Kernel internal timer frequency should be a divisor of 32768,
such as 64 or 128.
+config OMAP_DM_TIMER
+ bool "Use dual-mode timer"
+ default n
+ depends on ARCH_OMAP16XX
+ help
+ Select this option if you want to use OMAP Dual-Mode timers.
+
choice
prompt "Low-level debug console UART"
depends on ARCH_OMAP
endchoice
+config OMAP_SERIAL_WAKE
+ bool "Enable wake-up events for serial ports"
+ depends OMAP_MUX
+ default y
+ help
+ Select this option if you want to have your system wake up
+ to data on the serial RX line. This allows you to wake the
+ system from serial console.
+
endmenu
endif
#
# Common support
-obj-y := common.o dma.o clock.o mux.o gpio.o mcbsp.o usb.o
+obj-y := common.o sram.o sram-fn.o clock.o dma.o mux.o gpio.o mcbsp.o usb.o
obj-m :=
obj-n :=
obj- :=
obj-$(CONFIG_PM) += pm.o sleep.o
obj-$(CONFIG_CPU_FREQ) += cpu-omap.o
+obj-$(CONFIG_OMAP_DM_TIMER) += dmtimer.o
+
#include <asm/arch/usb.h>
#include "clock.h"
+#include "sram.h"
static LIST_HEAD(clocks);
static DECLARE_MUTEX(clocks_sem);
static struct clk armper_ck = {
.name = "armper_ck",
.parent = &ck_dpll1,
- .flags = CLOCK_IN_OMAP730 | CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
RATE_CKCTL,
.enable_reg = ARM_IDLECT2,
.enable_bit = EN_PERCK,
.name = "uart2_ck",
/* Direct from ULPD, no parent */
.rate = 12000000,
- .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | ENABLE_REG_32BIT,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | ENABLE_REG_32BIT |
+ ALWAYS_ENABLED,
.enable_reg = MOD_CONF_CTRL_0,
.enable_bit = 30, /* Chooses between 12MHz and 48MHz */
.set_rate = &set_uart_rate,
.enable_bit = 8 /* UHOST_EN */,
};
+static struct clk usb_dc_ck = {
+ .name = "usb_dc_ck",
+ /* Direct from ULPD, no parent */
+ .rate = 48000000,
+ .flags = CLOCK_IN_OMAP16XX | RATE_FIXED,
+ .enable_reg = SOFT_REQ_REG,
+ .enable_bit = 4,
+};
+
static struct clk mclk_1510 = {
.name = "mclk",
/* Direct from ULPD, no parent. May be enabled by ext hardware. */
&uart3_16xx,
&usb_clko,
&usb_hhc_ck1510, &usb_hhc_ck16xx,
+ &usb_dc_ck,
&mclk_1510, &mclk_16xx,
&bclk_1510, &bclk_16xx,
&mmc1_ck,
if (!ptr->rate)
return -EINVAL;
- if (!ptr->rate)
- return -EINVAL;
+ /*
+ * In most cases we should not need to reprogram DPLL.
+ * Reprogramming the DPLL is tricky, it must be done from SRAM.
+ */
+ omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
- if (unlikely(ck_dpll1.rate == 0)) {
- omap_writew(ptr->dpllctl_val, DPLL_CTL);
- ck_dpll1.rate = ptr->pll_rate;
- }
- omap_writew(ptr->ckctl_val, ARM_CKCTL);
+ ck_dpll1.rate = ptr->pll_rate;
propagate_rate(&ck_dpll1);
return 0;
}
#endif
/* Cache rates for clocks connected to ck_ref (not dpll1) */
propagate_rate(&ck_ref);
- printk(KERN_INFO "Clocking rate (xtal/DPLL1/MPU): %ld.%01ld/%ld/%ld MHz\n",
+ printk(KERN_INFO "Clocking rate (xtal/DPLL1/MPU): "
+ "%ld.%01ld/%ld.%01ld/%ld.%01ld MHz\n",
ck_ref.rate / 1000000, (ck_ref.rate / 100000) % 10,
- ck_dpll1.rate, arm_ck.rate);
+ ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10,
+ arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10);
#ifdef CONFIG_MACH_OMAP_PERSEUS2
/* Select slicer output as OMAP input clock */
struct clk *p;
__u32 regval32;
- omap_writew(0, SOFT_REQ_REG);
+ /* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */
+ regval32 = omap_readw(SOFT_REQ_REG) & (1 << 4);
+ omap_writew(regval32, SOFT_REQ_REG);
omap_writew(0, SOFT_REQ_REG2);
list_for_each_entry(p, &clocks, node) {
#include <asm/hardware/clock.h>
#include <asm/io.h>
#include <asm/mach-types.h>
+#include <asm/setup.h>
#include <asm/arch/board.h>
#include <asm/arch/mux.h>
#define NO_LENGTH_CHECK 0xffffffff
-extern int omap_bootloader_tag_len;
-extern u8 omap_bootloader_tag[];
+unsigned char omap_bootloader_tag[512];
+int omap_bootloader_tag_len;
struct omap_board_config_kernel *omap_board_config;
-int omap_board_config_size = 0;
+int omap_board_config_size;
static const void *get_config(u16 tag, size_t len, int skip, size_t *len_out)
{
dma_chan[ch + 6].saved_csr = csr >> 7;
csr &= 0x7f;
}
- if (!csr)
+ if ((csr & 0x3f) == 0)
return 0;
if (unlikely(dma_chan[ch].dev_id == -1)) {
printk(KERN_WARNING "Spurious interrupt from DMA channel %d (CSR %04x)\n",
w |= 1 << 8;
omap_writew(w, OMAP1610_DMA_LCD_CTRL);
+ lcd_dma.active = 1;
+
w = omap_readw(OMAP1610_DMA_LCD_CCR);
w |= 1 << 7;
omap_writew(w, OMAP1610_DMA_LCD_CCR);
-
- lcd_dma.active = 1;
}
void omap_setup_lcd_dma(void)
*/
dma_addr_t omap_get_dma_src_pos(int lch)
{
- return (dma_addr_t) (OMAP_DMA_CSSA_L(lch) |
- (OMAP_DMA_CSSA_U(lch) << 16));
+ return (dma_addr_t) (omap_readw(OMAP_DMA_CSSA_L(lch)) |
+ (omap_readw(OMAP_DMA_CSSA_U(lch)) << 16));
}
/*
*/
dma_addr_t omap_get_dma_dst_pos(int lch)
{
- return (dma_addr_t) (OMAP_DMA_CDSA_L(lch) |
- (OMAP_DMA_CDSA_U(lch) << 16));
+ return (dma_addr_t) (omap_readw(OMAP_DMA_CDSA_L(lch)) |
+ (omap_readw(OMAP_DMA_CDSA_U(lch)) << 16));
+}
+
+/*
+ * Returns current source transfer counting for the given DMA channel.
+ * Can be used to monitor the progress of a transfer inside a block.
+ * It must be called with disabled interrupts.
+ */
+int omap_get_dma_src_addr_counter(int lch)
+{
+ return (dma_addr_t) omap_readw(OMAP_DMA_CSAC(lch));
}
int omap_dma_running(void)
EXPORT_SYMBOL(omap_get_dma_src_pos);
EXPORT_SYMBOL(omap_get_dma_dst_pos);
+EXPORT_SYMBOL(omap_get_dma_src_addr_counter);
EXPORT_SYMBOL(omap_clear_dma);
EXPORT_SYMBOL(omap_set_dma_priority);
EXPORT_SYMBOL(omap_request_dma);
--- /dev/null
+/*
+ * linux/arch/arm/plat-omap/dmtimer.c
+ *
+ * OMAP Dual-Mode Timers
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Lauri Leukkunen <lauri.leukkunen@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/dmtimer.h>
+#include <asm/io.h>
+#include <asm/arch/irqs.h>
+#include <linux/spinlock.h>
+#include <linux/list.h>
+
+#define OMAP_TIMER_COUNT 8
+
+#define OMAP_TIMER_ID_REG 0x00
+#define OMAP_TIMER_OCP_CFG_REG 0x10
+#define OMAP_TIMER_SYS_STAT_REG 0x14
+#define OMAP_TIMER_STAT_REG 0x18
+#define OMAP_TIMER_INT_EN_REG 0x1c
+#define OMAP_TIMER_WAKEUP_EN_REG 0x20
+#define OMAP_TIMER_CTRL_REG 0x24
+#define OMAP_TIMER_COUNTER_REG 0x28
+#define OMAP_TIMER_LOAD_REG 0x2c
+#define OMAP_TIMER_TRIGGER_REG 0x30
+#define OMAP_TIMER_WRITE_PEND_REG 0x34
+#define OMAP_TIMER_MATCH_REG 0x38
+#define OMAP_TIMER_CAPTURE_REG 0x3c
+#define OMAP_TIMER_IF_CTRL_REG 0x40
+
+
+static struct dmtimer_info_struct {
+ struct list_head unused_timers;
+ struct list_head reserved_timers;
+} dm_timer_info;
+
+static struct omap_dm_timer dm_timers[] = {
+ { .base=0xfffb1400, .irq=INT_1610_GPTIMER1 },
+ { .base=0xfffb1c00, .irq=INT_1610_GPTIMER2 },
+ { .base=0xfffb2400, .irq=INT_1610_GPTIMER3 },
+ { .base=0xfffb2c00, .irq=INT_1610_GPTIMER4 },
+ { .base=0xfffb3400, .irq=INT_1610_GPTIMER5 },
+ { .base=0xfffb3c00, .irq=INT_1610_GPTIMER6 },
+ { .base=0xfffb4400, .irq=INT_1610_GPTIMER7 },
+ { .base=0xfffb4c00, .irq=INT_1610_GPTIMER8 },
+ { .base=0x0 },
+};
+
+
+static spinlock_t dm_timer_lock;
+
+
+inline void omap_dm_timer_write_reg(struct omap_dm_timer *timer, int reg, u32 value)
+{
+ omap_writel(value, timer->base + reg);
+ while (omap_dm_timer_read_reg(timer, OMAP_TIMER_WRITE_PEND_REG))
+ ;
+}
+
+u32 omap_dm_timer_read_reg(struct omap_dm_timer *timer, int reg)
+{
+ return omap_readl(timer->base + reg);
+}
+
+int omap_dm_timers_active(void)
+{
+ struct omap_dm_timer *timer;
+
+ for (timer = &dm_timers[0]; timer->base; ++timer)
+ if (omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG) &
+ OMAP_TIMER_CTRL_ST)
+ return 1;
+
+ return 0;
+}
+
+
+void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source)
+{
+ int n = (timer - dm_timers) << 1;
+ u32 l;
+
+ l = omap_readl(MOD_CONF_CTRL_1) & ~(0x03 << n);
+ l |= source << n;
+ omap_writel(l, MOD_CONF_CTRL_1);
+}
+
+
+static void omap_dm_timer_reset(struct omap_dm_timer *timer)
+{
+ /* Reset and set posted mode */
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_IF_CTRL_REG, 0x06);
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_OCP_CFG_REG, 0x02);
+
+ omap_dm_timer_set_source(timer, OMAP_TIMER_SRC_ARMXOR);
+}
+
+
+
+struct omap_dm_timer * omap_dm_timer_request(void)
+{
+ struct omap_dm_timer *timer = NULL;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dm_timer_lock, flags);
+ if (!list_empty(&dm_timer_info.unused_timers)) {
+ timer = (struct omap_dm_timer *)
+ dm_timer_info.unused_timers.next;
+ list_move_tail((struct list_head *)timer,
+ &dm_timer_info.reserved_timers);
+ }
+ spin_unlock_irqrestore(&dm_timer_lock, flags);
+
+ return timer;
+}
+
+
+void omap_dm_timer_free(struct omap_dm_timer *timer)
+{
+ unsigned long flags;
+
+ omap_dm_timer_reset(timer);
+
+ spin_lock_irqsave(&dm_timer_lock, flags);
+ list_move_tail((struct list_head *)timer, &dm_timer_info.unused_timers);
+ spin_unlock_irqrestore(&dm_timer_lock, flags);
+}
+
+void omap_dm_timer_set_int_enable(struct omap_dm_timer *timer,
+ unsigned int value)
+{
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_INT_EN_REG, value);
+}
+
+unsigned int omap_dm_timer_read_status(struct omap_dm_timer *timer)
+{
+ return omap_dm_timer_read_reg(timer, OMAP_TIMER_STAT_REG);
+}
+
+void omap_dm_timer_write_status(struct omap_dm_timer *timer, unsigned int value)
+{
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_STAT_REG, value);
+}
+
+void omap_dm_timer_enable_autoreload(struct omap_dm_timer *timer)
+{
+ u32 l;
+ l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
+ l |= OMAP_TIMER_CTRL_AR;
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
+}
+
+void omap_dm_timer_trigger(struct omap_dm_timer *timer)
+{
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_TRIGGER_REG, 1);
+}
+
+void omap_dm_timer_set_trigger(struct omap_dm_timer *timer, unsigned int value)
+{
+ u32 l;
+
+ l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
+ l |= value & 0x3;
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
+}
+
+void omap_dm_timer_start(struct omap_dm_timer *timer)
+{
+ u32 l;
+
+ l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
+ l |= OMAP_TIMER_CTRL_ST;
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
+}
+
+void omap_dm_timer_stop(struct omap_dm_timer *timer)
+{
+ u32 l;
+
+ l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
+ l &= ~0x1;
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
+}
+
+unsigned int omap_dm_timer_read_counter(struct omap_dm_timer *timer)
+{
+ return omap_dm_timer_read_reg(timer, OMAP_TIMER_COUNTER_REG);
+}
+
+void omap_dm_timer_reset_counter(struct omap_dm_timer *timer)
+{
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_COUNTER_REG, 0);
+}
+
+void omap_dm_timer_set_load(struct omap_dm_timer *timer, unsigned int load)
+{
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_LOAD_REG, load);
+}
+
+void omap_dm_timer_set_match(struct omap_dm_timer *timer, unsigned int match)
+{
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_MATCH_REG, match);
+}
+
+void omap_dm_timer_enable_compare(struct omap_dm_timer *timer)
+{
+ u32 l;
+
+ l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
+ l |= OMAP_TIMER_CTRL_CE;
+ omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
+}
+
+
+static inline void __dm_timer_init(void)
+{
+ struct omap_dm_timer *timer;
+
+ spin_lock_init(&dm_timer_lock);
+ INIT_LIST_HEAD(&dm_timer_info.unused_timers);
+ INIT_LIST_HEAD(&dm_timer_info.reserved_timers);
+
+ timer = &dm_timers[0];
+ while (timer->base) {
+ list_add_tail((struct list_head *)timer, &dm_timer_info.unused_timers);
+ omap_dm_timer_reset(timer);
+ timer++;
+ }
+}
+
+static int __init omap_dm_timer_init(void)
+{
+ if (cpu_is_omap16xx())
+ __dm_timer_init();
+ return 0;
+}
+
+arch_initcall(omap_dm_timer_init);
*
* Support functions for OMAP GPIO
*
- * Copyright (C) 2003 Nokia Corporation
+ * Copyright (C) 2003-2005 Nokia Corporation
* Written by Juha Yrjölä <juha.yrjola@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
#include <linux/sched.h>
#include <linux/interrupt.h>
#include <linux/ptrace.h>
+#include <linux/sysdev.h>
+#include <linux/err.h>
#include <asm/hardware.h>
+#include <asm/hardware/clock.h>
#include <asm/irq.h>
#include <asm/arch/irqs.h>
#include <asm/arch/gpio.h>
/*
* OMAP1510 GPIO registers
*/
-#define OMAP1510_GPIO_BASE 0xfffce000
+#define OMAP1510_GPIO_BASE (void __iomem *)0xfffce000
#define OMAP1510_GPIO_DATA_INPUT 0x00
#define OMAP1510_GPIO_DATA_OUTPUT 0x04
#define OMAP1510_GPIO_DIR_CONTROL 0x08
/*
* OMAP1610 specific GPIO registers
*/
-#define OMAP1610_GPIO1_BASE 0xfffbe400
-#define OMAP1610_GPIO2_BASE 0xfffbec00
-#define OMAP1610_GPIO3_BASE 0xfffbb400
-#define OMAP1610_GPIO4_BASE 0xfffbbc00
+#define OMAP1610_GPIO1_BASE (void __iomem *)0xfffbe400
+#define OMAP1610_GPIO2_BASE (void __iomem *)0xfffbec00
+#define OMAP1610_GPIO3_BASE (void __iomem *)0xfffbb400
+#define OMAP1610_GPIO4_BASE (void __iomem *)0xfffbbc00
#define OMAP1610_GPIO_REVISION 0x0000
#define OMAP1610_GPIO_SYSCONFIG 0x0010
#define OMAP1610_GPIO_SYSSTATUS 0x0014
#define OMAP1610_GPIO_IRQSTATUS1 0x0018
#define OMAP1610_GPIO_IRQENABLE1 0x001c
+#define OMAP1610_GPIO_WAKEUPENABLE 0x0028
#define OMAP1610_GPIO_DATAIN 0x002c
#define OMAP1610_GPIO_DATAOUT 0x0030
#define OMAP1610_GPIO_DIRECTION 0x0034
#define OMAP1610_GPIO_EDGE_CTRL1 0x0038
#define OMAP1610_GPIO_EDGE_CTRL2 0x003c
#define OMAP1610_GPIO_CLEAR_IRQENABLE1 0x009c
+#define OMAP1610_GPIO_CLEAR_WAKEUPENA 0x00a8
#define OMAP1610_GPIO_CLEAR_DATAOUT 0x00b0
#define OMAP1610_GPIO_SET_IRQENABLE1 0x00dc
+#define OMAP1610_GPIO_SET_WAKEUPENA 0x00e8
#define OMAP1610_GPIO_SET_DATAOUT 0x00f0
/*
* OMAP730 specific GPIO registers
*/
-#define OMAP730_GPIO1_BASE 0xfffbc000
-#define OMAP730_GPIO2_BASE 0xfffbc800
-#define OMAP730_GPIO3_BASE 0xfffbd000
-#define OMAP730_GPIO4_BASE 0xfffbd800
-#define OMAP730_GPIO5_BASE 0xfffbe000
-#define OMAP730_GPIO6_BASE 0xfffbe800
+#define OMAP730_GPIO1_BASE (void __iomem *)0xfffbc000
+#define OMAP730_GPIO2_BASE (void __iomem *)0xfffbc800
+#define OMAP730_GPIO3_BASE (void __iomem *)0xfffbd000
+#define OMAP730_GPIO4_BASE (void __iomem *)0xfffbd800
+#define OMAP730_GPIO5_BASE (void __iomem *)0xfffbe000
+#define OMAP730_GPIO6_BASE (void __iomem *)0xfffbe800
#define OMAP730_GPIO_DATA_INPUT 0x00
#define OMAP730_GPIO_DATA_OUTPUT 0x04
#define OMAP730_GPIO_DIR_CONTROL 0x08
#define OMAP730_GPIO_INT_MASK 0x10
#define OMAP730_GPIO_INT_STATUS 0x14
+/*
+ * omap24xx specific GPIO registers
+ */
+#define OMAP24XX_GPIO1_BASE (void __iomem *)0x48018000
+#define OMAP24XX_GPIO2_BASE (void __iomem *)0x4801a000
+#define OMAP24XX_GPIO3_BASE (void __iomem *)0x4801c000
+#define OMAP24XX_GPIO4_BASE (void __iomem *)0x4801e000
+#define OMAP24XX_GPIO_REVISION 0x0000
+#define OMAP24XX_GPIO_SYSCONFIG 0x0010
+#define OMAP24XX_GPIO_SYSSTATUS 0x0014
+#define OMAP24XX_GPIO_IRQSTATUS1 0x0018
+#define OMAP24XX_GPIO_IRQENABLE1 0x001c
+#define OMAP24XX_GPIO_CTRL 0x0030
+#define OMAP24XX_GPIO_OE 0x0034
+#define OMAP24XX_GPIO_DATAIN 0x0038
+#define OMAP24XX_GPIO_DATAOUT 0x003c
+#define OMAP24XX_GPIO_LEVELDETECT0 0x0040
+#define OMAP24XX_GPIO_LEVELDETECT1 0x0044
+#define OMAP24XX_GPIO_RISINGDETECT 0x0048
+#define OMAP24XX_GPIO_FALLINGDETECT 0x004c
+#define OMAP24XX_GPIO_CLEARIRQENABLE1 0x0060
+#define OMAP24XX_GPIO_SETIRQENABLE1 0x0064
+#define OMAP24XX_GPIO_CLEARWKUENA 0x0080
+#define OMAP24XX_GPIO_SETWKUENA 0x0084
+#define OMAP24XX_GPIO_CLEARDATAOUT 0x0090
+#define OMAP24XX_GPIO_SETDATAOUT 0x0094
+
#define OMAP_MPUIO_MASK (~OMAP_MAX_GPIO_LINES & 0xff)
struct gpio_bank {
- u32 base;
+ void __iomem *base;
u16 irq;
u16 virtual_irq_start;
- u8 method;
+ int method;
u32 reserved_map;
+ u32 suspend_wakeup;
+ u32 saved_wakeup;
spinlock_t lock;
};
#define METHOD_GPIO_1510 1
#define METHOD_GPIO_1610 2
#define METHOD_GPIO_730 3
+#define METHOD_GPIO_24XX 4
-#if defined(CONFIG_ARCH_OMAP16XX)
+#ifdef CONFIG_ARCH_OMAP16XX
static struct gpio_bank gpio_bank_1610[5] = {
{ OMAP_MPUIO_BASE, INT_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO},
{ OMAP1610_GPIO1_BASE, INT_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_1610 },
};
#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+static struct gpio_bank gpio_bank_24xx[4] = {
+ { OMAP24XX_GPIO1_BASE, INT_24XX_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_24XX },
+ { OMAP24XX_GPIO2_BASE, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_24XX },
+ { OMAP24XX_GPIO3_BASE, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_24XX },
+ { OMAP24XX_GPIO4_BASE, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96, METHOD_GPIO_24XX },
+};
+#endif
+
static struct gpio_bank *gpio_bank;
static int gpio_bank_count;
return &gpio_bank[1 + (gpio >> 5)];
}
#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (cpu_is_omap24xx())
+ return &gpio_bank[gpio >> 5];
+#endif
}
static inline int get_gpio_index(int gpio)
{
+#ifdef CONFIG_ARCH_OMAP730
if (cpu_is_omap730())
return gpio & 0x1f;
- else
- return gpio & 0x0f;
+#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (cpu_is_omap24xx())
+ return gpio & 0x1f;
+#endif
+ return gpio & 0x0f;
}
static inline int gpio_valid(int gpio)
if (cpu_is_omap730() && gpio < 192)
return 0;
#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (cpu_is_omap24xx() && gpio < 128)
+ return 0;
+#endif
return -1;
}
static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input)
{
- u32 reg = bank->base;
+ void __iomem *reg = bank->base;
u32 l;
switch (bank->method) {
case METHOD_GPIO_730:
reg += OMAP730_GPIO_DIR_CONTROL;
break;
+ case METHOD_GPIO_24XX:
+ reg += OMAP24XX_GPIO_OE;
+ break;
}
l = __raw_readl(reg);
if (is_input)
static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable)
{
- u32 reg = bank->base;
+ void __iomem *reg = bank->base;
u32 l = 0;
switch (bank->method) {
else
l &= ~(1 << gpio);
break;
+ case METHOD_GPIO_24XX:
+ if (enable)
+ reg += OMAP24XX_GPIO_SETDATAOUT;
+ else
+ reg += OMAP24XX_GPIO_CLEARDATAOUT;
+ l = 1 << gpio;
+ break;
default:
BUG();
return;
int omap_get_gpio_datain(int gpio)
{
struct gpio_bank *bank;
- u32 reg;
+ void __iomem *reg;
if (check_gpio(gpio) < 0)
return -1;
case METHOD_GPIO_730:
reg += OMAP730_GPIO_DATA_INPUT;
break;
+ case METHOD_GPIO_24XX:
+ reg += OMAP24XX_GPIO_DATAIN;
+ break;
default:
BUG();
return -1;
}
- return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
+ return (__raw_readl(reg)
+ & (1 << get_gpio_index(gpio))) != 0;
}
-static void _set_gpio_edge_ctrl(struct gpio_bank *bank, int gpio, int edge)
+#define MOD_REG_BIT(reg, bit_mask, set) \
+do { \
+ int l = __raw_readl(base + reg); \
+ if (set) l |= bit_mask; \
+ else l &= ~bit_mask; \
+ __raw_writel(l, base + reg); \
+} while(0)
+
+static inline void set_24xx_gpio_triggering(void __iomem *base, int gpio, int trigger)
{
- u32 reg = bank->base;
- u32 l;
+ u32 gpio_bit = 1 << gpio;
+
+ MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT0, gpio_bit,
+ trigger & IRQT_LOW);
+ MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT1, gpio_bit,
+ trigger & IRQT_HIGH);
+ MOD_REG_BIT(OMAP24XX_GPIO_RISINGDETECT, gpio_bit,
+ trigger & IRQT_RISING);
+ MOD_REG_BIT(OMAP24XX_GPIO_FALLINGDETECT, gpio_bit,
+ trigger & IRQT_FALLING);
+ /* FIXME: Possibly do 'set_irq_handler(j, do_level_IRQ)' if only level
+ * triggering requested. */
+}
+
+static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger)
+{
+ void __iomem *reg = bank->base;
+ u32 l = 0;
switch (bank->method) {
case METHOD_MPUIO:
reg += OMAP_MPUIO_GPIO_INT_EDGE;
l = __raw_readl(reg);
- if (edge == OMAP_GPIO_RISING_EDGE)
+ if (trigger == IRQT_RISING)
l |= 1 << gpio;
- else
+ else if (trigger == IRQT_FALLING)
l &= ~(1 << gpio);
- __raw_writel(l, reg);
+ else
+ goto bad;
break;
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_INT_CONTROL;
l = __raw_readl(reg);
- if (edge == OMAP_GPIO_RISING_EDGE)
+ if (trigger == IRQT_RISING)
l |= 1 << gpio;
- else
+ else if (trigger == IRQT_FALLING)
l &= ~(1 << gpio);
- __raw_writel(l, reg);
+ else
+ goto bad;
break;
case METHOD_GPIO_1610:
- edge &= 0x03;
if (gpio & 0x08)
reg += OMAP1610_GPIO_EDGE_CTRL2;
else
reg += OMAP1610_GPIO_EDGE_CTRL1;
gpio &= 0x07;
+ /* We allow only edge triggering, i.e. two lowest bits */
+ if (trigger & ~IRQT_BOTHEDGE)
+ BUG();
+ /* NOTE: knows __IRQT_{FAL,RIS}EDGE match OMAP hardware */
+ trigger &= 0x03;
l = __raw_readl(reg);
l &= ~(3 << (gpio << 1));
- l |= edge << (gpio << 1);
- __raw_writel(l, reg);
+ l |= trigger << (gpio << 1);
break;
case METHOD_GPIO_730:
reg += OMAP730_GPIO_INT_CONTROL;
l = __raw_readl(reg);
- if (edge == OMAP_GPIO_RISING_EDGE)
+ if (trigger == IRQT_RISING)
l |= 1 << gpio;
- else
+ else if (trigger == IRQT_FALLING)
l &= ~(1 << gpio);
- __raw_writel(l, reg);
+ else
+ goto bad;
+ break;
+ case METHOD_GPIO_24XX:
+ set_24xx_gpio_triggering(reg, gpio, trigger);
break;
default:
BUG();
- return;
+ goto bad;
}
+ __raw_writel(l, reg);
+ return 0;
+bad:
+ return -EINVAL;
}
-void omap_set_gpio_edge_ctrl(int gpio, int edge)
+static int gpio_irq_type(unsigned irq, unsigned type)
{
struct gpio_bank *bank;
+ unsigned gpio;
+ int retval;
+
+ if (irq > IH_MPUIO_BASE)
+ gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
+ else
+ gpio = irq - IH_GPIO_BASE;
if (check_gpio(gpio) < 0)
- return;
+ return -EINVAL;
+
+ if (type & (__IRQT_LOWLVL|__IRQT_HIGHLVL|IRQT_PROBE))
+ return -EINVAL;
+
bank = get_gpio_bank(gpio);
spin_lock(&bank->lock);
- _set_gpio_edge_ctrl(bank, get_gpio_index(gpio), edge);
+ retval = _set_gpio_triggering(bank, get_gpio_index(gpio), type);
spin_unlock(&bank->lock);
-}
-
-
-static int _get_gpio_edge_ctrl(struct gpio_bank *bank, int gpio)
-{
- u32 reg = bank->base, l;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- l = __raw_readl(reg + OMAP_MPUIO_GPIO_INT_EDGE);
- return (l & (1 << gpio)) ?
- OMAP_GPIO_RISING_EDGE : OMAP_GPIO_FALLING_EDGE;
- case METHOD_GPIO_1510:
- l = __raw_readl(reg + OMAP1510_GPIO_INT_CONTROL);
- return (l & (1 << gpio)) ?
- OMAP_GPIO_RISING_EDGE : OMAP_GPIO_FALLING_EDGE;
- case METHOD_GPIO_1610:
- if (gpio & 0x08)
- reg += OMAP1610_GPIO_EDGE_CTRL2;
- else
- reg += OMAP1610_GPIO_EDGE_CTRL1;
- return (__raw_readl(reg) >> ((gpio & 0x07) << 1)) & 0x03;
- case METHOD_GPIO_730:
- l = __raw_readl(reg + OMAP730_GPIO_INT_CONTROL);
- return (l & (1 << gpio)) ?
- OMAP_GPIO_RISING_EDGE : OMAP_GPIO_FALLING_EDGE;
- default:
- BUG();
- return -1;
- }
+ return retval;
}
static void _clear_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
{
- u32 reg = bank->base;
+ void __iomem *reg = bank->base;
switch (bank->method) {
case METHOD_MPUIO:
case METHOD_GPIO_730:
reg += OMAP730_GPIO_INT_STATUS;
break;
+ case METHOD_GPIO_24XX:
+ reg += OMAP24XX_GPIO_IRQSTATUS1;
+ break;
default:
BUG();
return;
static void _enable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask, int enable)
{
- u32 reg = bank->base;
+ void __iomem *reg = bank->base;
u32 l;
switch (bank->method) {
else
l |= gpio_mask;
break;
+ case METHOD_GPIO_24XX:
+ if (enable)
+ reg += OMAP24XX_GPIO_SETIRQENABLE1;
+ else
+ reg += OMAP24XX_GPIO_CLEARIRQENABLE1;
+ l = gpio_mask;
+ break;
default:
BUG();
return;
_enable_gpio_irqbank(bank, 1 << get_gpio_index(gpio), enable);
}
+/*
+ * Note that ENAWAKEUP needs to be enabled in GPIO_SYSCONFIG register.
+ * 1510 does not seem to have a wake-up register. If JTAG is connected
+ * to the target, system will wake up always on GPIO events. While
+ * system is running all registered GPIO interrupts need to have wake-up
+ * enabled. When system is suspended, only selected GPIO interrupts need
+ * to have wake-up enabled.
+ */
+static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable)
+{
+ switch (bank->method) {
+ case METHOD_GPIO_1610:
+ case METHOD_GPIO_24XX:
+ spin_lock(&bank->lock);
+ if (enable)
+ bank->suspend_wakeup |= (1 << gpio);
+ else
+ bank->suspend_wakeup &= ~(1 << gpio);
+ spin_unlock(&bank->lock);
+ return 0;
+ default:
+ printk(KERN_ERR "Can't enable GPIO wakeup for method %i\n",
+ bank->method);
+ return -EINVAL;
+ }
+}
+
+/* Use disable_irq_wake() and enable_irq_wake() functions from drivers */
+static int gpio_wake_enable(unsigned int irq, unsigned int enable)
+{
+ unsigned int gpio = irq - IH_GPIO_BASE;
+ struct gpio_bank *bank;
+ int retval;
+
+ if (check_gpio(gpio) < 0)
+ return -ENODEV;
+ bank = get_gpio_bank(gpio);
+ spin_lock(&bank->lock);
+ retval = _set_gpio_wakeup(bank, get_gpio_index(gpio), enable);
+ spin_unlock(&bank->lock);
+
+ return retval;
+}
+
int omap_request_gpio(int gpio)
{
struct gpio_bank *bank;
return -1;
}
bank->reserved_map |= (1 << get_gpio_index(gpio));
+
+ /* Set trigger to none. You need to enable the trigger after request_irq */
+ _set_gpio_triggering(bank, get_gpio_index(gpio), IRQT_NOEDGE);
+
#ifdef CONFIG_ARCH_OMAP1510
if (bank->method == METHOD_GPIO_1510) {
- u32 reg;
+ void __iomem *reg;
- /* Claim the pin for the ARM */
+ /* Claim the pin for MPU */
reg = bank->base + OMAP1510_GPIO_PIN_CONTROL;
__raw_writel(__raw_readl(reg) | (1 << get_gpio_index(gpio)), reg);
}
#endif
+#ifdef CONFIG_ARCH_OMAP16XX
+ if (bank->method == METHOD_GPIO_1610) {
+ /* Enable wake-up during idle for dynamic tick */
+ void __iomem *reg = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
+ __raw_writel(1 << get_gpio_index(gpio), reg);
+ }
+#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (bank->method == METHOD_GPIO_24XX) {
+ /* Enable wake-up during idle for dynamic tick */
+ void __iomem *reg = bank->base + OMAP24XX_GPIO_SETWKUENA;
+ __raw_writel(1 << get_gpio_index(gpio), reg);
+ }
+#endif
spin_unlock(&bank->lock);
return 0;
spin_unlock(&bank->lock);
return;
}
+#ifdef CONFIG_ARCH_OMAP16XX
+ if (bank->method == METHOD_GPIO_1610) {
+ /* Disable wake-up during idle for dynamic tick */
+ void __iomem *reg = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
+ __raw_writel(1 << get_gpio_index(gpio), reg);
+ }
+#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (bank->method == METHOD_GPIO_24XX) {
+ /* Disable wake-up during idle for dynamic tick */
+ void __iomem *reg = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
+ __raw_writel(1 << get_gpio_index(gpio), reg);
+ }
+#endif
bank->reserved_map &= ~(1 << get_gpio_index(gpio));
_set_gpio_direction(bank, get_gpio_index(gpio), 1);
_set_gpio_irqenable(bank, gpio, 0);
static void gpio_irq_handler(unsigned int irq, struct irqdesc *desc,
struct pt_regs *regs)
{
- u32 isr_reg = 0;
+ void __iomem *isr_reg = NULL;
u32 isr;
unsigned int gpio_irq;
struct gpio_bank *bank;
if (bank->method == METHOD_GPIO_730)
isr_reg = bank->base + OMAP730_GPIO_INT_STATUS;
#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (bank->method == METHOD_GPIO_24XX)
+ isr_reg = bank->base + OMAP24XX_GPIO_IRQSTATUS1;
+#endif
- isr = __raw_readl(isr_reg);
- _enable_gpio_irqbank(bank, isr, 0);
- _clear_gpio_irqbank(bank, isr);
- _enable_gpio_irqbank(bank, isr, 1);
- desc->chip->unmask(irq);
-
- if (unlikely(!isr))
- return;
-
- gpio_irq = bank->virtual_irq_start;
- for (; isr != 0; isr >>= 1, gpio_irq++) {
- struct irqdesc *d;
- if (!(isr & 1))
- continue;
- d = irq_desc + gpio_irq;
- desc_handle_irq(gpio_irq, d, regs);
- }
+ while(1) {
+ isr = __raw_readl(isr_reg);
+ _enable_gpio_irqbank(bank, isr, 0);
+ _clear_gpio_irqbank(bank, isr);
+ _enable_gpio_irqbank(bank, isr, 1);
+ desc->chip->unmask(irq);
+
+ if (!isr)
+ break;
+
+ gpio_irq = bank->virtual_irq_start;
+ for (; isr != 0; isr >>= 1, gpio_irq++) {
+ struct irqdesc *d;
+ if (!(isr & 1))
+ continue;
+ d = irq_desc + gpio_irq;
+ desc_handle_irq(gpio_irq, d, regs);
+ }
+ }
}
static void gpio_ack_irq(unsigned int irq)
static void gpio_unmask_irq(unsigned int irq)
{
unsigned int gpio = irq - IH_GPIO_BASE;
+ unsigned int gpio_idx = get_gpio_index(gpio);
struct gpio_bank *bank = get_gpio_bank(gpio);
- if (_get_gpio_edge_ctrl(bank, get_gpio_index(gpio)) == OMAP_GPIO_NO_EDGE) {
- printk(KERN_ERR "OMAP GPIO %d: trying to enable GPIO IRQ while no edge is set\n",
- gpio);
- _set_gpio_edge_ctrl(bank, get_gpio_index(gpio), OMAP_GPIO_RISING_EDGE);
- }
- _set_gpio_irqenable(bank, gpio, 1);
+ _set_gpio_irqenable(bank, gpio_idx, 1);
}
static void mpuio_ack_irq(unsigned int irq)
}
static struct irqchip gpio_irq_chip = {
- .ack = gpio_ack_irq,
- .mask = gpio_mask_irq,
- .unmask = gpio_unmask_irq,
+ .ack = gpio_ack_irq,
+ .mask = gpio_mask_irq,
+ .unmask = gpio_unmask_irq,
+ .set_type = gpio_irq_type,
+ .set_wake = gpio_wake_enable,
};
static struct irqchip mpuio_irq_chip = {
};
static int initialized = 0;
+static struct clk * gpio_ck = NULL;
static int __init _omap_gpio_init(void)
{
initialized = 1;
+ if (cpu_is_omap1510()) {
+ gpio_ck = clk_get(NULL, "arm_gpio_ck");
+ if (IS_ERR(gpio_ck))
+ printk("Could not get arm_gpio_ck\n");
+ else
+ clk_use(gpio_ck);
+ }
+
#ifdef CONFIG_ARCH_OMAP1510
if (cpu_is_omap1510()) {
printk(KERN_INFO "OMAP1510 GPIO hardware\n");
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (cpu_is_omap16xx()) {
- int rev;
+ u32 rev;
gpio_bank_count = 5;
gpio_bank = gpio_bank_1610;
gpio_bank = gpio_bank_730;
}
#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (cpu_is_omap24xx()) {
+ int rev;
+
+ gpio_bank_count = 4;
+ gpio_bank = gpio_bank_24xx;
+ rev = omap_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION);
+ printk(KERN_INFO "OMAP24xx GPIO hardware version %d.%d\n",
+ (rev >> 4) & 0x0f, rev & 0x0f);
+ }
+#endif
for (i = 0; i < gpio_bank_count; i++) {
int j, gpio_count = 16;
if (bank->method == METHOD_GPIO_1610) {
__raw_writew(0x0000, bank->base + OMAP1610_GPIO_IRQENABLE1);
__raw_writew(0xffff, bank->base + OMAP1610_GPIO_IRQSTATUS1);
+ __raw_writew(0x0014, bank->base + OMAP1610_GPIO_SYSCONFIG);
}
#endif
#ifdef CONFIG_ARCH_OMAP730
gpio_count = 32; /* 730 has 32-bit GPIOs */
}
#endif
+#ifdef CONFIG_ARCH_OMAP24XX
+ if (bank->method == METHOD_GPIO_24XX) {
+ __raw_writel(0x00000000, bank->base + OMAP24XX_GPIO_IRQENABLE1);
+ __raw_writel(0xffffffff, bank->base + OMAP24XX_GPIO_IRQSTATUS1);
+
+ gpio_count = 32;
+ }
+#endif
for (j = bank->virtual_irq_start;
j < bank->virtual_irq_start + gpio_count; j++) {
if (bank->method == METHOD_MPUIO)
/* Enable system clock for GPIO module.
* The CAM_CLK_CTRL *is* really the right place. */
- if (cpu_is_omap1610() || cpu_is_omap1710())
+ if (cpu_is_omap16xx())
omap_writel(omap_readl(ULPD_CAM_CLK_CTRL) | 0x04, ULPD_CAM_CLK_CTRL);
return 0;
}
+#if defined (CONFIG_ARCH_OMAP16XX) || defined (CONFIG_ARCH_OMAP24XX)
+static int omap_gpio_suspend(struct sys_device *dev, pm_message_t mesg)
+{
+ int i;
+
+ if (!cpu_is_omap24xx() && !cpu_is_omap16xx())
+ return 0;
+
+ for (i = 0; i < gpio_bank_count; i++) {
+ struct gpio_bank *bank = &gpio_bank[i];
+ void __iomem *wake_status;
+ void __iomem *wake_clear;
+ void __iomem *wake_set;
+
+ switch (bank->method) {
+ case METHOD_GPIO_1610:
+ wake_status = bank->base + OMAP1610_GPIO_WAKEUPENABLE;
+ wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
+ wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
+ break;
+ case METHOD_GPIO_24XX:
+ wake_status = bank->base + OMAP24XX_GPIO_SETWKUENA;
+ wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
+ wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA;
+ break;
+ default:
+ continue;
+ }
+
+ spin_lock(&bank->lock);
+ bank->saved_wakeup = __raw_readl(wake_status);
+ __raw_writel(0xffffffff, wake_clear);
+ __raw_writel(bank->suspend_wakeup, wake_set);
+ spin_unlock(&bank->lock);
+ }
+
+ return 0;
+}
+
+static int omap_gpio_resume(struct sys_device *dev)
+{
+ int i;
+
+ if (!cpu_is_omap24xx() && !cpu_is_omap16xx())
+ return 0;
+
+ for (i = 0; i < gpio_bank_count; i++) {
+ struct gpio_bank *bank = &gpio_bank[i];
+ void __iomem *wake_clear;
+ void __iomem *wake_set;
+
+ switch (bank->method) {
+ case METHOD_GPIO_1610:
+ wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
+ wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
+ break;
+ case METHOD_GPIO_24XX:
+ wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
+ wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
+ break;
+ default:
+ continue;
+ }
+
+ spin_lock(&bank->lock);
+ __raw_writel(0xffffffff, wake_clear);
+ __raw_writel(bank->saved_wakeup, wake_set);
+ spin_unlock(&bank->lock);
+ }
+
+ return 0;
+}
+
+static struct sysdev_class omap_gpio_sysclass = {
+ set_kset_name("gpio"),
+ .suspend = omap_gpio_suspend,
+ .resume = omap_gpio_resume,
+};
+
+static struct sys_device omap_gpio_device = {
+ .id = 0,
+ .cls = &omap_gpio_sysclass,
+};
+#endif
+
/*
* This may get called early from board specific init
*/
return 0;
}
+static int __init omap_gpio_sysinit(void)
+{
+ int ret = 0;
+
+ if (!initialized)
+ ret = _omap_gpio_init();
+
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP24XX)
+ if (cpu_is_omap16xx() || cpu_is_omap24xx()) {
+ if (ret == 0) {
+ ret = sysdev_class_register(&omap_gpio_sysclass);
+ if (ret == 0)
+ ret = sysdev_register(&omap_gpio_device);
+ }
+ }
+#endif
+
+ return ret;
+}
+
EXPORT_SYMBOL(omap_request_gpio);
EXPORT_SYMBOL(omap_free_gpio);
EXPORT_SYMBOL(omap_set_gpio_direction);
EXPORT_SYMBOL(omap_set_gpio_dataout);
EXPORT_SYMBOL(omap_get_gpio_datain);
-EXPORT_SYMBOL(omap_set_gpio_edge_ctrl);
-arch_initcall(omap_gpio_init);
+arch_initcall(omap_gpio_sysinit);
#include <asm/arch/dma.h>
#include <asm/arch/mux.h>
#include <asm/arch/irqs.h>
+#include <asm/arch/dsp_common.h>
#include <asm/arch/mcbsp.h>
#include <asm/hardware/clock.h>
return -1;
}
-#define EN_XORPCK 1
-#define DSP_RSTCT2 0xe1008014
-
static void omap_mcbsp_dsp_request(void)
{
if (cpu_is_omap1510() || cpu_is_omap16xx()) {
/* enable 12MHz clock to mcbsp 1 & 3 */
clk_use(mcbsp_dspxor_ck);
+
+ /*
+ * DSP external peripheral reset
+ * FIXME: This should be moved to dsp code
+ */
__raw_writew(__raw_readw(DSP_RSTCT2) | 1 | 1 << 1,
DSP_RSTCT2);
}
pull_orig = 0, pull = 0;
unsigned int mask, warn = 0;
+ if (cpu_is_omap7xx())
+ return 0;
+
if (reg_cfg > ARRAY_SIZE(reg_cfg_table)) {
printk(KERN_ERR "MUX: reg_cfg %d\n", reg_cfg);
return -EINVAL;
#include <linux/config.h>
#include <linux/module.h>
+#include <linux/version.h>
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <linux/pm.h>
+#include <linux/interrupt.h>
#include <asm/io.h>
+#include <asm/irq.h>
#include <asm/mach/time.h>
-#include <asm/mach-types.h>
+#include <asm/mach/irq.h>
-#include <asm/arch/omap16xx.h>
+#include <asm/mach-types.h>
+#include <asm/arch/irqs.h>
+#include <asm/arch/tc.h>
#include <asm/arch/pm.h>
#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
#include <asm/arch/tps65010.h>
+#include <asm/arch/dsp_common.h>
#include "clock.h"
+#include "sram.h"
static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
static unsigned short ulpd_sleep_save[ULPD_SLEEP_SAVE_SIZE];
static unsigned int mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_SIZE];
static unsigned int mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_SIZE];
+static void (*omap_sram_idle)(void) = NULL;
+static void (*omap_sram_suspend)(unsigned long r0, unsigned long r1) = NULL;
+
/*
* Let's power down on idle, but only if we are really
* idle, because once we start down the path of
*/
void omap_pm_idle(void)
{
- int (*func_ptr)(void) = 0;
unsigned int mask32 = 0;
/*
mask32 = omap_readl(ARM_SYSST);
/*
+ * Prevent the ULPD from entering low power state by setting
+ * POWER_CTRL_REG:4 = 0
+ */
+ omap_writew(omap_readw(ULPD_POWER_CTRL) &
+ ~ULPD_DEEP_SLEEP_TRANSITION_EN, ULPD_POWER_CTRL);
+
+ /*
* Since an interrupt may set up a timer, we don't want to
* reprogram the hardware timer with interrupts enabled.
* Re-enable interrupts only after returning from idle.
if ((mask32 & DSP_IDLE) == 0) {
__asm__ volatile ("mcr p15, 0, r0, c7, c0, 4");
- } else {
-
- if (cpu_is_omap1510()) {
- func_ptr = (void *)(OMAP1510_SRAM_IDLE_SUSPEND);
- } else if (cpu_is_omap1610() || cpu_is_omap1710()) {
- func_ptr = (void *)(OMAP1610_SRAM_IDLE_SUSPEND);
- } else if (cpu_is_omap5912()) {
- func_ptr = (void *)(OMAP5912_SRAM_IDLE_SUSPEND);
- }
+ } else
+ omap_sram_idle();
- func_ptr();
- }
local_fiq_enable();
local_irq_enable();
}
*/
static void omap_pm_wakeup_setup(void)
{
- /*
- * Enable ARM XOR clock and release peripheral from reset by
- * writing 1 to PER_EN bit in ARM_RSTCT2, this is required
- * for UART configuration to use UART2 to wake up.
- */
-
- omap_writel(omap_readl(ARM_IDLECT2) | ENABLE_XORCLK, ARM_IDLECT2);
- omap_writel(omap_readl(ARM_RSTCT2) | PER_EN, ARM_RSTCT2);
- omap_writew(MODEM_32K_EN, ULPD_CLOCK_CTRL);
+ u32 level1_wake = OMAP_IRQ_BIT(INT_IH2_IRQ);
+ u32 level2_wake = OMAP_IRQ_BIT(INT_UART2) | OMAP_IRQ_BIT(INT_KEYBOARD);
/*
- * Turn off all interrupts except L1-2nd level cascade,
- * and the L2 wakeup interrupts: keypad and UART2.
+ * Turn off all interrupts except GPIO bank 1, L1-2nd level cascade,
+ * and the L2 wakeup interrupts: keypad and UART2. Note that the
+ * drivers must still separately call omap_set_gpio_wakeup() to
+ * wake up to a GPIO interrupt.
*/
+ if (cpu_is_omap1510() || cpu_is_omap16xx())
+ level1_wake |= OMAP_IRQ_BIT(INT_GPIO_BANK1);
+ else if (cpu_is_omap730())
+ level1_wake |= OMAP_IRQ_BIT(INT_730_GPIO_BANK1);
- omap_writel(~IRQ_LEVEL2, OMAP_IH1_MIR);
+ omap_writel(~level1_wake, OMAP_IH1_MIR);
- if (cpu_is_omap1510()) {
- omap_writel(~(IRQ_UART2 | IRQ_KEYBOARD), OMAP_IH2_MIR);
- }
+ if (cpu_is_omap1510())
+ omap_writel(~level2_wake, OMAP_IH2_MIR);
+ /* INT_1610_WAKE_UP_REQ is needed for GPIO wakeup... */
if (cpu_is_omap16xx()) {
- omap_writel(~(IRQ_UART2 | IRQ_KEYBOARD), OMAP_IH2_0_MIR);
-
- omap_writel(~0x0, OMAP_IH2_1_MIR);
+ omap_writel(~level2_wake, OMAP_IH2_0_MIR);
+ omap_writel(~OMAP_IRQ_BIT(INT_1610_WAKE_UP_REQ), OMAP_IH2_1_MIR);
omap_writel(~0x0, OMAP_IH2_2_MIR);
omap_writel(~0x0, OMAP_IH2_3_MIR);
}
- /* New IRQ agreement */
+ /* New IRQ agreement, recalculate in cascade order */
+ omap_writel(1, OMAP_IH2_CONTROL);
omap_writel(1, OMAP_IH1_CONTROL);
-
- /* external PULL to down, bit 22 = 0 */
- omap_writel(omap_readl(PULL_DWN_CTRL_2) & ~(1<<22), PULL_DWN_CTRL_2);
}
void omap_pm_suspend(void)
{
- unsigned int mask32 = 0;
unsigned long arg0 = 0, arg1 = 0;
- int (*func_ptr)(unsigned short, unsigned short) = 0;
- unsigned short save_dsp_idlect2;
- printk("PM: OMAP%x is entering deep sleep now ...\n", system_rev);
+ printk("PM: OMAP%x is trying to enter deep sleep...\n", system_rev);
+
+ omap_serial_wake_trigger(1);
if (machine_is_omap_osk()) {
/* Stop LED1 (D9) blink */
tps65010_set_led(LED1, OFF);
}
+ omap_writew(0xffff, ULPD_SOFT_DISABLE_REQ_REG);
+
/*
- * Step 1: turn off interrupts
+ * Step 1: turn off interrupts (FIXME: NOTE: already disabled)
*/
local_irq_disable();
ARM_SAVE(ARM_CKCTL);
ARM_SAVE(ARM_IDLECT1);
ARM_SAVE(ARM_IDLECT2);
+ if (!(cpu_is_omap1510()))
+ ARM_SAVE(ARM_IDLECT3);
ARM_SAVE(ARM_EWUPCT);
ARM_SAVE(ARM_RSTCT1);
ARM_SAVE(ARM_RSTCT2);
ULPD_SAVE(ULPD_CLOCK_CTRL);
ULPD_SAVE(ULPD_STATUS_REQ);
- /*
- * Step 3: LOW_PWR signal enabling
- *
- * Allow the LOW_PWR signal to be visible on MPUIO5 ball.
- */
- if (cpu_is_omap1510()) {
- /* POWER_CTRL_REG = 0x1 (LOW_POWER is available) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) |
- OMAP1510_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- } else if (cpu_is_omap16xx()) {
- /* POWER_CTRL_REG = 0x1 (LOW_POWER is available) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) |
- OMAP1610_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- }
-
- /* configure LOW_PWR pin */
- omap_cfg_reg(T20_1610_LOW_PWR);
+ /* (Step 3 removed - we now allow deep sleep by default) */
/*
* Step 4: OMAP DSP Shutdown
*/
- /* Set DSP_RST = 1 and DSP_EN = 0, put DSP block into reset */
- omap_writel((omap_readl(ARM_RSTCT1) | DSP_RST) & ~DSP_ENABLE,
- ARM_RSTCT1);
-
- /* Set DSP boot mode to DSP-IDLE, DSP_BOOT_MODE = 0x2 */
- omap_writel(DSP_IDLE_MODE, MPUI_DSP_BOOT_CONFIG);
-
- /* Set EN_DSPCK = 0, stop DSP block clock */
- omap_writel(omap_readl(ARM_CKCTL) & ~DSP_CLOCK_ENABLE, ARM_CKCTL);
-
- /* Stop any DSP domain clocks */
- omap_writel(omap_readl(ARM_IDLECT2) | (1<<EN_APICK), ARM_IDLECT2);
- save_dsp_idlect2 = __raw_readw(DSP_IDLECT2);
- __raw_writew(0, DSP_IDLECT2);
/*
* Step 5: Wakeup Event Setup
omap_pm_wakeup_setup();
/*
- * Step 6a: ARM and Traffic controller shutdown
- *
- * Step 6 starts here with clock and watchdog disable
+ * Step 6: ARM and Traffic controller shutdown
*/
- /* stop clocks */
- mask32 = omap_readl(ARM_IDLECT2);
- mask32 &= ~(1<<EN_WDTCK); /* bit 0 -> 0 (WDT clock) */
- mask32 |= (1<<EN_XORPCK); /* bit 1 -> 1 (XORPCK clock) */
- mask32 &= ~(1<<EN_PERCK); /* bit 2 -> 0 (MPUPER_CK clock) */
- mask32 &= ~(1<<EN_LCDCK); /* bit 3 -> 0 (LCDC clock) */
- mask32 &= ~(1<<EN_LBCK); /* bit 4 -> 0 (local bus clock) */
- mask32 |= (1<<EN_APICK); /* bit 6 -> 1 (MPUI clock) */
- mask32 &= ~(1<<EN_TIMCK); /* bit 7 -> 0 (MPU timer clock) */
- mask32 &= ~(1<<DMACK_REQ); /* bit 8 -> 0 (DMAC clock) */
- mask32 &= ~(1<<EN_GPIOCK); /* bit 9 -> 0 (GPIO clock) */
- omap_writel(mask32, ARM_IDLECT2);
-
/* disable ARM watchdog */
omap_writel(0x00F5, OMAP_WDT_TIMER_MODE);
omap_writel(0x00A0, OMAP_WDT_TIMER_MODE);
arg0 = arm_sleep_save[ARM_SLEEP_SAVE_ARM_IDLECT1];
arg1 = arm_sleep_save[ARM_SLEEP_SAVE_ARM_IDLECT2];
- if (cpu_is_omap1510()) {
- func_ptr = (void *)(OMAP1510_SRAM_API_SUSPEND);
- } else if (cpu_is_omap1610() || cpu_is_omap1710()) {
- func_ptr = (void *)(OMAP1610_SRAM_API_SUSPEND);
- } else if (cpu_is_omap5912()) {
- func_ptr = (void *)(OMAP5912_SRAM_API_SUSPEND);
- }
-
/*
* Step 6c: ARM and Traffic controller shutdown
*
* Jump to assembly code. The processor will stay there
* until wake up.
*/
-
- func_ptr(arg0, arg1);
+ omap_sram_suspend(arg0, arg1);
/*
* If we are here, processor is woken up!
*/
- if (cpu_is_omap1510()) {
- /* POWER_CTRL_REG = 0x0 (LOW_POWER is disabled) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) &
- ~OMAP1510_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- } else if (cpu_is_omap16xx()) {
- /* POWER_CTRL_REG = 0x0 (LOW_POWER is disabled) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) &
- ~OMAP1610_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- }
-
-
- /* Restore DSP clocks */
- omap_writel(omap_readl(ARM_IDLECT2) | (1<<EN_APICK), ARM_IDLECT2);
- __raw_writew(save_dsp_idlect2, DSP_IDLECT2);
- ARM_RESTORE(ARM_IDLECT2);
-
/*
* Restore ARM state, except ARM_IDLECT1/2 which omap_cpu_suspend did
*/
+ if (!(cpu_is_omap1510()))
+ ARM_RESTORE(ARM_IDLECT3);
ARM_RESTORE(ARM_CKCTL);
ARM_RESTORE(ARM_EWUPCT);
ARM_RESTORE(ARM_RSTCT1);
MPUI1610_RESTORE(OMAP_IH2_3_MIR);
}
+ omap_writew(0, ULPD_SOFT_DISABLE_REQ_REG);
+
/*
* Reenable interrupts
*/
local_irq_enable();
local_fiq_enable();
+ omap_serial_wake_trigger(0);
+
printk("PM: OMAP%x is re-starting from deep sleep...\n", system_rev);
if (machine_is_omap_osk()) {
ARM_SAVE(ARM_CKCTL);
ARM_SAVE(ARM_IDLECT1);
ARM_SAVE(ARM_IDLECT2);
+ if (!(cpu_is_omap1510()))
+ ARM_SAVE(ARM_IDLECT3);
ARM_SAVE(ARM_EWUPCT);
ARM_SAVE(ARM_RSTCT1);
ARM_SAVE(ARM_RSTCT2);
"ARM_CKCTL_REG: 0x%-8x \n"
"ARM_IDLECT1_REG: 0x%-8x \n"
"ARM_IDLECT2_REG: 0x%-8x \n"
+ "ARM_IDLECT3_REG: 0x%-8x \n"
"ARM_EWUPCT_REG: 0x%-8x \n"
"ARM_RSTCT1_REG: 0x%-8x \n"
"ARM_RSTCT2_REG: 0x%-8x \n"
ARM_SHOW(ARM_CKCTL),
ARM_SHOW(ARM_IDLECT1),
ARM_SHOW(ARM_IDLECT2),
+ ARM_SHOW(ARM_IDLECT3),
ARM_SHOW(ARM_EWUPCT),
ARM_SHOW(ARM_RSTCT1),
ARM_SHOW(ARM_RSTCT2),
entry = create_proc_read_entry("driver/omap_pm",
S_IWUSR | S_IRUGO, NULL,
- omap_pm_read_proc, 0);
+ omap_pm_read_proc, NULL);
}
#endif /* DEBUG && CONFIG_PROC_FS */
}
-struct pm_ops omap_pm_ops ={
+static irqreturn_t omap_wakeup_interrupt(int irq, void * dev,
+ struct pt_regs * regs)
+{
+ return IRQ_HANDLED;
+}
+
+static struct irqaction omap_wakeup_irq = {
+ .name = "peripheral wakeup",
+ .flags = SA_INTERRUPT,
+ .handler = omap_wakeup_interrupt
+};
+
+
+
+static struct pm_ops omap_pm_ops ={
.pm_disk_mode = 0,
.prepare = omap_pm_prepare,
.enter = omap_pm_enter,
static int __init omap_pm_init(void)
{
printk("Power Management for TI OMAP.\n");
- pm_idle = omap_pm_idle;
/*
* We copy the assembler sleep/wakeup routines to SRAM.
* These routines need to be in SRAM as that's the only
* memory the MPU can see when it wakes up.
*/
-
-#ifdef CONFIG_ARCH_OMAP1510
if (cpu_is_omap1510()) {
- memcpy((void *)OMAP1510_SRAM_IDLE_SUSPEND,
- omap1510_idle_loop_suspend,
- omap1510_idle_loop_suspend_sz);
- memcpy((void *)OMAP1510_SRAM_API_SUSPEND, omap1510_cpu_suspend,
- omap1510_cpu_suspend_sz);
- } else
-#endif
- if (cpu_is_omap1610() || cpu_is_omap1710()) {
- memcpy((void *)OMAP1610_SRAM_IDLE_SUSPEND,
- omap1610_idle_loop_suspend,
- omap1610_idle_loop_suspend_sz);
- memcpy((void *)OMAP1610_SRAM_API_SUSPEND, omap1610_cpu_suspend,
- omap1610_cpu_suspend_sz);
- } else if (cpu_is_omap5912()) {
- memcpy((void *)OMAP5912_SRAM_IDLE_SUSPEND,
- omap1610_idle_loop_suspend,
- omap1610_idle_loop_suspend_sz);
- memcpy((void *)OMAP5912_SRAM_API_SUSPEND, omap1610_cpu_suspend,
- omap1610_cpu_suspend_sz);
+ omap_sram_idle = omap_sram_push(omap1510_idle_loop_suspend,
+ omap1510_idle_loop_suspend_sz);
+ omap_sram_suspend = omap_sram_push(omap1510_cpu_suspend,
+ omap1510_cpu_suspend_sz);
+ } else if (cpu_is_omap16xx()) {
+ omap_sram_idle = omap_sram_push(omap1610_idle_loop_suspend,
+ omap1610_idle_loop_suspend_sz);
+ omap_sram_suspend = omap_sram_push(omap1610_cpu_suspend,
+ omap1610_cpu_suspend_sz);
}
+ if (omap_sram_idle == NULL || omap_sram_suspend == NULL) {
+ printk(KERN_ERR "PM not initialized: Missing SRAM support\n");
+ return -ENODEV;
+ }
+
+ pm_idle = omap_pm_idle;
+
+ setup_irq(INT_1610_WAKE_UP_REQ, &omap_wakeup_irq);
+#if 0
+ /* --- BEGIN BOARD-DEPENDENT CODE --- */
+ /* Sleepx mask direction */
+ omap_writew((omap_readw(0xfffb5008) & ~2), 0xfffb5008);
+ /* Unmask sleepx signal */
+ omap_writew((omap_readw(0xfffb5004) & ~2), 0xfffb5004);
+ /* --- END BOARD-DEPENDENT CODE --- */
+#endif
+
+ /* Program new power ramp-up time
+ * (0 for most boards since we don't lower voltage when in deep sleep)
+ */
+ omap_writew(ULPD_SETUP_ANALOG_CELL_3_VAL, ULPD_SETUP_ANALOG_CELL_3);
+
+ /* Setup ULPD POWER_CTRL_REG - enter deep sleep whenever possible */
+ omap_writew(ULPD_POWER_CTRL_REG_VAL, ULPD_POWER_CTRL);
+
+ /* Configure IDLECT3 */
+ if (cpu_is_omap16xx())
+ omap_writel(OMAP1610_IDLECT3_VAL, OMAP1610_IDLECT3);
+
pm_set_ops(&omap_pm_ops);
#if defined(DEBUG) && defined(CONFIG_PROC_FS)
omap_pm_init_proc();
#endif
+ /* configure LOW_PWR pin */
+ omap_cfg_reg(T20_1610_LOW_PWR);
+
return 0;
}
__initcall(omap_pm_init);
@ get ARM_IDLECT2 into r2
ldrh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
mov r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
+ orr r5, r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
+ orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
l_1510: subs r5, r5, #1
bne l_1510
/*
strh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
strh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
- ldmfd sp!, {r0 - r12, pc} @ restore regs and return
+ ldmfd sp!, {r0 - r12, pc} @ restore regs and return
ENTRY(omap1510_idle_loop_suspend_sz)
.word . - omap1510_idle_loop_suspend
@ turn off clock domains
@ get ARM_IDLECT2 into r2
ldrh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- mov r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff00
+ mov r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff
+ orr r5, r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
+ orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
l_1610: subs r5, r5, #1
bne l_1610
/*
strh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
strh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
- ldmfd sp!, {r0 - r12, pc} @ restore regs and return
+ ldmfd sp!, {r0 - r12, pc} @ restore regs and return
ENTRY(omap1610_idle_loop_suspend_sz)
.word . - omap1610_idle_loop_suspend
@ turn off clock domains
mov r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
+ orr r5, r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
+ orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
l_1510_2:
subs r5, r5, #1
bne l_1510_2
strh r0, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
@ restore regs and return
- ldmfd sp!, {r0 - r12, pc}
+ ldmfd sp!, {r0 - r12, pc}
ENTRY(omap1510_cpu_suspend_sz)
.word . - omap1510_cpu_suspend
@ save registers on stack
stmfd sp!, {r0 - r12, lr}
+ @ Drain write cache
+ mov r4, #0
+ mcr p15, 0, r0, c7, c10, 4
+ nop
+
@ load base address of Traffic Controller
- mov r4, #TCMIF_ASM_BASE & 0xff000000
- orr r4, r4, #TCMIF_ASM_BASE & 0x00ff0000
- orr r4, r4, #TCMIF_ASM_BASE & 0x0000ff00
+ mov r6, #TCMIF_ASM_BASE & 0xff000000
+ orr r6, r6, #TCMIF_ASM_BASE & 0x00ff0000
+ orr r6, r6, #TCMIF_ASM_BASE & 0x0000ff00
@ prepare to put SDRAM into self-refresh manually
- ldr r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
- orr r5, r5, #SELF_REFRESH_MODE & 0xff000000
- orr r5, r5, #SELF_REFRESH_MODE & 0x000000ff
- str r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
+ ldr r7, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
+ orr r9, r7, #SELF_REFRESH_MODE & 0xff000000
+ orr r9, r9, #SELF_REFRESH_MODE & 0x000000ff
+ str r9, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
@ prepare to put EMIFS to Sleep
- ldr r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
- orr r5, r5, #IDLE_EMIFS_REQUEST & 0xff
- str r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
+ ldr r8, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
+ orr r9, r8, #IDLE_EMIFS_REQUEST & 0xff
+ str r9, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
@ load base address of ARM_IDLECT1 and ARM_IDLECT2
mov r4, #CLKGEN_REG_ASM_BASE & 0xff000000
orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x0000ff00
@ turn off clock domains
- mov r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff00
- strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
-
- @ work around errata of OMAP1610/5912. Enable (!) peripheral
- @ clock to let the chip go into deep sleep
- ldrh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- orr r5,r5, #EN_PERCK_BIT & 0xff
+ @ do not disable PERCK (0x04)
+ mov r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff
+ orr r5, r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
- mov r3, #OMAP1610_DEEP_SLEEP_REQUEST & 0xff
- orr r3, r3, #OMAP1610_DEEP_SLEEP_REQUEST & 0xff00
+ mov r3, #OMAP1610_IDLECT1_SLEEP_VAL & 0xff
+ orr r3, r3, #OMAP1610_IDLECT1_SLEEP_VAL & 0xff00
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
- mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
-l_1610_2:
- subs r5, r5, #1
- bne l_1610_2
+ @ disable instruction cache
+ mrc p15, 0, r9, c1, c0, 0
+ bic r2, r9, #0x1000
+ mcr p15, 0, r2, c1, c0, 0
+ nop
+
/*
* Let's wait for the next wake up event to wake us up. r0 can't be
* used here because r0 holds ARM_IDLECT1
* omap1610_cpu_suspend()'s resume point.
*
* It will just start executing here, so we'll restore stuff from the
- * stack, reset the ARM_IDLECT1 and ARM_IDLECT2.
+ * stack.
*/
+ @ re-enable Icache
+ mcr p15, 0, r9, c1, c0, 0
+
+ @ reset the ARM_IDLECT1 and ARM_IDLECT2.
strh r1, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
strh r0, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
+ @ Restore EMIFF controls
+ str r7, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
+ str r8, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
+
@ restore regs and return
- ldmfd sp!, {r0 - r12, pc}
+ ldmfd sp!, {r0 - r12, pc}
ENTRY(omap1610_cpu_suspend_sz)
.word . - omap1610_cpu_suspend
--- /dev/null
+/*
+ * linux/arch/arm/plat-omap/sram.S
+ *
+ * Functions that need to be run in internal SRAM
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/config.h>
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
+
+ .text
+
+/*
+ * Reprograms ULPD and CKCTL.
+ */
+ENTRY(sram_reprogram_clock)
+ stmfd sp!, {r0 - r12, lr} @ save registers on stack
+
+ mov r2, #IO_ADDRESS(DPLL_CTL) & 0xff000000
+ orr r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x00ff0000
+ orr r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x0000ff00
+
+ mov r3, #IO_ADDRESS(ARM_CKCTL) & 0xff000000
+ orr r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x00ff0000
+ orr r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x0000ff00
+
+ tst r0, #1 << 4 @ want lock mode?
+ beq newck @ nope
+ bic r0, r0, #1 << 4 @ else clear lock bit
+ strh r0, [r2] @ set dpll into bypass mode
+ orr r0, r0, #1 << 4 @ set lock bit again
+
+newck:
+ strh r1, [r3] @ write new ckctl value
+ strh r0, [r2] @ write new dpll value
+
+ mov r4, #0x0700 @ let the clocks settle
+ orr r4, r4, #0x00ff
+delay: sub r4, r4, #1
+ cmp r4, #0
+ bne delay
+
+lock: ldrh r4, [r2], #0 @ read back dpll value
+ tst r0, #1 << 4 @ want lock mode?
+ beq out @ nope
+ tst r4, #1 << 0 @ dpll rate locked?
+ beq lock @ try again
+
+out:
+ ldmfd sp!, {r0 - r12, pc} @ restore regs and return
+ENTRY(sram_reprogram_clock_sz)
+ .word . - sram_reprogram_clock
--- /dev/null
+/*
+ * linux/arch/arm/plat-omap/sram.c
+ *
+ * OMAP SRAM detection and management
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Written by Tony Lindgren <tony@atomide.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/mach/map.h>
+#include <asm/io.h>
+#include <asm/cacheflush.h>
+
+#include "sram.h"
+
+#define OMAP1_SRAM_BASE 0xd0000000
+#define OMAP1_SRAM_START 0x20000000
+#define SRAM_BOOTLOADER_SZ 0x80
+
+static unsigned long omap_sram_base;
+static unsigned long omap_sram_size;
+static unsigned long omap_sram_ceil;
+
+/*
+ * The amount of SRAM depends on the core type:
+ * 730 = 200K, 1510 = 512K, 5912 = 256K, 1610 = 16K, 1710 = 16K
+ * Note that we cannot try to test for SRAM here because writes
+ * to secure SRAM will hang the system. Also the SRAM is not
+ * yet mapped at this point.
+ */
+void __init omap_detect_sram(void)
+{
+ omap_sram_base = OMAP1_SRAM_BASE;
+
+ if (cpu_is_omap730())
+ omap_sram_size = 0x32000;
+ else if (cpu_is_omap1510())
+ omap_sram_size = 0x80000;
+ else if (cpu_is_omap1610() || cpu_is_omap1621() || cpu_is_omap1710())
+ omap_sram_size = 0x4000;
+ else if (cpu_is_omap1611())
+ omap_sram_size = 0x3e800;
+ else {
+ printk(KERN_ERR "Could not detect SRAM size\n");
+ omap_sram_size = 0x4000;
+ }
+
+ printk(KERN_INFO "SRAM size: 0x%lx\n", omap_sram_size);
+ omap_sram_ceil = omap_sram_base + omap_sram_size;
+}
+
+static struct map_desc omap_sram_io_desc[] __initdata = {
+ { OMAP1_SRAM_BASE, OMAP1_SRAM_START, 0, MT_DEVICE }
+};
+
+/*
+ * In order to use last 2kB of SRAM on 1611b, we must round the size
+ * up to multiple of PAGE_SIZE. We cannot use ioremap for SRAM, as
+ * clock init needs SRAM early.
+ */
+void __init omap_map_sram(void)
+{
+ if (omap_sram_size == 0)
+ return;
+
+ omap_sram_io_desc[0].length = (omap_sram_size + PAGE_SIZE-1)/PAGE_SIZE;
+ omap_sram_io_desc[0].length *= PAGE_SIZE;
+ iotable_init(omap_sram_io_desc, ARRAY_SIZE(omap_sram_io_desc));
+
+ /*
+ * Looks like we need to preserve some bootloader code at the
+ * beginning of SRAM for jumping to flash for reboot to work...
+ */
+ memset((void *)omap_sram_base + SRAM_BOOTLOADER_SZ, 0,
+ omap_sram_size - SRAM_BOOTLOADER_SZ);
+}
+
+static void (*_omap_sram_reprogram_clock)(u32 dpllctl, u32 ckctl) = NULL;
+
+void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl)
+{
+ if (_omap_sram_reprogram_clock == NULL)
+ panic("Cannot use SRAM");
+
+ return _omap_sram_reprogram_clock(dpllctl, ckctl);
+}
+
+void * omap_sram_push(void * start, unsigned long size)
+{
+ if (size > (omap_sram_ceil - (omap_sram_base + SRAM_BOOTLOADER_SZ))) {
+ printk(KERN_ERR "Not enough space in SRAM\n");
+ return NULL;
+ }
+ omap_sram_ceil -= size;
+ omap_sram_ceil &= ~0x3;
+ memcpy((void *)omap_sram_ceil, start, size);
+
+ return (void *)omap_sram_ceil;
+}
+
+void __init omap_sram_init(void)
+{
+ omap_detect_sram();
+ omap_map_sram();
+ _omap_sram_reprogram_clock = omap_sram_push(sram_reprogram_clock,
+ sram_reprogram_clock_sz);
+}
--- /dev/null
+/*
+ * linux/arch/arm/plat-omap/sram.h
+ *
+ * Interface for functions that need to be run in internal SRAM
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ARCH_ARM_OMAP_SRAM_H
+#define __ARCH_ARM_OMAP_SRAM_H
+
+extern void * omap_sram_push(void * start, unsigned long size);
+extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl);
+
+/* Do not use these */
+extern void sram_reprogram_clock(u32 ckctl, u32 dpllctl);
+extern unsigned long sram_reprogram_clock_sz;
+
+#endif
/* These routines should handle the standard chip-specific modes
* for usb0/1/2 ports, covering basic mux and transceiver setup.
+ * Call omap_usb_init() once, from INIT_MACHINE().
*
* Some board-*.c files will need to set up additional mux options,
* like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff