source "arch/arm/mach-omap1/Kconfig"
+source "arch/arm/mach-omap2/Kconfig"
+
source "arch/arm/mach-s3c2410/Kconfig"
source "arch/arm/mach-lh7a40x/Kconfig"
machine-$(CONFIG_ARCH_IXP4XX) := ixp4xx
machine-$(CONFIG_ARCH_IXP2000) := ixp2000
machine-$(CONFIG_ARCH_OMAP1) := omap1
+ machine-$(CONFIG_ARCH_OMAP2) := omap2
incdir-$(CONFIG_ARCH_OMAP) := omap
machine-$(CONFIG_ARCH_S3C2410) := s3c2410
machine-$(CONFIG_ARCH_LH7A40X) := lh7a40x
--- /dev/null
+comment "OMAP Core Type"
+ depends on ARCH_OMAP2
+
+config ARCH_OMAP24XX
+ bool "OMAP24xx Based System"
+ depends on ARCH_OMAP2
+
+config ARCH_OMAP2420
+ bool "OMAP2420 support"
+ depends on ARCH_OMAP24XX
+
+comment "OMAP Board Type"
+ depends on ARCH_OMAP2
+
+config MACH_OMAP_GENERIC
+ bool "Generic OMAP board"
+ depends on ARCH_OMAP2 && ARCH_OMAP24XX
+
+config MACH_OMAP_H4
+ bool "OMAP 2420 H4 board"
+ depends on ARCH_OMAP2 && ARCH_OMAP24XX
+
--- /dev/null
+#
+# Makefile for the linux kernel.
+#
+
+# Common support
+obj-y := irq.o id.o io.o sram-fn.o clock.o mux.o devices.o serial.o
+
+obj-$(CONFIG_OMAP_MPU_TIMER) += timer-gp.o
+
+# Specific board support
+obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
+obj-$(CONFIG_MACH_OMAP_H4) += board-h4.o
+
--- /dev/null
+ zreladdr-y := 0x80008000
+params_phys-y := 0x80000100
+initrd_phys-y := 0x80800000
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap/omap2/board-generic.c
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Paul Mundt <paul.mundt@nokia.com>
+ *
+ * Modified from mach-omap/omap1/board-generic.c
+ *
+ * Code for generic OMAP2 board. Should work on many OMAP2 systems where
+ * the bootloader passes the board-specific data to the kernel.
+ * Do not put any board specific code to this file; create a new machine
+ * type if you need custom low-level initializations.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <asm/arch/gpio.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/usb.h>
+#include <asm/arch/board.h>
+#include <asm/arch/common.h>
+
+static void __init omap_generic_init_irq(void)
+{
+ omap_init_irq();
+}
+
+static struct omap_uart_config generic_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_mmc_config generic_mmc_config __initdata = {
+ .mmc [0] = {
+ .enabled = 0,
+ .wire4 = 0,
+ .wp_pin = -1,
+ .power_pin = -1,
+ .switch_pin = -1,
+ },
+};
+
+static struct omap_board_config_kernel generic_config[] = {
+ { OMAP_TAG_UART, &generic_uart_config },
+ { OMAP_TAG_MMC, &generic_mmc_config },
+};
+
+static void __init omap_generic_init(void)
+{
+ omap_board_config = generic_config;
+ omap_board_config_size = ARRAY_SIZE(generic_config);
+ omap_serial_init();
+}
+
+static void __init omap_generic_map_io(void)
+{
+ omap_map_common_io();
+}
+
+MACHINE_START(OMAP_GENERIC, "Generic OMAP24xx")
+ /* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
+ .phys_ram = 0x80000000,
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = omap_generic_map_io,
+ .init_irq = omap_generic_init_irq,
+ .init_machine = omap_generic_init,
+ .timer = &omap_timer,
+MACHINE_END
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap/omap2/board-h4.c
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Paul Mundt <paul.mundt@nokia.com>
+ *
+ * Modified from mach-omap/omap1/board-generic.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/delay.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <asm/arch/gpio.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/usb.h>
+#include <asm/arch/board.h>
+#include <asm/arch/common.h>
+#include <asm/arch/prcm.h>
+
+#include <asm/io.h>
+#include <asm/delay.h>
+
+static struct mtd_partition h4_partitions[] = {
+ /* bootloader (U-Boot, etc) in first sector */
+ {
+ .name = "bootloader",
+ .offset = 0,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ /* bootloader params in the next sector */
+ {
+ .name = "params",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_128K,
+ .mask_flags = 0,
+ },
+ /* kernel */
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_2M,
+ .mask_flags = 0
+ },
+ /* file system */
+ {
+ .name = "filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0
+ }
+};
+
+static struct flash_platform_data h4_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+ .parts = h4_partitions,
+ .nr_parts = ARRAY_SIZE(h4_partitions),
+};
+
+static struct resource h4_flash_resource = {
+ .start = H4_CS0_BASE,
+ .end = H4_CS0_BASE + SZ_64M - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device h4_flash_device = {
+ .name = "omapflash",
+ .id = 0,
+ .dev = {
+ .platform_data = &h4_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &h4_flash_resource,
+};
+
+static struct resource h4_smc91x_resources[] = {
+ [0] = {
+ .start = OMAP24XX_ETHR_START, /* Physical */
+ .end = OMAP24XX_ETHR_START + 0xf,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
+ .end = OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device h4_smc91x_device = {
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(h4_smc91x_resources),
+ .resource = h4_smc91x_resources,
+};
+
+static struct platform_device *h4_devices[] __initdata = {
+ &h4_smc91x_device,
+ &h4_flash_device,
+};
+
+static inline void __init h4_init_smc91x(void)
+{
+ /* Make sure CS1 timings are correct */
+ GPMC_CONFIG1_1 = 0x00011200;
+ GPMC_CONFIG2_1 = 0x001f1f01;
+ GPMC_CONFIG3_1 = 0x00080803;
+ GPMC_CONFIG4_1 = 0x1c091c09;
+ GPMC_CONFIG5_1 = 0x041f1f1f;
+ GPMC_CONFIG6_1 = 0x000004c4;
+ GPMC_CONFIG7_1 = 0x00000f40 | (0x08000000 >> 24);
+ udelay(100);
+
+ omap_cfg_reg(M15_24XX_GPIO92);
+ if (omap_request_gpio(OMAP24XX_ETHR_GPIO_IRQ) < 0) {
+ printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
+ OMAP24XX_ETHR_GPIO_IRQ);
+ return;
+ }
+ omap_set_gpio_direction(OMAP24XX_ETHR_GPIO_IRQ, 1);
+}
+
+static void __init omap_h4_init_irq(void)
+{
+ omap_init_irq();
+ omap_gpio_init();
+ h4_init_smc91x();
+}
+
+static struct omap_uart_config h4_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_mmc_config h4_mmc_config __initdata = {
+ .mmc [0] = {
+ .enabled = 1,
+ .wire4 = 1,
+ .wp_pin = -1,
+ .power_pin = -1,
+ .switch_pin = -1,
+ },
+};
+
+static struct omap_lcd_config h4_lcd_config __initdata = {
+ .panel_name = "h4",
+ .ctrl_name = "internal",
+};
+
+static struct omap_board_config_kernel h4_config[] = {
+ { OMAP_TAG_UART, &h4_uart_config },
+ { OMAP_TAG_MMC, &h4_mmc_config },
+ { OMAP_TAG_LCD, &h4_lcd_config },
+};
+
+static void __init omap_h4_init(void)
+{
+ /*
+ * Make sure the serial ports are muxed on at this point.
+ * You have to mux them off in device drivers later on
+ * if not needed.
+ */
+ platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
+ omap_board_config = h4_config;
+ omap_board_config_size = ARRAY_SIZE(h4_config);
+ omap_serial_init();
+}
+
+static void __init omap_h4_map_io(void)
+{
+ omap_map_common_io();
+}
+
+MACHINE_START(OMAP_H4, "OMAP2420 H4 board")
+ /* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
+ .phys_ram = 0x80000000,
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = omap_h4_map_io,
+ .init_irq = omap_h4_init_irq,
+ .init_machine = omap_h4_init,
+ .timer = &omap_timer,
+MACHINE_END
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap2/devices.c
+ *
+ * OMAP2 platform device setup/initialization
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/mach-types.h>
+#include <asm/mach/map.h>
+
+#include <asm/arch/tc.h>
+#include <asm/arch/board.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/gpio.h>
+
+extern void omap_nop_release(struct device *dev);
+
+/*-------------------------------------------------------------------------*/
+
+#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE)
+
+#define OMAP2_I2C_BASE2 0x48072000
+#define OMAP2_I2C_INT2 57
+
+static struct resource i2c_resources2[] = {
+ {
+ .start = OMAP2_I2C_BASE2,
+ .end = OMAP2_I2C_BASE2 + 0x3f,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP2_I2C_INT2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device omap_i2c_device2 = {
+ .name = "i2c_omap",
+ .id = 2,
+ .dev = {
+ .release = omap_nop_release,
+ },
+ .num_resources = ARRAY_SIZE(i2c_resources2),
+ .resource = i2c_resources2,
+};
+
+/* See also arch/arm/plat-omap/devices.c for first I2C on 24xx */
+static void omap_init_i2c(void)
+{
+ /* REVISIT: Second I2C not in use on H4? */
+ if (machine_is_omap_h4())
+ return;
+
+ omap_cfg_reg(J15_24XX_I2C2_SCL);
+ omap_cfg_reg(H19_24XX_I2C2_SDA);
+ (void) platform_device_register(&omap_i2c_device2);
+}
+
+#else
+
+static void omap_init_i2c(void) {}
+
+#endif
+
+/*-------------------------------------------------------------------------*/
+
+static int __init omap2_init_devices(void)
+{
+ /* please keep these calls, and their implementations above,
+ * in alphabetical order so they're easier to sort through.
+ */
+ omap_init_i2c();
+
+ return 0;
+}
+arch_initcall(omap2_init_devices);
+
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap2/id.c
+ *
+ * OMAP2 CPU identification code
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Written by Tony Lindgren <tony@atomide.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+#define OMAP24XX_TAP_BASE io_p2v(0x48014000)
+
+#define OMAP_TAP_IDCODE 0x0204
+#define OMAP_TAP_PROD_ID 0x0208
+
+#define OMAP_TAP_DIE_ID_0 0x0218
+#define OMAP_TAP_DIE_ID_1 0x021C
+#define OMAP_TAP_DIE_ID_2 0x0220
+#define OMAP_TAP_DIE_ID_3 0x0224
+
+/* system_rev fields for OMAP2 processors:
+ * CPU id bits [31:16],
+ * CPU device type [15:12], (unprg,normal,POP)
+ * CPU revision [11:08]
+ * CPU class bits [07:00]
+ */
+
+struct omap_id {
+ u16 hawkeye; /* Silicon type (Hawkeye id) */
+ u8 dev; /* Device type from production_id reg */
+ u32 type; /* combined type id copied to system_rev */
+};
+
+/* Register values to detect the OMAP version */
+static struct omap_id omap_ids[] __initdata = {
+ { .hawkeye = 0xb5d9, .dev = 0x0, .type = 0x24200000 },
+ { .hawkeye = 0xb5d9, .dev = 0x1, .type = 0x24201000 },
+ { .hawkeye = 0xb5d9, .dev = 0x2, .type = 0x24202000 },
+ { .hawkeye = 0xb5d9, .dev = 0x4, .type = 0x24220000 },
+ { .hawkeye = 0xb5d9, .dev = 0x8, .type = 0x24230000 },
+ { .hawkeye = 0xb68a, .dev = 0x0, .type = 0x24300000 },
+};
+
+static u32 __init read_tap_reg(int reg)
+{
+ return __raw_readl(OMAP24XX_TAP_BASE + reg);
+}
+
+void __init omap2_check_revision(void)
+{
+ int i, j;
+ u32 idcode;
+ u32 prod_id;
+ u16 hawkeye;
+ u8 dev_type;
+ u8 rev;
+
+ idcode = read_tap_reg(OMAP_TAP_IDCODE);
+ prod_id = read_tap_reg(OMAP_TAP_PROD_ID);
+ hawkeye = (idcode >> 12) & 0xffff;
+ rev = (idcode >> 28) & 0x0f;
+ dev_type = (prod_id >> 16) & 0x0f;
+
+#ifdef DEBUG
+ printk(KERN_DEBUG "OMAP_TAP_IDCODE 0x%08x REV %i HAWKEYE 0x%04x MANF %03x\n",
+ idcode, rev, hawkeye, (idcode >> 1) & 0x7ff);
+ printk(KERN_DEBUG "OMAP_TAP_DIE_ID_0: 0x%08x\n",
+ read_tap_reg(OMAP_TAP_DIE_ID_0));
+ printk(KERN_DEBUG "OMAP_TAP_DIE_ID_1: 0x%08x DEV_REV: %i\n",
+ read_tap_reg(OMAP_TAP_DIE_ID_1),
+ (read_tap_reg(OMAP_TAP_DIE_ID_1) >> 28) & 0xf);
+ printk(KERN_DEBUG "OMAP_TAP_DIE_ID_2: 0x%08x\n",
+ read_tap_reg(OMAP_TAP_DIE_ID_2));
+ printk(KERN_DEBUG "OMAP_TAP_DIE_ID_3: 0x%08x\n",
+ read_tap_reg(OMAP_TAP_DIE_ID_3));
+ printk(KERN_DEBUG "OMAP_TAP_PROD_ID_0: 0x%08x DEV_TYPE: %i\n",
+ prod_id, dev_type);
+#endif
+
+ /* Check hawkeye ids */
+ for (i = 0; i < ARRAY_SIZE(omap_ids); i++) {
+ if (hawkeye == omap_ids[i].hawkeye)
+ break;
+ }
+
+ if (i == ARRAY_SIZE(omap_ids)) {
+ printk(KERN_ERR "Unknown OMAP CPU id\n");
+ return;
+ }
+
+ for (j = i; j < ARRAY_SIZE(omap_ids); j++) {
+ if (dev_type == omap_ids[j].dev)
+ break;
+ }
+
+ if (j == ARRAY_SIZE(omap_ids)) {
+ printk(KERN_ERR "Unknown OMAP device type. "
+ "Handling it as OMAP%04x\n",
+ omap_ids[i].type >> 16);
+ j = i;
+ }
+ system_rev = omap_ids[j].type;
+
+ system_rev |= rev << 8;
+
+ /* Add the cpu class info (24xx) */
+ system_rev |= 0x24;
+
+ pr_info("OMAP%04x", system_rev >> 16);
+ if ((system_rev >> 8) & 0x0f)
+ printk("%x", (system_rev >> 8) & 0x0f);
+ printk("\n");
+}
+
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap2/io.c
+ *
+ * OMAP2 I/O mapping code
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Juha Yrjölä <juha.yrjola@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/mach/map.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+
+extern void omap_sram_init(void);
+extern int omap2_clk_init(void);
+extern void omap2_check_revision(void);
+
+/*
+ * The machine specific code may provide the extra mapping besides the
+ * default mapping provided here.
+ */
+static struct map_desc omap2_io_desc[] __initdata = {
+ {
+ .virtual = L3_24XX_VIRT,
+ .pfn = __phys_to_pfn(L3_24XX_PHYS),
+ .length = L3_24XX_SIZE,
+ .type = MT_DEVICE
+ },
+ {
+ .virtual = L4_24XX_VIRT,
+ .pfn = __phys_to_pfn(L4_24XX_PHYS),
+ .length = L4_24XX_SIZE,
+ .type = MT_DEVICE
+ }
+};
+
+void __init omap_map_common_io(void)
+{
+ iotable_init(omap2_io_desc, ARRAY_SIZE(omap2_io_desc));
+ omap2_check_revision();
+ omap_sram_init();
+ omap2_mux_init();
+ omap2_clk_init();
+}
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap/omap2/irq.c
+ *
+ * Interrupt handler for OMAP2 boards.
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Paul Mundt <paul.mundt@nokia.com>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/config.h>
+#include <linux/interrupt.h>
+#include <asm/hardware.h>
+#include <asm/mach/irq.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#define INTC_REVISION 0x0000
+#define INTC_SYSCONFIG 0x0010
+#define INTC_SYSSTATUS 0x0014
+#define INTC_CONTROL 0x0048
+#define INTC_MIR_CLEAR0 0x0088
+#define INTC_MIR_SET0 0x008c
+
+/*
+ * OMAP2 has a number of different interrupt controllers, each interrupt
+ * controller is identified as its own "bank". Register definitions are
+ * fairly consistent for each bank, but not all registers are implemented
+ * for each bank.. when in doubt, consult the TRM.
+ */
+static struct omap_irq_bank {
+ unsigned long base_reg;
+ unsigned int nr_irqs;
+} __attribute__ ((aligned(4))) irq_banks[] = {
+ {
+ /* MPU INTC */
+ .base_reg = OMAP24XX_IC_BASE,
+ .nr_irqs = 96,
+ }, {
+ /* XXX: DSP INTC */
+
+#if 0
+ /*
+ * Commented out for now until we fix the IVA clocking
+ */
+#ifdef CONFIG_ARCH_OMAP2420
+ }, {
+ /* IVA INTC (2420 only) */
+ .base_reg = OMAP24XX_IVA_INTC_BASE,
+ .nr_irqs = 16, /* Actually 32, but only 16 are used */
+#endif
+#endif
+ }
+};
+
+/* XXX: FIQ and additional INTC support (only MPU at the moment) */
+static void omap_ack_irq(unsigned int irq)
+{
+ omap_writel(0x1, irq_banks[0].base_reg + INTC_CONTROL);
+}
+
+static void omap_mask_irq(unsigned int irq)
+{
+ int offset = (irq >> 5) << 5;
+
+ if (irq >= 64) {
+ irq %= 64;
+ } else if (irq >= 32) {
+ irq %= 32;
+ }
+
+ omap_writel(1 << irq, irq_banks[0].base_reg + INTC_MIR_SET0 + offset);
+}
+
+static void omap_unmask_irq(unsigned int irq)
+{
+ int offset = (irq >> 5) << 5;
+
+ if (irq >= 64) {
+ irq %= 64;
+ } else if (irq >= 32) {
+ irq %= 32;
+ }
+
+ omap_writel(1 << irq, irq_banks[0].base_reg + INTC_MIR_CLEAR0 + offset);
+}
+
+static void omap_mask_ack_irq(unsigned int irq)
+{
+ omap_mask_irq(irq);
+ omap_ack_irq(irq);
+}
+
+static struct irqchip omap_irq_chip = {
+ .ack = omap_mask_ack_irq,
+ .mask = omap_mask_irq,
+ .unmask = omap_unmask_irq,
+};
+
+static void __init omap_irq_bank_init_one(struct omap_irq_bank *bank)
+{
+ unsigned long tmp;
+
+ tmp = omap_readl(bank->base_reg + INTC_REVISION) & 0xff;
+ printk(KERN_INFO "IRQ: Found an INTC at 0x%08lx "
+ "(revision %ld.%ld) with %d interrupts\n",
+ bank->base_reg, tmp >> 4, tmp & 0xf, bank->nr_irqs);
+
+ tmp = omap_readl(bank->base_reg + INTC_SYSCONFIG);
+ tmp |= 1 << 1; /* soft reset */
+ omap_writel(tmp, bank->base_reg + INTC_SYSCONFIG);
+
+ while (!(omap_readl(bank->base_reg + INTC_SYSSTATUS) & 0x1))
+ /* Wait for reset to complete */;
+}
+
+void __init omap_init_irq(void)
+{
+ unsigned long nr_irqs = 0;
+ unsigned int nr_banks = 0;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(irq_banks); i++) {
+ struct omap_irq_bank *bank = irq_banks + i;
+
+ /* XXX */
+ if (!bank->base_reg)
+ continue;
+
+ omap_irq_bank_init_one(bank);
+
+ nr_irqs += bank->nr_irqs;
+ nr_banks++;
+ }
+
+ printk(KERN_INFO "Total of %ld interrupts on %d active controller%s\n",
+ nr_irqs, nr_banks, nr_banks > 1 ? "s" : "");
+
+ for (i = 0; i < nr_irqs; i++) {
+ set_irq_chip(i, &omap_irq_chip);
+ set_irq_handler(i, do_level_IRQ);
+ set_irq_flags(i, IRQF_VALID);
+ }
+}
+
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap2/mux.c
+ *
+ * OMAP1 pin multiplexing configurations
+ *
+ * Copyright (C) 2003 - 2005 Nokia Corporation
+ *
+ * Written by Tony Lindgren <tony.lindgren@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <asm/system.h>
+#include <asm/io.h>
+#include <linux/spinlock.h>
+
+#include <asm/arch/mux.h>
+
+#ifdef CONFIG_OMAP_MUX
+
+/* NOTE: See mux.h for the enumeration */
+
+struct pin_config __initdata_or_module omap24xx_pins[] = {
+/*
+ * description mux mux pull pull debug
+ * offset mode ena type
+ */
+
+/* 24xx I2C */
+MUX_CFG_24XX("M19_24XX_I2C1_SCL", 0x111, 0, 0, 0, 1)
+MUX_CFG_24XX("L15_24XX_I2C1_SDA", 0x112, 0, 0, 0, 1)
+MUX_CFG_24XX("J15_24XX_I2C2_SCL", 0x113, 0, 0, 0, 1)
+MUX_CFG_24XX("H19_24XX_I2C2_SDA", 0x114, 0, 0, 0, 1)
+
+/* Menelaus interrupt */
+MUX_CFG_24XX("W19_24XX_SYS_NIRQ", 0x12c, 0, 1, 1, 1)
+
+/* 24xx GPIO */
+MUX_CFG_24XX("Y20_24XX_GPIO60", 0x12c, 3, 0, 0, 1)
+MUX_CFG_24XX("M15_24XX_GPIO92", 0x10a, 3, 0, 0, 1)
+
+};
+
+int __init omap2_mux_init(void)
+{
+ omap_mux_register(omap24xx_pins, ARRAY_SIZE(omap24xx_pins));
+ return 0;
+}
+
+#endif
--- /dev/null
+/*
+ * prcm.h - Access definations for use in OMAP24XX clock and power management
+ *
+ * Copyright (C) 2005 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __ASM_ARM_ARCH_DPM_PRCM_H
+#define __ASM_ARM_ARCH_DPM_PRCM_H
+
+/* SET_PERFORMANCE_LEVEL PARAMETERS */
+#define PRCM_HALF_SPEED 1
+#define PRCM_FULL_SPEED 2
+
+#ifndef __ASSEMBLER__
+
+#define PRCM_REG32(offset) __REG32(OMAP24XX_PRCM_BASE + (offset))
+
+#define PRCM_REVISION PRCM_REG32(0x000)
+#define PRCM_SYSCONFIG PRCM_REG32(0x010)
+#define PRCM_IRQSTATUS_MPU PRCM_REG32(0x018)
+#define PRCM_IRQENABLE_MPU PRCM_REG32(0x01C)
+#define PRCM_VOLTCTRL PRCM_REG32(0x050)
+#define PRCM_VOLTST PRCM_REG32(0x054)
+#define PRCM_CLKSRC_CTRL PRCM_REG32(0x060)
+#define PRCM_CLKOUT_CTRL PRCM_REG32(0x070)
+#define PRCM_CLKEMUL_CTRL PRCM_REG32(0x078)
+#define PRCM_CLKCFG_CTRL PRCM_REG32(0x080)
+#define PRCM_CLKCFG_STATUS PRCM_REG32(0x084)
+#define PRCM_VOLTSETUP PRCM_REG32(0x090)
+#define PRCM_CLKSSETUP PRCM_REG32(0x094)
+#define PRCM_POLCTRL PRCM_REG32(0x098)
+
+/* GENERAL PURPOSE */
+#define GENERAL_PURPOSE1 PRCM_REG32(0x0B0)
+#define GENERAL_PURPOSE2 PRCM_REG32(0x0B4)
+#define GENERAL_PURPOSE3 PRCM_REG32(0x0B8)
+#define GENERAL_PURPOSE4 PRCM_REG32(0x0BC)
+#define GENERAL_PURPOSE5 PRCM_REG32(0x0C0)
+#define GENERAL_PURPOSE6 PRCM_REG32(0x0C4)
+#define GENERAL_PURPOSE7 PRCM_REG32(0x0C8)
+#define GENERAL_PURPOSE8 PRCM_REG32(0x0CC)
+#define GENERAL_PURPOSE9 PRCM_REG32(0x0D0)
+#define GENERAL_PURPOSE10 PRCM_REG32(0x0D4)
+#define GENERAL_PURPOSE11 PRCM_REG32(0x0D8)
+#define GENERAL_PURPOSE12 PRCM_REG32(0x0DC)
+#define GENERAL_PURPOSE13 PRCM_REG32(0x0E0)
+#define GENERAL_PURPOSE14 PRCM_REG32(0x0E4)
+#define GENERAL_PURPOSE15 PRCM_REG32(0x0E8)
+#define GENERAL_PURPOSE16 PRCM_REG32(0x0EC)
+#define GENERAL_PURPOSE17 PRCM_REG32(0x0F0)
+#define GENERAL_PURPOSE18 PRCM_REG32(0x0F4)
+#define GENERAL_PURPOSE19 PRCM_REG32(0x0F8)
+#define GENERAL_PURPOSE20 PRCM_REG32(0x0FC)
+
+/* MPU */
+#define CM_CLKSEL_MPU PRCM_REG32(0x140)
+#define CM_CLKSTCTRL_MPU PRCM_REG32(0x148)
+#define RM_RSTST_MPU PRCM_REG32(0x158)
+#define PM_WKDEP_MPU PRCM_REG32(0x1C8)
+#define PM_EVGENCTRL_MPU PRCM_REG32(0x1D4)
+#define PM_EVEGENONTIM_MPU PRCM_REG32(0x1D8)
+#define PM_EVEGENOFFTIM_MPU PRCM_REG32(0x1DC)
+#define PM_PWSTCTRL_MPU PRCM_REG32(0x1E0)
+#define PM_PWSTST_MPU PRCM_REG32(0x1E4)
+
+/* CORE */
+#define CM_FCLKEN1_CORE PRCM_REG32(0x200)
+#define CM_FCLKEN2_CORE PRCM_REG32(0x204)
+#define CM_FCLKEN3_CORE PRCM_REG32(0x208)
+#define CM_ICLKEN1_CORE PRCM_REG32(0x210)
+#define CM_ICLKEN2_CORE PRCM_REG32(0x214)
+#define CM_ICLKEN3_CORE PRCM_REG32(0x218)
+#define CM_ICLKEN4_CORE PRCM_REG32(0x21C)
+#define CM_IDLEST1_CORE PRCM_REG32(0x220)
+#define CM_IDLEST2_CORE PRCM_REG32(0x224)
+#define CM_IDLEST3_CORE PRCM_REG32(0x228)
+#define CM_IDLEST4_CORE PRCM_REG32(0x22C)
+#define CM_AUTOIDLE1_CORE PRCM_REG32(0x230)
+#define CM_AUTOIDLE2_CORE PRCM_REG32(0x234)
+#define CM_AUTOIDLE3_CORE PRCM_REG32(0x238)
+#define CM_AUTOIDLE4_CORE PRCM_REG32(0x23C)
+#define CM_CLKSEL1_CORE PRCM_REG32(0x240)
+#define CM_CLKSEL2_CORE PRCM_REG32(0x244)
+#define CM_CLKSTCTRL_CORE PRCM_REG32(0x248)
+#define PM_WKEN1_CORE PRCM_REG32(0x2A0)
+#define PM_WKEN2_CORE PRCM_REG32(0x2A4)
+#define PM_WKST1_CORE PRCM_REG32(0x2B0)
+#define PM_WKST2_CORE PRCM_REG32(0x2B4)
+#define PM_WKDEP_CORE PRCM_REG32(0x2C8)
+#define PM_PWSTCTRL_CORE PRCM_REG32(0x2E0)
+#define PM_PWSTST_CORE PRCM_REG32(0x2E4)
+
+/* GFX */
+#define CM_FCLKEN_GFX PRCM_REG32(0x300)
+#define CM_ICLKEN_GFX PRCM_REG32(0x310)
+#define CM_IDLEST_GFX PRCM_REG32(0x320)
+#define CM_CLKSEL_GFX PRCM_REG32(0x340)
+#define CM_CLKSTCTRL_GFX PRCM_REG32(0x348)
+#define RM_RSTCTRL_GFX PRCM_REG32(0x350)
+#define RM_RSTST_GFX PRCM_REG32(0x358)
+#define PM_WKDEP_GFX PRCM_REG32(0x3C8)
+#define PM_PWSTCTRL_GFX PRCM_REG32(0x3E0)
+#define PM_PWSTST_GFX PRCM_REG32(0x3E4)
+
+/* WAKE-UP */
+#define CM_FCLKEN_WKUP PRCM_REG32(0x400)
+#define CM_ICLKEN_WKUP PRCM_REG32(0x410)
+#define CM_IDLEST_WKUP PRCM_REG32(0x420)
+#define CM_AUTOIDLE_WKUP PRCM_REG32(0x430)
+#define CM_CLKSEL_WKUP PRCM_REG32(0x440)
+#define RM_RSTCTRL_WKUP PRCM_REG32(0x450)
+#define RM_RSTTIME_WKUP PRCM_REG32(0x454)
+#define RM_RSTST_WKUP PRCM_REG32(0x458)
+#define PM_WKEN_WKUP PRCM_REG32(0x4A0)
+#define PM_WKST_WKUP PRCM_REG32(0x4B0)
+
+/* CLOCKS */
+#define CM_CLKEN_PLL PRCM_REG32(0x500)
+#define CM_IDLEST_CKGEN PRCM_REG32(0x520)
+#define CM_AUTOIDLE_PLL PRCM_REG32(0x530)
+#define CM_CLKSEL1_PLL PRCM_REG32(0x540)
+#define CM_CLKSEL2_PLL PRCM_REG32(0x544)
+
+/* DSP */
+#define CM_FCLKEN_DSP PRCM_REG32(0x800)
+#define CM_ICLKEN_DSP PRCM_REG32(0x810)
+#define CM_IDLEST_DSP PRCM_REG32(0x820)
+#define CM_AUTOIDLE_DSP PRCM_REG32(0x830)
+#define CM_CLKSEL_DSP PRCM_REG32(0x840)
+#define CM_CLKSTCTRL_DSP PRCM_REG32(0x848)
+#define RM_RSTCTRL_DSP PRCM_REG32(0x850)
+#define RM_RSTST_DSP PRCM_REG32(0x858)
+#define PM_WKEN_DSP PRCM_REG32(0x8A0)
+#define PM_WKDEP_DSP PRCM_REG32(0x8C8)
+#define PM_PWSTCTRL_DSP PRCM_REG32(0x8E0)
+#define PM_PWSTST_DSP PRCM_REG32(0x8E4)
+#define PRCM_IRQSTATUS_DSP PRCM_REG32(0x8F0)
+#define PRCM_IRQENABLE_DSP PRCM_REG32(0x8F4)
+
+/* IVA */
+#define PRCM_IRQSTATUS_IVA PRCM_REG32(0x8F8)
+#define PRCM_IRQENABLE_IVA PRCM_REG32(0x8FC)
+
+/* Modem on 2430 */
+#define CM_FCLKEN_MDM PRCM_REG32(0xC00)
+#define CM_ICLKEN_MDM PRCM_REG32(0xC10)
+#define CM_IDLEST_MDM PRCM_REG32(0xC20)
+#define CM_CLKSEL_MDM PRCM_REG32(0xC40)
+
+/* FIXME: Move to header for 2430 */
+#define DISP_BASE (OMAP24XX_L4_IO_BASE+0x50000)
+#define DISP_REG32(offset) __REG32(DISP_BASE + (offset))
+
+#define GPMC_BASE (OMAP24XX_GPMC_BASE)
+#define GPMC_REG32(offset) __REG32(GPMC_BASE + (offset))
+
+#define GPT1_BASE (OMAP24XX_GPT1)
+#define GPT1_REG32(offset) __REG32(GPT1_BASE + (offset))
+
+/* Misc sysconfig */
+#define DISPC_SYSCONFIG DISP_REG32(0x410)
+#define SPI_BASE (OMAP24XX_L4_IO_BASE+0x98000)
+#define MCSPI1_SYSCONFIG __REG32(SPI_BASE + 0x10)
+#define MCSPI2_SYSCONFIG __REG32(SPI_BASE+0x2000 + 0x10)
+
+//#define DSP_MMU_SYSCONFIG 0x5A000010
+#define CAMERA_MMU_SYSCONFIG __REG32(DISP_BASE+0x2C10)
+//#define IVA_MMU_SYSCONFIG 0x5D000010
+//#define DSP_DMA_SYSCONFIG 0x00FCC02C
+#define CAMERA_DMA_SYSCONFIG __REG32(DISP_BASE+0x282C)
+#define SYSTEM_DMA_SYSCONFIG __REG32(DISP_BASE+0x602C)
+#define GPMC_SYSCONFIG GPMC_REG32(0x010)
+#define MAILBOXES_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x94010)
+#define UART1_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x6A054)
+#define UART2_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x6C054)
+#define UART3_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x6E054)
+//#define IVA_SYSCONFIG 0x5C060010
+#define SDRC_SYSCONFIG __REG32(OMAP24XX_SDRC_BASE+0x10)
+#define SMS_SYSCONFIG __REG32(OMAP24XX_SMS_BASE+0x10)
+#define SSI_SYSCONFIG __REG32(DISP_BASE+0x8010)
+//#define VLYNQ_SYSCONFIG 0x67FFFE10
+
+/* rkw - good cannidates for PM_ to start what nm was trying */
+#define OMAP24XX_GPT2 (OMAP24XX_L4_IO_BASE+0x2A000)
+#define OMAP24XX_GPT3 (OMAP24XX_L4_IO_BASE+0x78000)
+#define OMAP24XX_GPT4 (OMAP24XX_L4_IO_BASE+0x7A000)
+#define OMAP24XX_GPT5 (OMAP24XX_L4_IO_BASE+0x7C000)
+#define OMAP24XX_GPT6 (OMAP24XX_L4_IO_BASE+0x7E000)
+#define OMAP24XX_GPT7 (OMAP24XX_L4_IO_BASE+0x80000)
+#define OMAP24XX_GPT8 (OMAP24XX_L4_IO_BASE+0x82000)
+#define OMAP24XX_GPT9 (OMAP24XX_L4_IO_BASE+0x84000)
+#define OMAP24XX_GPT10 (OMAP24XX_L4_IO_BASE+0x86000)
+#define OMAP24XX_GPT11 (OMAP24XX_L4_IO_BASE+0x88000)
+#define OMAP24XX_GPT12 (OMAP24XX_L4_IO_BASE+0x8A000)
+
+#define GPTIMER1_SYSCONFIG GPT1_REG32(0x010)
+#define GPTIMER2_SYSCONFIG __REG32(OMAP24XX_GPT2 + 0x10)
+#define GPTIMER3_SYSCONFIG __REG32(OMAP24XX_GPT3 + 0x10)
+#define GPTIMER4_SYSCONFIG __REG32(OMAP24XX_GPT4 + 0x10)
+#define GPTIMER5_SYSCONFIG __REG32(OMAP24XX_GPT5 + 0x10)
+#define GPTIMER6_SYSCONFIG __REG32(OMAP24XX_GPT6 + 0x10)
+#define GPTIMER7_SYSCONFIG __REG32(OMAP24XX_GPT7 + 0x10)
+#define GPTIMER8_SYSCONFIG __REG32(OMAP24XX_GPT8 + 0x10)
+#define GPTIMER9_SYSCONFIG __REG32(OMAP24XX_GPT9 + 0x10)
+#define GPTIMER10_SYSCONFIG __REG32(OMAP24XX_GPT10 + 0x10)
+#define GPTIMER11_SYSCONFIG __REG32(OMAP24XX_GPT11 + 0x10)
+#define GPTIMER12_SYSCONFIG __REG32(OMAP24XX_GPT12 + 0x10)
+
+#define GPIOX_BASE(X) (OMAP24XX_GPIO_BASE+(0x2000*((X)-1)))
+
+#define GPIO1_SYSCONFIG __REG32((GPIOX_BASE(1)+0x10))
+#define GPIO2_SYSCONFIG __REG32((GPIOX_BASE(2)+0x10))
+#define GPIO3_SYSCONFIG __REG32((GPIOX_BASE(3)+0x10))
+#define GPIO4_SYSCONFIG __REG32((GPIOX_BASE(4)+0x10))
+
+/* GP TIMER 1 */
+#define GPTIMER1_TISTAT GPT1_REG32(0x014)
+#define GPTIMER1_TISR GPT1_REG32(0x018)
+#define GPTIMER1_TIER GPT1_REG32(0x01C)
+#define GPTIMER1_TWER GPT1_REG32(0x020)
+#define GPTIMER1_TCLR GPT1_REG32(0x024)
+#define GPTIMER1_TCRR GPT1_REG32(0x028)
+#define GPTIMER1_TLDR GPT1_REG32(0x02C)
+#define GPTIMER1_TTGR GPT1_REG32(0x030)
+#define GPTIMER1_TWPS GPT1_REG32(0x034)
+#define GPTIMER1_TMAR GPT1_REG32(0x038)
+#define GPTIMER1_TCAR1 GPT1_REG32(0x03C)
+#define GPTIMER1_TSICR GPT1_REG32(0x040)
+#define GPTIMER1_TCAR2 GPT1_REG32(0x044)
+
+/* rkw -- base fix up please... */
+#define GPTIMER3_TISR __REG32(OMAP24XX_L4_IO_BASE+0x78018)
+
+/* SDRC */
+#define SDRC_DLLA_CTRL __REG32(OMAP24XX_SDRC_BASE+0x060)
+#define SDRC_DLLA_STATUS __REG32(OMAP24XX_SDRC_BASE+0x064)
+#define SDRC_DLLB_CTRL __REG32(OMAP24XX_SDRC_BASE+0x068)
+#define SDRC_DLLB_STATUS __REG32(OMAP24XX_SDRC_BASE+0x06C)
+#define SDRC_POWER __REG32(OMAP24XX_SDRC_BASE+0x070)
+#define SDRC_MR_0 __REG32(OMAP24XX_SDRC_BASE+0x084)
+
+/* GPIO 1 */
+#define GPIO1_BASE GPIOX_BASE(1)
+#define GPIO1_REG32(offset) __REG32(GPIO1_BASE + (offset))
+#define GPIO1_IRQENABLE1 GPIO1_REG32(0x01C)
+#define GPIO1_IRQSTATUS1 GPIO1_REG32(0x018)
+#define GPIO1_IRQENABLE2 GPIO1_REG32(0x02C)
+#define GPIO1_IRQSTATUS2 GPIO1_REG32(0x028)
+#define GPIO1_WAKEUPENABLE GPIO1_REG32(0x020)
+#define GPIO1_RISINGDETECT GPIO1_REG32(0x048)
+#define GPIO1_DATAIN GPIO1_REG32(0x038)
+#define GPIO1_OE GPIO1_REG32(0x034)
+#define GPIO1_DATAOUT GPIO1_REG32(0x03C)
+
+/* GPIO2 */
+#define GPIO2_BASE GPIOX_BASE(2)
+#define GPIO2_REG32(offset) __REG32(GPIO2_BASE + (offset))
+#define GPIO2_IRQENABLE1 GPIO2_REG32(0x01C)
+#define GPIO2_IRQSTATUS1 GPIO2_REG32(0x018)
+#define GPIO2_IRQENABLE2 GPIO2_REG32(0x02C)
+#define GPIO2_IRQSTATUS2 GPIO2_REG32(0x028)
+#define GPIO2_WAKEUPENABLE GPIO2_REG32(0x020)
+#define GPIO2_RISINGDETECT GPIO2_REG32(0x048)
+#define GPIO2_DATAIN GPIO2_REG32(0x038)
+#define GPIO2_OE GPIO2_REG32(0x034)
+#define GPIO2_DATAOUT GPIO2_REG32(0x03C)
+
+/* GPIO 3 */
+#define GPIO3_BASE GPIOX_BASE(3)
+#define GPIO3_REG32(offset) __REG32(GPIO3_BASE + (offset))
+#define GPIO3_IRQENABLE1 GPIO3_REG32(0x01C)
+#define GPIO3_IRQSTATUS1 GPIO3_REG32(0x018)
+#define GPIO3_IRQENABLE2 GPIO3_REG32(0x02C)
+#define GPIO3_IRQSTATUS2 GPIO3_REG32(0x028)
+#define GPIO3_WAKEUPENABLE GPIO3_REG32(0x020)
+#define GPIO3_RISINGDETECT GPIO3_REG32(0x048)
+#define GPIO3_FALLINGDETECT GPIO3_REG32(0x04C)
+#define GPIO3_DATAIN GPIO3_REG32(0x038)
+#define GPIO3_OE GPIO3_REG32(0x034)
+#define GPIO3_DATAOUT GPIO3_REG32(0x03C)
+#define GPIO3_DEBOUNCENABLE GPIO3_REG32(0x050)
+#define GPIO3_DEBOUNCINGTIME GPIO3_REG32(0x054)
+
+/* GPIO 4 */
+#define GPIO4_BASE GPIOX_BASE(4)
+#define GPIO4_REG32(offset) __REG32(GPIO4_BASE + (offset))
+#define GPIO4_IRQENABLE1 GPIO4_REG32(0x01C)
+#define GPIO4_IRQSTATUS1 GPIO4_REG32(0x018)
+#define GPIO4_IRQENABLE2 GPIO4_REG32(0x02C)
+#define GPIO4_IRQSTATUS2 GPIO4_REG32(0x028)
+#define GPIO4_WAKEUPENABLE GPIO4_REG32(0x020)
+#define GPIO4_RISINGDETECT GPIO4_REG32(0x048)
+#define GPIO4_FALLINGDETECT GPIO4_REG32(0x04C)
+#define GPIO4_DATAIN GPIO4_REG32(0x038)
+#define GPIO4_OE GPIO4_REG32(0x034)
+#define GPIO4_DATAOUT GPIO4_REG32(0x03C)
+#define GPIO4_DEBOUNCENABLE GPIO4_REG32(0x050)
+#define GPIO4_DEBOUNCINGTIME GPIO4_REG32(0x054)
+
+
+/* IO CONFIG */
+#define CONTROL_BASE (OMAP24XX_CTRL_BASE)
+#define CONTROL_REG32(offset) __REG32(CONTROL_BASE + (offset))
+
+#define CONTROL_PADCONF_SPI1_NCS2 CONTROL_REG32(0x104)
+#define CONTROL_PADCONF_SYS_XTALOUT CONTROL_REG32(0x134)
+#define CONTROL_PADCONF_UART1_RX CONTROL_REG32(0x0C8)
+#define CONTROL_PADCONF_MCBSP1_DX CONTROL_REG32(0x10C)
+#define CONTROL_PADCONF_GPMC_NCS4 CONTROL_REG32(0x090)
+#define CONTROL_PADCONF_DSS_D5 CONTROL_REG32(0x0B8)
+#define CONTROL_PADCONF_DSS_D9 CONTROL_REG32(0x0BC)
+#define CONTROL_PADCONF_DSS_D13 CONTROL_REG32(0x0C0)
+#define CONTROL_PADCONF_DSS_VSYNC CONTROL_REG32(0x0CC)
+
+/* CONTROL */
+#define CONTROL_DEVCONF CONTROL_REG32(0x274)
+
+/* INTERRUPT CONTROLLER */
+#define INTC_BASE (OMAP24XX_L4_IO_BASE+0xfe000)
+#define INTC_REG32(offset) __REG32(INTC_BASE + (offset))
+
+#define INTC1_U_BASE INTC_REG32(0x000)
+#define INTC_MIR0 INTC_REG32(0x084)
+#define INTC_MIR_SET0 INTC_REG32(0x08C)
+#define INTC_MIR_CLEAR0 INTC_REG32(0x088)
+#define INTC_ISR_CLEAR0 INTC_REG32(0x094)
+#define INTC_MIR1 INTC_REG32(0x0A4)
+#define INTC_MIR_SET1 INTC_REG32(0x0AC)
+#define INTC_MIR_CLEAR1 INTC_REG32(0x0A8)
+#define INTC_ISR_CLEAR1 INTC_REG32(0x0B4)
+#define INTC_MIR2 INTC_REG32(0x0C4)
+#define INTC_MIR_SET2 INTC_REG32(0x0CC)
+#define INTC_MIR_CLEAR2 INTC_REG32(0x0C8)
+#define INTC_ISR_CLEAR2 INTC_REG32(0x0D4)
+#define INTC_SIR_IRQ INTC_REG32(0x040)
+#define INTC_CONTROL INTC_REG32(0x048)
+#define INTC_ILR11 INTC_REG32(0x12C)
+#define INTC_ILR32 INTC_REG32(0x180)
+#define INTC_ILR37 INTC_REG32(0x194)
+#define INTC_SYSCONFIG INTC_REG32(0x010)
+
+/* RAM FIREWALL */
+#define RAMFW_BASE (0x68005000)
+#define RAMFW_REG32(offset) __REG32(RAMFW_BASE + (offset))
+
+#define RAMFW_REQINFOPERM0 RAMFW_REG32(0x048)
+#define RAMFW_READPERM0 RAMFW_REG32(0x050)
+#define RAMFW_WRITEPERM0 RAMFW_REG32(0x058)
+
+/* GPMC CS1 FPGA ON USER INTERFACE MODULE */
+//#define DEBUG_BOARD_LED_REGISTER 0x04000014
+
+/* GPMC CS0 */
+#define GPMC_CONFIG1_0 GPMC_REG32(0x060)
+#define GPMC_CONFIG2_0 GPMC_REG32(0x064)
+#define GPMC_CONFIG3_0 GPMC_REG32(0x068)
+#define GPMC_CONFIG4_0 GPMC_REG32(0x06C)
+#define GPMC_CONFIG5_0 GPMC_REG32(0x070)
+#define GPMC_CONFIG6_0 GPMC_REG32(0x074)
+#define GPMC_CONFIG7_0 GPMC_REG32(0x078)
+
+/* DSS */
+#define DSS_CONTROL DISP_REG32(0x040)
+#define DISPC_CONTROL DISP_REG32(0x440)
+#define DISPC_SYSSTATUS DISP_REG32(0x414)
+#define DISPC_IRQSTATUS DISP_REG32(0x418)
+#define DISPC_IRQENABLE DISP_REG32(0x41C)
+#define DISPC_CONFIG DISP_REG32(0x444)
+#define DISPC_DEFAULT_COLOR0 DISP_REG32(0x44C)
+#define DISPC_DEFAULT_COLOR1 DISP_REG32(0x450)
+#define DISPC_TRANS_COLOR0 DISP_REG32(0x454)
+#define DISPC_TRANS_COLOR1 DISP_REG32(0x458)
+#define DISPC_LINE_NUMBER DISP_REG32(0x460)
+#define DISPC_TIMING_H DISP_REG32(0x464)
+#define DISPC_TIMING_V DISP_REG32(0x468)
+#define DISPC_POL_FREQ DISP_REG32(0x46C)
+#define DISPC_DIVISOR DISP_REG32(0x470)
+#define DISPC_SIZE_DIG DISP_REG32(0x478)
+#define DISPC_SIZE_LCD DISP_REG32(0x47C)
+#define DISPC_GFX_BA0 DISP_REG32(0x480)
+#define DISPC_GFX_BA1 DISP_REG32(0x484)
+#define DISPC_GFX_POSITION DISP_REG32(0x488)
+#define DISPC_GFX_SIZE DISP_REG32(0x48C)
+#define DISPC_GFX_ATTRIBUTES DISP_REG32(0x4A0)
+#define DISPC_GFX_FIFO_THRESHOLD DISP_REG32(0x4A4)
+#define DISPC_GFX_ROW_INC DISP_REG32(0x4AC)
+#define DISPC_GFX_PIXEL_INC DISP_REG32(0x4B0)
+#define DISPC_GFX_WINDOW_SKIP DISP_REG32(0x4B4)
+#define DISPC_GFX_TABLE_BA DISP_REG32(0x4B8)
+#define DISPC_DATA_CYCLE1 DISP_REG32(0x5D4)
+#define DISPC_DATA_CYCLE2 DISP_REG32(0x5D8)
+#define DISPC_DATA_CYCLE3 DISP_REG32(0x5DC)
+
+/* Wake up define for board */
+#define GPIO97 (1 << 1)
+#define GPIO88 (1 << 24)
+
+#endif /* __ASSEMBLER__ */
+
+#endif
+
+
+
+
+
--- /dev/null
+/*
+ * arch/arm/mach-omap/omap2/serial.c
+ *
+ * OMAP2 serial support.
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Paul Mundt <paul.mundt@nokia.com>
+ *
+ * Based off of arch/arm/mach-omap/omap1/serial.c
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+
+#include <asm/io.h>
+#include <asm/hardware/clock.h>
+
+#include <asm/arch/common.h>
+#include <asm/arch/board.h>
+
+static struct clk * uart1_ick = NULL;
+static struct clk * uart1_fck = NULL;
+static struct clk * uart2_ick = NULL;
+static struct clk * uart2_fck = NULL;
+static struct clk * uart3_ick = NULL;
+static struct clk * uart3_fck = NULL;
+
+static struct plat_serial8250_port serial_platform_data[] = {
+ {
+ .membase = (char *)IO_ADDRESS(OMAP_UART1_BASE),
+ .mapbase = (unsigned long)OMAP_UART1_BASE,
+ .irq = 72,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ }, {
+ .membase = (char *)IO_ADDRESS(OMAP_UART2_BASE),
+ .mapbase = (unsigned long)OMAP_UART2_BASE,
+ .irq = 73,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ }, {
+ .membase = (char *)IO_ADDRESS(OMAP_UART3_BASE),
+ .mapbase = (unsigned long)OMAP_UART3_BASE,
+ .irq = 74,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ }, {
+ .flags = 0
+ }
+};
+
+static inline unsigned int serial_read_reg(struct plat_serial8250_port *up,
+ int offset)
+{
+ offset <<= up->regshift;
+ return (unsigned int)__raw_readb(up->membase + offset);
+}
+
+static inline void serial_write_reg(struct plat_serial8250_port *p, int offset,
+ int value)
+{
+ offset <<= p->regshift;
+ __raw_writeb(value, (unsigned long)(p->membase + offset));
+}
+
+/*
+ * Internal UARTs need to be initialized for the 8250 autoconfig to work
+ * properly. Note that the TX watermark initialization may not be needed
+ * once the 8250.c watermark handling code is merged.
+ */
+static inline void __init omap_serial_reset(struct plat_serial8250_port *p)
+{
+ serial_write_reg(p, UART_OMAP_MDR1, 0x07);
+ serial_write_reg(p, UART_OMAP_SCR, 0x08);
+ serial_write_reg(p, UART_OMAP_MDR1, 0x00);
+ serial_write_reg(p, UART_OMAP_SYSC, 0x01);
+}
+
+void __init omap_serial_init()
+{
+ int i;
+ const struct omap_uart_config *info;
+
+ /*
+ * Make sure the serial ports are muxed on at this point.
+ * You have to mux them off in device drivers later on
+ * if not needed.
+ */
+
+ info = omap_get_config(OMAP_TAG_UART,
+ struct omap_uart_config);
+
+ if (info == NULL)
+ return;
+
+ for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
+ struct plat_serial8250_port *p = serial_platform_data + i;
+
+ if (!(info->enabled_uarts & (1 << i))) {
+ p->membase = 0;
+ p->mapbase = 0;
+ continue;
+ }
+
+ switch (i) {
+ case 0:
+ uart1_ick = clk_get(NULL, "uart1_ick");
+ if (IS_ERR(uart1_ick))
+ printk("Could not get uart1_ick\n");
+ else {
+ clk_use(uart1_ick);
+ }
+
+ uart1_fck = clk_get(NULL, "uart1_fck");
+ if (IS_ERR(uart1_fck))
+ printk("Could not get uart1_fck\n");
+ else {
+ clk_use(uart1_fck);
+ }
+ break;
+ case 1:
+ uart2_ick = clk_get(NULL, "uart2_ick");
+ if (IS_ERR(uart2_ick))
+ printk("Could not get uart2_ick\n");
+ else {
+ clk_use(uart2_ick);
+ }
+
+ uart2_fck = clk_get(NULL, "uart2_fck");
+ if (IS_ERR(uart2_fck))
+ printk("Could not get uart2_fck\n");
+ else {
+ clk_use(uart2_fck);
+ }
+ break;
+ case 2:
+ uart3_ick = clk_get(NULL, "uart3_ick");
+ if (IS_ERR(uart3_ick))
+ printk("Could not get uart3_ick\n");
+ else {
+ clk_use(uart3_ick);
+ }
+
+ uart3_fck = clk_get(NULL, "uart3_fck");
+ if (IS_ERR(uart3_fck))
+ printk("Could not get uart3_fck\n");
+ else {
+ clk_use(uart3_fck);
+ }
+ break;
+ }
+
+ omap_serial_reset(p);
+ }
+}
+
+static struct platform_device serial_device = {
+ .name = "serial8250",
+ .id = 0,
+ .dev = {
+ .platform_data = serial_platform_data,
+ },
+};
+
+static int __init omap_init(void)
+{
+ return platform_device_register(&serial_device);
+}
+arch_initcall(omap_init);
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/sram.S
+ *
+ * Omap2 specific functions that need to be run in internal SRAM
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <linux/config.h>
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/arch/io.h>
+#include <asm/hardware.h>
+
+#include <asm/arch/prcm.h>
+
+#define TIMER_32KSYNCT_CR_V IO_ADDRESS(OMAP24XX_32KSYNCT_BASE + 0x010)
+
+#define CM_CLKSEL2_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x544)
+#define PRCM_VOLTCTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x050)
+#define PRCM_CLKCFG_CTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x080)
+#define CM_CLKEN_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x500)
+#define CM_IDLEST_CKGEN_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x520)
+#define CM_CLKSEL1_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x540)
+
+#define SDRC_DLLA_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE + 0x060)
+#define SDRC_RFR_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE + 0x0a4)
+
+ .text
+
+ENTRY(sram_ddr_init)
+ stmfd sp!, {r0 - r12, lr} @ save registers on stack
+
+ mov r12, r2 @ capture CS1 vs CS0
+ mov r8, r3 @ capture force parameter
+
+ /* frequency shift down */
+ ldr r2, cm_clksel2_pll @ get address of dpllout reg
+ mov r3, #0x1 @ value for 1x operation
+ str r3, [r2] @ go to L1-freq operation
+
+ /* voltage shift down */
+ mov r9, #0x1 @ set up for L1 voltage call
+ bl voltage_shift @ go drop voltage
+
+ /* dll lock mode */
+ ldr r11, sdrc_dlla_ctrl @ addr of dlla ctrl
+ ldr r10, [r11] @ get current val
+ cmp r12, #0x1 @ cs1 base (2422 es2.05/1)
+ addeq r11, r11, #0x8 @ if cs1 base, move to DLLB
+ mvn r9, #0x4 @ mask to get clear bit2
+ and r10, r10, r9 @ clear bit2 for lock mode.
+ orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
+ orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz
+ str r10, [r11] @ commit to DLLA_CTRL
+ bl i_dll_wait @ wait for dll to lock
+
+ /* get dll value */
+ add r11, r11, #0x4 @ get addr of status reg
+ ldr r10, [r11] @ get locked value
+
+ /* voltage shift up */
+ mov r9, #0x0 @ shift back to L0-voltage
+ bl voltage_shift @ go raise voltage
+
+ /* frequency shift up */
+ mov r3, #0x2 @ value for 2x operation
+ str r3, [r2] @ go to L0-freq operation
+
+ /* reset entry mode for dllctrl */
+ sub r11, r11, #0x4 @ move from status to ctrl
+ cmp r12, #0x1 @ normalize if cs1 based
+ subeq r11, r11, #0x8 @ possibly back to DLLA
+ cmp r8, #0x1 @ if forced unlock exit
+ orreq r1, r1, #0x4 @ make sure exit with unlocked value
+ str r1, [r11] @ restore DLLA_CTRL high value
+ add r11, r11, #0x8 @ move to DLLB_CTRL addr
+ str r1, [r11] @ set value DLLB_CTRL
+ bl i_dll_wait @ wait for possible lock
+
+ /* set up for return, DDR should be good */
+ str r10, [r0] @ write dll_status and return counter
+ ldmfd sp!, {r0 - r12, pc} @ restore regs and return
+
+ /* ensure the DLL has relocked */
+i_dll_wait:
+ mov r4, #0x800 @ delay DLL relock, min 0x400 L3 clocks
+i_dll_delay:
+ subs r4, r4, #0x1
+ bne i_dll_delay
+ mov pc, lr
+
+ /*
+ * shift up or down voltage, use R9 as input to tell level.
+ * wait for it to finish, use 32k sync counter, 1tick=31uS.
+ */
+voltage_shift:
+ ldr r4, prcm_voltctrl @ get addr of volt ctrl.
+ ldr r5, [r4] @ get value.
+ ldr r6, prcm_mask_val @ get value of mask
+ and r5, r5, r6 @ apply mask to clear bits
+ orr r5, r5, r9 @ bulld value for L0/L1-volt operation.
+ str r5, [r4] @ set up for change.
+ mov r3, #0x4000 @ get val for force
+ orr r5, r5, r3 @ build value for force
+ str r5, [r4] @ Force transition to L1
+
+ ldr r3, timer_32ksynct_cr @ get addr of counter
+ ldr r5, [r3] @ get value
+ add r5, r5, #0x3 @ give it at most 93uS
+volt_delay:
+ ldr r7, [r3] @ get timer value
+ cmp r5, r7 @ time up?
+ bhi volt_delay @ not yet->branch
+ mov pc, lr @ back to caller.
+
+/* relative load constants */
+cm_clksel2_pll:
+ .word CM_CLKSEL2_PLL_V
+sdrc_dlla_ctrl:
+ .word SDRC_DLLA_CTRL_V
+prcm_voltctrl:
+ .word PRCM_VOLTCTRL_V
+prcm_mask_val:
+ .word 0xFFFF3FFC
+timer_32ksynct_cr:
+ .word TIMER_32KSYNCT_CR_V
+ENTRY(sram_ddr_init_sz)
+ .word . - sram_ddr_init
+
+/*
+ * Reprograms memory timings.
+ * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR]
+ * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0
+ */
+ENTRY(sram_reprogram_sdrc)
+ stmfd sp!, {r0 - r10, lr} @ save registers on stack
+ mov r3, #0x0 @ clear for mrc call
+ mcr p15, 0, r3, c7, c10, 4 @ memory barrier, finish ARM SDR/DDR
+ nop
+ nop
+ ldr r6, ddr_sdrc_rfr_ctrl @ get addr of refresh reg
+ ldr r5, [r6] @ get value
+ mov r5, r5, lsr #8 @ isolate rfr field and drop burst
+
+ cmp r0, #0x1 @ going to half speed?
+ movne r9, #0x0 @ if up set flag up for pre up, hi volt
+
+ blne voltage_shift_c @ adjust voltage
+
+ cmp r0, #0x1 @ going to half speed (post branch link)
+ moveq r5, r5, lsr #1 @ divide by 2 if to half
+ movne r5, r5, lsl #1 @ mult by 2 if to full
+ mov r5, r5, lsl #8 @ put rfr field back into place
+ add r5, r5, #0x1 @ turn on burst of 1
+ ldr r4, ddr_cm_clksel2_pll @ get address of out reg
+ ldr r3, [r4] @ get curr value
+ orr r3, r3, #0x3
+ bic r3, r3, #0x3 @ clear lower bits
+ orr r3, r3, r0 @ new state value
+ str r3, [r4] @ set new state (pll/x, x=1 or 2)
+ nop
+ nop
+
+ moveq r9, #0x1 @ if speed down, post down, drop volt
+ bleq voltage_shift_c
+
+ mcr p15, 0, r3, c7, c10, 4 @ memory barrier
+ str r5, [r6] @ set new RFR_1 value
+ add r6, r6, #0x30 @ get RFR_2 addr
+ str r5, [r6] @ set RFR_2
+ nop
+ cmp r2, #0x1 @ (SDR or DDR) do we need to adjust DLL
+ bne freq_out @ leave if SDR, no DLL function
+
+ /* With DDR, we need to take care of the DLL for the frequency change */
+ ldr r2, ddr_sdrc_dlla_ctrl @ addr of dlla ctrl
+ str r1, [r2] @ write out new SDRC_DLLA_CTRL
+ add r2, r2, #0x8 @ addr to SDRC_DLLB_CTRL
+ str r1, [r2] @ commit to SDRC_DLLB_CTRL
+ mov r1, #0x2000 @ wait DLL relock, min 0x400 L3 clocks
+dll_wait:
+ subs r1, r1, #0x1
+ bne dll_wait
+freq_out:
+ ldmfd sp!, {r0 - r10, pc} @ restore regs and return
+
+ /*
+ * shift up or down voltage, use R9 as input to tell level.
+ * wait for it to finish, use 32k sync counter, 1tick=31uS.
+ */
+voltage_shift_c:
+ ldr r10, ddr_prcm_voltctrl @ get addr of volt ctrl
+ ldr r8, [r10] @ get value
+ ldr r7, ddr_prcm_mask_val @ get value of mask
+ and r8, r8, r7 @ apply mask to clear bits
+ orr r8, r8, r9 @ bulld value for L0/L1-volt operation.
+ str r8, [r10] @ set up for change.
+ mov r7, #0x4000 @ get val for force
+ orr r8, r8, r7 @ build value for force
+ str r8, [r10] @ Force transition to L1
+
+ ldr r10, ddr_timer_32ksynct @ get addr of counter
+ ldr r8, [r10] @ get value
+ add r8, r8, #0x2 @ give it at most 62uS (min 31+)
+volt_delay_c:
+ ldr r7, [r10] @ get timer value
+ cmp r8, r7 @ time up?
+ bhi volt_delay_c @ not yet->branch
+ mov pc, lr @ back to caller
+
+ddr_cm_clksel2_pll:
+ .word CM_CLKSEL2_PLL_V
+ddr_sdrc_dlla_ctrl:
+ .word SDRC_DLLA_CTRL_V
+ddr_sdrc_rfr_ctrl:
+ .word SDRC_RFR_CTRL_V
+ddr_prcm_voltctrl:
+ .word PRCM_VOLTCTRL_V
+ddr_prcm_mask_val:
+ .word 0xFFFF3FFC
+ddr_timer_32ksynct:
+ .word TIMER_32KSYNCT_CR_V
+
+ENTRY(sram_reprogram_sdrc_sz)
+ .word . - sram_reprogram_sdrc
+
+/*
+ * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode.
+ */
+ENTRY(sram_set_prcm)
+ stmfd sp!, {r0-r12, lr} @ regs to stack
+ adr r4, pbegin @ addr of preload start
+ adr r8, pend @ addr of preload end
+ mcrr p15, 1, r8, r4, c12 @ preload into icache
+pbegin:
+ /* move into fast relock bypass */
+ ldr r8, pll_ctl @ get addr
+ ldr r5, [r8] @ get val
+ mvn r6, #0x3 @ clear mask
+ and r5, r5, r6 @ clear field
+ orr r7, r5, #0x2 @ fast relock val
+ str r7, [r8] @ go to fast relock
+ ldr r4, pll_stat @ addr of stat
+block:
+ /* wait for bypass */
+ ldr r8, [r4] @ stat value
+ and r8, r8, #0x3 @ mask for stat
+ cmp r8, #0x1 @ there yet
+ bne block @ loop if not
+
+ /* set new dpll dividers _after_ in bypass */
+ ldr r4, pll_div @ get addr
+ str r0, [r4] @ set dpll ctrl val
+
+ ldr r4, set_config @ get addr
+ mov r8, #1 @ valid cfg msk
+ str r8, [r4] @ make dividers take
+
+ mov r4, #100 @ dead spin a bit
+wait_a_bit:
+ subs r4, r4, #1 @ dec loop
+ bne wait_a_bit @ delay done?
+
+ /* check if staying in bypass */
+ cmp r2, #0x1 @ stay in bypass?
+ beq pend @ jump over dpll relock
+
+ /* relock DPLL with new vals */
+ ldr r5, pll_stat @ get addr
+ ldr r4, pll_ctl @ get addr
+ orr r8, r7, #0x3 @ val for lock dpll
+ str r8, [r4] @ set val
+ mov r0, #1000 @ dead spin a bit
+wait_more:
+ subs r0, r0, #1 @ dec loop
+ bne wait_more @ delay done?
+wait_lock:
+ ldr r8, [r5] @ get lock val
+ and r8, r8, #3 @ isolate field
+ cmp r8, #2 @ locked?
+ bne wait_lock @ wait if not
+pend:
+ /* update memory timings & briefly lock dll */
+ ldr r4, sdrc_rfr @ get addr
+ str r1, [r4] @ update refresh timing
+ ldr r11, dlla_ctrl @ get addr of DLLA ctrl
+ ldr r10, [r11] @ get current val
+ mvn r9, #0x4 @ mask to get clear bit2
+ and r10, r10, r9 @ clear bit2 for lock mode
+ orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
+ str r10, [r11] @ commit to DLLA_CTRL
+ add r11, r11, #0x8 @ move to dllb
+ str r10, [r11] @ hit DLLB also
+
+ mov r4, #0x800 @ relock time (min 0x400 L3 clocks)
+wait_dll_lock:
+ subs r4, r4, #0x1
+ bne wait_dll_lock
+ nop
+ ldmfd sp!, {r0-r12, pc} @ restore regs and return
+
+set_config:
+ .word PRCM_CLKCFG_CTRL_V
+pll_ctl:
+ .word CM_CLKEN_PLL_V
+pll_stat:
+ .word CM_IDLEST_CKGEN_V
+pll_div:
+ .word CM_CLKSEL1_PLL_V
+sdrc_rfr:
+ .word SDRC_RFR_CTRL_V
+dlla_ctrl:
+ .word SDRC_DLLA_CTRL_V
+
+ENTRY(sram_set_prcm_sz)
+ .word . - sram_set_prcm
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap2/timer-gp.c
+ *
+ * OMAP2 GP timer support.
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Paul Mundt <paul.mundt@nokia.com>
+ * Juha Yrjölä <juha.yrjola@nokia.com>
+ *
+ * Some parts based off of TI's 24xx code:
+ *
+ * Copyright (C) 2004 Texas Instruments, Inc.
+ *
+ * Roughly modelled after the OMAP1 MPU timer code.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/interrupt.h>
+#include <linux/err.h>
+#include <asm/mach/time.h>
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/hardware/clock.h>
+
+#define OMAP2_GP_TIMER1_BASE 0x48028000
+#define OMAP2_GP_TIMER2_BASE 0x4802a000
+#define OMAP2_GP_TIMER3_BASE 0x48078000
+#define OMAP2_GP_TIMER4_BASE 0x4807a000
+
+#define GP_TIMER_TIDR 0x00
+#define GP_TIMER_TISR 0x18
+#define GP_TIMER_TIER 0x1c
+#define GP_TIMER_TCLR 0x24
+#define GP_TIMER_TCRR 0x28
+#define GP_TIMER_TLDR 0x2c
+#define GP_TIMER_TSICR 0x40
+
+#define OS_TIMER_NR 1 /* GP timer 2 */
+
+static unsigned long timer_base[] = {
+ IO_ADDRESS(OMAP2_GP_TIMER1_BASE),
+ IO_ADDRESS(OMAP2_GP_TIMER2_BASE),
+ IO_ADDRESS(OMAP2_GP_TIMER3_BASE),
+ IO_ADDRESS(OMAP2_GP_TIMER4_BASE),
+};
+
+static inline unsigned int timer_read_reg(int nr, unsigned int reg)
+{
+ return __raw_readl(timer_base[nr] + reg);
+}
+
+static inline void timer_write_reg(int nr, unsigned int reg, unsigned int val)
+{
+ __raw_writel(val, timer_base[nr] + reg);
+}
+
+/* Note that we always enable the clock prescale divider bit */
+static inline void omap2_gp_timer_start(int nr, unsigned long load_val)
+{
+ unsigned int tmp;
+
+ tmp = 0xffffffff - load_val;
+
+ timer_write_reg(nr, GP_TIMER_TLDR, tmp);
+ timer_write_reg(nr, GP_TIMER_TCRR, tmp);
+ timer_write_reg(nr, GP_TIMER_TIER, 1 << 1);
+ timer_write_reg(nr, GP_TIMER_TCLR, (1 << 5) | (1 << 1) | 1);
+}
+
+static irqreturn_t omap2_gp_timer_interrupt(int irq, void *dev_id,
+ struct pt_regs *regs)
+{
+ write_seqlock(&xtime_lock);
+
+ timer_write_reg(OS_TIMER_NR, GP_TIMER_TISR, 1 << 1);
+ timer_tick(regs);
+
+ write_sequnlock(&xtime_lock);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction omap2_gp_timer_irq = {
+ .name = "gp timer",
+ .flags = SA_INTERRUPT,
+ .handler = omap2_gp_timer_interrupt,
+};
+
+static void __init omap2_gp_timer_init(void)
+{
+ struct clk * sys_ck;
+ u32 tick_period = 120000;
+ u32 l;
+
+ /* Reset clock and prescale value */
+ timer_write_reg(OS_TIMER_NR, GP_TIMER_TCLR, 0);
+
+ sys_ck = clk_get(NULL, "sys_ck");
+ if (IS_ERR(sys_ck))
+ printk(KERN_ERR "Could not get sys_ck\n");
+ else {
+ clk_use(sys_ck);
+ tick_period = clk_get_rate(sys_ck) / 100;
+ clk_put(sys_ck);
+ }
+
+ tick_period /= 2; /* Minimum prescale divider is 2 */
+ tick_period -= 1;
+
+ l = timer_read_reg(OS_TIMER_NR, GP_TIMER_TIDR);
+ printk(KERN_INFO "OMAP2 GP timer (HW version %d.%d)\n",
+ (l >> 4) & 0x0f, l & 0x0f);
+
+ setup_irq(38, &omap2_gp_timer_irq);
+
+ omap2_gp_timer_start(OS_TIMER_NR, tick_period);
+}
+
+struct sys_timer omap_timer = {
+ .init = omap2_gp_timer_init,
+};
+
# ARMv6
config CPU_V6
bool "Support ARM V6 processor"
- depends on ARCH_INTEGRATOR || MACH_REALVIEW_EB
+ depends on ARCH_INTEGRATOR || MACH_REALVIEW_EB || ARCH_OMAP2
select CPU_32v6
select CPU_ABRT_EV6
select CPU_CACHE_V6
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff