#include <asm/e820.h>
#include <asm/mce.h>
#include <asm/io.h>
+#include <asm/i387.h>
/*G:010 Welcome to the Guest!
*
lg-y = core.o hypercalls.o page_tables.o interrupts_and_traps.o \
segments.o io.o lguest_user.o
-lg-$(CONFIG_X86_32) += x86/switcher_32.o
+lg-$(CONFIG_X86_32) += x86/switcher_32.o x86/core.o
Preparation Preparation!: PREFIX=P
Guest: PREFIX=G
#include <linux/vmalloc.h>
#include <linux/cpu.h>
#include <linux/freezer.h>
+#include <linux/highmem.h>
#include <asm/paravirt.h>
-#include <asm/desc.h>
#include <asm/pgtable.h>
#include <asm/uaccess.h>
#include <asm/poll.h>
-#include <asm/highmem.h>
#include <asm/asm-offsets.h>
-#include <asm/i387.h>
#include "lg.h"
-/* Found in switcher.S */
-extern char start_switcher_text[], end_switcher_text[], switch_to_guest[];
-extern unsigned long default_idt_entries[];
-
-/* Every guest maps the core switcher code. */
-#define SHARED_SWITCHER_PAGES \
- DIV_ROUND_UP(end_switcher_text - start_switcher_text, PAGE_SIZE)
-/* Pages for switcher itself, then two pages per cpu */
-#define TOTAL_SWITCHER_PAGES (SHARED_SWITCHER_PAGES + 2 * NR_CPUS)
-
-/* We map at -4M for ease of mapping into the guest (one PTE page). */
-#define SWITCHER_ADDR 0xFFC00000
static struct vm_struct *switcher_vma;
static struct page **switcher_page;
-static int cpu_had_pge;
-static struct {
- unsigned long offset;
- unsigned short segment;
-} lguest_entry;
-
/* This One Big lock protects all inter-guest data structures. */
DEFINE_MUTEX(lguest_lock);
-static DEFINE_PER_CPU(struct lguest *, last_guest);
-
-/* Offset from where switcher.S was compiled to where we've copied it */
-static unsigned long switcher_offset(void)
-{
- return SWITCHER_ADDR - (unsigned long)start_switcher_text;
-}
-
-/* This cpu's struct lguest_pages. */
-static struct lguest_pages *lguest_pages(unsigned int cpu)
-{
- return &(((struct lguest_pages *)
- (SWITCHER_ADDR + SHARED_SWITCHER_PAGES*PAGE_SIZE))[cpu]);
-}
/*H:010 We need to set up the Switcher at a high virtual address. Remember the
* Switcher is a few hundred bytes of assembler code which actually changes the
* Host since it will be running as the switchover occurs.
*
* Trying to map memory at a particular address is an unusual thing to do, so
- * it's not a simple one-liner. We also set up the per-cpu parts of the
- * Switcher here.
- */
+ * it's not a simple one-liner. */
static __init int map_switcher(void)
{
int i, err;
goto free_vma;
}
- /* Now the switcher is mapped at the right address, we can't fail!
- * Copy in the compiled-in Switcher code (from switcher.S). */
+ /* Now the Switcher is mapped at the right address, we can't fail!
+ * Copy in the compiled-in Switcher code (from <arch>_switcher.S). */
memcpy(switcher_vma->addr, start_switcher_text,
end_switcher_text - start_switcher_text);
- /* Most of the switcher.S doesn't care that it's been moved; on Intel,
- * jumps are relative, and it doesn't access any references to external
- * code or data.
- *
- * The only exception is the interrupt handlers in switcher.S: their
- * addresses are placed in a table (default_idt_entries), so we need to
- * update the table with the new addresses. switcher_offset() is a
- * convenience function which returns the distance between the builtin
- * switcher code and the high-mapped copy we just made. */
- for (i = 0; i < IDT_ENTRIES; i++)
- default_idt_entries[i] += switcher_offset();
-
- /*
- * Set up the Switcher's per-cpu areas.
- *
- * Each CPU gets two pages of its own within the high-mapped region
- * (aka. "struct lguest_pages"). Much of this can be initialized now,
- * but some depends on what Guest we are running (which is set up in
- * copy_in_guest_info()).
- */
- for_each_possible_cpu(i) {
- /* lguest_pages() returns this CPU's two pages. */
- struct lguest_pages *pages = lguest_pages(i);
- /* This is a convenience pointer to make the code fit one
- * statement to a line. */
- struct lguest_ro_state *state = &pages->state;
-
- /* The Global Descriptor Table: the Host has a different one
- * for each CPU. We keep a descriptor for the GDT which says
- * where it is and how big it is (the size is actually the last
- * byte, not the size, hence the "-1"). */
- state->host_gdt_desc.size = GDT_SIZE-1;
- state->host_gdt_desc.address = (long)get_cpu_gdt_table(i);
-
- /* All CPUs on the Host use the same Interrupt Descriptor
- * Table, so we just use store_idt(), which gets this CPU's IDT
- * descriptor. */
- store_idt(&state->host_idt_desc);
-
- /* The descriptors for the Guest's GDT and IDT can be filled
- * out now, too. We copy the GDT & IDT into ->guest_gdt and
- * ->guest_idt before actually running the Guest. */
- state->guest_idt_desc.size = sizeof(state->guest_idt)-1;
- state->guest_idt_desc.address = (long)&state->guest_idt;
- state->guest_gdt_desc.size = sizeof(state->guest_gdt)-1;
- state->guest_gdt_desc.address = (long)&state->guest_gdt;
-
- /* We know where we want the stack to be when the Guest enters
- * the switcher: in pages->regs. The stack grows upwards, so
- * we start it at the end of that structure. */
- state->guest_tss.esp0 = (long)(&pages->regs + 1);
- /* And this is the GDT entry to use for the stack: we keep a
- * couple of special LGUEST entries. */
- state->guest_tss.ss0 = LGUEST_DS;
-
- /* x86 can have a finegrained bitmap which indicates what I/O
- * ports the process can use. We set it to the end of our
- * structure, meaning "none". */
- state->guest_tss.io_bitmap_base = sizeof(state->guest_tss);
-
- /* Some GDT entries are the same across all Guests, so we can
- * set them up now. */
- setup_default_gdt_entries(state);
- /* Most IDT entries are the same for all Guests, too.*/
- setup_default_idt_entries(state, default_idt_entries);
-
- /* The Host needs to be able to use the LGUEST segments on this
- * CPU, too, so put them in the Host GDT. */
- get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT;
- get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT;
- }
-
- /* In the Switcher, we want the %cs segment register to use the
- * LGUEST_CS GDT entry: we've put that in the Host and Guest GDTs, so
- * it will be undisturbed when we switch. To change %cs and jump we
- * need this structure to feed to Intel's "lcall" instruction. */
- lguest_entry.offset = (long)switch_to_guest + switcher_offset();
- lguest_entry.segment = LGUEST_CS;
-
printk(KERN_INFO "lguest: mapped switcher at %p\n",
switcher_vma->addr);
/* And we succeeded... */
__free_pages(switcher_page[i], 0);
}
-/*H:130 Our Guest is usually so well behaved; it never tries to do things it
- * isn't allowed to. Unfortunately, Linux's paravirtual infrastructure isn't
- * quite complete, because it doesn't contain replacements for the Intel I/O
- * instructions. As a result, the Guest sometimes fumbles across one during
- * the boot process as it probes for various things which are usually attached
- * to a PC.
- *
- * When the Guest uses one of these instructions, we get trap #13 (General
- * Protection Fault) and come here. We see if it's one of those troublesome
- * instructions and skip over it. We return true if we did. */
-static int emulate_insn(struct lguest *lg)
-{
- u8 insn;
- unsigned int insnlen = 0, in = 0, shift = 0;
- /* The eip contains the *virtual* address of the Guest's instruction:
- * guest_pa just subtracts the Guest's page_offset. */
- unsigned long physaddr = guest_pa(lg, lg->regs->eip);
-
- /* The guest_pa() function only works for Guest kernel addresses, but
- * that's all we're trying to do anyway. */
- if (lg->regs->eip < lg->page_offset)
- return 0;
-
- /* Decoding x86 instructions is icky. */
- lgread(lg, &insn, physaddr, 1);
-
- /* 0x66 is an "operand prefix". It means it's using the upper 16 bits
- of the eax register. */
- if (insn == 0x66) {
- shift = 16;
- /* The instruction is 1 byte so far, read the next byte. */
- insnlen = 1;
- lgread(lg, &insn, physaddr + insnlen, 1);
- }
-
- /* We can ignore the lower bit for the moment and decode the 4 opcodes
- * we need to emulate. */
- switch (insn & 0xFE) {
- case 0xE4: /* in <next byte>,%al */
- insnlen += 2;
- in = 1;
- break;
- case 0xEC: /* in (%dx),%al */
- insnlen += 1;
- in = 1;
- break;
- case 0xE6: /* out %al,<next byte> */
- insnlen += 2;
- break;
- case 0xEE: /* out %al,(%dx) */
- insnlen += 1;
- break;
- default:
- /* OK, we don't know what this is, can't emulate. */
- return 0;
- }
-
- /* If it was an "IN" instruction, they expect the result to be read
- * into %eax, so we change %eax. We always return all-ones, which
- * traditionally means "there's nothing there". */
- if (in) {
- /* Lower bit tells is whether it's a 16 or 32 bit access */
- if (insn & 0x1)
- lg->regs->eax = 0xFFFFFFFF;
- else
- lg->regs->eax |= (0xFFFF << shift);
- }
- /* Finally, we've "done" the instruction, so move past it. */
- lg->regs->eip += insnlen;
- /* Success! */
- return 1;
-}
-/*:*/
-
/*L:305
* Dealing With Guest Memory.
*
}
/* (end of memory access helper routines) :*/
-static void set_ts(void)
-{
- u32 cr0;
-
- cr0 = read_cr0();
- if (!(cr0 & 8))
- write_cr0(cr0|8);
-}
-
-/*S:010
- * We are getting close to the Switcher.
- *
- * Remember that each CPU has two pages which are visible to the Guest when it
- * runs on that CPU. This has to contain the state for that Guest: we copy the
- * state in just before we run the Guest.
- *
- * Each Guest has "changed" flags which indicate what has changed in the Guest
- * since it last ran. We saw this set in interrupts_and_traps.c and
- * segments.c.
- */
-static void copy_in_guest_info(struct lguest *lg, struct lguest_pages *pages)
-{
- /* Copying all this data can be quite expensive. We usually run the
- * same Guest we ran last time (and that Guest hasn't run anywhere else
- * meanwhile). If that's not the case, we pretend everything in the
- * Guest has changed. */
- if (__get_cpu_var(last_guest) != lg || lg->last_pages != pages) {
- __get_cpu_var(last_guest) = lg;
- lg->last_pages = pages;
- lg->changed = CHANGED_ALL;
- }
-
- /* These copies are pretty cheap, so we do them unconditionally: */
- /* Save the current Host top-level page directory. */
- pages->state.host_cr3 = __pa(current->mm->pgd);
- /* Set up the Guest's page tables to see this CPU's pages (and no
- * other CPU's pages). */
- map_switcher_in_guest(lg, pages);
- /* Set up the two "TSS" members which tell the CPU what stack to use
- * for traps which do directly into the Guest (ie. traps at privilege
- * level 1). */
- pages->state.guest_tss.esp1 = lg->esp1;
- pages->state.guest_tss.ss1 = lg->ss1;
-
- /* Copy direct-to-Guest trap entries. */
- if (lg->changed & CHANGED_IDT)
- copy_traps(lg, pages->state.guest_idt, default_idt_entries);
-
- /* Copy all GDT entries which the Guest can change. */
- if (lg->changed & CHANGED_GDT)
- copy_gdt(lg, pages->state.guest_gdt);
- /* If only the TLS entries have changed, copy them. */
- else if (lg->changed & CHANGED_GDT_TLS)
- copy_gdt_tls(lg, pages->state.guest_gdt);
-
- /* Mark the Guest as unchanged for next time. */
- lg->changed = 0;
-}
-
-/* Finally: the code to actually call into the Switcher to run the Guest. */
-static void run_guest_once(struct lguest *lg, struct lguest_pages *pages)
-{
- /* This is a dummy value we need for GCC's sake. */
- unsigned int clobber;
-
- /* Copy the guest-specific information into this CPU's "struct
- * lguest_pages". */
- copy_in_guest_info(lg, pages);
-
- /* Set the trap number to 256 (impossible value). If we fault while
- * switching to the Guest (bad segment registers or bug), this will
- * cause us to abort the Guest. */
- lg->regs->trapnum = 256;
-
- /* Now: we push the "eflags" register on the stack, then do an "lcall".
- * This is how we change from using the kernel code segment to using
- * the dedicated lguest code segment, as well as jumping into the
- * Switcher.
- *
- * The lcall also pushes the old code segment (KERNEL_CS) onto the
- * stack, then the address of this call. This stack layout happens to
- * exactly match the stack of an interrupt... */
- asm volatile("pushf; lcall *lguest_entry"
- /* This is how we tell GCC that %eax ("a") and %ebx ("b")
- * are changed by this routine. The "=" means output. */
- : "=a"(clobber), "=b"(clobber)
- /* %eax contains the pages pointer. ("0" refers to the
- * 0-th argument above, ie "a"). %ebx contains the
- * physical address of the Guest's top-level page
- * directory. */
- : "0"(pages), "1"(__pa(lg->pgdirs[lg->pgdidx].pgdir))
- /* We tell gcc that all these registers could change,
- * which means we don't have to save and restore them in
- * the Switcher. */
- : "memory", "%edx", "%ecx", "%edi", "%esi");
-}
-/*:*/
-
/*H:030 Let's jump straight to the the main loop which runs the Guest.
* Remember, this is called by the Launcher reading /dev/lguest, and we keep
* going around and around until something interesting happens. */
{
/* We stop running once the Guest is dead. */
while (!lg->dead) {
- /* We need to initialize this, otherwise gcc complains. It's
- * not (yet) clever enough to see that it's initialized when we
- * need it. */
- unsigned int cr2 = 0; /* Damn gcc */
-
/* First we run any hypercalls the Guest wants done: either in
* the hypercall ring in "struct lguest_data", or directly by
* using int 31 (LGUEST_TRAP_ENTRY). */
* the "Do Not Disturb" sign: */
local_irq_disable();
- /* Remember the awfully-named TS bit? If the Guest has asked
- * to set it we set it now, so we can trap and pass that trap
- * to the Guest if it uses the FPU. */
- if (lg->ts)
- set_ts();
-
- /* SYSENTER is an optimized way of doing system calls. We
- * can't allow it because it always jumps to privilege level 0.
- * A normal Guest won't try it because we don't advertise it in
- * CPUID, but a malicious Guest (or malicious Guest userspace
- * program) could, so we tell the CPU to disable it before
- * running the Guest. */
- if (boot_cpu_has(X86_FEATURE_SEP))
- wrmsr(MSR_IA32_SYSENTER_CS, 0, 0);
-
- /* Now we actually run the Guest. It will pop back out when
- * something interesting happens, and we can examine its
- * registers to see what it was doing. */
- run_guest_once(lg, lguest_pages(raw_smp_processor_id()));
-
- /* The "regs" pointer contains two extra entries which are not
- * really registers: a trap number which says what interrupt or
- * trap made the switcher code come back, and an error code
- * which some traps set. */
-
- /* If the Guest page faulted, then the cr2 register will tell
- * us the bad virtual address. We have to grab this now,
- * because once we re-enable interrupts an interrupt could
- * fault and thus overwrite cr2, or we could even move off to a
- * different CPU. */
- if (lg->regs->trapnum == 14)
- cr2 = read_cr2();
- /* Similarly, if we took a trap because the Guest used the FPU,
- * we have to restore the FPU it expects to see. */
- else if (lg->regs->trapnum == 7)
- math_state_restore();
-
- /* Restore SYSENTER if it's supposed to be on. */
- if (boot_cpu_has(X86_FEATURE_SEP))
- wrmsr(MSR_IA32_SYSENTER_CS, __KERNEL_CS, 0);
+ /* Actually run the Guest until something happens. */
+ lguest_arch_run_guest(lg);
/* Now we're ready to be interrupted or moved to other CPUs */
local_irq_enable();
- /* OK, so what happened? */
- switch (lg->regs->trapnum) {
- case 13: /* We've intercepted a GPF. */
- /* Check if this was one of those annoying IN or OUT
- * instructions which we need to emulate. If so, we
- * just go back into the Guest after we've done it. */
- if (lg->regs->errcode == 0) {
- if (emulate_insn(lg))
- continue;
- }
- break;
- case 14: /* We've intercepted a page fault. */
- /* The Guest accessed a virtual address that wasn't
- * mapped. This happens a lot: we don't actually set
- * up most of the page tables for the Guest at all when
- * we start: as it runs it asks for more and more, and
- * we set them up as required. In this case, we don't
- * even tell the Guest that the fault happened.
- *
- * The errcode tells whether this was a read or a
- * write, and whether kernel or userspace code. */
- if (demand_page(lg, cr2, lg->regs->errcode))
- continue;
-
- /* OK, it's really not there (or not OK): the Guest
- * needs to know. We write out the cr2 value so it
- * knows where the fault occurred.
- *
- * Note that if the Guest were really messed up, this
- * could happen before it's done the INITIALIZE
- * hypercall, so lg->lguest_data will be NULL */
- if (lg->lguest_data
- && put_user(cr2, &lg->lguest_data->cr2))
- kill_guest(lg, "Writing cr2");
- break;
- case 7: /* We've intercepted a Device Not Available fault. */
- /* If the Guest doesn't want to know, we already
- * restored the Floating Point Unit, so we just
- * continue without telling it. */
- if (!lg->ts)
- continue;
- break;
- case 32 ... 255:
- /* These values mean a real interrupt occurred, in
- * which case the Host handler has already been run.
- * We just do a friendly check if another process
- * should now be run, then fall through to loop
- * around: */
- cond_resched();
- case LGUEST_TRAP_ENTRY: /* Handled at top of loop */
- continue;
- }
-
- /* If we get here, it's a trap the Guest wants to know
- * about. */
- if (deliver_trap(lg, lg->regs->trapnum))
- continue;
-
- /* If the Guest doesn't have a handler (either it hasn't
- * registered any yet, or it's one of the faults we don't let
- * it handle), it dies with a cryptic error message. */
- kill_guest(lg, "unhandled trap %li at %#lx (%#lx)",
- lg->regs->trapnum, lg->regs->eip,
- lg->regs->trapnum == 14 ? cr2 : lg->regs->errcode);
+ /* Now we deal with whatever happened to the Guest. */
+ lguest_arch_handle_trap(lg);
}
+
/* The Guest is dead => "No such file or directory" */
return -ENOENT;
}
-/* Now we can look at each of the routines this calls, in increasing order of
- * complexity: do_hypercalls(), emulate_insn(), maybe_do_interrupt(),
- * deliver_trap() and demand_page(). After all those, we'll be ready to
- * examine the Switcher, and our philosophical understanding of the Host/Guest
- * duality will be complete. :*/
-static void adjust_pge(void *on)
-{
- if (on)
- write_cr4(read_cr4() | X86_CR4_PGE);
- else
- write_cr4(read_cr4() & ~X86_CR4_PGE);
-}
-
/*H:000
* Welcome to the Host!
*
return err;
}
- /* Finally, we need to turn off "Page Global Enable". PGE is an
- * optimization where page table entries are specially marked to show
- * they never change. The Host kernel marks all the kernel pages this
- * way because it's always present, even when userspace is running.
- *
- * Lguest breaks this: unbeknownst to the rest of the Host kernel, we
- * switch to the Guest kernel. If you don't disable this on all CPUs,
- * you'll get really weird bugs that you'll chase for two days.
- *
- * I used to turn PGE off every time we switched to the Guest and back
- * on when we return, but that slowed the Switcher down noticibly. */
-
- /* We don't need the complexity of CPUs coming and going while we're
- * doing this. */
- lock_cpu_hotplug();
- if (cpu_has_pge) { /* We have a broader idea of "global". */
- /* Remember that this was originally set (for cleanup). */
- cpu_had_pge = 1;
- /* adjust_pge is a helper function which sets or unsets the PGE
- * bit on its CPU, depending on the argument (0 == unset). */
- on_each_cpu(adjust_pge, (void *)0, 0, 1);
- /* Turn off the feature in the global feature set. */
- clear_bit(X86_FEATURE_PGE, boot_cpu_data.x86_capability);
- }
- unlock_cpu_hotplug();
+ /* Finally we do some architecture-specific setup. */
+ lguest_arch_host_init();
/* All good! */
return 0;
free_pagetables();
unmap_switcher();
- /* If we had PGE before we started, turn it back on now. */
- lock_cpu_hotplug();
- if (cpu_had_pge) {
- set_bit(X86_FEATURE_PGE, boot_cpu_data.x86_capability);
- /* adjust_pge's argument "1" means set PGE. */
- on_each_cpu(adjust_pge, (void *)1, 0, 1);
- }
- unlock_cpu_hotplug();
+ lguest_arch_host_fini();
}
+/*:*/
/* The Host side of lguest can be a module. This is a nice way for people to
* play with it. */
/* Look at the IDT entry the Guest gave us for this interrupt. The
* first 32 (FIRST_EXTERNAL_VECTOR) entries are for traps, so we skip
* over them. */
- idt = &lg->idt[FIRST_EXTERNAL_VECTOR+irq];
+ idt = &lg->arch.idt[FIRST_EXTERNAL_VECTOR+irq];
/* If they don't have a handler (yet?), we just ignore it */
if (idt_present(idt->a, idt->b)) {
/* OK, mark it no longer pending and deliver it. */
{
/* Trap numbers are always 8 bit, but we set an impossible trap number
* for traps inside the Switcher, so check that here. */
- if (num >= ARRAY_SIZE(lg->idt))
+ if (num >= ARRAY_SIZE(lg->arch.idt))
return 0;
/* Early on the Guest hasn't set the IDT entries (or maybe it put a
* bogus one in): if we fail here, the Guest will be killed. */
- if (!idt_present(lg->idt[num].a, lg->idt[num].b))
+ if (!idt_present(lg->arch.idt[num].a, lg->arch.idt[num].b))
return 0;
- set_guest_interrupt(lg, lg->idt[num].a, lg->idt[num].b, has_err(num));
+ set_guest_interrupt(lg, lg->arch.idt[num].a, lg->arch.idt[num].b, has_err(num));
return 1;
}
lg->changed |= CHANGED_IDT;
/* Check that the Guest doesn't try to step outside the bounds. */
- if (num >= ARRAY_SIZE(lg->idt))
+ if (num >= ARRAY_SIZE(lg->arch.idt))
kill_guest(lg, "Setting idt entry %u", num);
else
- set_trap(lg, &lg->idt[num], num, lo, hi);
+ set_trap(lg, &lg->arch.idt[num], num, lo, hi);
}
/* The default entry for each interrupt points into the Switcher routines which
/* We can simply copy the direct traps, otherwise we use the default
* ones in the Switcher: they will return to the Host. */
- for (i = 0; i < ARRAY_SIZE(lg->idt); i++) {
+ for (i = 0; i < ARRAY_SIZE(lg->arch.idt); i++) {
/* If no Guest can ever override this trap, leave it alone. */
if (!direct_trap(i))
continue;
* Interrupt gates (type 14) disable interrupts as they are
* entered, which we never let the Guest do. Not present
* entries (type 0x0) also can't go direct, of course. */
- if (idt_type(lg->idt[i].a, lg->idt[i].b) == 0xF)
- idt[i] = lg->idt[i];
+ if (idt_type(lg->arch.idt[i].a, lg->arch.idt[i].b) == 0xF)
+ idt[i] = lg->arch.idt[i];
else
/* Reset it to the default. */
default_idt_entry(&idt[i], i, def[i]);
#ifndef _LGUEST_H
#define _LGUEST_H
-#include <asm/desc.h>
-
-#define GDT_ENTRY_LGUEST_CS 10
-#define GDT_ENTRY_LGUEST_DS 11
-#define LGUEST_CS (GDT_ENTRY_LGUEST_CS * 8)
-#define LGUEST_DS (GDT_ENTRY_LGUEST_DS * 8)
-
#ifndef __ASSEMBLY__
#include <linux/types.h>
#include <linux/init.h>
#include <linux/wait.h>
#include <linux/err.h>
#include <asm/semaphore.h>
-#include "irq_vectors.h"
-
-#define GUEST_PL 1
-struct lguest_regs
-{
- /* Manually saved part. */
- unsigned long ebx, ecx, edx;
- unsigned long esi, edi, ebp;
- unsigned long gs;
- unsigned long eax;
- unsigned long fs, ds, es;
- unsigned long trapnum, errcode;
- /* Trap pushed part */
- unsigned long eip;
- unsigned long cs;
- unsigned long eflags;
- unsigned long esp;
- unsigned long ss;
-};
+#include <asm/lguest.h>
void free_pagetables(void);
int init_pagetables(struct page **switcher_page, unsigned int pages);
-/* Full 4G segment descriptors, suitable for CS and DS. */
-#define FULL_EXEC_SEGMENT ((struct desc_struct){0x0000ffff, 0x00cf9b00})
-#define FULL_SEGMENT ((struct desc_struct){0x0000ffff, 0x00cf9300})
-
struct lguest_dma_info
{
struct list_head list;
spgd_t *pgdir;
};
-/* This is a guest-specific page (mapped ro) into the guest. */
-struct lguest_ro_state
-{
- /* Host information we need to restore when we switch back. */
- u32 host_cr3;
- struct Xgt_desc_struct host_idt_desc;
- struct Xgt_desc_struct host_gdt_desc;
- u32 host_sp;
-
- /* Fields which are used when guest is running. */
- struct Xgt_desc_struct guest_idt_desc;
- struct Xgt_desc_struct guest_gdt_desc;
- struct i386_hw_tss guest_tss;
- struct desc_struct guest_idt[IDT_ENTRIES];
- struct desc_struct guest_gdt[GDT_ENTRIES];
-};
-
/* We have two pages shared with guests, per cpu. */
struct lguest_pages
{
/* Dead? */
const char *dead;
- /* The GDT entries copied into lguest_ro_state when running. */
- struct desc_struct gdt[GDT_ENTRIES];
-
- /* The IDT entries: some copied into lguest_ro_state when running. */
- struct desc_struct idt[IDT_ENTRIES];
+ struct lguest_arch arch;
/* Virtual clock device */
struct hrtimer hrt;
int demand_page(struct lguest *info, unsigned long cr2, int errcode);
void pin_page(struct lguest *lg, unsigned long vaddr);
+/* <arch>/core.c: */
+void lguest_arch_host_init(void);
+void lguest_arch_host_fini(void);
+void lguest_arch_run_guest(struct lguest *lg);
+void lguest_arch_handle_trap(struct lguest *lg);
+
+/* <arch>/switcher.S: */
+extern char start_switcher_text[], end_switcher_text[], switch_to_guest[];
+
/* lguest_user.c: */
int lguest_device_init(void);
void lguest_device_remove(void);
/* Segment descriptors contain a privilege level: the Guest is
* sometimes careless and leaves this as 0, even though it's
* running at privilege level 1. If so, we fix it here. */
- if ((lg->gdt[i].b & 0x00006000) == 0)
- lg->gdt[i].b |= (GUEST_PL << 13);
+ if ((lg->arch.gdt[i].b & 0x00006000) == 0)
+ lg->arch.gdt[i].b |= (GUEST_PL << 13);
/* Each descriptor has an "accessed" bit. If we don't set it
* now, the CPU will try to set it when the Guest first loads
* that entry into a segment register. But the GDT isn't
* writable by the Guest, so bad things can happen. */
- lg->gdt[i].b |= 0x00000100;
+ lg->arch.gdt[i].b |= 0x00000100;
}
}
void setup_guest_gdt(struct lguest *lg)
{
/* Start with full 0-4G segments... */
- lg->gdt[GDT_ENTRY_KERNEL_CS] = FULL_EXEC_SEGMENT;
- lg->gdt[GDT_ENTRY_KERNEL_DS] = FULL_SEGMENT;
+ lg->arch.gdt[GDT_ENTRY_KERNEL_CS] = FULL_EXEC_SEGMENT;
+ lg->arch.gdt[GDT_ENTRY_KERNEL_DS] = FULL_SEGMENT;
/* ...except the Guest is allowed to use them, so set the privilege
* level appropriately in the flags. */
- lg->gdt[GDT_ENTRY_KERNEL_CS].b |= (GUEST_PL << 13);
- lg->gdt[GDT_ENTRY_KERNEL_DS].b |= (GUEST_PL << 13);
+ lg->arch.gdt[GDT_ENTRY_KERNEL_CS].b |= (GUEST_PL << 13);
+ lg->arch.gdt[GDT_ENTRY_KERNEL_DS].b |= (GUEST_PL << 13);
}
/* Like the IDT, we never simply use the GDT the Guest gives us. We set up the
unsigned int i;
for (i = GDT_ENTRY_TLS_MIN; i <= GDT_ENTRY_TLS_MAX; i++)
- gdt[i] = lg->gdt[i];
+ gdt[i] = lg->arch.gdt[i];
}
/* This is the full version */
* replaced. See ignored_gdt() above. */
for (i = 0; i < GDT_ENTRIES; i++)
if (!ignored_gdt(i))
- gdt[i] = lg->gdt[i];
+ gdt[i] = lg->arch.gdt[i];
}
/* This is where the Guest asks us to load a new GDT (LHCALL_LOAD_GDT). */
{
/* We assume the Guest has the same number of GDT entries as the
* Host, otherwise we'd have to dynamically allocate the Guest GDT. */
- if (num > ARRAY_SIZE(lg->gdt))
+ if (num > ARRAY_SIZE(lg->arch.gdt))
kill_guest(lg, "too many gdt entries %i", num);
/* We read the whole thing in, then fix it up. */
- lgread(lg, lg->gdt, table, num * sizeof(lg->gdt[0]));
- fixup_gdt_table(lg, 0, ARRAY_SIZE(lg->gdt));
+ lgread(lg, lg->arch.gdt, table, num * sizeof(lg->arch.gdt[0]));
+ fixup_gdt_table(lg, 0, ARRAY_SIZE(lg->arch.gdt));
/* Mark that the GDT changed so the core knows it has to copy it again,
* even if the Guest is run on the same CPU. */
lg->changed |= CHANGED_GDT;
void guest_load_tls(struct lguest *lg, unsigned long gtls)
{
- struct desc_struct *tls = &lg->gdt[GDT_ENTRY_TLS_MIN];
+ struct desc_struct *tls = &lg->arch.gdt[GDT_ENTRY_TLS_MIN];
lgread(lg, tls, gtls, sizeof(*tls)*GDT_ENTRY_TLS_ENTRIES);
fixup_gdt_table(lg, GDT_ENTRY_TLS_MIN, GDT_ENTRY_TLS_MAX+1);
--- /dev/null
+/*
+ * Copyright (C) 2006, Rusty Russell <rusty@rustcorp.com.au> IBM Corporation.
+ * Copyright (C) 2007, Jes Sorensen <jes@sgi.com> SGI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
+ * NON INFRINGEMENT. See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/kernel.h>
+#include <linux/start_kernel.h>
+#include <linux/string.h>
+#include <linux/console.h>
+#include <linux/screen_info.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/cpu.h>
+#include <linux/lguest.h>
+#include <linux/lguest_launcher.h>
+#include <linux/lguest_bus.h>
+#include <asm/paravirt.h>
+#include <asm/param.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/desc.h>
+#include <asm/setup.h>
+#include <asm/lguest.h>
+#include <asm/uaccess.h>
+#include <asm/i387.h>
+#include "../lg.h"
+
+static int cpu_had_pge;
+
+static struct {
+ unsigned long offset;
+ unsigned short segment;
+} lguest_entry;
+
+/* Offset from where switcher.S was compiled to where we've copied it */
+static unsigned long switcher_offset(void)
+{
+ return SWITCHER_ADDR - (unsigned long)start_switcher_text;
+}
+
+/* This cpu's struct lguest_pages. */
+static struct lguest_pages *lguest_pages(unsigned int cpu)
+{
+ return &(((struct lguest_pages *)
+ (SWITCHER_ADDR + SHARED_SWITCHER_PAGES*PAGE_SIZE))[cpu]);
+}
+
+static DEFINE_PER_CPU(struct lguest *, last_guest);
+
+/*S:010
+ * We are getting close to the Switcher.
+ *
+ * Remember that each CPU has two pages which are visible to the Guest when it
+ * runs on that CPU. This has to contain the state for that Guest: we copy the
+ * state in just before we run the Guest.
+ *
+ * Each Guest has "changed" flags which indicate what has changed in the Guest
+ * since it last ran. We saw this set in interrupts_and_traps.c and
+ * segments.c.
+ */
+static void copy_in_guest_info(struct lguest *lg, struct lguest_pages *pages)
+{
+ /* Copying all this data can be quite expensive. We usually run the
+ * same Guest we ran last time (and that Guest hasn't run anywhere else
+ * meanwhile). If that's not the case, we pretend everything in the
+ * Guest has changed. */
+ if (__get_cpu_var(last_guest) != lg || lg->last_pages != pages) {
+ __get_cpu_var(last_guest) = lg;
+ lg->last_pages = pages;
+ lg->changed = CHANGED_ALL;
+ }
+
+ /* These copies are pretty cheap, so we do them unconditionally: */
+ /* Save the current Host top-level page directory. */
+ pages->state.host_cr3 = __pa(current->mm->pgd);
+ /* Set up the Guest's page tables to see this CPU's pages (and no
+ * other CPU's pages). */
+ map_switcher_in_guest(lg, pages);
+ /* Set up the two "TSS" members which tell the CPU what stack to use
+ * for traps which do directly into the Guest (ie. traps at privilege
+ * level 1). */
+ pages->state.guest_tss.esp1 = lg->esp1;
+ pages->state.guest_tss.ss1 = lg->ss1;
+
+ /* Copy direct-to-Guest trap entries. */
+ if (lg->changed & CHANGED_IDT)
+ copy_traps(lg, pages->state.guest_idt, default_idt_entries);
+
+ /* Copy all GDT entries which the Guest can change. */
+ if (lg->changed & CHANGED_GDT)
+ copy_gdt(lg, pages->state.guest_gdt);
+ /* If only the TLS entries have changed, copy them. */
+ else if (lg->changed & CHANGED_GDT_TLS)
+ copy_gdt_tls(lg, pages->state.guest_gdt);
+
+ /* Mark the Guest as unchanged for next time. */
+ lg->changed = 0;
+}
+
+/* Finally: the code to actually call into the Switcher to run the Guest. */
+static void run_guest_once(struct lguest *lg, struct lguest_pages *pages)
+{
+ /* This is a dummy value we need for GCC's sake. */
+ unsigned int clobber;
+
+ /* Copy the guest-specific information into this CPU's "struct
+ * lguest_pages". */
+ copy_in_guest_info(lg, pages);
+
+ /* Set the trap number to 256 (impossible value). If we fault while
+ * switching to the Guest (bad segment registers or bug), this will
+ * cause us to abort the Guest. */
+ lg->regs->trapnum = 256;
+
+ /* Now: we push the "eflags" register on the stack, then do an "lcall".
+ * This is how we change from using the kernel code segment to using
+ * the dedicated lguest code segment, as well as jumping into the
+ * Switcher.
+ *
+ * The lcall also pushes the old code segment (KERNEL_CS) onto the
+ * stack, then the address of this call. This stack layout happens to
+ * exactly match the stack of an interrupt... */
+ asm volatile("pushf; lcall *lguest_entry"
+ /* This is how we tell GCC that %eax ("a") and %ebx ("b")
+ * are changed by this routine. The "=" means output. */
+ : "=a"(clobber), "=b"(clobber)
+ /* %eax contains the pages pointer. ("0" refers to the
+ * 0-th argument above, ie "a"). %ebx contains the
+ * physical address of the Guest's top-level page
+ * directory. */
+ : "0"(pages), "1"(__pa(lg->pgdirs[lg->pgdidx].pgdir))
+ /* We tell gcc that all these registers could change,
+ * which means we don't have to save and restore them in
+ * the Switcher. */
+ : "memory", "%edx", "%ecx", "%edi", "%esi");
+}
+/*:*/
+
+/*H:040 This is the i386-specific code to setup and run the Guest. Interrupts
+ * are disabled: we own the CPU. */
+void lguest_arch_run_guest(struct lguest *lg)
+{
+ /* Remember the awfully-named TS bit? If the Guest has asked
+ * to set it we set it now, so we can trap and pass that trap
+ * to the Guest if it uses the FPU. */
+ if (lg->ts)
+ lguest_set_ts();
+
+ /* SYSENTER is an optimized way of doing system calls. We
+ * can't allow it because it always jumps to privilege level 0.
+ * A normal Guest won't try it because we don't advertise it in
+ * CPUID, but a malicious Guest (or malicious Guest userspace
+ * program) could, so we tell the CPU to disable it before
+ * running the Guest. */
+ if (boot_cpu_has(X86_FEATURE_SEP))
+ wrmsr(MSR_IA32_SYSENTER_CS, 0, 0);
+
+ /* Now we actually run the Guest. It will pop back out when
+ * something interesting happens, and we can examine its
+ * registers to see what it was doing. */
+ run_guest_once(lg, lguest_pages(raw_smp_processor_id()));
+
+ /* The "regs" pointer contains two extra entries which are not
+ * really registers: a trap number which says what interrupt or
+ * trap made the switcher code come back, and an error code
+ * which some traps set. */
+
+ /* If the Guest page faulted, then the cr2 register will tell
+ * us the bad virtual address. We have to grab this now,
+ * because once we re-enable interrupts an interrupt could
+ * fault and thus overwrite cr2, or we could even move off to a
+ * different CPU. */
+ if (lg->regs->trapnum == 14)
+ lg->arch.last_pagefault = read_cr2();
+ /* Similarly, if we took a trap because the Guest used the FPU,
+ * we have to restore the FPU it expects to see. */
+ else if (lg->regs->trapnum == 7)
+ math_state_restore();
+
+ /* Restore SYSENTER if it's supposed to be on. */
+ if (boot_cpu_has(X86_FEATURE_SEP))
+ wrmsr(MSR_IA32_SYSENTER_CS, __KERNEL_CS, 0);
+}
+
+/*H:130 Our Guest is usually so well behaved; it never tries to do things it
+ * isn't allowed to. Unfortunately, Linux's paravirtual infrastructure isn't
+ * quite complete, because it doesn't contain replacements for the Intel I/O
+ * instructions. As a result, the Guest sometimes fumbles across one during
+ * the boot process as it probes for various things which are usually attached
+ * to a PC.
+ *
+ * When the Guest uses one of these instructions, we get trap #13 (General
+ * Protection Fault) and come here. We see if it's one of those troublesome
+ * instructions and skip over it. We return true if we did. */
+static int emulate_insn(struct lguest *lg)
+{
+ u8 insn;
+ unsigned int insnlen = 0, in = 0, shift = 0;
+ /* The eip contains the *virtual* address of the Guest's instruction:
+ * guest_pa just subtracts the Guest's page_offset. */
+ unsigned long physaddr = guest_pa(lg, lg->regs->eip);
+
+ /* The guest_pa() function only works for Guest kernel addresses, but
+ * that's all we're trying to do anyway. */
+ if (lg->regs->eip < lg->page_offset)
+ return 0;
+
+ /* Decoding x86 instructions is icky. */
+ lgread(lg, &insn, physaddr, 1);
+
+ /* 0x66 is an "operand prefix". It means it's using the upper 16 bits
+ of the eax register. */
+ if (insn == 0x66) {
+ shift = 16;
+ /* The instruction is 1 byte so far, read the next byte. */
+ insnlen = 1;
+ lgread(lg, &insn, physaddr + insnlen, 1);
+ }
+
+ /* We can ignore the lower bit for the moment and decode the 4 opcodes
+ * we need to emulate. */
+ switch (insn & 0xFE) {
+ case 0xE4: /* in <next byte>,%al */
+ insnlen += 2;
+ in = 1;
+ break;
+ case 0xEC: /* in (%dx),%al */
+ insnlen += 1;
+ in = 1;
+ break;
+ case 0xE6: /* out %al,<next byte> */
+ insnlen += 2;
+ break;
+ case 0xEE: /* out %al,(%dx) */
+ insnlen += 1;
+ break;
+ default:
+ /* OK, we don't know what this is, can't emulate. */
+ return 0;
+ }
+
+ /* If it was an "IN" instruction, they expect the result to be read
+ * into %eax, so we change %eax. We always return all-ones, which
+ * traditionally means "there's nothing there". */
+ if (in) {
+ /* Lower bit tells is whether it's a 16 or 32 bit access */
+ if (insn & 0x1)
+ lg->regs->eax = 0xFFFFFFFF;
+ else
+ lg->regs->eax |= (0xFFFF << shift);
+ }
+ /* Finally, we've "done" the instruction, so move past it. */
+ lg->regs->eip += insnlen;
+ /* Success! */
+ return 1;
+}
+
+/*H:050 Once we've re-enabled interrupts, we look at why the Guest exited. */
+void lguest_arch_handle_trap(struct lguest *lg)
+{
+ switch (lg->regs->trapnum) {
+ case 13: /* We've intercepted a GPF. */
+ /* Check if this was one of those annoying IN or OUT
+ * instructions which we need to emulate. If so, we
+ * just go back into the Guest after we've done it. */
+ if (lg->regs->errcode == 0) {
+ if (emulate_insn(lg))
+ return;
+ }
+ break;
+ case 14: /* We've intercepted a page fault. */
+ /* The Guest accessed a virtual address that wasn't
+ * mapped. This happens a lot: we don't actually set
+ * up most of the page tables for the Guest at all when
+ * we start: as it runs it asks for more and more, and
+ * we set them up as required. In this case, we don't
+ * even tell the Guest that the fault happened.
+ *
+ * The errcode tells whether this was a read or a
+ * write, and whether kernel or userspace code. */
+ if (demand_page(lg, lg->arch.last_pagefault, lg->regs->errcode))
+ return;
+
+ /* OK, it's really not there (or not OK): the Guest
+ * needs to know. We write out the cr2 value so it
+ * knows where the fault occurred.
+ *
+ * Note that if the Guest were really messed up, this
+ * could happen before it's done the INITIALIZE
+ * hypercall, so lg->lguest_data will be NULL */
+ if (lg->lguest_data &&
+ put_user(lg->arch.last_pagefault, &lg->lguest_data->cr2))
+ kill_guest(lg, "Writing cr2");
+ break;
+ case 7: /* We've intercepted a Device Not Available fault. */
+ /* If the Guest doesn't want to know, we already
+ * restored the Floating Point Unit, so we just
+ * continue without telling it. */
+ if (!lg->ts)
+ return;
+ break;
+ case 32 ... 255:
+ /* These values mean a real interrupt occurred, in
+ * which case the Host handler has already been run.
+ * We just do a friendly check if another process
+ * should now be run, then fall through to loop
+ * around: */
+ cond_resched();
+ case LGUEST_TRAP_ENTRY: /* Handled before re-entering Guest */
+ return;
+ }
+
+ /* We didn't handle the trap, so it needs to go to the Guest. */
+ if (!deliver_trap(lg, lg->regs->trapnum))
+ /* If the Guest doesn't have a handler (either it hasn't
+ * registered any yet, or it's one of the faults we don't let
+ * it handle), it dies with a cryptic error message. */
+ kill_guest(lg, "unhandled trap %li at %#lx (%#lx)",
+ lg->regs->trapnum, lg->regs->eip,
+ lg->regs->trapnum == 14 ? lg->arch.last_pagefault
+ : lg->regs->errcode);
+}
+
+/* Now we can look at each of the routines this calls, in increasing order of
+ * complexity: do_hypercalls(), emulate_insn(), maybe_do_interrupt(),
+ * deliver_trap() and demand_page(). After all those, we'll be ready to
+ * examine the Switcher, and our philosophical understanding of the Host/Guest
+ * duality will be complete. :*/
+static void adjust_pge(void *on)
+{
+ if (on)
+ write_cr4(read_cr4() | X86_CR4_PGE);
+ else
+ write_cr4(read_cr4() & ~X86_CR4_PGE);
+}
+
+/*H:020 Now the Switcher is mapped and every thing else is ready, we need to do
+ * some more i386-specific initialization. */
+void __init lguest_arch_host_init(void)
+{
+ int i;
+
+ /* Most of the i386/switcher.S doesn't care that it's been moved; on
+ * Intel, jumps are relative, and it doesn't access any references to
+ * external code or data.
+ *
+ * The only exception is the interrupt handlers in switcher.S: their
+ * addresses are placed in a table (default_idt_entries), so we need to
+ * update the table with the new addresses. switcher_offset() is a
+ * convenience function which returns the distance between the builtin
+ * switcher code and the high-mapped copy we just made. */
+ for (i = 0; i < IDT_ENTRIES; i++)
+ default_idt_entries[i] += switcher_offset();
+
+ /*
+ * Set up the Switcher's per-cpu areas.
+ *
+ * Each CPU gets two pages of its own within the high-mapped region
+ * (aka. "struct lguest_pages"). Much of this can be initialized now,
+ * but some depends on what Guest we are running (which is set up in
+ * copy_in_guest_info()).
+ */
+ for_each_possible_cpu(i) {
+ /* lguest_pages() returns this CPU's two pages. */
+ struct lguest_pages *pages = lguest_pages(i);
+ /* This is a convenience pointer to make the code fit one
+ * statement to a line. */
+ struct lguest_ro_state *state = &pages->state;
+
+ /* The Global Descriptor Table: the Host has a different one
+ * for each CPU. We keep a descriptor for the GDT which says
+ * where it is and how big it is (the size is actually the last
+ * byte, not the size, hence the "-1"). */
+ state->host_gdt_desc.size = GDT_SIZE-1;
+ state->host_gdt_desc.address = (long)get_cpu_gdt_table(i);
+
+ /* All CPUs on the Host use the same Interrupt Descriptor
+ * Table, so we just use store_idt(), which gets this CPU's IDT
+ * descriptor. */
+ store_idt(&state->host_idt_desc);
+
+ /* The descriptors for the Guest's GDT and IDT can be filled
+ * out now, too. We copy the GDT & IDT into ->guest_gdt and
+ * ->guest_idt before actually running the Guest. */
+ state->guest_idt_desc.size = sizeof(state->guest_idt)-1;
+ state->guest_idt_desc.address = (long)&state->guest_idt;
+ state->guest_gdt_desc.size = sizeof(state->guest_gdt)-1;
+ state->guest_gdt_desc.address = (long)&state->guest_gdt;
+
+ /* We know where we want the stack to be when the Guest enters
+ * the switcher: in pages->regs. The stack grows upwards, so
+ * we start it at the end of that structure. */
+ state->guest_tss.esp0 = (long)(&pages->regs + 1);
+ /* And this is the GDT entry to use for the stack: we keep a
+ * couple of special LGUEST entries. */
+ state->guest_tss.ss0 = LGUEST_DS;
+
+ /* x86 can have a finegrained bitmap which indicates what I/O
+ * ports the process can use. We set it to the end of our
+ * structure, meaning "none". */
+ state->guest_tss.io_bitmap_base = sizeof(state->guest_tss);
+
+ /* Some GDT entries are the same across all Guests, so we can
+ * set them up now. */
+ setup_default_gdt_entries(state);
+ /* Most IDT entries are the same for all Guests, too.*/
+ setup_default_idt_entries(state, default_idt_entries);
+
+ /* The Host needs to be able to use the LGUEST segments on this
+ * CPU, too, so put them in the Host GDT. */
+ get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT;
+ get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT;
+ }
+
+ /* In the Switcher, we want the %cs segment register to use the
+ * LGUEST_CS GDT entry: we've put that in the Host and Guest GDTs, so
+ * it will be undisturbed when we switch. To change %cs and jump we
+ * need this structure to feed to Intel's "lcall" instruction. */
+ lguest_entry.offset = (long)switch_to_guest + switcher_offset();
+ lguest_entry.segment = LGUEST_CS;
+
+ /* Finally, we need to turn off "Page Global Enable". PGE is an
+ * optimization where page table entries are specially marked to show
+ * they never change. The Host kernel marks all the kernel pages this
+ * way because it's always present, even when userspace is running.
+ *
+ * Lguest breaks this: unbeknownst to the rest of the Host kernel, we
+ * switch to the Guest kernel. If you don't disable this on all CPUs,
+ * you'll get really weird bugs that you'll chase for two days.
+ *
+ * I used to turn PGE off every time we switched to the Guest and back
+ * on when we return, but that slowed the Switcher down noticibly. */
+
+ /* We don't need the complexity of CPUs coming and going while we're
+ * doing this. */
+ lock_cpu_hotplug();
+ if (cpu_has_pge) { /* We have a broader idea of "global". */
+ /* Remember that this was originally set (for cleanup). */
+ cpu_had_pge = 1;
+ /* adjust_pge is a helper function which sets or unsets the PGE
+ * bit on its CPU, depending on the argument (0 == unset). */
+ on_each_cpu(adjust_pge, (void *)0, 0, 1);
+ /* Turn off the feature in the global feature set. */
+ clear_bit(X86_FEATURE_PGE, boot_cpu_data.x86_capability);
+ }
+ unlock_cpu_hotplug();
+};
+/*:*/
+
+void __exit lguest_arch_host_fini(void)
+{
+ /* If we had PGE before we started, turn it back on now. */
+ lock_cpu_hotplug();
+ if (cpu_had_pge) {
+ set_bit(X86_FEATURE_PGE, boot_cpu_data.x86_capability);
+ /* adjust_pge's argument "1" means set PGE. */
+ on_each_cpu(adjust_pge, (void *)1, 0, 1);
+ }
+ unlock_cpu_hotplug();
+}
#include <linux/linkage.h>
#include <asm/asm-offsets.h>
#include <asm/page.h>
-#include "../lg.h"
+#include <asm/segment.h>
+#include <asm/lguest.h>
// We mark the start of the code to copy
// It's placed in .text tho it's never run here
--- /dev/null
+#ifndef _X86_LGUEST_H
+#define _X86_LGUEST_H
+
+#define GDT_ENTRY_LGUEST_CS 10
+#define GDT_ENTRY_LGUEST_DS 11
+#define LGUEST_CS (GDT_ENTRY_LGUEST_CS * 8)
+#define LGUEST_DS (GDT_ENTRY_LGUEST_DS * 8)
+
+#ifndef __ASSEMBLY__
+#include <asm/desc.h>
+
+#define GUEST_PL 1
+
+/* Every guest maps the core switcher code. */
+#define SHARED_SWITCHER_PAGES \
+ DIV_ROUND_UP(end_switcher_text - start_switcher_text, PAGE_SIZE)
+/* Pages for switcher itself, then two pages per cpu */
+#define TOTAL_SWITCHER_PAGES (SHARED_SWITCHER_PAGES + 2 * NR_CPUS)
+
+/* We map at -4M for ease of mapping into the guest (one PTE page). */
+#define SWITCHER_ADDR 0xFFC00000
+
+/* Found in switcher.S */
+extern unsigned long default_idt_entries[];
+
+struct lguest_regs
+{
+ /* Manually saved part. */
+ unsigned long ebx, ecx, edx;
+ unsigned long esi, edi, ebp;
+ unsigned long gs;
+ unsigned long eax;
+ unsigned long fs, ds, es;
+ unsigned long trapnum, errcode;
+ /* Trap pushed part */
+ unsigned long eip;
+ unsigned long cs;
+ unsigned long eflags;
+ unsigned long esp;
+ unsigned long ss;
+};
+
+/* This is a guest-specific page (mapped ro) into the guest. */
+struct lguest_ro_state
+{
+ /* Host information we need to restore when we switch back. */
+ u32 host_cr3;
+ struct Xgt_desc_struct host_idt_desc;
+ struct Xgt_desc_struct host_gdt_desc;
+ u32 host_sp;
+
+ /* Fields which are used when guest is running. */
+ struct Xgt_desc_struct guest_idt_desc;
+ struct Xgt_desc_struct guest_gdt_desc;
+ struct i386_hw_tss guest_tss;
+ struct desc_struct guest_idt[IDT_ENTRIES];
+ struct desc_struct guest_gdt[GDT_ENTRIES];
+};
+
+struct lguest_arch
+{
+ /* The GDT entries copied into lguest_ro_state when running. */
+ struct desc_struct gdt[GDT_ENTRIES];
+
+ /* The IDT entries: some copied into lguest_ro_state when running. */
+ struct desc_struct idt[IDT_ENTRIES];
+
+ /* The address of the last guest-visible pagefault (ie. cr2). */
+ unsigned long last_pagefault;
+};
+
+static inline void lguest_set_ts(void)
+{
+ u32 cr0;
+
+ cr0 = read_cr0();
+ if (!(cr0 & 8))
+ write_cr0(cr0|8);
+}
+
+/* Full 4G segment descriptors, suitable for CS and DS. */
+#define FULL_EXEC_SEGMENT ((struct desc_struct){0x0000ffff, 0x00cf9b00})
+#define FULL_SEGMENT ((struct desc_struct){0x0000ffff, 0x00cf9300})
+
+#endif /* __ASSEMBLY__ */
+
+#endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff