pixclockpol:POLARITY
pixel clock polarity
0 => falling edge, 1 => rising edge
+
+
+Overlay Support for PXA27x and later LCD controllers
+====================================================
+
+ PXA27x and later processors support overlay1 and overlay2 on-top of the
+ base framebuffer (although under-neath the base is also possible). They
+ support palette and no-palette RGB formats, as well as YUV formats (only
+ available on overlay2). These overlays have dedicated DMA channels and
+ behave in a similar way as a framebuffer.
+
+ However, there are some differences between these overlay framebuffers
+ and normal framebuffers, as listed below:
+
+ 1. overlay can start at a 32-bit word aligned position within the base
+ framebuffer, which means they have a start (x, y). This information
+ is encoded into var->nonstd (no, var->xoffset and var->yoffset are
+ not for such purpose).
+
+ 2. overlay framebuffer is allocated dynamically according to specified
+ 'struct fb_var_screeninfo', the amount is decided by:
+
+ var->xres_virtual * var->yres_virtual * bpp
+
+ bpp = 16 -- for RGB565 or RGBT555
+ = 24 -- for YUV444 packed
+ = 24 -- for YUV444 planar
+ = 16 -- for YUV422 planar (1 pixel = 1 Y + 1/2 Cb + 1/2 Cr)
+ = 12 -- for YUV420 planar (1 pixel = 1 Y + 1/4 Cb + 1/4 Cr)
+
+ NOTE:
+
+ a. overlay does not support panning in x-direction, thus
+ var->xres_virtual will always be equal to var->xres
+
+ b. line length of overlay(s) must be on a 32-bit word boundary,
+ for YUV planar modes, it is a requirement for the component
+ with minimum bits per pixel, e.g. for YUV420, Cr component
+ for one pixel is actually 2-bits, it means the line length
+ should be a multiple of 16-pixels
+
+ c. starting horizontal position (XPOS) should start on a 32-bit
+ word boundary, otherwise the fb_check_var() will just fail.
+
+ d. the rectangle of the overlay should be within the base plane,
+ otherwise fail
+
+ Applications should follow the sequence below to operate an overlay
+ framebuffer:
+
+ a. open("/dev/fb[1-2]", ...)
+ b. ioctl(fd, FBIOGET_VSCREENINFO, ...)
+ c. modify 'var' with desired parameters:
+ 1) var->xres and var->yres
+ 2) larger var->yres_virtual if more memory is required,
+ usually for double-buffering
+ 3) var->nonstd for starting (x, y) and color format
+ 4) var->{red, green, blue, transp} if RGB mode is to be used
+ d. ioctl(fd, FBIOPUT_VSCREENINFO, ...)
+ e. ioctl(fd, FBIOGET_FSCREENINFO, ...)
+ f. mmap
+ g. ...
+
+ 3. for YUV planar formats, these are actually not supported within the
+ framebuffer framework, application has to take care of the offsets
+ and lengths of each component within the framebuffer.
+
+ 4. var->nonstd is used to pass starting (x, y) position and color format,
+ the detailed bit fields are shown below:
+
+ 31 23 20 10 0
+ +-----------------+---+----------+----------+
+ | ... unused ... |FOR| XPOS | YPOS |
+ +-----------------+---+----------+----------+
+
+ FOR - color format, as defined by OVERLAY_FORMAT_* in pxafb.h
+ 0 - RGB
+ 1 - YUV444 PACKED
+ 2 - YUV444 PLANAR
+ 3 - YUV422 PLANAR
+ 4 - YUR420 PLANAR
+
+ XPOS - starting horizontal position
+ YPOS - starting vertical position
*
* linux-arm-kernel@lists.arm.linux.org.uk
*
+ * Add support for overlay1 and overlay2 based on pxafb_overlay.c:
+ *
+ * Copyright (C) 2004, Intel Corporation
+ *
+ * 2003/08/27: <yu.tang@intel.com>
+ * 2004/03/10: <stanley.cai@intel.com>
+ * 2004/10/28: <yan.yin@intel.com>
+ *
+ * Copyright (C) 2006-2008 Marvell International Ltd.
+ * All Rights Reserved
*/
#include <linux/module.h>
struct pxafb_info *);
static void set_ctrlr_state(struct pxafb_info *fbi, u_int state);
static void setup_base_frame(struct pxafb_info *fbi, int branch);
+static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal,
+ unsigned long offset, size_t size);
static unsigned long video_mem_size = 0;
.fb_blank = pxafb_blank,
};
+#ifdef CONFIG_FB_PXA_OVERLAY
+static void overlay1fb_setup(struct pxafb_layer *ofb)
+{
+ int size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual;
+ unsigned long start = ofb->video_mem_phys;
+ setup_frame_dma(ofb->fbi, DMA_OV1, PAL_NONE, start, size);
+}
+
+/* Depending on the enable status of overlay1/2, the DMA should be
+ * updated from FDADRx (when disabled) or FBRx (when enabled).
+ */
+static void overlay1fb_enable(struct pxafb_layer *ofb)
+{
+ int enabled = lcd_readl(ofb->fbi, OVL1C1) & OVLxC1_OEN;
+ uint32_t fdadr1 = ofb->fbi->fdadr[DMA_OV1] | (enabled ? 0x1 : 0);
+
+ lcd_writel(ofb->fbi, enabled ? FBR1 : FDADR1, fdadr1);
+ lcd_writel(ofb->fbi, OVL1C2, ofb->control[1]);
+ lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] | OVLxC1_OEN);
+}
+
+static void overlay1fb_disable(struct pxafb_layer *ofb)
+{
+ uint32_t lccr5 = lcd_readl(ofb->fbi, LCCR5);
+
+ lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] & ~OVLxC1_OEN);
+
+ lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(1));
+ lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(1));
+ lcd_writel(ofb->fbi, FBR1, ofb->fbi->fdadr[DMA_OV1] | 0x3);
+
+ if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0)
+ pr_warning("%s: timeout disabling overlay1\n", __func__);
+
+ lcd_writel(ofb->fbi, LCCR5, lccr5);
+}
+
+static void overlay2fb_setup(struct pxafb_layer *ofb)
+{
+ int size, div = 1, pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd);
+ unsigned long start[3] = { ofb->video_mem_phys, 0, 0 };
+
+ if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED) {
+ size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual;
+ setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size);
+ } else {
+ size = ofb->fb.var.xres_virtual * ofb->fb.var.yres_virtual;
+ switch (pfor) {
+ case OVERLAY_FORMAT_YUV444_PLANAR: div = 1; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: div = 2; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: div = 4; break;
+ }
+ start[1] = start[0] + size;
+ start[2] = start[1] + size / div;
+ setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size);
+ setup_frame_dma(ofb->fbi, DMA_OV2_Cb, -1, start[1], size / div);
+ setup_frame_dma(ofb->fbi, DMA_OV2_Cr, -1, start[2], size / div);
+ }
+}
+
+static void overlay2fb_enable(struct pxafb_layer *ofb)
+{
+ int pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd);
+ int enabled = lcd_readl(ofb->fbi, OVL2C1) & OVLxC1_OEN;
+ uint32_t fdadr2 = ofb->fbi->fdadr[DMA_OV2_Y] | (enabled ? 0x1 : 0);
+ uint32_t fdadr3 = ofb->fbi->fdadr[DMA_OV2_Cb] | (enabled ? 0x1 : 0);
+ uint32_t fdadr4 = ofb->fbi->fdadr[DMA_OV2_Cr] | (enabled ? 0x1 : 0);
+
+ if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED)
+ lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2);
+ else {
+ lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2);
+ lcd_writel(ofb->fbi, enabled ? FBR3 : FDADR3, fdadr3);
+ lcd_writel(ofb->fbi, enabled ? FBR4 : FDADR4, fdadr4);
+ }
+ lcd_writel(ofb->fbi, OVL2C2, ofb->control[1]);
+ lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] | OVLxC1_OEN);
+}
+
+static void overlay2fb_disable(struct pxafb_layer *ofb)
+{
+ uint32_t lccr5 = lcd_readl(ofb->fbi, LCCR5);
+
+ lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] & ~OVLxC1_OEN);
+
+ lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(2));
+ lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(2));
+ lcd_writel(ofb->fbi, FBR2, ofb->fbi->fdadr[DMA_OV2_Y] | 0x3);
+ lcd_writel(ofb->fbi, FBR3, ofb->fbi->fdadr[DMA_OV2_Cb] | 0x3);
+ lcd_writel(ofb->fbi, FBR4, ofb->fbi->fdadr[DMA_OV2_Cr] | 0x3);
+
+ if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0)
+ pr_warning("%s: timeout disabling overlay2\n", __func__);
+}
+
+static struct pxafb_layer_ops ofb_ops[] = {
+ [0] = {
+ .enable = overlay1fb_enable,
+ .disable = overlay1fb_disable,
+ .setup = overlay1fb_setup,
+ },
+ [1] = {
+ .enable = overlay2fb_enable,
+ .disable = overlay2fb_disable,
+ .setup = overlay2fb_setup,
+ },
+};
+
+static int overlayfb_open(struct fb_info *info, int user)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer *)info;
+
+ /* no support for framebuffer console on overlay */
+ if (user == 0)
+ return -ENODEV;
+
+ /* allow only one user at a time */
+ if (atomic_inc_and_test(&ofb->usage))
+ return -EBUSY;
+
+ /* unblank the base framebuffer */
+ fb_blank(&ofb->fbi->fb, FB_BLANK_UNBLANK);
+ return 0;
+}
+
+static int overlayfb_release(struct fb_info *info, int user)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer*) info;
+
+ atomic_dec(&ofb->usage);
+ ofb->ops->disable(ofb);
+
+ free_pages_exact(ofb->video_mem, ofb->video_mem_size);
+ ofb->video_mem = NULL;
+ ofb->video_mem_size = 0;
+ return 0;
+}
+
+static int overlayfb_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer *)info;
+ struct fb_var_screeninfo *base_var = &ofb->fbi->fb.var;
+ int xpos, ypos, pfor, bpp;
+
+ xpos = NONSTD_TO_XPOS(var->nonstd);
+ ypos = NONSTD_TO_XPOS(var->nonstd);
+ pfor = NONSTD_TO_PFOR(var->nonstd);
+
+ bpp = pxafb_var_to_bpp(var);
+ if (bpp < 0)
+ return -EINVAL;
+
+ /* no support for YUV format on overlay1 */
+ if (ofb->id == OVERLAY1 && pfor != 0)
+ return -EINVAL;
+
+ /* for YUV packed formats, bpp = 'minimum bpp of YUV components' */
+ switch (pfor) {
+ case OVERLAY_FORMAT_RGB:
+ bpp = pxafb_var_to_bpp(var);
+ if (bpp < 0)
+ return -EINVAL;
+
+ pxafb_set_pixfmt(var, var_to_depth(var));
+ break;
+ case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 8; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 4; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 2; break;
+ default:
+ return -EINVAL;
+ }
+
+ /* each line must start at a 32-bit word boundary */
+ if ((xpos * bpp) % 32)
+ return -EINVAL;
+
+ /* xres must align on 32-bit word boundary */
+ var->xres = roundup(var->xres * bpp, 32) / bpp;
+
+ if ((xpos + var->xres > base_var->xres) ||
+ (ypos + var->yres > base_var->yres))
+ return -EINVAL;
+
+ var->xres_virtual = var->xres;
+ var->yres_virtual = max(var->yres, var->yres_virtual);
+ return 0;
+}
+
+static int overlayfb_map_video_memory(struct pxafb_layer *ofb)
+{
+ struct fb_var_screeninfo *var = &ofb->fb.var;
+ int pfor = NONSTD_TO_PFOR(var->nonstd);
+ int size, bpp = 0;
+
+ switch (pfor) {
+ case OVERLAY_FORMAT_RGB: bpp = var->bits_per_pixel; break;
+ case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 16; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 12; break;
+ }
+
+ ofb->fb.fix.line_length = var->xres_virtual * bpp / 8;
+
+ size = PAGE_ALIGN(ofb->fb.fix.line_length * var->yres_virtual);
+
+ /* don't re-allocate if the original video memory is enough */
+ if (ofb->video_mem) {
+ if (ofb->video_mem_size >= size)
+ return 0;
+
+ free_pages_exact(ofb->video_mem, ofb->video_mem_size);
+ }
+
+ ofb->video_mem = alloc_pages_exact(size, GFP_KERNEL | __GFP_ZERO);
+ if (ofb->video_mem == NULL)
+ return -ENOMEM;
+
+ ofb->video_mem_phys = virt_to_phys(ofb->video_mem);
+ ofb->video_mem_size = size;
+
+ ofb->fb.fix.smem_start = ofb->video_mem_phys;
+ ofb->fb.fix.smem_len = ofb->fb.fix.line_length * var->yres_virtual;
+ ofb->fb.screen_base = ofb->video_mem;
+ return 0;
+}
+
+static int overlayfb_set_par(struct fb_info *info)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer *)info;
+ struct fb_var_screeninfo *var = &info->var;
+ int xpos, ypos, pfor, bpp, ret;
+
+ ret = overlayfb_map_video_memory(ofb);
+ if (ret)
+ return ret;
+
+ bpp = pxafb_var_to_bpp(var);
+ xpos = NONSTD_TO_XPOS(var->nonstd);
+ ypos = NONSTD_TO_XPOS(var->nonstd);
+ pfor = NONSTD_TO_PFOR(var->nonstd);
+
+ ofb->control[0] = OVLxC1_PPL(var->xres) | OVLxC1_LPO(var->yres) |
+ OVLxC1_BPP(bpp);
+ ofb->control[1] = OVLxC2_XPOS(xpos) | OVLxC2_YPOS(ypos);
+
+ if (ofb->id == OVERLAY2)
+ ofb->control[1] |= OVL2C2_PFOR(pfor);
+
+ ofb->ops->setup(ofb);
+ ofb->ops->enable(ofb);
+ return 0;
+}
+
+static struct fb_ops overlay_fb_ops = {
+ .owner = THIS_MODULE,
+ .fb_open = overlayfb_open,
+ .fb_release = overlayfb_release,
+ .fb_check_var = overlayfb_check_var,
+ .fb_set_par = overlayfb_set_par,
+};
+
+static void __devinit init_pxafb_overlay(struct pxafb_info *fbi,
+ struct pxafb_layer *ofb, int id)
+{
+ sprintf(ofb->fb.fix.id, "overlay%d", id + 1);
+
+ ofb->fb.fix.type = FB_TYPE_PACKED_PIXELS;
+ ofb->fb.fix.xpanstep = 0;
+ ofb->fb.fix.ypanstep = 1;
+
+ ofb->fb.var.activate = FB_ACTIVATE_NOW;
+ ofb->fb.var.height = -1;
+ ofb->fb.var.width = -1;
+ ofb->fb.var.vmode = FB_VMODE_NONINTERLACED;
+
+ ofb->fb.fbops = &overlay_fb_ops;
+ ofb->fb.flags = FBINFO_FLAG_DEFAULT;
+ ofb->fb.node = -1;
+ ofb->fb.pseudo_palette = NULL;
+
+ ofb->id = id;
+ ofb->ops = &ofb_ops[id];
+ atomic_set(&ofb->usage, 0);
+ ofb->fbi = fbi;
+ init_completion(&ofb->branch_done);
+}
+
+static int __devinit pxafb_overlay_init(struct pxafb_info *fbi)
+{
+ int i, ret;
+
+ for (i = 0; i < 2; i++) {
+ init_pxafb_overlay(fbi, &fbi->overlay[i], i);
+ ret = register_framebuffer(&fbi->overlay[i].fb);
+ if (ret) {
+ dev_err(fbi->dev, "failed to register overlay %d\n", i);
+ return ret;
+ }
+ }
+
+ /* mask all IU/BS/EOF/SOF interrupts */
+ lcd_writel(fbi, LCCR5, ~0);
+
+ /* place overlay(s) on top of base */
+ fbi->lccr0 |= LCCR0_OUC;
+ pr_info("PXA Overlay driver loaded successfully!\n");
+ return 0;
+}
+
+static void __devexit pxafb_overlay_exit(struct pxafb_info *fbi)
+{
+ int i;
+
+ for (i = 0; i < 2; i++)
+ unregister_framebuffer(&fbi->overlay[i].fb);
+}
+#else
+static inline void pxafb_overlay_init(struct pxafb_info *fbi) {}
+static inline void pxafb_overlay_exit(struct pxafb_info *fbi) {}
+#endif /* CONFIG_FB_PXA_OVERLAY */
+
/*
* Calculate the PCD value from the clock rate (in picoseconds).
* We take account of the PPCR clock setting.
EXPORT_SYMBOL(pxafb_get_hsync_time);
static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal,
- unsigned int offset, size_t size)
+ unsigned long start, size_t size)
{
struct pxafb_dma_descriptor *dma_desc, *pal_desc;
unsigned int dma_desc_off, pal_desc_off;
dma_desc = &fbi->dma_buff->dma_desc[dma];
dma_desc_off = offsetof(struct pxafb_dma_buff, dma_desc[dma]);
- dma_desc->fsadr = fbi->video_mem_phys + offset;
+ dma_desc->fsadr = start;
dma_desc->fidr = 0;
dma_desc->ldcmd = size;
{
struct fb_var_screeninfo *var = &fbi->fb.var;
struct fb_fix_screeninfo *fix = &fbi->fb.fix;
- unsigned int nbytes, offset;
- int dma, pal, bpp = var->bits_per_pixel;
+ int nbytes, dma, pal, bpp = var->bits_per_pixel;
+ unsigned long offset;
dma = DMA_BASE + (branch ? DMA_MAX : 0);
pal = (bpp >= 16) ? PAL_NONE : PAL_BASE + (branch ? PAL_MAX : 0);
nbytes = fix->line_length * var->yres;
- offset = fix->line_length * var->yoffset;
+ offset = fix->line_length * var->yoffset + fbi->video_mem_phys;
if (fbi->lccr0 & LCCR0_SDS) {
nbytes = nbytes / 2;
static irqreturn_t pxafb_handle_irq(int irq, void *dev_id)
{
struct pxafb_info *fbi = dev_id;
- unsigned int lccr0, lcsr = lcd_readl(fbi, LCSR);
+ unsigned int lccr0, lcsr, lcsr1;
+ lcsr = lcd_readl(fbi, LCSR);
if (lcsr & LCSR_LDD) {
lccr0 = lcd_readl(fbi, LCCR0);
lcd_writel(fbi, LCCR0, lccr0 | LCCR0_LDM);
if (lcsr & LCSR_CMD_INT)
complete(&fbi->command_done);
#endif
-
lcd_writel(fbi, LCSR, lcsr);
+
+#ifdef CONFIG_FB_PXA_OVERLAY
+ lcsr1 = lcd_readl(fbi, LCSR1);
+ if (lcsr1 & LCSR1_BS(1))
+ complete(&fbi->overlay[0].branch_done);
+
+ if (lcsr1 & LCSR1_BS(2))
+ complete(&fbi->overlay[1].branch_done);
+
+ lcd_writel(fbi, LCSR1, lcsr1);
+#endif
return IRQ_HANDLED;
}
goto failed_free_cmap;
}
+ pxafb_overlay_init(fbi);
+
#ifdef CONFIG_CPU_FREQ
fbi->freq_transition.notifier_call = pxafb_freq_transition;
fbi->freq_policy.notifier_call = pxafb_freq_policy;
info = &fbi->fb;
+ pxafb_overlay_exit(fbi);
unregister_framebuffer(info);
pxafb_disable_controller(fbi);
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff