[Blackfin] arch: add Blackfin on-chip SIR IrDA driver support

 - add platform device resources in board files
 - add new bfin_sir.h to each machines

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

diff --git a/arch/blackfin/kernel/bfin_dma_5xx.c b/arch/blackfin/kernel/bfin_dma_5xx.c
index 18fc8a8..df4d2a5 100644 (file)
--- a/arch/blackfin/kernel/bfin_dma_5xx.c
+++ b/arch/blackfin/kernel/bfin_dma_5xx.c
@@ -108,10 +108,10 @@ int request_dma(unsigned int channel, char *device_id)
        if (channel >= CH_UART2_RX && channel <= CH_UART3_TX) {
                if (strncmp(device_id, "BFIN_UART", 9) == 0)
                        dma_ch[channel].regs->peripheral_map |=
-                               (channel - CH_UART2_RX + 0xC);
+                               ((channel - CH_UART2_RX + 0xC)<<12);
                else
                        dma_ch[channel].regs->peripheral_map |=
-                               (channel - CH_UART2_RX + 0x6);
+                               ((channel - CH_UART2_RX + 0x6)<<12);
        }
 #endif
 

diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index be20f79..583d538 100644 (file)
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -707,6 +707,32 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 static struct resource bfin_twi0_resource[] = {
        [0] = {
@@ -874,6 +900,10 @@ static struct platform_device *stamp_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
        &i2c_bfin_twi_device,
 #endif

diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index 39c3dd3..7cc4864 100644 (file)
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -304,6 +304,25 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
 
 #include <linux/serial_8250.h>
@@ -403,6 +422,10 @@ static struct platform_device *h8606_devices[] __initdata = {
        &serial8250_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE)
        &opencores_kbd_device,
 #endif

diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index 7e7b7c9..a03149c 100644 (file)
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -234,6 +234,25 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 static struct platform_device bfin_sport0_uart_device = {
        .name = "bfin-sport-uart",
@@ -327,6 +346,10 @@ static struct platform_device *cm_bf533_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
        &bfin_sport0_uart_device,
        &bfin_sport1_uart_device,

diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
index 35c1efd..08a7943 100644 (file)
--- a/arch/blackfin/mach-bf533/boards/ezkit.c
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -237,6 +237,25 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 #define PATA_INT       55
 
@@ -352,6 +371,10 @@ static struct platform_device *ezkit_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
        &bfin_pata_device,
 #endif

diff --git a/arch/blackfin/mach-bf533/boards/ip0x.c b/arch/blackfin/mach-bf533/boards/ip0x.c
index 4af6147..5864892 100644 (file)
--- a/arch/blackfin/mach-bf533/boards/ip0x.c
+++ b/arch/blackfin/mach-bf533/boards/ip0x.c
@@ -196,6 +196,25 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 static struct resource isp1362_hcd_resources[] = {
        {
@@ -251,6 +270,11 @@ static struct platform_device *ip0x_devices[] __initdata = {
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
        &bfin_uart_device,
 #endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
        &isp1362_hcd_device,
 #endif

diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index 3a727d3..fddce32 100644 (file)
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -370,6 +370,25 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 static struct platform_device bfin_sport0_uart_device = {
        .name = "bfin-sport-uart",
@@ -525,6 +544,10 @@ static struct platform_device *stamp_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
        &bfin_sport0_uart_device,
        &bfin_sport1_uart_device,

diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 199fde6..d8a23cd 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -325,6 +325,32 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 static struct resource bfin_twi0_resource[] = {
        [0] = {
@@ -415,6 +441,10 @@ static struct platform_device *cm_bf537_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
        &i2c_bfin_twi_device,
 #endif

diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c
index b3d78ea..7d25082 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/generic_board.c
+++ b/arch/blackfin/mach-bf537/boards/generic_board.c
@@ -554,6 +554,32 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 static struct resource bfin_twi0_resource[] = {
        [0] = {
@@ -674,6 +700,10 @@ static struct platform_device *stamp_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
        &i2c_bfin_twi_device,
 #endif

diff --git a/arch/blackfin/mach-bf537/boards/minotaur.c b/arch/blackfin/mach-bf537/boards/minotaur.c
index 4ea7173..18ddf7a 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/minotaur.c
+++ b/arch/blackfin/mach-bf537/boards/minotaur.c
@@ -225,6 +225,32 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 static struct resource bfin_twi0_resource[] = {
        [0] = {
@@ -284,6 +310,10 @@ static struct platform_device *minotaur_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
        &i2c_bfin_twi_device,
 #endif

diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 0b3e22b..51c3bab 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -452,6 +452,31 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
 
 static struct platform_device *stamp_devices[] __initdata = {
 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
@@ -493,6 +518,10 @@ static struct platform_device *stamp_devices[] __initdata = {
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
        &bfin_uart_device,
 #endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
 };
 
 static int __init stamp_init(void)

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index d4cbcb8..0cec14b 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -698,6 +698,32 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 static struct resource bfin_twi0_resource[] = {
        [0] = {
@@ -847,6 +873,10 @@ static struct platform_device *stamp_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
        &i2c_bfin_twi_device,
 #endif

diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c
index 1aa3c1b..e3e8479 100644 (file)
--- a/arch/blackfin/mach-bf548/boards/cm_bf548.c
+++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c
@@ -184,6 +184,46 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR2
+       {
+               .start = 0xFFC02100,
+               .end = 0xFFC021FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR3
+       {
+               .start = 0xFFC03100,
+               .end = 0xFFC031FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
 static struct resource smsc911x_resources[] = {
        {
@@ -559,6 +599,10 @@ static struct platform_device *cm_bf548_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
        &bf54x_lq043_device,
 #endif

diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index 548820d..231dfbd 100644 (file)
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -188,6 +188,46 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+               .start = 0xFFC02000,
+               .end = 0xFFC020FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR2
+       {
+               .start = 0xFFC02100,
+               .end = 0xFFC021FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR3
+       {
+               .start = 0xFFC03100,
+               .end = 0xFFC031FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
 static struct resource smsc911x_resources[] = {
        {
@@ -660,6 +700,10 @@ static struct platform_device *ezkit_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
        &bf54x_lq043_device,
 #endif

diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 4a3e085..9fd5809 100644 (file)
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -283,6 +283,25 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 #define PATA_INT       119
 
@@ -330,6 +349,10 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
        &isp1362_hcd_device,
 #endif

diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index 8eb79e5..0d74b7d 100644 (file)
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -220,6 +220,25 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir_resources),
+       .resource = bfin_sir_resources,
+};
+#endif
+
 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 static struct mtd_partition ezkit_partitions[] = {
        {
@@ -445,6 +464,10 @@ static struct platform_device *ezkit_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+       &bfin_sir_device,
+#endif
+
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
        &bfin_pata_device,
 #endif

diff --git a/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h
index c0694ec..f0ab273 100644 (file)
--- a/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h
+++ b/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h
@@ -1,22 +1,38 @@
+/*
+ * file:        include/asm-blackfin/mach-bf527/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ *     blackfin serial driver head file
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
 #include <linux/serial.h>
 #include <asm/dma.h>
 #include <asm/portmux.h>
 
-#define NR_PORTS               2
-
-#define OFFSET_THR              0x00   /* Transmit Holding register            */
-#define OFFSET_RBR              0x00   /* Receive Buffer register              */
-#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
-#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
-#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
-#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
-#define OFFSET_LCR              0x0C   /* Line Control Register                */
-#define OFFSET_MCR              0x10   /* Modem Control Register               */
-#define OFFSET_LSR              0x14   /* Line Status Register                 */
-#define OFFSET_MSR              0x18   /* Modem Status Register                */
-#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
-#define OFFSET_GCTL             0x24   /* Global Control Register              */
-
 #define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
 #define UART_GET_DLL(uart)     bfin_read16(((uart)->port.membase + OFFSET_DLL))
 #define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
@@ -92,7 +108,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
        bfin_write16(uart->port.membase + OFFSET_LSR, -1);
 }
 
-struct bfin_serial_port bfin_serial_ports[NR_PORTS];
+struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
 struct bfin_serial_res {
        unsigned long uart_base_addr;
        int uart_irq;

diff --git a/include/asm-blackfin/mach-bf527/bfin_sir.h b/include/asm-blackfin/mach-bf527/bfin_sir.h
new file mode 100644 (file)
index 0000000..0612d0c
--- /dev/null
+++ b/include/asm-blackfin/mach-bf527/bfin_sir.h
@@ -0,0 +1,133 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port)   bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port)    bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port)    bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_GET_DLH(port)    bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_IIR(port)    bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_LCR(port)    bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port)   bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v)  bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER), v)
+#define SIR_UART_PUT_DLH(port, v)  bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v)  bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+       char *buf;
+       int head;
+       int tail;
+       };
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+       unsigned char __iomem   *membase;
+       unsigned int            irq;
+       unsigned int            lsr;
+       unsigned long           clk;
+       struct net_device       *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+       int                     tx_done;
+       struct dma_rx_buf       rx_dma_buf;
+       struct timer_list       rx_dma_timer;
+       int                     rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+       unsigned int            tx_dma_channel;
+       unsigned int            rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+       unsigned long   base_addr;
+       int             irq;
+       unsigned int    rx_dma_channel;
+       unsigned int    tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+       0xFFC00400,
+       IRQ_UART0_RX,
+       CH_UART0_RX,
+       CH_UART0_TX,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+       0xFFC02000,
+       IRQ_UART1_RX,
+       CH_UART1_RX,
+       CH_UART1_TX,
+       },
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+       struct bfin_sir_port    *sir_port;
+       spinlock_t              lock;
+       unsigned int            open;
+       int                     speed;
+       int                     newspeed;
+
+       struct sk_buff          *txskb;
+       struct sk_buff          *rxskb;
+       struct net_device_stats stats;
+       struct device           *dev;
+       struct irlap_cb         *irlap;
+       struct qos_info         qos;
+
+       iobuff_t                tx_buff;
+       iobuff_t                rx_buff;
+
+       struct work_struct      work;
+       int                     mtt;
+};
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+       unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+       port->lsr |= (lsr & (BI|FE|PE|OE));
+       return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+       port->lsr = 0;
+       bfin_read16(port->membase + OFFSET_LSR);
+}
+
+#define DRIVER_NAME "bfin_sir"
+
+static void bfin_sir_hw_init(void)
+{
+#ifdef CONFIG_BFIN_SIR0
+       peripheral_request(P_UART0_TX, DRIVER_NAME);
+       peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_BFIN_SIR1
+       peripheral_request(P_UART1_TX, DRIVER_NAME);
+       peripheral_request(P_UART1_RX, DRIVER_NAME);
+#endif
+       SSYNC();
+}

diff --git a/include/asm-blackfin/mach-bf527/blackfin.h b/include/asm-blackfin/mach-bf527/blackfin.h
index 1bd07e3..2891727 100644 (file)
--- a/include/asm-blackfin/mach-bf527/blackfin.h
+++ b/include/asm-blackfin/mach-bf527/blackfin.h
@@ -64,6 +64,21 @@
 #define STATUS_P1      0x02
 #define STATUS_P0      0x01
 
+#define BFIN_UART_NR_PORTS     2
+
+#define OFFSET_THR              0x00   /* Transmit Holding register            */
+#define OFFSET_RBR              0x00   /* Receive Buffer register              */
+#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
+#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
+#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
+#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
+#define OFFSET_LCR              0x0C   /* Line Control Register                */
+#define OFFSET_MCR              0x10   /* Modem Control Register               */
+#define OFFSET_LSR              0x14   /* Line Status Register                 */
+#define OFFSET_MSR              0x18   /* Modem Status Register                */
+#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
+#define OFFSET_GCTL             0x24   /* Global Control Register              */
+
 /* DPMC*/
 #define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
 #define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)

diff --git a/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
index b6f513b..fbe88de 100644 (file)
--- a/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
+++ b/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
@@ -1,22 +1,38 @@
+/*
+ * file:        include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ *     blackfin serial driver head file
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
 #include <linux/serial.h>
 #include <asm/dma.h>
 #include <asm/portmux.h>
 
-#define NR_PORTS                1
-
-#define OFFSET_THR              0x00   /* Transmit Holding register            */
-#define OFFSET_RBR              0x00   /* Receive Buffer register              */
-#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
-#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
-#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
-#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
-#define OFFSET_LCR              0x0C   /* Line Control Register                */
-#define OFFSET_MCR              0x10   /* Modem Control Register               */
-#define OFFSET_LSR              0x14   /* Line Status Register                 */
-#define OFFSET_MSR              0x18   /* Modem Status Register                */
-#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
-#define OFFSET_GCTL             0x24   /* Global Control Register              */
-
 #define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
 #define UART_GET_DLL(uart)     bfin_read16(((uart)->port.membase + OFFSET_DLL))
 #define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
@@ -84,7 +100,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
        bfin_write16(uart->port.membase + OFFSET_LSR, -1);
 }
 
-struct bfin_serial_port bfin_serial_ports[NR_PORTS];
+struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
 struct bfin_serial_res {
        unsigned long   uart_base_addr;
        int             uart_irq;
@@ -115,7 +131,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
 
 #define DRIVER_NAME "bfin-uart"
 
-int nr_ports = NR_PORTS;
+int nr_ports = BFIN_UART_NR_PORTS;
 static void bfin_serial_hw_init(struct bfin_serial_port *uart)
 {
 

diff --git a/include/asm-blackfin/mach-bf533/bfin_sir.h b/include/asm-blackfin/mach-bf533/bfin_sir.h
new file mode 100644 (file)
index 0000000..cefcf8b
--- /dev/null
+++ b/include/asm-blackfin/mach-bf533/bfin_sir.h
@@ -0,0 +1,120 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port)   bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port)    bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port)    bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_GET_DLH(port)    bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_IIR(port)    bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_LCR(port)    bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port)   bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v)  bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER), v)
+#define SIR_UART_PUT_DLH(port, v)  bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v)  bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+       char *buf;
+       int head;
+       int tail;
+       };
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+       unsigned char __iomem   *membase;
+       unsigned int            irq;
+       unsigned int            lsr;
+       unsigned long           clk;
+       struct net_device       *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+       int                     tx_done;
+       struct dma_rx_buf       rx_dma_buf;
+       struct timer_list       rx_dma_timer;
+       int                     rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+       unsigned int            tx_dma_channel;
+       unsigned int            rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+       unsigned long   base_addr;
+       int             irq;
+       unsigned int    rx_dma_channel;
+       unsigned int    tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+       0xFFC00400,
+       IRQ_UART_RX,
+       CH_UART_RX,
+       CH_UART_TX,
+       },
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+       struct bfin_sir_port    *sir_port;
+       spinlock_t              lock;
+       unsigned int            open;
+       int                     speed;
+       int                     newspeed;
+
+       struct sk_buff          *txskb;
+       struct sk_buff          *rxskb;
+       struct net_device_stats stats;
+       struct device           *dev;
+       struct irlap_cb         *irlap;
+       struct qos_info         qos;
+
+       iobuff_t                tx_buff;
+       iobuff_t                rx_buff;
+
+       struct work_struct      work;
+       int                     mtt;
+};
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+       unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+       port->lsr |= (lsr & (BI|FE|PE|OE));
+       return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+       port->lsr = 0;
+       bfin_read16(port->membase + OFFSET_LSR);
+}
+
+#define DRIVER_NAME "bfin_sir"
+
+static void bfin_sir_hw_init(void)
+{
+#ifdef CONFIG_BFIN_SIR0
+       peripheral_request(P_UART0_TX, DRIVER_NAME);
+       peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+       SSYNC();
+}

diff --git a/include/asm-blackfin/mach-bf533/blackfin.h b/include/asm-blackfin/mach-bf533/blackfin.h
index f3b240a..d80971b 100644 (file)
--- a/include/asm-blackfin/mach-bf533/blackfin.h
+++ b/include/asm-blackfin/mach-bf533/blackfin.h
@@ -42,4 +42,19 @@
 #include "cdefBF532.h"
 #endif
 
+#define BFIN_UART_NR_PORTS      1
+
+#define OFFSET_THR              0x00   /* Transmit Holding register            */
+#define OFFSET_RBR              0x00   /* Receive Buffer register              */
+#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
+#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
+#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
+#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
+#define OFFSET_LCR              0x0C   /* Line Control Register                */
+#define OFFSET_MCR              0x10   /* Modem Control Register               */
+#define OFFSET_LSR              0x14   /* Line Status Register                 */
+#define OFFSET_MSR              0x18   /* Modem Status Register                */
+#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
+#define OFFSET_GCTL             0x24   /* Global Control Register              */
+
 #endif                         /* _MACH_BLACKFIN_H_ */

diff --git a/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h
index 8fc672d..fd100a4 100644 (file)
--- a/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h
+++ b/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h
@@ -1,22 +1,38 @@
+/*
+ * file:         include/asm-blackfin/mach-bf537/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ *     blackfin serial driver header files
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
 #include <linux/serial.h>
 #include <asm/dma.h>
 #include <asm/portmux.h>
 
-#define NR_PORTS               2
-
-#define OFFSET_THR              0x00   /* Transmit Holding register            */
-#define OFFSET_RBR              0x00   /* Receive Buffer register              */
-#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
-#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
-#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
-#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
-#define OFFSET_LCR              0x0C   /* Line Control Register                */
-#define OFFSET_MCR              0x10   /* Modem Control Register               */
-#define OFFSET_LSR              0x14   /* Line Status Register                 */
-#define OFFSET_MSR              0x18   /* Modem Status Register                */
-#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
-#define OFFSET_GCTL             0x24   /* Global Control Register              */
-
 #define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
 #define UART_GET_DLL(uart)     bfin_read16(((uart)->port.membase + OFFSET_DLL))
 #define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
@@ -92,7 +108,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
        bfin_write16(uart->port.membase + OFFSET_LSR, -1);
 }
 
-struct bfin_serial_port bfin_serial_ports[NR_PORTS];
+struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
 struct bfin_serial_res {
        unsigned long   uart_base_addr;
        int             uart_irq;

diff --git a/include/asm-blackfin/mach-bf537/bfin_sir.h b/include/asm-blackfin/mach-bf537/bfin_sir.h
new file mode 100644 (file)
index 0000000..0612d0c
--- /dev/null
+++ b/include/asm-blackfin/mach-bf537/bfin_sir.h
@@ -0,0 +1,133 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port)   bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port)    bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port)    bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_GET_DLH(port)    bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_IIR(port)    bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_LCR(port)    bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port)   bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v)  bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER), v)
+#define SIR_UART_PUT_DLH(port, v)  bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v)  bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+       char *buf;
+       int head;
+       int tail;
+       };
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+       unsigned char __iomem   *membase;
+       unsigned int            irq;
+       unsigned int            lsr;
+       unsigned long           clk;
+       struct net_device       *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+       int                     tx_done;
+       struct dma_rx_buf       rx_dma_buf;
+       struct timer_list       rx_dma_timer;
+       int                     rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+       unsigned int            tx_dma_channel;
+       unsigned int            rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+       unsigned long   base_addr;
+       int             irq;
+       unsigned int    rx_dma_channel;
+       unsigned int    tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+       0xFFC00400,
+       IRQ_UART0_RX,
+       CH_UART0_RX,
+       CH_UART0_TX,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+       0xFFC02000,
+       IRQ_UART1_RX,
+       CH_UART1_RX,
+       CH_UART1_TX,
+       },
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+       struct bfin_sir_port    *sir_port;
+       spinlock_t              lock;
+       unsigned int            open;
+       int                     speed;
+       int                     newspeed;
+
+       struct sk_buff          *txskb;
+       struct sk_buff          *rxskb;
+       struct net_device_stats stats;
+       struct device           *dev;
+       struct irlap_cb         *irlap;
+       struct qos_info         qos;
+
+       iobuff_t                tx_buff;
+       iobuff_t                rx_buff;
+
+       struct work_struct      work;
+       int                     mtt;
+};
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+       unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+       port->lsr |= (lsr & (BI|FE|PE|OE));
+       return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+       port->lsr = 0;
+       bfin_read16(port->membase + OFFSET_LSR);
+}
+
+#define DRIVER_NAME "bfin_sir"
+
+static void bfin_sir_hw_init(void)
+{
+#ifdef CONFIG_BFIN_SIR0
+       peripheral_request(P_UART0_TX, DRIVER_NAME);
+       peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_BFIN_SIR1
+       peripheral_request(P_UART1_TX, DRIVER_NAME);
+       peripheral_request(P_UART1_RX, DRIVER_NAME);
+#endif
+       SSYNC();
+}

diff --git a/include/asm-blackfin/mach-bf537/blackfin.h b/include/asm-blackfin/mach-bf537/blackfin.h
index 4f10ee0..cffc786 100644 (file)
--- a/include/asm-blackfin/mach-bf537/blackfin.h
+++ b/include/asm-blackfin/mach-bf537/blackfin.h
@@ -136,6 +136,21 @@
 #define bfin_write_UART_GCTL(val) bfin_write_UART0_GCTL(val)
 #define BFIN_UART_GCTL UART0_GCTL
 
+#define BFIN_UART_NR_PORTS     2
+
+#define OFFSET_THR              0x00   /* Transmit Holding register            */
+#define OFFSET_RBR              0x00   /* Receive Buffer register              */
+#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
+#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
+#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
+#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
+#define OFFSET_LCR              0x0C   /* Line Control Register                */
+#define OFFSET_MCR              0x10   /* Modem Control Register               */
+#define OFFSET_LSR              0x14   /* Line Status Register                 */
+#define OFFSET_MSR              0x18   /* Modem Status Register                */
+#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
+#define OFFSET_GCTL             0x24   /* Global Control Register              */
+
 /* DPMC*/
 #define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
 #define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)

diff --git a/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h
index 7e6339f..6547027 100644 (file)
--- a/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h
+++ b/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h
@@ -1,22 +1,38 @@
+/*
+ * file:        include/asm-blackfin/mach-bf548/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ *     blackfin serial driver head file
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
 #include <linux/serial.h>
 #include <asm/dma.h>
 #include <asm/portmux.h>
 
-#define NR_PORTS               4
-
-#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
-#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
-#define OFFSET_GCTL             0x08   /* Global Control Register              */
-#define OFFSET_LCR              0x0C   /* Line Control Register                */
-#define OFFSET_MCR              0x10   /* Modem Control Register               */
-#define OFFSET_LSR              0x14   /* Line Status Register                 */
-#define OFFSET_MSR              0x18   /* Modem Status Register                */
-#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
-#define OFFSET_IER_SET          0x20   /* Set Interrupt Enable Register        */
-#define OFFSET_IER_CLEAR        0x24   /* Clear Interrupt Enable Register      */
-#define OFFSET_THR              0x28   /* Transmit Holding register            */
-#define OFFSET_RBR              0x2C   /* Receive Buffer register              */
-
 #define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
 #define UART_GET_DLL(uart)     bfin_read16(((uart)->port.membase + OFFSET_DLL))
 #define UART_GET_DLH(uart)     bfin_read16(((uart)->port.membase + OFFSET_DLH))
@@ -80,7 +96,7 @@ struct bfin_serial_port {
 #endif
 };
 
-struct bfin_serial_port bfin_serial_ports[NR_PORTS];
+struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
 struct bfin_serial_res {
        unsigned long   uart_base_addr;
        int             uart_irq;

diff --git a/include/asm-blackfin/mach-bf548/bfin_sir.h b/include/asm-blackfin/mach-bf548/bfin_sir.h
new file mode 100644 (file)
index 0000000..5e94271
--- /dev/null
+++ b/include/asm-blackfin/mach-bf548/bfin_sir.h
@@ -0,0 +1,149 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port)   bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port)    bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port)    bfin_read16((port)->membase + OFFSET_IER_SET)
+#define SIR_UART_GET_DLH(port)    bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_LCR(port)    bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_LSR(port)    bfin_read16((port)->membase + OFFSET_LSR)
+#define SIR_UART_GET_GCTL(port)   bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v)  bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_SET_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER_SET), v)
+#define SIR_UART_CLEAR_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER_CLEAR), v)
+#define SIR_UART_PUT_DLH(port, v)  bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LSR(port, v)  bfin_write16(((port)->membase + OFFSET_LSR), v)
+#define SIR_UART_PUT_LCR(port, v)  bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_CLEAR_LSR(port)  bfin_write16(((port)->membase + OFFSET_LSR), -1)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+       char *buf;
+       int head;
+       int tail;
+       };
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+       unsigned char __iomem   *membase;
+       unsigned int            irq;
+       unsigned int            lsr;
+       unsigned long           clk;
+       struct net_device       *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+       int                     tx_done;
+       struct dma_rx_buf       rx_dma_buf;
+       struct timer_list       rx_dma_timer;
+       int                     rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+       unsigned int            tx_dma_channel;
+       unsigned int            rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+       unsigned long   base_addr;
+       int             irq;
+       unsigned int    rx_dma_channel;
+       unsigned int    tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+       0xFFC00400,
+       IRQ_UART0_RX,
+       CH_UART0_RX,
+       CH_UART0_TX,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+       {
+       0xFFC02000,
+       IRQ_UART1_RX,
+       CH_UART1_RX,
+       CH_UART1_TX,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR2
+       {
+       0xFFC02100,
+       IRQ_UART2_RX,
+       CH_UART2_RX,
+       CH_UART2_TX,
+       },
+#endif
+#ifdef CONFIG_BFIN_SIR3
+       {
+       0xFFC03100,
+       IRQ_UART3_RX,
+       CH_UART3_RX,
+       CH_UART3_TX,
+       },
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+       struct bfin_sir_port    *sir_port;
+       spinlock_t              lock;
+       unsigned int            open;
+       int                     speed;
+       int                     newspeed;
+
+       struct sk_buff          *txskb;
+       struct sk_buff          *rxskb;
+       struct net_device_stats stats;
+       struct device           *dev;
+       struct irlap_cb         *irlap;
+       struct qos_info         qos;
+
+       iobuff_t                tx_buff;
+       iobuff_t                rx_buff;
+
+       struct work_struct      work;
+       int                     mtt;
+};
+
+#define DRIVER_NAME "bfin_sir"
+
+static void bfin_sir_hw_init(void)
+{
+#ifdef CONFIG_BFIN_SIR0
+       peripheral_request(P_UART0_TX, DRIVER_NAME);
+       peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_BFIN_SIR1
+       peripheral_request(P_UART1_TX, DRIVER_NAME);
+       peripheral_request(P_UART1_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_BFIN_SIR2
+       peripheral_request(P_UART2_TX, DRIVER_NAME);
+       peripheral_request(P_UART2_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_BFIN_SIR3
+       peripheral_request(P_UART3_TX, DRIVER_NAME);
+       peripheral_request(P_UART3_RX, DRIVER_NAME);
+#endif
+       SSYNC();
+}

diff --git a/include/asm-blackfin/mach-bf548/blackfin.h b/include/asm-blackfin/mach-bf548/blackfin.h
index b8509c1..d6ee74a 100644 (file)
--- a/include/asm-blackfin/mach-bf548/blackfin.h
+++ b/include/asm-blackfin/mach-bf548/blackfin.h
@@ -166,6 +166,21 @@
 #define BFIN_UART_SCR                  UART1_SCR
 #define BFIN_UART_GCTL                 UART1_GCTL
 
+#define BFIN_UART_NR_PORTS     4
+
+#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
+#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
+#define OFFSET_GCTL             0x08   /* Global Control Register              */
+#define OFFSET_LCR              0x0C   /* Line Control Register                */
+#define OFFSET_MCR              0x10   /* Modem Control Register               */
+#define OFFSET_LSR              0x14   /* Line Status Register                 */
+#define OFFSET_MSR              0x18   /* Modem Status Register                */
+#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
+#define OFFSET_IER_SET          0x20   /* Set Interrupt Enable Register        */
+#define OFFSET_IER_CLEAR        0x24   /* Clear Interrupt Enable Register      */
+#define OFFSET_THR              0x28   /* Transmit Holding register            */
+#define OFFSET_RBR              0x2C   /* Receive Buffer register              */
+
 /* PLL_DIV Masks */
 #define CCLK_DIV1 CSEL_DIV1    /* CCLK = VCO / 1 */
 #define CCLK_DIV2 CSEL_DIV2    /* CCLK = VCO / 2 */

diff --git a/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h
index b6f513b..8a4e66d 100644 (file)
--- a/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h
+++ b/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h
@@ -1,22 +1,38 @@
+/*
+ * file:        include/asm-blackfin/mach-bf561/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ *     blackfin serial driver head file
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
 #include <linux/serial.h>
 #include <asm/dma.h>
 #include <asm/portmux.h>
 
-#define NR_PORTS                1
-
-#define OFFSET_THR              0x00   /* Transmit Holding register            */
-#define OFFSET_RBR              0x00   /* Receive Buffer register              */
-#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
-#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
-#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
-#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
-#define OFFSET_LCR              0x0C   /* Line Control Register                */
-#define OFFSET_MCR              0x10   /* Modem Control Register               */
-#define OFFSET_LSR              0x14   /* Line Status Register                 */
-#define OFFSET_MSR              0x18   /* Modem Status Register                */
-#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
-#define OFFSET_GCTL             0x24   /* Global Control Register              */
-
 #define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
 #define UART_GET_DLL(uart)     bfin_read16(((uart)->port.membase + OFFSET_DLL))
 #define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
@@ -84,7 +100,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
        bfin_write16(uart->port.membase + OFFSET_LSR, -1);
 }
 
-struct bfin_serial_port bfin_serial_ports[NR_PORTS];
+struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
 struct bfin_serial_res {
        unsigned long   uart_base_addr;
        int             uart_irq;
@@ -115,7 +131,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
 
 #define DRIVER_NAME "bfin-uart"
 
-int nr_ports = NR_PORTS;
+int nr_ports = BFIN_UART_NR_PORTS;
 static void bfin_serial_hw_init(struct bfin_serial_port *uart)
 {
 

diff --git a/include/asm-blackfin/mach-bf561/bfin_sir.h b/include/asm-blackfin/mach-bf561/bfin_sir.h
new file mode 100644 (file)
index 0000000..cefcf8b
--- /dev/null
+++ b/include/asm-blackfin/mach-bf561/bfin_sir.h
@@ -0,0 +1,120 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port)   bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port)    bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port)    bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_GET_DLH(port)    bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_IIR(port)    bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_LCR(port)    bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port)   bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v)  bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER), v)
+#define SIR_UART_PUT_DLH(port, v)  bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v)  bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+       char *buf;
+       int head;
+       int tail;
+       };
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+       unsigned char __iomem   *membase;
+       unsigned int            irq;
+       unsigned int            lsr;
+       unsigned long           clk;
+       struct net_device       *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+       int                     tx_done;
+       struct dma_rx_buf       rx_dma_buf;
+       struct timer_list       rx_dma_timer;
+       int                     rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+       unsigned int            tx_dma_channel;
+       unsigned int            rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+       unsigned long   base_addr;
+       int             irq;
+       unsigned int    rx_dma_channel;
+       unsigned int    tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+       {
+       0xFFC00400,
+       IRQ_UART_RX,
+       CH_UART_RX,
+       CH_UART_TX,
+       },
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+       struct bfin_sir_port    *sir_port;
+       spinlock_t              lock;
+       unsigned int            open;
+       int                     speed;
+       int                     newspeed;
+
+       struct sk_buff          *txskb;
+       struct sk_buff          *rxskb;
+       struct net_device_stats stats;
+       struct device           *dev;
+       struct irlap_cb         *irlap;
+       struct qos_info         qos;
+
+       iobuff_t                tx_buff;
+       iobuff_t                rx_buff;
+
+       struct work_struct      work;
+       int                     mtt;
+};
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+       unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+       port->lsr |= (lsr & (BI|FE|PE|OE));
+       return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+       port->lsr = 0;
+       bfin_read16(port->membase + OFFSET_LSR);
+}
+
+#define DRIVER_NAME "bfin_sir"
+
+static void bfin_sir_hw_init(void)
+{
+#ifdef CONFIG_BFIN_SIR0
+       peripheral_request(P_UART0_TX, DRIVER_NAME);
+       peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+       SSYNC();
+}

diff --git a/include/asm-blackfin/mach-bf561/blackfin.h b/include/asm-blackfin/mach-bf561/blackfin.h
index 3a16df2..0ea8666 100644 (file)
--- a/include/asm-blackfin/mach-bf561/blackfin.h
+++ b/include/asm-blackfin/mach-bf561/blackfin.h
@@ -69,5 +69,19 @@
 #define bfin_read_SIC_ISR(x)           bfin_read32(SICA_ISR0 + (x << 2))
 #define bfin_write_SIC_ISR(x, val)     bfin_write32((SICA_ISR0 + (x << 2)), val)
 
+#define BFIN_UART_NR_PORTS      1
+
+#define OFFSET_THR              0x00   /* Transmit Holding register            */
+#define OFFSET_RBR              0x00   /* Receive Buffer register              */
+#define OFFSET_DLL              0x00   /* Divisor Latch (Low-Byte)             */
+#define OFFSET_IER              0x04   /* Interrupt Enable Register            */
+#define OFFSET_DLH              0x04   /* Divisor Latch (High-Byte)            */
+#define OFFSET_IIR              0x08   /* Interrupt Identification Register    */
+#define OFFSET_LCR              0x0C   /* Line Control Register                */
+#define OFFSET_MCR              0x10   /* Modem Control Register               */
+#define OFFSET_LSR              0x14   /* Line Status Register                 */
+#define OFFSET_MSR              0x18   /* Modem Status Register                */
+#define OFFSET_SCR              0x1C   /* SCR Scratch Register                 */
+#define OFFSET_GCTL             0x24   /* Global Control Register              */
 
 #endif                         /* _MACH_BLACKFIN_H_ */