the client address and this parameter is NOT empty only
replies from the specified server are accepted.
- Only required for for NFS root. That is autoconfiguration
+ Only required for NFS root. That is autoconfiguration
will not be triggered if it is missing and NFS root is not
in operation.
devices. This field represents the number of cells needed to
represent the address of the memory-mapped registers of devices
within the system controller chip.
- - #size-cells : Size representation for for the memory-mapped
+ - #size-cells : Size representation for the memory-mapped
registers within the system controller chip.
- #interrupt-cells : Defines the width of cells used to represent
interrupts.
#define AMBEN_B0_B1 0x0004 /* Enable Asynchronous Memory Banks 0 & 1 only */
#define AMBEN_B0_B1_B2 0x0006 /* Enable Asynchronous Memory Banks 0, 1, and 2 */
#define AMBEN_ALL 0x0008 /* Enable Asynchronous Memory Banks (all) 0, 1, 2, and 3 */
-#define CDPRIO 0x0100 /* DMA has priority over core for for external accesses */
+#define CDPRIO 0x0100 /* DMA has priority over core for external accesses */
/* EBIU_AMGCTL Bit Positions */
#define AMCKEN_P 0x0000 /* Enable CLKOUT */
/*
- * udbg for for NS16550 compatable serial ports
+ * udbg for NS16550 compatable serial ports
*
* Copyright (C) 2001-2005 PPC 64 Team, IBM Corp
*
/*
- * udbg for for zilog scc ports as found on Apple PowerMacs
+ * udbg for zilog scc ports as found on Apple PowerMacs
*
* Copyright (C) 2001-2005 PPC 64 Team, IBM Corp
*
* is irrespective of the memory devices being mounted
* on both sides of the memory stick.
*
- * Socket set: All of the memory sticks that are required for for
+ * Socket set: All of the memory sticks that are required for
* a single memory access or all of the memory sticks
* spanned by a chip-select row. A single socket set
* has two chip-select rows and if double-sided sticks
* errors. We only bother to do this at load time, because it's OK if
* it happened before we were loaded (first time after boot/reset),
* but any time after that, it's fatal anyway. Also need to not check
- * for for upper byte errors if we are in 8 bit mode, so figure out
+ * for upper byte errors if we are in 8 bit mode, so figure out
* our width. For now, at least, also complain if it's 8 bit.
*/
static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev,
* Be aware that this is not an atomic operation when sleep != 0, even though
* interrupts are turned off! Well, like that we are currently only called
* on behalf of a read system call on raw device files (which are documented
- * to be dangerous and for for debugging purpose only). The inode semaphore
+ * to be dangerous and for debugging purpose only). The inode semaphore
* takes care that this is not called for the same minor device number while
* we are sleeping, but access is not serialized against simultaneous read()
* from the corresponding ttyI device. Can other ugly events, like changes
* Be aware that this is not an atomic operation when sleep != 0, even though
* interrupts are turned off! Well, like that we are currently only called
* on behalf of a read system call on raw device files (which are documented
- * to be dangerous and for for debugging purpose only). The inode semaphore
+ * to be dangerous and for debugging purpose only). The inode semaphore
* takes care that this is not called for the same minor device number while
* we are sleeping, but access is not serialized against simultaneous read()
* from the corresponding ttyI device. Can other ugly events, like changes
* INTR: resync needs to be aborted for some reason
* DONE: thread is done and is waiting to be reaped
* REQUEST: user-space has requested a sync (used with SYNC)
- * CHECK: user-space request for for check-only, no repair
+ * CHECK: user-space request for check-only, no repair
* RESHAPE: A reshape is happening
*
* If neither SYNC or RESHAPE are set, then it is a recovery.
The fields are:[4:0] - tail pointer; [10:5] - Link List size; 15:11] -
header pointer. */
#define TCM_REG_XX_TABLE 0x50240
-/* [RW 4] Load value for for cfc ac credit cnt. */
+/* [RW 4] Load value for cfc ac credit cnt. */
#define TM_REG_CFC_AC_CRDCNT_VAL 0x164208
/* [RW 4] Load value for cfc cld credit cnt. */
#define TM_REG_CFC_CLD_CRDCNT_VAL 0x164210
static int rionet_capable = 1;
/*
- * This is a fast lookup table for for translating TX
+ * This is a fast lookup table for translating TX
* Ethernet packets into a destination RIO device. It
* could be made into a hash table to save memory depending
* on system trade-offs.
* System suspend currently expects to be able to suspend the entire
* device tree, device-at-a-time. If we failed selective suspend
* reports, system suspend would fail; so the root hub code must claim
- * success. That's lying to usbcore, and it matters for for runtime
+ * success. That's lying to usbcore, and it matters for runtime
* PM scenarios with selective suspend and remote wakeup...
*/
if (ehci->no_selective_suspend && device_can_wakeup(&pdev->dev))
#define __hc16 __le16
#endif
-/* statistics can be kept for for tuning/monitoring */
+/* statistics can be kept for tuning/monitoring */
struct ehci_stats {
/* irq usage */
unsigned long normal;
#define BMV_IF_VALID \
(BMV_IF_ATTRFORK|BMV_IF_NO_DMAPI_READ|BMV_IF_PREALLOC|BMV_IF_DELALLOC)
-/* bmv_oflags values - returned for for each non-header segment */
+/* bmv_oflags values - returned for each non-header segment */
#define BMV_OF_PREALLOC 0x1 /* segment = unwritten pre-allocation */
#define BMV_OF_DELALLOC 0x2 /* segment = delayed allocation */
#define BMV_OF_LAST 0x4 /* segment is the last in the file */
* @start_frame: Returns the initial frame for isochronous transfers.
* @number_of_packets: Lists the number of ISO transfer buffers.
* @interval: Specifies the polling interval for interrupt or isochronous
- * transfers. The units are frames (milliseconds) for for full and low
+ * transfers. The units are frames (milliseconds) for full and low
* speed devices, and microframes (1/8 millisecond) for highspeed ones.
* @error_count: Returns the number of ISO transfers that reported errors.
* @context: For use in completion functions. This normally points to
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff