ARM: always select HAVE_IDE

It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h

It turns out this was done for ARM, and we can simply always select
HAVE_IDE on ARM instead of manually tracking which platforms might
possible have an IDE controller directly or indirectly.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index d8d2532..b786e68 100644 (file)
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -8,6 +8,7 @@ mainmenu "Linux Kernel Configuration"
 config ARM
        bool
        default y
+       select HAVE_IDE
        select RTC_LIB
        select SYS_SUPPORTS_APM_EMULATION
        select HAVE_OPROFILE
@@ -223,7 +224,6 @@ config ARCH_CLPS7500
        select TIMER_ACORN
        select ISA
        select NO_IOPORT
-       select HAVE_IDE
        help
          Support for the Cirrus Logic PS7500FE system-on-a-chip.
 
@@ -236,7 +236,6 @@ config ARCH_CO285
        bool "Co-EBSA285"
        select FOOTBRIDGE
        select FOOTBRIDGE_ADDIN
-       select HAVE_IDE
        help
          Support for Intel's EBSA285 companion chip.
 
@@ -262,7 +261,6 @@ config ARCH_EP93XX
 config ARCH_FOOTBRIDGE
        bool "FootBridge"
        select FOOTBRIDGE
-       select HAVE_IDE
        help
          Support for systems based on the DC21285 companion chip
          ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
@@ -301,7 +299,6 @@ config ARCH_IOP32X
        depends on MMU
        select PLAT_IOP
        select PCI
-       select HAVE_IDE
        help
          Support for Intel's 80219 and IOP32X (XScale) family of
          processors.
@@ -311,14 +308,12 @@ config ARCH_IOP33X
        depends on MMU
        select PLAT_IOP
        select PCI
-       select HAVE_IDE
        help
          Support for Intel's IOP33X (XScale) family of processors.
 
 config ARCH_IXP23XX
        bool "IXP23XX-based"
        depends on MMU
-       select HAVE_IDE
        select PCI
        help
          Support for Intel's IXP23xx (XScale) family of processors.
@@ -336,14 +331,12 @@ config ARCH_IXP4XX
        select GENERIC_GPIO
        select GENERIC_TIME
        select GENERIC_CLOCKEVENTS
-       select HAVE_IDE
        help
          Support for Intel's IXP4XX (XScale) family of processors.
 
 config ARCH_L7200
        bool "LinkUp-L7200"
        select FIQ
-       select HAVE_IDE
        help
          Say Y here if you intend to run this kernel on a LinkUp Systems
          L7200 Software Development Board which uses an ARM720T processor.
@@ -400,7 +393,6 @@ config ARCH_PXA
        depends on MMU
        select ARCH_MTD_XIP
        select GENERIC_GPIO
-       select HAVE_IDE
        select HAVE_GPIO_LIB
        select GENERIC_TIME
        select GENERIC_CLOCKEVENTS
@@ -416,7 +408,6 @@ config ARCH_RPC
        select ARCH_MAY_HAVE_PC_FDC
        select ISA_DMA_API
        select NO_IOPORT
-       select HAVE_IDE
        help
          On the Acorn Risc-PC, Linux can support the internal IDE disk and
          CD-ROM interface, serial and parallel port, and the floppy drive.
@@ -432,7 +423,6 @@ config ARCH_SA1100
        select GENERIC_TIME
        select GENERIC_CLOCKEVENTS
        select TICK_ONESHOT
-       select HAVE_IDE
        select HAVE_GPIO_LIB
        help
          Support for StrongARM 11x0 based boards.
@@ -440,7 +430,6 @@ config ARCH_SA1100
 config ARCH_S3C2410
        bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443"
        select GENERIC_GPIO
-       select HAVE_IDE
        help
          Samsung S3C2410X CPU based systems, such as the Simtec Electronics
          BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
@@ -448,7 +437,6 @@ config ARCH_S3C2410
 
 config ARCH_SHARK
        bool "Shark"
-       select HAVE_IDE
        select ISA
        select ISA_DMA
        select PCI
@@ -458,7 +446,6 @@ config ARCH_SHARK
 
 config ARCH_LH7A40X
        bool "Sharp LH7A40X"
-       select HAVE_IDE
        help
          Say Y here for systems based on one of the Sharp LH7A40X
          System on a Chip processors.  These CPUs include an ARM922T

diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index 8d88526..1b0eb5a 100644 (file)
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -38,7 +38,6 @@ config PCMCIA_DEBUG
 config PCMCIA
        tristate "16-bit PCMCIA support"
        select CRC32
-       select HAVE_IDE
        default y
        ---help---
           This option enables support for 16-bit PCMCIA cards. Most older