPCI_PCIBUS_ORDER=y
-# CONFIG_BLK_DEV_OFFBOARD is not set
-CONFIG_BLK_DEV_GENERIC=y
-# CONFIG_BLK_DEV_OPTI621 is not set
-CONFIG_BLK_DEV_IDEDMA_PCI=y
-# CONFIG_BLK_DEV_AEC62XX is not set
-# CONFIG_BLK_DEV_ALI15X3 is not set
-# CONFIG_BLK_DEV_AMD74XX is not set
-# CONFIG_BLK_DEV_CMD64X is not set
-# CONFIG_BLK_DEV_TRIFLEX is not set
-# CONFIG_BLK_DEV_CS5520 is not set
-# CONFIG_BLK_DEV_CS5530 is not set
-# CONFIG_BLK_DEV_HPT366 is not set
-# CONFIG_BLK_DEV_JMICRON is not set
-# CONFIG_BLK_DEV_SC1200 is not set
-# CONFIG_BLK_DEV_PIIX is not set
-# CONFIG_BLK_DEV_IT8172 is not set
-# CONFIG_BLK_DEV_IT8213 is not set
-# CONFIG_BLK_DEV_IT821X is not set
-# CONFIG_BLK_DEV_NS87415 is not set
-# CONFIG_BLK_DEV_PDC202XX_OLD is not set
-# CONFIG_BLK_DEV_PDC202XX_NEW is not set
-# CONFIG_BLK_DEV_SVWKS is not set
-# CONFIG_BLK_DEV_SIIMAGE is not set
-# CONFIG_BLK_DEV_SL82C105 is not set
-# CONFIG_BLK_DEV_SLC90E66 is not set
-# CONFIG_BLK_DEV_TRM290 is not set
-CONFIG_BLK_DEV_VIA82CXXX=y
-# CONFIG_BLK_DEV_TC86C001 is not set
-CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_IDE is not set
#
# SCSI device support
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
-CONFIG_E1000=y
+# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
# CONFIG_IP1000 is not set
# CONFIG_IGB is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
+# CONFIG_ATL1C is not set
# CONFIG_JME is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_EEPROM_AT24 is not set
-# CONFIG_EEPROM_LEGACY is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
# Special HID drivers
#
CONFIG_HID_COMPAT=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USB_ARCH_HAS_HCD=y
-CONFIG_USB_ARCH_HAS_OHCI=y
-CONFIG_USB_ARCH_HAS_EHCI=y
-# CONFIG_USB is not set
-# CONFIG_USB_OTG_WHITELIST is not set
-# CONFIG_USB_OTG_BLACKLIST_HUB is not set
-
-#
-# Enable Host or Gadget support to see Inventra options
-#
-
-#
-# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# OTG and related infrastructure
-#
+# CONFIG_USB_SUPPORT is not set
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
#
# File systems
#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT2_FS_XIP is not set
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_XATTR=y
-# CONFIG_EXT3_FS_POSIX_ACL is not set
-# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
# CONFIG_EXT4_FS is not set
-CONFIG_JBD=y
-CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
-# CONFIG_JFFS2_FS is not set
-# CONFIG_UBIFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_HIGHMEM is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
PPC_LONG "1b,4b,2b,4b\n" \
".previous" \
: "=&r" (oldval), "=&r" (ret) \
- : "b" (uaddr), "i" (-EFAULT), "1" (oparg) \
+ : "b" (uaddr), "i" (-EFAULT), "r" (oparg) \
: "cr0", "memory")
static inline int futex_atomic_op_inuser (int encoded_op, int __user *uaddr)
switch (op) {
case FUTEX_OP_SET:
- __futex_atomic_op("", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("mr %1,%4\n", ret, oldval, uaddr, oparg);
break;
case FUTEX_OP_ADD:
- __futex_atomic_op("add %1,%0,%1\n", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("add %1,%0,%4\n", ret, oldval, uaddr, oparg);
break;
case FUTEX_OP_OR:
- __futex_atomic_op("or %1,%0,%1\n", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("or %1,%0,%4\n", ret, oldval, uaddr, oparg);
break;
case FUTEX_OP_ANDN:
- __futex_atomic_op("andc %1,%0,%1\n", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("andc %1,%0,%4\n", ret, oldval, uaddr, oparg);
break;
case FUTEX_OP_XOR:
- __futex_atomic_op("xor %1,%0,%1\n", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("xor %1,%0,%4\n", ret, oldval, uaddr, oparg);
break;
default:
ret = -ENOSYS;
*/
#define MMU_FTR_NEED_DTLB_SW_LRU ASM_CONST(0x00200000)
+/* This indicates that the processor uses the wrong opcode for tlbilx
+ * instructions. During the ISA 2.06 development the opcode for tlbilx
+ * changed and some early implementations used to old opcode
+ */
+#define MMU_FTR_TLBILX_EARLY_OPCODE ASM_CONST(0x00400000)
+
#ifndef __ASSEMBLY__
#include <asm/cputable.h>
#define PPC_INST_STSWI 0x7c0005aa
#define PPC_INST_STSWX 0x7c00052a
-#define PPC_INST_TLBILX 0x7c000626
+#define PPC_INST_TLBILX 0x7c000024
+#define PPC_INST_TLBILX_EARLY 0x7c000626
#define PPC_INST_WAIT 0x7c00007c
/* macros to insert fields into opcodes */
#define PPC_RFDI stringify_in_c(.long PPC_INST_RFDI)
#define PPC_RFMCI stringify_in_c(.long PPC_INST_RFMCI)
#define PPC_TLBILX(t, a, b) stringify_in_c(.long PPC_INST_TLBILX | \
- __PPC_T_TLB(t) | __PPC_RA(a) | __PPC_RB(b))
+ __PPC_T_TLB(t) | \
+ __PPC_RA(a) | __PPC_RB(b))
#define PPC_TLBILX_ALL(a, b) PPC_TLBILX(0, a, b)
#define PPC_TLBILX_PID(a, b) PPC_TLBILX(1, a, b)
#define PPC_TLBILX_VA(a, b) PPC_TLBILX(3, a, b)
+
+#define PPC_TLBILX_EARLY(t, a, b) stringify_in_c(.long PPC_INST_TLBILX_EARLY | \
+ __PPC_T_TLB(t) | \
+ __PPC_RA(a) | __PPC_RB(b))
+#define PPC_TLBILX_ALL_EARLY(a, b) PPC_TLBILX_EARLY(0, a, b)
+#define PPC_TLBILX_PID_EARLY(a, b) PPC_TLBILX_EARLY(1, a, b)
+#define PPC_TLBILX_VA_EARLY(a, b) PPC_TLBILX_EARLY(3, a, b)
#define PPC_WAIT(w) stringify_in_c(.long PPC_INST_WAIT | \
__PPC_WC(w))
.cpu_features = CPU_FTRS_E500MC,
.cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
.mmu_features = MMU_FTR_TYPE_FSL_E | MMU_FTR_BIG_PHYS |
- MMU_FTR_USE_TLBILX,
+ MMU_FTR_USE_TLBILX | MMU_FTR_TLBILX_EARLY_OPCODE,
.icache_bsize = 64,
.dcache_bsize = 64,
.num_pmcs = 4,
void flush_tlb_mm(struct mm_struct *mm)
{
- cpumask_t cpu_mask;
unsigned int pid;
preempt_disable();
andi. r3,r3,MMUCSR0_TLBFI@l
bne 1b
MMU_FTR_SECTION_ELSE
- PPC_TLBILX_ALL(0,0)
+ BEGIN_MMU_FTR_SECTION_NESTED(96)
+ PPC_TLBILX_ALL(0,r3)
+ MMU_FTR_SECTION_ELSE_NESTED(96)
+ PPC_TLBILX_ALL_EARLY(0,r3)
+ ALT_MMU_FTR_SECTION_END_NESTED_IFCLR(MMU_FTR_TLBILX_EARLY_OPCODE, 96)
ALT_MMU_FTR_SECTION_END_IFCLR(MMU_FTR_USE_TLBILX)
msync
isync
wrteei 0
mfspr r4,SPRN_MAS6 /* save MAS6 */
mtspr SPRN_MAS6,r3
+ BEGIN_MMU_FTR_SECTION_NESTED(96)
PPC_TLBILX_PID(0,0)
+ MMU_FTR_SECTION_ELSE_NESTED(96)
+ PPC_TLBILX_PID_EARLY(0,0)
+ ALT_MMU_FTR_SECTION_END_NESTED_IFCLR(MMU_FTR_TLBILX_EARLY_OPCODE, 96)
mtspr SPRN_MAS6,r4 /* restore MAS6 */
wrtee r10
MMU_FTR_SECTION_ELSE
mtspr SPRN_MAS1,r4
tlbwe
MMU_FTR_SECTION_ELSE
+ BEGIN_MMU_FTR_SECTION_NESTED(96)
PPC_TLBILX_VA(0,r3)
+ MMU_FTR_SECTION_ELSE_NESTED(96)
+ PPC_TLBILX_VA_EARLY(0,r3)
+ ALT_MMU_FTR_SECTION_END_NESTED_IFCLR(MMU_FTR_TLBILX_EARLY_OPCODE, 96)
ALT_MMU_FTR_SECTION_END_IFCLR(MMU_FTR_USE_TLBILX)
msync
isync
#include <asm/smp.h>
#include <asm/system.h>
#include <asm/uaccess.h>
+#include <asm/firmware.h>
#include "plpar_wrappers.h"
if (!driver)
return;
+ dev->error_state = pci_channel_io_normal;
+
eeh_enable_irq(dev);
if (!driver->err_handler ||
struct vtimer_list *timer;
u64 expires;
} *args = p;
- mod_virt_timer(args->timer, args->expires);
+ mod_virt_timer_periodic(args->timer, args->expires);
}
#define APPLDATA_ADD_TIMER 0
--- /dev/null
+/*
+ * Copyright IBM Corp. 2000,2009
+ * Author(s): Hartmut Penner <hp@de.ibm.com>,
+ * Martin Schwidefsky <schwidefsky@de.ibm.com>
+ * Christian Ehrhardt <ehrhardt@de.ibm.com>
+ */
+
+#ifndef _ASM_S390_CPUID_H_
+#define _ASM_S390_CPUID_H_
+
+/*
+ * CPU type and hardware bug flags. Kept separately for each CPU.
+ * Members of this structure are referenced in head.S, so think twice
+ * before touching them. [mj]
+ */
+
+typedef struct
+{
+ unsigned int version : 8;
+ unsigned int ident : 24;
+ unsigned int machine : 16;
+ unsigned int unused : 16;
+} __attribute__ ((packed)) cpuid_t;
+
+#endif /* _ASM_S390_CPUID_H_ */
#define ASM_KVM_HOST_H
#include <linux/kvm_host.h>
#include <asm/debug.h>
+#include <asm/cpuid.h>
#define KVM_MAX_VCPUS 64
#define KVM_MEMORY_SLOTS 32
#define __LC_USER_EXEC_ASCE 0x02ac
#define __LC_CPUID 0x02b0
#define __LC_INT_CLOCK 0x02c8
+#define __LC_MACHINE_FLAGS 0x02d8
#define __LC_IRB 0x0300
#define __LC_PFAULT_INTPARM 0x0080
#define __LC_CPU_TIMER_SAVE_AREA 0x00d8
#define __LC_CPUID 0x0320
#define __LC_INT_CLOCK 0x0340
#define __LC_VDSO_PER_CPU 0x0350
+#define __LC_MACHINE_FLAGS 0x0358
#define __LC_IRB 0x0380
#define __LC_PASTE 0x03c0
#define __LC_PFAULT_INTPARM 0x11b8
#ifndef __ASSEMBLY__
-#include <asm/processor.h>
+#include <asm/cpuid.h>
+#include <asm/ptrace.h>
#include <linux/types.h>
-#include <asm/sigp.h>
void restart_int_handler(void);
void ext_int_handler(void);
__u32 ext_call_fast; /* 0x02c4 */
__u64 int_clock; /* 0x02c8 */
__u64 clock_comparator; /* 0x02d0 */
- __u8 pad_0x02d8[0x0300-0x02d8]; /* 0x02d8 */
+ __u32 machine_flags; /* 0x02d8 */
+ __u8 pad_0x02dc[0x0300-0x02dc]; /* 0x02dc */
/* Interrupt response block */
__u8 irb[64]; /* 0x0300 */
__u64 int_clock; /* 0x0340 */
__u64 clock_comparator; /* 0x0348 */
__u64 vdso_per_cpu_data; /* 0x0350 */
- __u8 pad_0x0358[0x0380-0x0358]; /* 0x0358 */
+ __u64 machine_flags; /* 0x0358 */
+ __u8 pad_0x0360[0x0380-0x0360]; /* 0x0360 */
/* Interrupt response block. */
__u8 irb[64]; /* 0x0380 */
#define __ASM_S390_PROCESSOR_H
#include <linux/linkage.h>
+#include <asm/cpuid.h>
+#include <asm/page.h>
#include <asm/ptrace.h>
+#include <asm/setup.h>
#ifdef __KERNEL__
/*
*/
#define current_text_addr() ({ void *pc; asm("basr %0,0" : "=a" (pc)); pc; })
-/*
- * CPU type and hardware bug flags. Kept separately for each CPU.
- * Members of this structure are referenced in head.S, so think twice
- * before touching them. [mj]
- */
-
-typedef struct
-{
- unsigned int version : 8;
- unsigned int ident : 24;
- unsigned int machine : 16;
- unsigned int unused : 16;
-} __attribute__ ((packed)) cpuid_t;
-
static inline void get_cpu_id(cpuid_t *ptr)
{
asm volatile("stidp 0(%1)" : "=m" (*ptr) : "a" (ptr));
#ifdef __KERNEL__
-#include <asm/setup.h>
-#include <asm/page.h>
/*
* The pt_regs struct defines the way the registers are stored on
#ifdef __KERNEL__
+#include <asm/lowcore.h>
#include <asm/types.h>
#define PARMAREA 0x10400
/*
* Machine features detected in head.S
*/
-extern unsigned long machine_flags;
#define MACHINE_FLAG_VM (1UL << 0)
#define MACHINE_FLAG_IEEE (1UL << 1)
#define MACHINE_FLAG_HPAGE (1UL << 10)
#define MACHINE_FLAG_PFMF (1UL << 11)
-#define MACHINE_IS_VM (machine_flags & MACHINE_FLAG_VM)
-#define MACHINE_IS_KVM (machine_flags & MACHINE_FLAG_KVM)
-#define MACHINE_HAS_DIAG9C (machine_flags & MACHINE_FLAG_DIAG9C)
+#define MACHINE_IS_VM (S390_lowcore.machine_flags & MACHINE_FLAG_VM)
+#define MACHINE_IS_KVM (S390_lowcore.machine_flags & MACHINE_FLAG_KVM)
+#define MACHINE_HAS_DIAG9C (S390_lowcore.machine_flags & MACHINE_FLAG_DIAG9C)
#ifndef __s390x__
-#define MACHINE_HAS_IEEE (machine_flags & MACHINE_FLAG_IEEE)
-#define MACHINE_HAS_CSP (machine_flags & MACHINE_FLAG_CSP)
+#define MACHINE_HAS_IEEE (S390_lowcore.machine_flags & MACHINE_FLAG_IEEE)
+#define MACHINE_HAS_CSP (S390_lowcore.machine_flags & MACHINE_FLAG_CSP)
#define MACHINE_HAS_IDTE (0)
#define MACHINE_HAS_DIAG44 (1)
-#define MACHINE_HAS_MVPG (machine_flags & MACHINE_FLAG_MVPG)
+#define MACHINE_HAS_MVPG (S390_lowcore.machine_flags & MACHINE_FLAG_MVPG)
#define MACHINE_HAS_MVCOS (0)
#define MACHINE_HAS_HPAGE (0)
#define MACHINE_HAS_PFMF (0)
#else /* __s390x__ */
#define MACHINE_HAS_IEEE (1)
#define MACHINE_HAS_CSP (1)
-#define MACHINE_HAS_IDTE (machine_flags & MACHINE_FLAG_IDTE)
-#define MACHINE_HAS_DIAG44 (machine_flags & MACHINE_FLAG_DIAG44)
+#define MACHINE_HAS_IDTE (S390_lowcore.machine_flags & MACHINE_FLAG_IDTE)
+#define MACHINE_HAS_DIAG44 (S390_lowcore.machine_flags & MACHINE_FLAG_DIAG44)
#define MACHINE_HAS_MVPG (1)
-#define MACHINE_HAS_MVCOS (machine_flags & MACHINE_FLAG_MVCOS)
-#define MACHINE_HAS_HPAGE (machine_flags & MACHINE_FLAG_HPAGE)
-#define MACHINE_HAS_PFMF (machine_flags & MACHINE_FLAG_PFMF)
+#define MACHINE_HAS_MVCOS (S390_lowcore.machine_flags & MACHINE_FLAG_MVCOS)
+#define MACHINE_HAS_HPAGE (S390_lowcore.machine_flags & MACHINE_FLAG_HPAGE)
+#define MACHINE_HAS_PFMF (S390_lowcore.machine_flags & MACHINE_FLAG_PFMF)
#endif /* __s390x__ */
#define ZFCPDUMP_HSA_SIZE (32UL<<20)
#define ASYNC_SIZE (PAGE_SIZE << ASYNC_ORDER)
#ifndef __ASSEMBLY__
-#include <asm/processor.h>
#include <asm/lowcore.h>
+#include <asm/page.h>
+#include <asm/processor.h>
/*
* low level task data that entry.S needs immediate access to
extern void add_virt_timer(void *new);
extern void add_virt_timer_periodic(void *new);
extern int mod_virt_timer(struct vtimer_list *timer, __u64 expires);
+extern int mod_virt_timer_periodic(struct vtimer_list *timer, __u64 expires);
extern int del_virt_timer(struct vtimer_list *timer);
extern void init_cpu_vtimer(void);
#ifndef _ASM_S390_TIMEX_H
#define _ASM_S390_TIMEX_H
+/* The value of the TOD clock for 1.1.1970. */
+#define TOD_UNIX_EPOCH 0x7d91048bca000000ULL
+
/* Inline functions for clock register access. */
static inline int set_clock(__u64 time)
{
void init_cpu_timer(void);
unsigned long long monotonic_clock(void);
+extern u64 sched_clock_base_cc;
+
#endif
#define __NR_pipe2 325
#define __NR_dup3 326
#define __NR_epoll_create1 327
-#define NR_syscalls 328
+#define __NR_preadv 328
+#define __NR_pwritev 329
+#define NR_syscalls 330
/*
* There are some system calls that are not present on 64 bit, some
DEFINE(__TI_flags, offsetof(struct thread_info, flags));
DEFINE(__TI_cpu, offsetof(struct thread_info, cpu));
DEFINE(__TI_precount, offsetof(struct thread_info, preempt_count));
+ DEFINE(__TI_user_timer, offsetof(struct thread_info, user_timer));
+ DEFINE(__TI_system_timer, offsetof(struct thread_info, system_timer));
BLANK();
DEFINE(__PT_ARGS, offsetof(struct pt_regs, args));
DEFINE(__PT_PSW, offsetof(struct pt_regs, psw));
llgfr %r5,%r5 # u32
llgfr %r6,%r6 # u32
jg compat_sys_keyctl # branch to system call
+
+ .globl compat_sys_preadv_wrapper
+compat_sys_preadv_wrapper:
+ llgfr %r2,%r2 # unsigned long
+ llgtr %r3,%r3 # compat_iovec *
+ llgfr %r4,%r4 # unsigned long
+ llgfr %r5,%r5 # u32
+ llgfr %r6,%r6 # u32
+ jg compat_sys_preadv # branch to system call
+
+ .globl compat_sys_pwritev_wrapper
+compat_sys_pwritev_wrapper:
+ llgfr %r2,%r2 # unsigned long
+ llgtr %r3,%r3 # compat_iovec *
+ llgfr %r4,%r4 # unsigned long
+ llgfr %r5,%r5 # u32
+ llgfr %r6,%r6 # u32
+ jg compat_sys_pwritev # branch to system call
char kernel_nss_name[NSS_NAME_SIZE + 1];
+static unsigned long machine_flags;
+
static void __init setup_boot_command_line(void);
+/*
+ * Get the TOD clock running.
+ */
+static void __init reset_tod_clock(void)
+{
+ u64 time;
+
+ if (store_clock(&time) == 0)
+ return;
+ /* TOD clock not running. Set the clock to Unix Epoch. */
+ if (set_clock(TOD_UNIX_EPOCH) != 0 || store_clock(&time) != 0)
+ disabled_wait(0);
+
+ sched_clock_base_cc = TOD_UNIX_EPOCH;
+}
#ifdef CONFIG_SHARED_KERNEL
int __init savesys_ipl_nss(char *cmd, const int cmdlen);
*/
void __init startup_init(void)
{
+ reset_tod_clock();
ipl_save_parameters();
rescue_initrd();
clear_bss_section();
setup_hpage();
sclp_facilities_detect();
detect_memory_layout(memory_chunk);
+ S390_lowcore.machine_flags = machine_flags;
lockdep_on();
}
__CPUINIT
.globl restart_int_handler
restart_int_handler:
+ basr %r1,0
+restart_base:
+ spt restart_vtime-restart_base(%r1)
+ stck __LC_LAST_UPDATE_CLOCK
+ mvc __LC_LAST_UPDATE_TIMER(8),restart_vtime-restart_base(%r1)
+ mvc __LC_EXIT_TIMER(8),restart_vtime-restart_base(%r1)
l %r15,__LC_SAVE_AREA+60 # load ksp
lctl %c0,%c15,__LC_CREGS_SAVE_AREA # get new ctl regs
lam %a0,%a15,__LC_AREGS_SAVE_AREA
lm %r6,%r15,__SF_GPRS(%r15) # load registers from clone
+ l %r1,__LC_THREAD_INFO
+ mvc __LC_USER_TIMER(8),__TI_user_timer(%r1)
+ mvc __LC_SYSTEM_TIMER(8),__TI_system_timer(%r1)
+ xc __LC_STEAL_TIMER(8),__LC_STEAL_TIMER
stosm __SF_EMPTY(%r15),0x04 # now we can turn dat on
basr %r14,0
l %r14,restart_addr-.(%r14)
br %r14 # branch to start_secondary
restart_addr:
.long start_secondary
+ .align 8
+restart_vtime:
+ .long 0x7fffffff,0xffffffff
.previous
#else
/*
__CPUINIT
.globl restart_int_handler
restart_int_handler:
+ basr %r1,0
+restart_base:
+ spt restart_vtime-restart_base(%r1)
+ stck __LC_LAST_UPDATE_CLOCK
+ mvc __LC_LAST_UPDATE_TIMER(8),restart_vtime-restart_base(%r1)
+ mvc __LC_EXIT_TIMER(8),restart_vtime-restart_base(%r1)
lg %r15,__LC_SAVE_AREA+120 # load ksp
lghi %r10,__LC_CREGS_SAVE_AREA
lctlg %c0,%c15,0(%r10) # get new ctl regs
lghi %r10,__LC_AREGS_SAVE_AREA
lam %a0,%a15,0(%r10)
lmg %r6,%r15,__SF_GPRS(%r15) # load registers from clone
+ lg %r1,__LC_THREAD_INFO
+ mvc __LC_USER_TIMER(8),__TI_user_timer(%r1)
+ mvc __LC_SYSTEM_TIMER(8),__TI_system_timer(%r1)
+ xc __LC_STEAL_TIMER(8),__LC_STEAL_TIMER
stosm __SF_EMPTY(%r15),0x04 # now we can turn dat on
jg start_secondary
+ .align 8
+restart_vtime:
+ .long 0x7fffffff,0xffffffff
.previous
#else
/*
.LPG0:
xc 0x200(256),0x200 # partially clear lowcore
xc 0x300(256),0x300
-
+ l %r1,5f-.LPG0(%r13)
+ stck 0(%r1)
+ spt 6f-.LPG0(%r13)
+ mvc __LC_LAST_UPDATE_CLOCK(8),0(%r1)
+ mvc __LC_LAST_UPDATE_TIMER(8),6f-.LPG0(%r13)
+ mvc __LC_EXIT_TIMER(8),5f-.LPG0(%r13)
#ifndef CONFIG_MARCH_G5
# check processor version against MARCH_{G5,Z900,Z990,Z9_109,Z10}
stidp __LC_CPUID # store cpuid
brct %r0,0b
#endif
- l %r13,0f-.LPG0(%r13)
+ l %r13,4f-.LPG0(%r13)
b 0(%r13)
-0: .long startup_continue
+ .align 4
+4: .long startup_continue
+5: .long sched_clock_base_cc
+ .align 8
+6: .long 0x7fffffff,0xffffffff
#
# params at 10400 (setup.h)
#include <linux/init.h>
#include <linux/errno.h>
+#include <linux/hardirq.h>
#include <linux/time.h>
#include <linux/module.h>
#include <asm/lowcore.h>
struct mci *mci;
int umode;
- lockdep_off();
+ nmi_enter();
s390_idle_check();
mci = (struct mci *) &S390_lowcore.mcck_interruption_code;
mcck->warning = 1;
set_thread_flag(TIF_MCCK_PENDING);
}
- lockdep_on();
+ nmi_exit();
}
static int __init machine_check_init(void)
unsigned int console_irq = -1;
EXPORT_SYMBOL(console_irq);
-unsigned long machine_flags;
-EXPORT_SYMBOL(machine_flags);
-
unsigned long elf_hwcap = 0;
char elf_platform[ELF_PLATFORM_SIZE];
__alloc_bootmem(PAGE_SIZE, PAGE_SIZE, 0) + PAGE_SIZE;
lc->current_task = (unsigned long) init_thread_union.thread_info.task;
lc->thread_info = (unsigned long) &init_thread_union;
+ lc->machine_flags = S390_lowcore.machine_flags;
#ifndef CONFIG_64BIT
if (MACHINE_HAS_IEEE) {
lc->extended_save_area_addr = (__u32)
#else
lc->vdso_per_cpu_data = (unsigned long) &lc->paste[0];
#endif
+ lc->sync_enter_timer = S390_lowcore.sync_enter_timer;
+ lc->async_enter_timer = S390_lowcore.async_enter_timer;
+ lc->exit_timer = S390_lowcore.exit_timer;
+ lc->user_timer = S390_lowcore.user_timer;
+ lc->system_timer = S390_lowcore.system_timer;
+ lc->steal_timer = S390_lowcore.steal_timer;
+ lc->last_update_timer = S390_lowcore.last_update_timer;
+ lc->last_update_clock = S390_lowcore.last_update_clock;
set_prefix((u32)(unsigned long) lc);
lowcore_ptr[0] = lc;
}
cpu_lowcore->current_task = (unsigned long) idle;
cpu_lowcore->cpu_nr = cpu;
cpu_lowcore->kernel_asce = S390_lowcore.kernel_asce;
+ cpu_lowcore->machine_flags = S390_lowcore.machine_flags;
eieio();
while (signal_processor(cpu, sigp_restart) == sigp_busy)
int pcpus, cpu;
pcpus = simple_strtoul(s, NULL, 0);
- for (cpu = 0; cpu < pcpus && cpu < nr_cpu_ids; cpu++)
+ init_cpu_possible(cpumask_of(0));
+ for (cpu = 1; cpu < pcpus && cpu < nr_cpu_ids; cpu++)
set_cpu_possible(cpu, true);
return 0;
}
SYSCALL(sys_pipe2,sys_pipe2,sys_pipe2_wrapper) /* 325 */
SYSCALL(sys_dup3,sys_dup3,sys_dup3_wrapper)
SYSCALL(sys_epoll_create1,sys_epoll_create1,sys_epoll_create1_wrapper)
+SYSCALL(sys_preadv,sys_preadv,compat_sys_preadv_wrapper)
+SYSCALL(sys_pwritev,sys_pwritev,compat_sys_pwritev_wrapper)
#define USECS_PER_JIFFY ((unsigned long) 1000000/HZ)
#define CLK_TICKS_PER_JIFFY ((unsigned long) USECS_PER_JIFFY << 12)
-/* The value of the TOD clock for 1.1.1970. */
-#define TOD_UNIX_EPOCH 0x7d91048bca000000ULL
-
/*
* Create a small time difference between the timer interrupts
* on the different cpus to avoid lock contention.
#define TICK_SIZE tick
+u64 sched_clock_base_cc = -1; /* Force to data section. */
+
static ext_int_info_t ext_int_info_cc;
static ext_int_info_t ext_int_etr_cc;
-static u64 sched_clock_base_cc;
static DEFINE_PER_CPU(struct clock_event_device, comparators);
static void etr_reset(void);
static void stp_reset(void);
-/*
- * Get the TOD clock running.
- */
-static u64 __init reset_tod_clock(void)
+unsigned long read_persistent_clock(void)
{
- u64 time;
-
- etr_reset();
- stp_reset();
- if (store_clock(&time) == 0)
- return time;
- /* TOD clock not running. Set the clock to Unix Epoch. */
- if (set_clock(TOD_UNIX_EPOCH) != 0 || store_clock(&time) != 0)
- panic("TOD clock not operational.");
+ struct timespec ts;
- return TOD_UNIX_EPOCH;
+ tod_to_timeval(get_clock() - TOD_UNIX_EPOCH, &ts);
+ return ts.tv_sec;
}
static cycle_t read_tod_clock(void)
*/
void __init time_init(void)
{
- sched_clock_base_cc = reset_tod_clock();
+ struct timespec ts;
+ unsigned long flags;
+ cycle_t now;
- /* set xtime */
- tod_to_timeval(sched_clock_base_cc - TOD_UNIX_EPOCH, &xtime);
- set_normalized_timespec(&wall_to_monotonic,
- -xtime.tv_sec, -xtime.tv_nsec);
+ /* Reset time synchronization interfaces. */
+ etr_reset();
+ stp_reset();
/* request the clock comparator external interrupt */
if (register_early_external_interrupt(0x1004,
&ext_int_info_cc) != 0)
panic("Couldn't request external interrupt 0x1004");
- if (clocksource_register(&clocksource_tod) != 0)
- panic("Could not register TOD clock source");
-
/* request the timing alert external interrupt */
if (register_early_external_interrupt(0x1406,
timing_alert_interrupt,
&ext_int_etr_cc) != 0)
panic("Couldn't request external interrupt 0x1406");
+ if (clocksource_register(&clocksource_tod) != 0)
+ panic("Could not register TOD clock source");
+
+ /*
+ * The TOD clock is an accurate clock. The xtime should be
+ * initialized in a way that the difference between TOD and
+ * xtime is reasonably small. Too bad that timekeeping_init
+ * sets xtime.tv_nsec to zero. In addition the clock source
+ * change from the jiffies clock source to the TOD clock
+ * source add another error of up to 1/HZ second. The same
+ * function sets wall_to_monotonic to a value that is too
+ * small for /proc/uptime to be accurate.
+ * Reset xtime and wall_to_monotonic to sane values.
+ */
+ write_seqlock_irqsave(&xtime_lock, flags);
+ now = get_clock();
+ tod_to_timeval(now - TOD_UNIX_EPOCH, &xtime);
+ clocksource_tod.cycle_last = now;
+ clocksource_tod.raw_time = xtime;
+ tod_to_timeval(sched_clock_base_cc - TOD_UNIX_EPOCH, &ts);
+ set_normalized_timespec(&wall_to_monotonic, -ts.tv_sec, -ts.tv_nsec);
+ write_sequnlock_irqrestore(&xtime_lock, flags);
+
/* Enable TOD clock interrupts on the boot cpu. */
init_cpu_timer();
+
/* Enable cpu timer interrupts on the boot cpu. */
vtime_init();
}
static void stp_work_fn(struct work_struct *work);
static DEFINE_MUTEX(stp_work_mutex);
static DECLARE_WORK(stp_work, stp_work_fn);
+static struct timer_list stp_timer;
static int __init early_parse_stp(char *p)
{
}
}
+static void stp_timeout(unsigned long dummy)
+{
+ queue_work(time_sync_wq, &stp_work);
+}
+
static int __init stp_init(void)
{
if (!test_bit(CLOCK_SYNC_HAS_STP, &clock_sync_flags))
return 0;
+ setup_timer(&stp_timer, stp_timeout, 0UL);
time_init_wq();
if (!stp_online)
return 0;
if (!stp_online) {
chsc_sstpc(stp_page, STP_OP_CTRL, 0x0000);
+ del_timer_sync(&stp_timer);
goto out_unlock;
}
stop_machine(stp_sync_clock, &stp_sync, &cpu_online_map);
put_online_cpus();
+ if (!check_sync_clock())
+ /*
+ * There is a usable clock but the synchonization failed.
+ * Retry after a second.
+ */
+ mod_timer(&stp_timer, jiffies + HZ);
+
out_unlock:
mutex_unlock(&stp_work_mutex);
}
/* Account time spent with enabled wait psw loaded as idle time. */
idle_time = S390_lowcore.int_clock - idle->idle_enter;
account_idle_time(idle_time);
+ S390_lowcore.steal_timer +=
+ idle->idle_enter - S390_lowcore.last_update_clock;
S390_lowcore.last_update_clock = S390_lowcore.int_clock;
/* Account system time spent going idle. */
}
EXPORT_SYMBOL(add_virt_timer_periodic);
-/*
- * If we change a pending timer the function must be called on the CPU
- * where the timer is running on, e.g. by smp_call_function_single()
- *
- * The original mod_timer adds the timer if it is not pending. For
- * compatibility we do the same. The timer will be added on the current
- * CPU as a oneshot timer.
- *
- * returns whether it has modified a pending timer (1) or not (0)
- */
-int mod_virt_timer(struct vtimer_list *timer, __u64 expires)
+int __mod_vtimer(struct vtimer_list *timer, __u64 expires, int periodic)
{
struct vtimer_queue *vq;
unsigned long flags;
BUG_ON(!timer->function);
BUG_ON(!expires || expires > VTIMER_MAX_SLICE);
- /*
- * This is a common optimization triggered by the
- * networking code - if the timer is re-modified
- * to be the same thing then just return:
- */
if (timer->expires == expires && vtimer_pending(timer))
return 1;
cpu = get_cpu();
vq = &per_cpu(virt_cpu_timer, cpu);
- /* check if we run on the right CPU */
- BUG_ON(timer->cpu != cpu);
-
/* disable interrupts before test if timer is pending */
spin_lock_irqsave(&vq->lock, flags);
/* if timer isn't pending add it on the current CPU */
if (!vtimer_pending(timer)) {
spin_unlock_irqrestore(&vq->lock, flags);
- /* we do not activate an interval timer with mod_virt_timer */
- timer->interval = 0;
+
+ if (periodic)
+ timer->interval = expires;
+ else
+ timer->interval = 0;
timer->expires = expires;
timer->cpu = cpu;
internal_add_vtimer(timer);
return 0;
}
+ /* check if we run on the right CPU */
+ BUG_ON(timer->cpu != cpu);
+
list_del_init(&timer->entry);
timer->expires = expires;
-
- /* also change the interval if we have an interval timer */
- if (timer->interval)
+ if (periodic)
timer->interval = expires;
/* the timer can't expire anymore so we can release the lock */
internal_add_vtimer(timer);
return 1;
}
+
+/*
+ * If we change a pending timer the function must be called on the CPU
+ * where the timer is running on.
+ *
+ * returns whether it has modified a pending timer (1) or not (0)
+ */
+int mod_virt_timer(struct vtimer_list *timer, __u64 expires)
+{
+ return __mod_vtimer(timer, expires, 0);
+}
EXPORT_SYMBOL(mod_virt_timer);
/*
+ * If we change a pending timer the function must be called on the CPU
+ * where the timer is running on.
+ *
+ * returns whether it has modified a pending timer (1) or not (0)
+ */
+int mod_virt_timer_periodic(struct vtimer_list *timer, __u64 expires)
+{
+ return __mod_vtimer(timer, expires, 1);
+}
+EXPORT_SYMBOL(mod_virt_timer_periodic);
+
+/*
* delete a virtual timer
*
* returns whether the deleted timer was pending (1) or not (0)
*/
void init_cpu_vtimer(void)
{
- struct thread_info *ti = current_thread_info();
struct vtimer_queue *vq;
- S390_lowcore.user_timer = ti->user_timer;
- S390_lowcore.system_timer = ti->system_timer;
-
- /* kick the virtual timer */
- asm volatile ("STCK %0" : "=m" (S390_lowcore.last_update_clock));
- asm volatile ("STPT %0" : "=m" (S390_lowcore.last_update_timer));
-
/* initialize per cpu vtimer structure */
vq = &__get_cpu_var(virt_cpu_timer);
INIT_LIST_HEAD(&vq->list);
#ifdef __KERNEL__
+#include <asm/system.h>
+
#define ATOMIC_INIT(i) { (i) }
extern int __atomic_add_return(int, atomic_t *);
free_queue(lp->tx_num_entries, lp->tx_base);
out_free_mssbuf:
- if (mssbuf)
- kfree(mssbuf);
+ kfree(mssbuf);
out_free_iommu:
ldc_iommu_release(lp);
hlist_del(&lp->list);
- if (lp->mssbuf)
- kfree(lp->mssbuf);
+ kfree(lp->mssbuf);
ldc_iommu_release(lp);
while (!cpu_isset(cpuid, smp_commenced_mask))
rmb();
- ipi_call_lock();
+ ipi_call_lock_irq();
cpu_set(cpuid, cpu_online_map);
- ipi_call_unlock();
+ ipi_call_unlock_irq();
/* idle thread is expected to have preempt disabled */
preempt_disable();
bool "SGI Ultraviolet"
depends on X86_64
depends on X86_EXTENDED_PLATFORM
+ depends on NUMA
select X86_X2APIC
---help---
This option is needed in order to support SGI Ultraviolet systems.
bool "Branch Trace Store"
default y
depends on X86_DEBUGCTLMSR
+ depends on BROKEN
---help---
This adds a ptrace interface to the hardware's branch trace store.
#define LHCALL_FLUSH_ASYNC 0
#define LHCALL_LGUEST_INIT 1
#define LHCALL_SHUTDOWN 2
-#define LHCALL_LOAD_GDT 3
#define LHCALL_NEW_PGTABLE 4
#define LHCALL_FLUSH_TLB 5
#define LHCALL_LOAD_IDT_ENTRY 6
#define LHCALL_SET_PMD 15
#define LHCALL_LOAD_TLS 16
#define LHCALL_NOTIFY 17
+#define LHCALL_LOAD_GDT_ENTRY 18
#define LGUEST_TRAP_ENTRY 0x1F
extern int kernel_map_sync_memtype(u64 base, unsigned long size,
unsigned long flag);
-extern void map_devmem(unsigned long pfn, unsigned long size,
- struct pgprot vma_prot);
-extern void unmap_devmem(unsigned long pfn, unsigned long size,
- struct pgprot vma_prot);
#endif /* _ASM_X86_PAT_H */
/* ========================================================================= */
/* UVH_BAU_DATA_CONFIG */
/* ========================================================================= */
+#define UVH_LB_BAU_MISC_CONTROL 0x320170UL
+#define UV_ENABLE_INTD_SOFT_ACK_MODE_SHIFT 15
+#define UV_INTD_SOFT_ACK_TIMEOUT_PERIOD_SHIFT 16
+#define UV_INTD_SOFT_ACK_TIMEOUT_PERIOD 0x000000000bUL
+/* 1011 timebase 7 (168millisec) * 3 ticks -> 500ms */
#define UVH_BAU_DATA_CONFIG 0x61680UL
#define UVH_BAU_DATA_CONFIG_32 0x0438
unsigned long gnode_upper, lowmem_redir_base, lowmem_redir_size;
int bytes, nid, cpu, lcpu, pnode, blade, i, j, m_val, n_val;
int max_pnode = 0;
- unsigned long mmr_base, present;
+ unsigned long mmr_base, present, paddr;
+ unsigned short pnode_mask;
map_low_mmrs();
}
}
+ pnode_mask = (1 << n_val) - 1;
node_id.v = uv_read_local_mmr(UVH_NODE_ID);
gnode_upper = (((unsigned long)node_id.s.node_id) &
~((1 << n_val) - 1)) << m_val;
uv_cpu_hub_info(cpu)->numa_blade_id = blade;
uv_cpu_hub_info(cpu)->blade_processor_id = lcpu;
uv_cpu_hub_info(cpu)->pnode = pnode;
- uv_cpu_hub_info(cpu)->pnode_mask = (1 << n_val) - 1;
+ uv_cpu_hub_info(cpu)->pnode_mask = pnode_mask;
uv_cpu_hub_info(cpu)->gpa_mask = (1 << (m_val + n_val)) - 1;
uv_cpu_hub_info(cpu)->gnode_upper = gnode_upper;
uv_cpu_hub_info(cpu)->global_mmr_base = mmr_base;
lcpu, blade);
}
+ /* Add blade/pnode info for nodes without cpus */
+ for_each_online_node(nid) {
+ if (uv_node_to_blade[nid] >= 0)
+ continue;
+ paddr = node_start_pfn(nid) << PAGE_SHIFT;
+ pnode = (paddr >> m_val) & pnode_mask;
+ blade = boot_pnode_to_blade(pnode);
+ uv_node_to_blade[nid] = blade;
+ }
+
map_gru_high(max_pnode);
map_mmr_high(max_pnode);
map_config_high(max_pnode);
memcpy(&uv_systab, tab, sizeof(struct uv_systab));
iounmap(tab);
- printk(KERN_INFO "EFI UV System Table Revision %d\n", tab->revision);
+ printk(KERN_INFO "EFI UV System Table Revision %d\n",
+ uv_systab.revision);
}
#else /* !CONFIG_EFI */
static void drv_write(struct drv_cmd *cmd)
{
+ int this_cpu;
+
+ this_cpu = get_cpu();
+ if (cpumask_test_cpu(this_cpu, cmd->mask))
+ do_drv_write(cmd);
smp_call_function_many(cmd->mask, do_drv_write, cmd, 1);
+ put_cpu();
}
static u32 get_cur_val(const struct cpumask *mask)
return err;
err = microcode_init_cpu(cpu);
- if (err)
- sysfs_remove_group(&sys_dev->kobj, &mc_attr_group);
return err;
}
return swiotlb_alloc_coherent(hwdev, size, dma_handle, flags);
}
-struct dma_map_ops swiotlb_dma_ops = {
+static struct dma_map_ops swiotlb_dma_ops = {
.mapping_error = swiotlb_dma_mapping_error,
.alloc_coherent = x86_swiotlb_alloc_coherent,
.free_coherent = swiotlb_free_coherent,
/* position of pnode (which is nasid>>1): */
static int uv_nshift __read_mostly;
+/* base pnode in this partition */
+static int uv_partition_base_pnode __read_mostly;
static unsigned long uv_mmask __read_mostly;
static DEFINE_PER_CPU(struct bau_control, bau_control);
/*
+ * Determine the first node on a blade.
+ */
+static int __init blade_to_first_node(int blade)
+{
+ int node, b;
+
+ for_each_online_node(node) {
+ b = uv_node_to_blade_id(node);
+ if (blade == b)
+ return node;
+ }
+ return -1; /* shouldn't happen */
+}
+
+/*
+ * Determine the apicid of the first cpu on a blade.
+ */
+static int __init blade_to_first_apicid(int blade)
+{
+ int cpu;
+
+ for_each_present_cpu(cpu)
+ if (blade == uv_cpu_to_blade_id(cpu))
+ return per_cpu(x86_cpu_to_apicid, cpu);
+ return -1;
+}
+
+/*
* Free a software acknowledge hardware resource by clearing its Pending
* bit. This will return a reply to the sender.
* If the message has timed out, a reply has already been sent by the
msp = __get_cpu_var(bau_control).msg_statuses + msg_slot;
cpu = uv_blade_processor_id();
msg->number_of_cpus =
- uv_blade_nr_online_cpus(uv_node_to_blade_id(numa_node_id()));
+ uv_blade_nr_online_cpus(uv_node_to_blade_id(numa_node_id()));
this_cpu_mask = 1UL << cpu;
if (msp->seen_by.bits & this_cpu_mask)
return;
* Returns @flush_mask if some remote flushing remains to be done. The
* mask will have some bits still set.
*/
-const struct cpumask *uv_flush_send_and_wait(int cpu, int this_blade,
+const struct cpumask *uv_flush_send_and_wait(int cpu, int this_pnode,
struct bau_desc *bau_desc,
struct cpumask *flush_mask)
{
int completion_status = 0;
int right_shift;
int tries = 0;
- int blade;
+ int pnode;
int bit;
unsigned long mmr_offset;
unsigned long index;
* use the IPI method of shootdown on them.
*/
for_each_cpu(bit, flush_mask) {
- blade = uv_cpu_to_blade_id(bit);
- if (blade == this_blade)
+ pnode = uv_cpu_to_pnode(bit);
+ if (pnode == this_pnode)
continue;
cpumask_clear_cpu(bit, flush_mask);
}
struct cpumask *flush_mask = __get_cpu_var(uv_flush_tlb_mask);
int i;
int bit;
- int blade;
+ int pnode;
int uv_cpu;
- int this_blade;
+ int this_pnode;
int locals = 0;
struct bau_desc *bau_desc;
cpumask_andnot(flush_mask, cpumask, cpumask_of(cpu));
uv_cpu = uv_blade_processor_id();
- this_blade = uv_numa_blade_id();
+ this_pnode = uv_hub_info->pnode;
bau_desc = __get_cpu_var(bau_control).descriptor_base;
bau_desc += UV_ITEMS_PER_DESCRIPTOR * uv_cpu;
i = 0;
for_each_cpu(bit, flush_mask) {
- blade = uv_cpu_to_blade_id(bit);
- BUG_ON(blade > (UV_DISTRIBUTION_SIZE - 1));
- if (blade == this_blade) {
+ pnode = uv_cpu_to_pnode(bit);
+ BUG_ON(pnode > (UV_DISTRIBUTION_SIZE - 1));
+ if (pnode == this_pnode) {
locals++;
continue;
}
- bau_node_set(blade, &bau_desc->distribution);
+ bau_node_set(pnode - uv_partition_base_pnode,
+ &bau_desc->distribution);
i++;
}
if (i == 0) {
bau_desc->payload.address = va;
bau_desc->payload.sending_cpu = cpu;
- return uv_flush_send_and_wait(uv_cpu, this_blade, bau_desc, flush_mask);
+ return uv_flush_send_and_wait(uv_cpu, this_pnode, bau_desc, flush_mask);
}
/*
set_irq_regs(old_regs);
}
+/*
+ * uv_enable_timeouts
+ *
+ * Each target blade (i.e. blades that have cpu's) needs to have
+ * shootdown message timeouts enabled. The timeout does not cause
+ * an interrupt, but causes an error message to be returned to
+ * the sender.
+ */
static void uv_enable_timeouts(void)
{
- int i;
int blade;
- int last_blade;
+ int nblades;
int pnode;
- int cur_cpu = 0;
- unsigned long apicid;
+ unsigned long mmr_image;
- last_blade = -1;
- for_each_online_node(i) {
- blade = uv_node_to_blade_id(i);
- if (blade == last_blade)
+ nblades = uv_num_possible_blades();
+
+ for (blade = 0; blade < nblades; blade++) {
+ if (!uv_blade_nr_possible_cpus(blade))
continue;
- last_blade = blade;
- apicid = per_cpu(x86_cpu_to_apicid, cur_cpu);
+
pnode = uv_blade_to_pnode(blade);
- cur_cpu += uv_blade_nr_possible_cpus(i);
+ mmr_image =
+ uv_read_global_mmr64(pnode, UVH_LB_BAU_MISC_CONTROL);
+ /*
+ * Set the timeout period and then lock it in, in three
+ * steps; captures and locks in the period.
+ *
+ * To program the period, the SOFT_ACK_MODE must be off.
+ */
+ mmr_image &= ~((unsigned long)1 <<
+ UV_ENABLE_INTD_SOFT_ACK_MODE_SHIFT);
+ uv_write_global_mmr64
+ (pnode, UVH_LB_BAU_MISC_CONTROL, mmr_image);
+ /*
+ * Set the 4-bit period.
+ */
+ mmr_image &= ~((unsigned long)0xf <<
+ UV_INTD_SOFT_ACK_TIMEOUT_PERIOD_SHIFT);
+ mmr_image |= (UV_INTD_SOFT_ACK_TIMEOUT_PERIOD <<
+ UV_INTD_SOFT_ACK_TIMEOUT_PERIOD_SHIFT);
+ uv_write_global_mmr64
+ (pnode, UVH_LB_BAU_MISC_CONTROL, mmr_image);
+ /*
+ * Subsequent reversals of the timebase bit (3) cause an
+ * immediate timeout of one or all INTD resources as
+ * indicated in bits 2:0 (7 causes all of them to timeout).
+ */
+ mmr_image |= ((unsigned long)1 <<
+ UV_ENABLE_INTD_SOFT_ACK_MODE_SHIFT);
+ uv_write_global_mmr64
+ (pnode, UVH_LB_BAU_MISC_CONTROL, mmr_image);
}
}
stat->requestee, stat->onetlb, stat->alltlb,
stat->s_retry, stat->d_retry, stat->ptc_i);
seq_printf(file, "%lx %ld %ld %ld %ld %ld %ld\n",
- uv_read_global_mmr64(uv_blade_to_pnode
- (uv_cpu_to_blade_id(cpu)),
+ uv_read_global_mmr64(uv_cpu_to_pnode(cpu),
UVH_LB_BAU_INTD_SOFTWARE_ACKNOWLEDGE),
stat->sflush, stat->dflush,
stat->retriesok, stat->nomsg,
* finish the initialization of the per-blade control structures
*/
static void __init
-uv_table_bases_finish(int blade, int node, int cur_cpu,
+uv_table_bases_finish(int blade,
struct bau_control *bau_tablesp,
struct bau_desc *adp)
{
struct bau_control *bcp;
- int i;
+ int cpu;
- for (i = cur_cpu; i < cur_cpu + uv_blade_nr_possible_cpus(blade); i++) {
- bcp = (struct bau_control *)&per_cpu(bau_control, i);
+ for_each_present_cpu(cpu) {
+ if (blade != uv_cpu_to_blade_id(cpu))
+ continue;
+ bcp = (struct bau_control *)&per_cpu(bau_control, cpu);
bcp->bau_msg_head = bau_tablesp->va_queue_first;
bcp->va_queue_first = bau_tablesp->va_queue_first;
bcp->va_queue_last = bau_tablesp->va_queue_last;
struct bau_desc *adp;
struct bau_desc *ad2;
- adp = (struct bau_desc *)
- kmalloc_node(16384, GFP_KERNEL, node);
+ adp = (struct bau_desc *)kmalloc_node(16384, GFP_KERNEL, node);
BUG_ON(!adp);
- pa = __pa((unsigned long)adp);
+ pa = uv_gpa(adp); /* need the real nasid*/
n = pa >> uv_nshift;
m = pa & uv_mmask;
for (i = 0, ad2 = adp; i < UV_ACTIVATION_DESCRIPTOR_SIZE; i++, ad2++) {
memset(ad2, 0, sizeof(struct bau_desc));
ad2->header.sw_ack_flag = 1;
- ad2->header.base_dest_nodeid =
- uv_blade_to_pnode(uv_cpu_to_blade_id(0));
+ /*
+ * base_dest_nodeid is the first node in the partition, so
+ * the bit map will indicate partition-relative node numbers.
+ * note that base_dest_nodeid is actually a nasid.
+ */
+ ad2->header.base_dest_nodeid = uv_partition_base_pnode << 1;
ad2->header.command = UV_NET_ENDPOINT_INTD;
ad2->header.int_both = 1;
/*
uv_payload_queue_init(int node, int pnode, struct bau_control *bau_tablesp)
{
struct bau_payload_queue_entry *pqp;
+ unsigned long pa;
+ int pn;
char *cp;
pqp = (struct bau_payload_queue_entry *) kmalloc_node(
cp = (char *)pqp + 31;
pqp = (struct bau_payload_queue_entry *)(((unsigned long)cp >> 5) << 5);
bau_tablesp->va_queue_first = pqp;
+ /*
+ * need the pnode of where the memory was really allocated
+ */
+ pa = uv_gpa(pqp);
+ pn = pa >> uv_nshift;
uv_write_global_mmr64(pnode,
UVH_LB_BAU_INTD_PAYLOAD_QUEUE_FIRST,
- ((unsigned long)pnode <<
- UV_PAYLOADQ_PNODE_SHIFT) |
+ ((unsigned long)pn << UV_PAYLOADQ_PNODE_SHIFT) |
uv_physnodeaddr(pqp));
uv_write_global_mmr64(pnode, UVH_LB_BAU_INTD_PAYLOAD_QUEUE_TAIL,
uv_physnodeaddr(pqp));
/*
* Initialization of each UV blade's structures
*/
-static int __init uv_init_blade(int blade, int node, int cur_cpu)
+static int __init uv_init_blade(int blade)
{
+ int node;
int pnode;
unsigned long pa;
unsigned long apicid;
struct bau_payload_queue_entry *pqp;
struct bau_control *bau_tablesp;
+ node = blade_to_first_node(blade);
bau_tablesp = uv_table_bases_init(blade, node);
pnode = uv_blade_to_pnode(blade);
adp = uv_activation_descriptor_init(node, pnode);
pqp = uv_payload_queue_init(node, pnode, bau_tablesp);
- uv_table_bases_finish(blade, node, cur_cpu, bau_tablesp, adp);
+ uv_table_bases_finish(blade, bau_tablesp, adp);
/*
* the below initialization can't be in firmware because the
* messaging IRQ will be determined by the OS
*/
- apicid = per_cpu(x86_cpu_to_apicid, cur_cpu);
+ apicid = blade_to_first_apicid(blade);
pa = uv_read_global_mmr64(pnode, UVH_BAU_DATA_CONFIG);
if ((pa & 0xff) != UV_BAU_MESSAGE) {
uv_write_global_mmr64(pnode, UVH_BAU_DATA_CONFIG,
static int __init uv_bau_init(void)
{
int blade;
- int node;
int nblades;
- int last_blade;
int cur_cpu;
if (!is_uv_system())
uv_bau_retry_limit = 1;
uv_nshift = uv_hub_info->n_val;
uv_mmask = (1UL << uv_hub_info->n_val) - 1;
- nblades = 0;
- last_blade = -1;
- cur_cpu = 0;
- for_each_online_node(node) {
- blade = uv_node_to_blade_id(node);
- if (blade == last_blade)
- continue;
- last_blade = blade;
- nblades++;
- }
+ nblades = uv_num_possible_blades();
+
uv_bau_table_bases = (struct bau_control **)
kmalloc(nblades * sizeof(struct bau_control *), GFP_KERNEL);
BUG_ON(!uv_bau_table_bases);
- last_blade = -1;
- for_each_online_node(node) {
- blade = uv_node_to_blade_id(node);
- if (blade == last_blade)
- continue;
- last_blade = blade;
- uv_init_blade(blade, node, cur_cpu);
- cur_cpu += uv_blade_nr_possible_cpus(blade);
- }
+ uv_partition_base_pnode = 0x7fffffff;
+ for (blade = 0; blade < nblades; blade++)
+ if (uv_blade_nr_possible_cpus(blade) &&
+ (uv_blade_to_pnode(blade) < uv_partition_base_pnode))
+ uv_partition_base_pnode = uv_blade_to_pnode(blade);
+ for (blade = 0; blade < nblades; blade++)
+ if (uv_blade_nr_possible_cpus(blade))
+ uv_init_blade(blade);
+
alloc_intr_gate(UV_BAU_MESSAGE, uv_bau_message_intr1);
uv_enable_timeouts();
#include <linux/sysdev.h>
#include <asm/uv/bios.h>
+#include <asm/uv/uv.h>
struct kobject *sgi_uv_kobj;
{
unsigned long ret;
+ if (!is_uv_system())
+ return -ENODEV;
+
if (!sgi_uv_kobj)
sgi_uv_kobj = kobject_create_and_add("sgi_uv", firmware_kobj);
if (!sgi_uv_kobj) {
* controls the entire thing and the Guest asks it to make changes using the
* LOAD_GDT hypercall.
*
- * This is the opposite of the IDT code where we have a LOAD_IDT_ENTRY
- * hypercall and use that repeatedly to load a new IDT. I don't think it
- * really matters, but wouldn't it be nice if they were the same? Wouldn't
- * it be even better if you were the one to send the patch to fix it?
+ * This is the exactly like the IDT code.
*/
static void lguest_load_gdt(const struct desc_ptr *desc)
{
- BUG_ON((desc->size + 1) / 8 != GDT_ENTRIES);
- kvm_hypercall2(LHCALL_LOAD_GDT, __pa(desc->address), GDT_ENTRIES);
+ unsigned int i;
+ struct desc_struct *gdt = (void *)desc->address;
+
+ for (i = 0; i < (desc->size+1)/8; i++)
+ kvm_hypercall3(LHCALL_LOAD_GDT_ENTRY, i, gdt[i].a, gdt[i].b);
}
/* For a single GDT entry which changes, we do the lazy thing: alter our GDT,
const void *desc, int type)
{
native_write_gdt_entry(dt, entrynum, desc, type);
- kvm_hypercall2(LHCALL_LOAD_GDT, __pa(dt), GDT_ENTRIES);
+ /* Tell Host about this new entry. */
+ kvm_hypercall3(LHCALL_LOAD_GDT_ENTRY, entrynum,
+ dt[entrynum].a, dt[entrynum].b);
}
/* OK, I lied. There are three "thread local storage" GDT entries which change
return NULL;
area->phys_addr = phys_addr;
vaddr = (unsigned long) area->addr;
- if (ioremap_page_range(vaddr, vaddr + size, phys_addr, prot)) {
+
+ if (kernel_map_sync_memtype(phys_addr, size, prot_val)) {
free_memtype(phys_addr, phys_addr + size);
free_vm_area(area);
return NULL;
}
- if (ioremap_change_attr(vaddr, size, prot_val) < 0) {
+ if (ioremap_page_range(vaddr, vaddr + size, phys_addr, prot)) {
free_memtype(phys_addr, phys_addr + size);
- vunmap(area->addr);
+ free_vm_area(area);
return NULL;
}
* - UC_MINUS for non-WB-able memory with no other conflicting mappings
* - Inherit from confliting mappings otherwise
*/
- err = reserve_memtype(phys_addr, phys_addr + size, -1, &flags);
+ err = reserve_memtype(phys_addr, phys_addr + size,
+ _PAGE_CACHE_WB, &flags);
if (err < 0)
return NULL;
int set_memory_uc(unsigned long addr, int numpages)
{
+ int ret;
+
/*
* for now UC MINUS. see comments in ioremap_nocache()
*/
- if (reserve_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE,
- _PAGE_CACHE_UC_MINUS, NULL))
- return -EINVAL;
+ ret = reserve_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE,
+ _PAGE_CACHE_UC_MINUS, NULL);
+ if (ret)
+ goto out_err;
+
+ ret = _set_memory_uc(addr, numpages);
+ if (ret)
+ goto out_free;
- return _set_memory_uc(addr, numpages);
+ return 0;
+
+out_free:
+ free_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE);
+out_err:
+ return ret;
}
EXPORT_SYMBOL(set_memory_uc);
int set_memory_array_uc(unsigned long *addr, int addrinarray)
{
- unsigned long start;
- unsigned long end;
- int i;
+ int i, j;
+ int ret;
+
/*
* for now UC MINUS. see comments in ioremap_nocache()
*/
for (i = 0; i < addrinarray; i++) {
- start = __pa(addr[i]);
- for (end = start + PAGE_SIZE; i < addrinarray - 1; end += PAGE_SIZE) {
- if (end != __pa(addr[i + 1]))
- break;
- i++;
- }
- if (reserve_memtype(start, end, _PAGE_CACHE_UC_MINUS, NULL))
- goto out;
+ ret = reserve_memtype(__pa(addr[i]), __pa(addr[i]) + PAGE_SIZE,
+ _PAGE_CACHE_UC_MINUS, NULL);
+ if (ret)
+ goto out_free;
}
- return change_page_attr_set(addr, addrinarray,
+ ret = change_page_attr_set(addr, addrinarray,
__pgprot(_PAGE_CACHE_UC_MINUS), 1);
-out:
- for (i = 0; i < addrinarray; i++) {
- unsigned long tmp = __pa(addr[i]);
-
- if (tmp == start)
- break;
- for (end = tmp + PAGE_SIZE; i < addrinarray - 1; end += PAGE_SIZE) {
- if (end != __pa(addr[i + 1]))
- break;
- i++;
- }
- free_memtype(tmp, end);
- }
- return -EINVAL;
+ if (ret)
+ goto out_free;
+
+ return 0;
+
+out_free:
+ for (j = 0; j < i; j++)
+ free_memtype(__pa(addr[j]), __pa(addr[j]) + PAGE_SIZE);
+
+ return ret;
}
EXPORT_SYMBOL(set_memory_array_uc);
int _set_memory_wc(unsigned long addr, int numpages)
{
- return change_page_attr_set(&addr, numpages,
+ int ret;
+ ret = change_page_attr_set(&addr, numpages,
+ __pgprot(_PAGE_CACHE_UC_MINUS), 0);
+
+ if (!ret) {
+ ret = change_page_attr_set(&addr, numpages,
__pgprot(_PAGE_CACHE_WC), 0);
+ }
+ return ret;
}
int set_memory_wc(unsigned long addr, int numpages)
{
+ int ret;
+
if (!pat_enabled)
return set_memory_uc(addr, numpages);
- if (reserve_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE,
- _PAGE_CACHE_WC, NULL))
- return -EINVAL;
+ ret = reserve_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE,
+ _PAGE_CACHE_WC, NULL);
+ if (ret)
+ goto out_err;
+
+ ret = _set_memory_wc(addr, numpages);
+ if (ret)
+ goto out_free;
+
+ return 0;
- return _set_memory_wc(addr, numpages);
+out_free:
+ free_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE);
+out_err:
+ return ret;
}
EXPORT_SYMBOL(set_memory_wc);
int set_memory_wb(unsigned long addr, int numpages)
{
- free_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE);
+ int ret;
+
+ ret = _set_memory_wb(addr, numpages);
+ if (ret)
+ return ret;
- return _set_memory_wb(addr, numpages);
+ free_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE);
+ return 0;
}
EXPORT_SYMBOL(set_memory_wb);
int set_memory_array_wb(unsigned long *addr, int addrinarray)
{
int i;
+ int ret;
- for (i = 0; i < addrinarray; i++) {
- unsigned long start = __pa(addr[i]);
- unsigned long end;
-
- for (end = start + PAGE_SIZE; i < addrinarray - 1; end += PAGE_SIZE) {
- if (end != __pa(addr[i + 1]))
- break;
- i++;
- }
- free_memtype(start, end);
- }
- return change_page_attr_clear(addr, addrinarray,
+ ret = change_page_attr_clear(addr, addrinarray,
__pgprot(_PAGE_CACHE_MASK), 1);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < addrinarray; i++)
+ free_memtype(__pa(addr[i]), __pa(addr[i]) + PAGE_SIZE);
+
+ return 0;
}
EXPORT_SYMBOL(set_memory_array_wb);
retval = cpa_clear_pages_array(pages, addrinarray,
__pgprot(_PAGE_CACHE_MASK));
+ if (retval)
+ return retval;
for (i = 0; i < addrinarray; i++) {
start = (unsigned long)page_address(pages[i]);
free_memtype(start, end);
}
- return retval;
+ return 0;
}
EXPORT_SYMBOL(set_pages_array_wb);
u8 mtrr_type;
mtrr_type = mtrr_type_lookup(start, end);
- if (mtrr_type == MTRR_TYPE_UNCACHABLE)
- return _PAGE_CACHE_UC;
- if (mtrr_type == MTRR_TYPE_WRCOMB)
- return _PAGE_CACHE_WC;
+ if (mtrr_type != MTRR_TYPE_WRBACK)
+ return _PAGE_CACHE_UC_MINUS;
+
+ return _PAGE_CACHE_WB;
}
return req_type;
return 0;
}
- if (req_type == -1) {
- /*
- * Call mtrr_lookup to get the type hint. This is an
- * optimization for /dev/mem mmap'ers into WB memory (BIOS
- * tools and ACPI tools). Use WB request for WB memory and use
- * UC_MINUS otherwise.
- */
- u8 mtrr_type = mtrr_type_lookup(start, end);
-
- if (mtrr_type == MTRR_TYPE_WRBACK)
- actual_type = _PAGE_CACHE_WB;
- else
- actual_type = _PAGE_CACHE_UC_MINUS;
- } else {
- actual_type = pat_x_mtrr_type(start, end,
- req_type & _PAGE_CACHE_MASK);
- }
+ /*
+ * Call mtrr_lookup to get the type hint. This is an
+ * optimization for /dev/mem mmap'ers into WB memory (BIOS
+ * tools and ACPI tools). Use WB request for WB memory and use
+ * UC_MINUS otherwise.
+ */
+ actual_type = pat_x_mtrr_type(start, end, req_type & _PAGE_CACHE_MASK);
if (new_type)
*new_type = actual_type;
int phys_mem_access_prot_allowed(struct file *file, unsigned long pfn,
unsigned long size, pgprot_t *vma_prot)
{
- u64 offset = ((u64) pfn) << PAGE_SHIFT;
- unsigned long flags = -1;
- int retval;
+ unsigned long flags = _PAGE_CACHE_WB;
if (!range_is_allowed(pfn, size))
return 0;
}
#endif
- /*
- * With O_SYNC, we can only take UC_MINUS mapping. Fail if we cannot.
- *
- * Without O_SYNC, we want to get
- * - WB for WB-able memory and no other conflicting mappings
- * - UC_MINUS for non-WB-able memory with no other conflicting mappings
- * - Inherit from confliting mappings otherwise
- */
- if (flags != -1) {
- retval = reserve_memtype(offset, offset + size, flags, NULL);
- } else {
- retval = reserve_memtype(offset, offset + size, -1, &flags);
- }
-
- if (retval < 0)
- return 0;
-
- if (((pfn < max_low_pfn_mapped) ||
- (pfn >= (1UL<<(32 - PAGE_SHIFT)) && pfn < max_pfn_mapped)) &&
- ioremap_change_attr((unsigned long)__va(offset), size, flags) < 0) {
- free_memtype(offset, offset + size);
- printk(KERN_INFO
- "%s:%d /dev/mem ioremap_change_attr failed %s for %Lx-%Lx\n",
- current->comm, current->pid,
- cattr_name(flags),
- offset, (unsigned long long)(offset + size));
- return 0;
- }
-
*vma_prot = __pgprot((pgprot_val(*vma_prot) & ~_PAGE_CACHE_MASK) |
flags);
return 1;
}
-void map_devmem(unsigned long pfn, unsigned long size, pgprot_t vma_prot)
-{
- unsigned long want_flags = (pgprot_val(vma_prot) & _PAGE_CACHE_MASK);
- u64 addr = (u64)pfn << PAGE_SHIFT;
- unsigned long flags;
-
- reserve_memtype(addr, addr + size, want_flags, &flags);
- if (flags != want_flags) {
- printk(KERN_INFO
- "%s:%d /dev/mem expected mapping type %s for %Lx-%Lx, got %s\n",
- current->comm, current->pid,
- cattr_name(want_flags),
- addr, (unsigned long long)(addr + size),
- cattr_name(flags));
- }
-}
-
-void unmap_devmem(unsigned long pfn, unsigned long size, pgprot_t vma_prot)
-{
- u64 addr = (u64)pfn << PAGE_SHIFT;
-
- free_memtype(addr, addr + size);
-}
-
/*
* Change the memory type for the physial address range in kernel identity
* mapping space if that range is a part of identity map.
{
int is_ram = 0;
int ret;
- unsigned long flags;
unsigned long want_flags = (pgprot_val(*vma_prot) & _PAGE_CACHE_MASK);
+ unsigned long flags = want_flags;
is_ram = pat_pagerange_is_ram(paddr, paddr + size);
*
* If the vma has a linear pfn mapping for the entire range, we get the prot
* from pte and reserve the entire vma range with single reserve_pfn_range call.
- * Otherwise, we reserve the entire vma range, my ging through the PTEs page
- * by page to get physical address and protection.
*/
int track_pfn_vma_copy(struct vm_area_struct *vma)
{
- int retval = 0;
- unsigned long i, j;
resource_size_t paddr;
unsigned long prot;
- unsigned long vma_start = vma->vm_start;
- unsigned long vma_end = vma->vm_end;
- unsigned long vma_size = vma_end - vma_start;
+ unsigned long vma_size = vma->vm_end - vma->vm_start;
pgprot_t pgprot;
if (!pat_enabled)
return 0;
+ /*
+ * For now, only handle remap_pfn_range() vmas where
+ * is_linear_pfn_mapping() == TRUE. Handling of
+ * vm_insert_pfn() is TBD.
+ */
if (is_linear_pfn_mapping(vma)) {
/*
* reserve the whole chunk covered by vma. We need the
* starting address and protection from pte.
*/
- if (follow_phys(vma, vma_start, 0, &prot, &paddr)) {
+ if (follow_phys(vma, vma->vm_start, 0, &prot, &paddr)) {
WARN_ON_ONCE(1);
return -EINVAL;
}
return reserve_pfn_range(paddr, vma_size, &pgprot, 1);
}
- /* reserve entire vma page by page, using pfn and prot from pte */
- for (i = 0; i < vma_size; i += PAGE_SIZE) {
- if (follow_phys(vma, vma_start + i, 0, &prot, &paddr))
- continue;
-
- pgprot = __pgprot(prot);
- retval = reserve_pfn_range(paddr, PAGE_SIZE, &pgprot, 1);
- if (retval)
- goto cleanup_ret;
- }
return 0;
-
-cleanup_ret:
- /* Reserve error: Cleanup partial reservation and return error */
- for (j = 0; j < i; j += PAGE_SIZE) {
- if (follow_phys(vma, vma_start + j, 0, &prot, &paddr))
- continue;
-
- free_pfn_range(paddr, PAGE_SIZE);
- }
-
- return retval;
}
/*
* prot is passed in as a parameter for the new mapping. If the vma has a
* linear pfn mapping for the entire range reserve the entire vma range with
* single reserve_pfn_range call.
- * Otherwise, we look t the pfn and size and reserve only the specified range
- * page by page.
- *
- * Note that this function can be called with caller trying to map only a
- * subrange/page inside the vma.
*/
int track_pfn_vma_new(struct vm_area_struct *vma, pgprot_t *prot,
unsigned long pfn, unsigned long size)
{
- int retval = 0;
- unsigned long i, j;
- resource_size_t base_paddr;
resource_size_t paddr;
- unsigned long vma_start = vma->vm_start;
- unsigned long vma_end = vma->vm_end;
- unsigned long vma_size = vma_end - vma_start;
+ unsigned long vma_size = vma->vm_end - vma->vm_start;
if (!pat_enabled)
return 0;
+ /*
+ * For now, only handle remap_pfn_range() vmas where
+ * is_linear_pfn_mapping() == TRUE. Handling of
+ * vm_insert_pfn() is TBD.
+ */
if (is_linear_pfn_mapping(vma)) {
/* reserve the whole chunk starting from vm_pgoff */
paddr = (resource_size_t)vma->vm_pgoff << PAGE_SHIFT;
return reserve_pfn_range(paddr, vma_size, prot, 0);
}
- /* reserve page by page using pfn and size */
- base_paddr = (resource_size_t)pfn << PAGE_SHIFT;
- for (i = 0; i < size; i += PAGE_SIZE) {
- paddr = base_paddr + i;
- retval = reserve_pfn_range(paddr, PAGE_SIZE, prot, 0);
- if (retval)
- goto cleanup_ret;
- }
return 0;
-
-cleanup_ret:
- /* Reserve error: Cleanup partial reservation and return error */
- for (j = 0; j < i; j += PAGE_SIZE) {
- paddr = base_paddr + j;
- free_pfn_range(paddr, PAGE_SIZE);
- }
-
- return retval;
}
/*
void untrack_pfn_vma(struct vm_area_struct *vma, unsigned long pfn,
unsigned long size)
{
- unsigned long i;
resource_size_t paddr;
- unsigned long prot;
- unsigned long vma_start = vma->vm_start;
- unsigned long vma_end = vma->vm_end;
- unsigned long vma_size = vma_end - vma_start;
+ unsigned long vma_size = vma->vm_end - vma->vm_start;
if (!pat_enabled)
return;
+ /*
+ * For now, only handle remap_pfn_range() vmas where
+ * is_linear_pfn_mapping() == TRUE. Handling of
+ * vm_insert_pfn() is TBD.
+ */
if (is_linear_pfn_mapping(vma)) {
/* free the whole chunk starting from vm_pgoff */
paddr = (resource_size_t)vma->vm_pgoff << PAGE_SHIFT;
free_pfn_range(paddr, vma_size);
return;
}
-
- if (size != 0 && size != vma_size) {
- /* free page by page, using pfn and size */
- paddr = (resource_size_t)pfn << PAGE_SHIFT;
- for (i = 0; i < size; i += PAGE_SIZE) {
- paddr = paddr + i;
- free_pfn_range(paddr, PAGE_SIZE);
- }
- } else {
- /* free entire vma, page by page, using the pfn from pte */
- for (i = 0; i < vma_size; i += PAGE_SIZE) {
- if (follow_phys(vma, vma_start + i, 0, &prot, &paddr))
- continue;
-
- free_pfn_range(paddr, PAGE_SIZE);
- }
- }
}
pgprot_t pgprot_writecombine(pgprot_t prot)
#include <linux/rbtree.h>
#include <linux/interrupt.h>
-#define REQ_SYNC 1
-#define REQ_ASYNC 0
-
/*
* See Documentation/block/as-iosched.txt
*/
struct list_head fifo_list[2];
struct request *next_rq[2]; /* next in sort order */
- sector_t last_sector[2]; /* last REQ_SYNC & REQ_ASYNC sectors */
+ sector_t last_sector[2]; /* last SYNC & ASYNC sectors */
unsigned long exit_prob; /* probability a task will exit while
being waited on */
unsigned long last_check_fifo[2];
int changed_batch; /* 1: waiting for old batch to end */
int new_batch; /* 1: waiting on first read complete */
- int batch_data_dir; /* current batch REQ_SYNC / REQ_ASYNC */
+ int batch_data_dir; /* current batch SYNC / ASYNC */
int write_batch_count; /* max # of reqs in a write batch */
int current_write_count; /* how many requests left this batch */
int write_batch_idled; /* has the write batch gone idle? */
if (aic == NULL)
return;
- if (data_dir == REQ_SYNC) {
+ if (data_dir == BLK_RW_SYNC) {
unsigned long in_flight = atomic_read(&aic->nr_queued)
+ atomic_read(&aic->nr_dispatched);
spin_lock(&aic->lock);
*/
static void update_write_batch(struct as_data *ad)
{
- unsigned long batch = ad->batch_expire[REQ_ASYNC];
+ unsigned long batch = ad->batch_expire[BLK_RW_ASYNC];
long write_time;
write_time = (jiffies - ad->current_batch_expires) + batch;
kblockd_schedule_work(q, &ad->antic_work);
ad->changed_batch = 0;
- if (ad->batch_data_dir == REQ_SYNC)
+ if (ad->batch_data_dir == BLK_RW_SYNC)
ad->new_batch = 1;
}
WARN_ON(ad->nr_dispatched == 0);
if (ad->new_batch && ad->batch_data_dir == rq_is_sync(rq)) {
update_write_batch(ad);
ad->current_batch_expires = jiffies +
- ad->batch_expire[REQ_SYNC];
+ ad->batch_expire[BLK_RW_SYNC];
ad->new_batch = 0;
}
if (ad->changed_batch || ad->new_batch)
return 0;
- if (ad->batch_data_dir == REQ_SYNC)
+ if (ad->batch_data_dir == BLK_RW_SYNC)
/* TODO! add a check so a complete fifo gets written? */
return time_after(jiffies, ad->current_batch_expires);
*/
ad->last_sector[data_dir] = rq->sector + rq->nr_sectors;
- if (data_dir == REQ_SYNC) {
+ if (data_dir == BLK_RW_SYNC) {
struct io_context *ioc = RQ_IOC(rq);
/* In case we have to anticipate after this */
copy_io_context(&ad->io_context, &ioc);
static int as_dispatch_request(struct request_queue *q, int force)
{
struct as_data *ad = q->elevator->elevator_data;
- const int reads = !list_empty(&ad->fifo_list[REQ_SYNC]);
- const int writes = !list_empty(&ad->fifo_list[REQ_ASYNC]);
+ const int reads = !list_empty(&ad->fifo_list[BLK_RW_SYNC]);
+ const int writes = !list_empty(&ad->fifo_list[BLK_RW_ASYNC]);
struct request *rq;
if (unlikely(force)) {
/*
* Forced dispatch, accounting is useless. Reset
* accounting states and dump fifo_lists. Note that
- * batch_data_dir is reset to REQ_SYNC to avoid
+ * batch_data_dir is reset to BLK_RW_SYNC to avoid
* screwing write batch accounting as write batch
* accounting occurs on W->R transition.
*/
int dispatched = 0;
- ad->batch_data_dir = REQ_SYNC;
+ ad->batch_data_dir = BLK_RW_SYNC;
ad->changed_batch = 0;
ad->new_batch = 0;
- while (ad->next_rq[REQ_SYNC]) {
- as_move_to_dispatch(ad, ad->next_rq[REQ_SYNC]);
+ while (ad->next_rq[BLK_RW_SYNC]) {
+ as_move_to_dispatch(ad, ad->next_rq[BLK_RW_SYNC]);
dispatched++;
}
- ad->last_check_fifo[REQ_SYNC] = jiffies;
+ ad->last_check_fifo[BLK_RW_SYNC] = jiffies;
- while (ad->next_rq[REQ_ASYNC]) {
- as_move_to_dispatch(ad, ad->next_rq[REQ_ASYNC]);
+ while (ad->next_rq[BLK_RW_ASYNC]) {
+ as_move_to_dispatch(ad, ad->next_rq[BLK_RW_ASYNC]);
dispatched++;
}
- ad->last_check_fifo[REQ_ASYNC] = jiffies;
+ ad->last_check_fifo[BLK_RW_ASYNC] = jiffies;
return dispatched;
}
/* Signal that the write batch was uncontended, so we can't time it */
- if (ad->batch_data_dir == REQ_ASYNC && !reads) {
+ if (ad->batch_data_dir == BLK_RW_ASYNC && !reads) {
if (ad->current_write_count == 0 || !writes)
ad->write_batch_idled = 1;
}
*/
rq = ad->next_rq[ad->batch_data_dir];
- if (ad->batch_data_dir == REQ_SYNC && ad->antic_expire) {
- if (as_fifo_expired(ad, REQ_SYNC))
+ if (ad->batch_data_dir == BLK_RW_SYNC && ad->antic_expire) {
+ if (as_fifo_expired(ad, BLK_RW_SYNC))
goto fifo_expired;
if (as_can_anticipate(ad, rq)) {
/* we have a "next request" */
if (reads && !writes)
ad->current_batch_expires =
- jiffies + ad->batch_expire[REQ_SYNC];
+ jiffies + ad->batch_expire[BLK_RW_SYNC];
goto dispatch_request;
}
}
*/
if (reads) {
- BUG_ON(RB_EMPTY_ROOT(&ad->sort_list[REQ_SYNC]));
+ BUG_ON(RB_EMPTY_ROOT(&ad->sort_list[BLK_RW_SYNC]));
- if (writes && ad->batch_data_dir == REQ_SYNC)
+ if (writes && ad->batch_data_dir == BLK_RW_SYNC)
/*
* Last batch was a read, switch to writes
*/
goto dispatch_writes;
- if (ad->batch_data_dir == REQ_ASYNC) {
+ if (ad->batch_data_dir == BLK_RW_ASYNC) {
WARN_ON(ad->new_batch);
ad->changed_batch = 1;
}
- ad->batch_data_dir = REQ_SYNC;
- rq = rq_entry_fifo(ad->fifo_list[REQ_SYNC].next);
+ ad->batch_data_dir = BLK_RW_SYNC;
+ rq = rq_entry_fifo(ad->fifo_list[BLK_RW_SYNC].next);
ad->last_check_fifo[ad->batch_data_dir] = jiffies;
goto dispatch_request;
}
if (writes) {
dispatch_writes:
- BUG_ON(RB_EMPTY_ROOT(&ad->sort_list[REQ_ASYNC]));
+ BUG_ON(RB_EMPTY_ROOT(&ad->sort_list[BLK_RW_ASYNC]));
- if (ad->batch_data_dir == REQ_SYNC) {
+ if (ad->batch_data_dir == BLK_RW_SYNC) {
ad->changed_batch = 1;
/*
*/
ad->new_batch = 0;
}
- ad->batch_data_dir = REQ_ASYNC;
+ ad->batch_data_dir = BLK_RW_ASYNC;
ad->current_write_count = ad->write_batch_count;
ad->write_batch_idled = 0;
- rq = rq_entry_fifo(ad->fifo_list[REQ_ASYNC].next);
- ad->last_check_fifo[REQ_ASYNC] = jiffies;
+ rq = rq_entry_fifo(ad->fifo_list[BLK_RW_ASYNC].next);
+ ad->last_check_fifo[BLK_RW_ASYNC] = jiffies;
goto dispatch_request;
}
if (ad->nr_dispatched)
return 0;
- if (ad->batch_data_dir == REQ_ASYNC)
+ if (ad->batch_data_dir == BLK_RW_ASYNC)
ad->current_batch_expires = jiffies +
- ad->batch_expire[REQ_ASYNC];
+ ad->batch_expire[BLK_RW_ASYNC];
else
ad->new_batch = 1;
{
struct as_data *ad = q->elevator->elevator_data;
- return list_empty(&ad->fifo_list[REQ_ASYNC])
- && list_empty(&ad->fifo_list[REQ_SYNC]);
+ return list_empty(&ad->fifo_list[BLK_RW_ASYNC])
+ && list_empty(&ad->fifo_list[BLK_RW_SYNC]);
}
static int
del_timer_sync(&ad->antic_timer);
cancel_work_sync(&ad->antic_work);
- BUG_ON(!list_empty(&ad->fifo_list[REQ_SYNC]));
- BUG_ON(!list_empty(&ad->fifo_list[REQ_ASYNC]));
+ BUG_ON(!list_empty(&ad->fifo_list[BLK_RW_SYNC]));
+ BUG_ON(!list_empty(&ad->fifo_list[BLK_RW_ASYNC]));
put_io_context(ad->io_context);
kfree(ad);
init_timer(&ad->antic_timer);
INIT_WORK(&ad->antic_work, as_work_handler);
- INIT_LIST_HEAD(&ad->fifo_list[REQ_SYNC]);
- INIT_LIST_HEAD(&ad->fifo_list[REQ_ASYNC]);
- ad->sort_list[REQ_SYNC] = RB_ROOT;
- ad->sort_list[REQ_ASYNC] = RB_ROOT;
- ad->fifo_expire[REQ_SYNC] = default_read_expire;
- ad->fifo_expire[REQ_ASYNC] = default_write_expire;
+ INIT_LIST_HEAD(&ad->fifo_list[BLK_RW_SYNC]);
+ INIT_LIST_HEAD(&ad->fifo_list[BLK_RW_ASYNC]);
+ ad->sort_list[BLK_RW_SYNC] = RB_ROOT;
+ ad->sort_list[BLK_RW_ASYNC] = RB_ROOT;
+ ad->fifo_expire[BLK_RW_SYNC] = default_read_expire;
+ ad->fifo_expire[BLK_RW_ASYNC] = default_write_expire;
ad->antic_expire = default_antic_expire;
- ad->batch_expire[REQ_SYNC] = default_read_batch_expire;
- ad->batch_expire[REQ_ASYNC] = default_write_batch_expire;
+ ad->batch_expire[BLK_RW_SYNC] = default_read_batch_expire;
+ ad->batch_expire[BLK_RW_ASYNC] = default_write_batch_expire;
- ad->current_batch_expires = jiffies + ad->batch_expire[REQ_SYNC];
- ad->write_batch_count = ad->batch_expire[REQ_ASYNC] / 10;
+ ad->current_batch_expires = jiffies + ad->batch_expire[BLK_RW_SYNC];
+ ad->write_batch_count = ad->batch_expire[BLK_RW_ASYNC] / 10;
if (ad->write_batch_count < 2)
ad->write_batch_count = 2;
struct as_data *ad = e->elevator_data; \
return as_var_show(jiffies_to_msecs((__VAR)), (page)); \
}
-SHOW_FUNCTION(as_read_expire_show, ad->fifo_expire[REQ_SYNC]);
-SHOW_FUNCTION(as_write_expire_show, ad->fifo_expire[REQ_ASYNC]);
+SHOW_FUNCTION(as_read_expire_show, ad->fifo_expire[BLK_RW_SYNC]);
+SHOW_FUNCTION(as_write_expire_show, ad->fifo_expire[BLK_RW_ASYNC]);
SHOW_FUNCTION(as_antic_expire_show, ad->antic_expire);
-SHOW_FUNCTION(as_read_batch_expire_show, ad->batch_expire[REQ_SYNC]);
-SHOW_FUNCTION(as_write_batch_expire_show, ad->batch_expire[REQ_ASYNC]);
+SHOW_FUNCTION(as_read_batch_expire_show, ad->batch_expire[BLK_RW_SYNC]);
+SHOW_FUNCTION(as_write_batch_expire_show, ad->batch_expire[BLK_RW_ASYNC]);
#undef SHOW_FUNCTION
#define STORE_FUNCTION(__FUNC, __PTR, MIN, MAX) \
*(__PTR) = msecs_to_jiffies(*(__PTR)); \
return ret; \
}
-STORE_FUNCTION(as_read_expire_store, &ad->fifo_expire[REQ_SYNC], 0, INT_MAX);
-STORE_FUNCTION(as_write_expire_store, &ad->fifo_expire[REQ_ASYNC], 0, INT_MAX);
+STORE_FUNCTION(as_read_expire_store, &ad->fifo_expire[BLK_RW_SYNC], 0, INT_MAX);
+STORE_FUNCTION(as_write_expire_store,
+ &ad->fifo_expire[BLK_RW_ASYNC], 0, INT_MAX);
STORE_FUNCTION(as_antic_expire_store, &ad->antic_expire, 0, INT_MAX);
STORE_FUNCTION(as_read_batch_expire_store,
- &ad->batch_expire[REQ_SYNC], 0, INT_MAX);
+ &ad->batch_expire[BLK_RW_SYNC], 0, INT_MAX);
STORE_FUNCTION(as_write_batch_expire_store,
- &ad->batch_expire[REQ_ASYNC], 0, INT_MAX);
+ &ad->batch_expire[BLK_RW_ASYNC], 0, INT_MAX);
#undef STORE_FUNCTION
#define AS_ATTR(name) \
return -ENXIO;
bio = bio_alloc(GFP_KERNEL, 0);
- if (!bio)
- return -ENOMEM;
-
bio->bi_end_io = bio_end_empty_barrier;
bio->bi_private = &wait;
bio->bi_bdev = bdev;
ssize_t ret = queue_var_store(&stats, page, count);
spin_lock_irq(q->queue_lock);
- elv_quisce_start(q);
+ elv_quiesce_start(q);
if (stats)
queue_flag_set(QUEUE_FLAG_IO_STAT, q);
else
queue_flag_clear(QUEUE_FLAG_IO_STAT, q);
- elv_quisce_end(q);
+ elv_quiesce_end(q);
spin_unlock_irq(q->queue_lock);
return ret;
int blk_dev_init(void);
-void elv_quisce_start(struct request_queue *q);
-void elv_quisce_end(struct request_queue *q);
+void elv_quiesce_start(struct request_queue *q);
+void elv_quiesce_end(struct request_queue *q);
/*
#define cfq_class_idle(cfqq) ((cfqq)->ioprio_class == IOPRIO_CLASS_IDLE)
#define cfq_class_rt(cfqq) ((cfqq)->ioprio_class == IOPRIO_CLASS_RT)
-#define ASYNC (0)
-#define SYNC (1)
-
#define sample_valid(samples) ((samples) > 80)
/*
* rr list of queues with requests and the count of them
*/
struct cfq_rb_root service_tree;
+
+ /*
+ * Each priority tree is sorted by next_request position. These
+ * trees are used when determining if two or more queues are
+ * interleaving requests (see cfq_close_cooperator).
+ */
+ struct rb_root prio_trees[CFQ_PRIO_LISTS];
+
unsigned int busy_queues;
/*
* Used to track any pending rt requests so we can pre-empt current
struct rb_node rb_node;
/* service_tree key */
unsigned long rb_key;
+ /* prio tree member */
+ struct rb_node p_node;
/* sorted list of pending requests */
struct rb_root sort_list;
/* if fifo isn't expired, next request to serve */
CFQ_CFQQ_FLAG_prio_changed, /* task priority has changed */
CFQ_CFQQ_FLAG_slice_new, /* no requests dispatched in slice */
CFQ_CFQQ_FLAG_sync, /* synchronous queue */
+ CFQ_CFQQ_FLAG_coop, /* has done a coop jump of the queue */
};
#define CFQ_CFQQ_FNS(name) \
CFQ_CFQQ_FNS(prio_changed);
CFQ_CFQQ_FNS(slice_new);
CFQ_CFQQ_FNS(sync);
+CFQ_CFQQ_FNS(coop);
#undef CFQ_CFQQ_FNS
#define cfq_log_cfqq(cfqd, cfqq, fmt, args...) \
return NULL;
}
+static void rb_erase_init(struct rb_node *n, struct rb_root *root)
+{
+ rb_erase(n, root);
+ RB_CLEAR_NODE(n);
+}
+
static void cfq_rb_erase(struct rb_node *n, struct cfq_rb_root *root)
{
if (root->left == n)
root->left = NULL;
-
- rb_erase(n, &root->rb);
- RB_CLEAR_NODE(n);
+ rb_erase_init(n, &root->rb);
}
/*
* requests waiting to be processed. It is sorted in the order that
* we will service the queues.
*/
-static void cfq_service_tree_add(struct cfq_data *cfqd,
- struct cfq_queue *cfqq, int add_front)
+static void cfq_service_tree_add(struct cfq_data *cfqd, struct cfq_queue *cfqq,
+ int add_front)
{
struct rb_node **p, *parent;
struct cfq_queue *__cfqq;
rb_insert_color(&cfqq->rb_node, &cfqd->service_tree.rb);
}
+static struct cfq_queue *
+cfq_prio_tree_lookup(struct cfq_data *cfqd, int ioprio, sector_t sector,
+ struct rb_node **ret_parent, struct rb_node ***rb_link)
+{
+ struct rb_root *root = &cfqd->prio_trees[ioprio];
+ struct rb_node **p, *parent;
+ struct cfq_queue *cfqq = NULL;
+
+ parent = NULL;
+ p = &root->rb_node;
+ while (*p) {
+ struct rb_node **n;
+
+ parent = *p;
+ cfqq = rb_entry(parent, struct cfq_queue, p_node);
+
+ /*
+ * Sort strictly based on sector. Smallest to the left,
+ * largest to the right.
+ */
+ if (sector > cfqq->next_rq->sector)
+ n = &(*p)->rb_right;
+ else if (sector < cfqq->next_rq->sector)
+ n = &(*p)->rb_left;
+ else
+ break;
+ p = n;
+ }
+
+ *ret_parent = parent;
+ if (rb_link)
+ *rb_link = p;
+ return NULL;
+}
+
+static void cfq_prio_tree_add(struct cfq_data *cfqd, struct cfq_queue *cfqq)
+{
+ struct rb_root *root = &cfqd->prio_trees[cfqq->ioprio];
+ struct rb_node **p, *parent;
+ struct cfq_queue *__cfqq;
+
+ if (!RB_EMPTY_NODE(&cfqq->p_node))
+ rb_erase_init(&cfqq->p_node, root);
+
+ if (cfq_class_idle(cfqq))
+ return;
+ if (!cfqq->next_rq)
+ return;
+
+ __cfqq = cfq_prio_tree_lookup(cfqd, cfqq->ioprio, cfqq->next_rq->sector,
+ &parent, &p);
+ BUG_ON(__cfqq);
+
+ rb_link_node(&cfqq->p_node, parent, p);
+ rb_insert_color(&cfqq->p_node, root);
+}
+
/*
* Update cfqq's position in the service tree.
*/
/*
* Resorting requires the cfqq to be on the RR list already.
*/
- if (cfq_cfqq_on_rr(cfqq))
+ if (cfq_cfqq_on_rr(cfqq)) {
cfq_service_tree_add(cfqd, cfqq, 0);
+ cfq_prio_tree_add(cfqd, cfqq);
+ }
}
/*
if (!RB_EMPTY_NODE(&cfqq->rb_node))
cfq_rb_erase(&cfqq->rb_node, &cfqd->service_tree);
+ if (!RB_EMPTY_NODE(&cfqq->p_node))
+ rb_erase_init(&cfqq->p_node, &cfqd->prio_trees[cfqq->ioprio]);
BUG_ON(!cfqd->busy_queues);
cfqd->busy_queues--;
{
struct cfq_queue *cfqq = RQ_CFQQ(rq);
struct cfq_data *cfqd = cfqq->cfqd;
- struct request *__alias;
+ struct request *__alias, *prev;
cfqq->queued[rq_is_sync(rq)]++;
/*
* check if this request is a better next-serve candidate
*/
+ prev = cfqq->next_rq;
cfqq->next_rq = cfq_choose_req(cfqd, cfqq->next_rq, rq);
+
+ /*
+ * adjust priority tree position, if ->next_rq changes
+ */
+ if (prev != cfqq->next_rq)
+ cfq_prio_tree_add(cfqd, cfqq);
+
BUG_ON(!cfqq->next_rq);
}
/*
* Get and set a new active queue for service.
*/
-static struct cfq_queue *cfq_set_active_queue(struct cfq_data *cfqd)
+static struct cfq_queue *cfq_set_active_queue(struct cfq_data *cfqd,
+ struct cfq_queue *cfqq)
{
- struct cfq_queue *cfqq;
+ if (!cfqq) {
+ cfqq = cfq_get_next_queue(cfqd);
+ if (cfqq)
+ cfq_clear_cfqq_coop(cfqq);
+ }
- cfqq = cfq_get_next_queue(cfqd);
__cfq_set_active_queue(cfqd, cfqq);
return cfqq;
}
return cfq_dist_from_last(cfqd, rq) <= cic->seek_mean;
}
-static int cfq_close_cooperator(struct cfq_data *cfq_data,
- struct cfq_queue *cfqq)
+static struct cfq_queue *cfqq_close(struct cfq_data *cfqd,
+ struct cfq_queue *cur_cfqq)
+{
+ struct rb_root *root = &cfqd->prio_trees[cur_cfqq->ioprio];
+ struct rb_node *parent, *node;
+ struct cfq_queue *__cfqq;
+ sector_t sector = cfqd->last_position;
+
+ if (RB_EMPTY_ROOT(root))
+ return NULL;
+
+ /*
+ * First, if we find a request starting at the end of the last
+ * request, choose it.
+ */
+ __cfqq = cfq_prio_tree_lookup(cfqd, cur_cfqq->ioprio,
+ sector, &parent, NULL);
+ if (__cfqq)
+ return __cfqq;
+
+ /*
+ * If the exact sector wasn't found, the parent of the NULL leaf
+ * will contain the closest sector.
+ */
+ __cfqq = rb_entry(parent, struct cfq_queue, p_node);
+ if (cfq_rq_close(cfqd, __cfqq->next_rq))
+ return __cfqq;
+
+ if (__cfqq->next_rq->sector < sector)
+ node = rb_next(&__cfqq->p_node);
+ else
+ node = rb_prev(&__cfqq->p_node);
+ if (!node)
+ return NULL;
+
+ __cfqq = rb_entry(node, struct cfq_queue, p_node);
+ if (cfq_rq_close(cfqd, __cfqq->next_rq))
+ return __cfqq;
+
+ return NULL;
+}
+
+/*
+ * cfqd - obvious
+ * cur_cfqq - passed in so that we don't decide that the current queue is
+ * closely cooperating with itself.
+ *
+ * So, basically we're assuming that that cur_cfqq has dispatched at least
+ * one request, and that cfqd->last_position reflects a position on the disk
+ * associated with the I/O issued by cur_cfqq. I'm not sure this is a valid
+ * assumption.
+ */
+static struct cfq_queue *cfq_close_cooperator(struct cfq_data *cfqd,
+ struct cfq_queue *cur_cfqq,
+ int probe)
{
+ struct cfq_queue *cfqq;
+
+ /*
+ * A valid cfq_io_context is necessary to compare requests against
+ * the seek_mean of the current cfqq.
+ */
+ if (!cfqd->active_cic)
+ return NULL;
+
/*
* We should notice if some of the queues are cooperating, eg
* working closely on the same area of the disk. In that case,
* we can group them together and don't waste time idling.
*/
- return 0;
+ cfqq = cfqq_close(cfqd, cur_cfqq);
+ if (!cfqq)
+ return NULL;
+
+ if (cfq_cfqq_coop(cfqq))
+ return NULL;
+
+ if (!probe)
+ cfq_mark_cfqq_coop(cfqq);
+ return cfqq;
}
+
#define CIC_SEEKY(cic) ((cic)->seek_mean > (8 * 1024))
static void cfq_arm_slice_timer(struct cfq_data *cfqd)
if (!cic || !atomic_read(&cic->ioc->nr_tasks))
return;
- /*
- * See if this prio level has a good candidate
- */
- if (cfq_close_cooperator(cfqd, cfqq) &&
- (sample_valid(cic->ttime_samples) && cic->ttime_mean > 2))
- return;
-
cfq_mark_cfqq_wait_request(cfqq);
/*
sl = min(sl, msecs_to_jiffies(CFQ_MIN_TT));
mod_timer(&cfqd->idle_slice_timer, jiffies + sl);
- cfq_log(cfqd, "arm_idle: %lu", sl);
+ cfq_log_cfqq(cfqd, cfqq, "arm_idle: %lu", sl);
}
/*
*/
static struct cfq_queue *cfq_select_queue(struct cfq_data *cfqd)
{
- struct cfq_queue *cfqq;
+ struct cfq_queue *cfqq, *new_cfqq = NULL;
cfqq = cfqd->active_queue;
if (!cfqq)
goto keep_queue;
/*
+ * If another queue has a request waiting within our mean seek
+ * distance, let it run. The expire code will check for close
+ * cooperators and put the close queue at the front of the service
+ * tree.
+ */
+ new_cfqq = cfq_close_cooperator(cfqd, cfqq, 0);
+ if (new_cfqq)
+ goto expire;
+
+ /*
* No requests pending. If the active queue still has requests in
* flight or is idling for a new request, allow either of these
* conditions to happen (or time out) before selecting a new queue.
expire:
cfq_slice_expired(cfqd, 0);
new_queue:
- cfqq = cfq_set_active_queue(cfqd);
+ cfqq = cfq_set_active_queue(cfqd, new_cfqq);
keep_queue:
return cfqq;
}
if (ioc->ioc_data == cic)
rcu_assign_pointer(ioc->ioc_data, NULL);
- if (cic->cfqq[ASYNC]) {
- cfq_exit_cfqq(cfqd, cic->cfqq[ASYNC]);
- cic->cfqq[ASYNC] = NULL;
+ if (cic->cfqq[BLK_RW_ASYNC]) {
+ cfq_exit_cfqq(cfqd, cic->cfqq[BLK_RW_ASYNC]);
+ cic->cfqq[BLK_RW_ASYNC] = NULL;
}
- if (cic->cfqq[SYNC]) {
- cfq_exit_cfqq(cfqd, cic->cfqq[SYNC]);
- cic->cfqq[SYNC] = NULL;
+ if (cic->cfqq[BLK_RW_SYNC]) {
+ cfq_exit_cfqq(cfqd, cic->cfqq[BLK_RW_SYNC]);
+ cic->cfqq[BLK_RW_SYNC] = NULL;
}
}
spin_lock_irqsave(cfqd->queue->queue_lock, flags);
- cfqq = cic->cfqq[ASYNC];
+ cfqq = cic->cfqq[BLK_RW_ASYNC];
if (cfqq) {
struct cfq_queue *new_cfqq;
- new_cfqq = cfq_get_queue(cfqd, ASYNC, cic->ioc, GFP_ATOMIC);
+ new_cfqq = cfq_get_queue(cfqd, BLK_RW_ASYNC, cic->ioc,
+ GFP_ATOMIC);
if (new_cfqq) {
- cic->cfqq[ASYNC] = new_cfqq;
+ cic->cfqq[BLK_RW_ASYNC] = new_cfqq;
cfq_put_queue(cfqq);
}
}
- cfqq = cic->cfqq[SYNC];
+ cfqq = cic->cfqq[BLK_RW_SYNC];
if (cfqq)
cfq_mark_cfqq_prio_changed(cfqq);
}
RB_CLEAR_NODE(&cfqq->rb_node);
+ RB_CLEAR_NODE(&cfqq->p_node);
INIT_LIST_HEAD(&cfqq->fifo);
atomic_set(&cfqq->ref, 0);
* Remember that we saw a request from this process, but
* don't start queuing just yet. Otherwise we risk seeing lots
* of tiny requests, because we disrupt the normal plugging
- * and merging.
+ * and merging. If the request is already larger than a single
+ * page, let it rip immediately. For that case we assume that
+ * merging is already done. Ditto for a busy system that
+ * has other work pending, don't risk delaying until the
+ * idle timer unplug to continue working.
*/
- if (cfq_cfqq_wait_request(cfqq))
+ if (cfq_cfqq_wait_request(cfqq)) {
+ if (blk_rq_bytes(rq) > PAGE_CACHE_SIZE ||
+ cfqd->busy_queues > 1) {
+ del_timer(&cfqd->idle_slice_timer);
+ blk_start_queueing(cfqd->queue);
+ }
cfq_mark_cfqq_must_dispatch(cfqq);
+ }
} else if (cfq_should_preempt(cfqd, cfqq, rq)) {
/*
* not the active queue - expire current slice if it is
* or if we want to idle in case it has no pending requests.
*/
if (cfqd->active_queue == cfqq) {
+ const bool cfqq_empty = RB_EMPTY_ROOT(&cfqq->sort_list);
+
if (cfq_cfqq_slice_new(cfqq)) {
cfq_set_prio_slice(cfqd, cfqq);
cfq_clear_cfqq_slice_new(cfqq);
}
+ /*
+ * If there are no requests waiting in this queue, and
+ * there are other queues ready to issue requests, AND
+ * those other queues are issuing requests within our
+ * mean seek distance, give them a chance to run instead
+ * of idling.
+ */
if (cfq_slice_used(cfqq) || cfq_class_idle(cfqq))
cfq_slice_expired(cfqd, 1);
- else if (sync && !rq_noidle(rq) &&
- RB_EMPTY_ROOT(&cfqq->sort_list)) {
+ else if (cfqq_empty && !cfq_close_cooperator(cfqd, cfqq, 1) &&
+ sync && !rq_noidle(rq))
cfq_arm_slice_timer(cfqd);
- }
}
if (!cfqd->rq_in_driver)
if (!cic)
return ELV_MQUEUE_MAY;
- cfqq = cic_to_cfqq(cic, rw & REQ_RW_SYNC);
+ cfqq = cic_to_cfqq(cic, rw_is_sync(rw));
if (cfqq) {
cfq_init_prio_data(cfqq, cic->ioc);
cfq_prio_boost(cfqq);
struct cfq_data *cfqd =
container_of(work, struct cfq_data, unplug_work);
struct request_queue *q = cfqd->queue;
- unsigned long flags;
- spin_lock_irqsave(q->queue_lock, flags);
+ spin_lock_irq(q->queue_lock);
blk_start_queueing(q);
- spin_unlock_irqrestore(q->queue_lock, flags);
+ spin_unlock_irq(q->queue_lock);
}
/*
/*
* Call with queue lock held, interrupts disabled
*/
-void elv_quisce_start(struct request_queue *q)
+void elv_quiesce_start(struct request_queue *q)
{
queue_flag_set(QUEUE_FLAG_ELVSWITCH, q);
}
}
-void elv_quisce_end(struct request_queue *q)
+void elv_quiesce_end(struct request_queue *q)
{
queue_flag_clear(QUEUE_FLAG_ELVSWITCH, q);
}
* Turn on BYPASS and drain all requests w/ elevator private data
*/
spin_lock_irq(q->queue_lock);
- elv_quisce_start(q);
+ elv_quiesce_start(q);
/*
* Remember old elevator.
*/
elevator_exit(old_elevator);
spin_lock_irq(q->queue_lock);
- elv_quisce_end(q);
+ elv_quiesce_end(q);
spin_unlock_irq(q->queue_lock);
blk_add_trace_msg(q, "elv switch: %s", e->elevator_type->elevator_name);
struct bio *bio;
bio = bio_alloc(GFP_KERNEL, 0);
- if (!bio)
- return -ENOMEM;
bio->bi_end_io = blk_ioc_discard_endio;
bio->bi_bdev = bdev;
static int blk_complete_sghdr_rq(struct request *rq, struct sg_io_hdr *hdr,
struct bio *bio)
{
- int ret = 0;
+ int r, ret = 0;
/*
* fill in all the output members
ret = -EFAULT;
}
- blk_rq_unmap_user(bio);
+ r = blk_rq_unmap_user(bio);
+ if (!ret)
+ ret = r;
blk_put_request(rq);
return ret;
*
* We follow the current spec and consider that 0x69/0x96
* identifies a port multiplier and 0x3c/0xc3 a SEMB device.
+ * Unfortunately, WDC WD1600JS-62MHB5 (a hard drive) reports
+ * SEMB signature. This is worked around in
+ * ata_dev_read_id().
*/
if ((tf->lbam == 0) && (tf->lbah == 0)) {
DPRINTK("found ATA device by sig\n");
}
if ((tf->lbam == 0x3c) && (tf->lbah == 0xc3)) {
- printk(KERN_INFO "ata: SEMB device ignored\n");
- return ATA_DEV_SEMB_UNSUP; /* not yet */
+ DPRINTK("found SEMB device by sig (could be ATA device)\n");
+ return ATA_DEV_SEMB;
}
DPRINTK("unknown device\n");
/*
* Process compact flash extended modes
*/
- int pio = id[163] & 0x7;
- int dma = (id[163] >> 3) & 7;
+ int pio = (id[ATA_ID_CFA_MODES] >> 0) & 0x7;
+ int dma = (id[ATA_ID_CFA_MODES] >> 3) & 0x7;
if (pio)
pio_mask |= (1 << 5);
struct ata_taskfile tf;
unsigned int err_mask = 0;
const char *reason;
+ bool is_semb = class == ATA_DEV_SEMB;
int may_fallback = 1, tried_spinup = 0;
int rc;
ata_tf_init(dev, &tf);
switch (class) {
+ case ATA_DEV_SEMB:
+ class = ATA_DEV_ATA; /* some hard drives report SEMB sig */
case ATA_DEV_ATA:
tf.command = ATA_CMD_ID_ATA;
break;
return -ENOENT;
}
+ if (is_semb) {
+ ata_dev_printk(dev, KERN_INFO, "IDENTIFY failed on "
+ "device w/ SEMB sig, disabled\n");
+ /* SEMB is not supported yet */
+ *p_class = ATA_DEV_SEMB_UNSUP;
+ return 0;
+ }
+
if ((err_mask == AC_ERR_DEV) && (tf.feature & ATA_ABORTED)) {
/* Device or controller might have reported
* the wrong device class. Give a shot at the
/* ATA-specific feature tests */
if (dev->class == ATA_DEV_ATA) {
if (ata_id_is_cfa(id)) {
- if (id[162] & 1) /* CPRM may make this media unusable */
+ /* CPRM may make this media unusable */
+ if (id[ATA_ID_CFA_KEY_MGMT] & 1)
ata_dev_printk(dev, KERN_WARNING,
"supports DRM functions and may "
"not be fully accessable.\n");
return rc;
}
+static int ata_ioc32(struct ata_port *ap)
+{
+ if (ap->flags & ATA_FLAG_PIO_DMA)
+ return 1;
+ if (ap->pflags & ATA_PFLAG_PIO32)
+ return 1;
+ return 0;
+}
+
int ata_sas_scsi_ioctl(struct ata_port *ap, struct scsi_device *scsidev,
int cmd, void __user *arg)
{
int val = -EINVAL, rc = -EINVAL;
+ unsigned long flags;
switch (cmd) {
case ATA_IOC_GET_IO32:
- val = 0;
+ spin_lock_irqsave(ap->lock, flags);
+ val = ata_ioc32(ap);
+ spin_unlock_irqrestore(ap->lock, flags);
if (copy_to_user(arg, &val, 1))
return -EFAULT;
return 0;
case ATA_IOC_SET_IO32:
val = (unsigned long) arg;
- if (val != 0)
- return -EINVAL;
- return 0;
+ rc = 0;
+ spin_lock_irqsave(ap->lock, flags);
+ if (ap->pflags & ATA_PFLAG_PIO32CHANGE) {
+ if (val)
+ ap->pflags |= ATA_PFLAG_PIO32;
+ else
+ ap->pflags &= ~ATA_PFLAG_PIO32;
+ } else {
+ if (val != ata_ioc32(ap))
+ rc = -EINVAL;
+ }
+ spin_unlock_irqrestore(ap->lock, flags);
+ return rc;
case HDIO_GET_IDENTITY:
return ata_get_identity(ap, scsidev, arg);
.inherits = &ata_bmdma_port_ops,
.sff_data_xfer = ata_sff_data_xfer32,
+ .port_start = ata_sff_port_start32,
};
EXPORT_SYMBOL_GPL(ata_bmdma32_port_ops);
void __iomem *data_addr = ap->ioaddr.data_addr;
unsigned int words = buflen >> 2;
int slop = buflen & 3;
+
+ if (!(ap->pflags & ATA_PFLAG_PIO32))
+ return ata_sff_data_xfer(dev, buf, buflen, rw);
/* Transfer multiple of 4 bytes */
if (rw == READ)
EXPORT_SYMBOL_GPL(ata_sff_port_start);
/**
+ * ata_sff_port_start32 - Set port up for dma.
+ * @ap: Port to initialize
+ *
+ * Called just after data structures for each port are
+ * initialized. Allocates space for PRD table if the device
+ * is DMA capable SFF.
+ *
+ * May be used as the port_start() entry in ata_port_operations for
+ * devices that are capable of 32bit PIO.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+int ata_sff_port_start32(struct ata_port *ap)
+{
+ ap->pflags |= ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE;
+ if (ap->ioaddr.bmdma_addr)
+ return ata_port_start(ap);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sff_port_start32);
+
+/**
* ata_sff_std_ports - initialize ioaddr with standard port offsets.
* @ioaddr: IO address structure to be initialized
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
- * Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
+ * Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
*
* TODO
* Look into engine reset on timeout errors. Should not be required.
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
-#define DRV_VERSION "0.6.11"
+#define DRV_VERSION "0.6.12"
struct hpt_clock {
u8 xfer_speed;
}
/**
- * hpt370_bmdma_start - DMA engine begin
- * @qc: ATA command
- *
- * The 370 and 370A want us to reset the DMA engine each time we
- * use it. The 372 and later are fine.
- */
-
-static void hpt370_bmdma_start(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
- udelay(10);
- ata_bmdma_start(qc);
-}
-
-/**
* hpt370_bmdma_end - DMA engine stop
* @qc: ATA command
*
static struct ata_port_operations hpt370_port_ops = {
.inherits = &ata_bmdma_port_ops,
- .bmdma_start = hpt370_bmdma_start,
.bmdma_stop = hpt370_bmdma_stop,
.mode_filter = hpt370_filter,
struct ata_port_operations *ops;
unsigned int pio_mask;
unsigned int flags;
+ unsigned int pflags;
int (*setup)(struct platform_device *, struct legacy_probe *probe,
struct legacy_data *data);
};
unsigned char *buf, unsigned int buflen, int rw)
{
int slop = buflen & 3;
+ struct ata_port *ap = dev->link->ap;
+
/* 32bit I/O capable *and* we need to write a whole number of dwords */
- if (ata_id_has_dword_io(dev->id) && (slop == 0 || slop == 3)) {
- struct ata_port *ap = dev->link->ap;
+ if (ata_id_has_dword_io(dev->id) && (slop == 0 || slop == 3)
+ && (ap->pflags & ATA_PFLAG_PIO32)) {
unsigned long flags;
local_irq_save(flags);
struct ata_port *ap = adev->link->ap;
int slop = buflen & 3;
- if (ata_id_has_dword_io(adev->id) && (slop == 0 || slop == 3)) {
+ if (ata_id_has_dword_io(adev->id) && (slop == 0 || slop == 3)
+ && (ap->pflags & ATA_PFLAG_PIO32)) {
if (rw == WRITE)
iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
else
static struct legacy_controller controllers[] = {
{"BIOS", &legacy_port_ops, 0x1F,
- ATA_FLAG_NO_IORDY, NULL },
+ ATA_FLAG_NO_IORDY, 0, NULL },
{"Snooping", &simple_port_ops, 0x1F,
- 0 , NULL },
+ 0, 0, NULL },
{"PDC20230", &pdc20230_port_ops, 0x7,
- ATA_FLAG_NO_IORDY, NULL },
+ ATA_FLAG_NO_IORDY,
+ ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE, NULL },
{"HT6560A", &ht6560a_port_ops, 0x07,
- ATA_FLAG_NO_IORDY, NULL },
+ ATA_FLAG_NO_IORDY, 0, NULL },
{"HT6560B", &ht6560b_port_ops, 0x1F,
- ATA_FLAG_NO_IORDY, NULL },
+ ATA_FLAG_NO_IORDY, 0, NULL },
{"OPTI82C611A", &opti82c611a_port_ops, 0x0F,
- 0 , NULL },
+ 0, 0, NULL },
{"OPTI82C46X", &opti82c46x_port_ops, 0x0F,
- 0 , NULL },
+ 0, 0, NULL },
{"QDI6500", &qdi6500_port_ops, 0x07,
- ATA_FLAG_NO_IORDY, qdi_port },
+ ATA_FLAG_NO_IORDY,
+ ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE, qdi_port },
{"QDI6580", &qdi6580_port_ops, 0x1F,
- 0 , qdi_port },
+ 0, ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE, qdi_port },
{"QDI6580DP", &qdi6580dp_port_ops, 0x1F,
- 0 , qdi_port },
+ 0, ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE, qdi_port },
{"W83759A", &winbond_port_ops, 0x1F,
- 0 , winbond_port }
+ 0, ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE,
+ winbond_port }
};
/**
ap->ops = ops;
ap->pio_mask = pio_modes;
ap->flags |= ATA_FLAG_SLAVE_POSS | iordy;
+ ap->pflags |= controller->pflags;
ap->ioaddr.cmd_addr = io_addr;
ap->ioaddr.altstatus_addr = ctrl_addr;
ap->ioaddr.ctl_addr = ctrl_addr;
return 0;
}
}
+ ata_host_detach(host);
fail:
platform_device_unregister(pdev);
return ret;
#include <linux/libata.h>
#define DRV_NAME "pata_ninja32"
-#define DRV_VERSION "0.1.3"
+#define DRV_VERSION "0.1.5"
/**
.sff_dev_select = ninja32_dev_select,
.cable_detect = ata_cable_40wire,
.set_piomode = ninja32_set_piomode,
+ .sff_data_xfer = ata_sff_data_xfer32
};
static void ninja32_program(void __iomem *base)
ap->ioaddr.altstatus_addr = base + 0x1E;
ap->ioaddr.bmdma_addr = base;
ata_sff_std_ports(&ap->ioaddr);
+ ap->pflags = ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE;
ninja32_program(base);
/* FIXME: Should we disable them at remove ? */
#include <linux/dmi.h>
#define DRV_NAME "pata_via"
-#define DRV_VERSION "0.3.3"
+#define DRV_VERSION "0.3.4"
/*
* The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
{ NULL }
};
+struct via_port {
+ u8 cached_device;
+};
/*
* Cable special cases
*/
static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
{
- struct ata_taskfile tmp_tf;
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ struct via_port *vp = ap->private_data;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+ int newctl = 0;
+
+ if (tf->ctl != ap->last_ctl) {
+ iowrite8(tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ newctl = 1;
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE) {
+ iowrite8(tf->device, ioaddr->device_addr);
+ vp->cached_device = tf->device;
+ } else if (newctl)
+ iowrite8(vp->cached_device, ioaddr->device_addr);
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ WARN_ON_ONCE(!ioaddr->ctl_addr);
+ iowrite8(tf->hob_feature, ioaddr->feature_addr);
+ iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
+ iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
+ iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
+ iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
+ VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
+ tf->hob_feature,
+ tf->hob_nsect,
+ tf->hob_lbal,
+ tf->hob_lbam,
+ tf->hob_lbah);
+ }
- if (ap->ctl != ap->last_ctl && !(tf->flags & ATA_TFLAG_DEVICE)) {
- tmp_tf = *tf;
- tmp_tf.flags |= ATA_TFLAG_DEVICE;
- tf = &tmp_tf;
+ if (is_addr) {
+ iowrite8(tf->feature, ioaddr->feature_addr);
+ iowrite8(tf->nsect, ioaddr->nsect_addr);
+ iowrite8(tf->lbal, ioaddr->lbal_addr);
+ iowrite8(tf->lbam, ioaddr->lbam_addr);
+ iowrite8(tf->lbah, ioaddr->lbah_addr);
+ VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
}
- ata_sff_tf_load(ap, tf);
+
+ ata_wait_idle(ap);
+}
+
+static int via_port_start(struct ata_port *ap)
+{
+ struct via_port *vp;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ int ret = ata_sff_port_start(ap);
+ if (ret < 0)
+ return ret;
+
+ vp = devm_kzalloc(&pdev->dev, sizeof(struct via_port), GFP_KERNEL);
+ if (vp == NULL)
+ return -ENOMEM;
+ ap->private_data = vp;
+ return 0;
}
static struct scsi_host_template via_sht = {
.set_dmamode = via_set_dmamode,
.prereset = via_pre_reset,
.sff_tf_load = via_tf_load,
+ .port_start = via_port_start,
};
static struct ata_port_operations via_port_ops_noirq = {
return status;
}
+static void mv_rw_multi_errata_sata24(struct ata_queued_cmd *qc)
+{
+ struct ata_taskfile *tf = &qc->tf;
+ /*
+ * Workaround for 88SX60x1 FEr SATA#24.
+ *
+ * Chip may corrupt WRITEs if multi_count >= 4kB.
+ * Note that READs are unaffected.
+ *
+ * It's not clear if this errata really means "4K bytes",
+ * or if it always happens for multi_count > 7
+ * regardless of device sector_size.
+ *
+ * So, for safety, any write with multi_count > 7
+ * gets converted here into a regular PIO write instead:
+ */
+ if ((tf->flags & ATA_TFLAG_WRITE) && is_multi_taskfile(tf)) {
+ if (qc->dev->multi_count > 7) {
+ switch (tf->command) {
+ case ATA_CMD_WRITE_MULTI:
+ tf->command = ATA_CMD_PIO_WRITE;
+ break;
+ case ATA_CMD_WRITE_MULTI_FUA_EXT:
+ tf->flags &= ~ATA_TFLAG_FUA; /* ugh */
+ /* fall through */
+ case ATA_CMD_WRITE_MULTI_EXT:
+ tf->command = ATA_CMD_PIO_WRITE_EXT;
+ break;
+ }
+ }
+ }
+}
+
/**
* mv_qc_prep - Host specific command preparation.
* @qc: queued command to prepare
struct ata_port *ap = qc->ap;
struct mv_port_priv *pp = ap->private_data;
__le16 *cw;
- struct ata_taskfile *tf;
+ struct ata_taskfile *tf = &qc->tf;
u16 flags = 0;
unsigned in_index;
- if ((qc->tf.protocol != ATA_PROT_DMA) &&
- (qc->tf.protocol != ATA_PROT_NCQ))
+ switch (tf->protocol) {
+ case ATA_PROT_DMA:
+ case ATA_PROT_NCQ:
+ break; /* continue below */
+ case ATA_PROT_PIO:
+ mv_rw_multi_errata_sata24(qc);
+ return;
+ default:
return;
+ }
/* Fill in command request block
*/
- if (!(qc->tf.flags & ATA_TFLAG_WRITE))
+ if (!(tf->flags & ATA_TFLAG_WRITE))
flags |= CRQB_FLAG_READ;
WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
flags |= qc->tag << CRQB_TAG_SHIFT;
pp->crqb[in_index].ctrl_flags = cpu_to_le16(flags);
cw = &pp->crqb[in_index].ata_cmd[0];
- tf = &qc->tf;
/* Sadly, the CRQB cannot accomodate all registers--there are
* only 11 bytes...so we must pick and choose required
struct ata_port *ap = qc->ap;
struct mv_port_priv *pp = ap->private_data;
struct mv_crqb_iie *crqb;
- struct ata_taskfile *tf;
+ struct ata_taskfile *tf = &qc->tf;
unsigned in_index;
u32 flags = 0;
- if ((qc->tf.protocol != ATA_PROT_DMA) &&
- (qc->tf.protocol != ATA_PROT_NCQ))
+ if ((tf->protocol != ATA_PROT_DMA) &&
+ (tf->protocol != ATA_PROT_NCQ))
return;
/* Fill in Gen IIE command request block */
- if (!(qc->tf.flags & ATA_TFLAG_WRITE))
+ if (!(tf->flags & ATA_TFLAG_WRITE))
flags |= CRQB_FLAG_READ;
WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma[qc->tag] >> 16) >> 16);
crqb->flags = cpu_to_le32(flags);
- tf = &qc->tf;
crqb->ata_cmd[0] = cpu_to_le32(
(tf->command << 16) |
(tf->feature << 24)
static inline int driver_match_device(struct device_driver *drv,
struct device *dev)
{
- return drv->bus->match && drv->bus->match(dev, drv);
+ return drv->bus->match ? drv->bus->match(dev, drv) : 1;
}
extern void sysdev_shutdown(void);
struct device *child;
int error = 0;
+ if (!parent->p)
+ return 0;
+
klist_iter_init(&parent->p->klist_children, &i);
while ((child = next_device(&i)) && !error)
error = fn(child, data);
{
int error;
+ early_platform_cleanup();
+
error = device_register(&platform_bus);
if (error)
return error;
}
EXPORT_SYMBOL_GPL(dma_get_required_mask);
#endif
+
+static __initdata LIST_HEAD(early_platform_driver_list);
+static __initdata LIST_HEAD(early_platform_device_list);
+
+/**
+ * early_platform_driver_register
+ * @edrv: early_platform driver structure
+ * @buf: string passed from early_param()
+ */
+int __init early_platform_driver_register(struct early_platform_driver *epdrv,
+ char *buf)
+{
+ unsigned long index;
+ int n;
+
+ /* Simply add the driver to the end of the global list.
+ * Drivers will by default be put on the list in compiled-in order.
+ */
+ if (!epdrv->list.next) {
+ INIT_LIST_HEAD(&epdrv->list);
+ list_add_tail(&epdrv->list, &early_platform_driver_list);
+ }
+
+ /* If the user has specified device then make sure the driver
+ * gets prioritized. The driver of the last device specified on
+ * command line will be put first on the list.
+ */
+ n = strlen(epdrv->pdrv->driver.name);
+ if (buf && !strncmp(buf, epdrv->pdrv->driver.name, n)) {
+ list_move(&epdrv->list, &early_platform_driver_list);
+
+ if (!strcmp(buf, epdrv->pdrv->driver.name))
+ epdrv->requested_id = -1;
+ else if (buf[n] == '.' && strict_strtoul(&buf[n + 1], 10,
+ &index) == 0)
+ epdrv->requested_id = index;
+ else
+ epdrv->requested_id = EARLY_PLATFORM_ID_ERROR;
+ }
+
+ return 0;
+}
+
+/**
+ * early_platform_add_devices - add a numbers of early platform devices
+ * @devs: array of early platform devices to add
+ * @num: number of early platform devices in array
+ */
+void __init early_platform_add_devices(struct platform_device **devs, int num)
+{
+ struct device *dev;
+ int i;
+
+ /* simply add the devices to list */
+ for (i = 0; i < num; i++) {
+ dev = &devs[i]->dev;
+
+ if (!dev->devres_head.next) {
+ INIT_LIST_HEAD(&dev->devres_head);
+ list_add_tail(&dev->devres_head,
+ &early_platform_device_list);
+ }
+ }
+}
+
+/**
+ * early_platform_driver_register_all
+ * @class_str: string to identify early platform driver class
+ */
+void __init early_platform_driver_register_all(char *class_str)
+{
+ /* The "class_str" parameter may or may not be present on the kernel
+ * command line. If it is present then there may be more than one
+ * matching parameter.
+ *
+ * Since we register our early platform drivers using early_param()
+ * we need to make sure that they also get registered in the case
+ * when the parameter is missing from the kernel command line.
+ *
+ * We use parse_early_options() to make sure the early_param() gets
+ * called at least once. The early_param() may be called more than
+ * once since the name of the preferred device may be specified on
+ * the kernel command line. early_platform_driver_register() handles
+ * this case for us.
+ */
+ parse_early_options(class_str);
+}
+
+/**
+ * early_platform_match
+ * @edrv: early platform driver structure
+ * @id: id to match against
+ */
+static __init struct platform_device *
+early_platform_match(struct early_platform_driver *epdrv, int id)
+{
+ struct platform_device *pd;
+
+ list_for_each_entry(pd, &early_platform_device_list, dev.devres_head)
+ if (platform_match(&pd->dev, &epdrv->pdrv->driver))
+ if (pd->id == id)
+ return pd;
+
+ return NULL;
+}
+
+/**
+ * early_platform_left
+ * @edrv: early platform driver structure
+ * @id: return true if id or above exists
+ */
+static __init int early_platform_left(struct early_platform_driver *epdrv,
+ int id)
+{
+ struct platform_device *pd;
+
+ list_for_each_entry(pd, &early_platform_device_list, dev.devres_head)
+ if (platform_match(&pd->dev, &epdrv->pdrv->driver))
+ if (pd->id >= id)
+ return 1;
+
+ return 0;
+}
+
+/**
+ * early_platform_driver_probe_id
+ * @class_str: string to identify early platform driver class
+ * @id: id to match against
+ * @nr_probe: number of platform devices to successfully probe before exiting
+ */
+static int __init early_platform_driver_probe_id(char *class_str,
+ int id,
+ int nr_probe)
+{
+ struct early_platform_driver *epdrv;
+ struct platform_device *match;
+ int match_id;
+ int n = 0;
+ int left = 0;
+
+ list_for_each_entry(epdrv, &early_platform_driver_list, list) {
+ /* only use drivers matching our class_str */
+ if (strcmp(class_str, epdrv->class_str))
+ continue;
+
+ if (id == -2) {
+ match_id = epdrv->requested_id;
+ left = 1;
+
+ } else {
+ match_id = id;
+ left += early_platform_left(epdrv, id);
+
+ /* skip requested id */
+ switch (epdrv->requested_id) {
+ case EARLY_PLATFORM_ID_ERROR:
+ case EARLY_PLATFORM_ID_UNSET:
+ break;
+ default:
+ if (epdrv->requested_id == id)
+ match_id = EARLY_PLATFORM_ID_UNSET;
+ }
+ }
+
+ switch (match_id) {
+ case EARLY_PLATFORM_ID_ERROR:
+ pr_warning("%s: unable to parse %s parameter\n",
+ class_str, epdrv->pdrv->driver.name);
+ /* fall-through */
+ case EARLY_PLATFORM_ID_UNSET:
+ match = NULL;
+ break;
+ default:
+ match = early_platform_match(epdrv, match_id);
+ }
+
+ if (match) {
+ if (epdrv->pdrv->probe(match))
+ pr_warning("%s: unable to probe %s early.\n",
+ class_str, match->name);
+ else
+ n++;
+ }
+
+ if (n >= nr_probe)
+ break;
+ }
+
+ if (left)
+ return n;
+ else
+ return -ENODEV;
+}
+
+/**
+ * early_platform_driver_probe
+ * @class_str: string to identify early platform driver class
+ * @nr_probe: number of platform devices to successfully probe before exiting
+ * @user_only: only probe user specified early platform devices
+ */
+int __init early_platform_driver_probe(char *class_str,
+ int nr_probe,
+ int user_only)
+{
+ int k, n, i;
+
+ n = 0;
+ for (i = -2; n < nr_probe; i++) {
+ k = early_platform_driver_probe_id(class_str, i, nr_probe - n);
+
+ if (k < 0)
+ break;
+
+ n += k;
+
+ if (user_only)
+ break;
+ }
+
+ return n;
+}
+
+/**
+ * early_platform_cleanup - clean up early platform code
+ */
+void __init early_platform_cleanup(void)
+{
+ struct platform_device *pd, *pd2;
+
+ /* clean up the devres list used to chain devices */
+ list_for_each_entry_safe(pd, pd2, &early_platform_device_list,
+ dev.devres_head) {
+ list_del(&pd->dev.devres_head);
+ memset(&pd->dev.devres_head, 0, sizeof(pd->dev.devres_head));
+ }
+}
+
if (rw == READ) {
copy_from_brd(mem + off, brd, sector, len);
flush_dcache_page(page);
- } else
+ } else {
+ flush_dcache_page(page);
copy_to_brd(brd, mem + off, sector, len);
+ }
kunmap_atomic(mem, KM_USER0);
out:
if (!brd->brd_queue)
goto out_free_dev;
blk_queue_make_request(brd->brd_queue, brd_make_request);
+ blk_queue_ordered(brd->brd_queue, QUEUE_ORDERED_TAG, NULL);
blk_queue_max_sectors(brd->brd_queue, 1024);
blk_queue_bounce_limit(brd->brd_queue, BLK_BOUNCE_ANY);
{
struct urb *urb = &sc->work_urb;
struct bulk_cs_wrap *bcs;
+ int endp;
int len;
int rc;
return;
}
+ endp = usb_pipeendpoint(sc->last_pipe);
+ if (usb_pipein(sc->last_pipe))
+ endp |= USB_DIR_IN;
+
if (cmd->state == UB_CMDST_CLEAR) {
if (urb->status == -EPIPE) {
/*
* We ignore the result for the halt clear.
*/
- /* reset the endpoint toggle */
- usb_settoggle(sc->dev, usb_pipeendpoint(sc->last_pipe),
- usb_pipeout(sc->last_pipe), 0);
+ usb_reset_endpoint(sc->dev, endp);
ub_state_sense(sc, cmd);
* We ignore the result for the halt clear.
*/
- /* reset the endpoint toggle */
- usb_settoggle(sc->dev, usb_pipeendpoint(sc->last_pipe),
- usb_pipeout(sc->last_pipe), 0);
+ usb_reset_endpoint(sc->dev, endp);
ub_state_stat(sc, cmd);
* We ignore the result for the halt clear.
*/
- /* reset the endpoint toggle */
- usb_settoggle(sc->dev, usb_pipeendpoint(sc->last_pipe),
- usb_pipeout(sc->last_pipe), 0);
+ usb_reset_endpoint(sc->dev, endp);
ub_state_stat_counted(sc, cmd);
del_timer_sync(&timer);
usb_kill_urb(&sc->work_urb);
- /* reset the endpoint toggle */
- usb_settoggle(sc->dev, endp, usb_pipeout(sc->last_pipe), 0);
+ usb_reset_endpoint(sc->dev, endp);
return 0;
}
}
#endif
-void __attribute__((weak))
-map_devmem(unsigned long pfn, unsigned long len, pgprot_t prot)
-{
- /* nothing. architectures can override. */
-}
-
-void __attribute__((weak))
-unmap_devmem(unsigned long pfn, unsigned long len, pgprot_t prot)
-{
- /* nothing. architectures can override. */
-}
-
-static void mmap_mem_open(struct vm_area_struct *vma)
-{
- map_devmem(vma->vm_pgoff, vma->vm_end - vma->vm_start,
- vma->vm_page_prot);
-}
-
-static void mmap_mem_close(struct vm_area_struct *vma)
-{
- unmap_devmem(vma->vm_pgoff, vma->vm_end - vma->vm_start,
- vma->vm_page_prot);
-}
-
static struct vm_operations_struct mmap_mem_ops = {
- .open = mmap_mem_open,
- .close = mmap_mem_close,
#ifdef CONFIG_HAVE_IOREMAP_PROT
.access = generic_access_phys
#endif
vma->vm_pgoff,
size,
vma->vm_page_prot)) {
- unmap_devmem(vma->vm_pgoff, size, vma->vm_page_prot);
return -EAGAIN;
}
return 0;
continue; /* nothing to display */
}
/* Glyph not found */
- if ((!(vc->vc_utf && !vc->vc_disp_ctrl) && c < 128) && !(c & ~charmask)) {
+ if ((!(vc->vc_utf && !vc->vc_disp_ctrl) || c < 128) && !(c & ~charmask)) {
/* In legacy mode use the glyph we get by a 1:1 mapping.
This would make absolutely no sense with Unicode in mind,
but do this for ASCII characters since a font may lack
.dma_test_irq = ide_dma_test_irq,
.dma_lost_irq = ide_dma_lost_irq,
.dma_timer_expiry = ide_dma_sff_timer_expiry,
+ .dma_sff_read_status = ide_dma_sff_read_status,
};
static const struct ide_port_info cs5536_info = {
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
* Portions Copyright (C) 2007 Bartlomiej Zolnierkiewicz
- * Portions Copyright (C) 2005-2008 MontaVista Software, Inc.
+ * Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
*
* Thanks to HighPoint Technologies for their assistance, and hardware.
* Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his
* the register setting lists into the table indexed by the clock selected
* - set the correct hwif->ultra_mask for each individual chip
* - add Ultra and MW DMA mode filtering for the HPT37[24] based SATA cards
+ * - stop resetting HPT370's state machine before each DMA transfer as that has
+ * caused more harm than good
* Sergei Shtylyov, <sshtylyov@ru.mvista.com> or <source@mvista.com>
*/
#define DRV_NAME "hpt366"
/* various tuning parameters */
-#define HPT_RESET_STATE_ENGINE
+#undef HPT_RESET_STATE_ENGINE
#undef HPT_DELAY_INTERRUPT
static const char *quirk_drives[] = {
/* get DMA command mode */
dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
/* stop DMA */
- outb(dma_cmd & ~0x1, hwif->dma_base + ATA_DMA_CMD);
+ outb(dma_cmd & ~ATA_DMA_START, hwif->dma_base + ATA_DMA_CMD);
hpt370_clear_engine(drive);
}
ide_hwif_t *hwif = drive->hwif;
u8 dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
- if (dma_stat & 0x01) {
+ if (dma_stat & ATA_DMA_ACTIVE) {
/* wait a little */
udelay(20);
dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
- if (dma_stat & 0x01)
+ if (dma_stat & ATA_DMA_ACTIVE)
hpt370_irq_timeout(drive);
}
return ide_dma_end(drive);
dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
/* return 1 if INTR asserted */
- if (dma_stat & 4)
+ if (dma_stat & ATA_DMA_INTR)
return 1;
return 0;
drive->dev_flags |= IDE_DFLAG_PARKED;
}
- if (rq && rq->cmd_type == REQ_TYPE_ATA_TASKFILE)
- memcpy(rq->special, cmd, sizeof(*cmd));
+ if (rq && rq->cmd_type == REQ_TYPE_ATA_TASKFILE) {
+ struct ide_cmd *orig_cmd = rq->special;
- if (cmd->tf_flags & IDE_TFLAG_DYN)
- kfree(cmd);
+ if (cmd->tf_flags & IDE_TFLAG_DYN)
+ kfree(orig_cmd);
+ else
+ memcpy(orig_cmd, cmd, sizeof(*cmd));
+ }
}
/* obsolete, blk_rq_bytes() should be used instead */
* The +2 is +1 for the stop command and +1 to allow for
* aligning the start address to a multiple of 16 bytes.
*/
- pmif->dma_table_cpu = (struct dbdma_cmd*)pci_alloc_consistent(
+ pmif->dma_table_cpu = pci_alloc_consistent(
dev,
(MAX_DCMDS + 2) * sizeof(struct dbdma_cmd),
&hwif->dmatable_dma);
static struct bus_type gameport_bus;
-static void gameport_add_driver(struct gameport_driver *drv);
static void gameport_add_port(struct gameport *gameport);
-static void gameport_destroy_port(struct gameport *gameport);
+static void gameport_attach_driver(struct gameport_driver *drv);
static void gameport_reconnect_port(struct gameport *gameport);
static void gameport_disconnect_port(struct gameport *gameport);
enum gameport_event_type {
GAMEPORT_REGISTER_PORT,
- GAMEPORT_REGISTER_DRIVER,
GAMEPORT_ATTACH_DRIVER,
};
gameport_add_port(event->object);
break;
- case GAMEPORT_REGISTER_DRIVER:
- gameport_add_driver(event->object);
+ case GAMEPORT_ATTACH_DRIVER:
+ gameport_attach_driver(event->object);
break;
default:
return 0;
}
-static void gameport_add_driver(struct gameport_driver *drv)
+static void gameport_attach_driver(struct gameport_driver *drv)
{
int error;
- error = driver_register(&drv->driver);
+ error = driver_attach(&drv->driver);
if (error)
printk(KERN_ERR
- "gameport: driver_register() failed for %s, error: %d\n",
+ "gameport: driver_attach() failed for %s, error: %d\n",
drv->driver.name, error);
}
return error;
list_add_tail_rcu(&handle->d_node, &dev->h_list);
mutex_unlock(&dev->mutex);
- synchronize_rcu();
/*
* Since we are supposed to be called from ->connect()
};
/*
- * Samsung NC10 with Fn+F? key release not working
+ * Samsung NC10,NC20 with Fn+F? key release not working
*/
static unsigned int atkbd_samsung_forced_release_keys[] = {
0x82, 0x83, 0x84, 0x86, 0x88, 0x89, 0xb3, 0xf7, 0xf9, -1U
.driver_data = atkbd_samsung_forced_release_keys,
},
{
+ .ident = "Samsung NC20",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "SAMSUNG ELECTRONICS CO., LTD."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "NC20"),
+ },
+ .callback = atkbd_setup_forced_release,
+ .driver_data = atkbd_samsung_forced_release_keys,
+ },
+ {
+ .ident = "Samsung SQ45S70S",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "SAMSUNG ELECTRONICS CO., LTD."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "SQ45S70S"),
+ },
+ .callback = atkbd_setup_forced_release,
+ .driver_data = atkbd_samsung_forced_release_keys,
+ },
+ {
.ident = "Fujitsu Amilo PA 1510",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"),
}
error = request_irq(bf54x_kpad->irq, bfin_kpad_isr,
- IRQF_SAMPLE_RANDOM, DRV_NAME, pdev);
+ 0, DRV_NAME, pdev);
if (error) {
printk(KERN_ERR DRV_NAME
": unable to claim irq %d; error %d\n",
config HP_SDC_RTC
tristate "HP SDC Real Time Clock"
- depends on GSC || HP300
+ depends on (GSC || HP300) && SERIO
select HP_SDC
help
Say Y here if you want to support the built-in real time clock
*/
static int __init pc110pad_init(void)
{
- struct pci_dev *dev;
int err;
if (!no_pci_devices())
{ }
};
+static struct dmi_system_id __initdata i8042_dmi_reset_table[] = {
+ {
+ .ident = "MSI Wind U-100",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_NAME, "U-100"),
+ DMI_MATCH(DMI_BOARD_VENDOR, "MICRO-STAR INTERNATIONAL CO., LTD"),
+ },
+ },
+ {
+ .ident = "LG Electronics X110",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_NAME, "X110"),
+ DMI_MATCH(DMI_BOARD_VENDOR, "LG Electronics Inc."),
+ },
+ },
+ { }
+};
+
#ifdef CONFIG_PNP
static struct dmi_system_id __initdata i8042_dmi_nopnp_table[] = {
{
DMI_MATCH(DMI_BOARD_VENDOR, "Intel Corporation"),
},
},
+ {
+ .ident = "MSI Wind U-100",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_NAME, "U-100"),
+ DMI_MATCH(DMI_BOARD_VENDOR, "MICRO-STAR INTERNATIONAL CO., LTD"),
+ },
+ },
{ }
};
#endif
#endif
#ifdef CONFIG_X86
+ if (dmi_check_system(i8042_dmi_reset_table))
+ i8042_reset = 1;
+
if (dmi_check_system(i8042_dmi_noloop_table))
i8042_noloop = 1;
static int i8042_controller_selftest(void)
{
unsigned char param;
+ int i = 0;
if (!i8042_reset)
return 0;
- if (i8042_command(¶m, I8042_CMD_CTL_TEST)) {
- printk(KERN_ERR "i8042.c: i8042 controller self test timeout.\n");
- return -ENODEV;
- }
+ /*
+ * We try this 5 times; on some really fragile systems this does not
+ * take the first time...
+ */
+ do {
+
+ if (i8042_command(¶m, I8042_CMD_CTL_TEST)) {
+ printk(KERN_ERR "i8042.c: i8042 controller self test timeout.\n");
+ return -ENODEV;
+ }
+
+ if (param == I8042_RET_CTL_TEST)
+ return 0;
- if (param != I8042_RET_CTL_TEST) {
printk(KERN_ERR "i8042.c: i8042 controller selftest failed. (%#x != %#x)\n",
- param, I8042_RET_CTL_TEST);
- return -EIO;
- }
+ param, I8042_RET_CTL_TEST);
+ msleep(50);
+ } while (i++ < 5);
+#ifdef CONFIG_X86
+ /*
+ * On x86, we don't fail entire i8042 initialization if controller
+ * reset fails in hopes that keyboard port will still be functional
+ * and user will still get a working keyboard. This is especially
+ * important on netbooks. On other arches we trust hardware more.
+ */
+ printk(KERN_INFO
+ "i8042: giving up on controller selftest, continuing anyway...\n");
return 0;
+#else
+ return -EIO;
+#endif
}
/*
/* Request AD7877 /DAV GPIO interrupt */
- err = request_irq(spi->irq, ad7877_irq, IRQF_TRIGGER_FALLING |
- IRQF_SAMPLE_RANDOM, spi->dev.driver->name, ts);
+ err = request_irq(spi->irq, ad7877_irq, IRQF_TRIGGER_FALLING,
+ spi->dev.driver->name, ts);
if (err) {
dev_dbg(&spi->dev, "irq %d busy?\n", spi->irq);
goto err_free_mem;
ad7879_setup(ts);
err = request_irq(bus->irq, ad7879_irq,
- IRQF_TRIGGER_FALLING | IRQF_SAMPLE_RANDOM,
- bus->dev.driver->name, ts);
+ IRQF_TRIGGER_FALLING, bus->dev.driver->name, ts);
if (err) {
dev_err(&bus->dev, "irq %d busy?\n", bus->irq);
void (*filter_cleanup)(void *data);
int (*get_pendown_state)(void);
int gpio_pendown;
+
+ void (*wait_for_sync)(void);
};
/* leave chip selected when we're done, for quicker re-select? */
return !gpio_get_value(ts->gpio_pendown);
}
+static void null_wait_for_sync(void)
+{
+}
+
/*
* PENIRQ only kicks the timer. The timer only reissues the SPI transfer,
* to retrieve touchscreen status.
default:
BUG();
}
+ ts->wait_for_sync();
status = spi_async(ts->spi, m);
if (status)
dev_err(&ts->spi->dev, "spi_async --> %d\n",
} else {
/* pen is still down, continue with the measurement */
ts->msg_idx = 0;
+ ts->wait_for_sync();
status = spi_async(ts->spi, &ts->msg[0]);
if (status)
dev_err(&ts->spi->dev, "spi_async --> %d\n", status);
* that here. (The "generic irq" framework may help...)
*/
ts->irq_disabled = 1;
- disable_irq(ts->spi->irq);
+ disable_irq_nosync(ts->spi->irq);
ts->pending = 1;
hrtimer_start(&ts->timer, ktime_set(0, TS_POLL_DELAY),
HRTIMER_MODE_REL);
ts->penirq_recheck_delay_usecs =
pdata->penirq_recheck_delay_usecs;
+ ts->wait_for_sync = pdata->wait_for_sync ? : null_wait_for_sync;
+
snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(&spi->dev));
input_dev->name = "ADS784x Touchscreen";
*
* Copyright (C) 2006-2008 Marvell International Ltd.
* Fengwei Yin <fengwei.yin@marvell.com>
+ * Bin Yang <bin.yang@marvell.com>
* Eric Miao <eric.miao@marvell.com>
*
* This program is free software; you can redistribute it and/or modify
goto err_reset;
touch->state = STATE_STOP;
+
+ /* FIXME: PEN_{UP/DOWN} events are expected to be
+ * available by stopping TSI, but this is found not
+ * always true, delay and simulate such an event
+ * here is more reliable
+ */
+ mdelay(1);
+ da9034_event_handler(touch,
+ is_pen_down(touch) ? EVENT_PEN_DOWN :
+ EVENT_PEN_UP);
break;
case STATE_STOP:
report_pen_up(touch);
touch->state = STATE_IDLE;
}
-
- input_sync(touch->input_dev);
break;
case STATE_WAIT:
if (is_pen_down(touch)) {
start_tsi(touch);
touch->state = STATE_BUSY;
- } else
+ } else {
+ report_pen_up(touch);
touch->state = STATE_IDLE;
+ }
break;
}
return;
struct da9034_touch *touch =
container_of(nb, struct da9034_touch, notifier);
- if (event & DA9034_EVENT_PEN_DOWN) {
- if (is_pen_down(touch))
- da9034_event_handler(touch, EVENT_PEN_DOWN);
- else
- da9034_event_handler(touch, EVENT_PEN_UP);
- }
-
if (event & DA9034_EVENT_TSI_READY)
da9034_event_handler(touch, EVENT_TSI_READY);
+ if ((event & DA9034_EVENT_PEN_DOWN) && touch->state == STATE_IDLE)
+ da9034_event_handler(touch, EVENT_PEN_DOWN);
+
return 0;
}
module_exit(da9034_touch_exit);
MODULE_DESCRIPTION("Touchscreen driver for Dialog Semiconductor DA9034");
-MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>");
+MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>, Bin Yang <bin.yang@marvell.com>");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:da9034-touch");
#else
static void wm97xx_acc_pen_up(struct wm97xx *wm)
{
- int count = 16;
+ unsigned int count;
+
schedule_timeout_uninterruptible(1);
- while (count < 16) {
+ for (count = 0; count < 16; count++)
MODR;
- count--;
- }
}
#endif
* provided. */
BUG_ON(!wm->mach_ops->irq_enable);
- if (request_irq(wm->pen_irq, wm97xx_pen_interrupt,
- IRQF_SHARED | IRQF_SAMPLE_RANDOM,
+ if (request_irq(wm->pen_irq, wm97xx_pen_interrupt, IRQF_SHARED,
"wm97xx-pen", wm)) {
dev_err(wm->dev,
"Failed to register pen down interrupt, polling");
if (ctrl_msg->dr.bRequest == USB_REQ_CLEAR_FEATURE) {
/* Special case handling for pipe reset */
le16_to_cpus(&ctrl_msg->dr.wIndex);
-
- /* toggle is reset on clear */
- usb_settoggle(adapter->usb_dev,
- ctrl_msg->dr.wIndex & ~USB_DIR_IN,
- (ctrl_msg->dr.wIndex & USB_DIR_IN) == 0,
- 0);
-
-
+ usb_reset_endpoint(adapter->usb_dev, ctrl_msg->dr.wIndex);
}
if (ctrl_msg->complete)
/* segments.c: */
void setup_default_gdt_entries(struct lguest_ro_state *state);
void setup_guest_gdt(struct lg_cpu *cpu);
-void load_guest_gdt(struct lg_cpu *cpu, unsigned long table, u32 num);
+void load_guest_gdt_entry(struct lg_cpu *cpu, unsigned int i,
+ u32 low, u32 hi);
void guest_load_tls(struct lg_cpu *cpu, unsigned long tls_array);
void copy_gdt(const struct lg_cpu *cpu, struct desc_struct *gdt);
void copy_gdt_tls(const struct lg_cpu *cpu, struct desc_struct *gdt);
gdt[i] = cpu->arch.gdt[i];
}
-/*H:620 This is where the Guest asks us to load a new GDT (LHCALL_LOAD_GDT).
- * We copy it from the Guest and tweak the entries. */
-void load_guest_gdt(struct lg_cpu *cpu, unsigned long table, u32 num)
+/*H:620 This is where the Guest asks us to load a new GDT entry
+ * (LHCALL_LOAD_GDT_ENTRY). We tweak the entry and copy it in. */
+void load_guest_gdt_entry(struct lg_cpu *cpu, u32 num, u32 lo, u32 hi)
{
/* We assume the Guest has the same number of GDT entries as the
* Host, otherwise we'd have to dynamically allocate the Guest GDT. */
if (num > ARRAY_SIZE(cpu->arch.gdt))
kill_guest(cpu, "too many gdt entries %i", num);
- /* We read the whole thing in, then fix it up. */
- __lgread(cpu, cpu->arch.gdt, table, num * sizeof(cpu->arch.gdt[0]));
- fixup_gdt_table(cpu, 0, ARRAY_SIZE(cpu->arch.gdt));
+ /* Set it up, then fix it. */
+ cpu->arch.gdt[num].a = lo;
+ cpu->arch.gdt[num].b = hi;
+ fixup_gdt_table(cpu, num, num+1);
/* Mark that the GDT changed so the core knows it has to copy it again,
* even if the Guest is run on the same CPU. */
cpu->changed |= CHANGED_GDT;
u8 insn[3] = {0xcd, 0x1f, 0x90};
__lgwrite(cpu, guest_pa(cpu, cpu->regs->eip), insn, sizeof(insn));
+ /* The above write might have caused a copy of that page to be made
+ * (if it was read-only). We need to make sure the Guest has
+ * up-to-date pagetables. As this doesn't happen often, we can just
+ * drop them all. */
+ guest_pagetable_clear_all(cpu);
}
static bool is_hypercall(struct lg_cpu *cpu)
int lguest_arch_do_hcall(struct lg_cpu *cpu, struct hcall_args *args)
{
switch (args->arg0) {
- case LHCALL_LOAD_GDT:
- load_guest_gdt(cpu, args->arg1, args->arg2);
+ case LHCALL_LOAD_GDT_ENTRY:
+ load_guest_gdt_entry(cpu, args->arg1, args->arg2, args->arg3);
break;
case LHCALL_LOAD_IDT_ENTRY:
load_guest_idt_entry(cpu, args->arg1, args->arg2, args->arg3);
+++ /dev/null
-/*
- * Copyright (C) 2004 Red Hat UK Ltd.
- *
- * This file is released under the GPL.
- */
-
-#ifndef DM_BIO_LIST_H
-#define DM_BIO_LIST_H
-
-#include <linux/bio.h>
-
-#ifdef CONFIG_BLOCK
-
-struct bio_list {
- struct bio *head;
- struct bio *tail;
-};
-
-static inline int bio_list_empty(const struct bio_list *bl)
-{
- return bl->head == NULL;
-}
-
-static inline void bio_list_init(struct bio_list *bl)
-{
- bl->head = bl->tail = NULL;
-}
-
-#define bio_list_for_each(bio, bl) \
- for (bio = (bl)->head; bio; bio = bio->bi_next)
-
-static inline unsigned bio_list_size(const struct bio_list *bl)
-{
- unsigned sz = 0;
- struct bio *bio;
-
- bio_list_for_each(bio, bl)
- sz++;
-
- return sz;
-}
-
-static inline void bio_list_add(struct bio_list *bl, struct bio *bio)
-{
- bio->bi_next = NULL;
-
- if (bl->tail)
- bl->tail->bi_next = bio;
- else
- bl->head = bio;
-
- bl->tail = bio;
-}
-
-static inline void bio_list_add_head(struct bio_list *bl, struct bio *bio)
-{
- bio->bi_next = bl->head;
-
- bl->head = bio;
-
- if (!bl->tail)
- bl->tail = bio;
-}
-
-static inline void bio_list_merge(struct bio_list *bl, struct bio_list *bl2)
-{
- if (!bl2->head)
- return;
-
- if (bl->tail)
- bl->tail->bi_next = bl2->head;
- else
- bl->head = bl2->head;
-
- bl->tail = bl2->tail;
-}
-
-static inline void bio_list_merge_head(struct bio_list *bl,
- struct bio_list *bl2)
-{
- if (!bl2->head)
- return;
-
- if (bl->head)
- bl2->tail->bi_next = bl->head;
- else
- bl->tail = bl2->tail;
-
- bl->head = bl2->head;
-}
-
-static inline struct bio *bio_list_pop(struct bio_list *bl)
-{
- struct bio *bio = bl->head;
-
- if (bio) {
- bl->head = bl->head->bi_next;
- if (!bl->head)
- bl->tail = NULL;
-
- bio->bi_next = NULL;
- }
-
- return bio;
-}
-
-static inline struct bio *bio_list_get(struct bio_list *bl)
-{
- struct bio *bio = bl->head;
-
- bl->head = bl->tail = NULL;
-
- return bio;
-}
-
-#endif /* CONFIG_BLOCK */
-#endif
#include <linux/device-mapper.h>
-#include "dm-bio-list.h"
-
#define DM_MSG_PREFIX "delay"
struct delay_c {
#include <linux/device-mapper.h>
#include "dm-path-selector.h"
-#include "dm-bio-list.h"
#include "dm-bio-record.h"
#include "dm-uevent.h"
* This file is released under the GPL.
*/
-#include "dm-bio-list.h"
#include "dm-bio-record.h"
#include <linux/init.h>
#include <linux/vmalloc.h>
#include "dm.h"
-#include "dm-bio-list.h"
#define DM_MSG_PREFIX "region hash"
#include <linux/workqueue.h>
#include "dm-exception-store.h"
-#include "dm-bio-list.h"
#define DM_MSG_PREFIX "snapshots"
*/
#include "dm.h"
-#include "dm-bio-list.h"
#include "dm-uevent.h"
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/seq_file.h>
#include "md.h"
-#include "dm-bio-list.h"
#include "raid1.h"
#include "bitmap.h"
#include <linux/blkdev.h>
#include <linux/seq_file.h>
#include "md.h"
-#include "dm-bio-list.h"
#include "raid10.h"
#include "bitmap.h"
return ret;
}
- usb_settoggle(hdw->usb_dev, 0 & 0xf, !(0 & USB_DIR_IN), 0);
usb_clear_halt(hdw->usb_dev, usb_sndbulkpipe(hdw->usb_dev, 0 & 0x7f));
pipe = usb_sndctrlpipe(hdw->usb_dev, 0);
.remove = __devexit_p(a2065_remove_one),
};
+static const struct net_device_ops lance_netdev_ops = {
+ .ndo_open = lance_open,
+ .ndo_stop = lance_close,
+ .ndo_start_xmit = lance_start_xmit,
+ .ndo_tx_timeout = lance_tx_timeout,
+ .ndo_set_multicast_list = lance_set_multicast,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __devinit a2065_init_one(struct zorro_dev *z,
const struct zorro_device_id *ent)
{
priv->rx_ring_mod_mask = RX_RING_MOD_MASK;
priv->tx_ring_mod_mask = TX_RING_MOD_MASK;
- dev->open = &lance_open;
- dev->stop = &lance_close;
- dev->hard_start_xmit = &lance_start_xmit;
- dev->tx_timeout = &lance_tx_timeout;
+ dev->netdev_ops = &lance_netdev_ops;
dev->watchdog_timeo = 5*HZ;
- dev->set_multicast_list = &lance_set_multicast;
dev->dma = 0;
init_timer(&priv->multicast_timer);
.remove = __devexit_p(ariadne_remove_one),
};
+static const struct net_device_ops ariadne_netdev_ops = {
+ .ndo_open = ariadne_open,
+ .ndo_stop = ariadne_close,
+ .ndo_start_xmit = ariadne_start_xmit,
+ .ndo_tx_timeout = ariadne_tx_timeout,
+ .ndo_get_stats = ariadne_get_stats,
+ .ndo_set_multicast_list = set_multicast_list,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __devinit ariadne_init_one(struct zorro_dev *z,
const struct zorro_device_id *ent)
{
dev->mem_start = ZTWO_VADDR(mem_start);
dev->mem_end = dev->mem_start+ARIADNE_RAM_SIZE;
- dev->open = &ariadne_open;
- dev->stop = &ariadne_close;
- dev->hard_start_xmit = &ariadne_start_xmit;
- dev->tx_timeout = &ariadne_tx_timeout;
+ dev->netdev_ops = &ariadne_netdev_ops;
dev->watchdog_timeo = 5*HZ;
- dev->get_stats = &ariadne_get_stats;
- dev->set_multicast_list = &set_multicast_list;
err = register_netdev(dev);
if (err) {
if (net_debug && version_printed++ == 0)
printk(KERN_INFO "%s", version);
}
+static const struct net_device_ops am79c961_netdev_ops = {
+ .ndo_open = am79c961_open,
+ .ndo_stop = am79c961_close,
+ .ndo_start_xmit = am79c961_sendpacket,
+ .ndo_get_stats = am79c961_getstats,
+ .ndo_set_multicast_list = am79c961_setmulticastlist,
+ .ndo_tx_timeout = am79c961_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = am79c961_poll_controller,
+#endif
+};
static int __init am79c961_probe(struct platform_device *pdev)
{
if (am79c961_hw_init(dev))
goto release;
- dev->open = am79c961_open;
- dev->stop = am79c961_close;
- dev->hard_start_xmit = am79c961_sendpacket;
- dev->get_stats = am79c961_getstats;
- dev->set_multicast_list = am79c961_setmulticastlist;
- dev->tx_timeout = am79c961_timeout;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = am79c961_poll_controller;
-#endif
+ dev->netdev_ops = &am79c961_netdev_ops;
ret = register_netdev(dev);
if (ret == 0) {
/*
* Enable/Disable promiscuous and multicast modes.
*/
-static void at91ether_set_rx_mode(struct net_device *dev)
+static void at91ether_set_multicast_list(struct net_device *dev)
{
unsigned long cfg;
/*
* Transmit packet.
*/
-static int at91ether_tx(struct sk_buff *skb, struct net_device *dev)
+static int at91ether_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct at91_private *lp = netdev_priv(dev);
dev->trans_start = jiffies;
} else {
- printk(KERN_ERR "at91_ether.c: at91ether_tx() called, but device is busy!\n");
+ printk(KERN_ERR "at91_ether.c: at91ether_start_xmit() called, but device is busy!\n");
return 1; /* if we return anything but zero, dev.c:1055 calls kfree_skb(skb)
on this skb, he also reports -ENETDOWN and printk's, so either
we free and return(0) or don't free and return 1 */
}
#endif
+static const struct net_device_ops at91ether_netdev_ops = {
+ .ndo_open = at91ether_open,
+ .ndo_stop = at91ether_close,
+ .ndo_start_xmit = at91ether_start_xmit,
+ .ndo_get_stats = at91ether_stats,
+ .ndo_set_multicast_list = at91ether_set_multicast_list,
+ .ndo_set_mac_address = set_mac_address,
+ .ndo_do_ioctl = at91ether_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = at91ether_poll_controller,
+#endif
+};
+
/*
* Initialize the ethernet interface
*/
spin_lock_init(&lp->lock);
ether_setup(dev);
- dev->open = at91ether_open;
- dev->stop = at91ether_close;
- dev->hard_start_xmit = at91ether_tx;
- dev->get_stats = at91ether_stats;
- dev->set_multicast_list = at91ether_set_rx_mode;
- dev->set_mac_address = set_mac_address;
+ dev->netdev_ops = &at91ether_netdev_ops;
dev->ethtool_ops = &at91ether_ethtool_ops;
- dev->do_ioctl = at91ether_ioctl;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = at91ether_poll_controller;
-#endif
SET_NETDEV_DEV(dev, &pdev->dev);
struct ep93xx_priv
{
struct resource *res;
- void *base_addr;
+ void __iomem *base_addr;
int irq;
struct ep93xx_descs *descs;
.get_link = ep93xx_get_link,
};
-struct net_device *ep93xx_dev_alloc(struct ep93xx_eth_data *data)
+static const struct net_device_ops ep93xx_netdev_ops = {
+ .ndo_open = ep93xx_open,
+ .ndo_stop = ep93xx_close,
+ .ndo_start_xmit = ep93xx_xmit,
+ .ndo_get_stats = ep93xx_get_stats,
+ .ndo_do_ioctl = ep93xx_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
+static struct net_device *ep93xx_dev_alloc(struct ep93xx_eth_data *data)
{
struct net_device *dev;
memcpy(dev->dev_addr, data->dev_addr, ETH_ALEN);
- dev->get_stats = ep93xx_get_stats;
dev->ethtool_ops = &ep93xx_ethtool_ops;
- dev->hard_start_xmit = ep93xx_xmit;
- dev->open = ep93xx_open;
- dev->stop = ep93xx_close;
- dev->do_ioctl = ep93xx_ioctl;
+ dev->netdev_ops = &ep93xx_netdev_ops;
dev->features |= NETIF_F_SG | NETIF_F_HW_CSUM;
printk(KERN_INFO "%s", version);
}
+static const struct net_device_ops ether1_netdev_ops = {
+ .ndo_open = ether1_open,
+ .ndo_stop = ether1_close,
+ .ndo_start_xmit = ether1_sendpacket,
+ .ndo_get_stats = ether1_getstats,
+ .ndo_set_multicast_list = ether1_setmulticastlist,
+ .ndo_tx_timeout = ether1_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __devinit
ether1_probe(struct expansion_card *ec, const struct ecard_id *id)
{
goto free;
}
- dev->open = ether1_open;
- dev->stop = ether1_close;
- dev->hard_start_xmit = ether1_sendpacket;
- dev->get_stats = ether1_getstats;
- dev->set_multicast_list = ether1_setmulticastlist;
- dev->tx_timeout = ether1_timeout;
+ dev->netdev_ops = ðer1_netdev_ops;
dev->watchdog_timeo = 5 * HZ / 100;
ret = register_netdev(dev);
printk(KERN_INFO "%s", version);
}
+static const struct net_device_ops ether3_netdev_ops = {
+ .ndo_open = ether3_open,
+ .ndo_stop = ether3_close,
+ .ndo_start_xmit = ether3_sendpacket,
+ .ndo_get_stats = ether3_getstats,
+ .ndo_set_multicast_list = ether3_setmulticastlist,
+ .ndo_tx_timeout = ether3_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __devinit
ether3_probe(struct expansion_card *ec, const struct ecard_id *id)
{
goto free;
}
- dev->open = ether3_open;
- dev->stop = ether3_close;
- dev->hard_start_xmit = ether3_sendpacket;
- dev->get_stats = ether3_getstats;
- dev->set_multicast_list = ether3_setmulticastlist;
- dev->tx_timeout = ether3_timeout;
+ dev->netdev_ops = ðer3_netdev_ops;
dev->watchdog_timeo = 5 * HZ / 100;
ret = register_netdev(dev);
return( ret );
}
+static const struct net_device_ops lance_netdev_ops = {
+ .ndo_open = lance_open,
+ .ndo_stop = lance_close,
+ .ndo_start_xmit = lance_start_xmit,
+ .ndo_set_multicast_list = set_multicast_list,
+ .ndo_set_mac_address = lance_set_mac_address,
+ .ndo_tx_timeout = lance_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
static unsigned long __init lance_probe1( struct net_device *dev,
struct lance_addr *init_rec )
if (did_version++ == 0)
DPRINTK( 1, ( version ));
- /* The LANCE-specific entries in the device structure. */
- dev->open = &lance_open;
- dev->hard_start_xmit = &lance_start_xmit;
- dev->stop = &lance_close;
- dev->set_multicast_list = &set_multicast_list;
- dev->set_mac_address = &lance_set_mac_address;
+ dev->netdev_ops = &lance_netdev_ops;
/* XXX MSch */
- dev->tx_timeout = lance_tx_timeout;
dev->watchdog_timeo = TX_TIMEOUT;
return( 1 );
netif_wake_queue(dev);
}
-static void set_rx_mode(struct net_device *dev)
+static void au1000_multicast_list(struct net_device *dev)
{
struct au1000_private *aup = netdev_priv(dev);
if (au1000_debug > 4)
- printk("%s: set_rx_mode: flags=%x\n", dev->name, dev->flags);
+ printk("%s: au1000_multicast_list: flags=%x\n", dev->name, dev->flags);
if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
aup->mac->control |= MAC_PROMISCUOUS;
return phy_mii_ioctl(aup->phy_dev, if_mii(rq), cmd);
}
+static const struct net_device_ops au1000_netdev_ops = {
+ .ndo_open = au1000_open,
+ .ndo_stop = au1000_close,
+ .ndo_start_xmit = au1000_tx,
+ .ndo_set_multicast_list = au1000_multicast_list,
+ .ndo_do_ioctl = au1000_ioctl,
+ .ndo_tx_timeout = au1000_tx_timeout,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
static struct net_device * au1000_probe(int port_num)
{
static unsigned version_printed = 0;
dev->base_addr = base;
dev->irq = irq;
- dev->open = au1000_open;
- dev->hard_start_xmit = au1000_tx;
- dev->stop = au1000_close;
- dev->set_multicast_list = &set_rx_mode;
- dev->do_ioctl = &au1000_ioctl;
+ dev->netdev_ops = &au1000_netdev_ops;
SET_ETHTOOL_OPS(dev, &au1000_ethtool_ops);
- dev->tx_timeout = au1000_tx_timeout;
dev->watchdog_timeo = ETH_TX_TIMEOUT;
/*
be_cmd_get_flow_control(&adapter->ctrl, &ecmd->tx_pause,
&ecmd->rx_pause);
- ecmd->autoneg = AUTONEG_ENABLE;
+ ecmd->autoneg = 0;
}
static int
struct be_adapter *adapter = netdev_priv(netdev);
int status;
- if (ecmd->autoneg != AUTONEG_ENABLE)
+ if (ecmd->autoneg != 0)
return -EINVAL;
status = be_cmd_set_flow_control(&adapter->ctrl, ecmd->tx_pause,
return 0;
}
+static const struct net_device_ops bfin_mac_netdev_ops = {
+ .ndo_open = bfin_mac_open,
+ .ndo_stop = bfin_mac_close,
+ .ndo_start_xmit = bfin_mac_hard_start_xmit,
+ .ndo_set_mac_address = bfin_mac_set_mac_address,
+ .ndo_tx_timeout = bfin_mac_timeout,
+ .ndo_set_multicast_list = bfin_mac_set_multicast_list,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = bfin_mac_poll,
+#endif
+};
+
/*
*
* this makes the board clean up everything that it can
/* Fill in the fields of the device structure with ethernet values. */
ether_setup(ndev);
- ndev->open = bfin_mac_open;
- ndev->stop = bfin_mac_close;
- ndev->hard_start_xmit = bfin_mac_hard_start_xmit;
- ndev->set_mac_address = bfin_mac_set_mac_address;
- ndev->tx_timeout = bfin_mac_timeout;
- ndev->set_multicast_list = bfin_mac_set_multicast_list;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- ndev->poll_controller = bfin_mac_poll;
-#endif
+ ndev->netdev_ops = &bfin_mac_netdev_ops;
ndev->ethtool_ops = &bfin_mac_ethtool_ops;
spin_lock_init(&lp->lock);
if (arp->op_code == htons(ARPOP_REPLY)) {
/* update rx hash table for this ARP */
- printk("rar: update orig %s bond_dev %s\n", orig_dev->name,
- bond_dev->name);
bond = netdev_priv(bond_dev);
rlb_update_entry_from_arp(bond, arp);
pr_debug("Server received an ARP Reply from client\n");
for (i = 0; (i < BOND_MAX_ARP_TARGETS); i++) {
if (!targets[i])
- continue;
+ break;
pr_debug("basa: target %x\n", targets[i]);
if (list_empty(&bond->vlan_list)) {
pr_debug("basa: empty vlan: arp_send\n");
int i;
__be32 *targets = bond->params.arp_targets;
- targets = bond->params.arp_targets;
for (i = 0; (i < BOND_MAX_ARP_TARGETS) && targets[i]; i++) {
pr_debug("bva: sip %pI4 tip %pI4 t[%d] %pI4 bhti(tip) %d\n",
&sip, &tip, i, &targets[i], bond_has_this_ip(bond, tip));
for(i = 0; (i < BOND_MAX_ARP_TARGETS) ;i++) {
if (!bond->params.arp_targets[i])
- continue;
+ break;
if (printed)
seq_printf(seq, ",");
seq_printf(seq, " %pI4", &bond->params.arp_targets[i]);
goto out;
}
/* look for an empty slot to put the target in, and check for dupes */
- for (i = 0; (i < BOND_MAX_ARP_TARGETS); i++) {
+ for (i = 0; (i < BOND_MAX_ARP_TARGETS) && !done; i++) {
if (targets[i] == newtarget) { /* duplicate */
printk(KERN_ERR DRV_NAME
": %s: ARP target %pI4 is already present\n",
bond->dev->name, &newtarget);
- if (done)
- targets[i] = 0;
ret = -EINVAL;
goto out;
}
- if (targets[i] == 0 && !done) {
+ if (targets[i] == 0) {
printk(KERN_INFO DRV_NAME
": %s: adding ARP target %pI4.\n",
bond->dev->name, &newtarget);
goto out;
}
- for (i = 0; (i < BOND_MAX_ARP_TARGETS); i++) {
+ for (i = 0; (i < BOND_MAX_ARP_TARGETS) && !done; i++) {
if (targets[i] == newtarget) {
+ int j;
printk(KERN_INFO DRV_NAME
": %s: removing ARP target %pI4.\n",
bond->dev->name, &newtarget);
- targets[i] = 0;
+ for (j = i; (j < (BOND_MAX_ARP_TARGETS-1)) && targets[j+1]; j++)
+ targets[j] = targets[j+1];
+
+ targets[j] = 0;
done = 1;
}
}
struct transceiver_ops* transceiver = &transceivers[0];
+static const struct net_device_ops e100_netdev_ops = {
+ .ndo_open = e100_open,
+ .ndo_stop = e100_close,
+ .ndo_start_xmit = e100_send_packet,
+ .ndo_tx_timeout = e100_tx_timeout,
+ .ndo_get_stats = e100_get_stats,
+ .ndo_set_multicast_list = set_multicast_list,
+ .ndo_do_ioctl = e100_ioctl,
+ .ndo_set_mac_address = e100_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_config = e100_set_config,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = e100_netpoll,
+#endif
+};
+
#define tx_done(dev) (*R_DMA_CH0_CMD == 0)
/*
/* fill in our handlers so the network layer can talk to us in the future */
- dev->open = e100_open;
- dev->hard_start_xmit = e100_send_packet;
- dev->stop = e100_close;
- dev->get_stats = e100_get_stats;
- dev->set_multicast_list = set_multicast_list;
- dev->set_mac_address = e100_set_mac_address;
dev->ethtool_ops = &e100_ethtool_ops;
- dev->do_ioctl = e100_ioctl;
- dev->set_config = e100_set_config;
- dev->tx_timeout = e100_tx_timeout;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = e100_netpoll;
-#endif
+ dev->netdev_ops = &e100_netdev_ops;
spin_lock_init(&np->lock);
spin_lock_init(&np->led_lock);
lance_set_multicast(dev);
}
+static const struct net_device_ops lance_netdev_ops = {
+ .ndo_open = lance_open,
+ .ndo_stop = lance_close,
+ .ndo_start_xmit = lance_start_xmit,
+ .ndo_tx_timeout = lance_tx_timeout,
+ .ndo_set_multicast_list = lance_set_multicast,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __init dec_lance_probe(struct device *bdev, const int type)
{
static unsigned version_printed;
printk(", addr = %pM, irq = %d\n", dev->dev_addr, dev->irq);
- dev->open = &lance_open;
- dev->stop = &lance_close;
- dev->hard_start_xmit = &lance_start_xmit;
- dev->tx_timeout = &lance_tx_timeout;
+ dev->netdev_ops = &lance_netdev_ops;
dev->watchdog_timeo = 5*HZ;
- dev->set_multicast_list = &lance_set_multicast;
/* lp->ll is the location of the registers for lance card */
lp->ll = ll;
static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid);
static void e1000_restore_vlan(struct e1000_adapter *adapter);
-static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
static int e1000_resume(struct pci_dev *pdev);
#endif
static void e1000_shutdown(struct pci_dev *pdev);
struct e1000_buffer *buffer_info;
unsigned int i, eop;
unsigned int count = 0;
- bool cleaned;
+ bool cleaned = false;
unsigned int total_tx_bytes=0, total_tx_packets=0;
i = tx_ring->next_to_clean;
return 0;
}
-static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
+static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct e1000_adapter *adapter = netdev_priv(netdev);
ew32(WUC, E1000_WUC_PME_EN);
ew32(WUFC, wufc);
- pci_enable_wake(pdev, PCI_D3hot, 1);
- pci_enable_wake(pdev, PCI_D3cold, 1);
} else {
ew32(WUC, 0);
ew32(WUFC, 0);
- pci_enable_wake(pdev, PCI_D3hot, 0);
- pci_enable_wake(pdev, PCI_D3cold, 0);
}
e1000_release_manageability(adapter);
+ *enable_wake = !!wufc;
+
/* make sure adapter isn't asleep if manageability is enabled */
- if (adapter->en_mng_pt) {
- pci_enable_wake(pdev, PCI_D3hot, 1);
- pci_enable_wake(pdev, PCI_D3cold, 1);
- }
+ if (adapter->en_mng_pt)
+ *enable_wake = true;
if (hw->phy_type == e1000_phy_igp_3)
e1000_phy_powerdown_workaround(hw);
pci_disable_device(pdev);
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
-
return 0;
}
#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ int retval;
+ bool wake;
+
+ retval = __e1000_shutdown(pdev, &wake);
+ if (retval)
+ return retval;
+
+ if (wake) {
+ pci_prepare_to_sleep(pdev);
+ } else {
+ pci_wake_from_d3(pdev, false);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
+
+ return 0;
+}
+
static int e1000_resume(struct pci_dev *pdev)
{
struct net_device *netdev = pci_get_drvdata(pdev);
static void e1000_shutdown(struct pci_dev *pdev)
{
- e1000_suspend(pdev, PMSG_SUSPEND);
+ bool wake;
+
+ __e1000_shutdown(pdev, &wake);
+
+ if (system_state == SYSTEM_POWER_OFF) {
+ pci_wake_from_d3(pdev, wake);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
}
#ifdef CONFIG_NET_POLL_CONTROLLER
struct e1000_buffer *buffer_info;
unsigned int i, eop;
unsigned int count = 0;
- bool cleaned;
+ bool cleaned = false;
unsigned int total_tx_bytes = 0, total_tx_packets = 0;
i = tx_ring->next_to_clean;
}
}
-static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
+static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct e1000_adapter *adapter = netdev_priv(netdev);
ew32(WUC, E1000_WUC_PME_EN);
ew32(WUFC, wufc);
- pci_enable_wake(pdev, PCI_D3hot, 1);
- pci_enable_wake(pdev, PCI_D3cold, 1);
} else {
ew32(WUC, 0);
ew32(WUFC, 0);
- pci_enable_wake(pdev, PCI_D3hot, 0);
- pci_enable_wake(pdev, PCI_D3cold, 0);
}
+ *enable_wake = !!wufc;
+
/* make sure adapter isn't asleep if manageability is enabled */
- if (adapter->flags & FLAG_MNG_PT_ENABLED) {
- pci_enable_wake(pdev, PCI_D3hot, 1);
- pci_enable_wake(pdev, PCI_D3cold, 1);
- }
+ if (adapter->flags & FLAG_MNG_PT_ENABLED)
+ *enable_wake = true;
if (adapter->hw.phy.type == e1000_phy_igp_3)
e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
pci_disable_device(pdev);
+ return 0;
+}
+
+static void e1000_power_off(struct pci_dev *pdev, bool sleep, bool wake)
+{
+ if (sleep && wake) {
+ pci_prepare_to_sleep(pdev);
+ return;
+ }
+
+ pci_wake_from_d3(pdev, wake);
+ pci_set_power_state(pdev, PCI_D3hot);
+}
+
+static void e1000_complete_shutdown(struct pci_dev *pdev, bool sleep,
+ bool wake)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
/*
* The pci-e switch on some quad port adapters will report a
* correctable error when the MAC transitions from D0 to D3. To
pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL,
(devctl & ~PCI_EXP_DEVCTL_CERE));
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ e1000_power_off(pdev, sleep, wake);
pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL, devctl);
} else {
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ e1000_power_off(pdev, sleep, wake);
}
-
- return 0;
}
static void e1000e_disable_l1aspm(struct pci_dev *pdev)
}
#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ int retval;
+ bool wake;
+
+ retval = __e1000_shutdown(pdev, &wake);
+ if (!retval)
+ e1000_complete_shutdown(pdev, true, wake);
+
+ return retval;
+}
+
static int e1000_resume(struct pci_dev *pdev)
{
struct net_device *netdev = pci_get_drvdata(pdev);
static void e1000_shutdown(struct pci_dev *pdev)
{
- e1000_suspend(pdev, PMSG_SUSPEND);
+ bool wake = false;
+
+ __e1000_shutdown(pdev, &wake);
+
+ if (system_state == SYSTEM_POWER_OFF)
+ e1000_complete_shutdown(pdev, false, wake);
}
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_change_mtu = ehea_change_mtu,
.ndo_vlan_rx_register = ehea_vlan_rx_register,
.ndo_vlan_rx_add_vid = ehea_vlan_rx_add_vid,
- .ndo_vlan_rx_kill_vid = ehea_vlan_rx_kill_vid
+ .ndo_vlan_rx_kill_vid = ehea_vlan_rx_kill_vid,
+ .ndo_tx_timeout = ehea_tx_watchdog,
};
struct ehea_port *ehea_setup_single_port(struct ehea_adapter *adapter,
| NETIF_F_HIGHDMA | NETIF_F_IP_CSUM | NETIF_F_HW_VLAN_TX
| NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER
| NETIF_F_LLTX;
- dev->tx_timeout = &ehea_tx_watchdog;
dev->watchdog_timeo = EHEA_WATCH_DOG_TIMEOUT;
INIT_WORK(&port->reset_task, ehea_reset_port);
mod_timer(&np->nic_poll, jiffies + POLL_WAIT);
}
spin_unlock_irqrestore(&np->lock, flags);
- __napi_complete(napi);
+ napi_complete(napi);
return rx_work;
}
if (rx_work < budget) {
/* re-enable interrupts
(msix not enabled in napi) */
- __napi_complete(napi);
+ napi_complete(napi);
writel(np->irqmask, base + NvRegIrqMask);
}
#define IS_FEC(match) 0
#endif
+static const struct net_device_ops fs_enet_netdev_ops = {
+ .ndo_open = fs_enet_open,
+ .ndo_stop = fs_enet_close,
+ .ndo_get_stats = fs_enet_get_stats,
+ .ndo_start_xmit = fs_enet_start_xmit,
+ .ndo_tx_timeout = fs_timeout,
+ .ndo_set_multicast_list = fs_set_multicast_list,
+ .ndo_do_ioctl = fs_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = fs_enet_netpoll,
+#endif
+};
+
static int __devinit fs_enet_probe(struct of_device *ofdev,
const struct of_device_id *match)
{
fep->tx_ring = fpi->tx_ring;
fep->rx_ring = fpi->rx_ring;
- ndev->open = fs_enet_open;
- ndev->hard_start_xmit = fs_enet_start_xmit;
- ndev->tx_timeout = fs_timeout;
+ ndev->netdev_ops = &fs_enet_netdev_ops;
ndev->watchdog_timeo = 2 * HZ;
- ndev->stop = fs_enet_close;
- ndev->get_stats = fs_enet_get_stats;
- ndev->set_multicast_list = fs_set_multicast_list;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- ndev->poll_controller = fs_enet_netpoll;
-#endif
if (fpi->use_napi)
netif_napi_add(ndev, &fep->napi, fs_enet_rx_napi,
fpi->napi_weight);
ndev->ethtool_ops = &fs_ethtool_ops;
- ndev->do_ioctl = fs_ioctl;
init_timer(&fep->phy_timer_list);
struct net_device *dev = priv->ndev;
if (dev->flags & IFF_UP) {
+ netif_stop_queue(dev);
stop_gfar(dev);
startup_gfar(dev);
+ netif_start_queue(dev);
}
netif_tx_schedule_all(dev);
return 0;
}
+static const struct net_device_ops emac_netdev_ops = {
+ .ndo_open = emac_open,
+ .ndo_stop = emac_close,
+ .ndo_get_stats = emac_stats,
+ .ndo_set_multicast_list = emac_set_multicast_list,
+ .ndo_do_ioctl = emac_ioctl,
+ .ndo_tx_timeout = emac_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_start_xmit = emac_start_xmit,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
+static const struct net_device_ops emac_gige_netdev_ops = {
+ .ndo_open = emac_open,
+ .ndo_stop = emac_close,
+ .ndo_get_stats = emac_stats,
+ .ndo_set_multicast_list = emac_set_multicast_list,
+ .ndo_do_ioctl = emac_ioctl,
+ .ndo_tx_timeout = emac_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_start_xmit = emac_start_xmit_sg,
+ .ndo_change_mtu = emac_change_mtu,
+};
+
static int __devinit emac_probe(struct of_device *ofdev,
const struct of_device_id *match)
{
if (err != 0)
goto err_detach_tah;
- /* Fill in the driver function table */
- ndev->open = &emac_open;
if (dev->tah_dev)
ndev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
- ndev->tx_timeout = &emac_tx_timeout;
ndev->watchdog_timeo = 5 * HZ;
- ndev->stop = &emac_close;
- ndev->get_stats = &emac_stats;
- ndev->set_multicast_list = &emac_set_multicast_list;
- ndev->do_ioctl = &emac_ioctl;
if (emac_phy_supports_gige(dev->phy_mode)) {
- ndev->hard_start_xmit = &emac_start_xmit_sg;
- ndev->change_mtu = &emac_change_mtu;
+ ndev->netdev_ops = &emac_gige_netdev_ops;
dev->commac.ops = &emac_commac_sg_ops;
- } else {
- ndev->hard_start_xmit = &emac_start_xmit;
- }
+ } else
+ ndev->netdev_ops = &emac_netdev_ops;
SET_ETHTOOL_OPS(ndev, &emac_ethtool_ops);
netif_carrier_off(ndev);
* Writes value at the given offset in the register array which stores
* the VLAN filter table.
**/
-void igb_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
+static void igb_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
{
array_wr32(E1000_VFTA, offset, value);
wrfl();
s32 igb_check_alt_mac_addr(struct e1000_hw *hw);
void igb_reset_adaptive(struct e1000_hw *hw);
void igb_update_adaptive(struct e1000_hw *hw);
-void igb_write_vfta(struct e1000_hw *hw, u32 offset, u32 value);
bool igb_enable_mng_pass_thru(struct e1000_hw *hw);
* returns SUCCESS if it successfully received a message notification and
* copied it into the receive buffer.
**/
-s32 igb_read_posted_mbx(struct e1000_hw *hw, u32 *msg, u16 size, u16 mbx_id)
+static s32 igb_read_posted_mbx(struct e1000_hw *hw, u32 *msg, u16 size, u16 mbx_id)
{
struct e1000_mbx_info *mbx = &hw->mbx;
s32 ret_val = -E1000_ERR_MBX;
* returns SUCCESS if it successfully copied message into the buffer and
* received an ack to that message within delay * timeout period
**/
-s32 igb_write_posted_mbx(struct e1000_hw *hw, u32 *msg, u16 size, u16 mbx_id)
+static s32 igb_write_posted_mbx(struct e1000_hw *hw, u32 *msg, u16 size, u16 mbx_id)
{
struct e1000_mbx_info *mbx = &hw->mbx;
s32 ret_val = 0;
return ret_val;
}
-/**
- * e1000_init_mbx_ops_generic - Initialize NVM function pointers
- * @hw: pointer to the HW structure
- *
- * Setups up the function pointers to no-op functions
- **/
-void e1000_init_mbx_ops_generic(struct e1000_hw *hw)
-{
- struct e1000_mbx_info *mbx = &hw->mbx;
- mbx->ops.read_posted = igb_read_posted_mbx;
- mbx->ops.write_posted = igb_write_posted_mbx;
-}
-
static s32 igb_check_for_bit_pf(struct e1000_hw *hw, u32 mask)
{
u32 mbvficr = rd32(E1000_MBVFICR);
s32 igb_read_mbx(struct e1000_hw *, u32 *, u16, u16);
s32 igb_write_mbx(struct e1000_hw *, u32 *, u16, u16);
-s32 igb_read_posted_mbx(struct e1000_hw *, u32 *, u16, u16);
-s32 igb_write_posted_mbx(struct e1000_hw *, u32 *, u16, u16);
s32 igb_check_for_msg(struct e1000_hw *, u16);
s32 igb_check_for_ack(struct e1000_hw *, u16);
s32 igb_check_for_rst(struct e1000_hw *, u16);
int i;
unsigned char mac_addr[ETH_ALEN];
- if (num_vfs)
+ if (num_vfs) {
adapter->vf_data = kcalloc(num_vfs,
sizeof(struct vf_data_storage),
GFP_KERNEL);
- if (!adapter->vf_data) {
- dev_err(&pdev->dev, "Could not allocate VF private "
- "data - IOV enable failed\n");
- } else {
- err = pci_enable_sriov(pdev, num_vfs);
- if (!err) {
- adapter->vfs_allocated_count = num_vfs;
- dev_info(&pdev->dev, "%d vfs allocated\n", num_vfs);
- for (i = 0; i < adapter->vfs_allocated_count; i++) {
- random_ether_addr(mac_addr);
- igb_set_vf_mac(adapter, i, mac_addr);
- }
+ if (!adapter->vf_data) {
+ dev_err(&pdev->dev,
+ "Could not allocate VF private data - "
+ "IOV enable failed\n");
} else {
- kfree(adapter->vf_data);
- adapter->vf_data = NULL;
+ err = pci_enable_sriov(pdev, num_vfs);
+ if (!err) {
+ adapter->vfs_allocated_count = num_vfs;
+ dev_info(&pdev->dev,
+ "%d vfs allocated\n",
+ num_vfs);
+ for (i = 0;
+ i < adapter->vfs_allocated_count;
+ i++) {
+ random_ether_addr(mac_addr);
+ igb_set_vf_mac(adapter, i,
+ mac_addr);
+ }
+ } else {
+ kfree(adapter->vf_data);
+ adapter->vf_data = NULL;
+ }
}
}
}
extern int igbvf_up(struct igbvf_adapter *);
extern void igbvf_down(struct igbvf_adapter *);
extern void igbvf_reinit_locked(struct igbvf_adapter *);
-extern void igbvf_reset(struct igbvf_adapter *);
extern int igbvf_setup_rx_resources(struct igbvf_adapter *, struct igbvf_ring *);
extern int igbvf_setup_tx_resources(struct igbvf_adapter *, struct igbvf_ring *);
extern void igbvf_free_rx_resources(struct igbvf_ring *);
extern void igbvf_free_tx_resources(struct igbvf_ring *);
extern void igbvf_update_stats(struct igbvf_adapter *);
-extern void igbvf_set_interrupt_capability(struct igbvf_adapter *);
-extern void igbvf_reset_interrupt_capability(struct igbvf_adapter *);
extern unsigned int copybreak;
static const char igbvf_copyright[] = "Copyright (c) 2009 Intel Corporation.";
static int igbvf_poll(struct napi_struct *napi, int budget);
+static void igbvf_reset(struct igbvf_adapter *);
+static void igbvf_set_interrupt_capability(struct igbvf_adapter *);
+static void igbvf_reset_interrupt_capability(struct igbvf_adapter *);
static struct igbvf_info igbvf_vf_info = {
.mac = e1000_vfadapt,
e1e_flush();
}
-void igbvf_reset_interrupt_capability(struct igbvf_adapter *adapter)
+static void igbvf_reset_interrupt_capability(struct igbvf_adapter *adapter)
{
if (adapter->msix_entries) {
pci_disable_msix(adapter->pdev);
* Attempt to configure interrupts using the best available
* capabilities of the hardware and kernel.
**/
-void igbvf_set_interrupt_capability(struct igbvf_adapter *adapter)
+static void igbvf_set_interrupt_capability(struct igbvf_adapter *adapter)
{
int err = -ENOMEM;
int i;
* set/changed during runtime. After reset the device needs to be
* properly configured for Rx, Tx etc.
*/
-void igbvf_reset(struct igbvf_adapter *adapter)
+static void igbvf_reset(struct igbvf_adapter *adapter)
{
struct e1000_mac_info *mac = &adapter->hw.mac;
struct net_device *netdev = adapter->netdev;
* e1000_init_mac_params_vf - Inits MAC params
* @hw: pointer to the HW structure
**/
-s32 e1000_init_mac_params_vf(struct e1000_hw *hw)
+static s32 e1000_init_mac_params_vf(struct e1000_hw *hw)
{
struct e1000_mac_info *mac = &hw->mac;
/* These functions must be implemented by drivers */
void e1000_rlpml_set_vf(struct e1000_hw *, u16);
void e1000_init_function_pointers_vf(struct e1000_hw *hw);
-s32 e1000_init_mac_params_vf(struct e1000_hw *hw);
#endif /* _E1000_VF_H_ */
}
#endif
+static const struct net_device_ops ioc3_netdev_ops = {
+ .ndo_open = ioc3_open,
+ .ndo_stop = ioc3_close,
+ .ndo_start_xmit = ioc3_start_xmit,
+ .ndo_tx_timeout = ioc3_timeout,
+ .ndo_get_stats = ioc3_get_stats,
+ .ndo_set_multicast_list = ioc3_set_multicast_list,
+ .ndo_do_ioctl = ioc3_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = ioc3_set_mac_address,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
static int __devinit ioc3_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
ioc3_get_eaddr(ip);
/* The IOC3-specific entries in the device structure. */
- dev->open = ioc3_open;
- dev->hard_start_xmit = ioc3_start_xmit;
- dev->tx_timeout = ioc3_timeout;
dev->watchdog_timeo = 5 * HZ;
- dev->stop = ioc3_close;
- dev->get_stats = ioc3_get_stats;
- dev->do_ioctl = ioc3_ioctl;
- dev->set_multicast_list = ioc3_set_multicast_list;
- dev->set_mac_address = ioc3_set_mac_address;
+ dev->netdev_ops = &ioc3_netdev_ops;
dev->ethtool_ops = &ioc3_ethtool_ops;
dev->features = NETIF_F_IP_CSUM;
}
#endif
+static const struct net_device_ops netcard_netdev_ops = {
+ .ndo_open = net_open,
+ .ndo_stop = net_close,
+ .ndo_start_xmit = net_send_packet,
+ .ndo_get_stats = net_get_stats,
+ .ndo_set_multicast_list = set_multicast_list,
+ .ndo_tx_timeout = net_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
/*
* This is the real probe routine. Linux has a history of friendly device
* probes on the ISA bus. A good device probes avoids doing writes, and
np = netdev_priv(dev);
spin_lock_init(&np->lock);
- dev->open = net_open;
- dev->stop = net_close;
- dev->hard_start_xmit = net_send_packet;
- dev->get_stats = net_get_stats;
- dev->set_multicast_list = &set_multicast_list;
-
- dev->tx_timeout = &net_tx_timeout;
+ dev->netdev_ops = &netcard_netdev_ops;
dev->watchdog_timeo = MY_TX_TIMEOUT;
err = register_netdev(dev);
}
/**
- * ixgbe_blink_led_start_82598 - Blink LED based on index.
- * @hw: pointer to hardware structure
- * @index: led number to blink
- **/
-static s32 ixgbe_blink_led_start_82598(struct ixgbe_hw *hw, u32 index)
-{
- ixgbe_link_speed speed = 0;
- bool link_up = 0;
- u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
-
- /*
- * Link must be up to auto-blink the LEDs on the 82598EB MAC;
- * force it if link is down.
- */
- hw->mac.ops.check_link(hw, &speed, &link_up, false);
-
- if (!link_up) {
- autoc_reg |= IXGBE_AUTOC_FLU;
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
- msleep(10);
- }
-
- led_reg &= ~IXGBE_LED_MODE_MASK(index);
- led_reg |= IXGBE_LED_BLINK(index);
- IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
- IXGBE_WRITE_FLUSH(hw);
-
- return 0;
-}
-
-/**
- * ixgbe_blink_led_stop_82598 - Stop blinking LED based on index.
- * @hw: pointer to hardware structure
- * @index: led number to stop blinking
- **/
-static s32 ixgbe_blink_led_stop_82598(struct ixgbe_hw *hw, u32 index)
-{
- u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
-
- autoc_reg &= ~IXGBE_AUTOC_FLU;
- autoc_reg |= IXGBE_AUTOC_AN_RESTART;
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
-
- led_reg &= ~IXGBE_LED_MODE_MASK(index);
- led_reg &= ~IXGBE_LED_BLINK(index);
- led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
- IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
- IXGBE_WRITE_FLUSH(hw);
-
- return 0;
-}
-
-/**
* ixgbe_read_analog_reg8_82598 - Reads 8 bit Atlas analog register
* @hw: pointer to hardware structure
* @reg: analog register to read
.get_link_capabilities = &ixgbe_get_link_capabilities_82598,
.led_on = &ixgbe_led_on_generic,
.led_off = &ixgbe_led_off_generic,
- .blink_led_start = &ixgbe_blink_led_start_82598,
- .blink_led_stop = &ixgbe_blink_led_stop_82598,
+ .blink_led_start = &ixgbe_blink_led_start_generic,
+ .blink_led_stop = &ixgbe_blink_led_stop_generic,
.set_rar = &ixgbe_set_rar_generic,
.clear_rar = &ixgbe_clear_rar_generic,
.set_vmdq = &ixgbe_set_vmdq_82598,
s32 ixgbe_set_vfta_82599(struct ixgbe_hw *hw, u32 vlan,
u32 vind, bool vlan_on);
s32 ixgbe_clear_vfta_82599(struct ixgbe_hw *hw);
-s32 ixgbe_blink_led_stop_82599(struct ixgbe_hw *hw, u32 index);
-s32 ixgbe_blink_led_start_82599(struct ixgbe_hw *hw, u32 index);
s32 ixgbe_init_uta_tables_82599(struct ixgbe_hw *hw);
s32 ixgbe_read_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 *val);
s32 ixgbe_write_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 val);
}
/**
- * ixgbe_blink_led_start_82599 - Blink LED based on index.
- * @hw: pointer to hardware structure
- * @index: led number to blink
- **/
-s32 ixgbe_blink_led_start_82599(struct ixgbe_hw *hw, u32 index)
-{
- u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
-
- led_reg &= ~IXGBE_LED_MODE_MASK(index);
- led_reg |= IXGBE_LED_BLINK(index);
- IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
- IXGBE_WRITE_FLUSH(hw);
-
- return 0;
-}
-
-/**
- * ixgbe_blink_led_stop_82599 - Stop blinking LED based on index.
- * @hw: pointer to hardware structure
- * @index: led number to stop blinking
- **/
-s32 ixgbe_blink_led_stop_82599(struct ixgbe_hw *hw, u32 index)
-{
- u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
-
- led_reg &= ~IXGBE_LED_MODE_MASK(index);
- led_reg &= ~IXGBE_LED_BLINK(index);
- IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
- IXGBE_WRITE_FLUSH(hw);
-
- return 0;
-}
-
-/**
* ixgbe_init_uta_tables_82599 - Initialize the Unicast Table Array
* @hw: pointer to hardware structure
**/
.get_link_capabilities = &ixgbe_get_link_capabilities_82599,
.led_on = &ixgbe_led_on_generic,
.led_off = &ixgbe_led_off_generic,
- .blink_led_start = &ixgbe_blink_led_start_82599,
- .blink_led_stop = &ixgbe_blink_led_stop_82599,
+ .blink_led_start = &ixgbe_blink_led_start_generic,
+ .blink_led_stop = &ixgbe_blink_led_stop_generic,
.set_rar = &ixgbe_set_rar_generic,
.clear_rar = &ixgbe_clear_rar_generic,
.set_vmdq = &ixgbe_set_vmdq_82599,
return 0;
}
+
+/**
+ * ixgbe_blink_led_start_generic - Blink LED based on index.
+ * @hw: pointer to hardware structure
+ * @index: led number to blink
+ **/
+s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index)
+{
+ ixgbe_link_speed speed = 0;
+ bool link_up = 0;
+ u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
+
+ /*
+ * Link must be up to auto-blink the LEDs;
+ * Force it if link is down.
+ */
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+
+ if (!link_up) {
+ autoc_reg |= IXGBE_AUTOC_FLU;
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
+ msleep(10);
+ }
+
+ led_reg &= ~IXGBE_LED_MODE_MASK(index);
+ led_reg |= IXGBE_LED_BLINK(index);
+ IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
+ IXGBE_WRITE_FLUSH(hw);
+
+ return 0;
+}
+
+/**
+ * ixgbe_blink_led_stop_generic - Stop blinking LED based on index.
+ * @hw: pointer to hardware structure
+ * @index: led number to stop blinking
+ **/
+s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index)
+{
+ u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
+
+ autoc_reg &= ~IXGBE_AUTOC_FLU;
+ autoc_reg |= IXGBE_AUTOC_AN_RESTART;
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
+
+ led_reg &= ~IXGBE_LED_MODE_MASK(index);
+ led_reg &= ~IXGBE_LED_BLINK(index);
+ led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
+ IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
+ IXGBE_WRITE_FLUSH(hw);
+
+ return 0;
+}
s32 ixgbe_read_analog_reg8_generic(struct ixgbe_hw *hw, u32 reg, u8 *val);
s32 ixgbe_write_analog_reg8_generic(struct ixgbe_hw *hw, u32 reg, u8 val);
+s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index);
+s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index);
+
#define IXGBE_WRITE_REG(a, reg, value) writel((value), ((a)->hw_addr + (reg)))
#ifndef writeq
}
+static int ixgbe_wol_exclusion(struct ixgbe_adapter *adapter,
+ struct ethtool_wolinfo *wol)
+{
+ struct ixgbe_hw *hw = &adapter->hw;
+ int retval = 1;
+
+ switch(hw->device_id) {
+ case IXGBE_DEV_ID_82599_KX4:
+ retval = 0;
+ break;
+ default:
+ wol->supported = 0;
+ retval = 0;
+ }
+
+ return retval;
+}
+
static void ixgbe_get_wol(struct net_device *netdev,
struct ethtool_wolinfo *wol)
{
WAKE_BCAST | WAKE_MAGIC;
wol->wolopts = 0;
- if (!device_can_wakeup(&adapter->pdev->dev))
+ if (ixgbe_wol_exclusion(adapter, wol) ||
+ !device_can_wakeup(&adapter->pdev->dev))
return;
if (adapter->wol & IXGBE_WUFC_EX)
if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
return -EOPNOTSUPP;
+ if (ixgbe_wol_exclusion(adapter, wol))
+ return wol->wolopts ? -EOPNOTSUPP : 0;
+
adapter->wol = 0;
if (wol->wolopts & WAKE_UCAST)
**/
static void ixgbe_set_num_queues(struct ixgbe_adapter *adapter)
{
- /* Start with base case */
- adapter->num_rx_queues = 1;
- adapter->num_tx_queues = 1;
-
#ifdef CONFIG_IXGBE_DCB
if (ixgbe_set_dcb_queues(adapter))
- return;
+ goto done;
#endif
if (ixgbe_set_rss_queues(adapter))
- return;
+ goto done;
+
+ /* fallback to base case */
+ adapter->num_rx_queues = 1;
+ adapter->num_tx_queues = 1;
+
+done:
+ /* Notify the stack of the (possibly) reduced Tx Queue count. */
+ adapter->netdev->real_num_tx_queues = adapter->num_tx_queues;
}
static void ixgbe_acquire_msix_vectors(struct ixgbe_adapter *adapter,
}
out:
- /* Notify the stack of the (possibly) reduced Tx Queue count. */
- adapter->netdev->real_num_tx_queues = adapter->num_tx_queues;
-
return err;
}
return 0;
}
-
#endif /* CONFIG_PM */
-static int ixgbe_suspend(struct pci_dev *pdev, pm_message_t state)
+
+static int __ixgbe_shutdown(struct pci_dev *pdev, bool *enable_wake)
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct ixgbe_adapter *adapter = netdev_priv(netdev);
pci_enable_wake(pdev, PCI_D3cold, 0);
}
+ *enable_wake = !!wufc;
+
ixgbe_release_hw_control(adapter);
pci_disable_device(pdev);
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int ixgbe_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ int retval;
+ bool wake;
+
+ retval = __ixgbe_shutdown(pdev, &wake);
+ if (retval)
+ return retval;
+
+ if (wake) {
+ pci_prepare_to_sleep(pdev);
+ } else {
+ pci_wake_from_d3(pdev, false);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
return 0;
}
+#endif /* CONFIG_PM */
static void ixgbe_shutdown(struct pci_dev *pdev)
{
- ixgbe_suspend(pdev, PMSG_SUSPEND);
+ bool wake;
+
+ __ixgbe_shutdown(pdev, &wake);
+
+ if (system_state == SYSTEM_POWER_OFF) {
+ pci_wake_from_d3(pdev, wake);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
}
/**
int count = 0;
unsigned int f;
- r_idx = (adapter->num_tx_queues - 1) & skb->queue_mapping;
+ r_idx = skb->queue_mapping;
tx_ring = &adapter->tx_ring[r_idx];
if (adapter->vlgrp && vlan_tx_tag_present(skb)) {
nubus_writew(swab16(value), dev->mem_start + portno);
}
+static const struct net_device_ops mac89x0_netdev_ops = {
+ .ndo_open = net_open,
+ .ndo_stop = net_close,
+ .ndo_start_xmit = net_send_packet,
+ .ndo_get_stats = net_get_stats,
+ .ndo_set_multicast_list = set_multicast_list,
+ .ndo_set_mac_address = set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
/* Probe for the CS8900 card in slot E. We won't bother looking
anywhere else until we have a really good reason to do so. */
struct net_device * __init mac89x0_probe(int unit)
printk(" IRQ %d ADDR %pM\n", dev->irq, dev->dev_addr);
- dev->open = net_open;
- dev->stop = net_close;
- dev->hard_start_xmit = net_send_packet;
- dev->get_stats = net_get_stats;
- dev->set_multicast_list = &set_multicast_list;
- dev->set_mac_address = &set_mac_address;
+ dev->netdev_ops = &mac89x0_netdev_ops;
err = register_netdev(dev);
if (err)
return phy_mii_ioctl(phydev, if_mii(rq), cmd);
}
+static const struct net_device_ops macb_netdev_ops = {
+ .ndo_open = macb_open,
+ .ndo_stop = macb_close,
+ .ndo_start_xmit = macb_start_xmit,
+ .ndo_set_multicast_list = macb_set_rx_mode,
+ .ndo_get_stats = macb_get_stats,
+ .ndo_do_ioctl = macb_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __init macb_probe(struct platform_device *pdev)
{
struct eth_platform_data *pdata;
goto err_out_iounmap;
}
- dev->open = macb_open;
- dev->stop = macb_close;
- dev->hard_start_xmit = macb_start_xmit;
- dev->get_stats = macb_get_stats;
- dev->set_multicast_list = macb_set_rx_mode;
- dev->do_ioctl = macb_ioctl;
+ dev->netdev_ops = &macb_netdev_ops;
netif_napi_add(dev, &bp->napi, macb_poll, 64);
dev->ethtool_ops = &macb_ethtool_ops;
return err;
}
+static const struct net_device_ops macsonic_netdev_ops = {
+ .ndo_open = macsonic_open,
+ .ndo_stop = macsonic_close,
+ .ndo_start_xmit = sonic_send_packet,
+ .ndo_set_multicast_list = sonic_multicast_list,
+ .ndo_tx_timeout = sonic_tx_timeout,
+ .ndo_get_stats = sonic_get_stats,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __init macsonic_init(struct net_device *dev)
{
struct sonic_local* lp = netdev_priv(dev);
lp->rra_laddr = lp->rda_laddr + (SIZEOF_SONIC_RD * SONIC_NUM_RDS
* SONIC_BUS_SCALE(lp->dma_bitmode));
- dev->open = macsonic_open;
- dev->stop = macsonic_close;
- dev->hard_start_xmit = sonic_send_packet;
- dev->get_stats = sonic_get_stats;
- dev->set_multicast_list = &sonic_multicast_list;
- dev->tx_timeout = sonic_tx_timeout;
+ dev->netdev_ops = &macsonic_netdev_ops;
dev->watchdog_timeo = TX_TIMEOUT;
/*
lro_mgr->lro_arr = ss->rx_done.lro_desc;
lro_mgr->get_frag_header = myri10ge_get_frag_header;
lro_mgr->max_aggr = myri10ge_lro_max_pkts;
+ lro_mgr->frag_align_pad = 2;
if (lro_mgr->max_aggr > MAX_SKB_FRAGS)
lro_mgr->max_aggr = MAX_SKB_FRAGS;
#include <linux/mii.h>
#include <linux/phy.h>
#include <linux/phy_fixed.h>
+#include <linux/err.h>
#define MII_REGS_NUM 29
int ret;
pdev = platform_device_register_simple("Fixed MDIO bus", 0, NULL, 0);
- if (!pdev) {
- ret = -ENOMEM;
+ if (IS_ERR(pdev)) {
+ ret = PTR_ERR(pdev);
goto err_pdev;
}
#define MII_M1111_COPPER 0
#define MII_M1111_FIBER 1
+#define MII_88E1121_PHY_LED_CTRL 16
+#define MII_88E1121_PHY_LED_PAGE 3
+#define MII_88E1121_PHY_LED_DEF 0x0030
+#define MII_88E1121_PHY_PAGE 22
+
#define MII_M1011_PHY_STATUS 0x11
#define MII_M1011_PHY_STATUS_1000 0x8000
#define MII_M1011_PHY_STATUS_100 0x4000
return err;
}
+static int m88e1121_config_aneg(struct phy_device *phydev)
+{
+ int err, temp;
+
+ err = phy_write(phydev, MII_BMCR, BMCR_RESET);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, MII_M1011_PHY_SCR,
+ MII_M1011_PHY_SCR_AUTO_CROSS);
+ if (err < 0)
+ return err;
+
+ temp = phy_read(phydev, MII_88E1121_PHY_PAGE);
+
+ phy_write(phydev, MII_88E1121_PHY_PAGE, MII_88E1121_PHY_LED_PAGE);
+ phy_write(phydev, MII_88E1121_PHY_LED_CTRL, MII_88E1121_PHY_LED_DEF);
+ phy_write(phydev, MII_88E1121_PHY_PAGE, temp);
+
+ err = genphy_config_aneg(phydev);
+
+ return err;
+}
+
static int m88e1111_config_init(struct phy_device *phydev)
{
int err;
return 0;
}
+static int m88e1121_did_interrupt(struct phy_device *phydev)
+{
+ int imask;
+
+ imask = phy_read(phydev, MII_M1011_IEVENT);
+
+ if (imask & MII_M1011_IMASK_INIT)
+ return 1;
+
+ return 0;
+}
+
static struct phy_driver marvell_drivers[] = {
{
.phy_id = 0x01410c60,
.driver = {.owner = THIS_MODULE,},
},
{
+ .phy_id = 0x01410cb0,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1121R",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_aneg = &m88e1121_config_aneg,
+ .read_status = &marvell_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .did_interrupt = &m88e1121_did_interrupt,
+ .driver = { .owner = THIS_MODULE },
+ },
+ {
.phy_id = 0x01410cd0,
.phy_id_mask = 0xfffffff0,
.name = "Marvell 88E1145",
phydev->adjust_state = handler;
INIT_DELAYED_WORK(&phydev->state_queue, phy_state_machine);
- schedule_delayed_work(&phydev->state_queue, jiffies + HZ);
+ schedule_delayed_work(&phydev->state_queue, HZ);
}
/**
struct phy_device *phydev =
container_of(work, struct phy_device, phy_queue);
+ if (phydev->drv->did_interrupt &&
+ !phydev->drv->did_interrupt(phydev))
+ goto ignore;
+
err = phy_disable_interrupts(phydev);
if (err)
return;
+ignore:
+ atomic_dec(&phydev->irq_disable);
+ enable_irq(phydev->irq);
+ return;
+
irq_enable_err:
disable_irq(phydev->irq);
atomic_inc(&phydev->irq_disable);
if (err < 0)
phy_error(phydev);
- schedule_delayed_work(&phydev->state_queue,
- jiffies + PHY_STATE_TIME * HZ);
+ schedule_delayed_work(&phydev->state_queue, PHY_STATE_TIME * HZ);
}
WARN_ON(channel->rx_pkt != NULL);
efx_rx_strategy(channel);
-
- netif_napi_add(channel->napi_dev, &channel->napi_str,
- efx_poll, napi_weight);
}
}
efx_for_each_channel(channel, efx) {
channel->napi_dev = efx->net_dev;
+ netif_napi_add(channel->napi_dev, &channel->napi_str,
+ efx_poll, napi_weight);
}
return 0;
}
struct efx_channel *channel;
efx_for_each_channel(channel, efx) {
+ if (channel->napi_dev)
+ netif_napi_del(&channel->napi_str);
channel->napi_dev = NULL;
}
}
EFX_POPULATE_QWORD_1(phy_event, EV_CODE, GLOBAL_EV_DECODE);
if (EFX_IS10G(efx))
- EFX_SET_OWORD_FIELD(phy_event, XG_PHY_INTR, 1);
+ EFX_SET_QWORD_FIELD(phy_event, XG_PHY_INTR, 1);
else
- EFX_SET_OWORD_FIELD(phy_event, G_PHY0_INTR, 1);
+ EFX_SET_QWORD_FIELD(phy_event, G_PHY0_INTR, 1);
falcon_generate_event(&efx->channel[0], &phy_event);
}
return ret;
}
+static const struct net_device_ops sh_eth_netdev_ops = {
+ .ndo_open = sh_eth_open,
+ .ndo_stop = sh_eth_close,
+ .ndo_start_xmit = sh_eth_start_xmit,
+ .ndo_get_stats = sh_eth_get_stats,
+ .ndo_set_multicast_list = sh_eth_set_multicast_list,
+ .ndo_tx_timeout = sh_eth_tx_timeout,
+ .ndo_do_ioctl = sh_eth_do_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
static int sh_eth_drv_probe(struct platform_device *pdev)
{
int ret, i, devno = 0;
mdp->edmac_endian = pd->edmac_endian;
/* set function */
- ndev->open = sh_eth_open;
- ndev->hard_start_xmit = sh_eth_start_xmit;
- ndev->stop = sh_eth_close;
- ndev->get_stats = sh_eth_get_stats;
- ndev->set_multicast_list = sh_eth_set_multicast_list;
- ndev->do_ioctl = sh_eth_do_ioctl;
- ndev->tx_timeout = sh_eth_tx_timeout;
+ ndev->netdev_ops = &sh_eth_netdev_ops;
ndev->watchdog_timeo = TX_TIMEOUT;
mdp->post_rx = POST_RX >> (devno << 1);
if (netif_msg_ifdown(skge))
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
- netif_stop_queue(dev);
+ netif_tx_disable(dev);
if (hw->chip_id == CHIP_ID_GENESIS && hw->phy_type == SK_PHY_XMAC)
del_timer_sync(&skge->link_timer);
}
skge->tx_ring.to_clean = e;
- netif_wake_queue(dev);
}
static void skge_tx_timeout(struct net_device *dev)
skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_STOP);
skge_tx_clean(dev);
+ netif_wake_queue(dev);
}
static int skge_change_mtu(struct net_device *dev, int new_mtu)
return ERR_PTR(err);
}
+static const struct net_device_ops sun3_82586_netdev_ops = {
+ .ndo_open = sun3_82586_open,
+ .ndo_stop = sun3_82586_close,
+ .ndo_start_xmit = sun3_82586_send_packet,
+ .ndo_set_multicast_list = set_multicast_list,
+ .ndo_tx_timeout = sun3_82586_timeout,
+ .ndo_get_stats = sun3_82586_get_stats,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
static int __init sun3_82586_probe1(struct net_device *dev,int ioaddr)
{
int i, size, retval;
printk("Memaddr: 0x%lx, Memsize: %d, IRQ %d\n",dev->mem_start,size, dev->irq);
- dev->open = sun3_82586_open;
- dev->stop = sun3_82586_close;
- dev->get_stats = sun3_82586_get_stats;
- dev->tx_timeout = sun3_82586_timeout;
+ dev->netdev_ops = &sun3_82586_netdev_ops;
dev->watchdog_timeo = HZ/20;
- dev->hard_start_xmit = sun3_82586_send_packet;
- dev->set_multicast_list = set_multicast_list;
dev->if_port = 0;
return 0;
return 0;
}
+static const struct net_device_ops tc35815_netdev_ops = {
+ .ndo_open = tc35815_open,
+ .ndo_stop = tc35815_close,
+ .ndo_start_xmit = tc35815_send_packet,
+ .ndo_get_stats = tc35815_get_stats,
+ .ndo_set_multicast_list = tc35815_set_multicast_list,
+ .ndo_tx_timeout = tc35815_tx_timeout,
+ .ndo_do_ioctl = tc35815_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = tc35815_poll_controller,
+#endif
+};
+
static int __devinit tc35815_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
ioaddr = pcim_iomap_table(pdev)[1];
/* Initialize the device structure. */
- dev->open = tc35815_open;
- dev->hard_start_xmit = tc35815_send_packet;
- dev->stop = tc35815_close;
- dev->get_stats = tc35815_get_stats;
- dev->set_multicast_list = tc35815_set_multicast_list;
- dev->do_ioctl = tc35815_ioctl;
+ dev->netdev_ops = &tc35815_netdev_ops;
dev->ethtool_ops = &tc35815_ethtool_ops;
- dev->tx_timeout = tc35815_tx_timeout;
dev->watchdog_timeo = TC35815_TX_TIMEOUT;
#ifdef TC35815_NAPI
netif_napi_add(dev, &lp->napi, tc35815_poll, NAPI_WEIGHT);
#endif
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = tc35815_poll_controller;
-#endif
dev->irq = pdev->irq;
dev->base_addr = (unsigned long)ioaddr;
/* Next, try NVRAM. */
if (!tg3_nvram_read_be32(tp, mac_offset + 0, &hi) &&
!tg3_nvram_read_be32(tp, mac_offset + 4, &lo)) {
- memcpy(&dev->dev_addr[0], ((char *)&hi) + 2, 2);
- memcpy(&dev->dev_addr[2], (char *)&lo, sizeof(lo));
+ dev->dev_addr[0] = ((hi >> 16) & 0xff);
+ dev->dev_addr[1] = ((hi >> 24) & 0xff);
+ dev->dev_addr[2] = ((lo >> 0) & 0xff);
+ dev->dev_addr[3] = ((lo >> 8) & 0xff);
+ dev->dev_addr[4] = ((lo >> 16) & 0xff);
+ dev->dev_addr[5] = ((lo >> 24) & 0xff);
+
}
/* Finally just fetch it out of the MAC control regs. */
else {
.set_settings = tsi108_set_settings,
};
+static const struct net_device_ops tsi108_netdev_ops = {
+ .ndo_open = tsi108_open,
+ .ndo_stop = tsi108_close,
+ .ndo_start_xmit = tsi108_send_packet,
+ .ndo_set_multicast_list = tsi108_set_rx_mode,
+ .ndo_get_stats = tsi108_get_stats,
+ .ndo_do_ioctl = tsi108_do_ioctl,
+ .ndo_set_mac_address = tsi108_set_mac,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
static int
tsi108_init_one(struct platform_device *pdev)
{
data->phy_type = einfo->phy_type;
data->irq_num = einfo->irq_num;
data->id = pdev->id;
- dev->open = tsi108_open;
- dev->stop = tsi108_close;
- dev->hard_start_xmit = tsi108_send_packet;
- dev->set_mac_address = tsi108_set_mac;
- dev->set_multicast_list = tsi108_set_rx_mode;
- dev->get_stats = tsi108_get_stats;
netif_napi_add(dev, &data->napi, tsi108_poll, 64);
- dev->do_ioctl = tsi108_do_ioctl;
+ dev->netdev_ops = &tsi108_netdev_ops;
dev->ethtool_ops = &tsi108_ethtool_ops;
/* Apparently, the Linux networking code won't use scatter-gather
int err;
/* Under a page? Don't bother with paged skb. */
- if (prepad + len < PAGE_SIZE)
+ if (prepad + len < PAGE_SIZE || !linear)
linear = len;
skb = sock_alloc_send_pskb(sk, prepad + linear, len - linear, noblock,
if ((tun->flags & TUN_TYPE_MASK) == TUN_TAP_DEV) {
align = NET_IP_ALIGN;
- if (unlikely(len < ETH_HLEN))
+ if (unlikely(len < ETH_HLEN ||
+ (gso.hdr_len && gso.hdr_len < ETH_HLEN)))
return -EINVAL;
}
static int velocity_open(struct net_device *dev);
static int velocity_change_mtu(struct net_device *dev, int mtu);
static int velocity_xmit(struct sk_buff *skb, struct net_device *dev);
-static int velocity_intr(int irq, void *dev_instance);
+static irqreturn_t velocity_intr(int irq, void *dev_instance);
static void velocity_set_multi(struct net_device *dev);
static struct net_device_stats *velocity_get_stats(struct net_device *dev);
static int velocity_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
* efficiently as possible.
*/
-static int velocity_intr(int irq, void *dev_instance)
+static irqreturn_t velocity_intr(int irq, void *dev_instance)
{
struct net_device *dev = dev_instance;
struct velocity_info *vptr = netdev_priv(dev);
return err;
}
+static const struct net_device_ops xtsonic_netdev_ops = {
+ .ndo_open = xtsonic_open,
+ .ndo_stop = xtsonic_close,
+ .ndo_start_xmit = sonic_send_packet,
+ .ndo_get_stats = sonic_get_stats,
+ .ndo_set_multicast_list = sonic_multicast_list,
+ .ndo_tx_timeout = sonic_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+};
+
static int __init sonic_probe1(struct net_device *dev)
{
static unsigned version_printed = 0;
lp->rra_laddr = lp->rda_laddr + (SIZEOF_SONIC_RD * SONIC_NUM_RDS
* SONIC_BUS_SCALE(lp->dma_bitmode));
- dev->open = xtsonic_open;
- dev->stop = xtsonic_close;
- dev->hard_start_xmit = sonic_send_packet;
- dev->get_stats = sonic_get_stats;
- dev->set_multicast_list = &sonic_multicast_list;
- dev->tx_timeout = sonic_tx_timeout;
+ dev->netdev_ops = &xtsonic_netdev_ops;
dev->watchdog_timeo = TX_TIMEOUT;
/*
#include <linux/slab.h>
#include <linux/buffer_head.h>
#include <linux/hdreg.h>
+#include <linux/async.h>
#include <asm/ccwdev.h>
#include <asm/ebcdic.h>
if (rc && rc != -EAGAIN)
device->target = device->state;
- if (device->state == device->target)
+ if (device->state == device->target) {
wake_up(&dasd_init_waitq);
+ dasd_put_device(device);
+ }
/* let user-space know that the device status changed */
kobject_uevent(&device->cdev->dev.kobj, KOBJ_CHANGE);
*/
void dasd_set_target_state(struct dasd_device *device, int target)
{
+ dasd_get_device(device);
/* If we are in probeonly mode stop at DASD_STATE_READY. */
if (dasd_probeonly && target > DASD_STATE_READY)
target = DASD_STATE_READY;
if (device->target != target) {
- if (device->state == target)
+ if (device->state == target) {
wake_up(&dasd_init_waitq);
+ dasd_put_device(device);
+ }
device->target = target;
}
if (device->state != device->target)
* SECTION: common functions for ccw_driver use
*/
+static void dasd_generic_auto_online(void *data, async_cookie_t cookie)
+{
+ struct ccw_device *cdev = data;
+ int ret;
+
+ ret = ccw_device_set_online(cdev);
+ if (ret)
+ pr_warning("%s: Setting the DASD online failed with rc=%d\n",
+ dev_name(&cdev->dev), ret);
+ else {
+ struct dasd_device *device = dasd_device_from_cdev(cdev);
+ wait_event(dasd_init_waitq, _wait_for_device(device));
+ dasd_put_device(device);
+ }
+}
+
/*
* Initial attempt at a probe function. this can be simplified once
* the other detection code is gone.
*/
if ((dasd_get_feature(cdev, DASD_FEATURE_INITIAL_ONLINE) > 0 ) ||
(dasd_autodetect && dasd_busid_known(dev_name(&cdev->dev)) != 0))
- ret = ccw_device_set_online(cdev);
- if (ret)
- pr_warning("%s: Setting the DASD online failed with rc=%d\n",
- dev_name(&cdev->dev), ret);
+ async_schedule(dasd_generic_auto_online, cdev);
return 0;
}
} else
pr_debug("dasd_generic device %s found\n",
dev_name(&cdev->dev));
-
- /* FIXME: we have to wait for the root device but we don't want
- * to wait for each single device but for all at once. */
- wait_event(dasd_init_waitq, _wait_for_device(device));
-
dasd_put_device(device);
-
return rc;
}
ccw++;
recid += count;
new_track = 0;
+ /* first idaw for a ccw may start anywhere */
+ if (!idaw_dst)
+ idaw_dst = dst;
}
- /* If we start a new idaw, everything is fine and the
- * start of the new idaw is the start of this segment.
+ /* If we start a new idaw, we must make sure that it
+ * starts on an IDA_BLOCK_SIZE boundary.
* If we continue an idaw, we must make sure that the
* current segment begins where the so far accumulated
* idaw ends
*/
- if (!idaw_dst)
- idaw_dst = dst;
+ if (!idaw_dst) {
+ if (__pa(dst) & (IDA_BLOCK_SIZE-1)) {
+ dasd_sfree_request(cqr, startdev);
+ return ERR_PTR(-ERANGE);
+ } else
+ idaw_dst = dst;
+ }
if ((idaw_dst + idaw_len) != dst) {
dasd_sfree_request(cqr, startdev);
return ERR_PTR(-ERANGE);
qdio_set_state(irq_ptr, QDIO_IRQ_STATE_STOPPED);
}
-static void qdio_call_shutdown(struct work_struct *work)
-{
- struct ccw_device_private *priv;
- struct ccw_device *cdev;
-
- priv = container_of(work, struct ccw_device_private, kick_work);
- cdev = priv->cdev;
- qdio_shutdown(cdev, QDIO_FLAG_CLEANUP_USING_CLEAR);
- put_device(&cdev->dev);
-}
-
-static void qdio_int_error(struct ccw_device *cdev)
-{
- struct qdio_irq *irq_ptr = cdev->private->qdio_data;
-
- switch (irq_ptr->state) {
- case QDIO_IRQ_STATE_INACTIVE:
- case QDIO_IRQ_STATE_CLEANUP:
- qdio_set_state(irq_ptr, QDIO_IRQ_STATE_ERR);
- break;
- case QDIO_IRQ_STATE_ESTABLISHED:
- case QDIO_IRQ_STATE_ACTIVE:
- qdio_set_state(irq_ptr, QDIO_IRQ_STATE_STOPPED);
- if (get_device(&cdev->dev)) {
- /* Can't call shutdown from interrupt context. */
- PREPARE_WORK(&cdev->private->kick_work,
- qdio_call_shutdown);
- queue_work(ccw_device_work, &cdev->private->kick_work);
- }
- break;
- default:
- WARN_ON(1);
- }
- wake_up(&cdev->private->wait_q);
-}
-
static int qdio_establish_check_errors(struct ccw_device *cdev, int cstat,
int dstat)
{
switch (PTR_ERR(irb)) {
case -EIO:
DBF_ERROR("%4x IO error", irq_ptr->schid.sch_no);
- return;
- case -ETIMEDOUT:
- DBF_ERROR("%4x IO timeout", irq_ptr->schid.sch_no);
- qdio_int_error(cdev);
+ qdio_set_state(irq_ptr, QDIO_IRQ_STATE_ERR);
+ wake_up(&cdev->private->wait_q);
return;
default:
WARN_ON(1);
case QDIO_IRQ_STATE_ACTIVE:
if (cstat & SCHN_STAT_PCI) {
qdio_int_handler_pci(irq_ptr);
- /* no state change so no need to wake up wait_q */
return;
}
if ((cstat & ~SCHN_STAT_PCI) || dstat) {
return 0;
}
-static int jsf_ioctl(struct inode *inode, struct file *f, unsigned int cmd,
- unsigned long arg)
+static long jsf_ioctl(struct file *f, unsigned int cmd, unsigned long arg)
{
+ lock_kernel();
int error = -ENOTTY;
void __user *argp = (void __user *)arg;
- if (!capable(CAP_SYS_ADMIN))
+ if (!capable(CAP_SYS_ADMIN)) {
+ unlock_kernel();
return -EPERM;
+ }
switch (cmd) {
case JSFLASH_IDENT:
- if (copy_to_user(argp, &jsf0.id, JSFIDSZ))
+ if (copy_to_user(argp, &jsf0.id, JSFIDSZ)) {
+ unlock_kernel();
return -EFAULT;
+ }
break;
case JSFLASH_ERASE:
error = jsf_ioctl_erase(arg);
break;
}
+ unlock_kernel();
return error;
}
.llseek = jsf_lseek,
.read = jsf_read,
.write = jsf_write,
- .ioctl = jsf_ioctl,
+ .unlocked_ioctl = jsf_ioctl,
.mmap = jsf_mmap,
.open = jsf_open,
.release = jsf_release,
static void uctrl_get_event_status(struct uctrl_driver *);
static void uctrl_get_external_status(struct uctrl_driver *);
-static int
-uctrl_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long
+uctrl_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
switch (cmd) {
default:
static const struct file_operations uctrl_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
- .ioctl = uctrl_ioctl,
+ .unlocked_ioctl = uctrl_ioctl,
.open = uctrl_open,
};
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (tx_enabled(port)) {
- disable_irq(ourport->tx_irq);
+ disable_irq_nosync(ourport->tx_irq);
tx_enabled(port) = 0;
if (port->flags & UPF_CONS_FLOW)
s3c24xx_serial_rx_enable(port);
if (rx_enabled(port)) {
dbg("s3c24xx_serial_stop_rx: port=%p\n", port);
- disable_irq(ourport->rx_irq);
+ disable_irq_nosync(ourport->rx_irq);
rx_enabled(port) = 0;
}
}
struct chip_data *chip = drv_data->cur_chip;
if (chip->cs_control) {
- chip->cs_control(PXA2XX_CS_ASSERT);
+ chip->cs_control(PXA2XX_CS_DEASSERT);
return;
}
static struct proc_dir_entry *binder_proc_dir_entry_root;
static struct proc_dir_entry *binder_proc_dir_entry_proc;
static struct hlist_head binder_dead_nodes;
+static HLIST_HEAD(binder_deferred_list);
+static DEFINE_MUTEX(binder_deferred_lock);
static int binder_read_proc_proc(
char *page, char **start, off_t off, int count, int *eof, void *data);
#define SZ_4M 0x400000
#endif
-#ifndef __i386__
-#define FORBIDDEN_MMAP_FLAGS (VM_WRITE | VM_EXEC)
-#else
#define FORBIDDEN_MMAP_FLAGS (VM_WRITE)
-#endif
#define BINDER_SMALL_BUF_SIZE (PAGE_SIZE * 64)
uint8_t data[0];
};
+enum {
+ BINDER_DEFERRED_PUT_FILES = 0x01,
+ BINDER_DEFERRED_FLUSH = 0x02,
+ BINDER_DEFERRED_RELEASE = 0x04,
+};
+
struct binder_proc {
struct hlist_node proc_node;
struct rb_root threads;
int pid;
struct vm_area_struct *vma;
struct task_struct *tsk;
+ struct files_struct *files;
+ struct hlist_node deferred_work_node;
+ int deferred_work;
void *buffer;
- size_t user_buffer_offset;
+ ptrdiff_t user_buffer_offset;
struct list_head buffers;
struct rb_root free_buffers;
uid_t sender_euid;
};
+static void binder_defer_work(struct binder_proc *proc, int defer);
+
/*
* copied from get_unused_fd_flags
*/
-int task_get_unused_fd_flags(struct task_struct *tsk, int flags)
+int task_get_unused_fd_flags(struct binder_proc *proc, int flags)
{
- struct files_struct *files = get_files_struct(tsk);
+ struct files_struct *files = proc->files;
int fd, error;
struct fdtable *fdt;
unsigned long rlim_cur;
* will limit the total number of files that can be opened.
*/
rlim_cur = 0;
- if (lock_task_sighand(tsk, &irqs)) {
- rlim_cur = tsk->signal->rlim[RLIMIT_NOFILE].rlim_cur;
- unlock_task_sighand(tsk, &irqs);
+ if (lock_task_sighand(proc->tsk, &irqs)) {
+ rlim_cur = proc->tsk->signal->rlim[RLIMIT_NOFILE].rlim_cur;
+ unlock_task_sighand(proc->tsk, &irqs);
}
if (fd >= rlim_cur)
goto out;
out:
spin_unlock(&files->file_lock);
- put_files_struct(files);
return error;
}
* copied from fd_install
*/
static void task_fd_install(
- struct task_struct *tsk, unsigned int fd, struct file *file)
+ struct binder_proc *proc, unsigned int fd, struct file *file)
{
- struct files_struct *files = get_files_struct(tsk);
+ struct files_struct *files = proc->files;
struct fdtable *fdt;
if (files == NULL)
BUG_ON(fdt->fd[fd] != NULL);
rcu_assign_pointer(fdt->fd[fd], file);
spin_unlock(&files->file_lock);
- put_files_struct(files);
}
/*
/*
* copied from sys_close
*/
-static long task_close_fd(struct task_struct *tsk, unsigned int fd)
+static long task_close_fd(struct binder_proc *proc, unsigned int fd)
{
struct file *filp;
- struct files_struct *files = get_files_struct(tsk);
+ struct files_struct *files = proc->files;
struct fdtable *fdt;
int retval;
retval == -ERESTART_RESTARTBLOCK))
retval = -EINTR;
- put_files_struct(files);
return retval;
out_unlock:
spin_unlock(&files->file_lock);
- put_files_struct(files);
return -EBADF;
}
proc->pid, page_addr);
goto err_map_kernel_failed;
}
- user_page_addr = (size_t)page_addr + proc->user_buffer_offset;
+ user_page_addr =
+ (uintptr_t)page_addr + proc->user_buffer_offset;
ret = vm_insert_page(vma, user_page_addr, page[0]);
if (ret) {
printk(KERN_ERR "binder: %d: binder_alloc_buf failed "
page_addr -= PAGE_SIZE) {
page = &proc->pages[(page_addr - proc->buffer) / PAGE_SIZE];
if (vma)
- zap_page_range(vma, (size_t)page_addr +
+ zap_page_range(vma, (uintptr_t)page_addr +
proc->user_buffer_offset, PAGE_SIZE, NULL);
err_vm_insert_page_failed:
unmap_kernel_range((unsigned long)page_addr, PAGE_SIZE);
"er %p size %zd\n", proc->pid, size, buffer, buffer_size);
has_page_addr =
- (void *)(((size_t)buffer->data + buffer_size) & PAGE_MASK);
+ (void *)(((uintptr_t)buffer->data + buffer_size) & PAGE_MASK);
if (n == NULL) {
if (size + sizeof(struct binder_buffer) + 4 >= buffer_size)
buffer_size = size; /* no room for other buffers */
else
buffer_size = size + sizeof(struct binder_buffer);
}
- end_page_addr = (void *)PAGE_ALIGN((size_t)buffer->data + buffer_size);
+ end_page_addr =
+ (void *)PAGE_ALIGN((uintptr_t)buffer->data + buffer_size);
if (end_page_addr > has_page_addr)
end_page_addr = has_page_addr;
if (binder_update_page_range(proc, 1,
- (void *)PAGE_ALIGN((size_t)buffer->data), end_page_addr, NULL))
+ (void *)PAGE_ALIGN((uintptr_t)buffer->data), end_page_addr, NULL))
return NULL;
rb_erase(best_fit, &proc->free_buffers);
static void *buffer_start_page(struct binder_buffer *buffer)
{
- return (void *)((size_t)buffer & PAGE_MASK);
+ return (void *)((uintptr_t)buffer & PAGE_MASK);
}
static void *buffer_end_page(struct binder_buffer *buffer)
{
- return (void *)(((size_t)(buffer + 1) - 1) & PAGE_MASK);
+ return (void *)(((uintptr_t)(buffer + 1) - 1) & PAGE_MASK);
}
static void binder_delete_free_buffer(
}
binder_update_page_range(proc, 0,
- (void *)PAGE_ALIGN((size_t)buffer->data),
- (void *)(((size_t)buffer->data + buffer_size) & PAGE_MASK),
+ (void *)PAGE_ALIGN((uintptr_t)buffer->data),
+ (void *)(((uintptr_t)buffer->data + buffer_size) & PAGE_MASK),
NULL);
rb_erase(&buffer->rb_node, &proc->allocated_buffers);
buffer->free = 1;
if (!(tr->flags & TF_ONE_WAY) && thread->transaction_stack) {
struct binder_transaction *tmp;
tmp = thread->transaction_stack;
+ if (tmp->to_thread != thread) {
+ binder_user_error("binder: %d:%d got new "
+ "transaction with bad transaction stack"
+ ", transaction %d has target %d:%d\n",
+ proc->pid, thread->pid, tmp->debug_id,
+ tmp->to_proc ? tmp->to_proc->pid : 0,
+ tmp->to_thread ?
+ tmp->to_thread->pid : 0);
+ return_error = BR_FAILED_REPLY;
+ goto err_bad_call_stack;
+ }
while (tmp) {
if (tmp->from && tmp->from->proc == target_proc)
target_thread = tmp->from;
return_error = BR_FAILED_REPLY;
goto err_copy_data_failed;
}
+ if (!IS_ALIGNED(tr->offsets_size, sizeof(size_t))) {
+ binder_user_error("binder: %d:%d got transaction with "
+ "invalid offsets size, %zd\n",
+ proc->pid, thread->pid, tr->offsets_size);
+ return_error = BR_FAILED_REPLY;
+ goto err_bad_offset;
+ }
off_end = (void *)offp + tr->offsets_size;
for (; offp < off_end; offp++) {
struct flat_binder_object *fp;
- if (*offp > t->buffer->data_size - sizeof(*fp)) {
+ if (*offp > t->buffer->data_size - sizeof(*fp) ||
+ t->buffer->data_size < sizeof(*fp) ||
+ !IS_ALIGNED(*offp, sizeof(void *))) {
binder_user_error("binder: %d:%d got transaction with "
"invalid offset, %zd\n",
proc->pid, thread->pid, *offp);
return_error = BR_FAILED_REPLY;
goto err_fget_failed;
}
- target_fd = task_get_unused_fd_flags(target_proc->tsk, O_CLOEXEC);
+ target_fd = task_get_unused_fd_flags(target_proc, O_CLOEXEC);
if (target_fd < 0) {
fput(file);
return_error = BR_FAILED_REPLY;
goto err_get_unused_fd_failed;
}
- task_fd_install(target_proc->tsk, target_fd, file);
+ task_fd_install(target_proc, target_fd, file);
if (binder_debug_mask & BINDER_DEBUG_TRANSACTION)
printk(KERN_INFO " fd %ld -> %d\n", fp->handle, target_fd);
/* TODO: fput? */
off_end = (void *)offp + buffer->offsets_size;
for (; offp < off_end; offp++) {
struct flat_binder_object *fp;
- if (*offp > buffer->data_size - sizeof(*fp)) {
+ if (*offp > buffer->data_size - sizeof(*fp) ||
+ buffer->data_size < sizeof(*fp) ||
+ !IS_ALIGNED(*offp, sizeof(void *))) {
printk(KERN_ERR "binder: transaction release %d bad"
"offset %zd, size %zd\n", debug_id, *offp, buffer->data_size);
continue;
if (binder_debug_mask & BINDER_DEBUG_TRANSACTION)
printk(KERN_INFO " fd %ld\n", fp->handle);
if (failed_at)
- task_close_fd(proc->tsk, fp->handle);
+ task_close_fd(proc, fp->handle);
break;
default:
tr.data_size = t->buffer->data_size;
tr.offsets_size = t->buffer->offsets_size;
- tr.data.ptr.buffer = (void *)((void *)t->buffer->data + proc->user_buffer_offset);
+ tr.data.ptr.buffer = (void *)t->buffer->data + proc->user_buffer_offset;
tr.data.ptr.offsets = tr.data.ptr.buffer + ALIGN(t->buffer->data_size, sizeof(void *));
if (put_user(cmd, (uint32_t __user *)ptr))
(unsigned long)pgprot_val(vma->vm_page_prot));
dump_stack();
}
+
static void binder_vma_close(struct vm_area_struct *vma)
{
struct binder_proc *proc = vma->vm_private_data;
(vma->vm_end - vma->vm_start) / SZ_1K, vma->vm_flags,
(unsigned long)pgprot_val(vma->vm_page_prot));
proc->vma = NULL;
+ binder_defer_work(proc, BINDER_DEFERRED_PUT_FILES);
}
static struct vm_operations_struct binder_vm_ops = {
}
vma->vm_flags = (vma->vm_flags | VM_DONTCOPY) & ~VM_MAYWRITE;
+ if (proc->buffer) {
+ ret = -EBUSY;
+ failure_string = "already mapped";
+ goto err_already_mapped;
+ }
+
area = get_vm_area(vma->vm_end - vma->vm_start, VM_IOREMAP);
if (area == NULL) {
ret = -ENOMEM;
goto err_get_vm_area_failed;
}
proc->buffer = area->addr;
- proc->user_buffer_offset = vma->vm_start - (size_t)proc->buffer;
+ proc->user_buffer_offset = vma->vm_start - (uintptr_t)proc->buffer;
#ifdef CONFIG_CPU_CACHE_VIPT
if (cache_is_vipt_aliasing()) {
binder_insert_free_buffer(proc, buffer);
proc->free_async_space = proc->buffer_size / 2;
barrier();
+ proc->files = get_files_struct(current);
proc->vma = vma;
/*printk(KERN_INFO "binder_mmap: %d %lx-%lx maps %p\n", proc->pid, vma->vm_start, vma->vm_end, proc->buffer);*/
err_alloc_small_buf_failed:
kfree(proc->pages);
+ proc->pages = NULL;
err_alloc_pages_failed:
vfree(proc->buffer);
+ proc->buffer = NULL;
err_get_vm_area_failed:
- mutex_unlock(&binder_lock);
+err_already_mapped:
err_bad_arg:
printk(KERN_ERR "binder_mmap: %d %lx-%lx %s failed %d\n", proc->pid, vma->vm_start, vma->vm_end, failure_string, ret);
return ret;
if (binder_proc_dir_entry_proc) {
char strbuf[11];
snprintf(strbuf, sizeof(strbuf), "%u", proc->pid);
+ remove_proc_entry(strbuf, binder_proc_dir_entry_proc);
create_proc_read_entry(strbuf, S_IRUGO, binder_proc_dir_entry_proc, binder_read_proc_proc, proc);
}
static int binder_flush(struct file *filp, fl_owner_t id)
{
- struct rb_node *n;
struct binder_proc *proc = filp->private_data;
- int wake_count = 0;
- mutex_lock(&binder_lock);
+ binder_defer_work(proc, BINDER_DEFERRED_FLUSH);
+
+ return 0;
+}
+
+static void binder_deferred_flush(struct binder_proc *proc)
+{
+ struct rb_node *n;
+ int wake_count = 0;
for (n = rb_first(&proc->threads); n != NULL; n = rb_next(n)) {
struct binder_thread *thread = rb_entry(n, struct binder_thread, rb_node);
thread->looper |= BINDER_LOOPER_STATE_NEED_RETURN;
}
}
wake_up_interruptible_all(&proc->wait);
- mutex_unlock(&binder_lock);
if (binder_debug_mask & BINDER_DEBUG_OPEN_CLOSE)
printk(KERN_INFO "binder_flush: %d woke %d threads\n", proc->pid, wake_count);
-
- return 0;
}
static int binder_release(struct inode *nodp, struct file *filp)
{
- struct hlist_node *pos;
- struct binder_transaction *t;
- struct rb_node *n;
struct binder_proc *proc = filp->private_data;
- int threads, nodes, incoming_refs, outgoing_refs, buffers, active_transactions, page_count;
-
if (binder_proc_dir_entry_proc) {
char strbuf[11];
snprintf(strbuf, sizeof(strbuf), "%u", proc->pid);
remove_proc_entry(strbuf, binder_proc_dir_entry_proc);
}
- mutex_lock(&binder_lock);
+
+ binder_defer_work(proc, BINDER_DEFERRED_RELEASE);
+
+ return 0;
+}
+
+static void binder_deferred_release(struct binder_proc *proc)
+{
+ struct hlist_node *pos;
+ struct binder_transaction *t;
+ struct rb_node *n;
+ int threads, nodes, incoming_refs, outgoing_refs, buffers, active_transactions, page_count;
+
+ BUG_ON(proc->vma);
+ BUG_ON(proc->files);
+
hlist_del(&proc->proc_node);
if (binder_context_mgr_node && binder_context_mgr_node->proc == proc) {
if (binder_debug_mask & BINDER_DEBUG_DEAD_BINDER)
}
binder_stats.obj_deleted[BINDER_STAT_PROC]++;
- mutex_unlock(&binder_lock);
page_count = 0;
if (proc->pages) {
proc->pid, threads, nodes, incoming_refs, outgoing_refs, active_transactions, buffers, page_count);
kfree(proc);
- return 0;
+}
+
+static void binder_deferred_func(struct work_struct *work)
+{
+ struct binder_proc *proc;
+ struct files_struct *files;
+
+ int defer;
+ do {
+ mutex_lock(&binder_lock);
+ mutex_lock(&binder_deferred_lock);
+ if (!hlist_empty(&binder_deferred_list)) {
+ proc = hlist_entry(binder_deferred_list.first,
+ struct binder_proc, deferred_work_node);
+ hlist_del_init(&proc->deferred_work_node);
+ defer = proc->deferred_work;
+ proc->deferred_work = 0;
+ } else {
+ proc = NULL;
+ defer = 0;
+ }
+ mutex_unlock(&binder_deferred_lock);
+
+ files = NULL;
+ if (defer & BINDER_DEFERRED_PUT_FILES)
+ if ((files = proc->files))
+ proc->files = NULL;
+
+ if (defer & BINDER_DEFERRED_FLUSH)
+ binder_deferred_flush(proc);
+
+ if (defer & BINDER_DEFERRED_RELEASE)
+ binder_deferred_release(proc); /* frees proc */
+
+ mutex_unlock(&binder_lock);
+ if (files)
+ put_files_struct(files);
+ } while (proc);
+}
+static DECLARE_WORK(binder_deferred_work, binder_deferred_func);
+
+static void binder_defer_work(struct binder_proc *proc, int defer)
+{
+ mutex_lock(&binder_deferred_lock);
+ proc->deferred_work |= defer;
+ if (hlist_unhashed(&proc->deferred_work_node)) {
+ hlist_add_head(&proc->deferred_work_node,
+ &binder_deferred_list);
+ schedule_work(&binder_deferred_work);
+ }
+ mutex_unlock(&binder_deferred_lock);
}
static char *print_binder_transaction(char *buf, char *end, const char *prefix, struct binder_transaction *t)
return 0;
}
+static const struct net_device_ops at76_netdev_ops = {
+ .ndo_open = at76_open,
+ .ndo_stop = at76_stop,
+ .ndo_get_stats = at76_get_stats,
+ .ndo_start_xmit = at76_tx,
+ .ndo_tx_timeout = at76_tx_timeout,
+ .ndo_set_multicast_list = at76_set_multicast,
+ .ndo_set_mac_address = at76_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
/* Register network device and initialize the hardware */
static int at76_init_new_device(struct at76_priv *priv,
struct usb_interface *interface)
priv->scan_mode = SCAN_TYPE_ACTIVE;
netdev->flags &= ~IFF_MULTICAST; /* not yet or never */
- netdev->open = at76_open;
- netdev->stop = at76_stop;
- netdev->get_stats = at76_get_stats;
+ netdev->netdev_ops = &at76_netdev_ops;
netdev->ethtool_ops = &at76_ethtool_ops;
/* Add pointers to enable iwspy support. */
priv->wireless_data.spy_data = &priv->spy_data;
netdev->wireless_data = &priv->wireless_data;
- netdev->hard_start_xmit = at76_tx;
- netdev->tx_timeout = at76_tx_timeout;
netdev->watchdog_timeo = 2 * HZ;
netdev->wireless_handlers = &at76_handler_def;
- netdev->set_multicast_list = at76_set_multicast;
- netdev->set_mac_address = at76_set_mac_address;
dev_alloc_name(netdev, "wlan%d");
ret = register_netdev(priv->netdev);
return Ret;
}
+static const struct net_device_ops epl_netdev_ops = {
+ .ndo_open = VEthOpen,
+ .ndo_stop = VEthClose,
+ .ndo_get_stats = VEthGetStats,
+ .ndo_start_xmit = VEthXmit,
+ .ndo_tx_timeout = VEthTimeout,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
tEplKernel VEthAddInstance(tEplDllkInitParam *pInitParam_p)
{
tEplKernel Ret = kEplSuccessful;
goto Exit;
}
- pVEthNetDevice_g->open = VEthOpen;
- pVEthNetDevice_g->stop = VEthClose;
- pVEthNetDevice_g->get_stats = VEthGetStats;
- pVEthNetDevice_g->hard_start_xmit = VEthXmit;
- pVEthNetDevice_g->tx_timeout = VEthTimeout;
+ pVEthNetDevice_g->netdev_ops = &epl_netdev_ops;
pVEthNetDevice_g->watchdog_timeo = EPL_VETH_TX_TIMEOUT;
pVEthNetDevice_g->destructor = free_netdev;
void et131x_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid);
void et131x_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid);
+static const struct net_device_ops et131x_netdev_ops = {
+ .ndo_open = et131x_open,
+ .ndo_stop = et131x_close,
+ .ndo_start_xmit = et131x_tx,
+ .ndo_set_multicast_list = et131x_multicast,
+ .ndo_tx_timeout = et131x_tx_timeout,
+ .ndo_change_mtu = et131x_change_mtu,
+ .ndo_set_mac_address = et131x_set_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_get_stats = et131x_stats,
+ .ndo_do_ioctl = et131x_ioctl,
+};
+
/**
* et131x_device_alloc
*
*/
//netdev->init = &et131x_init;
//netdev->set_config = &et131x_config;
- netdev->get_stats = &et131x_stats;
- netdev->open = &et131x_open;
- netdev->stop = &et131x_close;
- netdev->do_ioctl = &et131x_ioctl;
- netdev->set_multicast_list = &et131x_multicast;
- netdev->hard_start_xmit = &et131x_tx;
- netdev->tx_timeout = &et131x_tx_timeout;
netdev->watchdog_timeo = ET131X_TX_TIMEOUT;
- netdev->change_mtu = &et131x_change_mtu;
- netdev->set_mac_address = &et131x_set_mac_addr;
+ netdev->netdev_ops = &et131x_netdev_ops;
//netdev->ethtool_ops = &et131x_ethtool_ops;
init_i2c_module(&go->i2c_adapter,
go->board_info->i2c_devs[i].id,
go->board_info->i2c_devs[i].addr);
-#ifdef TUNER_SET_TYPE_ADDR
- if (go->tuner_type >= 0) {
- struct tuner_setup tun_setup = {
- .mode_mask = T_ANALOG_TV,
- .addr = ADDR_UNSET,
- .type = go->tuner_type
- };
- i2c_clients_command(&go->i2c_adapter,
- TUNER_SET_TYPE_ADDR, &tun_setup);
- }
-#else
- if (go->tuner_type >= 0)
- i2c_clients_command(&go->i2c_adapter,
- TUNER_SET_TYPE, &go->tuner_type);
-#endif
if (go->board_id == GO7007_BOARDID_ADLINK_MPG24)
i2c_clients_command(&go->i2c_adapter,
DECODER_SET_CHANNEL, &go->channel_number);
struct wis_sony_tuner *t = i2c_get_clientdata(client);
switch (cmd) {
+#if 0
#ifdef TUNER_SET_TYPE_ADDR
case TUNER_SET_TYPE_ADDR:
{
t->type, sony_tuners[t->type - 200].name);
break;
}
+#endif
case VIDIOC_G_FREQUENCY:
{
struct v4l2_frequency *f = arg;
{
static int dev;
struct snd_card *card;
+ int err;
- card = snd_card_new(line6_index[dev], line6_id[dev], THIS_MODULE, 0);
-
- if (card == NULL)
- return -ENOMEM;
+ err = snd_card_create(line6_index[dev], line6_id[dev], THIS_MODULE, 0,
+ &card);
+ if (err < 0)
+ return err;
line6->card = card;
return 0;
}
+static const struct net_device_ops vap_netdev_ops = {
+ .ndo_open = zfLnxVapOpen,
+ .ndo_stop = zfLnxVapClose,
+ .ndo_start_xmit = zfLnxVapXmitFrame,
+ .ndo_get_stats = usbdrv_get_stats,
+ .ndo_change_mtu = usbdrv_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+#ifdef ZM_HOSTAPD_SUPPORT
+ .ndo_do_ioctl = usbdrv_ioctl,
+#else
+ .ndo_do_ioctl = NULL,
+#endif
+};
+
int zfLnxRegisterVapDev(struct net_device* parentDev, u16_t vapId)
{
/* Allocate net device structure */
vap[vapId].dev->ml_priv = parentDev->ml_priv;
//dev->hard_start_xmit = &zd1212_wds_xmit_frame;
- vap[vapId].dev->hard_start_xmit = &zfLnxVapXmitFrame;
- vap[vapId].dev->open = &zfLnxVapOpen;
- vap[vapId].dev->stop = &zfLnxVapClose;
- vap[vapId].dev->get_stats = &usbdrv_get_stats;
- vap[vapId].dev->change_mtu = &usbdrv_change_mtu;
-#ifdef ZM_HOSTAPD_SUPPORT
- vap[vapId].dev->do_ioctl = usbdrv_ioctl;
-#else
- vap[vapId].dev->do_ioctl = NULL;
-#endif
+ vap[vapId].dev->netdev_ops = &vap_netdev_ops;
vap[vapId].dev->destructor = free_netdev;
vap[vapId].dev->tx_queue_len = 0;
usb_unlink_urb(macp->RegInUrb);
}
+static const struct net_device_ops otus_netdev_ops = {
+ .ndo_open = usbdrv_open,
+ .ndo_stop = usbdrv_close,
+ .ndo_start_xmit = usbdrv_xmit_frame,
+ .ndo_change_mtu = usbdrv_change_mtu,
+ .ndo_get_stats = usbdrv_get_stats,
+ .ndo_set_multicast_list = usbdrv_set_multi,
+ .ndo_set_mac_address = usbdrv_set_mac,
+ .ndo_do_ioctl = usbdrv_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
u8_t zfLnxInitSetup(struct net_device *dev, struct usbdrv_private *macp)
{
//unsigned char addr[6];
dev->wireless_handlers = (struct iw_handler_def *)&p80211wext_handler_def;
#endif
- dev->open = usbdrv_open;
- dev->hard_start_xmit = usbdrv_xmit_frame;
- dev->stop = usbdrv_close;
- dev->change_mtu = &usbdrv_change_mtu;
- dev->get_stats = usbdrv_get_stats;
- dev->set_multicast_list = usbdrv_set_multi;
- dev->set_mac_address = usbdrv_set_mac;
- dev->do_ioctl = usbdrv_ioctl;
+ dev->netdev_ops = &otus_netdev_ops;
dev->flags |= IFF_MULTICAST;
static struct usb_device_id zd1221_ids [] = {
{ USB_DEVICE(VENDOR_ATHR, PRODUCT_AR9170) },
{ USB_DEVICE(VENDOR_DLINK, PRODUCT_DWA160A) },
- { USB_DEVICE(0x0846, 0x9010) },
+ { USB_DEVICE(VENDOR_NETGEAR, PRODUCT_WNDA3100) },
+ { USB_DEVICE(VENDOR_NETGEAR, PRODUCT_WN111v2) },
{ } /* Terminating entry */
};
#define VENDOR_DLINK 0x07D1 //Dlink
#define PRODUCT_DWA160A 0x3C10
+#define VENDOR_NETGEAR 0x0846 /* NetGear */
+#define PRODUCT_WNDA3100 0x9010
+#define PRODUCT_WN111v2 0x9001
+
#endif
return g;
}
+static inline void pohmelfs_insert_config_entry(struct pohmelfs_sb *psb, struct pohmelfs_config *dst)
+{
+ struct pohmelfs_config *tmp;
+
+ INIT_LIST_HEAD(&dst->config_entry);
+
+ list_for_each_entry(tmp, &psb->state_list, config_entry) {
+ if (dst->state.ctl.prio > tmp->state.ctl.prio)
+ list_add_tail(&dst->config_entry, &tmp->config_entry);
+ }
+ if (list_empty(&dst->config_entry))
+ list_add_tail(&dst->config_entry, &psb->state_list);
+}
+
+static int pohmelfs_move_config_entry(struct pohmelfs_sb *psb,
+ struct pohmelfs_config *dst, struct pohmelfs_config *new)
+{
+ if ((dst->state.ctl.prio == new->state.ctl.prio) &&
+ (dst->state.ctl.perm == new->state.ctl.perm))
+ return 0;
+
+ dprintk("%s: dst: prio: %d, perm: %x, new: prio: %d, perm: %d.\n",
+ __func__, dst->state.ctl.prio, dst->state.ctl.perm,
+ new->state.ctl.prio, new->state.ctl.perm);
+ dst->state.ctl.prio = new->state.ctl.prio;
+ dst->state.ctl.perm = new->state.ctl.perm;
+
+ list_del_init(&dst->config_entry);
+ pohmelfs_insert_config_entry(psb, dst);
+ return 0;
+}
+
+/*
+ * pohmelfs_copy_config() is used to copy new state configs from the
+ * config group (controlled by the netlink messages) into the superblock.
+ * This happens either at startup time where no transactions can access
+ * the list of the configs (and thus list of the network states), or at
+ * run-time, where it is protected by the psb->state_lock.
+ */
int pohmelfs_copy_config(struct pohmelfs_sb *psb)
{
struct pohmelfs_config_group *g;
err = 0;
list_for_each_entry(dst, &psb->state_list, config_entry) {
if (pohmelfs_config_eql(&dst->state.ctl, &c->state.ctl)) {
- err = -EEXIST;
+ err = pohmelfs_move_config_entry(psb, dst, c);
+ if (!err)
+ err = -EEXIST;
break;
}
}
memcpy(&dst->state.ctl, &c->state.ctl, sizeof(struct pohmelfs_ctl));
- list_add_tail(&dst->config_entry, &psb->state_list);
+ pohmelfs_insert_config_entry(psb, dst);
err = pohmelfs_state_init_one(psb, dst);
if (err) {
return err;
}
+static int pohmelfs_modify_config(struct pohmelfs_ctl *old, struct pohmelfs_ctl *new)
+{
+ old->perm = new->perm;
+ old->prio = new->prio;
+ return 0;
+}
+
static int pohmelfs_cn_ctl(struct cn_msg *msg, int action)
{
struct pohmelfs_config_group *g;
g->num_entry--;
kfree(c);
goto out_unlock;
+ } else if (action == POHMELFS_FLAGS_MODIFY) {
+ err = pohmelfs_modify_config(sc, ctl);
+ goto out_unlock;
} else {
err = -EEXIST;
goto out_unlock;
}
memcpy(&c->state.ctl, ctl, sizeof(struct pohmelfs_ctl));
g->num_entry++;
+
list_add_tail(&c->config_entry, &g->config_list);
out_unlock:
switch (msg->flags) {
case POHMELFS_FLAGS_ADD:
- err = pohmelfs_cn_ctl(msg, POHMELFS_FLAGS_ADD);
- break;
case POHMELFS_FLAGS_DEL:
- err = pohmelfs_cn_ctl(msg, POHMELFS_FLAGS_DEL);
+ case POHMELFS_FLAGS_MODIFY:
+ err = pohmelfs_cn_ctl(msg, msg->flags);
break;
case POHMELFS_FLAGS_SHOW:
err = pohmelfs_cn_disp(msg);
{
struct inode *inode = &pi->vfs_inode;
struct pohmelfs_sb *psb = POHMELFS_SB(inode->i_sb);
- long ret = msecs_to_jiffies(25000);
+ long ret = psb->wait_on_page_timeout;
int err;
dprintk("%s: dir: %llu, state: %lx: remote_synced: %d.\n",
dprintk("%s: parent: %llu, fpos: %llu, hash: %08lx.\n",
__func__, pi->ino, (u64)file->f_pos,
(unsigned long)file->private_data);
-
+#if 0
err = pohmelfs_data_lock(pi, 0, ~0, POHMELFS_READ_LOCK);
if (err)
return err;
-
+#endif
err = pohmelfs_sync_remote_dir(pi);
if (err)
return err;
need_lock = pohmelfs_need_lock(parent, lock_type);
- err = pohmelfs_data_lock(parent, 0, ~0, lock_type);
- if (err)
- goto out;
-
str.hash = jhash(dentry->d_name.name, dentry->d_name.len, 0);
mutex_lock(&parent->offset_lock);
ino = n->ino;
mutex_unlock(&parent->offset_lock);
- dprintk("%s: 1 ino: %lu, inode: %p, name: '%s', hash: %x, parent_state: %lx.\n",
- __func__, ino, inode, str.name, str.hash, parent->state);
+ dprintk("%s: start ino: %lu, inode: %p, name: '%s', hash: %x, parent_state: %lx, need_lock: %d.\n",
+ __func__, ino, inode, str.name, str.hash, parent->state, need_lock);
if (ino) {
inode = ilookup(dir->i_sb, ino);
goto out;
}
- dprintk("%s: dir: %p, dir_ino: %llu, name: '%s', len: %u, dir_state: %lx, ino: %lu.\n",
+ dprintk("%s: no inode dir: %p, dir_ino: %llu, name: '%s', len: %u, dir_state: %lx, ino: %lu.\n",
__func__, dir, parent->ino,
str.name, str.len, parent->state, ino);
goto out;
}
+ err = pohmelfs_data_lock(parent, 0, ~0, lock_type);
+ if (err)
+ goto out;
+
err = pohmelfs_lookup_single(parent, &str, ino);
if (err)
goto out;
if (ino) {
inode = ilookup(dir->i_sb, ino);
- printk("%s: second lookup ino: %lu, inode: %p, name: '%s', hash: %x.\n",
+ dprintk("%s: second lookup ino: %lu, inode: %p, name: '%s', hash: %x.\n",
__func__, ino, inode, str.name, str.hash);
if (!inode) {
- printk("%s: No inode for ino: %lu, name: '%s', hash: %x.\n",
+ dprintk("%s: No inode for ino: %lu, name: '%s', hash: %x.\n",
__func__, ino, str.name, str.hash);
//return NULL;
return ERR_PTR(-EACCES);
static int pohmelfs_getattr(struct vfsmount *mnt, struct dentry *dentry, struct kstat *stat)
{
struct inode *inode = dentry->d_inode;
+#if 0
struct pohmelfs_inode *pi = POHMELFS_I(inode);
int err;
err = pohmelfs_data_lock(pi, 0, ~0, POHMELFS_READ_LOCK);
if (err)
return err;
-
dprintk("%s: ino: %llu, mode: %o, uid: %u, gid: %u, size: %llu.\n",
__func__, pi->ino, inode->i_mode, inode->i_uid,
inode->i_gid, inode->i_size);
+#endif
generic_fillattr(inode, stat);
return 0;
kfree(psb);
sb->s_fs_info = NULL;
-
- pohmelfs_ftrans_exit();
-}
-
-static int pohmelfs_remount(struct super_block *sb, int *flags, char *data)
-{
- *flags |= MS_RDONLY;
- return 0;
}
static int pohmelfs_statfs(struct dentry *dentry, struct kstatfs *buf)
return 0;
}
-static const struct super_operations pohmelfs_sb_ops = {
- .alloc_inode = pohmelfs_alloc_inode,
- .destroy_inode = pohmelfs_destroy_inode,
- .drop_inode = pohmelfs_drop_inode,
- .write_inode = pohmelfs_write_inode,
- .put_super = pohmelfs_put_super,
- .remount_fs = pohmelfs_remount,
- .statfs = pohmelfs_statfs,
- .show_options = pohmelfs_show_options,
-};
-
enum {
pohmelfs_opt_idx,
+ pohmelfs_opt_crypto_thread_num,
+ pohmelfs_opt_trans_max_pages,
+ pohmelfs_opt_crypto_fail_unsupported,
+
+ /* Remountable options */
pohmelfs_opt_trans_scan_timeout,
pohmelfs_opt_drop_scan_timeout,
pohmelfs_opt_wait_on_page_timeout,
pohmelfs_opt_trans_retries,
- pohmelfs_opt_crypto_thread_num,
- pohmelfs_opt_trans_max_pages,
- pohmelfs_opt_crypto_fail_unsupported,
pohmelfs_opt_mcache_timeout,
};
static struct match_token pohmelfs_tokens[] = {
{pohmelfs_opt_idx, "idx=%u"},
+ {pohmelfs_opt_crypto_thread_num, "crypto_thread_num=%u"},
+ {pohmelfs_opt_trans_max_pages, "trans_max_pages=%u"},
+ {pohmelfs_opt_crypto_fail_unsupported, "crypto_fail_unsupported"},
{pohmelfs_opt_trans_scan_timeout, "trans_scan_timeout=%u"},
{pohmelfs_opt_drop_scan_timeout, "drop_scan_timeout=%u"},
{pohmelfs_opt_wait_on_page_timeout, "wait_on_page_timeout=%u"},
{pohmelfs_opt_trans_retries, "trans_retries=%u"},
- {pohmelfs_opt_crypto_thread_num, "crypto_thread_num=%u"},
- {pohmelfs_opt_trans_max_pages, "trans_max_pages=%u"},
- {pohmelfs_opt_crypto_fail_unsupported, "crypto_fail_unsupported"},
{pohmelfs_opt_mcache_timeout, "mcache_timeout=%u"},
};
-static int pohmelfs_parse_options(char *options, struct pohmelfs_sb *psb)
+static int pohmelfs_parse_options(char *options, struct pohmelfs_sb *psb, int remount)
{
char *p;
substring_t args[MAX_OPT_ARGS];
if (err)
return err;
+ if (remount && token <= pohmelfs_opt_crypto_fail_unsupported)
+ continue;
+
switch (token) {
case pohmelfs_opt_idx:
psb->idx = option;
return 0;
}
+static int pohmelfs_remount(struct super_block *sb, int *flags, char *data)
+{
+ int err;
+ struct pohmelfs_sb *psb = POHMELFS_SB(sb);
+ unsigned long old_sb_flags = sb->s_flags;
+
+ err = pohmelfs_parse_options(data, psb, 1);
+ if (err)
+ goto err_out_restore;
+
+ if (!(*flags & MS_RDONLY))
+ sb->s_flags &= ~MS_RDONLY;
+ return 0;
+
+err_out_restore:
+ sb->s_flags = old_sb_flags;
+ return err;
+}
+
static void pohmelfs_flush_inode(struct pohmelfs_inode *pi, unsigned int count)
{
struct inode *inode = &pi->vfs_inode;
return err;
}
+static int pohmelfs_show_stats(struct seq_file *m, struct vfsmount *mnt)
+{
+ struct netfs_state *st;
+ struct pohmelfs_ctl *ctl;
+ struct pohmelfs_sb *psb = POHMELFS_SB(mnt->mnt_sb);
+ struct pohmelfs_config *c;
+
+ mutex_lock(&psb->state_lock);
+
+ seq_printf(m, "\nidx addr(:port) socket_type protocol active priority permissions\n");
+
+ list_for_each_entry(c, &psb->state_list, config_entry) {
+ st = &c->state;
+ ctl = &st->ctl;
+
+ seq_printf(m, "%u ", ctl->idx);
+ if (ctl->addr.sa_family == AF_INET) {
+ struct sockaddr_in *sin = (struct sockaddr_in *)&st->ctl.addr;
+ //seq_printf(m, "%pi4:%u", &sin->sin_addr.s_addr, ntohs(sin->sin_port));
+ seq_printf(m, "%u.%u.%u.%u:%u", NIPQUAD(sin->sin_addr.s_addr), ntohs(sin->sin_port));
+ } else if (ctl->addr.sa_family == AF_INET6) {
+ struct sockaddr_in6 *sin = (struct sockaddr_in6 *)&st->ctl.addr;
+ seq_printf(m, "%pi6:%u", &sin->sin6_addr, ntohs(sin->sin6_port));
+ } else {
+ unsigned int i;
+ for (i=0; i<ctl->addrlen; ++i)
+ seq_printf(m, "%02x.", ctl->addr.addr[i]);
+ }
+
+ seq_printf(m, " %u %u %d %u %x\n",
+ ctl->type, ctl->proto,
+ st->socket != NULL,
+ ctl->prio, ctl->perm);
+ }
+ mutex_unlock(&psb->state_lock);
+
+ return 0;
+}
+
+static const struct super_operations pohmelfs_sb_ops = {
+ .alloc_inode = pohmelfs_alloc_inode,
+ .destroy_inode = pohmelfs_destroy_inode,
+ .drop_inode = pohmelfs_drop_inode,
+ .write_inode = pohmelfs_write_inode,
+ .put_super = pohmelfs_put_super,
+ .remount_fs = pohmelfs_remount,
+ .statfs = pohmelfs_statfs,
+ .show_options = pohmelfs_show_options,
+ .show_stats = pohmelfs_show_stats,
+};
+
/*
* Allocate private superblock and create root dir.
*/
struct pohmelfs_inode *npi;
struct qstr str;
- pohmelfs_ftrans_init();
-
psb = kzalloc(sizeof(struct pohmelfs_sb), GFP_KERNEL);
if (!psb)
goto err_out_exit;
mutex_init(&psb->state_lock);
INIT_LIST_HEAD(&psb->state_list);
- err = pohmelfs_parse_options((char *) data, psb);
+ err = pohmelfs_parse_options((char *) data, psb, 0);
if (err)
goto err_out_free_sb;
err = PTR_ERR(npi);
goto err_out_crypto_exit;
}
+ set_bit(NETFS_INODE_REMOTE_SYNCED, &npi->state);
+ clear_bit(NETFS_INODE_OWNED, &npi->state);
root = &npi->vfs_inode;
mnt);
}
+/*
+ * We need this to sync all inodes earlier, since when writeback
+ * is invoked from the umount/mntput path dcache is already shrunk,
+ * see generic_shutdown_super(), and no inodes can access the path.
+ */
+static void pohmelfs_kill_super(struct super_block *sb)
+{
+ struct writeback_control wbc = {
+ .sync_mode = WB_SYNC_ALL,
+ .range_start = 0,
+ .range_end = LLONG_MAX,
+ .nr_to_write = LONG_MAX,
+ };
+ generic_sync_sb_inodes(sb, &wbc);
+
+ kill_anon_super(sb);
+}
+
static struct file_system_type pohmel_fs_type = {
.owner = THIS_MODULE,
.name = "pohmel",
.get_sb = pohmelfs_get_sb,
- .kill_sb = kill_anon_super,
+ .kill_sb = pohmelfs_kill_super,
};
/*
path_len = err;
err = -ENOMEM;
- t = netfs_trans_alloc(psb, path_len + sizeof(struct netfs_lock) + isize, 0, 0);
+ t = netfs_trans_alloc(psb, path_len + sizeof(struct netfs_lock) + isize,
+ NETFS_TRANS_SINGLE_DST, 0);
if (!t)
goto err_out_exit;
#include "netfs.h"
-static int pohmelfs_ftrans_size = 10240;
-static u32 *pohmelfs_ftrans;
-
-int pohmelfs_ftrans_init(void)
-{
- pohmelfs_ftrans = vmalloc(pohmelfs_ftrans_size * 4);
- if (!pohmelfs_ftrans)
- return -ENOMEM;
-
- return 0;
-}
-
-void pohmelfs_ftrans_exit(void)
-{
- vfree(pohmelfs_ftrans);
-}
-
-void pohmelfs_ftrans_clean(u64 id)
-{
- if (pohmelfs_ftrans) {
- u32 i = id & 0xffffffff;
- int idx = i % pohmelfs_ftrans_size;
-
- pohmelfs_ftrans[idx] = 0;
- }
-}
-
-void pohmelfs_ftrans_update(u64 id)
-{
- if (pohmelfs_ftrans) {
- u32 i = id & 0xffffffff;
- int idx = i % pohmelfs_ftrans_size;
-
- pohmelfs_ftrans[idx] = i;
- }
-}
-
-int pohmelfs_ftrans_check(u64 id)
-{
- if (pohmelfs_ftrans) {
- u32 i = id & 0xffffffff;
- int idx = i % pohmelfs_ftrans_size;
-
- return (pohmelfs_ftrans[idx] == i);
- }
-
- return -1;
-}
-
/*
* Async machinery lives here.
* All commands being sent to server do _not_ require sync reply,
if (err != -EEXIST)
goto err_out_put;
} else {
+ struct dentry *dentry, *alias, *pd;
+
set_bit(NETFS_INODE_REMOTE_SYNCED, &npi->state);
clear_bit(NETFS_INODE_OWNED, &npi->state);
+
+ pd = d_find_alias(&parent->vfs_inode);
+ if (pd) {
+ str.hash = full_name_hash(str.name, str.len);
+ dentry = d_alloc(pd, &str);
+ if (dentry) {
+ alias = d_materialise_unique(dentry, &npi->vfs_inode);
+ if (alias)
+ dput(dentry);
+ }
+
+ dput(dentry);
+ dput(pd);
+ }
}
}
out:
if (dst) {
netfs_trans_remove_nolock(dst, st);
t = dst->trans;
-
- pohmelfs_ftrans_update(cmd->start);
}
mutex_unlock(&st->trans_lock);
if (!t) {
- int check = pohmelfs_ftrans_check(cmd->start);
- printk("%s: failed to find transaction: start: %llu: id: %llu, size: %u, ext: %u, double: %d.\n",
- __func__, cmd->start, cmd->id, cmd->size, cmd->ext, check);
+ printk("%s: failed to find transaction: start: %llu: id: %llu, size: %u, ext: %u.\n",
+ __func__, cmd->start, cmd->id, cmd->size, cmd->ext);
err = -EINVAL;
goto out;
}
POHMELFS_FLAGS_DEL, /* Network state control message for DEL */
POHMELFS_FLAGS_SHOW, /* Network state control message for SHOW */
POHMELFS_FLAGS_CRYPTO, /* Crypto data control message */
+ POHMELFS_FLAGS_MODIFY, /* Network state modification message */
};
/*
unsigned char data[0]; /* Algorithm string, key and IV */
};
+#define POHMELFS_IO_PERM_READ (1<<0)
+#define POHMELFS_IO_PERM_WRITE (1<<1)
+
/*
* Configuration command used to create table of different remote servers.
*/
struct pohmelfs_ctl
{
- unsigned int idx; /* Config index */
- unsigned int type; /* Socket type */
- unsigned int proto; /* Socket protocol */
- unsigned int addrlen; /* Size of the address */
- unsigned short unused; /* Align structure by 4 bytes */
+ __u32 idx; /* Config index */
+ __u32 type; /* Socket type */
+ __u32 proto; /* Socket protocol */
+ __u16 addrlen; /* Size of the address */
+ __u16 perm; /* IO permission */
+ __u16 prio; /* IO priority */
struct saddr addr; /* Remote server address */
};
pohmelfs_mcache_free(psb, m);
}
-int pohmelfs_ftrans_init(void);
-void pohmelfs_ftrans_exit(void);
-void pohmelfs_ftrans_update(u64 id);
-int pohmelfs_ftrans_check(u64 id);
-void pohmelfs_ftrans_clean(u64 id);
-
#endif /* __KERNEL__*/
#endif /* __NETFS_H */
__func__, t, t->gen, t->iovec.iov_len, t->page_num, psb->active_state);
#endif
mutex_lock(&psb->state_lock);
+ list_for_each_entry(c, &psb->state_list, config_entry) {
+ st = &c->state;
- if ((t->flags & NETFS_TRANS_SINGLE_DST) && psb->active_state) {
- st = &psb->active_state->state;
-
- err = -EPIPE;
- if (netfs_state_poll(st) & POLLOUT) {
- err = netfs_trans_push_dst(t, st);
- if (!err) {
- err = netfs_trans_send(t, st);
- if (err) {
- netfs_trans_drop_last(t, st);
- } else {
- pohmelfs_switch_active(psb);
- goto out;
- }
- }
+ if (t->flags & NETFS_TRANS_SINGLE_DST) {
+ if (!(st->ctl.perm & POHMELFS_IO_PERM_READ))
+ continue;
+ } else {
+ if (!(st->ctl.perm & POHMELFS_IO_PERM_WRITE))
+ continue;
}
- pohmelfs_switch_active(psb);
- }
- list_for_each_entry(c, &psb->state_list, config_entry) {
- st = &c->state;
+ if (psb->active_state && (psb->active_state->state.ctl.prio >= st->ctl.prio))
+ st = &psb->active_state->state;
err = netfs_trans_push(t, st);
if (!err && (t->flags & NETFS_TRANS_SINGLE_DST))
break;
}
-out:
+
mutex_unlock(&psb->state_lock);
#if 0
dprintk("%s: fully sent t: %p, gen: %u, size: %u, page_num: %u, err: %d.\n",
t->gen = atomic_inc_return(&psb->trans_gen);
- pohmelfs_ftrans_clean(t->gen);
-
cmd->size = t->iovec.iov_len - sizeof(struct netfs_cmd) +
t->attached_size + t->attached_pages * sizeof(struct netfs_cmd);
cmd->cmd = NETFS_TRANS;
return (-1);
} /* End of rt28xx_open */
+static const struct net_device_ops rt2860_netdev_ops = {
+ .ndo_open = MainVirtualIF_open,
+ .ndo_stop = MainVirtualIF_close,
+ .ndo_do_ioctl = rt28xx_ioctl,
+ .ndo_get_stats = RT28xx_get_ether_stats,
+ .ndo_validate_addr = NULL,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef IKANOS_VX_1X0
+ .ndo_start_xmit = IKANOS_DataFramesTx,
+#else
+ .ndo_start_xmit = rt28xx_send_packets,
+#endif
+};
/* Must not be called for mdev and apdev */
static NDIS_STATUS rt_ieee80211_if_setup(struct net_device *dev, PRTMP_ADAPTER pAd)
//ether_setup(dev);
- dev->hard_start_xmit = rt28xx_send_packets;
-
-#ifdef IKANOS_VX_1X0
- dev->hard_start_xmit = IKANOS_DataFramesTx;
-#endif // IKANOS_VX_1X0 //
#ifdef CONFIG_STA_SUPPORT
#if WIRELESS_EXT >= 12
#if WIRELESS_EXT < 21
dev->get_wireless_stats = rt28xx_get_wireless_stats;
#endif
- dev->get_stats = RT28xx_get_ether_stats;
- dev->open = MainVirtualIF_open; //rt28xx_open;
- dev->stop = MainVirtualIF_close; //rt28xx_close;
dev->priv_flags = INT_MAIN;
- dev->do_ioctl = rt28xx_ioctl;
- dev->validate_addr = NULL;
+ dev->netdev_ops = &rt2860_netdev_ops;
// find available device name
for (i = 0; i < 8; i++)
{
{USB_DEVICE(0x0DF6,0x002B)}, /* Sitecom */ \
{USB_DEVICE(0x0DF6,0x002C)}, /* Sitecom */ \
{USB_DEVICE(0x0DF6,0x002D)}, /* Sitecom */ \
+ {USB_DEVICE(0x0DF6,0x0039)}, /* Sitecom */ \
{USB_DEVICE(0x14B2,0x3C06)}, /* Conceptronic */ \
{USB_DEVICE(0x14B2,0x3C28)}, /* Conceptronic */ \
{USB_DEVICE(0x2019,0xED06)}, /* Planex Communications, Inc. */ \
return (-1);
} /* End of rt28xx_open */
+static const struct net_device_ops rt2870_netdev_ops = {
+ .ndo_open = MainVirtualIF_open,
+ .ndo_stop = MainVirtualIF_close,
+ .ndo_do_ioctl = rt28xx_ioctl,
+ .ndo_get_stats = RT28xx_get_ether_stats,
+ .ndo_validate_addr = NULL,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef IKANOS_VX_1X0
+ .ndo_start_xmit = IKANOS_DataFramesTx,
+#else
+ .ndo_start_xmit = rt28xx_send_packets,
+#endif
+};
/* Must not be called for mdev and apdev */
static NDIS_STATUS rt_ieee80211_if_setup(struct net_device *dev, PRTMP_ADAPTER pAd)
//ether_setup(dev);
- dev->hard_start_xmit = rt28xx_send_packets;
-
-#ifdef IKANOS_VX_1X0
- dev->hard_start_xmit = IKANOS_DataFramesTx;
-#endif // IKANOS_VX_1X0 //
-
// dev->set_multicast_list = ieee80211_set_multicast_list;
// dev->change_mtu = ieee80211_change_mtu;
#ifdef CONFIG_STA_SUPPORT
#if WIRELESS_EXT < 21
dev->get_wireless_stats = rt28xx_get_wireless_stats;
#endif
- dev->get_stats = RT28xx_get_ether_stats;
- dev->open = MainVirtualIF_open; //rt28xx_open;
- dev->stop = MainVirtualIF_close; //rt28xx_close;
// dev->uninit = ieee80211_if_reinit;
// dev->destructor = ieee80211_if_free;
dev->priv_flags = INT_MAIN;
- dev->do_ioctl = rt28xx_ioctl;
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24)
- dev->validate_addr = NULL;
-#endif
+ dev->netdev_ops = &rt2870_netdev_ops;
// find available device name
for (i = 0; i < 8; i++)
{
// OID_SET_HT_PHYMODE SetHT;
// WPDMA_GLO_CFG_STRUC GloCfg;
UINT32 MacCsr0 = 0;
- UINT32 MacValue = 0;
#ifdef RT2870
#ifdef INF_AMAZON_SE
return (-1);
} /* End of rt28xx_open */
+static const struct net_device_ops rt3070_netdev_ops = {
+ .ndo_open = MainVirtualIF_open,
+ .ndo_stop = MainVirtualIF_close,
+ .ndo_do_ioctl = rt28xx_ioctl,
+ .ndo_get_stats = RT28xx_get_ether_stats,
+ .ndo_validate_addr = NULL,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef IKANOS_VX_1X0
+ .ndo_start_xmit = IKANOS_DataFramesTx,
+#else
+ .ndo_start_xmit = rt28xx_send_packets,
+#endif
+};
/* Must not be called for mdev and apdev */
static NDIS_STATUS rt_ieee80211_if_setup(struct net_device *dev, PRTMP_ADAPTER pAd)
//ether_setup(dev);
- dev->hard_start_xmit = rt28xx_send_packets;
-
-#ifdef IKANOS_VX_1X0
- dev->hard_start_xmit = IKANOS_DataFramesTx;
-#endif // IKANOS_VX_1X0 //
-
// dev->set_multicast_list = ieee80211_set_multicast_list;
// dev->change_mtu = ieee80211_change_mtu;
#ifdef CONFIG_STA_SUPPORT
#if WIRELESS_EXT < 21
dev->get_wireless_stats = rt28xx_get_wireless_stats;
#endif
- dev->get_stats = RT28xx_get_ether_stats;
- dev->open = MainVirtualIF_open; //rt28xx_open;
- dev->stop = MainVirtualIF_close; //rt28xx_close;
// dev->uninit = ieee80211_if_reinit;
// dev->destructor = ieee80211_if_free;
dev->priv_flags = INT_MAIN;
- dev->do_ioctl = rt28xx_ioctl;
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24)
- dev->validate_addr = NULL;
-#endif
+ dev->netdev_ops = &rt3070_netdev_ops;
// find available device name
for (i = 0; i < 8; i++)
{
- move firmware loading to request_firmware()
- remove direct memory access of structures
- any remaining sparse and checkpatch.pl warnings
- - any netdev recommended changes
+
+ - use net_device_ops
+ - use dev->stats rather than adapter->stats
+ - don't cast netdev_priv it is already void
+ - use compare_ether_addr
+ - GET RID OF MACROS
+ - work on all architectures
+ - without CONFIG_X86_64 confusion
+ - do 64 bit correctly
+ - don't depend on order of union
+ - get rid of ASSERT(), use BUG() instead but only where necessary
+ looks like most aren't really useful
+ - no new SIOCDEVPRIVATE ioctl allowed
+ - don't use module_param for configuring interrupt mitigation
+ use ethtool instead
+ - reorder code to elminate use of forward declarations
+ - don't keep private linked list of drivers.
+ - remove all the gratiutous debug infrastructure
+ - use PCI_DEVICE()
+ - do ethtool correctly using ethtool_ops
+ - NAPI?
+ - wasted overhead of extra stats
+ - state variables for things that are
+ easily availble and shouldn't be kept in card structure, cardnum, ...
+ slotnumber, events, ...
+ - get rid of slic_spinlock wrapper
+ - volatile == bad design => bad code
+ - locking too fine grained, not designed just throw more locks
+ at problem
+
Please send patches to:
Greg Kroah-Hartman <gregkh@suse.de>
return;
}
+static const struct net_device_ops slic_netdev_ops = {
+ .ndo_open = slic_entry_open,
+ .ndo_stop = slic_entry_halt,
+ .ndo_start_xmit = slic_xmit_start,
+ .ndo_do_ioctl = slic_ioctl,
+ .ndo_set_mac_address = slic_mac_set_address,
+ .ndo_get_stats = slic_get_stats,
+ .ndo_set_multicast_list = slic_mcast_set_list,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
static int __devinit slic_entry_probe(struct pci_dev *pcidev,
const struct pci_device_id *pci_tbl_entry)
{
netdev->base_addr = (unsigned long)adapter->memorybase;
netdev->irq = adapter->irq;
- netdev->open = slic_entry_open;
- netdev->stop = slic_entry_halt;
- netdev->hard_start_xmit = slic_xmit_start;
- netdev->do_ioctl = slic_ioctl;
- netdev->set_mac_address = slic_mac_set_address;
- netdev->get_stats = slic_get_stats;
- netdev->set_multicast_list = slic_mcast_set_list;
+ netdev->netdev_ops = &slic_netdev_ops;
slic_debug_adapter_create(adapter);
}
/* Doesn't already exist. Allocate a structure to hold it */
- mcaddr = kmalloc(sizeof(struct mcast_address), GFP_KERNEL);
+ mcaddr = kmalloc(sizeof(struct mcast_address), GFP_ATOMIC);
if (mcaddr == NULL)
return 1;
}
if (!physcard) {
/* no structure allocated for this physical card yet */
- physcard = kzalloc(sizeof(struct physcard), GFP_KERNEL);
+ physcard = kzalloc(sizeof(struct physcard), GFP_ATOMIC);
ASSERT(physcard);
physcard->next = slic_global.phys_card;
config STLC45XX
tristate "stlc4550/4560 support"
- depends on MAC80211 && WLAN_80211 && SPI_MASTER
+ depends on MAC80211 && WLAN_80211 && SPI_MASTER && GENERIC_HARDIRQS
---help---
This is a driver for stlc4550 and stlc4560 chipsets.
int ret,i;
if (!adapter->intrregistered) {
+ spin_unlock_irqrestore(&sxg_global.driver_lock,
+ sxg_global.flags);
for (i=0; i<adapter->nr_msix_entries; i++) {
ret = request_irq (adapter->msi_entries[i].vector,
sxg_isr,
adapter->netdev->name,
adapter->netdev);
if (ret) {
+ spin_lock_irqsave(&sxg_global.driver_lock,
+ sxg_global.flags);
DBG_ERROR("sxg: MSI-X request_irq (%s) "
"FAILED [%x]\n", adapter->netdev->name,
ret);
}
}
}
+ spin_lock_irqsave(&sxg_global.driver_lock, sxg_global.flags);
adapter->msi_enabled = TRUE;
adapter->intrregistered = 1;
adapter->IntRegistered = TRUE;
return status;
}
+static const struct net_device_ops sxg_netdev_ops = {
+ .ndo_open = sxg_entry_open,
+ .ndo_stop = sxg_entry_halt,
+ .ndo_start_xmit = sxg_send_packets,
+ .ndo_do_ioctl = sxg_ioctl,
+ .ndo_change_mtu = sxg_change_mtu,
+ .ndo_get_stats = sxg_get_stats,
+ .ndo_set_multicast_list = sxg_mcast_set_list,
+ .ndo_validate_addr = eth_validate_addr,
+#if XXXTODO
+ .ndo_set_mac_address = sxg_mac_set_address,
+#else
+ .ndo_set_mac_address = eth_mac_addr,
+#endif
+};
+
static int sxg_entry_probe(struct pci_dev *pcidev,
const struct pci_device_id *pci_tbl_entry)
{
netdev->base_addr = (unsigned long)adapter->base_addr;
netdev->irq = adapter->irq;
- netdev->open = sxg_entry_open;
- netdev->stop = sxg_entry_halt;
- netdev->hard_start_xmit = sxg_send_packets;
- netdev->do_ioctl = sxg_ioctl;
- netdev->change_mtu = sxg_change_mtu;
-#if XXXTODO
- netdev->set_mac_address = sxg_mac_set_address;
-#endif
- netdev->get_stats = sxg_get_stats;
- netdev->set_multicast_list = sxg_mcast_set_list;
+ netdev->netdev_ops = &sxg_netdev_ops;
SET_ETHTOOL_OPS(netdev, &sxg_nic_ethtool_ops);
netdev->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
err = sxg_set_interrupt_capability(adapter);
DBG_ERROR("sxg: %s EXIT\n", __func__);
spin_unlock_irqrestore(&sxg_global.driver_lock, sxg_global.flags);
+ mod_timer(&adapter->watchdog_timer, jiffies);
+
return STATUS_SUCCESS;
}
u64 phys_addr;
unsigned long flags;
unsigned long queue_id=0;
+ int offload_cksum = 0;
SXG_TRACE(TRACE_SXG, SxgTraceBuffer, TRACE_NOISY, "DumbSgl",
pSgl, SxgSgl, 0, 0);
struct iphdr *ip;
ip = ip_hdr(skb);
- if ((ip->protocol == IPPROTO_TCP)&&(DataLength >= sizeof(
+ if (ip->protocol == IPPROTO_TCP)
+ offload_cksum = 1;
+ if (!offload_cksum || !tcp_hdr(skb))
+ queue_id = 0;
+ else if (offload_cksum && (DataLength >= sizeof(
struct tcphdr))){
queue_id = ((ntohs(tcp_hdr(skb)->dest) == ISCSI_PORT) ?
(ntohs (tcp_hdr(skb)->source) &
SXG_LARGE_SEND_QUEUE_MASK));
}
} else if (skb->protocol == htons(ETH_P_IPV6)) {
- if ((ipv6_hdr(skb)->nexthdr == IPPROTO_TCP) && (DataLength >=
- sizeof(struct tcphdr)) ) {
+ if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP)
+ offload_cksum = 1;
+ if (!offload_cksum || !tcp_hdr(skb))
+ queue_id = 0;
+ else if (offload_cksum && (DataLength>=sizeof(struct tcphdr))){
queue_id = ((ntohs(tcp_hdr(skb)->dest) == ISCSI_PORT) ?
(ntohs (tcp_hdr(skb)->source) &
SXG_LARGE_SEND_QUEUE_MASK):
}
SXG_TRACE(TRACE_SXG, SxgTraceBuffer, TRACE_NOISY, "DumbCmd",
XmtCmd, XmtRingInfo->Head, XmtRingInfo->Tail, 0);
- /* Update stats */
- adapter->stats.tx_packets++;
- adapter->stats.tx_bytes += DataLength;
-#if XXXTODO /* Stats stuff */
- if (SXG_MULTICAST_PACKET(EtherHdr)) {
- if (SXG_BROADCAST_PACKET(EtherHdr)) {
- adapter->Stats.DumbXmtBcastPkts++;
- adapter->Stats.DumbXmtBcastBytes += DataLength;
+ memset(XmtCmd, '\0', sizeof(*XmtCmd));
+ XmtCmd->SgEntries = 1;
+ XmtCmd->Flags = 0;
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ /*
+ * We need to set the Checkum in IP header to 0. This is
+ * required by hardware.
+ */
+ if (offload_cksum) {
+ ip_hdr(skb)->check = 0x0;
+ XmtCmd->CsumFlags.Flags |= SXG_SLOWCMD_CSUM_IP;
+ XmtCmd->CsumFlags.Flags |= SXG_SLOWCMD_CSUM_TCP;
+ /*
+ * Dont know if length will require a change in
+ * case of VLAN
+ */
+ XmtCmd->CsumFlags.MacLen = ETH_HLEN;
+ XmtCmd->CsumFlags.IpHl = skb_network_header_len(skb) >>
+ SXG_NW_HDR_LEN_SHIFT;
} else {
- adapter->Stats.DumbXmtMcastPkts++;
- adapter->Stats.DumbXmtMcastBytes += DataLength;
+ if (skb_checksum_help(skb)){
+ printk(KERN_EMERG "Dropped UDP packet for"
+ " incorrect checksum calculation\n");
+ if (XmtCmd)
+ SXG_ABORT_CMD(XmtRingInfo);
+ spin_unlock_irqrestore(&adapter->XmtZeroLock,
+ flags);
+ return STATUS_SUCCESS;
+ }
}
- } else {
- adapter->Stats.DumbXmtUcastPkts++;
- adapter->Stats.DumbXmtUcastBytes += DataLength;
}
-#endif
+
/*
* Fill in the command
* Copy out the first SGE to the command and adjust for offset
(SXG_INVALID_SGL(phys_addr,skb->data_len)))
{
spin_unlock_irqrestore(&adapter->XmtZeroLock, flags);
+ if (XmtCmd)
+ SXG_ABORT_CMD(XmtRingInfo);
/* Silently drop this packet */
printk(KERN_EMERG"Dropped a packet for 64k boundary problem\n");
return STATUS_SUCCESS;
}
- memset(XmtCmd, '\0', sizeof(*XmtCmd));
XmtCmd->Buffer.FirstSgeAddress = phys_addr;
XmtCmd->Buffer.FirstSgeLength = DataLength;
XmtCmd->Buffer.SgeOffset = 0;
XmtCmd->Buffer.TotalLength = DataLength;
- XmtCmd->SgEntries = 1;
- XmtCmd->Flags = 0;
- if (skb->ip_summed == CHECKSUM_PARTIAL) {
- /*
- * We need to set the Checkum in IP header to 0. This is
- * required by hardware.
- */
- ip_hdr(skb)->check = 0x0;
- XmtCmd->CsumFlags.Flags |= SXG_SLOWCMD_CSUM_IP;
- XmtCmd->CsumFlags.Flags |= SXG_SLOWCMD_CSUM_TCP;
- /* Dont know if length will require a change in case of VLAN */
- XmtCmd->CsumFlags.MacLen = ETH_HLEN;
- XmtCmd->CsumFlags.IpHl = skb_network_header_len(skb) >>
- SXG_NW_HDR_LEN_SHIFT;
- }
/*
* Advance transmit cmd descripter by 1.
* NOTE - See comments in SxgTcpOutput where we write
ASSERT((queue_id & ~SXG_LARGE_SEND_QUEUE_MASK) == 0);
WRITE_REG(adapter->UcodeRegs[0].XmtCmd, ((queue_id << 16) | 1), TRUE);
adapter->Stats.XmtQLen++; /* Stats within lock */
+ /* Update stats */
+ adapter->stats.tx_packets++;
+ adapter->stats.tx_bytes += DataLength;
+#if XXXTODO /* Stats stuff */
+ if (SXG_MULTICAST_PACKET(EtherHdr)) {
+ if (SXG_BROADCAST_PACKET(EtherHdr)) {
+ adapter->Stats.DumbXmtBcastPkts++;
+ adapter->Stats.DumbXmtBcastBytes += DataLength;
+ } else {
+ adapter->Stats.DumbXmtMcastPkts++;
+ adapter->Stats.DumbXmtMcastBytes += DataLength;
+ }
+ } else {
+ adapter->Stats.DumbXmtUcastPkts++;
+ adapter->Stats.DumbXmtUcastBytes += DataLength;
+ }
+#endif
+
spin_unlock_irqrestore(&adapter->XmtZeroLock, flags);
SXG_TRACE(TRACE_SXG, SxgTraceBuffer, TRACE_NOISY, "XDumSgl2",
XmtCmd, pSgl, SxgSgl, 0);
tty = tty_port_tty_get(&ATEN2011_port->port->port);
- if (tty && ATEN2011_port->open) {
+ if (tty && ATEN2011_port->open)
/* tell the tty driver that something has changed */
- wake_up_interruptible(&tty->write_wait);
- }
+ tty_wakeup(tty);
/* schedule_work(&ATEN2011_port->port->work); */
tty_kref_put(tty);
status = 0;
status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
- /* force low_latency on so that our tty_push actually forces *
- * the data through,otherwise it is scheduled, and with *
- * high data rates (like with OHCI) data can get lost. */
-
- if (tty)
- tty->low_latency = 1;
/*
* Check to see if we've set up our endpoint info yet
* (can't set it up in ATEN2011_startup as the structures
cflag = tty->termios->c_cflag;
- if (!cflag) {
- dbg("%s %s", __func__, "cflag is NULL");
- return;
- }
-
- /* check that they really want us to change something */
- if (old_termios) {
- if ((cflag == old_termios->c_cflag) &&
- (RELEVANT_IFLAG(tty->termios->c_iflag) ==
- RELEVANT_IFLAG(old_termios->c_iflag))) {
- dbg("%s", "Nothing to change");
- return;
- }
- }
-
- dbg("%s - clfag %08x iflag %08x", __func__,
+ dbg("%s - cflag %08x iflag %08x", __func__,
tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
if (old_termios) {
return 0;
}
+static const struct net_device_ops p80211_netdev_ops = {
+ .ndo_init = p80211knetdev_init,
+ .ndo_open = p80211knetdev_open,
+ .ndo_stop = p80211knetdev_stop,
+ .ndo_get_stats = p80211knetdev_get_stats,
+ .ndo_start_xmit = p80211knetdev_hard_start_xmit,
+ .ndo_set_multicast_list = p80211knetdev_set_multicast_list,
+ .ndo_do_ioctl = p80211knetdev_do_ioctl,
+ .ndo_set_mac_address = p80211knetdev_set_mac_address,
+ .ndo_tx_timeout = p80211knetdev_tx_timeout,
+ .ndo_change_mtu = wlan_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
/*----------------------------------------------------------------
* wlan_setup
*
} else {
wlandev->netdev = dev;
dev->ml_priv = wlandev;
- dev->hard_start_xmit = p80211knetdev_hard_start_xmit;
- dev->get_stats = p80211knetdev_get_stats;
- dev->init = p80211knetdev_init;
- dev->open = p80211knetdev_open;
- dev->stop = p80211knetdev_stop;
+ dev->netdev_ops = &p80211_netdev_ops;
mutex_init(&wlandev->ioctl_lock);
/* block ioctls until fully initialised. Don't forget to call
module_init(hilscher_init_module);
module_exit(hilscher_exit_module);
+MODULE_DEVICE_TABLE(pci, hilscher_pci_ids);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Hans J. Koch, Benedikt Spranger");
iface = &intf->altsetting[0];
ep = &iface->endpoint[0].desc;
- if (!usb_endpoint_is_int_in(ep)) {
+ if (!ep || !usb_endpoint_is_int_in(ep)) {
rv = -EINVAL;
goto err;
}
ret = checkintf(ps, ret);
if (ret)
return ret;
- usb_settoggle(ps->dev, ep & 0xf, !(ep & USB_DIR_IN), 0);
+ usb_reset_endpoint(ps->dev, ep);
return 0;
}
hcd->driver->endpoint_disable(hcd, ep);
}
+/**
+ * usb_hcd_reset_endpoint - reset host endpoint state
+ * @udev: USB device.
+ * @ep: the endpoint to reset.
+ *
+ * Resets any host endpoint state such as the toggle bit, sequence
+ * number and current window.
+ */
+void usb_hcd_reset_endpoint(struct usb_device *udev,
+ struct usb_host_endpoint *ep)
+{
+ struct usb_hcd *hcd = bus_to_hcd(udev->bus);
+
+ if (hcd->driver->endpoint_reset)
+ hcd->driver->endpoint_reset(hcd, ep);
+ else {
+ int epnum = usb_endpoint_num(&ep->desc);
+ int is_out = usb_endpoint_dir_out(&ep->desc);
+ int is_control = usb_endpoint_xfer_control(&ep->desc);
+
+ usb_settoggle(udev, epnum, is_out, 0);
+ if (is_control)
+ usb_settoggle(udev, epnum, !is_out, 0);
+ }
+}
+
/* Protect against drivers that try to unlink URBs after the device
* is gone, by waiting until all unlinks for @udev are finished.
* Since we don't currently track URBs by device, simply wait until
void (*endpoint_disable)(struct usb_hcd *hcd,
struct usb_host_endpoint *ep);
+ /* (optional) reset any endpoint state such as sequence number
+ and current window */
+ void (*endpoint_reset)(struct usb_hcd *hcd,
+ struct usb_host_endpoint *ep);
+
/* root hub support */
int (*hub_status_data) (struct usb_hcd *hcd, char *buf);
int (*hub_control) (struct usb_hcd *hcd,
struct usb_host_endpoint *ep);
extern void usb_hcd_disable_endpoint(struct usb_device *udev,
struct usb_host_endpoint *ep);
+extern void usb_hcd_reset_endpoint(struct usb_device *udev,
+ struct usb_host_endpoint *ep);
extern void usb_hcd_synchronize_unlinks(struct usb_device *udev);
extern int usb_hcd_get_frame_number(struct usb_device *udev);
extern void usb_hc_died(struct usb_hcd *hcd);
extern void usb_hcd_poll_rh_status(struct usb_hcd *hcd);
+/* The D0/D1 toggle bits ... USE WITH CAUTION (they're almost hcd-internal) */
+#define usb_gettoggle(dev, ep, out) (((dev)->toggle[out] >> (ep)) & 1)
+#define usb_dotoggle(dev, ep, out) ((dev)->toggle[out] ^= (1 << (ep)))
+#define usb_settoggle(dev, ep, out, bit) \
+ ((dev)->toggle[out] = ((dev)->toggle[out] & ~(1 << (ep))) | \
+ ((bit) << (ep)))
+
/* -------------------------------------------------------------------------- */
/* Enumeration is only for the hub driver, or HCD virtual root hubs */
* the copy in usb-storage, for as long as we need two copies.
*/
- /* toggle was reset by the clear */
- usb_settoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe), 0);
+ usb_reset_endpoint(dev, endp);
return 0;
}
}
/**
+ * usb_reset_endpoint - Reset an endpoint's state.
+ * @dev: the device whose endpoint is to be reset
+ * @epaddr: the endpoint's address. Endpoint number for output,
+ * endpoint number + USB_DIR_IN for input
+ *
+ * Resets any host-side endpoint state such as the toggle bit,
+ * sequence number or current window.
+ */
+void usb_reset_endpoint(struct usb_device *dev, unsigned int epaddr)
+{
+ unsigned int epnum = epaddr & USB_ENDPOINT_NUMBER_MASK;
+ struct usb_host_endpoint *ep;
+
+ if (usb_endpoint_out(epaddr))
+ ep = dev->ep_out[epnum];
+ else
+ ep = dev->ep_in[epnum];
+ if (ep)
+ usb_hcd_reset_endpoint(dev, ep);
+}
+EXPORT_SYMBOL_GPL(usb_reset_endpoint);
+
+
+/**
* usb_disable_interface -- Disable all endpoints for an interface
* @dev: the device whose interface is being disabled
* @intf: pointer to the interface descriptor
usb_disable_endpoint(dev, i, true);
usb_disable_endpoint(dev, i + USB_DIR_IN, true);
}
- dev->toggle[0] = dev->toggle[1] = 0;
/* getting rid of interfaces will disconnect
* any drivers bound to them (a key side effect)
* usb_enable_endpoint - Enable an endpoint for USB communications
* @dev: the device whose interface is being enabled
* @ep: the endpoint
- * @reset_toggle: flag to set the endpoint's toggle back to 0
+ * @reset_ep: flag to reset the endpoint state
*
- * Resets the endpoint toggle if asked, and sets dev->ep_{in,out} pointers.
+ * Resets the endpoint state if asked, and sets dev->ep_{in,out} pointers.
* For control endpoints, both the input and output sides are handled.
*/
void usb_enable_endpoint(struct usb_device *dev, struct usb_host_endpoint *ep,
- bool reset_toggle)
+ bool reset_ep)
{
int epnum = usb_endpoint_num(&ep->desc);
int is_out = usb_endpoint_dir_out(&ep->desc);
int is_control = usb_endpoint_xfer_control(&ep->desc);
- if (is_out || is_control) {
- if (reset_toggle)
- usb_settoggle(dev, epnum, 1, 0);
+ if (reset_ep)
+ usb_hcd_reset_endpoint(dev, ep);
+ if (is_out || is_control)
dev->ep_out[epnum] = ep;
- }
- if (!is_out || is_control) {
- if (reset_toggle)
- usb_settoggle(dev, epnum, 0, 0);
+ if (!is_out || is_control)
dev->ep_in[epnum] = ep;
- }
ep->enabled = 1;
}
* usb_enable_interface - Enable all the endpoints for an interface
* @dev: the device whose interface is being enabled
* @intf: pointer to the interface descriptor
- * @reset_toggles: flag to set the endpoints' toggles back to 0
+ * @reset_eps: flag to reset the endpoints' state
*
* Enables all the endpoints for the interface's current altsetting.
*/
void usb_enable_interface(struct usb_device *dev,
- struct usb_interface *intf, bool reset_toggles)
+ struct usb_interface *intf, bool reset_eps)
{
struct usb_host_interface *alt = intf->cur_altsetting;
int i;
for (i = 0; i < alt->desc.bNumEndpoints; ++i)
- usb_enable_endpoint(dev, &alt->endpoint[i], reset_toggles);
+ usb_enable_endpoint(dev, &alt->endpoint[i], reset_eps);
}
/**
* This issues a standard SET_CONFIGURATION request to the device using
* the current configuration. The effect is to reset most USB-related
* state in the device, including interface altsettings (reset to zero),
- * endpoint halts (cleared), and data toggle (only for bulk and interrupt
+ * endpoint halts (cleared), and endpoint state (only for bulk and interrupt
* endpoints). Other usbcore state is unchanged, including bindings of
* usb device drivers to interfaces.
*
* (multi-interface) devices. Instead, the driver for each interface may
* use usb_set_interface() on the interfaces it claims. Be careful though;
* some devices don't support the SET_INTERFACE request, and others won't
- * reset all the interface state (notably data toggles). Resetting the whole
+ * reset all the interface state (notably endpoint state). Resetting the whole
* configuration would affect other drivers' interfaces.
*
* The caller must own the device lock.
if (retval < 0)
return retval;
- dev->toggle[0] = dev->toggle[1] = 0;
-
/* re-init hc/hcd interface/endpoint state */
for (i = 0; i < config->desc.bNumInterfaces; i++) {
struct usb_interface *intf = config->interface[i];
dev->ep0.desc.bLength = USB_DT_ENDPOINT_SIZE;
dev->ep0.desc.bDescriptorType = USB_DT_ENDPOINT;
/* ep0 maxpacket comes later, from device descriptor */
- usb_enable_endpoint(dev, &dev->ep0, true);
+ usb_enable_endpoint(dev, &dev->ep0, false);
dev->can_submit = 1;
/* Save readable and stable topology id, distinguishing devices
strlcpy(p->bus_info, dev_name(&dev->gadget->dev), sizeof p->bus_info);
}
-static u32 eth_get_link(struct net_device *net)
-{
- struct eth_dev *dev = netdev_priv(net);
- return dev->gadget->speed != USB_SPEED_UNKNOWN;
-}
-
/* REVISIT can also support:
* - WOL (by tracking suspends and issuing remote wakeup)
* - msglevel (implies updated messaging)
static struct ethtool_ops ops = {
.get_drvinfo = eth_get_drvinfo,
- .get_link = eth_get_link
+ .get_link = ethtool_op_get_link,
};
static void defer_kevent(struct eth_dev *dev, int flag)
process_inactive_qtd(whc, qset, td);
}
- update |= qset_add_qtds(whc, qset);
+ if (!qset->remove)
+ update |= qset_add_qtds(whc, qset);
done:
/*
spin_lock_irqsave(&whc->lock, flags);
+ err = usb_hcd_link_urb_to_ep(&whc->wusbhc.usb_hcd, urb);
+ if (err < 0) {
+ spin_unlock_irqrestore(&whc->lock, flags);
+ return err;
+ }
+
qset = get_qset(whc, urb, GFP_ATOMIC);
if (qset == NULL)
err = -ENOMEM;
else
err = qset_add_urb(whc, qset, urb, GFP_ATOMIC);
if (!err) {
- usb_hcd_link_urb_to_ep(&whc->wusbhc.usb_hcd, urb);
if (!qset->in_sw_list)
asl_qset_insert_begin(whc, qset);
- }
+ } else
+ usb_hcd_unlink_urb_from_ep(&whc->wusbhc.usb_hcd, urb);
spin_unlock_irqrestore(&whc->lock, flags);
if (!err)
queue_work(whc->workqueue, &whc->async_work);
- return 0;
+ return err;
}
/**
}
}
+static void whc_endpoint_reset(struct usb_hcd *usb_hcd,
+ struct usb_host_endpoint *ep)
+{
+ struct wusbhc *wusbhc = usb_hcd_to_wusbhc(usb_hcd);
+ struct whc *whc = wusbhc_to_whc(wusbhc);
+ struct whc_qset *qset;
+
+ qset = ep->hcpriv;
+ if (qset) {
+ qset->remove = 1;
+
+ if (usb_endpoint_xfer_bulk(&ep->desc)
+ || usb_endpoint_xfer_control(&ep->desc))
+ queue_work(whc->workqueue, &whc->async_work);
+ else
+ queue_work(whc->workqueue, &whc->periodic_work);
+
+ qset_reset(whc, qset);
+ }
+}
+
+
static struct hc_driver whc_hc_driver = {
.description = "whci-hcd",
.product_desc = "Wireless host controller",
.urb_enqueue = whc_urb_enqueue,
.urb_dequeue = whc_urb_dequeue,
.endpoint_disable = whc_endpoint_disable,
+ .endpoint_reset = whc_endpoint_reset,
.hub_status_data = wusbhc_rh_status_data,
.hub_control = wusbhc_rh_control,
process_inactive_qtd(whc, qset, td);
}
- update |= qset_add_qtds(whc, qset);
+ if (!qset->remove)
+ update |= qset_add_qtds(whc, qset);
done:
/*
spin_lock_irqsave(&whc->lock, flags);
+ err = usb_hcd_link_urb_to_ep(&whc->wusbhc.usb_hcd, urb);
+ if (err < 0) {
+ spin_unlock_irqrestore(&whc->lock, flags);
+ return err;
+ }
+
qset = get_qset(whc, urb, GFP_ATOMIC);
if (qset == NULL)
err = -ENOMEM;
else
err = qset_add_urb(whc, qset, urb, GFP_ATOMIC);
if (!err) {
- usb_hcd_link_urb_to_ep(&whc->wusbhc.usb_hcd, urb);
if (!qset->in_sw_list)
qset_insert_in_sw_list(whc, qset);
- }
+ } else
+ usb_hcd_unlink_urb_from_ep(&whc->wusbhc.usb_hcd, urb);
spin_unlock_irqrestore(&whc->lock, flags);
if (!err)
queue_work(whc->workqueue, &whc->periodic_work);
- return 0;
+ return err;
}
/**
qset_delete(whc, qset);
}
-
/**
* pzl_init - initialize the periodic zone list
* @whc: the WHCI host controller
QH_INFO3_TX_RATE_53_3
| QH_INFO3_TX_PWR(0) /* 0 == max power */
);
+
+ qset->qh.cur_window = cpu_to_le32((1 << qset->max_burst) - 1);
}
/**
* qset_clear - clear fields in a qset so it may be reinserted into a
- * schedule
+ * schedule.
+ *
+ * The sequence number and current window are not cleared (see
+ * qset_reset()).
*/
void qset_clear(struct whc *whc, struct whc_qset *qset)
{
qset->remove = 0;
qset->qh.link = cpu_to_le32(QH_LINK_NTDS(8) | QH_LINK_T);
- qset->qh.status = cpu_to_le16(QH_STATUS_ICUR(qset->td_start));
+ qset->qh.status = qset->qh.status & QH_STATUS_SEQ_MASK;
qset->qh.err_count = 0;
- qset->qh.cur_window = cpu_to_le32((1 << qset->max_burst) - 1);
qset->qh.scratch[0] = 0;
qset->qh.scratch[1] = 0;
qset->qh.scratch[2] = 0;
}
/**
+ * qset_reset - reset endpoint state in a qset.
+ *
+ * Clears the sequence number and current window. This qset must not
+ * be in the ASL or PZL.
+ */
+void qset_reset(struct whc *whc, struct whc_qset *qset)
+{
+ wait_for_completion(&qset->remove_complete);
+
+ qset->qh.status &= ~QH_STATUS_SEQ_MASK;
+ qset->qh.cur_window = cpu_to_le32((1 << qset->max_burst) - 1);
+}
+
+/**
* get_qset - get the qset for an async endpoint
*
* A new qset is created if one does not already exist.
struct whc_qset *get_qset(struct whc *whc, struct urb *urb, gfp_t mem_flags);
void qset_delete(struct whc *whc, struct whc_qset *qset);
void qset_clear(struct whc *whc, struct whc_qset *qset);
+void qset_reset(struct whc *whc, struct whc_qset *qset);
int qset_add_urb(struct whc *whc, struct whc_qset *qset, struct urb *urb,
gfp_t mem_flags);
void qset_free_std(struct whc *whc, struct whc_std *std);
#define QH_STATUS_FLOW_CTRL (1 << 15)
#define QH_STATUS_ICUR(i) ((i) << 5)
#define QH_STATUS_TO_ICUR(s) (((s) >> 5) & 0x7)
+#define QH_STATUS_SEQ_MASK 0x1f
/**
* usb_pipe_to_qh_type - USB core pipe type to QH transfer type
* trigger the "send a ZLP?" confusion.
*/
rndis = (maxpacket & 0x3f) == 0
+ && length > maxpacket
&& length < 0xffff
&& (length % maxpacket) != 0;
hw_ep = tx_ch->hw_ep;
- /* Peripheral role never repurposes the
- * endpoint, so immediate completion is
- * safe. Host role waits for the fifo
- * to empty (TXPKTRDY irq) before going
- * to the next queued bulk transfer.
- */
- if (is_host_active(cppi->musb)) {
-#if 0
- /* WORKAROUND because we may
- * not always get TXKPTRDY ...
- */
- int csr;
-
- csr = musb_readw(hw_ep->regs,
- MUSB_TXCSR);
- if (csr & MUSB_TXCSR_TXPKTRDY)
-#endif
- completed = false;
- }
- if (completed)
- musb_dma_completion(musb, index + 1, 1);
+ musb_dma_completion(musb, index + 1, 1);
} else {
/* Bigger transfer than we could fit in
return 0;
}
-static int musb_resume(struct platform_device *pdev)
+static int musb_resume_early(struct platform_device *pdev)
{
- unsigned long flags;
struct musb *musb = dev_to_musb(&pdev->dev);
if (!musb->clock)
return 0;
- spin_lock_irqsave(&musb->lock, flags);
-
if (musb->set_clock)
musb->set_clock(musb->clock, 1);
else
clk_enable(musb->clock);
/* for static cmos like DaVinci, register values were preserved
- * unless for some reason the whole soc powered down and we're
- * not treating that as a whole-system restart (e.g. swsusp)
+ * unless for some reason the whole soc powered down or the USB
+ * module got reset through the PSC (vs just being disabled).
*/
- spin_unlock_irqrestore(&musb->lock, flags);
return 0;
}
.remove = __devexit_p(musb_remove),
.shutdown = musb_shutdown,
.suspend = musb_suspend,
- .resume = musb_resume,
+ .resume_early = musb_resume_early,
};
/*-------------------------------------------------------------------------*/
if (is_dma_capable() && ep->dma) {
struct dma_controller *c = ep->musb->dma_controller;
int value;
+
if (ep->is_in) {
+ /*
+ * The programming guide says that we must not clear
+ * the DMAMODE bit before DMAENAB, so we only
+ * clear it in the second write...
+ */
musb_writew(epio, MUSB_TXCSR,
- 0 | MUSB_TXCSR_FLUSHFIFO);
+ MUSB_TXCSR_DMAMODE | MUSB_TXCSR_FLUSHFIFO);
musb_writew(epio, MUSB_TXCSR,
0 | MUSB_TXCSR_FLUSHFIFO);
} else {
| IN token(s) are recd from Host.
| -> DMA interrupt on completion
| calls TxAvail.
- | -> stop DMA, ~DmaEenab,
+ | -> stop DMA, ~DMAENAB,
| -> set TxPktRdy for last short pkt or zlp
| -> Complete Request
| -> Continue next request (call txstate)
request->dma, request_size);
if (use_dma) {
if (musb_ep->dma->desired_mode == 0) {
- /* ASSERT: DMAENAB is clear */
- csr &= ~(MUSB_TXCSR_AUTOSET |
- MUSB_TXCSR_DMAMODE);
+ /*
+ * We must not clear the DMAMODE bit
+ * before the DMAENAB bit -- and the
+ * latter doesn't always get cleared
+ * before we get here...
+ */
+ csr &= ~(MUSB_TXCSR_AUTOSET
+ | MUSB_TXCSR_DMAENAB);
+ musb_writew(epio, MUSB_TXCSR, csr
+ | MUSB_TXCSR_P_WZC_BITS);
+ csr &= ~MUSB_TXCSR_DMAMODE;
csr |= (MUSB_TXCSR_DMAENAB |
MUSB_TXCSR_MODE);
/* against programming guide */
#elif defined(CONFIG_USB_TI_CPPI_DMA)
/* program endpoint CSR first, then setup DMA */
- csr &= ~(MUSB_TXCSR_AUTOSET
- | MUSB_TXCSR_DMAMODE
- | MUSB_TXCSR_P_UNDERRUN
- | MUSB_TXCSR_TXPKTRDY);
+ csr &= ~(MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_TXPKTRDY);
csr |= MUSB_TXCSR_MODE | MUSB_TXCSR_DMAENAB;
musb_writew(epio, MUSB_TXCSR,
(MUSB_TXCSR_P_WZC_BITS & ~MUSB_TXCSR_P_UNDERRUN)
if (!use_dma) {
c->channel_release(musb_ep->dma);
musb_ep->dma = NULL;
- /* ASSERT: DMAENAB clear */
- csr &= ~(MUSB_TXCSR_DMAMODE | MUSB_TXCSR_MODE);
+ csr &= ~MUSB_TXCSR_DMAENAB;
+ musb_writew(epio, MUSB_TXCSR, csr);
/* invariant: prequest->buf is non-null */
}
#elif defined(CONFIG_USB_TUSB_OMAP_DMA)
* Copyright 2005 Mentor Graphics Corporation
* Copyright (C) 2005-2006 by Texas Instruments
* Copyright (C) 2006-2007 Nokia Corporation
+ * Copyright (C) 2008-2009 MontaVista Software, Inc. <source@mvista.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
static void musb_ep_program(struct musb *musb, u8 epnum,
- struct urb *urb, unsigned int nOut,
- u8 *buf, u32 len);
+ struct urb *urb, int is_out,
+ u8 *buf, u32 offset, u32 len);
/*
* Clear TX fifo. Needed to avoid BABBLE errors.
}
}
+static void musb_h_ep0_flush_fifo(struct musb_hw_ep *ep)
+{
+ void __iomem *epio = ep->regs;
+ u16 csr;
+ int retries = 5;
+
+ /* scrub any data left in the fifo */
+ do {
+ csr = musb_readw(epio, MUSB_TXCSR);
+ if (!(csr & (MUSB_CSR0_TXPKTRDY | MUSB_CSR0_RXPKTRDY)))
+ break;
+ musb_writew(epio, MUSB_TXCSR, MUSB_CSR0_FLUSHFIFO);
+ csr = musb_readw(epio, MUSB_TXCSR);
+ udelay(10);
+ } while (--retries);
+
+ WARN(!retries, "Could not flush host TX%d fifo: csr: %04x\n",
+ ep->epnum, csr);
+
+ /* and reset for the next transfer */
+ musb_writew(epio, MUSB_TXCSR, 0);
+}
+
/*
* Start transmit. Caller is responsible for locking shared resources.
* musb must be locked.
}
-static inline void cppi_host_txdma_start(struct musb_hw_ep *ep)
+static inline void musb_h_tx_dma_start(struct musb_hw_ep *ep)
{
u16 txcsr;
/* NOTE: no locks here; caller should lock and select EP */
txcsr = musb_readw(ep->regs, MUSB_TXCSR);
txcsr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_H_WZC_BITS;
+ if (is_cppi_enabled())
+ txcsr |= MUSB_TXCSR_DMAMODE;
musb_writew(ep->regs, MUSB_TXCSR, txcsr);
}
{
u16 frame;
u32 len;
- void *buf;
void __iomem *mbase = musb->mregs;
struct urb *urb = next_urb(qh);
+ void *buf = urb->transfer_buffer;
+ u32 offset = 0;
struct musb_hw_ep *hw_ep = qh->hw_ep;
unsigned pipe = urb->pipe;
u8 address = usb_pipedevice(pipe);
case USB_ENDPOINT_XFER_ISOC:
qh->iso_idx = 0;
qh->frame = 0;
- buf = urb->transfer_buffer + urb->iso_frame_desc[0].offset;
+ offset = urb->iso_frame_desc[0].offset;
len = urb->iso_frame_desc[0].length;
break;
default: /* bulk, interrupt */
case USB_ENDPOINT_XFER_ISOC: s = "-iso"; break;
default: s = "-intr"; break;
}; s; }),
- epnum, buf, len);
+ epnum, buf + offset, len);
/* Configure endpoint */
if (is_in || hw_ep->is_shared_fifo)
hw_ep->in_qh = qh;
else
hw_ep->out_qh = qh;
- musb_ep_program(musb, epnum, urb, !is_in, buf, len);
+ musb_ep_program(musb, epnum, urb, !is_in, buf, offset, len);
/* transmit may have more work: start it when it is time */
if (is_in)
case USB_ENDPOINT_XFER_ISOC:
case USB_ENDPOINT_XFER_INT:
DBG(3, "check whether there's still time for periodic Tx\n");
- qh->iso_idx = 0;
frame = musb_readw(mbase, MUSB_FRAME);
/* FIXME this doesn't implement that scheduling policy ...
* or handle framecounter wrapping
if (!hw_ep->tx_channel)
musb_h_tx_start(hw_ep);
else if (is_cppi_enabled() || tusb_dma_omap())
- cppi_host_txdma_start(hw_ep);
+ musb_h_tx_dma_start(hw_ep);
}
}
csr = musb_readw(ep->regs, MUSB_TXCSR);
if (csr & MUSB_TXCSR_MODE) {
musb_h_tx_flush_fifo(ep);
+ csr = musb_readw(ep->regs, MUSB_TXCSR);
musb_writew(ep->regs, MUSB_TXCSR,
- MUSB_TXCSR_FRCDATATOG);
+ csr | MUSB_TXCSR_FRCDATATOG);
}
- /* clear mode (and everything else) to enable Rx */
+
+ /*
+ * Clear the MODE bit (and everything else) to enable Rx.
+ * NOTE: we mustn't clear the DMAMODE bit before DMAENAB.
+ */
+ if (csr & MUSB_TXCSR_DMAMODE)
+ musb_writew(ep->regs, MUSB_TXCSR, MUSB_TXCSR_DMAMODE);
musb_writew(ep->regs, MUSB_TXCSR, 0);
/* scrub all previous state, clearing toggle */
ep->rx_reinit = 0;
}
+static bool musb_tx_dma_program(struct dma_controller *dma,
+ struct musb_hw_ep *hw_ep, struct musb_qh *qh,
+ struct urb *urb, u32 offset, u32 length)
+{
+ struct dma_channel *channel = hw_ep->tx_channel;
+ void __iomem *epio = hw_ep->regs;
+ u16 pkt_size = qh->maxpacket;
+ u16 csr;
+ u8 mode;
+
+#ifdef CONFIG_USB_INVENTRA_DMA
+ if (length > channel->max_len)
+ length = channel->max_len;
+
+ csr = musb_readw(epio, MUSB_TXCSR);
+ if (length > pkt_size) {
+ mode = 1;
+ csr |= MUSB_TXCSR_AUTOSET
+ | MUSB_TXCSR_DMAMODE
+ | MUSB_TXCSR_DMAENAB;
+ } else {
+ mode = 0;
+ csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAMODE);
+ csr |= MUSB_TXCSR_DMAENAB; /* against programmer's guide */
+ }
+ channel->desired_mode = mode;
+ musb_writew(epio, MUSB_TXCSR, csr);
+#else
+ if (!is_cppi_enabled() && !tusb_dma_omap())
+ return false;
+
+ channel->actual_len = 0;
+
+ /*
+ * TX uses "RNDIS" mode automatically but needs help
+ * to identify the zero-length-final-packet case.
+ */
+ mode = (urb->transfer_flags & URB_ZERO_PACKET) ? 1 : 0;
+#endif
+
+ qh->segsize = length;
+
+ if (!dma->channel_program(channel, pkt_size, mode,
+ urb->transfer_dma + offset, length)) {
+ dma->channel_release(channel);
+ hw_ep->tx_channel = NULL;
+
+ csr = musb_readw(epio, MUSB_TXCSR);
+ csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAENAB);
+ musb_writew(epio, MUSB_TXCSR, csr | MUSB_TXCSR_H_WZC_BITS);
+ return false;
+ }
+ return true;
+}
/*
* Program an HDRC endpoint as per the given URB
* Context: irqs blocked, controller lock held
*/
static void musb_ep_program(struct musb *musb, u8 epnum,
- struct urb *urb, unsigned int is_out,
- u8 *buf, u32 len)
+ struct urb *urb, int is_out,
+ u8 *buf, u32 offset, u32 len)
{
struct dma_controller *dma_controller;
struct dma_channel *dma_channel;
/* general endpoint setup */
if (epnum) {
- /* ASSERT: TXCSR_DMAENAB was already cleared */
-
/* flush all old state, set default */
musb_h_tx_flush_fifo(hw_ep);
+
+ /*
+ * We must not clear the DMAMODE bit before or in
+ * the same cycle with the DMAENAB bit, so we clear
+ * the latter first...
+ */
csr &= ~(MUSB_TXCSR_H_NAKTIMEOUT
- | MUSB_TXCSR_DMAMODE
+ | MUSB_TXCSR_AUTOSET
+ | MUSB_TXCSR_DMAENAB
| MUSB_TXCSR_FRCDATATOG
| MUSB_TXCSR_H_RXSTALL
| MUSB_TXCSR_H_ERROR
);
csr |= MUSB_TXCSR_MODE;
- if (usb_gettoggle(urb->dev,
- qh->epnum, 1))
+ if (usb_gettoggle(urb->dev, qh->epnum, 1))
csr |= MUSB_TXCSR_H_WR_DATATOGGLE
| MUSB_TXCSR_H_DATATOGGLE;
else
csr |= MUSB_TXCSR_CLRDATATOG;
- /* twice in case of double packet buffering */
musb_writew(epio, MUSB_TXCSR, csr);
/* REVISIT may need to clear FLUSHFIFO ... */
+ csr &= ~MUSB_TXCSR_DMAMODE;
musb_writew(epio, MUSB_TXCSR, csr);
csr = musb_readw(epio, MUSB_TXCSR);
} else {
/* endpoint 0: just flush */
- musb_writew(epio, MUSB_CSR0,
- csr | MUSB_CSR0_FLUSHFIFO);
- musb_writew(epio, MUSB_CSR0,
- csr | MUSB_CSR0_FLUSHFIFO);
+ musb_h_ep0_flush_fifo(hw_ep);
}
/* target addr and (for multipoint) hub addr/port */
else
load_count = min((u32) packet_sz, len);
-#ifdef CONFIG_USB_INVENTRA_DMA
- if (dma_channel) {
-
- /* clear previous state */
- csr = musb_readw(epio, MUSB_TXCSR);
- csr &= ~(MUSB_TXCSR_AUTOSET
- | MUSB_TXCSR_DMAMODE
- | MUSB_TXCSR_DMAENAB);
- csr |= MUSB_TXCSR_MODE;
- musb_writew(epio, MUSB_TXCSR,
- csr | MUSB_TXCSR_MODE);
-
- qh->segsize = min(len, dma_channel->max_len);
-
- if (qh->segsize <= packet_sz)
- dma_channel->desired_mode = 0;
- else
- dma_channel->desired_mode = 1;
-
-
- if (dma_channel->desired_mode == 0) {
- csr &= ~(MUSB_TXCSR_AUTOSET
- | MUSB_TXCSR_DMAMODE);
- csr |= (MUSB_TXCSR_DMAENAB);
- /* against programming guide */
- } else
- csr |= (MUSB_TXCSR_AUTOSET
- | MUSB_TXCSR_DMAENAB
- | MUSB_TXCSR_DMAMODE);
-
- musb_writew(epio, MUSB_TXCSR, csr);
-
- dma_ok = dma_controller->channel_program(
- dma_channel, packet_sz,
- dma_channel->desired_mode,
- urb->transfer_dma,
- qh->segsize);
- if (dma_ok) {
- load_count = 0;
- } else {
- dma_controller->channel_release(dma_channel);
- if (is_out)
- hw_ep->tx_channel = NULL;
- else
- hw_ep->rx_channel = NULL;
- dma_channel = NULL;
- }
- }
-#endif
-
- /* candidate for DMA */
- if ((is_cppi_enabled() || tusb_dma_omap()) && dma_channel) {
-
- /* program endpoint CSRs first, then setup DMA.
- * assume CPPI setup succeeds.
- * defer enabling dma.
- */
- csr = musb_readw(epio, MUSB_TXCSR);
- csr &= ~(MUSB_TXCSR_AUTOSET
- | MUSB_TXCSR_DMAMODE
- | MUSB_TXCSR_DMAENAB);
- csr |= MUSB_TXCSR_MODE;
- musb_writew(epio, MUSB_TXCSR,
- csr | MUSB_TXCSR_MODE);
-
- dma_channel->actual_len = 0L;
- qh->segsize = len;
-
- /* TX uses "rndis" mode automatically, but needs help
- * to identify the zero-length-final-packet case.
- */
- dma_ok = dma_controller->channel_program(
- dma_channel, packet_sz,
- (urb->transfer_flags
- & URB_ZERO_PACKET)
- == URB_ZERO_PACKET,
- urb->transfer_dma,
- qh->segsize);
- if (dma_ok) {
- load_count = 0;
- } else {
- dma_controller->channel_release(dma_channel);
- hw_ep->tx_channel = NULL;
- dma_channel = NULL;
-
- /* REVISIT there's an error path here that
- * needs handling: can't do dma, but
- * there's no pio buffer address...
- */
- }
- }
+ if (dma_channel && musb_tx_dma_program(dma_controller,
+ hw_ep, qh, urb, offset, len))
+ load_count = 0;
if (load_count) {
- /* ASSERT: TXCSR_DMAENAB was already cleared */
-
/* PIO to load FIFO */
qh->segsize = load_count;
musb_write_fifo(hw_ep, load_count, buf);
- csr = musb_readw(epio, MUSB_TXCSR);
- csr &= ~(MUSB_TXCSR_DMAENAB
- | MUSB_TXCSR_DMAMODE
- | MUSB_TXCSR_AUTOSET);
- /* write CSR */
- csr |= MUSB_TXCSR_MODE;
-
- if (epnum)
- musb_writew(epio, MUSB_TXCSR, csr);
}
/* re-enable interrupt */
dma_channel, packet_sz,
!(urb->transfer_flags
& URB_SHORT_NOT_OK),
- urb->transfer_dma,
+ urb->transfer_dma + offset,
qh->segsize);
if (!dma_ok) {
dma_controller->channel_release(
csr &= ~MUSB_CSR0_H_NAKTIMEOUT;
musb_writew(epio, MUSB_CSR0, csr);
} else {
- csr |= MUSB_CSR0_FLUSHFIFO;
- musb_writew(epio, MUSB_CSR0, csr);
- musb_writew(epio, MUSB_CSR0, csr);
- csr &= ~MUSB_CSR0_H_NAKTIMEOUT;
- musb_writew(epio, MUSB_CSR0, csr);
+ musb_h_ep0_flush_fifo(hw_ep);
}
musb_writeb(epio, MUSB_NAKLIMIT0, 0);
* SHOULD NEVER HAPPEN! */
ERR("no URB for end 0\n");
- musb_writew(epio, MUSB_CSR0, MUSB_CSR0_FLUSHFIFO);
- musb_writew(epio, MUSB_CSR0, MUSB_CSR0_FLUSHFIFO);
- musb_writew(epio, MUSB_CSR0, 0);
-
+ musb_h_ep0_flush_fifo(hw_ep);
goto done;
}
int pipe;
bool done = false;
u16 tx_csr;
- size_t wLength = 0;
- u8 *buf = NULL;
+ size_t length = 0;
+ size_t offset = 0;
struct urb *urb;
struct musb_hw_ep *hw_ep = musb->endpoints + epnum;
void __iomem *epio = hw_ep->regs;
/* with CPPI, DMA sometimes triggers "extra" irqs */
if (!urb) {
DBG(4, "extra TX%d ready, csr %04x\n", epnum, tx_csr);
- goto finish;
+ return;
}
pipe = urb->pipe;
musb_writew(epio, MUSB_TXCSR,
MUSB_TXCSR_H_WZC_BITS
| MUSB_TXCSR_TXPKTRDY);
- goto finish;
+ return;
}
if (status) {
/* second cppi case */
if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) {
DBG(4, "extra TX%d ready, csr %04x\n", epnum, tx_csr);
- goto finish;
+ return;
+ }
+
+ if (is_dma_capable() && dma && !status) {
+ /*
+ * DMA has completed. But if we're using DMA mode 1 (multi
+ * packet DMA), we need a terminal TXPKTRDY interrupt before
+ * we can consider this transfer completed, lest we trash
+ * its last packet when writing the next URB's data. So we
+ * switch back to mode 0 to get that interrupt; we'll come
+ * back here once it happens.
+ */
+ if (tx_csr & MUSB_TXCSR_DMAMODE) {
+ /*
+ * We shouldn't clear DMAMODE with DMAENAB set; so
+ * clear them in a safe order. That should be OK
+ * once TXPKTRDY has been set (and I've never seen
+ * it being 0 at this moment -- DMA interrupt latency
+ * is significant) but if it hasn't been then we have
+ * no choice but to stop being polite and ignore the
+ * programmer's guide... :-)
+ *
+ * Note that we must write TXCSR with TXPKTRDY cleared
+ * in order not to re-trigger the packet send (this bit
+ * can't be cleared by CPU), and there's another caveat:
+ * TXPKTRDY may be set shortly and then cleared in the
+ * double-buffered FIFO mode, so we do an extra TXCSR
+ * read for debouncing...
+ */
+ tx_csr &= musb_readw(epio, MUSB_TXCSR);
+ if (tx_csr & MUSB_TXCSR_TXPKTRDY) {
+ tx_csr &= ~(MUSB_TXCSR_DMAENAB |
+ MUSB_TXCSR_TXPKTRDY);
+ musb_writew(epio, MUSB_TXCSR,
+ tx_csr | MUSB_TXCSR_H_WZC_BITS);
+ }
+ tx_csr &= ~(MUSB_TXCSR_DMAMODE |
+ MUSB_TXCSR_TXPKTRDY);
+ musb_writew(epio, MUSB_TXCSR,
+ tx_csr | MUSB_TXCSR_H_WZC_BITS);
+
+ /*
+ * There is no guarantee that we'll get an interrupt
+ * after clearing DMAMODE as we might have done this
+ * too late (after TXPKTRDY was cleared by controller).
+ * Re-read TXCSR as we have spoiled its previous value.
+ */
+ tx_csr = musb_readw(epio, MUSB_TXCSR);
+ }
+ /*
+ * We may get here from a DMA completion or TXPKTRDY interrupt.
+ * In any case, we must check the FIFO status here and bail out
+ * only if the FIFO still has data -- that should prevent the
+ * "missed" TXPKTRDY interrupts and deal with double-buffered
+ * FIFO mode too...
+ */
+ if (tx_csr & (MUSB_TXCSR_FIFONOTEMPTY | MUSB_TXCSR_TXPKTRDY)) {
+ DBG(2, "DMA complete but packet still in FIFO, "
+ "CSR %04x\n", tx_csr);
+ return;
+ }
}
- /* REVISIT this looks wrong... */
if (!status || dma || usb_pipeisoc(pipe)) {
if (dma)
- wLength = dma->actual_len;
+ length = dma->actual_len;
else
- wLength = qh->segsize;
- qh->offset += wLength;
+ length = qh->segsize;
+ qh->offset += length;
if (usb_pipeisoc(pipe)) {
struct usb_iso_packet_descriptor *d;
d = urb->iso_frame_desc + qh->iso_idx;
- d->actual_length = qh->segsize;
+ d->actual_length = length;
+ d->status = status;
if (++qh->iso_idx >= urb->number_of_packets) {
done = true;
} else {
d++;
- buf = urb->transfer_buffer + d->offset;
- wLength = d->length;
+ offset = d->offset;
+ length = d->length;
}
} else if (dma) {
done = true;
& URB_ZERO_PACKET))
done = true;
if (!done) {
- buf = urb->transfer_buffer
- + qh->offset;
- wLength = urb->transfer_buffer_length
- - qh->offset;
+ offset = qh->offset;
+ length = urb->transfer_buffer_length - offset;
}
}
}
urb->status = status;
urb->actual_length = qh->offset;
musb_advance_schedule(musb, urb, hw_ep, USB_DIR_OUT);
+ return;
+ } else if (usb_pipeisoc(pipe) && dma) {
+ if (musb_tx_dma_program(musb->dma_controller, hw_ep, qh, urb,
+ offset, length))
+ return;
+ } else if (tx_csr & MUSB_TXCSR_DMAENAB) {
+ DBG(1, "not complete, but DMA enabled?\n");
+ return;
+ }
- } else if (!(tx_csr & MUSB_TXCSR_DMAENAB)) {
- /* WARN_ON(!buf); */
-
- /* REVISIT: some docs say that when hw_ep->tx_double_buffered,
- * (and presumably, fifo is not half-full) we should write TWO
- * packets before updating TXCSR ... other docs disagree ...
- */
- /* PIO: start next packet in this URB */
- if (wLength > qh->maxpacket)
- wLength = qh->maxpacket;
- musb_write_fifo(hw_ep, wLength, buf);
- qh->segsize = wLength;
-
- musb_ep_select(mbase, epnum);
- musb_writew(epio, MUSB_TXCSR,
- MUSB_TXCSR_H_WZC_BITS | MUSB_TXCSR_TXPKTRDY);
- } else
- DBG(1, "not complete, but dma enabled?\n");
+ /*
+ * PIO: start next packet in this URB.
+ *
+ * REVISIT: some docs say that when hw_ep->tx_double_buffered,
+ * (and presumably, FIFO is not half-full) we should write *two*
+ * packets before updating TXCSR; other docs disagree...
+ */
+ if (length > qh->maxpacket)
+ length = qh->maxpacket;
+ musb_write_fifo(hw_ep, length, urb->transfer_buffer + offset);
+ qh->segsize = length;
-finish:
- return;
+ musb_ep_select(mbase, epnum);
+ musb_writew(epio, MUSB_TXCSR,
+ MUSB_TXCSR_H_WZC_BITS | MUSB_TXCSR_TXPKTRDY);
}
unsigned long flags;
struct musb *musb = hcd_to_musb(hcd);
struct usb_host_endpoint *hep = urb->ep;
- struct musb_qh *qh = hep->hcpriv;
+ struct musb_qh *qh;
struct usb_endpoint_descriptor *epd = &hep->desc;
int ret;
unsigned type_reg;
spin_lock_irqsave(&musb->lock, flags);
ret = usb_hcd_link_urb_to_ep(hcd, urb);
+ qh = ret ? NULL : hep->hcpriv;
+ if (qh)
+ urb->hcpriv = qh;
spin_unlock_irqrestore(&musb->lock, flags);
- if (ret)
- return ret;
/* DMA mapping was already done, if needed, and this urb is on
- * hep->urb_list ... so there's little to do unless hep wasn't
- * yet scheduled onto a live qh.
+ * hep->urb_list now ... so we're done, unless hep wasn't yet
+ * scheduled onto a live qh.
*
* REVISIT best to keep hep->hcpriv valid until the endpoint gets
* disabled, testing for empty qh->ring and avoiding qh setup costs
* except for the first urb queued after a config change.
*/
- if (qh) {
- urb->hcpriv = qh;
- return 0;
- }
+ if (qh || ret)
+ return ret;
/* Allocate and initialize qh, minimizing the work done each time
* hw_ep gets reprogrammed, or with irqs blocked. Then schedule it.
* endpoint's irq status here to avoid bogus irqs.
* clearing that status is platform-specific...
*/
- } else {
+ } else if (ep->epnum) {
musb_h_tx_flush_fifo(ep);
csr = musb_readw(epio, MUSB_TXCSR);
csr &= ~(MUSB_TXCSR_AUTOSET
musb_writew(epio, MUSB_TXCSR, csr);
/* flush cpu writebuffer */
csr = musb_readw(epio, MUSB_TXCSR);
+ } else {
+ musb_h_ep0_flush_fifo(ep);
}
if (status == 0)
musb_advance_schedule(ep->musb, urb, ep, is_in);
void __iomem *mbase = musb_channel->controller->base;
u8 bchannel = musb_channel->idx;
+ int offset;
u16 csr;
if (channel->status == MUSB_DMA_STATUS_BUSY) {
if (musb_channel->transmit) {
-
- csr = musb_readw(mbase,
- MUSB_EP_OFFSET(musb_channel->epnum,
- MUSB_TXCSR));
- csr &= ~(MUSB_TXCSR_AUTOSET |
- MUSB_TXCSR_DMAENAB |
- MUSB_TXCSR_DMAMODE);
- musb_writew(mbase,
- MUSB_EP_OFFSET(musb_channel->epnum, MUSB_TXCSR),
- csr);
+ offset = MUSB_EP_OFFSET(musb_channel->epnum,
+ MUSB_TXCSR);
+
+ /*
+ * The programming guide says that we must clear
+ * the DMAENAB bit before the DMAMODE bit...
+ */
+ csr = musb_readw(mbase, offset);
+ csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAENAB);
+ musb_writew(mbase, offset, csr);
+ csr &= ~MUSB_TXCSR_DMAMODE;
+ musb_writew(mbase, offset, csr);
} else {
- csr = musb_readw(mbase,
- MUSB_EP_OFFSET(musb_channel->epnum,
- MUSB_RXCSR));
+ offset = MUSB_EP_OFFSET(musb_channel->epnum,
+ MUSB_RXCSR);
+
+ csr = musb_readw(mbase, offset);
csr &= ~(MUSB_RXCSR_AUTOCLEAR |
MUSB_RXCSR_DMAENAB |
MUSB_RXCSR_DMAMODE);
- musb_writew(mbase,
- MUSB_EP_OFFSET(musb_channel->epnum, MUSB_RXCSR),
- csr);
+ musb_writew(mbase, offset, csr);
}
musb_writew(mbase,
&& ((channel->desired_mode == 0)
|| (channel->actual_len &
(musb_channel->max_packet_sz - 1)))
- ) {
+ ) {
+ u8 epnum = musb_channel->epnum;
+ int offset = MUSB_EP_OFFSET(epnum,
+ MUSB_TXCSR);
+ u16 txcsr;
+
+ /*
+ * The programming guide says that we
+ * must clear DMAENAB before DMAMODE.
+ */
+ musb_ep_select(mbase, epnum);
+ txcsr = musb_readw(mbase, offset);
+ txcsr &= ~(MUSB_TXCSR_DMAENAB
+ | MUSB_TXCSR_AUTOSET);
+ musb_writew(mbase, offset, txcsr);
/* Send out the packet */
- musb_ep_select(mbase,
- musb_channel->epnum);
- musb_writew(mbase, MUSB_EP_OFFSET(
- musb_channel->epnum,
- MUSB_TXCSR),
- MUSB_TXCSR_TXPKTRDY);
- } else {
- musb_dma_completion(
- musb,
- musb_channel->epnum,
- musb_channel->transmit);
+ txcsr &= ~MUSB_TXCSR_DMAMODE;
+ txcsr |= MUSB_TXCSR_TXPKTRDY;
+ musb_writew(mbase, offset, txcsr);
}
+ musb_dma_completion(musb, musb_channel->epnum,
+ musb_channel->transmit);
}
}
}
{ USB_DEVICE(DE_VID, WHT_PID) },
{ USB_DEVICE(ADI_VID, ADI_GNICE_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(JETI_VID, JETI_SPC1201_PID) },
{ }, /* Optional parameter entry */
{ } /* Terminating entry */
};
#define ADI_GNICE_PID 0xF000
/*
+ * JETI SPECTROMETER SPECBOS 1201
+ * http://www.jeti.com/products/sys/scb/scb1201.php
+ */
+#define JETI_VID 0x0c6c
+#define JETI_SPC1201_PID 0x04b2
+
+/*
* BmRequestType: 1100 0000b
* bRequest: FTDI_E2_READ
* wValue: 0
{ USB_DEVICE(0x05c6, 0x3197) }, /* unknown Motorola phone */
{ USB_DEVICE(0x0c44, 0x0022) }, /* unknown Mororola phone */
{ USB_DEVICE(0x22b8, 0x2a64) }, /* Motorola KRZR K1m */
+ { USB_DEVICE(0x22b8, 0x2c64) }, /* Motorola V950 phone */
{ },
};
MODULE_DEVICE_TABLE(usb, id_table);
#define BENQ_VENDOR_ID 0x04a5
#define BENQ_PRODUCT_H10 0x4068
+#define DLINK_VENDOR_ID 0x1186
+#define DLINK_PRODUCT_DWM_652 0x3e04
+
+
static struct usb_device_id option_ids[] = {
{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COLT) },
{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_RICOLA) },
{ USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628) },
{ USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH) },
{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) },
+ { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) },
{ USB_DEVICE(0x1da5, 0x4515) }, /* BenQ H20 */
{ } /* Terminating entry */
};
{USB_DEVICE(0x05c6, 0x9212)}, /* Acer Gobi Modem Device */
{USB_DEVICE(0x03f0, 0x1f1d)}, /* HP un2400 Gobi Modem Device */
{USB_DEVICE(0x03f0, 0x201d)}, /* HP un2400 Gobi QDL Device */
+ {USB_DEVICE(0x04da, 0x250d)}, /* Panasonic Gobi Modem device */
+ {USB_DEVICE(0x04da, 0x250c)}, /* Panasonic Gobi QDL device */
+ {USB_DEVICE(0x413c, 0x8172)}, /* Dell Gobi Modem device */
+ {USB_DEVICE(0x413c, 0x8171)}, /* Dell Gobi QDL device */
+ {USB_DEVICE(0x1410, 0xa001)}, /* Novatel Gobi Modem device */
+ {USB_DEVICE(0x1410, 0xa008)}, /* Novatel Gobi QDL device */
+ {USB_DEVICE(0x0b05, 0x1776)}, /* Asus Gobi Modem device */
+ {USB_DEVICE(0x0b05, 0x1774)}, /* Asus Gobi QDL device */
+ {USB_DEVICE(0x19d2, 0xfff3)}, /* ONDA Gobi Modem device */
+ {USB_DEVICE(0x19d2, 0xfff2)}, /* ONDA Gobi QDL device */
+ {USB_DEVICE(0x1557, 0x0a80)}, /* OQO Gobi QDL device */
+ {USB_DEVICE(0x05c6, 0x9001)}, /* Generic Gobi Modem device */
+ {USB_DEVICE(0x05c6, 0x9002)}, /* Generic Gobi Modem device */
+ {USB_DEVICE(0x05c6, 0x9202)}, /* Generic Gobi Modem device */
+ {USB_DEVICE(0x05c6, 0x9203)}, /* Generic Gobi Modem device */
+ {USB_DEVICE(0x05c6, 0x9222)}, /* Generic Gobi Modem device */
+ {USB_DEVICE(0x05c6, 0x9008)}, /* Generic Gobi QDL device */
+ {USB_DEVICE(0x05c6, 0x9201)}, /* Generic Gobi QDL device */
+ {USB_DEVICE(0x05c6, 0x9221)}, /* Generic Gobi QDL device */
+ {USB_DEVICE(0x05c6, 0x9231)}, /* Generic Gobi QDL device */
+ {USB_DEVICE(0x1f45, 0x0001)}, /* Unknown Gobi QDL device */
{ } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, id_table);
ifeq ($(CONFIG_USB_LIBUSUAL),)
usb-storage-objs += usual-tables.o
else
- obj-$(CONFIG_USB) += libusual.o usual-tables.o
+ obj-$(CONFIG_USB) += usb-libusual.o
+ usb-libusual-objs := libusual.o usual-tables.o
endif
obj-$(CONFIG_USB_STORAGE_ALAUDA) += ums-alauda.o
USB_ENDPOINT_HALT, endp,
NULL, 0, 3*HZ);
- /* reset the endpoint toggle */
if (result >= 0)
- usb_settoggle(us->pusb_dev, usb_pipeendpoint(pipe),
- usb_pipeout(pipe), 0);
+ usb_reset_endpoint(us->pusb_dev, endp);
US_DEBUGP("%s: result = %d\n", __func__, result);
return result;
US_SC_DEVICE, US_PR_DEVICE, NULL,
US_FL_FIX_INQUIRY | US_FL_FIX_CAPACITY ),
-/* Reported by Rauch Wolke <rauchwolke@gmx.net> */
+/* Reported by Rauch Wolke <rauchwolke@gmx.net>
+ * and augmented by binbin <binbinsh@gmail.com> (Bugzilla #12882)
+ */
UNUSUAL_DEV( 0x07c4, 0xa4a5, 0x0000, 0xffff,
"Simple Tech/Datafab",
"CF+SM Reader",
US_SC_DEVICE, US_PR_DEVICE, NULL,
- US_FL_IGNORE_RESIDUE ),
+ US_FL_IGNORE_RESIDUE | US_FL_MAX_SECTORS_64 ),
/* Casio QV 2x00/3x00/4000/8000 digital still cameras are not conformant
* to the USB storage specification in two ways:
US_SC_DEVICE, US_PR_DEVICE, NULL,
0),
+/* Reported by Pascal Terjan <pterjan@mandriva.com>
+ * Ignore driver CD mode and force into modem mode by default.
+ */
+UNUSUAL_DEV( 0x1186, 0x3e04, 0x0000, 0x0000,
+ "D-Link",
+ "USB Mass Storage",
+ US_SC_DEVICE, US_PR_DEVICE, option_ms_init, 0),
+
/* Reported by Kevin Lloyd <linux@sierrawireless.com>
* Entry is needed for the initializer function override,
* which instructs the device to load as a modem
mutex_lock(&wusbhc->mutex);
wusbhc_devconnect_acked(wusbhc, wusb_dev);
mutex_unlock(&wusbhc->mutex);
+
+ wusb_dev_put(wusb_dev);
}
/*
/* After a device disconnects, change the GTK (see [WUSB]
* section 6.2.11.2). */
- wusbhc_gtk_rekey(wusbhc);
+ if (wusbhc->active)
+ wusbhc_gtk_rekey(wusbhc);
/* The Wireless USB part has forgotten about the device already; now
* khubd's timer will pick up the disconnection and remove the USB
* wusbhc_devconnect_stop - stop managing connected devices
* @wusbhc: the WUSB HC
*
- * Removes the Host Info IE and stops the keep alives.
- *
- * FIXME: should this disconnect all devices?
+ * Disconnects any devices still connected, stops the keep alives and
+ * removes the Host Info IE.
*/
void wusbhc_devconnect_stop(struct wusbhc *wusbhc)
{
- cancel_delayed_work_sync(&wusbhc->keep_alive_timer);
- WARN_ON(!list_empty(&wusbhc->cack_list));
+ int i;
+ mutex_lock(&wusbhc->mutex);
+ for (i = 0; i < wusbhc->ports_max; i++) {
+ if (wusbhc->port[i].wusb_dev)
+ __wusbhc_dev_disconnect(wusbhc, &wusbhc->port[i]);
+ }
+ mutex_unlock(&wusbhc->mutex);
+
+ cancel_delayed_work_sync(&wusbhc->keep_alive_timer);
wusbhc_mmcie_rm(wusbhc, &wusbhc->wuie_host_info->hdr);
kfree(wusbhc->wuie_host_info);
wusbhc->wuie_host_info = NULL;
wusb_trust_timeout_store);
/*
- * Show & store the current WUSB CHID
+ * Show the current WUSB CHID.
*/
static ssize_t wusb_chid_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct wusbhc *wusbhc = usbhc_dev_to_wusbhc(dev);
+ const struct wusb_ckhdid *chid;
ssize_t result = 0;
if (wusbhc->wuie_host_info != NULL)
- result += ckhdid_printf(buf, PAGE_SIZE,
- &wusbhc->wuie_host_info->CHID);
+ chid = &wusbhc->wuie_host_info->CHID;
+ else
+ chid = &wusb_ckhdid_zero;
+
+ result += ckhdid_printf(buf, PAGE_SIZE, chid);
+ result += sprintf(buf + result, "\n");
+
return result;
}
/*
- * Store a new CHID
- *
- * This will (FIXME) trigger many changes.
- *
- * - Send an all zeros CHID and it will stop the controller
- * - Send a non-zero CHID and it will start it
- * (unless it was started, it will just change the CHID,
- * diconnecting all devices first).
+ * Store a new CHID.
*
- * So first we scan the MMC we are sent and then we act on it. We
- * read it in the same format as we print it, an ASCII string of 16
- * hex bytes.
+ * - Write an all zeros CHID and it will stop the controller
+ * - Write a non-zero CHID and it will start it.
*
* See wusbhc_chid_set() for more info.
*/
{
struct wusb_dev *wusb_dev = __wusb_dev_get_by_usb_dev(wusbhc, urb->dev);
- if (status == 0) {
+ if (status == 0 && wusb_dev) {
wusb_dev->entry_ts = jiffies;
- /* wusbhc_devconnect_acked() can't be called from from
+ /* wusbhc_devconnect_acked() can't be called from
atomic context so defer it to a work queue. */
if (!list_empty(&wusb_dev->cack_node))
queue_work(wusbd, &wusb_dev->devconnect_acked_work);
+ else
+ wusb_dev_put(wusb_dev);
}
usb_hcd_giveback_urb(&wusbhc->usb_hcd, urb, status);
try_to_freeze();
wait_event_interruptible(vb->config_change,
(diff = towards_target(vb)) != 0
- || kthread_should_stop());
+ || kthread_should_stop()
+ || freezing(current));
if (diff > 0)
fill_balloon(vb, diff);
else if (diff < 0)
return 0;
}
+#ifdef CONFIG_AFS_FSCACHE
/*
* deal with notification that a page was read from the cache
*/
SetPageUptodate(page);
unlock_page(page);
}
+#endif
/*
* AFS read page from file, directory or symlink
return NULL;
}
+/**
+ * bio_alloc - allocate a bio for I/O
+ * @gfp_mask: the GFP_ mask given to the slab allocator
+ * @nr_iovecs: number of iovecs to pre-allocate
+ *
+ * Description:
+ * bio_alloc will allocate a bio and associated bio_vec array that can hold
+ * at least @nr_iovecs entries. Allocations will be done from the
+ * fs_bio_set. Also see @bio_alloc_bioset.
+ *
+ * If %__GFP_WAIT is set, then bio_alloc will always be able to allocate
+ * a bio. This is due to the mempool guarantees. To make this work, callers
+ * must never allocate more than 1 bio at the time from this pool. Callers
+ * that need to allocate more than 1 bio must always submit the previously
+ * allocate bio for IO before attempting to allocate a new one. Failure to
+ * do so can cause livelocks under memory pressure.
+ *
+ **/
struct bio *bio_alloc(gfp_t gfp_mask, int nr_iovecs)
{
struct bio *bio = bio_alloc_bioset(gfp_mask, nr_iovecs, fs_bio_set);
* Completion handler for block_write_full_page() - pages which are unlocked
* during I/O, and which have PageWriteback cleared upon I/O completion.
*/
-static void end_buffer_async_write(struct buffer_head *bh, int uptodate)
+void end_buffer_async_write(struct buffer_head *bh, int uptodate)
{
char b[BDEVNAME_SIZE];
unsigned long flags;
set_buffer_async_read(bh);
}
-void mark_buffer_async_write(struct buffer_head *bh)
+void mark_buffer_async_write_endio(struct buffer_head *bh,
+ bh_end_io_t *handler)
{
- bh->b_end_io = end_buffer_async_write;
+ bh->b_end_io = handler;
set_buffer_async_write(bh);
}
+
+void mark_buffer_async_write(struct buffer_head *bh)
+{
+ mark_buffer_async_write_endio(bh, end_buffer_async_write);
+}
EXPORT_SYMBOL(mark_buffer_async_write);
return err;
}
-void do_thaw_all(unsigned long unused)
+void do_thaw_all(struct work_struct *work)
{
struct super_block *sb;
char b[BDEVNAME_SIZE];
goto restart;
}
spin_unlock(&sb_lock);
+ kfree(work);
printk(KERN_WARNING "Emergency Thaw complete\n");
}
*/
void emergency_thaw_all(void)
{
- pdflush_operation(do_thaw_all, 0);
+ struct work_struct *work;
+
+ work = kmalloc(sizeof(*work), GFP_ATOMIC);
+ if (work) {
+ INIT_WORK(work, do_thaw_all);
+ schedule_work(work);
+ }
}
/**
* unplugging the device queue.
*/
static int __block_write_full_page(struct inode *inode, struct page *page,
- get_block_t *get_block, struct writeback_control *wbc)
+ get_block_t *get_block, struct writeback_control *wbc,
+ bh_end_io_t *handler)
{
int err;
sector_t block;
continue;
}
if (test_clear_buffer_dirty(bh)) {
- mark_buffer_async_write(bh);
+ mark_buffer_async_write_endio(bh, handler);
} else {
unlock_buffer(bh);
}
if (buffer_mapped(bh) && buffer_dirty(bh) &&
!buffer_delay(bh)) {
lock_buffer(bh);
- mark_buffer_async_write(bh);
+ mark_buffer_async_write_endio(bh, handler);
} else {
/*
* The buffer may have been set dirty during
out:
ret = mpage_writepage(page, get_block, wbc);
if (ret == -EAGAIN)
- ret = __block_write_full_page(inode, page, get_block, wbc);
+ ret = __block_write_full_page(inode, page, get_block, wbc,
+ end_buffer_async_write);
return ret;
}
EXPORT_SYMBOL(nobh_writepage);
/*
* The generic ->writepage function for buffer-backed address_spaces
+ * this form passes in the end_io handler used to finish the IO.
*/
-int block_write_full_page(struct page *page, get_block_t *get_block,
- struct writeback_control *wbc)
+int block_write_full_page_endio(struct page *page, get_block_t *get_block,
+ struct writeback_control *wbc, bh_end_io_t *handler)
{
struct inode * const inode = page->mapping->host;
loff_t i_size = i_size_read(inode);
/* Is the page fully inside i_size? */
if (page->index < end_index)
- return __block_write_full_page(inode, page, get_block, wbc);
+ return __block_write_full_page(inode, page, get_block, wbc,
+ handler);
/* Is the page fully outside i_size? (truncate in progress) */
offset = i_size & (PAGE_CACHE_SIZE-1);
* writes to that region are not written out to the file."
*/
zero_user_segment(page, offset, PAGE_CACHE_SIZE);
- return __block_write_full_page(inode, page, get_block, wbc);
+ return __block_write_full_page(inode, page, get_block, wbc, handler);
}
+/*
+ * The generic ->writepage function for buffer-backed address_spaces
+ */
+int block_write_full_page(struct page *page, get_block_t *get_block,
+ struct writeback_control *wbc)
+{
+ return block_write_full_page_endio(page, get_block, wbc,
+ end_buffer_async_write);
+}
+
+
sector_t generic_block_bmap(struct address_space *mapping, sector_t block,
get_block_t *get_block)
{
EXPORT_SYMBOL(block_sync_page);
EXPORT_SYMBOL(block_truncate_page);
EXPORT_SYMBOL(block_write_full_page);
+EXPORT_SYMBOL(block_write_full_page_endio);
EXPORT_SYMBOL(cont_write_begin);
EXPORT_SYMBOL(end_buffer_read_sync);
EXPORT_SYMBOL(end_buffer_write_sync);
+EXPORT_SYMBOL(end_buffer_async_write);
EXPORT_SYMBOL(file_fsync);
EXPORT_SYMBOL(generic_block_bmap);
EXPORT_SYMBOL(generic_cont_expand_simple);
fails to support it properly, as with Samba server versions prior to 3.3.2)
Fix "redzone overwritten" bug in cifs_put_tcon (CIFSTcon may allocate too
little memory for the "nativeFileSystem" field returned by the server
-during mount).
+during mount). Endian convert inode numbers if necessary (makes it easier
+to compare inode numbers on network files from big endian systems).
Version 1.56
------------
/* attach the data */
memcpy(payload, data, datalen);
- rcu_assign_pointer(key->payload.data, payload);
+ key->payload.data = payload;
ret = 0;
error:
extern struct task_struct *oplockThread; /* remove sparse warning */
struct task_struct *oplockThread = NULL;
/* extern struct task_struct * dnotifyThread; remove sparse warning */
-#ifdef CONFIG_CIFS_EXPERIMENTAL
-static struct task_struct *dnotifyThread = NULL;
-#endif
static const struct super_operations cifs_super_ops;
unsigned int CIFSMaxBufSize = CIFS_MAX_MSGSIZE;
module_param(CIFSMaxBufSize, int, 0);
cifs_inode->clientCanCacheAll = false;
cifs_inode->delete_pending = false;
cifs_inode->vfs_inode.i_blkbits = 14; /* 2**14 = CIFS_MAX_MSGSIZE */
+ cifs_inode->server_eof = 0;
/* Can not set i_flags here - they get immediately overwritten
to zero by the VFS */
return 0;
}
-#ifdef CONFIG_CIFS_EXPERIMENTAL
-static int cifs_dnotify_thread(void *dummyarg)
-{
- struct list_head *tmp;
- struct TCP_Server_Info *server;
-
- do {
- if (try_to_freeze())
- continue;
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(15*HZ);
- /* check if any stuck requests that need
- to be woken up and wakeq so the
- thread can wake up and error out */
- read_lock(&cifs_tcp_ses_lock);
- list_for_each(tmp, &cifs_tcp_ses_list) {
- server = list_entry(tmp, struct TCP_Server_Info,
- tcp_ses_list);
- if (atomic_read(&server->inFlight))
- wake_up_all(&server->response_q);
- }
- read_unlock(&cifs_tcp_ses_lock);
- } while (!kthread_should_stop());
-
- return 0;
-}
-#endif
-
static int __init
init_cifs(void)
{
goto out_unregister_dfs_key_type;
}
-#ifdef CONFIG_CIFS_EXPERIMENTAL
- dnotifyThread = kthread_run(cifs_dnotify_thread, NULL, "cifsdnotifyd");
- if (IS_ERR(dnotifyThread)) {
- rc = PTR_ERR(dnotifyThread);
- cERROR(1, ("error %d create dnotify thread", rc));
- goto out_stop_oplock_thread;
- }
-#endif
-
return 0;
-#ifdef CONFIG_CIFS_EXPERIMENTAL
- out_stop_oplock_thread:
-#endif
- kthread_stop(oplockThread);
out_unregister_dfs_key_type:
#ifdef CONFIG_CIFS_DFS_UPCALL
unregister_key_type(&key_type_dns_resolver);
cifs_destroy_inodecache();
cifs_destroy_mids();
cifs_destroy_request_bufs();
-#ifdef CONFIG_CIFS_EXPERIMENTAL
- kthread_stop(dnotifyThread);
-#endif
kthread_stop(oplockThread);
}
bool invalidHandle:1; /* file closed via session abend */
bool messageMode:1; /* for pipes: message vs byte mode */
atomic_t wrtPending; /* handle in use - defer close */
- struct semaphore fh_sem; /* prevents reopen race after dead ses*/
+ struct mutex fh_mutex; /* prevents reopen race after dead ses*/
struct cifs_search_info srch_inf;
};
bool clientCanCacheAll:1; /* read and writebehind oplock */
bool oplockPending:1;
bool delete_pending:1; /* DELETE_ON_CLOSE is set */
+ u64 server_eof; /* current file size on server */
struct inode vfs_inode;
};
__le32 Type;
__le64 DevMajor;
__le64 DevMinor;
- __u64 UniqueId;
+ __le64 UniqueId;
__le64 Permissions;
__le64 Nlinks;
} __attribute__((packed)) FILE_UNIX_BASIC_INFO; /* level 0x200 QPathInfo */
} __attribute__((packed));
struct file_internal_info {
- __u64 UniqueId; /* inode number */
+ __le64 UniqueId; /* inode number */
} __attribute__((packed)); /* level 0x3ee */
struct file_mode_info {
__le32 Type;
__le64 DevMajor;
__le64 DevMinor;
- __u64 UniqueId;
+ __le64 UniqueId;
__le64 Permissions;
__le64 Nlinks;
char FileName[1];
__le32 FileNameLength;
__le32 EaSize; /* EA size */
__le32 Reserved;
- __u64 UniqueId; /* inode num - le since Samba puts ino in low 32 bit*/
+ __le64 UniqueId; /* inode num - le since Samba puts ino in low 32 bit*/
char FileName[1];
} __attribute__((packed)) SEARCH_ID_FULL_DIR_INFO; /* level 0x105 FF rsp data */
int smb_hdr_len;
int resp_buf_type = 0;
+ *nbytes = 0;
+
cFYI(1, ("write2 at %lld %d bytes", (long long)offset, count));
if (tcon->ses->capabilities & CAP_LARGE_FILES) {
cifs_stats_inc(&tcon->num_writes);
if (rc) {
cFYI(1, ("Send error Write2 = %d", rc));
- *nbytes = 0;
} else if (resp_buf_type == 0) {
/* presumably this can not happen, but best to be safe */
rc = -EIO;
- *nbytes = 0;
} else {
WRITE_RSP *pSMBr = (WRITE_RSP *)iov[0].iov_base;
*nbytes = le16_to_cpu(pSMBr->CountHigh);
}
pfinfo = (struct file_internal_info *)
(data_offset + (char *) &pSMBr->hdr.Protocol);
- *inode_number = pfinfo->UniqueId;
+ *inode_number = le64_to_cpu(pfinfo->UniqueId);
}
}
GetInodeNumOut:
return rc;
}
+static void
+cleanup_volume_info(struct smb_vol **pvolume_info)
+{
+ struct smb_vol *volume_info;
+
+ if (!pvolume_info && !*pvolume_info)
+ return;
+
+ volume_info = *pvolume_info;
+ kzfree(volume_info->password);
+ kfree(volume_info->UNC);
+ kfree(volume_info->prepath);
+ kfree(volume_info);
+ *pvolume_info = NULL;
+ return;
+}
+
+#ifdef CONFIG_CIFS_DFS_UPCALL
+/* build_path_to_root returns full path to root when
+ * we do not have an exiting connection (tcon) */
+static char *
+build_unc_path_to_root(const struct smb_vol *volume_info,
+ const struct cifs_sb_info *cifs_sb)
+{
+ char *full_path;
+
+ int unc_len = strnlen(volume_info->UNC, MAX_TREE_SIZE + 1);
+ full_path = kmalloc(unc_len + cifs_sb->prepathlen + 1, GFP_KERNEL);
+ if (full_path == NULL)
+ return ERR_PTR(-ENOMEM);
+
+ strncpy(full_path, volume_info->UNC, unc_len);
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_POSIX_PATHS) {
+ int i;
+ for (i = 0; i < unc_len; i++) {
+ if (full_path[i] == '\\')
+ full_path[i] = '/';
+ }
+ }
+
+ if (cifs_sb->prepathlen)
+ strncpy(full_path + unc_len, cifs_sb->prepath,
+ cifs_sb->prepathlen);
+
+ full_path[unc_len + cifs_sb->prepathlen] = 0; /* add trailing null */
+ return full_path;
+}
+#endif
+
int
cifs_mount(struct super_block *sb, struct cifs_sb_info *cifs_sb,
- char *mount_data, const char *devname)
+ char *mount_data_global, const char *devname)
{
int rc = 0;
int xid;
struct cifsTconInfo *tcon = NULL;
struct TCP_Server_Info *srvTcp = NULL;
char *full_path;
+ char *mount_data = mount_data_global;
+#ifdef CONFIG_CIFS_DFS_UPCALL
+ struct dfs_info3_param *referrals = NULL;
+ unsigned int num_referrals = 0;
+try_mount_again:
+#endif
+ full_path = NULL;
xid = GetXid();
}
}
- /* check for null share name ie connect to dfs root */
if ((strchr(volume_info->UNC + 3, '\\') == NULL)
&& (strchr(volume_info->UNC + 3, '/') == NULL)) {
- /* rc = connect_to_dfs_path(...) */
- cFYI(1, ("DFS root not supported"));
+ cERROR(1, ("Missing share name"));
rc = -ENODEV;
goto mount_fail_check;
} else {
}
}
if (rc)
- goto mount_fail_check;
+ goto remote_path_check;
tcon->seal = volume_info->seal;
write_lock(&cifs_tcp_ses_lock);
list_add(&tcon->tcon_list, &pSesInfo->tcon_list);
/* BB FIXME fix time_gran to be larger for LANMAN sessions */
sb->s_time_gran = 100;
-mount_fail_check:
- /* on error free sesinfo and tcon struct if needed */
- if (rc) {
- /* If find_unc succeeded then rc == 0 so we can not end */
- /* up accidently freeing someone elses tcon struct */
- if (tcon)
- cifs_put_tcon(tcon);
- else if (pSesInfo)
- cifs_put_smb_ses(pSesInfo);
- else
- cifs_put_tcp_session(srvTcp);
- goto out;
- }
+ if (rc)
+ goto remote_path_check;
+
cifs_sb->tcon = tcon;
/* do not care if following two calls succeed - informational */
cifs_sb->rsize = min(cifs_sb->rsize,
(tcon->ses->server->maxBuf - MAX_CIFS_HDR_SIZE));
- if (!rc && cifs_sb->prepathlen) {
+remote_path_check:
+ /* check if a whole path (including prepath) is not remote */
+ if (!rc && cifs_sb->prepathlen && tcon) {
/* build_path_to_root works only when we have a valid tcon */
full_path = cifs_build_path_to_root(cifs_sb);
if (full_path == NULL) {
goto mount_fail_check;
}
rc = is_path_accessible(xid, tcon, cifs_sb, full_path);
- if (rc) {
- cERROR(1, ("Path %s in not accessible: %d",
- full_path, rc));
+ if (rc != -EREMOTE) {
kfree(full_path);
goto mount_fail_check;
}
kfree(full_path);
}
+ /* get referral if needed */
+ if (rc == -EREMOTE) {
+#ifdef CONFIG_CIFS_DFS_UPCALL
+ /* convert forward to back slashes in prepath here if needed */
+ if ((cifs_sb->mnt_cifs_flags & CIFS_MOUNT_POSIX_PATHS) == 0)
+ convert_delimiter(cifs_sb->prepath,
+ CIFS_DIR_SEP(cifs_sb));
+ full_path = build_unc_path_to_root(volume_info, cifs_sb);
+ if (IS_ERR(full_path)) {
+ rc = PTR_ERR(full_path);
+ goto mount_fail_check;
+ }
+
+ cFYI(1, ("Getting referral for: %s", full_path));
+ rc = get_dfs_path(xid, pSesInfo , full_path + 1,
+ cifs_sb->local_nls, &num_referrals, &referrals,
+ cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MAP_SPECIAL_CHR);
+ if (!rc && num_referrals > 0) {
+ char *fake_devname = NULL;
+
+ if (mount_data != mount_data_global)
+ kfree(mount_data);
+ mount_data = cifs_compose_mount_options(
+ cifs_sb->mountdata, full_path + 1,
+ referrals, &fake_devname);
+ kfree(fake_devname);
+ free_dfs_info_array(referrals, num_referrals);
+
+ if (tcon)
+ cifs_put_tcon(tcon);
+ else if (pSesInfo)
+ cifs_put_smb_ses(pSesInfo);
+
+ cleanup_volume_info(&volume_info);
+ FreeXid(xid);
+ kfree(full_path);
+ goto try_mount_again;
+ }
+#else /* No DFS support, return error on mount */
+ rc = -EOPNOTSUPP;
+#endif
+ }
+
+mount_fail_check:
+ /* on error free sesinfo and tcon struct if needed */
+ if (rc) {
+ if (mount_data != mount_data_global)
+ kfree(mount_data);
+ /* If find_unc succeeded then rc == 0 so we can not end */
+ /* up accidently freeing someone elses tcon struct */
+ if (tcon)
+ cifs_put_tcon(tcon);
+ else if (pSesInfo)
+ cifs_put_smb_ses(pSesInfo);
+ else
+ cifs_put_tcp_session(srvTcp);
+ goto out;
+ }
+
/* volume_info->password is freed above when existing session found
(in which case it is not needed anymore) but when new sesion is created
the password ptr is put in the new session structure (in which case the
password will be freed at unmount time) */
out:
/* zero out password before freeing */
- if (volume_info) {
- if (volume_info->password != NULL) {
- memset(volume_info->password, 0,
- strlen(volume_info->password));
- kfree(volume_info->password);
- }
- kfree(volume_info->UNC);
- kfree(volume_info->prepath);
- kfree(volume_info);
- }
+ cleanup_volume_info(&volume_info);
FreeXid(xid);
return rc;
}
/* We look for obvious messed up bcc or strings in response so we do not go off
the end since (at least) WIN2K and Windows XP have a major bug in not null
terminating last Unicode string in response */
- if (ses->serverOS)
- kfree(ses->serverOS);
+ kfree(ses->serverOS);
ses->serverOS = kzalloc(2 * (len + 1),
GFP_KERNEL);
if (ses->serverOS == NULL)
len = UniStrnlen((wchar_t *) bcc_ptr, remaining_words);
/* last string is not always null terminated
(for e.g. for Windows XP & 2000) */
- if (ses->serverDomain)
- kfree(ses->serverDomain);
+ kfree(ses->serverDomain);
ses->serverDomain =
kzalloc(2*(len+1),
GFP_KERNEL);
ses->serverDomain[1+(2*len)] = 0;
} else { /* else no more room so create
dummy domain string */
- if (ses->serverDomain)
- kfree(ses->serverDomain);
+ kfree(ses->serverDomain);
ses->serverDomain =
kzalloc(2, GFP_KERNEL);
}
bcc_ptr++;
len = strnlen(bcc_ptr, 1024);
- if (ses->serverDomain)
- kfree(ses->serverDomain);
+ kfree(ses->serverDomain);
ses->serverDomain = kzalloc(len + 1,
GFP_KERNEL);
if (ses->serverDomain == NULL)
/* We look for obvious messed up bcc or strings in response so we do not go off
the end since (at least) WIN2K and Windows XP have a major bug in not null
terminating last Unicode string in response */
- if (ses->serverOS)
- kfree(ses->serverOS);
+ kfree(ses->serverOS);
ses->serverOS =
kzalloc(2 * (len + 1), GFP_KERNEL);
cifs_strfromUCS_le(ses->serverOS,
if (((long) bcc_ptr + len) - (long)
pByteArea(smb_buffer_response)
<= BCC(smb_buffer_response)) {
- if (ses->serverOS)
- kfree(ses->serverOS);
+ kfree(ses->serverOS);
ses->serverOS =
kzalloc(len + 1,
GFP_KERNEL);
/* We look for obvious messed up bcc or strings in response so we do not go off
the end since (at least) WIN2K and Windows XP have a major bug in not null
terminating last Unicode string in response */
- if (ses->serverOS)
- kfree(ses->serverOS);
+ kfree(ses->serverOS);
ses->serverOS =
kzalloc(2 * (len + 1), GFP_KERNEL);
cifs_strfromUCS_le(ses->serverOS,
if (remaining_words > 0) {
len = UniStrnlen((wchar_t *) bcc_ptr, remaining_words);
/* last string not always null terminated (e.g. for Windows XP & 2000) */
- if (ses->serverDomain)
- kfree(ses->serverDomain);
+ kfree(ses->serverDomain);
ses->serverDomain =
kzalloc(2 *
(len +
= 0;
} /* else no more room so create dummy domain string */
else {
- if (ses->serverDomain)
- kfree(ses->serverDomain);
+ kfree(ses->serverDomain);
ses->serverDomain = kzalloc(2,GFP_KERNEL);
}
} else { /* no room so create dummy domain and NOS string */
- if (ses->serverDomain)
- kfree(ses->serverDomain);
+ kfree(ses->serverDomain);
ses->serverDomain = kzalloc(2, GFP_KERNEL);
kfree(ses->serverNOS);
ses->serverNOS = kzalloc(2, GFP_KERNEL);
if (((long) bcc_ptr + len) -
(long) pByteArea(smb_buffer_response)
<= BCC(smb_buffer_response)) {
- if (ses->serverOS)
- kfree(ses->serverOS);
+ kfree(ses->serverOS);
ses->serverOS = kzalloc(len + 1, GFP_KERNEL);
strncpy(ses->serverOS,bcc_ptr, len);
bcc_ptr++;
len = strnlen(bcc_ptr, 1024);
- if (ses->serverDomain)
- kfree(ses->serverDomain);
+ kfree(ses->serverDomain);
ses->serverDomain =
kzalloc(len+1,
GFP_KERNEL);
BCC(smb_buffer_response)) {
kfree(tcon->nativeFileSystem);
tcon->nativeFileSystem =
- kzalloc(2*(length + 1), GFP_KERNEL);
- if (tcon->nativeFileSystem)
+ kzalloc((4 * length) + 2, GFP_KERNEL);
+ if (tcon->nativeFileSystem) {
cifs_strfromUCS_le(
tcon->nativeFileSystem,
(__le16 *) bcc_ptr,
length, nls_codepage);
- bcc_ptr += 2 * length;
- bcc_ptr[0] = 0; /* null terminate the string */
- bcc_ptr[1] = 0;
- bcc_ptr += 2;
+ cFYI(1, ("nativeFileSystem=%s",
+ tcon->nativeFileSystem));
+ }
}
/* else do not bother copying these information fields*/
} else {
return full_path;
}
+static void
+cifs_fill_fileinfo(struct inode *newinode, __u16 fileHandle,
+ struct cifsTconInfo *tcon, bool write_only)
+{
+ int oplock = 0;
+ struct cifsFileInfo *pCifsFile;
+ struct cifsInodeInfo *pCifsInode;
+
+ pCifsFile = kzalloc(sizeof(struct cifsFileInfo), GFP_KERNEL);
+
+ if (pCifsFile == NULL)
+ return;
+
+ if (oplockEnabled)
+ oplock = REQ_OPLOCK;
+
+ pCifsFile->netfid = fileHandle;
+ pCifsFile->pid = current->tgid;
+ pCifsFile->pInode = newinode;
+ pCifsFile->invalidHandle = false;
+ pCifsFile->closePend = false;
+ mutex_init(&pCifsFile->fh_mutex);
+ mutex_init(&pCifsFile->lock_mutex);
+ INIT_LIST_HEAD(&pCifsFile->llist);
+ atomic_set(&pCifsFile->wrtPending, 0);
+
+ /* set the following in open now
+ pCifsFile->pfile = file; */
+ write_lock(&GlobalSMBSeslock);
+ list_add(&pCifsFile->tlist, &tcon->openFileList);
+ pCifsInode = CIFS_I(newinode);
+ if (pCifsInode) {
+ /* if readable file instance put first in list*/
+ if (write_only)
+ list_add_tail(&pCifsFile->flist,
+ &pCifsInode->openFileList);
+ else
+ list_add(&pCifsFile->flist, &pCifsInode->openFileList);
+
+ if ((oplock & 0xF) == OPLOCK_EXCLUSIVE) {
+ pCifsInode->clientCanCacheAll = true;
+ pCifsInode->clientCanCacheRead = true;
+ cFYI(1, ("Exclusive Oplock inode %p", newinode));
+ } else if ((oplock & 0xF) == OPLOCK_READ)
+ pCifsInode->clientCanCacheRead = true;
+ }
+ write_unlock(&GlobalSMBSeslock);
+}
+
int cifs_posix_open(char *full_path, struct inode **pinode,
struct super_block *sb, int mode, int oflags,
int *poplock, __u16 *pnetfid, int xid)
{
int rc;
__u32 oplock;
+ bool write_only = false;
FILE_UNIX_BASIC_INFO *presp_data;
__u32 posix_flags = 0;
struct cifs_sb_info *cifs_sb = CIFS_SB(sb);
if (oflags & O_DIRECT)
posix_flags |= SMB_O_DIRECT;
+ if (!(oflags & FMODE_READ))
+ write_only = true;
rc = CIFSPOSIXCreate(xid, cifs_sb->tcon, posix_flags, mode,
pnetfid, presp_data, &oplock, full_path,
if (!pinode)
goto posix_open_ret; /* caller does not need info */
- if (*pinode == NULL)
- *pinode = cifs_new_inode(sb, &presp_data->UniqueId);
+ if (*pinode == NULL) {
+ __u64 unique_id = le64_to_cpu(presp_data->UniqueId);
+ *pinode = cifs_new_inode(sb, &unique_id);
+ }
/* else an inode was passed in. Update its info, don't create one */
/* We do not need to close the file if new_inode fails since
posix_fill_in_inode(*pinode, presp_data, 1);
+ cifs_fill_fileinfo(*pinode, *pnetfid, cifs_sb->tcon, write_only);
+
posix_open_ret:
kfree(presp_data);
return rc;
char *full_path = NULL;
FILE_ALL_INFO *buf = NULL;
struct inode *newinode = NULL;
- struct cifsInodeInfo *pCifsInode;
int disposition = FILE_OVERWRITE_IF;
bool write_only = false;
/* mknod case - do not leave file open */
CIFSSMBClose(xid, tcon, fileHandle);
} else if (newinode) {
- struct cifsFileInfo *pCifsFile =
- kzalloc(sizeof(struct cifsFileInfo), GFP_KERNEL);
-
- if (pCifsFile == NULL)
- goto cifs_create_out;
- pCifsFile->netfid = fileHandle;
- pCifsFile->pid = current->tgid;
- pCifsFile->pInode = newinode;
- pCifsFile->invalidHandle = false;
- pCifsFile->closePend = false;
- init_MUTEX(&pCifsFile->fh_sem);
- mutex_init(&pCifsFile->lock_mutex);
- INIT_LIST_HEAD(&pCifsFile->llist);
- atomic_set(&pCifsFile->wrtPending, 0);
-
- /* set the following in open now
- pCifsFile->pfile = file; */
- write_lock(&GlobalSMBSeslock);
- list_add(&pCifsFile->tlist, &tcon->openFileList);
- pCifsInode = CIFS_I(newinode);
- if (pCifsInode) {
- /* if readable file instance put first in list*/
- if (write_only) {
- list_add_tail(&pCifsFile->flist,
- &pCifsInode->openFileList);
- } else {
- list_add(&pCifsFile->flist,
- &pCifsInode->openFileList);
- }
- if ((oplock & 0xF) == OPLOCK_EXCLUSIVE) {
- pCifsInode->clientCanCacheAll = true;
- pCifsInode->clientCanCacheRead = true;
- cFYI(1, ("Exclusive Oplock inode %p",
- newinode));
- } else if ((oplock & 0xF) == OPLOCK_READ)
- pCifsInode->clientCanCacheRead = true;
- }
- write_unlock(&GlobalSMBSeslock);
+ cifs_fill_fileinfo(newinode, fileHandle,
+ cifs_sb->tcon, write_only);
}
cifs_create_out:
kfree(buf);
return rc;
}
-
struct dentry *
cifs_lookup(struct inode *parent_dir_inode, struct dentry *direntry,
struct nameidata *nd)
{
int xid;
int rc = 0; /* to get around spurious gcc warning, set to zero here */
+ int oplock = 0;
+ int mode;
+ __u16 fileHandle = 0;
+ bool posix_open = false;
struct cifs_sb_info *cifs_sb;
struct cifsTconInfo *pTcon;
struct inode *newInode = NULL;
char *full_path = NULL;
+ struct file *filp;
xid = GetXid();
}
cFYI(1, ("Full path: %s inode = 0x%p", full_path, direntry->d_inode));
- if (pTcon->unix_ext)
- rc = cifs_get_inode_info_unix(&newInode, full_path,
- parent_dir_inode->i_sb, xid);
- else
+ if (pTcon->unix_ext) {
+ if (!(nd->flags & (LOOKUP_PARENT | LOOKUP_DIRECTORY)) &&
+ (nd->flags & LOOKUP_OPEN)) {
+ if (!((nd->intent.open.flags & O_CREAT) &&
+ (nd->intent.open.flags & O_EXCL))) {
+ mode = nd->intent.open.create_mode &
+ ~current_umask();
+ rc = cifs_posix_open(full_path, &newInode,
+ parent_dir_inode->i_sb, mode,
+ nd->intent.open.flags, &oplock,
+ &fileHandle, xid);
+ /*
+ * This code works around a bug in
+ * samba posix open in samba versions 3.3.1
+ * and earlier where create works
+ * but open fails with invalid parameter.
+ * If either of these error codes are
+ * returned, follow the normal lookup.
+ * Otherwise, the error during posix open
+ * is handled.
+ */
+ if ((rc != -EINVAL) && (rc != -EOPNOTSUPP))
+ posix_open = true;
+ }
+ }
+ if (!posix_open)
+ rc = cifs_get_inode_info_unix(&newInode, full_path,
+ parent_dir_inode->i_sb, xid);
+ } else
rc = cifs_get_inode_info(&newInode, full_path, NULL,
- parent_dir_inode->i_sb, xid, NULL);
+ parent_dir_inode->i_sb, xid, NULL);
if ((rc == 0) && (newInode != NULL)) {
if (pTcon->nocase)
else
direntry->d_op = &cifs_dentry_ops;
d_add(direntry, newInode);
-
+ if (posix_open)
+ filp = lookup_instantiate_filp(nd, direntry, NULL);
/* since paths are not looked up by component - the parent
directories are presumed to be good here */
renew_parental_timestamps(direntry);
}
key->type_data.x[0] = datalen;
- rcu_assign_pointer(key->payload.data, ip);
+ key->payload.data = ip;
return rc;
}
memset(private_data, 0, sizeof(struct cifsFileInfo));
private_data->netfid = netfid;
private_data->pid = current->tgid;
- init_MUTEX(&private_data->fh_sem);
+ mutex_init(&private_data->fh_mutex);
mutex_init(&private_data->lock_mutex);
INIT_LIST_HEAD(&private_data->llist);
private_data->pfile = file; /* needed for writepage */
cifs_sb = CIFS_SB(inode->i_sb);
tcon = cifs_sb->tcon;
- if (file->f_flags & O_CREAT) {
- /* search inode for this file and fill in file->private_data */
- pCifsInode = CIFS_I(file->f_path.dentry->d_inode);
- read_lock(&GlobalSMBSeslock);
- list_for_each(tmp, &pCifsInode->openFileList) {
- pCifsFile = list_entry(tmp, struct cifsFileInfo,
- flist);
- if ((pCifsFile->pfile == NULL) &&
- (pCifsFile->pid == current->tgid)) {
- /* mode set in cifs_create */
-
- /* needed for writepage */
- pCifsFile->pfile = file;
-
- file->private_data = pCifsFile;
- break;
- }
- }
- read_unlock(&GlobalSMBSeslock);
- if (file->private_data != NULL) {
- rc = 0;
- FreeXid(xid);
- return rc;
- } else {
- if (file->f_flags & O_EXCL)
- cERROR(1, ("could not find file instance for "
- "new file %p", file));
+ /* search inode for this file and fill in file->private_data */
+ pCifsInode = CIFS_I(file->f_path.dentry->d_inode);
+ read_lock(&GlobalSMBSeslock);
+ list_for_each(tmp, &pCifsInode->openFileList) {
+ pCifsFile = list_entry(tmp, struct cifsFileInfo,
+ flist);
+ if ((pCifsFile->pfile == NULL) &&
+ (pCifsFile->pid == current->tgid)) {
+ /* mode set in cifs_create */
+
+ /* needed for writepage */
+ pCifsFile->pfile = file;
+
+ file->private_data = pCifsFile;
+ break;
}
}
+ read_unlock(&GlobalSMBSeslock);
+
+ if (file->private_data != NULL) {
+ rc = 0;
+ FreeXid(xid);
+ return rc;
+ } else if ((file->f_flags & O_CREAT) && (file->f_flags & O_EXCL))
+ cERROR(1, ("could not find file instance for "
+ "new file %p", file));
full_path = build_path_from_dentry(file->f_path.dentry);
if (full_path == NULL) {
return -EBADF;
xid = GetXid();
- down(&pCifsFile->fh_sem);
+ mutex_unlock(&pCifsFile->fh_mutex);
if (!pCifsFile->invalidHandle) {
- up(&pCifsFile->fh_sem);
+ mutex_lock(&pCifsFile->fh_mutex);
FreeXid(xid);
return 0;
}
if (full_path == NULL) {
rc = -ENOMEM;
reopen_error_exit:
- up(&pCifsFile->fh_sem);
+ mutex_lock(&pCifsFile->fh_mutex);
FreeXid(xid);
return rc;
}
cifs_sb->local_nls, cifs_sb->mnt_cifs_flags &
CIFS_MOUNT_MAP_SPECIAL_CHR);
if (rc) {
- up(&pCifsFile->fh_sem);
+ mutex_lock(&pCifsFile->fh_mutex);
cFYI(1, ("cifs_open returned 0x%x", rc));
cFYI(1, ("oplock: %d", oplock));
} else {
reopen_success:
pCifsFile->netfid = netfid;
pCifsFile->invalidHandle = false;
- up(&pCifsFile->fh_sem);
+ mutex_lock(&pCifsFile->fh_mutex);
pCifsInode = CIFS_I(inode);
if (pCifsInode) {
if (can_flush) {
return rc;
}
+/*
+ * Set the timeout on write requests past EOF. For some servers (Windows)
+ * these calls can be very long.
+ *
+ * If we're writing >10M past the EOF we give a 180s timeout. Anything less
+ * than that gets a 45s timeout. Writes not past EOF get 15s timeouts.
+ * The 10M cutoff is totally arbitrary. A better scheme for this would be
+ * welcome if someone wants to suggest one.
+ *
+ * We may be able to do a better job with this if there were some way to
+ * declare that a file should be sparse.
+ */
+static int
+cifs_write_timeout(struct cifsInodeInfo *cifsi, loff_t offset)
+{
+ if (offset <= cifsi->server_eof)
+ return CIFS_STD_OP;
+ else if (offset > (cifsi->server_eof + (10 * 1024 * 1024)))
+ return CIFS_VLONG_OP;
+ else
+ return CIFS_LONG_OP;
+}
+
+/* update the file size (if needed) after a write */
+static void
+cifs_update_eof(struct cifsInodeInfo *cifsi, loff_t offset,
+ unsigned int bytes_written)
+{
+ loff_t end_of_write = offset + bytes_written;
+
+ if (end_of_write > cifsi->server_eof)
+ cifsi->server_eof = end_of_write;
+}
+
ssize_t cifs_user_write(struct file *file, const char __user *write_data,
size_t write_size, loff_t *poffset)
{
struct cifsTconInfo *pTcon;
int xid, long_op;
struct cifsFileInfo *open_file;
+ struct cifsInodeInfo *cifsi = CIFS_I(file->f_path.dentry->d_inode);
cifs_sb = CIFS_SB(file->f_path.dentry->d_sb);
xid = GetXid();
- if (*poffset > file->f_path.dentry->d_inode->i_size)
- long_op = CIFS_VLONG_OP; /* writes past EOF take long time */
- else
- long_op = CIFS_LONG_OP;
-
+ long_op = cifs_write_timeout(cifsi, *poffset);
for (total_written = 0; write_size > total_written;
total_written += bytes_written) {
rc = -EAGAIN;
FreeXid(xid);
return rc;
}
- } else
+ } else {
+ cifs_update_eof(cifsi, *poffset, bytes_written);
*poffset += bytes_written;
+ }
long_op = CIFS_STD_OP; /* subsequent writes fast -
15 seconds is plenty */
}
struct cifsTconInfo *pTcon;
int xid, long_op;
struct cifsFileInfo *open_file;
+ struct cifsInodeInfo *cifsi = CIFS_I(file->f_path.dentry->d_inode);
cifs_sb = CIFS_SB(file->f_path.dentry->d_sb);
xid = GetXid();
- if (*poffset > file->f_path.dentry->d_inode->i_size)
- long_op = CIFS_VLONG_OP; /* writes past EOF can be slow */
- else
- long_op = CIFS_LONG_OP;
-
+ long_op = cifs_write_timeout(cifsi, *poffset);
for (total_written = 0; write_size > total_written;
total_written += bytes_written) {
rc = -EAGAIN;
FreeXid(xid);
return rc;
}
- } else
+ } else {
+ cifs_update_eof(cifsi, *poffset, bytes_written);
*poffset += bytes_written;
+ }
long_op = CIFS_STD_OP; /* subsequent writes fast -
15 seconds is plenty */
}
int nr_pages;
__u64 offset = 0;
struct cifsFileInfo *open_file;
+ struct cifsInodeInfo *cifsi = CIFS_I(mapping->host);
struct page *page;
struct pagevec pvec;
int rc = 0;
int scanned = 0;
- int xid;
+ int xid, long_op;
cifs_sb = CIFS_SB(mapping->host->i_sb);
cERROR(1, ("No writable handles for inode"));
rc = -EBADF;
} else {
+ long_op = cifs_write_timeout(cifsi, offset);
rc = CIFSSMBWrite2(xid, cifs_sb->tcon,
open_file->netfid,
bytes_to_write, offset,
&bytes_written, iov, n_iov,
- CIFS_LONG_OP);
+ long_op);
atomic_dec(&open_file->wrtPending);
+ cifs_update_eof(cifsi, offset, bytes_written);
+
if (rc || bytes_written < bytes_to_write) {
cERROR(1, ("Write2 ret %d, wrote %d",
rc, bytes_written));
inode->i_nlink = le64_to_cpu(info->Nlinks);
+ cifsInfo->server_eof = end_of_file;
spin_lock(&inode->i_lock);
if (is_size_safe_to_change(cifsInfo, end_of_file)) {
/*
/* get new inode */
if (*pinode == NULL) {
- *pinode = cifs_new_inode(sb, &find_data.UniqueId);
+ __u64 unique_id = le64_to_cpu(find_data.UniqueId);
+ *pinode = cifs_new_inode(sb, &unique_id);
if (*pinode == NULL) {
rc = -ENOMEM;
goto cgiiu_exit;
inode->i_mode |= S_IFREG;
}
+ cifsInfo->server_eof = le64_to_cpu(pfindData->EndOfFile);
spin_lock(&inode->i_lock);
- if (is_size_safe_to_change(cifsInfo,
- le64_to_cpu(pfindData->EndOfFile))) {
+ if (is_size_safe_to_change(cifsInfo, cifsInfo->server_eof)) {
/* can not safely shrink the file size here if the
client is writing to it due to potential races */
- i_size_write(inode, le64_to_cpu(pfindData->EndOfFile));
+ i_size_write(inode, cifsInfo->server_eof);
/* 512 bytes (2**9) is the fake blocksize that must be
used for this calculation */
cFYI(1, ("posix mkdir returned 0x%x", rc));
d_drop(direntry);
} else {
+ __u64 unique_id;
if (pInfo->Type == cpu_to_le32(-1)) {
/* no return info, go query for it */
kfree(pInfo);
else
direntry->d_op = &cifs_dentry_ops;
- newinode = cifs_new_inode(inode->i_sb,
- &pInfo->UniqueId);
+ unique_id = le64_to_cpu(pInfo->UniqueId);
+ newinode = cifs_new_inode(inode->i_sb, &unique_id);
if (newinode == NULL) {
kfree(pInfo);
goto mkdir_get_info;
checking the UniqueId via FILE_INTERNAL_INFO */
unlink_target:
- if ((rc == -EACCES) || (rc == -EEXIST)) {
+ /* Try unlinking the target dentry if it's not negative */
+ if (target_dentry->d_inode && (rc == -EACCES || rc == -EEXIST)) {
tmprc = cifs_unlink(target_dir, target_dentry);
if (tmprc)
goto cifs_rename_exit;
}
if (rc == 0) {
+ cifsInode->server_eof = attrs->ia_size;
rc = cifs_vmtruncate(inode, attrs->ia_size);
cifs_truncate_page(inode->i_mapping, inode->i_size);
}
goto out;
}
- if ((attrs->ia_valid & ATTR_MTIME) || (attrs->ia_valid & ATTR_SIZE)) {
- /*
- Flush data before changing file size or changing the last
- write time of the file on the server. If the
- flush returns error, store it to report later and continue.
- BB: This should be smarter. Why bother flushing pages that
- will be truncated anyway? Also, should we error out here if
- the flush returns error?
- */
- rc = filemap_write_and_wait(inode->i_mapping);
- if (rc != 0) {
- cifsInode->write_behind_rc = rc;
- rc = 0;
- }
+ /*
+ * Attempt to flush data before changing attributes. We need to do
+ * this for ATTR_SIZE and ATTR_MTIME for sure, and if we change the
+ * ownership or mode then we may also need to do this. Here, we take
+ * the safe way out and just do the flush on all setattr requests. If
+ * the flush returns error, store it to report later and continue.
+ *
+ * BB: This should be smarter. Why bother flushing pages that
+ * will be truncated anyway? Also, should we error out here if
+ * the flush returns error?
+ */
+ rc = filemap_write_and_wait(inode->i_mapping);
+ if (rc != 0) {
+ cifsInode->write_behind_rc = rc;
+ rc = 0;
}
if (attrs->ia_valid & ATTR_SIZE) {
return -ENOMEM;
}
- if ((attrs->ia_valid & ATTR_MTIME) || (attrs->ia_valid & ATTR_SIZE)) {
- /*
- Flush data before changing file size or changing the last
- write time of the file on the server. If the
- flush returns error, store it to report later and continue.
- BB: This should be smarter. Why bother flushing pages that
- will be truncated anyway? Also, should we error out here if
- the flush returns error?
- */
- rc = filemap_write_and_wait(inode->i_mapping);
- if (rc != 0) {
- cifsInode->write_behind_rc = rc;
- rc = 0;
- }
+ /*
+ * Attempt to flush data before changing attributes. We need to do
+ * this for ATTR_SIZE and ATTR_MTIME for sure, and if we change the
+ * ownership or mode then we may also need to do this. Here, we take
+ * the safe way out and just do the flush on all setattr requests. If
+ * the flush returns error, store it to report later and continue.
+ *
+ * BB: This should be smarter. Why bother flushing pages that
+ * will be truncated anyway? Also, should we error out here if
+ * the flush returns error?
+ */
+ rc = filemap_write_and_wait(inode->i_mapping);
+ if (rc != 0) {
+ cifsInode->write_behind_rc = rc;
+ rc = 0;
}
if (attrs->ia_valid & ATTR_SIZE) {
if (atomic_read(&cifsInfo->inUse) == 0)
atomic_set(&cifsInfo->inUse, 1);
+ cifsInfo->server_eof = end_of_file;
spin_lock(&tmp_inode->i_lock);
if (is_size_safe_to_change(cifsInfo, end_of_file)) {
/* can not safely change the file size here if the
tmp_inode->i_gid = le64_to_cpu(pfindData->Gid);
tmp_inode->i_nlink = le64_to_cpu(pfindData->Nlinks);
+ cifsInfo->server_eof = end_of_file;
spin_lock(&tmp_inode->i_lock);
if (is_size_safe_to_change(cifsInfo, end_of_file)) {
/* can not safely change the file size here if the
len = strnlen(filename, PATH_MAX);
}
- *pinum = pFindData->UniqueId;
+ *pinum = le64_to_cpu(pFindData->UniqueId);
} else if (level == SMB_FIND_FILE_DIRECTORY_INFO) {
FILE_DIRECTORY_INFO *pFindData =
(FILE_DIRECTORY_INFO *)current_entry;
(SEARCH_ID_FULL_DIR_INFO *)current_entry;
filename = &pFindData->FileName[0];
len = le32_to_cpu(pFindData->FileNameLength);
- *pinum = pFindData->UniqueId;
+ *pinum = le64_to_cpu(pFindData->UniqueId);
} else if (level == SMB_FIND_FILE_BOTH_DIRECTORY_INFO) {
FILE_BOTH_DIRECTORY_INFO *pFindData =
(FILE_BOTH_DIRECTORY_INFO *)current_entry;
int words_left, len;
char *data = *pbcc_area;
-
-
cFYI(1, ("bleft %d", bleft));
-
- /* SMB header is unaligned, so cifs servers word align start of
- Unicode strings */
- data++;
- bleft--; /* Windows servers do not always double null terminate
- their final Unicode string - in which case we
- now will not attempt to decode the byte of junk
- which follows it */
+ /*
+ * Windows servers do not always double null terminate their final
+ * Unicode string. Check to see if there are an uneven number of bytes
+ * left. If so, then add an extra NULL pad byte to the end of the
+ * response.
+ *
+ * See section 2.7.2 in "Implementing CIFS" for details
+ */
+ if (bleft % 2) {
+ data[bleft] = 0;
+ ++bleft;
+ }
words_left = bleft / 2;
/* save off server operating system */
len = UniStrnlen((wchar_t *) data, words_left);
-/* We look for obvious messed up bcc or strings in response so we do not go off
- the end since (at least) WIN2K and Windows XP have a major bug in not null
- terminating last Unicode string in response */
if (len >= words_left)
return rc;
kfree(ses->serverOS);
/* UTF-8 string will not grow more than four times as big as UCS-16 */
ses->serverOS = kzalloc((4 * len) + 2 /* trailing null */, GFP_KERNEL);
- if (ses->serverOS != NULL)
+ if (ses->serverOS != NULL) {
cifs_strfromUCS_le(ses->serverOS, (__le16 *)data, len, nls_cp);
+ cFYI(1, ("serverOS=%s", ses->serverOS));
+ }
data += 2 * (len + 1);
words_left -= len + 1;
if (ses->serverNOS != NULL) {
cifs_strfromUCS_le(ses->serverNOS, (__le16 *)data, len,
nls_cp);
+ cFYI(1, ("serverNOS=%s", ses->serverNOS));
if (strncmp(ses->serverNOS, "NT LAN Manager 4", 16) == 0) {
cFYI(1, ("NT4 server"));
ses->flags |= CIFS_SES_NT4;
return rc;
kfree(ses->serverDomain);
- ses->serverDomain = kzalloc(2 * (len + 1), GFP_KERNEL); /* BB FIXME wrong length */
+ ses->serverDomain = kzalloc((4 * len) + 2, GFP_KERNEL);
if (ses->serverDomain != NULL) {
cifs_strfromUCS_le(ses->serverDomain, (__le16 *)data, len,
nls_cp);
- ses->serverDomain[2*len] = 0;
- ses->serverDomain[(2*len) + 1] = 0;
+ cFYI(1, ("serverDomain=%s", ses->serverDomain));
}
data += 2 * (len + 1);
words_left -= len + 1;
}
/* BB check if Unicode and decode strings */
- if (smb_buf->Flags2 & SMBFLG2_UNICODE)
+ if (smb_buf->Flags2 & SMBFLG2_UNICODE) {
+ /* unicode string area must be word-aligned */
+ if (((unsigned long) bcc_ptr - (unsigned long) smb_buf) % 2) {
+ ++bcc_ptr;
+ --bytes_remaining;
+ }
rc = decode_unicode_ssetup(&bcc_ptr, bytes_remaining,
- ses, nls_cp);
- else
+ ses, nls_cp);
+ } else {
rc = decode_ascii_ssetup(&bcc_ptr, bytes_remaining,
ses, nls_cp);
+ }
ssetup_exit:
if (spnego_key) {
struct bio *bio;
bio = bio_alloc(GFP_KERNEL, nr_vecs);
- if (bio == NULL)
- return -ENOMEM;
bio->bi_bdev = bdev;
bio->bi_sector = first_sector;
len = ee_len;
bio = bio_alloc(GFP_NOIO, len);
- if (!bio)
- return -ENOMEM;
bio->bi_sector = ee_pblock;
bio->bi_bdev = inode->i_sb->s_bdev;
Note that "utf8" is not recommended for FAT filesystems.
If unsure, you shouldn't set "utf8" here.
See <file:Documentation/filesystems/vfat.txt> for more information.
+
+ Enable any character sets you need in File Systems/Native Language
+ Support.
GLOCK_BUG_ON(gl, test_bit(GLF_DEMOTE_IN_PROGRESS, &gl->gl_flags));
- down_read(&gfs2_umount_flush_sem);
if (test_bit(GLF_DEMOTE, &gl->gl_flags) &&
gl->gl_demote_state != gl->gl_state) {
if (find_first_holder(gl))
if (ret == 0)
goto out_unlock;
if (ret == 2)
- goto out_sem;
+ goto out;
gh = find_first_waiter(gl);
gl->gl_target = gh->gh_state;
if (!(gh->gh_flags & (LM_FLAG_TRY | LM_FLAG_TRY_1CB)))
do_error(gl, 0); /* Fail queued try locks */
}
do_xmote(gl, gh, gl->gl_target);
-out_sem:
- up_read(&gfs2_umount_flush_sem);
+out:
return;
out_sched:
gfs2_glock_put(gl);
out_unlock:
clear_bit(GLF_LOCK, &gl->gl_flags);
- goto out_sem;
+ goto out;
}
static void glock_work_func(struct work_struct *work)
if (test_and_clear_bit(GLF_REPLY_PENDING, &gl->gl_flags))
finish_xmote(gl, gl->gl_reply);
+ down_read(&gfs2_umount_flush_sem);
spin_lock(&gl->gl_spin);
if (test_and_clear_bit(GLF_PENDING_DEMOTE, &gl->gl_flags) &&
gl->gl_state != LM_ST_UNLOCKED &&
}
run_queue(gl, 0);
spin_unlock(&gl->gl_spin);
+ up_read(&gfs2_umount_flush_sem);
if (!delay ||
queue_delayed_work(glock_workqueue, &gl->gl_work, delay) == 0)
gfs2_glock_put(gl);
if (S_ISREG(mode)) {
inode->i_op = &gfs2_file_iops;
if (gfs2_localflocks(sdp))
- inode->i_fop = gfs2_file_fops_nolock;
+ inode->i_fop = &gfs2_file_fops_nolock;
else
- inode->i_fop = gfs2_file_fops;
+ inode->i_fop = &gfs2_file_fops;
} else if (S_ISDIR(mode)) {
inode->i_op = &gfs2_dir_iops;
if (gfs2_localflocks(sdp))
- inode->i_fop = gfs2_dir_fops_nolock;
+ inode->i_fop = &gfs2_dir_fops_nolock;
else
- inode->i_fop = gfs2_dir_fops;
+ inode->i_fop = &gfs2_dir_fops;
} else if (S_ISLNK(mode)) {
inode->i_op = &gfs2_symlink_iops;
} else {
extern const struct inode_operations gfs2_file_iops;
extern const struct inode_operations gfs2_dir_iops;
extern const struct inode_operations gfs2_symlink_iops;
-extern const struct file_operations *gfs2_file_fops_nolock;
-extern const struct file_operations *gfs2_dir_fops_nolock;
+extern const struct file_operations gfs2_file_fops_nolock;
+extern const struct file_operations gfs2_dir_fops_nolock;
extern void gfs2_set_inode_flags(struct inode *inode);
#ifdef CONFIG_GFS2_FS_LOCKING_DLM
-extern const struct file_operations *gfs2_file_fops;
-extern const struct file_operations *gfs2_dir_fops;
+extern const struct file_operations gfs2_file_fops;
+extern const struct file_operations gfs2_dir_fops;
+
static inline int gfs2_localflocks(const struct gfs2_sbd *sdp)
{
return sdp->sd_args.ar_localflocks;
}
#else /* Single node only */
-#define gfs2_file_fops NULL
-#define gfs2_dir_fops NULL
+#define gfs2_file_fops gfs2_file_fops_nolock
+#define gfs2_dir_fops gfs2_dir_fops_nolock
+
static inline int gfs2_localflocks(const struct gfs2_sbd *sdp)
{
return 1;
}
}
-const struct file_operations *gfs2_file_fops = &(const struct file_operations){
+const struct file_operations gfs2_file_fops = {
.llseek = gfs2_llseek,
.read = do_sync_read,
.aio_read = generic_file_aio_read,
.setlease = gfs2_setlease,
};
-const struct file_operations *gfs2_dir_fops = &(const struct file_operations){
+const struct file_operations gfs2_dir_fops = {
.readdir = gfs2_readdir,
.unlocked_ioctl = gfs2_ioctl,
.open = gfs2_open,
#endif /* CONFIG_GFS2_FS_LOCKING_DLM */
-const struct file_operations *gfs2_file_fops_nolock = &(const struct file_operations){
+const struct file_operations gfs2_file_fops_nolock = {
.llseek = gfs2_llseek,
.read = do_sync_read,
.aio_read = generic_file_aio_read,
.setlease = generic_setlease,
};
-const struct file_operations *gfs2_dir_fops_nolock = &(const struct file_operations){
+const struct file_operations gfs2_dir_fops_nolock = {
.readdir = gfs2_readdir,
.unlocked_ioctl = gfs2_ioctl,
.open = gfs2_open,
lock_page(page);
bio = bio_alloc(GFP_NOFS, 1);
- if (unlikely(!bio)) {
- __free_page(page);
- return -ENOBUFS;
- }
-
bio->bi_sector = sector * (sb->s_blocksize >> 9);
bio->bi_bdev = sb->s_bdev;
bio_add_page(bio, page, PAGE_SIZE, 0);
ip = ghs[1].gh_gl->gl_object;
ip->i_disksize = size;
+ i_size_write(inode, size);
error = gfs2_meta_inode_buffer(ip, &dibh);
static LIST_HEAD(qd_lru_list);
static atomic_t qd_lru_count = ATOMIC_INIT(0);
-static spinlock_t qd_lru_lock = SPIN_LOCK_UNLOCKED;
+static DEFINE_SPINLOCK(qd_lru_lock);
int gfs2_shrink_qd_memory(int nr, gfp_t gfp_mask)
{
refrigerator();
t = min(quotad_timeo, statfs_timeo);
- prepare_to_wait(&sdp->sd_quota_wait, &wait, TASK_UNINTERRUPTIBLE);
+ prepare_to_wait(&sdp->sd_quota_wait, &wait, TASK_INTERRUPTIBLE);
spin_lock(&sdp->sd_trunc_lock);
empty = list_empty(&sdp->sd_trunc_list);
spin_unlock(&sdp->sd_trunc_lock);
spin_lock(&inode_lock);
}
-/*
- * We rarely want to lock two inodes that do not have a parent/child
- * relationship (such as directory, child inode) simultaneously. The
- * vast majority of file systems should be able to get along fine
- * without this. Do not use these functions except as a last resort.
- */
-void inode_double_lock(struct inode *inode1, struct inode *inode2)
-{
- if (inode1 == NULL || inode2 == NULL || inode1 == inode2) {
- if (inode1)
- mutex_lock(&inode1->i_mutex);
- else if (inode2)
- mutex_lock(&inode2->i_mutex);
- return;
- }
-
- if (inode1 < inode2) {
- mutex_lock_nested(&inode1->i_mutex, I_MUTEX_PARENT);
- mutex_lock_nested(&inode2->i_mutex, I_MUTEX_CHILD);
- } else {
- mutex_lock_nested(&inode2->i_mutex, I_MUTEX_PARENT);
- mutex_lock_nested(&inode1->i_mutex, I_MUTEX_CHILD);
- }
-}
-EXPORT_SYMBOL(inode_double_lock);
-
-void inode_double_unlock(struct inode *inode1, struct inode *inode2)
-{
- if (inode1)
- mutex_unlock(&inode1->i_mutex);
-
- if (inode2 && inode2 != inode1)
- mutex_unlock(&inode2->i_mutex);
-}
-EXPORT_SYMBOL(inode_double_unlock);
-
static __initdata unsigned long ihash_entries;
static int __init set_ihash_entries(char *str)
{
if (data_page)
((char *)data_page)[PAGE_SIZE - 1] = 0;
- /* Default to relatime */
- mnt_flags |= MNT_RELATIME;
+ /* Default to relatime unless overriden */
+ if (!(flags & MS_NOATIME))
+ mnt_flags |= MNT_RELATIME;
/* Separate the per-mountpoint flags */
if (flags & MS_NOSUID)
return written ? written : ret;
}
+static int ocfs2_splice_to_file(struct pipe_inode_info *pipe,
+ struct file *out,
+ struct splice_desc *sd)
+{
+ int ret;
+
+ ret = ocfs2_prepare_inode_for_write(out->f_path.dentry, &sd->pos,
+ sd->total_len, 0, NULL);
+ if (ret < 0) {
+ mlog_errno(ret);
+ return ret;
+ }
+
+ return splice_from_pipe_feed(pipe, sd, pipe_to_file);
+}
+
static ssize_t ocfs2_file_splice_write(struct pipe_inode_info *pipe,
struct file *out,
loff_t *ppos,
unsigned int flags)
{
int ret;
- struct inode *inode = out->f_path.dentry->d_inode;
+ struct address_space *mapping = out->f_mapping;
+ struct inode *inode = mapping->host;
+ struct splice_desc sd = {
+ .total_len = len,
+ .flags = flags,
+ .pos = *ppos,
+ .u.file = out,
+ };
mlog_entry("(0x%p, 0x%p, %u, '%.*s')\n", out, pipe,
(unsigned int)len,
out->f_path.dentry->d_name.len,
out->f_path.dentry->d_name.name);
- mutex_lock_nested(&inode->i_mutex, I_MUTEX_PARENT);
+ if (pipe->inode)
+ mutex_lock_nested(&pipe->inode->i_mutex, I_MUTEX_PARENT);
- ret = ocfs2_rw_lock(inode, 1);
- if (ret < 0) {
- mlog_errno(ret);
- goto out;
- }
+ splice_from_pipe_begin(&sd);
+ do {
+ ret = splice_from_pipe_next(pipe, &sd);
+ if (ret <= 0)
+ break;
- ret = ocfs2_prepare_inode_for_write(out->f_path.dentry, ppos, len, 0,
- NULL);
- if (ret < 0) {
- mlog_errno(ret);
- goto out_unlock;
- }
+ mutex_lock_nested(&inode->i_mutex, I_MUTEX_CHILD);
+ ret = ocfs2_rw_lock(inode, 1);
+ if (ret < 0)
+ mlog_errno(ret);
+ else {
+ ret = ocfs2_splice_to_file(pipe, out, &sd);
+ ocfs2_rw_unlock(inode, 1);
+ }
+ mutex_unlock(&inode->i_mutex);
+ } while (ret > 0);
+ splice_from_pipe_end(pipe, &sd);
if (pipe->inode)
- mutex_lock_nested(&pipe->inode->i_mutex, I_MUTEX_CHILD);
- ret = generic_file_splice_write_nolock(pipe, out, ppos, len, flags);
- if (pipe->inode)
mutex_unlock(&pipe->inode->i_mutex);
-out_unlock:
- ocfs2_rw_unlock(inode, 1);
-out:
- mutex_unlock(&inode->i_mutex);
+ if (sd.num_spliced)
+ ret = sd.num_spliced;
+
+ if (ret > 0) {
+ unsigned long nr_pages;
+
+ *ppos += ret;
+ nr_pages = (ret + PAGE_CACHE_SIZE - 1) >> PAGE_CACHE_SHIFT;
+
+ /*
+ * If file or inode is SYNC and we actually wrote some data,
+ * sync it.
+ */
+ if (unlikely((out->f_flags & O_SYNC) || IS_SYNC(inode))) {
+ int err;
+
+ mutex_lock(&inode->i_mutex);
+ err = ocfs2_rw_lock(inode, 1);
+ if (err < 0) {
+ mlog_errno(err);
+ } else {
+ err = generic_osync_inode(inode, mapping,
+ OSYNC_METADATA|OSYNC_DATA);
+ ocfs2_rw_unlock(inode, 1);
+ }
+ mutex_unlock(&inode->i_mutex);
+
+ if (err)
+ ret = err;
+ }
+ balance_dirty_pages_ratelimited_nr(mapping, nr_pages);
+ }
mlog_exit(ret);
return ret;
* -- Manfred Spraul <manfred@colorfullife.com> 2002-05-09
*/
+static void pipe_lock_nested(struct pipe_inode_info *pipe, int subclass)
+{
+ if (pipe->inode)
+ mutex_lock_nested(&pipe->inode->i_mutex, subclass);
+}
+
+void pipe_lock(struct pipe_inode_info *pipe)
+{
+ /*
+ * pipe_lock() nests non-pipe inode locks (for writing to a file)
+ */
+ pipe_lock_nested(pipe, I_MUTEX_PARENT);
+}
+EXPORT_SYMBOL(pipe_lock);
+
+void pipe_unlock(struct pipe_inode_info *pipe)
+{
+ if (pipe->inode)
+ mutex_unlock(&pipe->inode->i_mutex);
+}
+EXPORT_SYMBOL(pipe_unlock);
+
+void pipe_double_lock(struct pipe_inode_info *pipe1,
+ struct pipe_inode_info *pipe2)
+{
+ BUG_ON(pipe1 == pipe2);
+
+ if (pipe1 < pipe2) {
+ pipe_lock_nested(pipe1, I_MUTEX_PARENT);
+ pipe_lock_nested(pipe2, I_MUTEX_CHILD);
+ } else {
+ pipe_lock_nested(pipe2, I_MUTEX_CHILD);
+ pipe_lock_nested(pipe1, I_MUTEX_PARENT);
+ }
+}
+
/* Drop the inode semaphore and wait for a pipe event, atomically */
void pipe_wait(struct pipe_inode_info *pipe)
{
* is considered a noninteractive wait:
*/
prepare_to_wait(&pipe->wait, &wait, TASK_INTERRUPTIBLE);
- if (pipe->inode)
- mutex_unlock(&pipe->inode->i_mutex);
+ pipe_unlock(pipe);
schedule();
finish_wait(&pipe->wait, &wait);
- if (pipe->inode)
- mutex_lock(&pipe->inode->i_mutex);
+ pipe_lock(pipe);
}
static int
{
struct proc_mounts *p = file->private_data;
struct mnt_namespace *ns = p->ns;
- unsigned res = 0;
+ unsigned res = POLLIN | POLLRDNORM;
poll_wait(file, &ns->poll, wait);
spin_lock(&vfsmount_lock);
if (p->event != ns->event) {
p->event = ns->event;
- res = POLLERR;
+ res |= POLLERR | POLLPRI;
}
spin_unlock(&vfsmount_lock);
do_wakeup = 0;
page_nr = 0;
- if (pipe->inode)
- mutex_lock(&pipe->inode->i_mutex);
+ pipe_lock(pipe);
for (;;) {
if (!pipe->readers) {
pipe->waiting_writers--;
}
- if (pipe->inode) {
- mutex_unlock(&pipe->inode->i_mutex);
+ pipe_unlock(pipe);
- if (do_wakeup) {
- smp_mb();
- if (waitqueue_active(&pipe->wait))
- wake_up_interruptible(&pipe->wait);
- kill_fasync(&pipe->fasync_readers, SIGIO, POLL_IN);
- }
+ if (do_wakeup) {
+ smp_mb();
+ if (waitqueue_active(&pipe->wait))
+ wake_up_interruptible(&pipe->wait);
+ kill_fasync(&pipe->fasync_readers, SIGIO, POLL_IN);
}
while (page_nr < spd_pages)
* SPLICE_F_MOVE isn't set, or we cannot move the page, we simply create
* a new page in the output file page cache and fill/dirty that.
*/
-static int pipe_to_file(struct pipe_inode_info *pipe, struct pipe_buffer *buf,
- struct splice_desc *sd)
+int pipe_to_file(struct pipe_inode_info *pipe, struct pipe_buffer *buf,
+ struct splice_desc *sd)
{
struct file *file = sd->u.file;
struct address_space *mapping = file->f_mapping;
out:
return ret;
}
+EXPORT_SYMBOL(pipe_to_file);
+
+static void wakeup_pipe_writers(struct pipe_inode_info *pipe)
+{
+ smp_mb();
+ if (waitqueue_active(&pipe->wait))
+ wake_up_interruptible(&pipe->wait);
+ kill_fasync(&pipe->fasync_writers, SIGIO, POLL_OUT);
+}
/**
- * __splice_from_pipe - splice data from a pipe to given actor
+ * splice_from_pipe_feed - feed available data from a pipe to a file
* @pipe: pipe to splice from
* @sd: information to @actor
* @actor: handler that splices the data
*
* Description:
- * This function does little more than loop over the pipe and call
- * @actor to do the actual moving of a single struct pipe_buffer to
- * the desired destination. See pipe_to_file, pipe_to_sendpage, or
- * pipe_to_user.
+ * This function loops over the pipe and calls @actor to do the
+ * actual moving of a single struct pipe_buffer to the desired
+ * destination. It returns when there's no more buffers left in
+ * the pipe or if the requested number of bytes (@sd->total_len)
+ * have been copied. It returns a positive number (one) if the
+ * pipe needs to be filled with more data, zero if the required
+ * number of bytes have been copied and -errno on error.
*
+ * This, together with splice_from_pipe_{begin,end,next}, may be
+ * used to implement the functionality of __splice_from_pipe() when
+ * locking is required around copying the pipe buffers to the
+ * destination.
*/
-ssize_t __splice_from_pipe(struct pipe_inode_info *pipe, struct splice_desc *sd,
- splice_actor *actor)
+int splice_from_pipe_feed(struct pipe_inode_info *pipe, struct splice_desc *sd,
+ splice_actor *actor)
{
- int ret, do_wakeup, err;
-
- ret = 0;
- do_wakeup = 0;
-
- for (;;) {
- if (pipe->nrbufs) {
- struct pipe_buffer *buf = pipe->bufs + pipe->curbuf;
- const struct pipe_buf_operations *ops = buf->ops;
+ int ret;
- sd->len = buf->len;
- if (sd->len > sd->total_len)
- sd->len = sd->total_len;
+ while (pipe->nrbufs) {
+ struct pipe_buffer *buf = pipe->bufs + pipe->curbuf;
+ const struct pipe_buf_operations *ops = buf->ops;
- err = actor(pipe, buf, sd);
- if (err <= 0) {
- if (!ret && err != -ENODATA)
- ret = err;
+ sd->len = buf->len;
+ if (sd->len > sd->total_len)
+ sd->len = sd->total_len;
- break;
- }
+ ret = actor(pipe, buf, sd);
+ if (ret <= 0) {
+ if (ret == -ENODATA)
+ ret = 0;
+ return ret;
+ }
+ buf->offset += ret;
+ buf->len -= ret;
- ret += err;
- buf->offset += err;
- buf->len -= err;
+ sd->num_spliced += ret;
+ sd->len -= ret;
+ sd->pos += ret;
+ sd->total_len -= ret;
- sd->len -= err;
- sd->pos += err;
- sd->total_len -= err;
- if (sd->len)
- continue;
+ if (!buf->len) {
+ buf->ops = NULL;
+ ops->release(pipe, buf);
+ pipe->curbuf = (pipe->curbuf + 1) & (PIPE_BUFFERS - 1);
+ pipe->nrbufs--;
+ if (pipe->inode)
+ sd->need_wakeup = true;
+ }
- if (!buf->len) {
- buf->ops = NULL;
- ops->release(pipe, buf);
- pipe->curbuf = (pipe->curbuf + 1) & (PIPE_BUFFERS - 1);
- pipe->nrbufs--;
- if (pipe->inode)
- do_wakeup = 1;
- }
+ if (!sd->total_len)
+ return 0;
+ }
- if (!sd->total_len)
- break;
- }
+ return 1;
+}
+EXPORT_SYMBOL(splice_from_pipe_feed);
- if (pipe->nrbufs)
- continue;
+/**
+ * splice_from_pipe_next - wait for some data to splice from
+ * @pipe: pipe to splice from
+ * @sd: information about the splice operation
+ *
+ * Description:
+ * This function will wait for some data and return a positive
+ * value (one) if pipe buffers are available. It will return zero
+ * or -errno if no more data needs to be spliced.
+ */
+int splice_from_pipe_next(struct pipe_inode_info *pipe, struct splice_desc *sd)
+{
+ while (!pipe->nrbufs) {
if (!pipe->writers)
- break;
- if (!pipe->waiting_writers) {
- if (ret)
- break;
- }
+ return 0;
- if (sd->flags & SPLICE_F_NONBLOCK) {
- if (!ret)
- ret = -EAGAIN;
- break;
- }
+ if (!pipe->waiting_writers && sd->num_spliced)
+ return 0;
- if (signal_pending(current)) {
- if (!ret)
- ret = -ERESTARTSYS;
- break;
- }
+ if (sd->flags & SPLICE_F_NONBLOCK)
+ return -EAGAIN;
- if (do_wakeup) {
- smp_mb();
- if (waitqueue_active(&pipe->wait))
- wake_up_interruptible_sync(&pipe->wait);
- kill_fasync(&pipe->fasync_writers, SIGIO, POLL_OUT);
- do_wakeup = 0;
+ if (signal_pending(current))
+ return -ERESTARTSYS;
+
+ if (sd->need_wakeup) {
+ wakeup_pipe_writers(pipe);
+ sd->need_wakeup = false;
}
pipe_wait(pipe);
}
- if (do_wakeup) {
- smp_mb();
- if (waitqueue_active(&pipe->wait))
- wake_up_interruptible(&pipe->wait);
- kill_fasync(&pipe->fasync_writers, SIGIO, POLL_OUT);
- }
+ return 1;
+}
+EXPORT_SYMBOL(splice_from_pipe_next);
- return ret;
+/**
+ * splice_from_pipe_begin - start splicing from pipe
+ * @sd: information about the splice operation
+ *
+ * Description:
+ * This function should be called before a loop containing
+ * splice_from_pipe_next() and splice_from_pipe_feed() to
+ * initialize the necessary fields of @sd.
+ */
+void splice_from_pipe_begin(struct splice_desc *sd)
+{
+ sd->num_spliced = 0;
+ sd->need_wakeup = false;
+}
+EXPORT_SYMBOL(splice_from_pipe_begin);
+
+/**
+ * splice_from_pipe_end - finish splicing from pipe
+ * @pipe: pipe to splice from
+ * @sd: information about the splice operation
+ *
+ * Description:
+ * This function will wake up pipe writers if necessary. It should
+ * be called after a loop containing splice_from_pipe_next() and
+ * splice_from_pipe_feed().
+ */
+void splice_from_pipe_end(struct pipe_inode_info *pipe, struct splice_desc *sd)
+{
+ if (sd->need_wakeup)
+ wakeup_pipe_writers(pipe);
+}
+EXPORT_SYMBOL(splice_from_pipe_end);
+
+/**
+ * __splice_from_pipe - splice data from a pipe to given actor
+ * @pipe: pipe to splice from
+ * @sd: information to @actor
+ * @actor: handler that splices the data
+ *
+ * Description:
+ * This function does little more than loop over the pipe and call
+ * @actor to do the actual moving of a single struct pipe_buffer to
+ * the desired destination. See pipe_to_file, pipe_to_sendpage, or
+ * pipe_to_user.
+ *
+ */
+ssize_t __splice_from_pipe(struct pipe_inode_info *pipe, struct splice_desc *sd,
+ splice_actor *actor)
+{
+ int ret;
+
+ splice_from_pipe_begin(sd);
+ do {
+ ret = splice_from_pipe_next(pipe, sd);
+ if (ret > 0)
+ ret = splice_from_pipe_feed(pipe, sd, actor);
+ } while (ret > 0);
+ splice_from_pipe_end(pipe, sd);
+
+ return sd->num_spliced ? sd->num_spliced : ret;
}
EXPORT_SYMBOL(__splice_from_pipe);
* @actor: handler that splices the data
*
* Description:
- * See __splice_from_pipe. This function locks the input and output inodes,
+ * See __splice_from_pipe. This function locks the pipe inode,
* otherwise it's identical to __splice_from_pipe().
*
*/
splice_actor *actor)
{
ssize_t ret;
- struct inode *inode = out->f_mapping->host;
struct splice_desc sd = {
.total_len = len,
.flags = flags,
.u.file = out,
};
- /*
- * The actor worker might be calling ->write_begin and
- * ->write_end. Most of the time, these expect i_mutex to
- * be held. Since this may result in an ABBA deadlock with
- * pipe->inode, we have to order lock acquiry here.
- *
- * Outer lock must be inode->i_mutex, as pipe_wait() will
- * release and reacquire pipe->inode->i_mutex, AND inode must
- * never be a pipe.
- */
- WARN_ON(S_ISFIFO(inode->i_mode));
- mutex_lock_nested(&inode->i_mutex, I_MUTEX_PARENT);
- if (pipe->inode)
- mutex_lock_nested(&pipe->inode->i_mutex, I_MUTEX_CHILD);
+ pipe_lock(pipe);
ret = __splice_from_pipe(pipe, &sd, actor);
- if (pipe->inode)
- mutex_unlock(&pipe->inode->i_mutex);
- mutex_unlock(&inode->i_mutex);
+ pipe_unlock(pipe);
return ret;
}
/**
- * generic_file_splice_write_nolock - generic_file_splice_write without mutexes
+ * generic_file_splice_write - splice data from a pipe to a file
* @pipe: pipe info
* @out: file to write to
* @ppos: position in @out
*
* Description:
* Will either move or copy pages (determined by @flags options) from
- * the given pipe inode to the given file. The caller is responsible
- * for acquiring i_mutex on both inodes.
+ * the given pipe inode to the given file.
*
*/
ssize_t
-generic_file_splice_write_nolock(struct pipe_inode_info *pipe, struct file *out,
- loff_t *ppos, size_t len, unsigned int flags)
+generic_file_splice_write(struct pipe_inode_info *pipe, struct file *out,
+ loff_t *ppos, size_t len, unsigned int flags)
{
struct address_space *mapping = out->f_mapping;
struct inode *inode = mapping->host;
.u.file = out,
};
ssize_t ret;
- int err;
-
- err = file_remove_suid(out);
- if (unlikely(err))
- return err;
-
- ret = __splice_from_pipe(pipe, &sd, pipe_to_file);
- if (ret > 0) {
- unsigned long nr_pages;
- *ppos += ret;
- nr_pages = (ret + PAGE_CACHE_SIZE - 1) >> PAGE_CACHE_SHIFT;
-
- /*
- * If file or inode is SYNC and we actually wrote some data,
- * sync it.
- */
- if (unlikely((out->f_flags & O_SYNC) || IS_SYNC(inode))) {
- err = generic_osync_inode(inode, mapping,
- OSYNC_METADATA|OSYNC_DATA);
+ pipe_lock(pipe);
- if (err)
- ret = err;
- }
- balance_dirty_pages_ratelimited_nr(mapping, nr_pages);
- }
+ splice_from_pipe_begin(&sd);
+ do {
+ ret = splice_from_pipe_next(pipe, &sd);
+ if (ret <= 0)
+ break;
- return ret;
-}
+ mutex_lock_nested(&inode->i_mutex, I_MUTEX_CHILD);
+ ret = file_remove_suid(out);
+ if (!ret)
+ ret = splice_from_pipe_feed(pipe, &sd, pipe_to_file);
+ mutex_unlock(&inode->i_mutex);
+ } while (ret > 0);
+ splice_from_pipe_end(pipe, &sd);
-EXPORT_SYMBOL(generic_file_splice_write_nolock);
+ pipe_unlock(pipe);
-/**
- * generic_file_splice_write - splice data from a pipe to a file
- * @pipe: pipe info
- * @out: file to write to
- * @ppos: position in @out
- * @len: number of bytes to splice
- * @flags: splice modifier flags
- *
- * Description:
- * Will either move or copy pages (determined by @flags options) from
- * the given pipe inode to the given file.
- *
- */
-ssize_t
-generic_file_splice_write(struct pipe_inode_info *pipe, struct file *out,
- loff_t *ppos, size_t len, unsigned int flags)
-{
- struct address_space *mapping = out->f_mapping;
- struct inode *inode = mapping->host;
- struct splice_desc sd = {
- .total_len = len,
- .flags = flags,
- .pos = *ppos,
- .u.file = out,
- };
- ssize_t ret;
+ if (sd.num_spliced)
+ ret = sd.num_spliced;
- WARN_ON(S_ISFIFO(inode->i_mode));
- mutex_lock_nested(&inode->i_mutex, I_MUTEX_PARENT);
- ret = file_remove_suid(out);
- if (likely(!ret)) {
- if (pipe->inode)
- mutex_lock_nested(&pipe->inode->i_mutex, I_MUTEX_CHILD);
- ret = __splice_from_pipe(pipe, &sd, pipe_to_file);
- if (pipe->inode)
- mutex_unlock(&pipe->inode->i_mutex);
- }
- mutex_unlock(&inode->i_mutex);
if (ret > 0) {
unsigned long nr_pages;
if (!pipe)
return -EBADF;
- if (pipe->inode)
- mutex_lock(&pipe->inode->i_mutex);
+ pipe_lock(pipe);
error = ret = 0;
while (nr_segs) {
iov++;
}
- if (pipe->inode)
- mutex_unlock(&pipe->inode->i_mutex);
+ pipe_unlock(pipe);
if (!ret)
ret = error;
return 0;
ret = 0;
- mutex_lock(&pipe->inode->i_mutex);
+ pipe_lock(pipe);
while (!pipe->nrbufs) {
if (signal_pending(current)) {
pipe_wait(pipe);
}
- mutex_unlock(&pipe->inode->i_mutex);
+ pipe_unlock(pipe);
return ret;
}
return 0;
ret = 0;
- mutex_lock(&pipe->inode->i_mutex);
+ pipe_lock(pipe);
while (pipe->nrbufs >= PIPE_BUFFERS) {
if (!pipe->readers) {
pipe->waiting_writers--;
}
- mutex_unlock(&pipe->inode->i_mutex);
+ pipe_unlock(pipe);
return ret;
}
/*
* Potential ABBA deadlock, work around it by ordering lock
- * grabbing by inode address. Otherwise two different processes
+ * grabbing by pipe info address. Otherwise two different processes
* could deadlock (one doing tee from A -> B, the other from B -> A).
*/
- inode_double_lock(ipipe->inode, opipe->inode);
+ pipe_double_lock(ipipe, opipe);
do {
if (!opipe->readers) {
if (!ret && ipipe->waiting_writers && (flags & SPLICE_F_NONBLOCK))
ret = -EAGAIN;
- inode_double_unlock(ipipe->inode, opipe->inode);
+ pipe_unlock(ipipe);
+ pipe_unlock(opipe);
/*
* If we put data in the output pipe, wakeup any potential readers.
if (buffer->event != atomic_read(&od->event))
goto trigger;
- return 0;
+ return DEFAULT_POLLMASK;
trigger:
buffer->needs_read_fill = 1;
- return POLLERR|POLLPRI;
+ return DEFAULT_POLLMASK|POLLERR|POLLPRI;
}
void sysfs_notify_dirent(struct sysfs_dirent *sd)
struct work_struct work;
};
+static struct workqueue_struct *sysfs_workqueue;
static DEFINE_MUTEX(sysfs_workq_mutex);
static LIST_HEAD(sysfs_workq);
static void sysfs_schedule_callback_work(struct work_struct *work)
mutex_lock(&sysfs_workq_mutex);
list_for_each_entry_safe(ss, tmp, &sysfs_workq, workq_list)
if (ss->kobj == kobj) {
+ module_put(owner);
mutex_unlock(&sysfs_workq_mutex);
return -EAGAIN;
}
mutex_unlock(&sysfs_workq_mutex);
+ if (sysfs_workqueue == NULL) {
+ sysfs_workqueue = create_workqueue("sysfsd");
+ if (sysfs_workqueue == NULL) {
+ module_put(owner);
+ return -ENOMEM;
+ }
+ }
+
ss = kmalloc(sizeof(*ss), GFP_KERNEL);
if (!ss) {
module_put(owner);
mutex_lock(&sysfs_workq_mutex);
list_add_tail(&ss->workq_list, &sysfs_workq);
mutex_unlock(&sysfs_workq_mutex);
- schedule_work(&ss->work);
+ queue_work(sysfs_workqueue, &ss->work);
return 0;
}
EXPORT_SYMBOL_GPL(sysfs_schedule_callback);
+++ /dev/null
-arch
-mach-types.h
#else /* !CONFIG_BUG */
#ifndef HAVE_ARCH_BUG
-#define BUG()
+#define BUG() do {} while(0)
#endif
#ifndef HAVE_ARCH_BUG_ON
return bio && bio->bi_io_vec != NULL;
}
+/*
+ * BIO list managment for use by remapping drivers (e.g. DM or MD).
+ *
+ * A bio_list anchors a singly-linked list of bios chained through the bi_next
+ * member of the bio. The bio_list also caches the last list member to allow
+ * fast access to the tail.
+ */
+struct bio_list {
+ struct bio *head;
+ struct bio *tail;
+};
+
+static inline int bio_list_empty(const struct bio_list *bl)
+{
+ return bl->head == NULL;
+}
+
+static inline void bio_list_init(struct bio_list *bl)
+{
+ bl->head = bl->tail = NULL;
+}
+
+#define bio_list_for_each(bio, bl) \
+ for (bio = (bl)->head; bio; bio = bio->bi_next)
+
+static inline unsigned bio_list_size(const struct bio_list *bl)
+{
+ unsigned sz = 0;
+ struct bio *bio;
+
+ bio_list_for_each(bio, bl)
+ sz++;
+
+ return sz;
+}
+
+static inline void bio_list_add(struct bio_list *bl, struct bio *bio)
+{
+ bio->bi_next = NULL;
+
+ if (bl->tail)
+ bl->tail->bi_next = bio;
+ else
+ bl->head = bio;
+
+ bl->tail = bio;
+}
+
+static inline void bio_list_add_head(struct bio_list *bl, struct bio *bio)
+{
+ bio->bi_next = bl->head;
+
+ bl->head = bio;
+
+ if (!bl->tail)
+ bl->tail = bio;
+}
+
+static inline void bio_list_merge(struct bio_list *bl, struct bio_list *bl2)
+{
+ if (!bl2->head)
+ return;
+
+ if (bl->tail)
+ bl->tail->bi_next = bl2->head;
+ else
+ bl->head = bl2->head;
+
+ bl->tail = bl2->tail;
+}
+
+static inline void bio_list_merge_head(struct bio_list *bl,
+ struct bio_list *bl2)
+{
+ if (!bl2->head)
+ return;
+
+ if (bl->head)
+ bl2->tail->bi_next = bl->head;
+ else
+ bl->tail = bl2->tail;
+
+ bl->head = bl2->head;
+}
+
+static inline struct bio *bio_list_pop(struct bio_list *bl)
+{
+ struct bio *bio = bl->head;
+
+ if (bio) {
+ bl->head = bl->head->bi_next;
+ if (!bl->head)
+ bl->tail = NULL;
+
+ bio->bi_next = NULL;
+ }
+
+ return bio;
+}
+
+static inline struct bio *bio_list_get(struct bio_list *bl)
+{
+ struct bio *bio = bl->head;
+
+ bl->head = bl->tail = NULL;
+
+ return bio;
+}
+
#if defined(CONFIG_BLK_DEV_INTEGRITY)
#define bip_vec_idx(bip, idx) (&(bip->bip_vec[(idx)]))
unsigned long b_state);
void end_buffer_read_sync(struct buffer_head *bh, int uptodate);
void end_buffer_write_sync(struct buffer_head *bh, int uptodate);
+void end_buffer_async_write(struct buffer_head *bh, int uptodate);
/* Things to do with buffers at mapping->private_list */
void mark_buffer_dirty_inode(struct buffer_head *bh, struct inode *inode);
void block_invalidatepage(struct page *page, unsigned long offset);
int block_write_full_page(struct page *page, get_block_t *get_block,
struct writeback_control *wbc);
+int block_write_full_page_endio(struct page *page, get_block_t *get_block,
+ struct writeback_control *wbc, bh_end_io_t *handler);
int block_read_full_page(struct page*, get_block_t*);
int block_is_partially_uptodate(struct page *page, read_descriptor_t *desc,
unsigned long from);
DEBUG_HASH2, __LINE__, _DPRINTK_FLAGS_DEFAULT }; \
if (__dynamic_dbg_enabled(descriptor)) \
dev_printk(KERN_DEBUG, dev, \
- KBUILD_MODNAME ": " pr_fmt(fmt),\
+ KBUILD_MODNAME ": " fmt, \
##__VA_ARGS__); \
} while (0)
*/
#define FMODE_NOCMTIME ((__force fmode_t)2048)
+/*
+ * The below are the various read and write types that we support. Some of
+ * them include behavioral modifiers that send information down to the
+ * block layer and IO scheduler. Terminology:
+ *
+ * The block layer uses device plugging to defer IO a little bit, in
+ * the hope that we will see more IO very shortly. This increases
+ * coalescing of adjacent IO and thus reduces the number of IOs we
+ * have to send to the device. It also allows for better queuing,
+ * if the IO isn't mergeable. If the caller is going to be waiting
+ * for the IO, then he must ensure that the device is unplugged so
+ * that the IO is dispatched to the driver.
+ *
+ * All IO is handled async in Linux. This is fine for background
+ * writes, but for reads or writes that someone waits for completion
+ * on, we want to notify the block layer and IO scheduler so that they
+ * know about it. That allows them to make better scheduling
+ * decisions. So when the below references 'sync' and 'async', it
+ * is referencing this priority hint.
+ *
+ * With that in mind, the available types are:
+ *
+ * READ A normal read operation. Device will be plugged.
+ * READ_SYNC A synchronous read. Device is not plugged, caller can
+ * immediately wait on this read without caring about
+ * unplugging.
+ * READA Used for read-ahead operations. Lower priority, and the
+ * block layer could (in theory) choose to ignore this
+ * request if it runs into resource problems.
+ * WRITE A normal async write. Device will be plugged.
+ * SWRITE Like WRITE, but a special case for ll_rw_block() that
+ * tells it to lock the buffer first. Normally a buffer
+ * must be locked before doing IO.
+ * WRITE_SYNC_PLUG Synchronous write. Identical to WRITE, but passes down
+ * the hint that someone will be waiting on this IO
+ * shortly. The device must still be unplugged explicitly,
+ * WRITE_SYNC_PLUG does not do this as we could be
+ * submitting more writes before we actually wait on any
+ * of them.
+ * WRITE_SYNC Like WRITE_SYNC_PLUG, but also unplugs the device
+ * immediately after submission. The write equivalent
+ * of READ_SYNC.
+ * WRITE_ODIRECT Special case write for O_DIRECT only.
+ * SWRITE_SYNC
+ * SWRITE_SYNC_PLUG Like WRITE_SYNC/WRITE_SYNC_PLUG, but locks the buffer.
+ * See SWRITE.
+ * WRITE_BARRIER Like WRITE, but tells the block layer that all
+ * previously submitted writes must be safely on storage
+ * before this one is started. Also guarantees that when
+ * this write is complete, it itself is also safely on
+ * storage. Prevents reordering of writes on both sides
+ * of this IO.
+ *
+ */
#define RW_MASK 1
#define RWA_MASK 2
#define READ 0
(SWRITE | (1 << BIO_RW_SYNCIO) | (1 << BIO_RW_NOIDLE))
#define SWRITE_SYNC (SWRITE_SYNC_PLUG | (1 << BIO_RW_UNPLUG))
#define WRITE_BARRIER (WRITE | (1 << BIO_RW_BARRIER))
+
+/*
+ * These aren't really reads or writes, they pass down information about
+ * parts of device that are now unused by the file system.
+ */
#define DISCARD_NOBARRIER (1 << BIO_RW_DISCARD)
#define DISCARD_BARRIER ((1 << BIO_RW_DISCARD) | (1 << BIO_RW_BARRIER))
I_MUTEX_QUOTA
};
-extern void inode_double_lock(struct inode *inode1, struct inode *inode2);
-extern void inode_double_unlock(struct inode *inode1, struct inode *inode2);
-
/*
* NOTE: in a 32bit arch with a preemptable kernel and
* an UP compile the i_size_read/write must be atomic
struct pipe_inode_info *, size_t, unsigned int);
extern ssize_t generic_file_splice_write(struct pipe_inode_info *,
struct file *, loff_t *, size_t, unsigned int);
-extern ssize_t generic_file_splice_write_nolock(struct pipe_inode_info *,
- struct file *, loff_t *, size_t, unsigned int);
extern ssize_t generic_splice_sendpage(struct pipe_inode_info *pipe,
struct file *out, loff_t *, size_t len, unsigned int flags);
extern long do_splice_direct(struct file *in, loff_t *ppos, struct file *out,
*
*/
-/* Flags related to I2C device features */
-#define FSL_I2C_DEV_SEPARATE_DFSRR 0x00000001
-#define FSL_I2C_DEV_CLOCK_5200 0x00000002
-
enum fsl_usb2_operating_modes {
FSL_USB2_MPH_HOST,
FSL_USB2_DR_HOST,
/* Relies on boot_command_line being set */
void __init parse_early_param(void);
+void __init parse_early_options(char *cmdline);
#endif /* __ASSEMBLY__ */
/**
#define pr_cont(fmt, ...) \
printk(KERN_CONT fmt, ##__VA_ARGS__)
+/* pr_devel() should produce zero code unless DEBUG is defined */
+#ifdef DEBUG
+#define pr_devel(fmt, ...) \
+ printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
+#else
+#define pr_devel(fmt, ...) \
+ ({ if (0) printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__); 0; })
+#endif
+
/* If you are writing a driver, please use dev_dbg instead */
#if defined(DEBUG)
#define pr_debug(fmt, ...) \
/* bits 24:31 of ap->flags are reserved for LLD specific flags */
+
/* struct ata_port pflags */
ATA_PFLAG_EH_PENDING = (1 << 0), /* EH pending */
ATA_PFLAG_EH_IN_PROGRESS = (1 << 1), /* EH in progress */
ATA_PFLAG_PM_PENDING = (1 << 18), /* PM operation pending */
ATA_PFLAG_INIT_GTM_VALID = (1 << 19), /* initial gtm data valid */
+ ATA_PFLAG_PIO32 = (1 << 20), /* 32bit PIO */
+ ATA_PFLAG_PIO32CHANGE = (1 << 21), /* 32bit PIO can be turned on/off */
+
/* struct ata_queued_cmd flags */
ATA_QCFLAG_ACTIVE = (1 << 0), /* cmd not yet ack'd to scsi lyer */
ATA_QCFLAG_DMAMAP = (1 << 1), /* SG table is DMA mapped */
struct Scsi_Host *scsi_host; /* our co-allocated scsi host */
struct ata_port_operations *ops;
spinlock_t *lock;
+ /* Flags owned by the EH context. Only EH should touch these once the
+ port is active */
unsigned long flags; /* ATA_FLAG_xxx */
+ /* Flags that change dynamically, protected by ap->lock */
unsigned int pflags; /* ATA_PFLAG_xxx */
unsigned int print_id; /* user visible unique port ID */
unsigned int port_no; /* 0 based port no. inside the host */
extern void ata_sff_error_handler(struct ata_port *ap);
extern void ata_sff_post_internal_cmd(struct ata_queued_cmd *qc);
extern int ata_sff_port_start(struct ata_port *ap);
+extern int ata_sff_port_start32(struct ata_port *ap);
extern void ata_sff_std_ports(struct ata_ioports *ioaddr);
extern unsigned long ata_bmdma_mode_filter(struct ata_device *dev,
unsigned long xfer_mask);
/* Enables or disables interrupts */
int (*config_intr)(struct phy_device *phydev);
+ /*
+ * Checks if the PHY generated an interrupt.
+ * For multi-PHY devices with shared PHY interrupt pin
+ */
+ int (*did_interrupt)(struct phy_device *phydev);
+
/* Clears up any memory if needed */
void (*remove)(struct phy_device *phydev);
memory allocation, whereas PIPE_BUF makes atomicity guarantees. */
#define PIPE_SIZE PAGE_SIZE
+/* Pipe lock and unlock operations */
+void pipe_lock(struct pipe_inode_info *);
+void pipe_unlock(struct pipe_inode_info *);
+void pipe_double_lock(struct pipe_inode_info *, struct pipe_inode_info *);
+
/* Drop the inode semaphore and wait for a pipe event, atomically */
void pipe_wait(struct pipe_inode_info *pipe);
#define platform_get_drvdata(_dev) dev_get_drvdata(&(_dev)->dev)
#define platform_set_drvdata(_dev,data) dev_set_drvdata(&(_dev)->dev, (data))
+/* early platform driver interface */
+struct early_platform_driver {
+ const char *class_str;
+ struct platform_driver *pdrv;
+ struct list_head list;
+ int requested_id;
+};
+
+#define EARLY_PLATFORM_ID_UNSET -2
+#define EARLY_PLATFORM_ID_ERROR -3
+
+extern int early_platform_driver_register(struct early_platform_driver *epdrv,
+ char *buf);
+extern void early_platform_add_devices(struct platform_device **devs, int num);
+
+static inline int is_early_platform_device(struct platform_device *pdev)
+{
+ return !pdev->dev.driver;
+}
+
+extern void early_platform_driver_register_all(char *class_str);
+extern int early_platform_driver_probe(char *class_str,
+ int nr_probe, int user_only);
+extern void early_platform_cleanup(void);
+
+
+#ifndef MODULE
+#define early_platform_init(class_string, platform_driver) \
+static __initdata struct early_platform_driver early_driver = { \
+ .class_str = class_string, \
+ .pdrv = platform_driver, \
+ .requested_id = EARLY_PLATFORM_ID_UNSET, \
+}; \
+static int __init early_platform_driver_setup_func(char *buf) \
+{ \
+ return early_platform_driver_register(&early_driver, buf); \
+} \
+early_param(class_string, early_platform_driver_setup_func)
+#else /* MODULE */
+#define early_platform_init(class_string, platform_driver)
+#endif /* MODULE */
+
#endif /* _PLATFORM_DEVICE_H_ */
unsigned long offline_fqs; /* Kicked due to being offline. */
unsigned long resched_ipi; /* Sent a resched IPI. */
- /* 5) state to allow this CPU to force_quiescent_state on others */
+ /* 5) For future __rcu_pending statistics. */
long n_rcu_pending; /* rcu_pending() calls since boot. */
- long n_rcu_pending_force_qs; /* when to force quiescent states. */
int cpu;
};
#else /* CONFIG_SECCOMP */
+#include <linux/errno.h>
+
typedef struct { } seccomp_t;
#define secure_computing(x) do { } while (0)
void **filter_data);
int (*filter) (void *filter_data, int data_idx, int *val);
void (*filter_cleanup)(void *filter_data);
+ void (*wait_for_sync)(void);
};
void *data; /* cookie */
} u;
loff_t pos; /* file position */
+ size_t num_spliced; /* number of bytes already spliced */
+ bool need_wakeup; /* need to wake up writer */
};
struct partial_page {
splice_actor *);
extern ssize_t __splice_from_pipe(struct pipe_inode_info *,
struct splice_desc *, splice_actor *);
+extern int splice_from_pipe_feed(struct pipe_inode_info *, struct splice_desc *,
+ splice_actor *);
+extern int splice_from_pipe_next(struct pipe_inode_info *,
+ struct splice_desc *);
+extern void splice_from_pipe_begin(struct splice_desc *);
+extern void splice_from_pipe_end(struct pipe_inode_info *,
+ struct splice_desc *);
+extern int pipe_to_file(struct pipe_inode_info *, struct pipe_buffer *,
+ struct splice_desc *);
+
extern ssize_t splice_to_pipe(struct pipe_inode_info *,
struct splice_pipe_desc *);
extern ssize_t splice_direct_to_actor(struct file *, struct splice_desc *,
extern int usb_clear_halt(struct usb_device *dev, int pipe);
extern int usb_reset_configuration(struct usb_device *dev);
extern int usb_set_interface(struct usb_device *dev, int ifnum, int alternate);
+extern void usb_reset_endpoint(struct usb_device *dev, unsigned int epaddr);
/* this request isn't really synchronous, but it belongs with the others */
extern int usb_driver_set_configuration(struct usb_device *udev, int config);
#define usb_pipecontrol(pipe) (usb_pipetype((pipe)) == PIPE_CONTROL)
#define usb_pipebulk(pipe) (usb_pipetype((pipe)) == PIPE_BULK)
-/* The D0/D1 toggle bits ... USE WITH CAUTION (they're almost hcd-internal) */
-#define usb_gettoggle(dev, ep, out) (((dev)->toggle[out] >> (ep)) & 1)
-#define usb_dotoggle(dev, ep, out) ((dev)->toggle[out] ^= (1 << (ep)))
-#define usb_settoggle(dev, ep, out, bit) \
- ((dev)->toggle[out] = ((dev)->toggle[out] & ~(1 << (ep))) | \
- ((bit) << (ep)))
-
-
static inline unsigned int __create_pipe(struct usb_device *dev,
unsigned int endpoint)
{
sk_common_release(sk);
}
-extern int ipv4_rcv_saddr_equal(const struct sock *sk1,
- const struct sock *sk2);
extern int udp_lib_get_port(struct sock *sk, unsigned short snum,
int (*)(const struct sock*,const struct sock*));
int type;
const char *id;
char name[100];
+ void *private_data;
+ void (*private_free)(struct snd_jack *);
};
#ifdef CONFIG_SND_JACK
int overrange;
snd_pcm_uframes_t avail_max;
snd_pcm_uframes_t hw_ptr_base; /* Position at buffer restart */
- snd_pcm_uframes_t hw_ptr_interrupt; /* Position at interrupt time*/
+ snd_pcm_uframes_t hw_ptr_interrupt; /* Position at interrupt time */
+ unsigned long hw_ptr_jiffies; /* Time when hw_ptr is updated */
/* -- HW params -- */
snd_pcm_access_t access; /* access mode */
return 0;
}
+void __init parse_early_options(char *cmdline)
+{
+ parse_args("early options", cmdline, NULL, 0, do_early_param);
+}
+
/* Arch code calls this early on, or if not, just before other parsing. */
void __init parse_early_param(void)
{
/* All fall through to do_early_param. */
strlcpy(tmp_cmdline, boot_command_line, COMMAND_LINE_SIZE);
- parse_args("early options", tmp_cmdline, NULL, 0, do_early_param);
+ parse_early_options(tmp_cmdline);
done = 1;
}
struct bio *bio;
bio = bio_alloc(__GFP_WAIT | __GFP_HIGH, 1);
- if (!bio)
- return -ENOMEM;
bio->bi_sector = page_off * (PAGE_SIZE >> 9);
bio->bi_bdev = resume_bdev;
bio->bi_end_io = end_swap_bio_read;
static struct completion rcu_barrier_completion;
int rcu_scheduler_active __read_mostly;
+static atomic_t rcu_migrate_type_count = ATOMIC_INIT(0);
+static struct rcu_head rcu_migrate_head[3];
+static DECLARE_WAIT_QUEUE_HEAD(rcu_migrate_wq);
+
/*
* Awaken the corresponding synchronize_rcu() instance now that a
* grace period has elapsed.
}
}
-static inline void wait_migrated_callbacks(void);
+static inline void wait_migrated_callbacks(void)
+{
+ wait_event(rcu_migrate_wq, !atomic_read(&rcu_migrate_type_count));
+}
/*
* Orchestrate the specified type of RCU barrier, waiting for all
}
EXPORT_SYMBOL_GPL(rcu_barrier_sched);
-static atomic_t rcu_migrate_type_count = ATOMIC_INIT(0);
-static struct rcu_head rcu_migrate_head[3];
-static DECLARE_WAIT_QUEUE_HEAD(rcu_migrate_wq);
-
static void rcu_migrate_callback(struct rcu_head *notused)
{
if (atomic_dec_and_test(&rcu_migrate_type_count))
wake_up(&rcu_migrate_wq);
}
-static inline void wait_migrated_callbacks(void)
-{
- wait_event(rcu_migrate_wq, !atomic_read(&rcu_migrate_type_count));
-}
-
static int __cpuinit rcu_barrier_cpu_hotplug(struct notifier_block *self,
unsigned long action, void *hcpu)
{
rdp->qs_pending = 1;
rdp->passed_quiesc = 0;
rdp->gpnum = rsp->gpnum;
- rdp->n_rcu_pending_force_qs = rdp->n_rcu_pending +
- RCU_JIFFIES_TILL_FORCE_QS;
}
/*
rsp->gpnum++;
rsp->signaled = RCU_GP_INIT; /* Hold off force_quiescent_state. */
rsp->jiffies_force_qs = jiffies + RCU_JIFFIES_TILL_FORCE_QS;
- rdp->n_rcu_pending_force_qs = rdp->n_rcu_pending +
- RCU_JIFFIES_TILL_FORCE_QS;
record_gp_stall_check_time(rsp);
dyntick_record_completed(rsp, rsp->completed - 1);
note_new_gpnum(rsp, rdp);
{
unsigned long flags;
long lastcomp;
- struct rcu_data *rdp = rsp->rda[smp_processor_id()];
struct rcu_node *rnp = rcu_get_root(rsp);
u8 signaled;
return; /* Someone else is already on the job. */
}
if (relaxed &&
- (long)(rsp->jiffies_force_qs - jiffies) >= 0 &&
- (rdp->n_rcu_pending_force_qs - rdp->n_rcu_pending) >= 0)
+ (long)(rsp->jiffies_force_qs - jiffies) >= 0)
goto unlock_ret; /* no emergency and done recently. */
rsp->n_force_qs++;
spin_lock(&rnp->lock);
lastcomp = rsp->completed;
signaled = rsp->signaled;
rsp->jiffies_force_qs = jiffies + RCU_JIFFIES_TILL_FORCE_QS;
- rdp->n_rcu_pending_force_qs = rdp->n_rcu_pending +
- RCU_JIFFIES_TILL_FORCE_QS;
if (lastcomp == rsp->gpnum) {
rsp->n_force_qs_ngp++;
spin_unlock(&rnp->lock);
* If an RCU GP has gone long enough, go check for dyntick
* idle CPUs and, if needed, send resched IPIs.
*/
- if ((long)(ACCESS_ONCE(rsp->jiffies_force_qs) - jiffies) < 0 ||
- (rdp->n_rcu_pending_force_qs - rdp->n_rcu_pending) < 0)
+ if ((long)(ACCESS_ONCE(rsp->jiffies_force_qs) - jiffies) < 0)
force_quiescent_state(rsp, 1);
/*
if (unlikely(++rdp->qlen > qhimark)) {
rdp->blimit = LONG_MAX;
force_quiescent_state(rsp, 0);
- } else if ((long)(ACCESS_ONCE(rsp->jiffies_force_qs) - jiffies) < 0 ||
- (rdp->n_rcu_pending_force_qs - rdp->n_rcu_pending) < 0)
+ } else if ((long)(ACCESS_ONCE(rsp->jiffies_force_qs) - jiffies) < 0)
force_quiescent_state(rsp, 1);
local_irq_restore(flags);
}
/* Has an RCU GP gone long enough to send resched IPIs &c? */
if (ACCESS_ONCE(rsp->completed) != ACCESS_ONCE(rsp->gpnum) &&
- ((long)(ACCESS_ONCE(rsp->jiffies_force_qs) - jiffies) < 0 ||
- (rdp->n_rcu_pending_force_qs - rdp->n_rcu_pending) < 0))
+ ((long)(ACCESS_ONCE(rsp->jiffies_force_qs) - jiffies) < 0))
return 1;
/* nothing to do */
{
if (!rdp->beenonline)
return;
- seq_printf(m, "%3d%cc=%ld g=%ld pq=%d pqc=%ld qp=%d rpfq=%ld rp=%x",
+ seq_printf(m, "%3d%cc=%ld g=%ld pq=%d pqc=%ld qp=%d",
rdp->cpu,
cpu_is_offline(rdp->cpu) ? '!' : ' ',
rdp->completed, rdp->gpnum,
rdp->passed_quiesc, rdp->passed_quiesc_completed,
- rdp->qs_pending,
- rdp->n_rcu_pending_force_qs - rdp->n_rcu_pending,
- (int)(rdp->n_rcu_pending & 0xffff));
+ rdp->qs_pending);
#ifdef CONFIG_NO_HZ
seq_printf(m, " dt=%d/%d dn=%d df=%lu",
rdp->dynticks->dynticks,
{
if (!rdp->beenonline)
return;
- seq_printf(m, "%d,%s,%ld,%ld,%d,%ld,%d,%ld,%ld",
+ seq_printf(m, "%d,%s,%ld,%ld,%d,%ld,%d",
rdp->cpu,
cpu_is_offline(rdp->cpu) ? "\"Y\"" : "\"N\"",
rdp->completed, rdp->gpnum,
rdp->passed_quiesc, rdp->passed_quiesc_completed,
- rdp->qs_pending,
- rdp->n_rcu_pending_force_qs - rdp->n_rcu_pending,
- rdp->n_rcu_pending);
+ rdp->qs_pending);
#ifdef CONFIG_NO_HZ
seq_printf(m, ",%d,%d,%d,%lu",
rdp->dynticks->dynticks,
static int show_rcudata_csv(struct seq_file *m, void *unused)
{
- seq_puts(m, "\"CPU\",\"Online?\",\"c\",\"g\",\"pq\",\"pqc\",\"pq\",\"rpfq\",\"rp\",");
+ seq_puts(m, "\"CPU\",\"Online?\",\"c\",\"g\",\"pq\",\"pqc\",\"pq\",");
#ifdef CONFIG_NO_HZ
seq_puts(m, "\"dt\",\"dt nesting\",\"dn\",\"df\",");
#endif /* #ifdef CONFIG_NO_HZ */
res->end = end;
res->flags = IORESOURCE_BUSY;
- for (;;) {
- conflict = __request_resource(parent, res);
- if (!conflict)
- break;
- if (conflict != parent) {
- parent = conflict;
- if (!(conflict->flags & IORESOURCE_BUSY))
- continue;
- }
-
- /* Uhhuh, that didn't work out.. */
- kfree(res);
- res = NULL;
- break;
- }
-
- if (!res) {
- /* failed, split and try again */
-
- /* conflict covered whole area */
- if (conflict->start <= start && conflict->end >= end)
- return;
+ conflict = __request_resource(parent, res);
+ if (!conflict)
+ return;
- if (conflict->start > start)
- __reserve_region_with_split(root, start, conflict->start-1, name);
- if (!(conflict->flags & IORESOURCE_BUSY)) {
- resource_size_t common_start, common_end;
+ /* failed, split and try again */
+ kfree(res);
- common_start = max(conflict->start, start);
- common_end = min(conflict->end, end);
- if (common_start < common_end)
- __reserve_region_with_split(root, common_start, common_end, name);
- }
- if (conflict->end < end)
- __reserve_region_with_split(root, conflict->end+1, end, name);
- }
+ /* conflict covered whole area */
+ if (conflict->start <= start && conflict->end >= end)
+ return;
+ if (conflict->start > start)
+ __reserve_region_with_split(root, start, conflict->start-1, name);
+ if (conflict->end < end)
+ __reserve_region_with_split(root, conflict->end+1, end, name);
}
void __init reserve_region_with_split(struct resource *root,
#endif
}
-unsigned long get_parent_ip(unsigned long addr)
+notrace unsigned long get_parent_ip(unsigned long addr)
{
if (in_lock_functions(addr)) {
addr = CALLER_ADDR2;
cpumask_or(groupmask, groupmask, sched_group_cpus(group));
cpulist_scnprintf(str, sizeof(str), sched_group_cpus(group));
- printk(KERN_CONT " %s (__cpu_power = %d)", str,
- group->__cpu_power);
+
+ printk(KERN_CONT " %s", str);
+ if (group->__cpu_power != SCHED_LOAD_SCALE) {
+ printk(KERN_CONT " (__cpu_power = %d)",
+ group->__cpu_power);
+ }
group = group->next;
} while (group != sd->groups);
printk("Attempt to kill tasklet from interrupt\n");
while (test_and_set_bit(TASKLET_STATE_SCHED, &t->state)) {
- do
+ do {
yield();
- while (test_bit(TASKLET_STATE_SCHED, &t->state));
+ } while (test_bit(TASKLET_STATE_SCHED, &t->state));
}
tasklet_unlock_wait(t);
clear_bit(TASKLET_STATE_SCHED, &t->state);
return TRACE_TYPE_HANDLED;
}
+static void branch_print_header(struct seq_file *s)
+{
+ seq_puts(s, "# TASK-PID CPU# TIMESTAMP CORRECT"
+ " FUNC:FILE:LINE\n");
+ seq_puts(s, "# | | | | | "
+ " |\n");
+}
static struct trace_event trace_branch_event = {
.type = TRACE_BRANCH,
#ifdef CONFIG_FTRACE_SELFTEST
.selftest = trace_selftest_startup_branch,
#endif /* CONFIG_FTRACE_SELFTEST */
+ .print_header = branch_print_header,
};
__init static int init_branch_tracer(void)
return TRACE_TYPE_UNHANDLED;
}
+static void power_print_header(struct seq_file *s)
+{
+ seq_puts(s, "# TIMESTAMP STATE EVENT\n");
+ seq_puts(s, "# | | |\n");
+}
+
static struct tracer power_tracer __read_mostly =
{
.name = "power",
.stop = stop_power_trace,
.reset = power_trace_reset,
.print_line = power_print_line,
+ .print_header = power_print_header,
};
static int init_power_trace(void)
goto exit;
retval = call_usermodehelper(argv[0], argv,
- env->envp, UMH_NO_WAIT);
+ env->envp, UMH_WAIT_EXEC);
}
exit:
"kobject_uevent: unable to create netlink socket!\n");
return -ENODEV;
}
-
+ netlink_set_nonroot(NETLINK_KOBJECT_UEVENT, NL_NONROOT_RECV);
return 0;
}
}
return err;
}
+EXPORT_SYMBOL(filemap_write_and_wait_range);
/**
* add_to_page_cache_locked - add a locked page to the pagecache
* Overcommit.. This must be the final test, as it will
* update security statistics.
*/
- if (security_vm_enough_memory(grow))
+ if (security_vm_enough_memory_mm(mm, grow))
return -ENOMEM;
/* Ok, everything looks good - let it rip */
nr_reclaimed += shrink_list(l, nr_to_scan, zone,
sc, prio);
if (nr_reclaimed >= nr_pages) {
- sc->nr_reclaimed = nr_reclaimed;
+ sc->nr_reclaimed += nr_reclaimed;
return;
}
}
}
}
- sc->nr_reclaimed = nr_reclaimed;
+ sc->nr_reclaimed += nr_reclaimed;
}
/*
.may_unmap = 0,
.may_writepage = 1,
.isolate_pages = isolate_pages_global,
+ .nr_reclaimed = 0,
};
current->reclaim_state = &reclaim_state;
}
seq_putc(seq, '\n');
}
+
+ if (dev)
+ dev_put(dev);
}
return 0;
}
if (!skb)
return NET_RX_DROP;
- if (netpoll_rx_on(skb))
+ if (netpoll_rx_on(skb)) {
+ skb->protocol = eth_type_trans(skb, skb->dev);
return vlan_hwaccel_receive_skb(skb, grp, vlan_tci);
+ }
return napi_frags_finish(napi, skb,
vlan_gro_common(napi, grp, vlan_tci, skb));
{
if (test_and_clear_bit(__LINK_STATE_PRESENT, &dev->state) &&
netif_running(dev)) {
- netif_stop_queue(dev);
+ netif_tx_stop_all_queues(dev);
}
}
EXPORT_SYMBOL(netif_device_detach);
{
if (!test_and_set_bit(__LINK_STATE_PRESENT, &dev->state) &&
netif_running(dev)) {
- netif_wake_queue(dev);
+ netif_tx_wake_all_queues(dev);
__netdev_watchdog_up(dev);
}
}
struct list_head *head = &ptype_base[ntohs(type) & PTYPE_HASH_MASK];
int err = -ENOENT;
- if (NAPI_GRO_CB(skb)->count == 1)
+ if (NAPI_GRO_CB(skb)->count == 1) {
+ skb_shinfo(skb)->gso_size = 0;
goto out;
+ }
rcu_read_lock();
list_for_each_entry_rcu(ptype, head, list) {
}
out:
- skb_shinfo(skb)->gso_size = 0;
return netif_receive_skb(skb);
}
tcp_set_rto(sk);
if (inet_csk(sk)->icsk_rto < TCP_TIMEOUT_INIT && !tp->rx_opt.saw_tstamp)
goto reset;
+
+cwnd:
tp->snd_cwnd = tcp_init_cwnd(tp, dst);
tp->snd_cwnd_stamp = tcp_time_stamp;
return;
tp->mdev = tp->mdev_max = tp->rttvar = TCP_TIMEOUT_INIT;
inet_csk(sk)->icsk_rto = TCP_TIMEOUT_INIT;
}
+ goto cwnd;
}
static void tcp_update_reordering(struct sock *sk, const int metric,
return error;
}
-int ipv4_rcv_saddr_equal(const struct sock *sk1, const struct sock *sk2)
+static int ipv4_rcv_saddr_equal(const struct sock *sk1, const struct sock *sk2)
{
struct inet_sock *inet1 = inet_sk(sk1), *inet2 = inet_sk(sk2);
EXPORT_SYMBOL(udp_lib_setsockopt);
EXPORT_SYMBOL(udp_poll);
EXPORT_SYMBOL(udp_lib_get_port);
-EXPORT_SYMBOL(ipv4_rcv_saddr_equal);
#ifdef CONFIG_PROC_FS
EXPORT_SYMBOL(udp_proc_register);
default:
goto sticky_done;
}
-
- if ((rthdr->hdrlen & 1) ||
- (rthdr->hdrlen >> 1) != rthdr->segments_left)
- goto sticky_done;
}
retv = 0;
{
const struct in6_addr *sk_rcv_saddr6 = &inet6_sk(sk)->rcv_saddr;
const struct in6_addr *sk2_rcv_saddr6 = inet6_rcv_saddr(sk2);
+ __be32 sk_rcv_saddr = inet_sk(sk)->rcv_saddr;
+ __be32 sk2_rcv_saddr = inet_rcv_saddr(sk2);
int sk_ipv6only = ipv6_only_sock(sk);
int sk2_ipv6only = inet_v6_ipv6only(sk2);
int addr_type = ipv6_addr_type(sk_rcv_saddr6);
/* if both are mapped, treat as IPv4 */
if (addr_type == IPV6_ADDR_MAPPED && addr_type2 == IPV6_ADDR_MAPPED)
- return ipv4_rcv_saddr_equal(sk, sk2);
+ return (!sk2_ipv6only &&
+ (!sk_rcv_saddr || !sk2_rcv_saddr ||
+ sk_rcv_saddr == sk2_rcv_saddr));
if (addr_type2 == IPV6_ADDR_ANY &&
!(sk2_ipv6only && addr_type == IPV6_ADDR_MAPPED))
static inline char *alloc_one_pg_vec_page(unsigned long order)
{
- return (char *) __get_free_pages(GFP_KERNEL | __GFP_COMP | __GFP_ZERO,
- order);
+ gfp_t gfp_flags = GFP_KERNEL | __GFP_COMP | __GFP_ZERO | __GFP_NOWARN;
+
+ return (char *) __get_free_pages(gfp_flags, order);
}
static char **alloc_pg_vec(struct tpacket_req *req, int order)
unsigned char *asmptr;
int n, size, qbit = 0;
- /* ROSE empty frame has no meaning : don't send */
- if (len == 0)
- return 0;
-
if (msg->msg_flags & ~(MSG_DONTWAIT|MSG_EOR|MSG_CMSG_COMPAT))
return -EINVAL;
skb_reset_transport_header(skb);
copied = skb->len;
- /* ROSE empty frame has no meaning : ignore it */
- if (copied == 0) {
- skb_free_datagram(sk, skb);
- return copied;
- }
-
if (copied > size) {
copied = size;
msg->msg_flags |= MSG_TRUNC;
META_COLLECTOR(int_vlan_tag)
{
- unsigned short uninitialized_var(tag);
- if (vlan_get_tag(skb, &tag) < 0)
+ unsigned short tag;
+
+ tag = vlan_tx_tag_get(skb);
+ if (!tag && __vlan_get_tag(skb, &tag))
*err = -1;
else
dst->value = tag;
cppflags-y :=
ldflags-y :=
+subdir-asflags-y :=
+subdir-ccflags-y :=
+
# Read auto.conf if it exists, otherwise ignore
-include include/config/auto.conf
cppflags-y += $(EXTRA_CPPFLAGS)
ldflags-y += $(EXTRA_LDFLAGS)
+#
+# flags that take effect in sub directories
+export KBUILD_SUBDIR_ASFLAGS := $(KBUILD_SUBDIR_ASFLAGS) $(subdir-asflags-y)
+export KBUILD_SUBDIR_CCFLAGS := $(KBUILD_SUBDIR_CCFLAGS) $(subdir-ccflags-y)
+
# Figure out what we need to build from the various variables
# ===========================================================================
debug_flags =
endif
-orig_c_flags = $(KBUILD_CPPFLAGS) $(KBUILD_CFLAGS) \
+orig_c_flags = $(KBUILD_CPPFLAGS) $(KBUILD_CFLAGS) $(KBUILD_SUBDIR_CCFLAGS) \
$(ccflags-y) $(CFLAGS_$(basetarget).o)
_c_flags = $(filter-out $(CFLAGS_REMOVE_$(basetarget).o), $(orig_c_flags))
-_a_flags = $(KBUILD_CPPFLAGS) $(KBUILD_AFLAGS) \
+_a_flags = $(KBUILD_CPPFLAGS) $(KBUILD_AFLAGS) $(KBUILD_SUBDIR_ASFLAGS) \
$(asflags-y) $(AFLAGS_$(basetarget).o)
_cpp_flags = $(KBUILD_CPPFLAGS) $(cppflags-y) $(CPPFLAGS_$(@F))
strcmp(name, XATTR_NAME_SMACKIPOUT) == 0) {
if (!capable(CAP_MAC_ADMIN))
rc = -EPERM;
- /* a label cannot be void and cannot begin with '-' */
- if (size == 0 || (size > 0 && ((char *)value)[0] == '-'))
+ /*
+ * check label validity here so import wont fail on
+ * post_setxattr
+ */
+ if (size == 0 || size >= SMK_LABELLEN ||
+ smk_import(value, size) == NULL)
rc = -EINVAL;
} else
rc = cap_inode_setxattr(dentry, name, value, size, flags);
if (strcmp(name, XATTR_NAME_SMACK))
return;
- if (size >= SMK_LABELLEN)
- return;
-
isp = dentry->d_inode->i_security;
/*
struct onyx {
/* cache registers 65 to 80, they are write-only! */
u8 cache[16];
- struct i2c_client i2c;
+ struct i2c_client *i2c;
struct aoa_codec codec;
u32 initialised:1,
spdif_locked:1,
*value = onyx->cache[reg-FIRSTREGISTER];
return 0;
}
- v = i2c_smbus_read_byte_data(&onyx->i2c, reg);
+ v = i2c_smbus_read_byte_data(onyx->i2c, reg);
if (v < 0)
return -1;
*value = (u8)v;
{
int result;
- result = i2c_smbus_write_byte_data(&onyx->i2c, reg, value);
+ result = i2c_smbus_write_byte_data(onyx->i2c, reg, value);
if (!result)
onyx->cache[reg-FIRSTREGISTER] = value;
return result;
onyx->codec.soundbus_dev->detach_codec(onyx->codec.soundbus_dev, onyx);
}
-static struct i2c_driver onyx_driver;
-
static int onyx_create(struct i2c_adapter *adapter,
struct device_node *node,
int addr)
{
+ struct i2c_board_info info;
+ struct i2c_client *client;
+
+ memset(&info, 0, sizeof(struct i2c_board_info));
+ strlcpy(info.type, "aoa_codec_onyx", I2C_NAME_SIZE);
+ info.addr = addr;
+ info.platform_data = node;
+ client = i2c_new_device(adapter, &info);
+ if (!client)
+ return -ENODEV;
+
+ /*
+ * We know the driver is already loaded, so the device should be
+ * already bound. If not it means binding failed, which suggests
+ * the device doesn't really exist and should be deleted.
+ * Ideally this would be replaced by better checks _before_
+ * instantiating the device.
+ */
+ if (!client->driver) {
+ i2c_unregister_device(client);
+ return -ENODEV;
+ }
+
+ /*
+ * Let i2c-core delete that device on driver removal.
+ * This is safe because i2c-core holds the core_lock mutex for us.
+ */
+ list_add_tail(&client->detected, &client->driver->clients);
+ return 0;
+}
+
+static int onyx_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device_node *node = client->dev.platform_data;
struct onyx *onyx;
u8 dummy;
return -ENOMEM;
mutex_init(&onyx->mutex);
- onyx->i2c.driver = &onyx_driver;
- onyx->i2c.adapter = adapter;
- onyx->i2c.addr = addr & 0x7f;
- strlcpy(onyx->i2c.name, "onyx audio codec", I2C_NAME_SIZE);
-
- if (i2c_attach_client(&onyx->i2c)) {
- printk(KERN_ERR PFX "failed to attach to i2c\n");
- goto fail;
- }
+ onyx->i2c = client;
+ i2c_set_clientdata(client, onyx);
/* we try to read from register ONYX_REG_CONTROL
* to check if the codec is present */
if (onyx_read_register(onyx, ONYX_REG_CONTROL, &dummy) != 0) {
- i2c_detach_client(&onyx->i2c);
printk(KERN_ERR PFX "failed to read control register\n");
goto fail;
}
onyx->codec.node = of_node_get(node);
if (aoa_codec_register(&onyx->codec)) {
- i2c_detach_client(&onyx->i2c);
goto fail;
}
printk(KERN_DEBUG PFX "created and attached onyx instance\n");
return 0;
fail:
+ i2c_set_clientdata(client, NULL);
kfree(onyx);
- return -EINVAL;
+ return -ENODEV;
}
static int onyx_i2c_attach(struct i2c_adapter *adapter)
return onyx_create(adapter, NULL, 0x47);
}
-static int onyx_i2c_detach(struct i2c_client *client)
+static int onyx_i2c_remove(struct i2c_client *client)
{
- struct onyx *onyx = container_of(client, struct onyx, i2c);
- int err;
+ struct onyx *onyx = i2c_get_clientdata(client);
- if ((err = i2c_detach_client(client)))
- return err;
aoa_codec_unregister(&onyx->codec);
of_node_put(onyx->codec.node);
if (onyx->codec_info)
kfree(onyx->codec_info);
+ i2c_set_clientdata(client, onyx);
kfree(onyx);
return 0;
}
+static const struct i2c_device_id onyx_i2c_id[] = {
+ { "aoa_codec_onyx", 0 },
+ { }
+};
+
static struct i2c_driver onyx_driver = {
.driver = {
.name = "aoa_codec_onyx",
.owner = THIS_MODULE,
},
.attach_adapter = onyx_i2c_attach,
- .detach_client = onyx_i2c_detach,
+ .probe = onyx_i2c_probe,
+ .remove = onyx_i2c_remove,
+ .id_table = onyx_i2c_id,
};
static int __init onyx_init(void)
struct tas {
struct aoa_codec codec;
- struct i2c_client i2c;
+ struct i2c_client *i2c;
u32 mute_l:1, mute_r:1 ,
controls_created:1 ,
drc_enabled:1,
static inline int tas_write_reg(struct tas *tas, u8 reg, u8 len, u8 *data)
{
if (len == 1)
- return i2c_smbus_write_byte_data(&tas->i2c, reg, *data);
+ return i2c_smbus_write_byte_data(tas->i2c, reg, *data);
else
- return i2c_smbus_write_i2c_block_data(&tas->i2c, reg, len, data);
+ return i2c_smbus_write_i2c_block_data(tas->i2c, reg, len, data);
}
static void tas3004_set_drc(struct tas *tas)
}
-static struct i2c_driver tas_driver;
-
static int tas_create(struct i2c_adapter *adapter,
struct device_node *node,
int addr)
{
+ struct i2c_board_info info;
+ struct i2c_client *client;
+
+ memset(&info, 0, sizeof(struct i2c_board_info));
+ strlcpy(info.type, "aoa_codec_tas", I2C_NAME_SIZE);
+ info.addr = addr;
+ info.platform_data = node;
+
+ client = i2c_new_device(adapter, &info);
+ if (!client)
+ return -ENODEV;
+
+ /*
+ * Let i2c-core delete that device on driver removal.
+ * This is safe because i2c-core holds the core_lock mutex for us.
+ */
+ list_add_tail(&client->detected, &client->driver->clients);
+ return 0;
+}
+
+static int tas_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device_node *node = client->dev.platform_data;
struct tas *tas;
tas = kzalloc(sizeof(struct tas), GFP_KERNEL);
return -ENOMEM;
mutex_init(&tas->mtx);
- tas->i2c.driver = &tas_driver;
- tas->i2c.adapter = adapter;
- tas->i2c.addr = addr;
+ tas->i2c = client;
+ i2c_set_clientdata(client, tas);
+
/* seems that half is a saner default */
tas->drc_range = TAS3004_DRC_MAX / 2;
- strlcpy(tas->i2c.name, "tas audio codec", I2C_NAME_SIZE);
-
- if (i2c_attach_client(&tas->i2c)) {
- printk(KERN_ERR PFX "failed to attach to i2c\n");
- goto fail;
- }
strlcpy(tas->codec.name, "tas", MAX_CODEC_NAME_LEN);
tas->codec.owner = THIS_MODULE;
tas->codec.node = of_node_get(node);
if (aoa_codec_register(&tas->codec)) {
- goto detach;
+ goto fail;
}
printk(KERN_DEBUG
"snd-aoa-codec-tas: tas found, addr 0x%02x on %s\n",
- addr, node->full_name);
+ (unsigned int)client->addr, node->full_name);
return 0;
- detach:
- i2c_detach_client(&tas->i2c);
fail:
mutex_destroy(&tas->mtx);
kfree(tas);
return -ENODEV;
}
-static int tas_i2c_detach(struct i2c_client *client)
+static int tas_i2c_remove(struct i2c_client *client)
{
- struct tas *tas = container_of(client, struct tas, i2c);
- int err;
+ struct tas *tas = i2c_get_clientdata(client);
u8 tmp = TAS_ACR_ANALOG_PDOWN;
- if ((err = i2c_detach_client(client)))
- return err;
aoa_codec_unregister(&tas->codec);
of_node_put(tas->codec.node);
return 0;
}
+static const struct i2c_device_id tas_i2c_id[] = {
+ { "aoa_codec_tas", 0 },
+ { }
+};
+
static struct i2c_driver tas_driver = {
.driver = {
.name = "aoa_codec_tas",
.owner = THIS_MODULE,
},
.attach_adapter = tas_i2c_attach,
- .detach_client = tas_i2c_detach,
+ .probe = tas_i2c_probe,
+ .remove = tas_i2c_remove,
+ .id_table = tas_i2c_id,
};
static int __init tas_init(void)
{
struct snd_ctl_elem_value *control;
int result;
-
- control = kmalloc(sizeof(*control), GFP_KERNEL);
- if (control == NULL)
- return -ENOMEM;
- if (copy_from_user(control, _control, sizeof(*control))) {
- kfree(control);
- return -EFAULT;
- }
+
+ control = memdup_user(_control, sizeof(*control));
+ if (IS_ERR(control))
+ return PTR_ERR(control);
+
snd_power_lock(card);
result = snd_power_wait(card, SNDRV_CTL_POWER_D0);
if (result >= 0)
struct snd_card *card;
int result;
- control = kmalloc(sizeof(*control), GFP_KERNEL);
- if (control == NULL)
- return -ENOMEM;
- if (copy_from_user(control, _control, sizeof(*control))) {
- kfree(control);
- return -EFAULT;
- }
+ control = memdup_user(_control, sizeof(*control));
+ if (IS_ERR(control))
+ return PTR_ERR(control);
+
card = file->card;
snd_power_lock(card);
result = snd_power_wait(card, SNDRV_CTL_POWER_D0);
if (op_flag > 0) {
if (size > 1024 * 128) /* sane value */
return -EINVAL;
- new_data = kmalloc(size, GFP_KERNEL);
- if (new_data == NULL)
- return -ENOMEM;
- if (copy_from_user(new_data, tlv, size)) {
- kfree(new_data);
- return -EFAULT;
- }
+
+ new_data = memdup_user(tlv, size);
+ if (IS_ERR(new_data))
+ return PTR_ERR(new_data);
change = ue->tlv_data_size != size;
if (!change)
change = memcmp(ue->tlv_data, new_data, size);
{
struct snd_jack *jack = device->device_data;
+ if (jack->private_free)
+ jack->private_free(jack);
+
/* If the input device is registered with the input subsystem
* then we need to use a different deallocator. */
if (jack->registered)
if (! (runtime = substream->runtime))
return -ENOTTY;
- data = kmalloc(sizeof(*data), GFP_KERNEL);
- if (data == NULL)
- return -ENOMEM;
/* only fifo_size is different, so just copy all */
- if (copy_from_user(data, data32, sizeof(*data32))) {
- err = -EFAULT;
- goto error;
- }
+ data = memdup_user(data32, sizeof(*data32));
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
if (refine)
err = snd_pcm_hw_refine(substream, data);
else
{
struct snd_pcm_runtime *runtime = substream->runtime;
snd_pcm_uframes_t pos;
- snd_pcm_uframes_t new_hw_ptr, hw_ptr_interrupt, hw_base;
- snd_pcm_sframes_t delta;
+ snd_pcm_uframes_t old_hw_ptr, new_hw_ptr, hw_ptr_interrupt, hw_base;
+ snd_pcm_sframes_t hdelta, delta;
+ unsigned long jdelta;
+ old_hw_ptr = runtime->status->hw_ptr;
pos = snd_pcm_update_hw_ptr_pos(substream, runtime);
if (pos == SNDRV_PCM_POS_XRUN) {
xrun(substream);
new_hw_ptr = hw_base + pos;
}
}
- if (delta > runtime->period_size) {
+ hdelta = new_hw_ptr - old_hw_ptr;
+ jdelta = jiffies - runtime->hw_ptr_jiffies;
+ if (((hdelta * HZ) / runtime->rate) > jdelta + HZ/100) {
+ delta = jdelta /
+ (((runtime->period_size * HZ) / runtime->rate)
+ + HZ/100);
+ hw_ptr_error(substream,
+ "hw_ptr skipping! [Q] "
+ "(pos=%ld, delta=%ld, period=%ld, "
+ "jdelta=%lu/%lu/%lu)\n",
+ (long)pos, (long)hdelta,
+ (long)runtime->period_size, jdelta,
+ ((hdelta * HZ) / runtime->rate), delta);
+ hw_ptr_interrupt = runtime->hw_ptr_interrupt +
+ runtime->period_size * delta;
+ if (hw_ptr_interrupt >= runtime->boundary)
+ hw_ptr_interrupt -= runtime->boundary;
+ /* rebase to interrupt position */
+ hw_base = new_hw_ptr = hw_ptr_interrupt;
+ /* align hw_base to buffer_size */
+ hw_base -= hw_base % runtime->buffer_size;
+ delta = 0;
+ }
+ if (delta > runtime->period_size + runtime->period_size / 2) {
hw_ptr_error(substream,
"Lost interrupts? "
"(stream=%i, delta=%ld, intr_ptr=%ld)\n",
runtime->hw_ptr_base = hw_base;
runtime->status->hw_ptr = new_hw_ptr;
+ runtime->hw_ptr_jiffies = jiffies;
runtime->hw_ptr_interrupt = hw_ptr_interrupt;
return snd_pcm_update_hw_ptr_post(substream, runtime);
snd_pcm_uframes_t pos;
snd_pcm_uframes_t old_hw_ptr, new_hw_ptr, hw_base;
snd_pcm_sframes_t delta;
+ unsigned long jdelta;
old_hw_ptr = runtime->status->hw_ptr;
pos = snd_pcm_update_hw_ptr_pos(substream, runtime);
new_hw_ptr = hw_base + pos;
delta = new_hw_ptr - old_hw_ptr;
+ jdelta = jiffies - runtime->hw_ptr_jiffies;
if (delta < 0) {
delta += runtime->buffer_size;
if (delta < 0) {
hw_ptr_error(substream,
"Unexpected hw_pointer value [2] "
- "(stream=%i, pos=%ld, old_ptr=%ld)\n",
+ "(stream=%i, pos=%ld, old_ptr=%ld, jdelta=%li)\n",
substream->stream, (long)pos,
- (long)old_hw_ptr);
+ (long)old_hw_ptr, jdelta);
return 0;
}
hw_base += runtime->buffer_size;
hw_base = 0;
new_hw_ptr = hw_base + pos;
}
- if (delta > runtime->period_size && runtime->periods > 1) {
+ if (((delta * HZ) / runtime->rate) > jdelta + HZ/100) {
hw_ptr_error(substream,
"hw_ptr skipping! "
- "(pos=%ld, delta=%ld, period=%ld)\n",
+ "(pos=%ld, delta=%ld, period=%ld, jdelta=%lu/%lu)\n",
(long)pos, (long)delta,
- (long)runtime->period_size);
+ (long)runtime->period_size, jdelta,
+ ((delta * HZ) / runtime->rate));
return 0;
}
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
runtime->hw_ptr_base = hw_base;
runtime->status->hw_ptr = new_hw_ptr;
+ runtime->hw_ptr_jiffies = jiffies;
return snd_pcm_update_hw_ptr_post(substream, runtime);
}
runtime->status->hw_ptr %= runtime->buffer_size;
else
runtime->status->hw_ptr = 0;
+ runtime->hw_ptr_jiffies = jiffies;
snd_pcm_stream_unlock_irqrestore(substream, flags);
return 0;
}
struct snd_pcm_hw_params *params;
int err;
- params = kmalloc(sizeof(*params), GFP_KERNEL);
- if (!params) {
- err = -ENOMEM;
- goto out;
- }
- if (copy_from_user(params, _params, sizeof(*params))) {
- err = -EFAULT;
- goto out;
- }
+ params = memdup_user(_params, sizeof(*params));
+ if (IS_ERR(params))
+ return PTR_ERR(params);
+
err = snd_pcm_hw_refine(substream, params);
if (copy_to_user(_params, params, sizeof(*params))) {
if (!err)
err = -EFAULT;
}
-out:
+
kfree(params);
return err;
}
struct snd_pcm_hw_params *params;
int err;
- params = kmalloc(sizeof(*params), GFP_KERNEL);
- if (!params) {
- err = -ENOMEM;
- goto out;
- }
- if (copy_from_user(params, _params, sizeof(*params))) {
- err = -EFAULT;
- goto out;
- }
+ params = memdup_user(_params, sizeof(*params));
+ if (IS_ERR(params))
+ return PTR_ERR(params);
+
err = snd_pcm_hw_params(substream, params);
if (copy_to_user(_params, params, sizeof(*params))) {
if (!err)
err = -EFAULT;
}
-out:
+
kfree(params);
return err;
}
return -EFAULT;
if (copy_from_user(&xfern, _xfern, sizeof(xfern)))
return -EFAULT;
- bufs = kmalloc(sizeof(void *) * runtime->channels, GFP_KERNEL);
- if (bufs == NULL)
- return -ENOMEM;
- if (copy_from_user(bufs, xfern.bufs, sizeof(void *) * runtime->channels)) {
- kfree(bufs);
- return -EFAULT;
- }
+
+ bufs = memdup_user(xfern.bufs,
+ sizeof(void *) * runtime->channels);
+ if (IS_ERR(bufs))
+ return PTR_ERR(bufs);
result = snd_pcm_lib_writev(substream, bufs, xfern.frames);
kfree(bufs);
__put_user(result, &_xfern->result);
return -EFAULT;
if (copy_from_user(&xfern, _xfern, sizeof(xfern)))
return -EFAULT;
- bufs = kmalloc(sizeof(void *) * runtime->channels, GFP_KERNEL);
- if (bufs == NULL)
- return -ENOMEM;
- if (copy_from_user(bufs, xfern.bufs, sizeof(void *) * runtime->channels)) {
- kfree(bufs);
- return -EFAULT;
- }
+
+ bufs = memdup_user(xfern.bufs,
+ sizeof(void *) * runtime->channels);
+ if (IS_ERR(bufs))
+ return PTR_ERR(bufs);
result = snd_pcm_lib_readv(substream, bufs, xfern.frames);
kfree(bufs);
__put_user(result, &_xfern->result);
int err;
params = kmalloc(sizeof(*params), GFP_KERNEL);
- if (!params) {
- err = -ENOMEM;
- goto out;
- }
- oparams = kmalloc(sizeof(*oparams), GFP_KERNEL);
- if (!oparams) {
- err = -ENOMEM;
- goto out;
- }
+ if (!params)
+ return -ENOMEM;
- if (copy_from_user(oparams, _oparams, sizeof(*oparams))) {
- err = -EFAULT;
+ oparams = memdup_user(_oparams, sizeof(*oparams));
+ if (IS_ERR(oparams)) {
+ err = PTR_ERR(oparams);
goto out;
}
snd_pcm_hw_convert_from_old_params(params, oparams);
if (!err)
err = -EFAULT;
}
+
+ kfree(oparams);
out:
kfree(params);
- kfree(oparams);
return err;
}
int err;
params = kmalloc(sizeof(*params), GFP_KERNEL);
- if (!params) {
- err = -ENOMEM;
- goto out;
- }
- oparams = kmalloc(sizeof(*oparams), GFP_KERNEL);
- if (!oparams) {
- err = -ENOMEM;
- goto out;
- }
- if (copy_from_user(oparams, _oparams, sizeof(*oparams))) {
- err = -EFAULT;
+ if (!params)
+ return -ENOMEM;
+
+ oparams = memdup_user(_oparams, sizeof(*oparams));
+ if (IS_ERR(oparams)) {
+ err = PTR_ERR(oparams);
goto out;
}
snd_pcm_hw_convert_from_old_params(params, oparams);
if (!err)
err = -EFAULT;
}
+
+ kfree(oparams);
out:
kfree(params);
- kfree(oparams);
return err;
}
#endif /* CONFIG_SND_SUPPORT_OLD_API */
struct snd_seq_port_info *data;
mm_segment_t fs;
- data = kmalloc(sizeof(*data), GFP_KERNEL);
- if (! data)
- return -ENOMEM;
+ data = memdup_user(data32, sizeof(*data32));
+ if (IS_ERR(data))
+ return PTR_ERR(data);
- if (copy_from_user(data, data32, sizeof(*data32)) ||
- get_user(data->flags, &data32->flags) ||
+ if (get_user(data->flags, &data32->flags) ||
get_user(data->time_queue, &data32->time_queue))
goto error;
data->kernel = NULL;
struct list_head *p;
int err = 0;
- ginfo = kmalloc(sizeof(*ginfo), GFP_KERNEL);
- if (! ginfo)
- return -ENOMEM;
- if (copy_from_user(ginfo, _ginfo, sizeof(*ginfo))) {
- kfree(ginfo);
- return -EFAULT;
- }
+ ginfo = memdup_user(_ginfo, sizeof(*ginfo));
+ if (IS_ERR(ginfo))
+ return PTR_ERR(ginfo);
+
tid = ginfo->tid;
memset(ginfo, 0, sizeof(*ginfo));
ginfo->tid = tid;
static int snd_sb_csp_load_user(struct snd_sb_csp * p, const unsigned char __user *buf, int size, int load_flags)
{
- int err = -ENOMEM;
- unsigned char *kbuf = kmalloc(size, GFP_KERNEL);
- if (kbuf) {
- if (copy_from_user(kbuf, buf, size))
- err = -EFAULT;
- else
- err = snd_sb_csp_load(p, kbuf, size, load_flags);
- kfree(kbuf);
- }
+ int err;
+ unsigned char *kbuf;
+
+ kbuf = memdup_user(buf, size);
+ if (IS_ERR(kbuf))
+ return PTR_ERR(kbuf);
+
+ err = snd_sb_csp_load(p, kbuf, size, load_flags);
+
+ kfree(kbuf);
return err;
}
"> 512 bytes to FX\n");
return -EIO;
}
- page_data = kmalloc(r.data[2] * sizeof(short), GFP_KERNEL);
- if (!page_data)
- return -ENOMEM;
- if (copy_from_user (page_data,
- (unsigned char __user *) r.data[3],
- r.data[2] * sizeof(short))) {
- kfree(page_data);
- return -EFAULT;
- }
+ page_data = memdup_user((unsigned char __user *)
+ r.data[3],
+ r.data[2] * sizeof(short));
+ if (IS_ERR(page_data))
+ return PTR_ERR(page_data);
pd = page_data;
}
break;
case WFCTL_WFCMD:
- wc = kmalloc(sizeof(*wc), GFP_KERNEL);
- if (! wc)
- return -ENOMEM;
- if (copy_from_user (wc, argp, sizeof (*wc)))
- err = -EFAULT;
- else if (wavefront_synth_control (acard, wc) < 0)
+ wc = memdup_user(argp, sizeof(*wc));
+ if (IS_ERR(wc))
+ return PTR_ERR(wc);
+
+ if (wavefront_synth_control (acard, wc) < 0)
err = -EIO;
else if (copy_to_user (argp, wc, sizeof (*wc)))
err = -EFAULT;
.name = "HP nx6125",
.type = AC97_TUNE_MUTE_LED
},
+ {
+ .subvendor = 0x103c,
+ .subdevice = 0x3091,
+ .name = "unknown HP",
+ .type = AC97_TUNE_MUTE_LED
+ },
{ } /* terminator */
};
case SNDRV_EMU10K1_IOCTL_CODE_POKE:
if (!capable(CAP_SYS_ADMIN))
return -EPERM;
- icode = kmalloc(sizeof(*icode), GFP_KERNEL);
- if (icode == NULL)
- return -ENOMEM;
- if (copy_from_user(icode, argp, sizeof(*icode))) {
- kfree(icode);
- return -EFAULT;
- }
+
+ icode = memdup_user(argp, sizeof(*icode));
+ if (IS_ERR(icode))
+ return PTR_ERR(icode);
res = snd_emu10k1_icode_poke(emu, icode);
kfree(icode);
return res;
case SNDRV_EMU10K1_IOCTL_CODE_PEEK:
- icode = kmalloc(sizeof(*icode), GFP_KERNEL);
- if (icode == NULL)
- return -ENOMEM;
- if (copy_from_user(icode, argp, sizeof(*icode))) {
- kfree(icode);
- return -EFAULT;
- }
+ icode = memdup_user(argp, sizeof(*icode));
+ if (IS_ERR(icode))
+ return PTR_ERR(icode);
res = snd_emu10k1_icode_peek(emu, icode);
if (res == 0 && copy_to_user(argp, icode, sizeof(*icode))) {
kfree(icode);
kfree(icode);
return res;
case SNDRV_EMU10K1_IOCTL_PCM_POKE:
- ipcm = kmalloc(sizeof(*ipcm), GFP_KERNEL);
- if (ipcm == NULL)
- return -ENOMEM;
- if (copy_from_user(ipcm, argp, sizeof(*ipcm))) {
- kfree(ipcm);
- return -EFAULT;
- }
+ ipcm = memdup_user(argp, sizeof(*ipcm));
+ if (IS_ERR(ipcm))
+ return PTR_ERR(ipcm);
res = snd_emu10k1_ipcm_poke(emu, ipcm);
kfree(ipcm);
return res;
case SNDRV_EMU10K1_IOCTL_PCM_PEEK:
- ipcm = kzalloc(sizeof(*ipcm), GFP_KERNEL);
- if (ipcm == NULL)
- return -ENOMEM;
- if (copy_from_user(ipcm, argp, sizeof(*ipcm))) {
- kfree(ipcm);
- return -EFAULT;
- }
+ ipcm = memdup_user(argp, sizeof(*ipcm));
+ if (IS_ERR(ipcm))
+ return PTR_ERR(ipcm);
res = snd_emu10k1_ipcm_peek(emu, ipcm);
if (res == 0 && copy_to_user(argp, ipcm, sizeof(*ipcm))) {
kfree(ipcm);
if (newtime != curtime)
break;
}
- if (count >= 16384)
+ if (count > 16384)
break;
curtime = newtime;
}
*/
static void /*__devinit*/ setup_fg_nodes(struct hda_codec *codec)
{
- int i, total_nodes;
+ int i, total_nodes, function_id;
hda_nid_t nid;
total_nodes = snd_hda_get_sub_nodes(codec, AC_NODE_ROOT, &nid);
for (i = 0; i < total_nodes; i++, nid++) {
- codec->function_id = snd_hda_param_read(codec, nid,
+ function_id = snd_hda_param_read(codec, nid,
AC_PAR_FUNCTION_TYPE) & 0xff;
- switch (codec->function_id) {
+ switch (function_id) {
case AC_GRP_AUDIO_FUNCTION:
codec->afg = nid;
+ codec->function_id = function_id;
break;
case AC_GRP_MODEM_FUNCTION:
codec->mfg = nid;
+ codec->function_id = function_id;
break;
default:
break;
err = bus->ops.command(bus, res);
if (!err) {
struct hda_cache_head *c;
- u32 key = build_cmd_cache_key(nid, verb);
+ u32 key;
+ /* parm may contain the verb stuff for get/set amp */
+ verb = verb | (parm >> 8);
+ parm &= 0xff;
+ key = build_cmd_cache_key(nid, verb);
c = get_alloc_hash(&codec->cmd_cache, key);
if (c)
c->val = parm;
unsigned int period_bytes; /* size of the period in bytes */
unsigned int frags; /* number for period in the play buffer */
unsigned int fifo_size; /* FIFO size */
+ unsigned long start_jiffies; /* start + minimum jiffies */
+ unsigned long min_jiffies; /* minimum jiffies before position is valid */
void __iomem *sd_addr; /* stream descriptor pointer */
unsigned int opened :1;
unsigned int running :1;
unsigned int irq_pending :1;
- unsigned int irq_ignore :1;
+ unsigned int start_flag: 1; /* stream full start flag */
/*
* For VIA:
* A flag to ensure DMA position is 0
struct azx *chip = dev_id;
struct azx_dev *azx_dev;
u32 status;
- int i;
+ int i, ok;
spin_lock(&chip->reg_lock);
azx_sd_writeb(azx_dev, SD_STS, SD_INT_MASK);
if (!azx_dev->substream || !azx_dev->running)
continue;
- /* ignore the first dummy IRQ (due to pos_adj) */
- if (azx_dev->irq_ignore) {
- azx_dev->irq_ignore = 0;
- continue;
- }
/* check whether this IRQ is really acceptable */
- if (azx_position_ok(chip, azx_dev)) {
+ ok = azx_position_ok(chip, azx_dev);
+ if (ok == 1) {
azx_dev->irq_pending = 0;
spin_unlock(&chip->reg_lock);
snd_pcm_period_elapsed(azx_dev->substream);
spin_lock(&chip->reg_lock);
- } else if (chip->bus && chip->bus->workq) {
+ } else if (ok == 0 && chip->bus && chip->bus->workq) {
/* bogus IRQ, process it later */
azx_dev->irq_pending = 1;
queue_work(chip->bus->workq,
bdl = (u32 *)azx_dev->bdl.area;
ofs = 0;
azx_dev->frags = 0;
- azx_dev->irq_ignore = 0;
pos_adj = bdl_pos_adj[chip->dev_index];
if (pos_adj > 0) {
struct snd_pcm_runtime *runtime = substream->runtime;
&bdl, ofs, pos_adj, 1);
if (ofs < 0)
goto error;
- azx_dev->irq_ignore = 1;
}
} else
pos_adj = 0;
while (((val = azx_sd_readb(azx_dev, SD_CTL)) & SD_CTL_STREAM_RESET) &&
--timeout)
;
+
+ /* reset first position - may not be synced with hw at this time */
+ *azx_dev->posbuf = 0;
}
/*
snd_pcm_set_sync(substream);
mutex_unlock(&chip->open_mutex);
- azx_stream_reset(chip, azx_dev);
return 0;
}
unsigned int bufsize, period_bytes, format_val;
int err;
+ azx_stream_reset(chip, azx_dev);
format_val = snd_hda_calc_stream_format(runtime->rate,
runtime->channels,
runtime->format,
return err;
}
+ azx_dev->min_jiffies = (runtime->period_size * HZ) /
+ (runtime->rate * 2);
azx_setup_controller(chip, azx_dev);
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
azx_dev->fifo_size = azx_sd_readw(azx_dev, SD_FIFOSIZE) + 1;
struct azx *chip = apcm->chip;
struct azx_dev *azx_dev;
struct snd_pcm_substream *s;
- int start, nsync = 0, sbits = 0;
+ int rstart = 0, start, nsync = 0, sbits = 0;
int nwait, timeout;
switch (cmd) {
+ case SNDRV_PCM_TRIGGER_START:
+ rstart = 1;
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
case SNDRV_PCM_TRIGGER_RESUME:
- case SNDRV_PCM_TRIGGER_START:
start = 1;
break;
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
if (s->pcm->card != substream->pcm->card)
continue;
azx_dev = get_azx_dev(s);
+ if (rstart) {
+ azx_dev->start_flag = 1;
+ azx_dev->start_jiffies = jiffies + azx_dev->min_jiffies;
+ }
if (start)
azx_stream_start(chip, azx_dev);
else
{
unsigned int pos;
+ if (azx_dev->start_flag &&
+ time_before_eq(jiffies, azx_dev->start_jiffies))
+ return -1; /* bogus (too early) interrupt */
+ azx_dev->start_flag = 0;
+
pos = azx_get_position(chip, azx_dev);
if (chip->position_fix == POS_FIX_AUTO) {
if (!pos) {
spec->input_mux = &ad1884a_laptop_capture_source;
codec->patch_ops.unsol_event = ad1884a_hp_unsol_event;
codec->patch_ops.init = ad1884a_hp_init;
+ /* set the upper-limit for mixer amp to 0dB for avoiding the
+ * possible damage by overloading
+ */
+ snd_hda_override_amp_caps(codec, 0x20, HDA_INPUT,
+ (0x17 << AC_AMPCAP_OFFSET_SHIFT) |
+ (0x17 << AC_AMPCAP_NUM_STEPS_SHIFT) |
+ (0x05 << AC_AMPCAP_STEP_SIZE_SHIFT) |
+ (1 << AC_AMPCAP_MUTE_SHIFT));
break;
case AD1884A_MOBILE:
spec->mixers[0] = ad1884a_mobile_mixers;
}
#ifdef CONFIG_SND_JACK
+static void conexant_free_jack_priv(struct snd_jack *jack)
+{
+ struct conexant_jack *jacks = jack->private_data;
+ jacks->nid = 0;
+ jacks->jack = NULL;
+}
+
static int conexant_add_jack(struct hda_codec *codec,
hda_nid_t nid, int type)
{
struct conexant_spec *spec;
struct conexant_jack *jack;
const char *name;
+ int err;
spec = codec->spec;
snd_array_init(&spec->jacks, sizeof(*jack), 32);
jack->nid = nid;
jack->type = type;
- return snd_jack_new(codec->bus->card, name, type, &jack->jack);
+ err = snd_jack_new(codec->bus->card, name, type, &jack->jack);
+ if (err < 0)
+ return err;
+ jack->jack->private_data = jack;
+ jack->jack->private_free = conexant_free_jack_priv;
+ return 0;
}
static void conexant_report_jack(struct hda_codec *codec, hda_nid_t nid)
if (spec->jacks.list) {
struct conexant_jack *jacks = spec->jacks.list;
int i;
- for (i = 0; i < spec->jacks.used; i++)
- snd_device_free(codec->bus->card, &jacks[i].jack);
+ for (i = 0; i < spec->jacks.used; i++, jacks++) {
+ if (jacks->jack)
+ snd_device_free(codec->bus->card, jacks->jack);
+ }
snd_array_free(&spec->jacks);
}
#endif
ALC663_ASUS_MODE4,
ALC663_ASUS_MODE5,
ALC663_ASUS_MODE6,
+ ALC272_DELL,
+ ALC272_DELL_ZM1,
ALC662_AUTO,
ALC662_MODEL_LAST,
};
SND_PCI_QUIRK_VENDOR(0x1558, "Clevo laptop", ALC883_LAPTOP_EAPD),
SND_PCI_QUIRK(0x15d9, 0x8780, "Supermicro PDSBA", ALC883_3ST_6ch),
SND_PCI_QUIRK(0x161f, 0x2054, "Medion laptop", ALC883_MEDION),
- SND_PCI_QUIRK(0x1734, 0x1107, "FSC AMILO Xi2550",
+ SND_PCI_QUIRK_MASK(0x1734, 0xfff0, 0x1100, "FSC AMILO Xi/Pi25xx",
ALC883_FUJITSU_PI2515),
- SND_PCI_QUIRK(0x1734, 0x1108, "Fujitsu AMILO Pi2515", ALC883_FUJITSU_PI2515),
- SND_PCI_QUIRK(0x1734, 0x113d, "Fujitsu AMILO Xa3530",
+ SND_PCI_QUIRK_MASK(0x1734, 0xfff0, 0x1130, "Fujitsu AMILO Xa35xx",
ALC888_FUJITSU_XA3530),
SND_PCI_QUIRK(0x17aa, 0x101e, "Lenovo 101e", ALC883_LENOVO_101E_2ch),
SND_PCI_QUIRK(0x17aa, 0x2085, "Lenovo NB0763", ALC883_LENOVO_NB0763),
SND_PCI_QUIRK(0x17aa, 0x3bf8, "Quanta FL1", ALC269_QUANTA_FL1),
SND_PCI_QUIRK(0x1043, 0x8330, "ASUS Eeepc P703 P900A",
ALC269_ASUS_EEEPC_P703),
+ SND_PCI_QUIRK(0x1043, 0x1883, "ASUS F81Se", ALC269_ASUS_EEEPC_P703),
+ SND_PCI_QUIRK(0x1043, 0x16a3, "ASUS F5Q", ALC269_ASUS_EEEPC_P703),
+ SND_PCI_QUIRK(0x1043, 0x1723, "ASUS P80", ALC269_ASUS_EEEPC_P703),
+ SND_PCI_QUIRK(0x1043, 0x1773, "ASUS U20A", ALC269_ASUS_EEEPC_P703),
+ SND_PCI_QUIRK(0x1043, 0x1743, "ASUS U80", ALC269_ASUS_EEEPC_P703),
+ SND_PCI_QUIRK(0x1043, 0x1653, "ASUS U50", ALC269_ASUS_EEEPC_P703),
SND_PCI_QUIRK(0x1043, 0x831a, "ASUS Eeepc P901",
ALC269_ASUS_EEEPC_P901),
SND_PCI_QUIRK(0x1043, 0x834a, "ASUS Eeepc S101",
ALC269_ASUS_EEEPC_P901),
+ SND_PCI_QUIRK(0x1043, 0x16e3, "ASUS UX50", ALC269_ASUS_EEEPC_P901),
SND_PCI_QUIRK(0x1734, 0x115d, "FSC Amilo", ALC269_FUJITSU),
SND_PCI_QUIRK(0x10cf, 0x1475, "Lifebook ICH9M-based", ALC269_LIFEBOOK),
{}
0x02, 0x03, 0x04
};
+static hda_nid_t alc272_dac_nids[2] = {
+ 0x02, 0x03
+};
+
static hda_nid_t alc662_adc_nids[1] = {
/* ADC1-2 */
0x09,
};
+static hda_nid_t alc272_adc_nids[1] = {
+ /* ADC1-2 */
+ 0x08,
+};
+
static hda_nid_t alc662_capsrc_nids[1] = { 0x22 };
+static hda_nid_t alc272_capsrc_nids[1] = { 0x23 };
+
/* input MUX */
/* FIXME: should be a matrix-type input source selection */
/* Mixer elements: 0x18, 19, 1a, 1b, 1c, 1d, 14, 15, 16, 17, 0b */
/* Input mixer */
{0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
-
{0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
/* always trun on EAPD */
{0x14, AC_VERB_SET_EAPD_BTLENABLE, 2},
{}
};
+static struct hda_verb alc272_dell_zm1_init_verbs[] = {
+ {0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x21, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
+ {0x21, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x21, AC_VERB_SET_CONNECT_SEL, 0x01}, /* Headphone */
+ {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(9)},
+ {0x18, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC880_MIC_EVENT},
+ {0x21, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC880_HP_EVENT},
+ {}
+};
+
+static struct hda_verb alc272_dell_init_verbs[] = {
+ {0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x21, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
+ {0x21, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x21, AC_VERB_SET_CONNECT_SEL, 0x01}, /* Headphone */
+ {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(9)},
+ {0x18, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC880_MIC_EVENT},
+ {0x21, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC880_HP_EVENT},
+ {}
+};
+
static struct snd_kcontrol_new alc662_auto_capture_mixer[] = {
HDA_CODEC_VOLUME("Capture Volume", 0x09, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Capture Switch", 0x09, 0x0, HDA_INPUT),
{ } /* end */
};
+static struct snd_kcontrol_new alc272_auto_capture_mixer[] = {
+ HDA_CODEC_VOLUME("Capture Volume", 0x08, 0x0, HDA_INPUT),
+ HDA_CODEC_MUTE("Capture Switch", 0x08, 0x0, HDA_INPUT),
+ { } /* end */
+};
+
static void alc662_lenovo_101e_ispeaker_automute(struct hda_codec *codec)
{
unsigned int present;
static struct snd_pci_quirk alc662_cfg_tbl[] = {
SND_PCI_QUIRK(0x1019, 0x9087, "ECS", ALC662_ECS),
+ SND_PCI_QUIRK(0x1028, 0x02d6, "DELL", ALC272_DELL),
+ SND_PCI_QUIRK(0x1028, 0x02f4, "DELL ZM1", ALC272_DELL_ZM1),
SND_PCI_QUIRK(0x1043, 0x1000, "ASUS N50Vm", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x1092, "ASUS NB", ALC663_ASUS_MODE3),
SND_PCI_QUIRK(0x1043, 0x11c3, "ASUS M70V", ALC663_ASUS_MODE3),
SND_PCI_QUIRK(0x1043, 0x1763, "ASUS NB", ALC663_ASUS_MODE6),
SND_PCI_QUIRK(0x1043, 0x1765, "ASUS NB", ALC663_ASUS_MODE6),
SND_PCI_QUIRK(0x1043, 0x1783, "ASUS NB", ALC662_ASUS_MODE2),
+ SND_PCI_QUIRK(0x1043, 0x17b3, "ASUS F70SL", ALC663_ASUS_MODE3),
+ SND_PCI_QUIRK(0x1043, 0x17c3, "ASUS UX20", ALC663_ASUS_M51VA),
+ SND_PCI_QUIRK(0x1043, 0x17f3, "ASUS X58LE", ALC662_ASUS_MODE2),
SND_PCI_QUIRK(0x1043, 0x1813, "ASUS NB", ALC662_ASUS_MODE2),
SND_PCI_QUIRK(0x1043, 0x1823, "ASUS NB", ALC663_ASUS_MODE5),
SND_PCI_QUIRK(0x1043, 0x1833, "ASUS NB", ALC663_ASUS_MODE6),
SND_PCI_QUIRK(0x1043, 0x1843, "ASUS NB", ALC662_ASUS_MODE2),
+ SND_PCI_QUIRK(0x1043, 0x1853, "ASUS F50Z", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x1864, "ASUS NB", ALC662_ASUS_MODE2),
SND_PCI_QUIRK(0x1043, 0x1876, "ASUS NB", ALC662_ASUS_MODE2),
SND_PCI_QUIRK(0x1043, 0x1878, "ASUS M51VA", ALC663_ASUS_M51VA),
/*SND_PCI_QUIRK(0x1043, 0x1878, "ASUS M50Vr", ALC663_ASUS_MODE1),*/
SND_PCI_QUIRK(0x1043, 0x1893, "ASUS M50Vm", ALC663_ASUS_MODE3),
SND_PCI_QUIRK(0x1043, 0x1894, "ASUS X55", ALC663_ASUS_MODE3),
+ SND_PCI_QUIRK(0x1043, 0x18b3, "ASUS N80Vc", ALC663_ASUS_MODE1),
+ SND_PCI_QUIRK(0x1043, 0x18d3, "ASUS N81Te", ALC663_ASUS_MODE1),
+ SND_PCI_QUIRK(0x1043, 0x18f3, "ASUS N505Tp", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x1903, "ASUS F5GL", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x1913, "ASUS NB", ALC662_ASUS_MODE2),
SND_PCI_QUIRK(0x1043, 0x1933, "ASUS F80Q", ALC662_ASUS_MODE2),
+ SND_PCI_QUIRK(0x1043, 0x1943, "ASUS Vx3V", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x1953, "ASUS NB", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x1963, "ASUS X71C", ALC663_ASUS_MODE3),
+ SND_PCI_QUIRK(0x1043, 0x1983, "ASUS N5051A", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x1993, "ASUS N20", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x19a3, "ASUS G50V", ALC663_ASUS_G50V),
/*SND_PCI_QUIRK(0x1043, 0x19a3, "ASUS NB", ALC663_ASUS_MODE1),*/
SND_PCI_QUIRK(0x1043, 0x19b3, "ASUS F7Z", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x19c3, "ASUS F5Z/F6x", ALC662_ASUS_MODE2),
+ SND_PCI_QUIRK(0x1043, 0x19d3, "ASUS NB", ALC663_ASUS_M51VA),
SND_PCI_QUIRK(0x1043, 0x19e3, "ASUS NB", ALC663_ASUS_MODE1),
SND_PCI_QUIRK(0x1043, 0x19f3, "ASUS NB", ALC663_ASUS_MODE4),
SND_PCI_QUIRK(0x1043, 0x8290, "ASUS P5GC-MX", ALC662_3ST_6ch_DIG),
.unsol_event = alc663_mode6_unsol_event,
.init_hook = alc663_mode6_inithook,
},
+ [ALC272_DELL] = {
+ .mixers = { alc663_m51va_mixer },
+ .cap_mixer = alc272_auto_capture_mixer,
+ .init_verbs = { alc662_init_verbs, alc272_dell_init_verbs },
+ .num_dacs = ARRAY_SIZE(alc272_dac_nids),
+ .dac_nids = alc662_dac_nids,
+ .num_channel_mode = ARRAY_SIZE(alc662_3ST_2ch_modes),
+ .adc_nids = alc272_adc_nids,
+ .num_adc_nids = ARRAY_SIZE(alc272_adc_nids),
+ .capsrc_nids = alc272_capsrc_nids,
+ .channel_mode = alc662_3ST_2ch_modes,
+ .input_mux = &alc663_m51va_capture_source,
+ .unsol_event = alc663_m51va_unsol_event,
+ .init_hook = alc663_m51va_inithook,
+ },
+ [ALC272_DELL_ZM1] = {
+ .mixers = { alc663_m51va_mixer },
+ .cap_mixer = alc662_auto_capture_mixer,
+ .init_verbs = { alc662_init_verbs, alc272_dell_zm1_init_verbs },
+ .num_dacs = ARRAY_SIZE(alc272_dac_nids),
+ .dac_nids = alc662_dac_nids,
+ .num_channel_mode = ARRAY_SIZE(alc662_3ST_2ch_modes),
+ .adc_nids = alc662_adc_nids,
+ .num_adc_nids = ARRAY_SIZE(alc662_adc_nids),
+ .capsrc_nids = alc662_capsrc_nids,
+ .channel_mode = alc662_3ST_2ch_modes,
+ .input_mux = &alc663_m51va_capture_source,
+ .unsol_event = alc663_m51va_unsol_event,
+ .init_hook = alc663_m51va_inithook,
+ },
};
unsigned int wid_caps;
for (i = 0; i < num_outs && i < ARRAY_SIZE(chname); i++) {
+ if (type == AUTO_PIN_HP_OUT && !spec->hp_detect) {
+ wid_caps = get_wcaps(codec, pins[i]);
+ if (wid_caps & AC_WCAP_UNSOL_CAP)
+ spec->hp_detect = 1;
+ }
nid = dac_nids[i];
if (!nid)
continue;
err = create_controls_idx(codec, name, idx, nid, 3);
if (err < 0)
return err;
- if (type == AUTO_PIN_HP_OUT && !spec->hp_detect) {
- wid_caps = get_wcaps(codec, pins[i]);
- if (wid_caps & AC_WCAP_UNSOL_CAP)
- spec->hp_detect = 1;
- }
}
}
return 0;
AC_VERB_SET_GPIO_DATA, gpiostate); /* sync */
}
+#ifdef CONFIG_SND_JACK
+static void stac92xx_free_jack_priv(struct snd_jack *jack)
+{
+ struct sigmatel_jack *jacks = jack->private_data;
+ jacks->nid = 0;
+ jacks->jack = NULL;
+}
+#endif
+
static int stac92xx_add_jack(struct hda_codec *codec,
hda_nid_t nid, int type)
{
int def_conf = snd_hda_codec_get_pincfg(codec, nid);
int connectivity = get_defcfg_connect(def_conf);
char name[32];
+ int err;
if (connectivity && connectivity != AC_JACK_PORT_FIXED)
return 0;
snd_hda_get_jack_connectivity(def_conf),
snd_hda_get_jack_location(def_conf));
- return snd_jack_new(codec->bus->card, name, type, &jack->jack);
-#else
- return 0;
+ err = snd_jack_new(codec->bus->card, name, type, &jack->jack);
+ if (err < 0) {
+ jack->nid = 0;
+ return err;
+ }
+ jack->jack->private_data = jack;
+ jack->jack->private_free = stac92xx_free_jack_priv;
#endif
+ return 0;
}
static int stac_add_event(struct sigmatel_spec *spec, hda_nid_t nid,
if (!codec->bus->shutdown && spec->jacks.list) {
struct sigmatel_jack *jacks = spec->jacks.list;
int i;
- for (i = 0; i < spec->jacks.used; i++)
- snd_device_free(codec->bus->card, &jacks[i].jack);
+ for (i = 0; i < spec->jacks.used; i++, jacks++) {
+ if (jacks->jack)
+ snd_device_free(codec->bus->card, jacks->jack);
+ }
}
snd_array_free(&spec->jacks);
#endif
unsigned int fragsize1;
unsigned int position;
unsigned int pos_shift;
+ unsigned int last_pos;
+ unsigned long last_pos_jiffies;
+ unsigned int jiffy_to_bytes;
int frags;
int lvi;
int lvi_frag;
ichdev->suspended = 0;
/* fallthru */
case SNDRV_PCM_TRIGGER_START:
+ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
val = ICH_IOCE | ICH_STARTBM;
+ ichdev->last_pos = ichdev->position;
+ ichdev->last_pos_jiffies = jiffies;
break;
case SNDRV_PCM_TRIGGER_SUSPEND:
ichdev->suspended = 1;
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
val = ICH_IOCE;
break;
- case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
- val = ICH_IOCE | ICH_STARTBM;
- break;
default:
return -EINVAL;
}
ichdev->pos_shift = (runtime->sample_bits > 16) ? 2 : 1;
}
snd_intel8x0_setup_periods(chip, ichdev);
+ ichdev->jiffy_to_bytes = (runtime->rate * 4 * ichdev->pos_shift) / HZ;
return 0;
}
struct intel8x0 *chip = snd_pcm_substream_chip(substream);
struct ichdev *ichdev = get_ichdev(substream);
size_t ptr1, ptr;
- int civ, timeout = 100;
+ int civ, timeout = 10;
unsigned int position;
spin_lock(&chip->reg_lock);
ptr1 == igetword(chip, ichdev->reg_offset + ichdev->roff_picb))
break;
} while (timeout--);
- ptr1 <<= ichdev->pos_shift;
- ptr = ichdev->fragsize1 - ptr1;
- ptr += position;
+ if (ptr1 != 0) {
+ ptr1 <<= ichdev->pos_shift;
+ ptr = ichdev->fragsize1 - ptr1;
+ ptr += position;
+ ichdev->last_pos = ptr;
+ ichdev->last_pos_jiffies = jiffies;
+ } else {
+ ptr1 = jiffies - ichdev->last_pos_jiffies;
+ if (ptr1)
+ ptr1 -= 1;
+ ptr = ichdev->last_pos + ptr1 * ichdev->jiffy_to_bytes;
+ ptr %= ichdev->size;
+ }
spin_unlock(&chip->reg_lock);
if (ptr >= ichdev->size)
return 0;
},
{
.subvendor = 0x1028,
+ .subdevice = 0x016a,
+ .name = "Dell Inspiron 8600", /* STAC9750/51 */
+ .type = AC97_TUNE_HP_ONLY
+ },
+ {
+ .subvendor = 0x1028,
.subdevice = 0x0186,
.name = "Dell Latitude D810", /* cf. Malone #41015 */
.type = AC97_TUNE_HP_MUTE_LED
},
{
.subvendor = 0x103c,
- .subdevice = 0x0934,
- .name = "HP nx8220",
- .type = AC97_TUNE_MUTE_LED
- },
- {
- .subvendor = 0x103c,
.subdevice = 0x129d,
.name = "HP xw8000",
.type = AC97_TUNE_HP_ONLY
struct snd_pcm_substream *subs;
struct ichdev *ichdev;
unsigned long port;
- unsigned long pos, t;
- struct timeval start_time, stop_time;
+ unsigned long pos, pos1, t;
+ int civ, timeout = 1000, attempt = 1;
+ struct timespec start_time, stop_time;
if (chip->ac97_bus->clock != 48000)
return; /* specified in module option */
+ __again:
subs = chip->pcm[0]->streams[0].substream;
if (! subs || subs->dma_buffer.bytes < INTEL8X0_TESTBUF_SIZE) {
snd_printk(KERN_WARNING "no playback buffer allocated - aborting measure ac97 clock\n");
}
ichdev = &chip->ichd[ICHD_PCMOUT];
ichdev->physbuf = subs->dma_buffer.addr;
- ichdev->size = chip->ichd[ICHD_PCMOUT].fragsize = INTEL8X0_TESTBUF_SIZE;
+ ichdev->size = ichdev->fragsize = INTEL8X0_TESTBUF_SIZE;
ichdev->substream = NULL; /* don't process interrupts */
/* set rate */
iputbyte(chip, port + ICH_REG_OFF_CR, ICH_IOCE);
iputdword(chip, ICHREG(ALI_DMACR), 1 << ichdev->ali_slot);
}
- do_gettimeofday(&start_time);
+ do_posix_clock_monotonic_gettime(&start_time);
spin_unlock_irq(&chip->reg_lock);
msleep(50);
spin_lock_irq(&chip->reg_lock);
/* check the position */
- pos = ichdev->fragsize1;
- pos -= igetword(chip, ichdev->reg_offset + ichdev->roff_picb) << ichdev->pos_shift;
- pos += ichdev->position;
+ do {
+ civ = igetbyte(chip, ichdev->reg_offset + ICH_REG_OFF_CIV);
+ pos1 = igetword(chip, ichdev->reg_offset + ichdev->roff_picb);
+ if (pos1 == 0) {
+ udelay(10);
+ continue;
+ }
+ if (civ == igetbyte(chip, ichdev->reg_offset + ICH_REG_OFF_CIV) &&
+ pos1 == igetword(chip, ichdev->reg_offset + ichdev->roff_picb))
+ break;
+ } while (timeout--);
+ if (pos1 == 0) { /* oops, this value is not reliable */
+ pos = 0;
+ } else {
+ pos = ichdev->fragsize1;
+ pos -= pos1 << ichdev->pos_shift;
+ pos += ichdev->position;
+ }
chip->in_measurement = 0;
- do_gettimeofday(&stop_time);
+ do_posix_clock_monotonic_gettime(&stop_time);
/* stop */
if (chip->device_type == DEVICE_ALI) {
iputdword(chip, ICHREG(ALI_DMACR), 1 << (ichdev->ali_slot + 16));
iputbyte(chip, port + ICH_REG_OFF_CR, ICH_RESETREGS);
spin_unlock_irq(&chip->reg_lock);
+ if (pos == 0) {
+ snd_printk(KERN_ERR "intel8x0: measure - unreliable DMA position..\n");
+ __retry:
+ if (attempt < 2) {
+ attempt++;
+ goto __again;
+ }
+ return;
+ }
+
+ pos /= 4;
t = stop_time.tv_sec - start_time.tv_sec;
t *= 1000000;
- t += stop_time.tv_usec - start_time.tv_usec;
- printk(KERN_INFO "%s: measured %lu usecs\n", __func__, t);
+ t += (stop_time.tv_nsec - start_time.tv_nsec) / 1000;
+ printk(KERN_INFO "%s: measured %lu usecs (%lu samples)\n", __func__, t, pos);
if (t == 0) {
- snd_printk(KERN_ERR "?? calculation error..\n");
- return;
+ snd_printk(KERN_ERR "intel8x0: ?? calculation error..\n");
+ goto __retry;
}
- pos = (pos / 4) * 1000;
+ pos *= 1000;
pos = (pos / t) * 1000 + ((pos % t) * 1000) / t;
- if (pos < 40000 || pos >= 60000)
+ if (pos < 40000 || pos >= 60000) {
/* abnormal value. hw problem? */
printk(KERN_INFO "intel8x0: measured clock %ld rejected\n", pos);
+ goto __retry;
+ } else if (pos > 40500 && pos < 41500)
+ /* first exception - 41000Hz reference clock */
+ chip->ac97_bus->clock = 41000;
+ else if (pos > 43600 && pos < 44600)
+ /* second exception - 44100HZ reference clock */
+ chip->ac97_bus->clock = 44100;
else if (pos < 47500 || pos > 48500)
/* not 48000Hz, tuning the clock.. */
chip->ac97_bus->clock = (chip->ac97_bus->clock * 48000) / pos;
static struct pmac_keywest *keywest_ctx;
-static int keywest_attach_adapter(struct i2c_adapter *adapter);
-static int keywest_detach_client(struct i2c_client *client);
-
-struct i2c_driver keywest_driver = {
- .driver = {
- .name = "PMac Keywest Audio",
- },
- .attach_adapter = &keywest_attach_adapter,
- .detach_client = &keywest_detach_client,
-};
-
-
#ifndef i2c_device_name
#define i2c_device_name(x) ((x)->name)
#endif
+static int keywest_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ i2c_set_clientdata(client, keywest_ctx);
+ return 0;
+}
+
+/*
+ * This is kind of a hack, best would be to turn powermac to fixed i2c
+ * bus numbers and declare the sound device as part of platform
+ * initialization
+ */
static int keywest_attach_adapter(struct i2c_adapter *adapter)
{
- int err;
- struct i2c_client *new_client;
+ struct i2c_board_info info;
if (! keywest_ctx)
return -EINVAL;
if (strncmp(i2c_device_name(adapter), "mac-io", 6))
return 0; /* ignored */
- new_client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
- if (! new_client)
- return -ENOMEM;
-
- new_client->addr = keywest_ctx->addr;
- i2c_set_clientdata(new_client, keywest_ctx);
- new_client->adapter = adapter;
- new_client->driver = &keywest_driver;
- new_client->flags = 0;
-
- strcpy(i2c_device_name(new_client), keywest_ctx->name);
- keywest_ctx->client = new_client;
+ memset(&info, 0, sizeof(struct i2c_board_info));
+ strlcpy(info.type, "keywest", I2C_NAME_SIZE);
+ info.addr = keywest_ctx->addr;
+ keywest_ctx->client = i2c_new_device(adapter, &info);
- /* Tell the i2c layer a new client has arrived */
- if (i2c_attach_client(new_client)) {
- snd_printk(KERN_ERR "tumbler: cannot attach i2c client\n");
- err = -ENODEV;
- goto __err;
- }
-
+ /*
+ * Let i2c-core delete that device on driver removal.
+ * This is safe because i2c-core holds the core_lock mutex for us.
+ */
+ list_add_tail(&keywest_ctx->client->detected,
+ &keywest_ctx->client->driver->clients);
return 0;
-
- __err:
- kfree(new_client);
- keywest_ctx->client = NULL;
- return err;
}
-static int keywest_detach_client(struct i2c_client *client)
+static int keywest_remove(struct i2c_client *client)
{
+ i2c_set_clientdata(client, NULL);
if (! keywest_ctx)
return 0;
if (client == keywest_ctx->client)
keywest_ctx->client = NULL;
- i2c_detach_client(client);
- kfree(client);
return 0;
}
+
+static const struct i2c_device_id keywest_i2c_id[] = {
+ { "keywest", 0 },
+ { }
+};
+
+struct i2c_driver keywest_driver = {
+ .driver = {
+ .name = "PMac Keywest Audio",
+ },
+ .attach_adapter = keywest_attach_adapter,
+ .probe = keywest_probe,
+ .remove = keywest_remove,
+ .id_table = keywest_i2c_id,
+};
+
/* exported */
void snd_pmac_keywest_cleanup(struct pmac_keywest *i2c)
{
}
#ifdef CONFIG_PM
-static int wm9705_soc_suspend(struct platform_device *pdev)
+static int wm9705_soc_suspend(struct platform_device *pdev, pm_message_t msg)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
struct snd_soc_codec *codec = socdev->card->codec;
*
* Copyright (C) 2008 Nokia Corporation
*
- * Contact: Jarkko Nikula <jarkko.nikula@nokia.com>
+ * Contact: Jarkko Nikula <jhnikula@gmail.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
module_init(n810_soc_init);
module_exit(n810_soc_exit);
-MODULE_AUTHOR("Jarkko Nikula <jarkko.nikula@nokia.com>");
+MODULE_AUTHOR("Jarkko Nikula <jhnikula@gmail.com>");
MODULE_DESCRIPTION("ALSA SoC Nokia N810");
MODULE_LICENSE("GPL");
*
* Copyright (C) 2008 Nokia Corporation
*
- * Contact: Jarkko Nikula <jarkko.nikula@nokia.com>
+ * Contact: Jarkko Nikula <jhnikula@gmail.com>
+ * Peter Ujfalusi <peter.ujfalusi@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
break;
case SND_SOC_DAIFMT_DSP_B:
regs->srgr2 |= FPER(wlen * channels - 1);
- regs->srgr1 |= FWID(wlen * channels - 2);
+ regs->srgr1 |= FWID(0);
break;
}
{
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
struct omap_mcbsp_reg_cfg *regs = &mcbsp_data->regs;
+ unsigned int temp_fmt = fmt;
if (mcbsp_data->configured)
return 0;
/* 0-bit data delay */
regs->rcr2 |= RDATDLY(0);
regs->xcr2 |= XDATDLY(0);
+ /* Invert FS polarity configuration */
+ temp_fmt ^= SND_SOC_DAIFMT_NB_IF;
break;
default:
/* Unsupported data format */
}
/* Set bit clock (CLKX/CLKR) and FS polarities */
- switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ switch (temp_fmt & SND_SOC_DAIFMT_INV_MASK) {
case SND_SOC_DAIFMT_NB_NF:
/*
* Normal BCLK + FS.
}
module_exit(snd_omap_mcbsp_exit);
-MODULE_AUTHOR("Jarkko Nikula <jarkko.nikula@nokia.com>");
+MODULE_AUTHOR("Jarkko Nikula <jhnikula@gmail.com>");
MODULE_DESCRIPTION("OMAP I2S SoC Interface");
MODULE_LICENSE("GPL");
*
* Copyright (C) 2008 Nokia Corporation
*
- * Contact: Jarkko Nikula <jarkko.nikula@nokia.com>
+ * Contact: Jarkko Nikula <jhnikula@gmail.com>
+ * Peter Ujfalusi <peter.ujfalusi@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
*
* Copyright (C) 2008 Nokia Corporation
*
- * Contact: Jarkko Nikula <jarkko.nikula@nokia.com>
+ * Contact: Jarkko Nikula <jhnikula@gmail.com>
+ * Peter Ujfalusi <peter.ujfalusi@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
}
module_exit(omap_soc_platform_exit);
-MODULE_AUTHOR("Jarkko Nikula <jarkko.nikula@nokia.com>");
+MODULE_AUTHOR("Jarkko Nikula <jhnikula@gmail.com>");
MODULE_DESCRIPTION("OMAP PCM DMA module");
MODULE_LICENSE("GPL");
*
* Copyright (C) 2008 Nokia Corporation
*
- * Contact: Jarkko Nikula <jarkko.nikula@nokia.com>
+ * Contact: Jarkko Nikula <jhnikula@gmail.com>
+ * Peter Ujfalusi <peter.ujfalusi@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
/* Set codec DAI configuration */
err = snd_soc_dai_set_fmt(codec_dai,
SND_SOC_DAIFMT_DSP_B |
- SND_SOC_DAIFMT_NB_IF |
+ SND_SOC_DAIFMT_NB_NF |
SND_SOC_DAIFMT_CBM_CFM);
if (err < 0) {
printk(KERN_ERR "can't set codec DAI configuration\n");
/* Set cpu DAI configuration */
err = snd_soc_dai_set_fmt(cpu_dai,
SND_SOC_DAIFMT_DSP_B |
- SND_SOC_DAIFMT_NB_IF |
+ SND_SOC_DAIFMT_NB_NF |
SND_SOC_DAIFMT_CBM_CFM);
if (err < 0) {
printk(KERN_ERR "can't set cpu DAI configuration\n");
#include <sound/soc.h>
#include <sound/soc-dapm.h>
-#include <mach/pxa-regs.h>
-#include <mach/hardware.h>
#include <mach/magician.h>
#include <asm/mach-types.h>
#include "../codecs/uda1380.h"
* ssp_set_clkdiv - set SSP clock divider
* @div: serial clock rate divider
*/
-static void ssp_set_scr(struct ssp_dev *dev, u32 div)
+static void ssp_set_scr(struct ssp_device *ssp, u32 div)
{
- struct ssp_device *ssp = dev->ssp;
- u32 sscr0 = ssp_read_reg(dev->ssp, SSCR0) & ~SSCR0_SCR;
+ u32 sscr0 = ssp_read_reg(ssp, SSCR0);
+
+ if (cpu_is_pxa25x() && ssp->type == PXA25x_SSP) {
+ sscr0 &= ~0x0000ff00;
+ sscr0 |= ((div - 2)/2) << 8; /* 2..512 */
+ } else {
+ sscr0 &= ~0x000fff00;
+ sscr0 |= (div - 1) << 8; /* 1..4096 */
+ }
+ ssp_write_reg(ssp, SSCR0, sscr0);
+}
+
+/**
+ * ssp_get_clkdiv - get SSP clock divider
+ */
+static u32 ssp_get_scr(struct ssp_device *ssp)
+{
+ u32 sscr0 = ssp_read_reg(ssp, SSCR0);
+ u32 div;
- ssp_write_reg(ssp, SSCR0, (sscr0 | SSCR0_SerClkDiv(div)));
+ if (cpu_is_pxa25x() && ssp->type == PXA25x_SSP)
+ div = ((sscr0 >> 8) & 0xff) * 2 + 2;
+ else
+ div = ((sscr0 >> 8) & 0xfff) + 1;
+ return div;
}
/*
break;
case PXA_SSP_CLK_AUDIO:
priv->sysclk = 0;
- ssp_set_scr(&priv->dev, 1);
+ ssp_set_scr(ssp, 1);
sscr0 |= SSCR0_ACS;
break;
default:
ssp_write_reg(ssp, SSACD, val);
break;
case PXA_SSP_DIV_SCR:
- ssp_set_scr(&priv->dev, div);
+ ssp_set_scr(ssp, div);
break;
default:
return -ENODEV;
case SND_SOC_DAIFMT_I2S:
sspsp = ssp_read_reg(ssp, SSPSP);
- if (((sscr0 & SSCR0_SCR) == SSCR0_SerClkDiv(4)) &&
- (width == 16)) {
+ if ((ssp_get_scr(ssp) == 4) && (width == 16)) {
/* This is a special case where the bitclk is 64fs
* and we're not dealing with 2*32 bits of audio
* samples.
goto err_priv;
}
+ priv->dai_fmt = (unsigned int) -1;
dai->private_data = priv;
return 0;
config SND_S3C24XX_SOC
tristate "SoC Audio for the Samsung S3CXXXX chips"
- depends on ARCH_S3C2410 || ARCH_S3C64XX
+ depends on ARCH_S3C2410
help
Say Y or M if you want to add support for codecs attached to
- the S3C24XX and S3C64XX AC97, I2S or SSP interface. You will
- also need to select the audio interfaces to support below.
+ the S3C24XX AC97 or I2S interfaces. You will also need to
+ select the audio interfaces to support below.
config SND_S3C24XX_SOC_I2S
tristate
break;
}
- s3c_i2sv2_calc_rate(&div, NULL, params_rate(params),
- s3c2412_get_iisclk());
+ s3c_i2sv2_iis_calc_rate(&div, NULL, params_rate(params),
+ s3c2412_get_iisclk());
/* set codec DAI configuration */
ret = snd_soc_dai_set_fmt(codec_dai, SND_SOC_DAIFMT_I2S |
};
/* jive audio machine driver */
-static struct snd_soc_machine snd_soc_machine_jive = {
+static struct snd_soc_card snd_soc_machine_jive = {
.name = "Jive",
+ .platform = &s3c24xx_soc_platform,
.dai_link = &jive_dai,
.num_links = 1,
};
/* jive audio subsystem */
static struct snd_soc_device jive_snd_devdata = {
- .machine = &snd_soc_machine_jive,
- .platform = &s3c24xx_soc_platform,
- .codec_dev = &soc_codec_dev_wm8750_spi,
+ .card = &snd_soc_machine_jive,
+ .codec_dev = &soc_codec_dev_wm8750,
.codec_data = &jive_wm8750_setup,
};
/* default table of all avaialable root fs divisors */
static unsigned int iis_fs_tab[] = { 256, 512, 384, 768 };
-int s3c2412_iis_calc_rate(struct s3c_i2sv2_rate_calc *info,
- unsigned int *fstab,
- unsigned int rate, struct clk *clk)
+int s3c_i2sv2_iis_calc_rate(struct s3c_i2sv2_rate_calc *info,
+ unsigned int *fstab,
+ unsigned int rate, struct clk *clk)
{
unsigned long clkrate = clk_get_rate(clk);
unsigned int div;
return 0;
}
-EXPORT_SYMBOL_GPL(s3c2412_iis_calc_rate);
+EXPORT_SYMBOL_GPL(s3c_i2sv2_iis_calc_rate);
int s3c_i2sv2_probe(struct platform_device *pdev,
struct snd_soc_dai *dai,
int s3c_i2sv2_register_dai(struct snd_soc_dai *dai)
{
- dai->ops.trigger = s3c2412_i2s_trigger;
- dai->ops.hw_params = s3c2412_i2s_hw_params;
- dai->ops.set_fmt = s3c2412_i2s_set_fmt;
- dai->ops.set_clkdiv = s3c2412_i2s_set_clkdiv;
+ struct snd_soc_dai_ops *ops = dai->ops;
+
+ ops->trigger = s3c2412_i2s_trigger;
+ ops->hw_params = s3c2412_i2s_hw_params;
+ ops->set_fmt = s3c2412_i2s_set_fmt;
+ ops->set_clkdiv = s3c2412_i2s_set_clkdiv;
dai->suspend = s3c2412_i2s_suspend;
dai->resume = s3c2412_i2s_resume;
#include <plat/regs-s3c2412-iis.h>
-#include <plat/regs-gpio.h>
#include <plat/audio.h>
+#include <mach/regs-gpio.h>
#include <mach/dma.h>
#include "s3c24xx-pcm.h"
-snd-usb-caiaq-y := caiaq-device.o caiaq-audio.o caiaq-midi.o caiaq-control.o
-snd-usb-caiaq-$(CONFIG_SND_USB_CAIAQ_INPUT) += caiaq-input.o
+snd-usb-caiaq-y := device.o audio.o midi.o control.o
+snd-usb-caiaq-$(CONFIG_SND_USB_CAIAQ_INPUT) += input.o
obj-$(CONFIG_SND_USB_CAIAQ) += snd-usb-caiaq.o
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
+#include <linux/spinlock.h>
#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/interrupt.h>
#include <linux/usb.h>
-#include <linux/spinlock.h>
#include <sound/core.h>
-#include <sound/initval.h>
#include <sound/pcm.h>
-#include <sound/rawmidi.h>
-#include <linux/input.h>
-#include "caiaq-device.h"
-#include "caiaq-audio.h"
+#include "device.h"
+#include "audio.h"
#define N_URBS 32
#define CLOCK_DRIFT_TOLERANCE 5
*/
#include <linux/init.h>
-#include <linux/interrupt.h>
#include <linux/usb.h>
+#include <sound/control.h>
#include <sound/core.h>
-#include <sound/initval.h>
#include <sound/pcm.h>
-#include <sound/rawmidi.h>
-#include <sound/control.h>
-#include <linux/input.h>
-#include "caiaq-device.h"
-#include "caiaq-control.h"
+#include "device.h"
+#include "control.h"
#define CNT_INTVAL 0x10000
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <linux/init.h>
-#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/init.h>
#include <linux/usb.h>
-#include <linux/input.h>
-#include <linux/spinlock.h>
-#include <sound/core.h>
#include <sound/initval.h>
+#include <sound/core.h>
#include <sound/pcm.h>
-#include <sound/rawmidi.h>
-#include <sound/control.h>
-
-#include "caiaq-device.h"
-#include "caiaq-audio.h"
-#include "caiaq-midi.h"
-#include "caiaq-control.h"
-#ifdef CONFIG_SND_USB_CAIAQ_INPUT
-#include "caiaq-input.h"
-#endif
+#include "device.h"
+#include "audio.h"
+#include "midi.h"
+#include "control.h"
+#include "input.h"
MODULE_AUTHOR("Daniel Mack <daniel@caiaq.de>");
MODULE_DESCRIPTION("caiaq USB audio, version 1.3.13");
*/
#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/input.h>
#include <linux/usb.h>
#include <linux/usb/input.h>
-#include <linux/spinlock.h>
-#include <sound/core.h>
-#include <sound/rawmidi.h>
#include <sound/pcm.h>
-#include "caiaq-device.h"
-#include "caiaq-input.h"
+
+#include "device.h"
+#include "input.h"
static unsigned short keycode_ak1[] = { KEY_C, KEY_B, KEY_A };
static unsigned short keycode_rk2[] = { KEY_1, KEY_2, KEY_3, KEY_4,
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/interrupt.h>
#include <linux/usb.h>
-#include <linux/input.h>
-#include <linux/spinlock.h>
-#include <sound/core.h>
#include <sound/rawmidi.h>
+#include <sound/core.h>
#include <sound/pcm.h>
-#include "caiaq-device.h"
-#include "caiaq-midi.h"
-
+#include "device.h"
+#include "midi.h"
static int snd_usb_caiaq_midi_input_open(struct snd_rawmidi_substream *substream)
{
if (cmd != SNDRV_USB_STREAM_IOCTL_SET_PARAMS)
return -ENOTTY;
- cfg = kmalloc(sizeof(*cfg), GFP_KERNEL);
- if (!cfg)
- return -ENOMEM;
+ cfg = memdup_user((void *)arg, sizeof(*cfg));
+ if (IS_ERR(cfg))
+ return PTR_ERR(cfg);
- if (copy_from_user(cfg, (void *)arg, sizeof(*cfg))) {
- err = -EFAULT;
- goto free;
- }
if (cfg->version != USB_STREAM_INTERFACE_VERSION) {
err = -ENXIO;
goto free;
if (access_ok(VERIFY_READ, dsp->image, dsp->length)) {
struct usb_device* dev = priv->chip.dev;
- char *buf = kmalloc(dsp->length, GFP_KERNEL);
- if (!buf)
- return -ENOMEM;
- if (copy_from_user(buf, dsp->image, dsp->length)) {
- kfree(buf);
- return -EFAULT;
- }
+ char *buf;
+
+ buf = memdup_user(dsp->image, dsp->length);
+ if (IS_ERR(buf))
+ return PTR_ERR(buf);
+
err = usb_set_interface(dev, 0, 1);
if (err)
snd_printk(KERN_ERR "usb_set_interface error \n");
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff