/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitTimer |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TimerNbr, |
-| BYTE_ b_TimerMode, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TimerNbr, |
+| unsigned char_ b_TimerMode, |
| ULONG_ ul_ReloadValue, |
-| BYTE_ b_InputClockSelection, |
-| BYTE_ b_InputClockLevel, |
-| BYTE_ b_OutputLevel, |
-| BYTE_ b_HardwareGateLevel)
+| unsigned char_ b_InputClockSelection, |
+| unsigned char_ b_InputClockLevel, |
+| unsigned char_ b_OutputLevel, |
+| unsigned char_ b_HardwareGateLevel)
INT i_InsnConfig_InitTimer(struct comedi_device *dev,struct comedi_subdevice *s,
struct comedi_insn *insn,unsigned int *data)
|
| +--------------------------------+------------------------------------+ |
| |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board |
| APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to |
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
-| BYTE_ b_TimerNbr : Timer number to |
+| unsigned char_ b_TimerNbr : Timer number to |
| configure (0 to 2) |
-| BYTE_ b_TimerMode : Timer mode selection |
+| unsigned char_ b_TimerMode : Timer mode selection |
| (0 to 5) |
| 0: Interrupt on terminal|
| count |
| or division factor |
| See timer mode |
| description table. |
-| BYTE_ b_InputClockSelection : Selection from input |
+| unsigned char_ b_InputClockSelection : Selection from input |
| timer clock. |
| See input clock |
| selection table. |
-| BYTE_ b_InputClockLevel : Selection from input |
+| unsigned char_ b_InputClockLevel : Selection from input |
| clock level. |
| 0 : Low active |
| (Input inverted) |
| 1 : High active |
-| BYTE_ b_OutputLevel, : Selection from output |
+| unsigned char_ b_OutputLevel, : Selection from output |
| clock level. |
| 0 : Low active |
| 1 : High active |
| (Output inverted) |
-| BYTE_ b_HardwareGateLevel : Selection from |
+| unsigned char_ b_HardwareGateLevel : Selection from |
| hardware gate level. |
| 0 : Low active |
| (Input inverted) |
| If you will not used |
| the hardware gate set |
| this value to 0.
-|b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_TimerNbr = (BYTE) CR_CHAN(insn->chanspec);
- b_TimerMode = (BYTE) data[0];
+|b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_TimerNbr = (unsigned char) CR_CHAN(insn->chanspec);
+ b_TimerMode = (unsigned char) data[0];
ul_ReloadValue = (ULONG) data[1];
- b_InputClockSelection =(BYTE) data[2];
- b_InputClockLevel =(BYTE) data[3];
- b_OutputLevel =(BYTE) data[4];
- b_HardwareGateLevel =(BYTE) data[5];
+ b_InputClockSelection =(unsigned char) data[2];
+ b_InputClockLevel =(unsigned char) data[3];
+ b_OutputLevel =(unsigned char) data[4];
+ b_HardwareGateLevel =(unsigned char) data[5];
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
{
INT i_ReturnValue = 0;
- BYTE b_ModulNbr;
- BYTE b_TimerNbr;
- BYTE b_TimerMode;
+ unsigned char b_ModulNbr;
+ unsigned char b_TimerNbr;
+ unsigned char b_TimerMode;
ULONG ul_ReloadValue;
- BYTE b_InputClockSelection;
- BYTE b_InputClockLevel;
- BYTE b_OutputLevel;
- BYTE b_HardwareGateLevel;
+ unsigned char b_InputClockSelection;
+ unsigned char b_InputClockLevel;
+ unsigned char b_OutputLevel;
+ unsigned char b_HardwareGateLevel;
//BEGIN JK 27.10.2003 : Add the possibility to use a 40 Mhz quartz
DWORD dw_Test = 0;
//END JK 27.10.2003 : Add the possibility to use a 40 Mhz quartz
i_ReturnValue = insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_TimerNbr = (BYTE) CR_CHAN(insn->chanspec);
- b_TimerMode = (BYTE) data[0];
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_TimerNbr = (unsigned char) CR_CHAN(insn->chanspec);
+ b_TimerMode = (unsigned char) data[0];
ul_ReloadValue = (ULONG) data[1];
- b_InputClockSelection = (BYTE) data[2];
- b_InputClockLevel = (BYTE) data[3];
- b_OutputLevel = (BYTE) data[4];
- b_HardwareGateLevel = (BYTE) data[5];
+ b_InputClockSelection = (unsigned char) data[2];
+ b_InputClockLevel = (unsigned char) data[3];
+ b_OutputLevel = (unsigned char) data[4];
+ b_HardwareGateLevel = (unsigned char) data[5];
/* Test the module number */
if (b_ModulNbr < 4) {
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnableTimer |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TimerNbr, |
-| BYTE_ b_InterruptEnable)
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TimerNbr, |
+| unsigned char_ b_InterruptEnable)
INT i_APCI1710_InsnWriteEnableDisableTimer(struct comedi_device *dev,struct comedi_subdevice *s,
struct comedi_insn *insn,unsigned int *data) |
+----------------------------------------------------------------------------+
| generate a interrupt after the timer value reach |
| the zero. See function "i_APCI1710_SetBoardIntRoutineX"|
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board |
| APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number |
+| unsigned char_ b_ModulNbr : Selected module number |
| (0 to 3) |
-| BYTE_ b_TimerNbr : Timer number to enable |
+| unsigned char_ b_TimerNbr : Timer number to enable |
| (0 to 2) |
-| BYTE_ b_InterruptEnable : Enable or disable the |
+| unsigned char_ b_InterruptEnable : Enable or disable the |
| timer interrupt. |
| APCI1710_ENABLE : |
| Enable the timer interrupt |
| APCI1710_DISABLE : |
| Disable the timer interrupt|
i_ReturnValue=insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_TimerNbr = (BYTE) CR_CHAN(insn->chanspec);
- b_ActionType = (BYTE) data[0]; // enable disable
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_TimerNbr = (unsigned char) CR_CHAN(insn->chanspec);
+ b_ActionType = (unsigned char) data[0]; // enable disable
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
{
INT i_ReturnValue = 0;
DWORD dw_DummyRead;
- BYTE b_ModulNbr;
- BYTE b_TimerNbr;
- BYTE b_ActionType;
- BYTE b_InterruptEnable;
+ unsigned char b_ModulNbr;
+ unsigned char b_TimerNbr;
+ unsigned char b_ActionType;
+ unsigned char b_InterruptEnable;
i_ReturnValue = insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_TimerNbr = (BYTE) CR_CHAN(insn->chanspec);
- b_ActionType = (BYTE) data[0]; // enable disable
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_TimerNbr = (unsigned char) CR_CHAN(insn->chanspec);
+ b_ActionType = (unsigned char) data[0]; // enable disable
/* Test the module number */
if (b_ModulNbr < 4) {
switch (b_ActionType) {
case APCI1710_ENABLE:
- b_InterruptEnable = (BYTE) data[1];
+ b_InterruptEnable = (unsigned char) data[1];
/* Test the interrupt selection */
if ((b_InterruptEnable == APCI1710_ENABLE) ||
(b_InterruptEnable == APCI1710_DISABLE)) {
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadAllTimerValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
| PULONG_ pul_TimerValueArray)
INT i_APCI1710_InsnReadAllTimerValue(struct comedi_device *dev,struct comedi_subdevice *s,
struct comedi_insn *insn,unsigned int *data) |
| Task : Return the all timer values from selected timer |
| module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board |
| APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number |
+| unsigned char_ b_ModulNbr : Selected module number |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pul_TimerValueArray : Timer value array. |
struct comedi_insn *insn, unsigned int *data)
{
INT i_ReturnValue = 0;
- BYTE b_ModulNbr, b_ReadType;
+ unsigned char b_ModulNbr, b_ReadType;
PULONG pul_TimerValueArray;
b_ModulNbr = CR_AREF(insn->chanspec);
INT i_APCI1710_InsnBitsTimer(struct comedi_device * dev, struct comedi_subdevice * s,
struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_BitsType;
+ unsigned char b_BitsType;
INT i_ReturnValue = 0;
b_BitsType = data[0];
switch (b_BitsType) {
case APCI1710_TIMER_READVALUE:
i_ReturnValue = i_APCI1710_ReadTimerValue(dev,
- (BYTE)CR_AREF(insn->chanspec),
- (BYTE)CR_CHAN(insn->chanspec),
+ (unsigned char)CR_AREF(insn->chanspec),
+ (unsigned char)CR_CHAN(insn->chanspec),
(PULONG) & data[0]);
break;
case APCI1710_TIMER_GETOUTPUTLEVEL:
i_ReturnValue = i_APCI1710_GetTimerOutputLevel(dev,
- (BYTE)CR_AREF(insn->chanspec),
- (BYTE)CR_CHAN(insn->chanspec),
- (PBYTE) &data[0]);
+ (unsigned char)CR_AREF(insn->chanspec),
+ (unsigned char)CR_CHAN(insn->chanspec),
+ (unsigned char *) &data[0]);
break;
case APCI1710_TIMER_GETPROGRESSSTATUS:
i_ReturnValue = i_APCI1710_GetTimerProgressStatus(dev,
- (BYTE)CR_AREF(insn->chanspec),
- (BYTE)CR_CHAN(insn->chanspec),
- (PBYTE)&data[0]);
+ (unsigned char)CR_AREF(insn->chanspec),
+ (unsigned char)CR_CHAN(insn->chanspec),
+ (unsigned char *)&data[0]);
break;
case APCI1710_TIMER_WRITEVALUE:
i_ReturnValue = i_APCI1710_WriteTimerValue(dev,
- (BYTE)CR_AREF(insn->chanspec),
- (BYTE)CR_CHAN(insn->chanspec),
+ (unsigned char)CR_AREF(insn->chanspec),
+ (unsigned char)CR_CHAN(insn->chanspec),
(ULONG)data[1]);
break;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadTimerValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TimerNbr, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TimerNbr, |
| PULONG_ pul_TimerValue) |
+----------------------------------------------------------------------------+
| Task : Return the timer value from selected digital timer |
| (b_TimerNbr) from selected timer module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board |
| APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number |
+| unsigned char_ b_ModulNbr : Selected module number |
| (0 to 3) |
-| BYTE_ b_TimerNbr : Timer number to read |
+| unsigned char_ b_TimerNbr : Timer number to read |
| (0 to 2) |
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pul_TimerValue : Timer value |
*/
INT i_APCI1710_ReadTimerValue(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
PULONG pul_TimerValue)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetTimerOutputLevel |
- | (BYTE_ b_BoardHandle, |
- | BYTE_ b_ModulNbr, |
- | BYTE_ b_TimerNbr, |
- | PBYTE_ pb_OutputLevel) |
+ | (unsigned char_ b_BoardHandle, |
+ | unsigned char_ b_ModulNbr, |
+ | unsigned char_ b_TimerNbr, |
+ | unsigned char *_ pb_OutputLevel) |
+----------------------------------------------------------------------------+
| Task : Return the output signal level (pb_OutputLevel) from |
| selected digital timer (b_TimerNbr) from selected timer|
| module (b_ModulNbr). |
+----------------------------------------------------------------------------+
- | Input Parameters : BYTE_ b_BoardHandle : Handle of board |
+ | Input Parameters : unsigned char_ b_BoardHandle : Handle of board |
| APCI-1710 |
- | BYTE_ b_ModulNbr : Selected module number |
+ | unsigned char_ b_ModulNbr : Selected module number |
| (0 to 3) |
- | BYTE_ b_TimerNbr : Timer number to test |
+ | unsigned char_ b_TimerNbr : Timer number to test |
| (0 to 2) |
+----------------------------------------------------------------------------+
- | Output Parameters : PBYTE_ pb_OutputLevel : Output signal level |
+ | Output Parameters : unsigned char *_ pb_OutputLevel : Output signal level |
| 0 : The output is low |
| 1 : The output is high |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_GetTimerOutputLevel(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
- PBYTE pb_OutputLevel)
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
+ unsigned char * pb_OutputLevel)
{
INT i_ReturnValue = 0;
DWORD dw_TimerStatus;
/* Read the timer status */
dw_TimerStatus = inl(devpriv->s_BoardInfos.ui_Address + 16 + (b_TimerNbr * 4) + (64 * b_ModulNbr));
- *pb_OutputLevel = (BYTE) (((dw_TimerStatus >> 7) & 1) ^ devpriv-> s_ModuleInfo[b_ModulNbr].s_82X54ModuleInfo.s_82X54TimerInfo[b_TimerNbr].b_OutputLevel);
+ *pb_OutputLevel = (unsigned char) (((dw_TimerStatus >> 7) & 1) ^ devpriv-> s_ModuleInfo[b_ModulNbr].s_82X54ModuleInfo.s_82X54TimerInfo[b_TimerNbr].b_OutputLevel);
} else {
/* Timer not initialised see function */
DPRINTK("Timer not initialised see function\n");
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetTimerProgressStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TimerNbr, |
-| PBYTE_ pb_TimerStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TimerNbr, |
+| unsigned char *_ pb_TimerStatus) |
+----------------------------------------------------------------------------+
| Task : Return the progress status (pb_TimerStatus) from |
| selected digital timer (b_TimerNbr) from selected timer|
| module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board |
| APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number |
+| unsigned char_ b_ModulNbr : Selected module number |
| (0 to 3) |
-| BYTE_ b_TimerNbr : Timer number to test |
+| unsigned char_ b_TimerNbr : Timer number to test |
| (0 to 2) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_TimerStatus : Output signal level |
+| Output Parameters : unsigned char *_ pb_TimerStatus : Output signal level |
| 0 : Timer not in progress |
| 1 : Timer in progress |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_GetTimerProgressStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
- PBYTE pb_TimerStatus)
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
+ unsigned char * pb_TimerStatus)
{
INT i_ReturnValue = 0;
DWORD dw_TimerStatus;
/* Read the timer status */
dw_TimerStatus = inl(devpriv->s_BoardInfos.ui_Address + 16 + (b_TimerNbr * 4) + (64 * b_ModulNbr));
- *pb_TimerStatus = (BYTE) ((dw_TimerStatus) >> 8) & 1;
+ *pb_TimerStatus = (unsigned char) ((dw_TimerStatus) >> 8) & 1;
printk("ProgressStatus : %d", *pb_TimerStatus);
} else {
/* Timer not initialised see function */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_WriteTimerValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TimerNbr, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TimerNbr, |
| ULONG_ ul_WriteValue) |
+----------------------------------------------------------------------------+
| Task : Write the value (ul_WriteValue) into the selected timer|
| The action in depend of the time mode selection. |
| See timer mode description table. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board |
| APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number |
+| unsigned char_ b_ModulNbr : Selected module number |
| (0 to 3) |
-| BYTE_ b_TimerNbr : Timer number to write |
+| unsigned char_ b_TimerNbr : Timer number to write |
| (0 to 2) |
| ULONG_ ul_WriteValue : Value to write |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_WriteTimerValue(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
ULONG ul_WriteValue)
{
INT i_ReturnValue = 0;
* 82X54 READ & WRITE FUNCTION
*/
INT i_APCI1710_ReadTimerValue(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
PULONG pul_TimerValue);
INT i_APCI1710_GetTimerOutputLevel(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
- PBYTE pb_OutputLevel);
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
+ unsigned char * pb_OutputLevel);
INT i_APCI1710_GetTimerProgressStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
- PBYTE pb_TimerStatus);
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
+ unsigned char * pb_TimerStatus);
/*
* 82X54 WRITE FUNCTION
*/
INT i_APCI1710_WriteTimerValue(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_TimerNbr,
+ unsigned char b_ModulNbr, unsigned char b_TimerNbr,
ULONG ul_WriteValue);
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitChrono |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_ChronoMode, |
-| BYTE_ b_PCIInputClock, |
-| BYTE_ b_TimingUnit, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_ChronoMode, |
+| unsigned char_ b_PCIInputClock, |
+| unsigned char_ b_TimingUnit, |
| ULONG_ ul_TimingInterval, |
| PULONG_ pul_RealTimingInterval)
| The mode 4 to 7 is appropriate for measuring the timing|
| between two event. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr CR_AREF(insn->chanspec) : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr CR_AREF(insn->chanspec) : Module number to configure |
| (0 to 3) |
-| BYTE_ b_ChronoMode data[0] : Chronometer action mode |
+| unsigned char_ b_ChronoMode data[0] : Chronometer action mode |
| (0 to 7). |
-| BYTE_ b_PCIInputClock data[1] : Selection from PCI bus clock|
+| unsigned char_ b_PCIInputClock data[1] : Selection from PCI bus clock|
| - APCI1710_30MHZ : |
| The PC have a PCI bus |
| clock from 30 MHz |
| The APCI-1710 have a |
| integrated 40Mhz |
| quartz. |
-| BYTE_ b_TimingUnit data[2] : Base timing unity (0 to 4) |
+| unsigned char_ b_TimingUnit data[2] : Base timing unity (0 to 4) |
| 0 : ns |
| 1 : µs |
| 2 : ms |
double d_RealTimingInterval = 0;
DWORD dw_ModeArray[8] =
{ 0x01, 0x05, 0x00, 0x04, 0x02, 0x0E, 0x0A, 0x06 };
- BYTE b_ModulNbr, b_ChronoMode, b_PCIInputClock, b_TimingUnit;
+ unsigned char b_ModulNbr, b_ChronoMode, b_PCIInputClock, b_TimingUnit;
b_ModulNbr = CR_AREF(insn->chanspec);
- b_ChronoMode = (BYTE) data[0];
- b_PCIInputClock = (BYTE) data[1];
- b_TimingUnit = (BYTE) data[2];
+ b_ChronoMode = (unsigned char) data[0];
+ b_PCIInputClock = (unsigned char) data[1];
+ b_TimingUnit = (unsigned char) data[2];
ul_TimingInterval = (ULONG) data[3];
i_ReturnValue = insn->n;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnableChrono |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_CycleMode, |
-| BYTE_ b_InterruptEnable)
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_CycleMode, |
+| unsigned char_ b_InterruptEnable)
INT i_APCI1710_InsnWriteEnableDisableChrono(struct comedi_device *dev,
struct comedi_subdevice *s,struct comedi_insn *insn,unsigned int *data) |
+----------------------------------------------------------------------------+
| witch the " i_APCI1710_EnableChrono" function, if no |
| stop signal occur this start signal is ignored.
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr CR_AREF(chanspec) : Selected module number (0 to 3) |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr CR_AREF(chanspec) : Selected module number (0 to 3) |
data[0] ENABle/Disable chrono
-| BYTE_ b_CycleMode : Selected the chronometer |
+| unsigned char_ b_CycleMode : Selected the chronometer |
| data[1] acquisition mode |
-| BYTE_ b_InterruptEnable : Enable or disable the |
+| unsigned char_ b_InterruptEnable : Enable or disable the |
| data[2] chronometer interrupt. |
| APCI1710_ENABLE: |
| Enable the chronometer |
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
- BYTE b_ModulNbr, b_CycleMode, b_InterruptEnable, b_Action;
+ unsigned char b_ModulNbr, b_CycleMode, b_InterruptEnable, b_Action;
b_ModulNbr = CR_AREF(insn->chanspec);
- b_Action = (BYTE) data[0];
- b_CycleMode = (BYTE) data[1];
- b_InterruptEnable = (BYTE) data[2];
+ b_Action = (unsigned char) data[0];
+ b_CycleMode = (unsigned char) data[1];
+ b_InterruptEnable = (unsigned char) data[2];
i_ReturnValue = insn->n;
/**************************/
INT i_APCI1710_InsnReadChrono(struct comedi_device * dev, struct comedi_subdevice * s,
struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_ReadType;
+ unsigned char b_ReadType;
INT i_ReturnValue = insn->n;
b_ReadType = CR_CHAN(insn->chanspec);
switch (b_ReadType) {
case APCI1710_CHRONO_PROGRESS_STATUS:
i_ReturnValue = i_APCI1710_GetChronoProgressStatus(dev,
- (BYTE) CR_AREF(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_CHRONO_READVALUE:
i_ReturnValue = i_APCI1710_ReadChronoValue(dev,
- (BYTE) CR_AREF(insn->chanspec),
+ (unsigned char) CR_AREF(insn->chanspec),
(UINT) insn->unused[0],
- (PBYTE) & data[0], (PULONG) & data[1]);
+ (unsigned char *) & data[0], (PULONG) & data[1]);
break;
case APCI1710_CHRONO_CONVERTVALUE:
i_ReturnValue = i_APCI1710_ConvertChronoValue(dev,
- (BYTE) CR_AREF(insn->chanspec),
+ (unsigned char) CR_AREF(insn->chanspec),
(ULONG) insn->unused[0],
(PULONG) & data[0],
- (PBYTE) & data[1],
- (PBYTE) & data[2],
+ (unsigned char *) & data[1],
+ (unsigned char *) & data[2],
(PUINT) & data[3],
(PUINT) & data[4], (PUINT) & data[5]);
break;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetChronoProgressStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_ChronoStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_ChronoStatus) |
+----------------------------------------------------------------------------+
| Task : Return the chronometer status (pb_ChronoStatus) from |
| selected chronometer module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pb_ChronoStatus : Return the chronometer |
| status. |
*/
INT i_APCI1710_GetChronoProgressStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_ChronoStatus)
+ unsigned char b_ModulNbr, unsigned char * pb_ChronoStatus)
{
INT i_ReturnValue = 0;
DWORD dw_Status;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadChronoValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
| UINT_ ui_TimeOut, |
-| PBYTE_ pb_ChronoStatus, |
+| unsigned char *_ pb_ChronoStatus, |
| PULONG_ pul_ChronoValue) |
+----------------------------------------------------------------------------+
| Task : Return the chronometer status (pb_ChronoStatus) and the|
| "i_APCI1710_InitChrono" function and the time unity is |
| the b_TimingUnit from "i_APCI1710_InitChrono" function|
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pb_ChronoStatus : Return the chronometer |
| status. |
*/
INT i_APCI1710_ReadChronoValue(struct comedi_device * dev,
- BYTE b_ModulNbr,
- UINT ui_TimeOut, PBYTE pb_ChronoStatus, PULONG pul_ChronoValue)
+ unsigned char b_ModulNbr,
+ UINT ui_TimeOut, unsigned char * pb_ChronoStatus, PULONG pul_ChronoValue)
{
INT i_ReturnValue = 0;
DWORD dw_Status;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ConvertChronoValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
| ULONG_ ul_ChronoValue, |
| PULONG_ pul_Hour, |
-| PBYTE_ pb_Minute, |
-| PBYTE_ pb_Second, |
+| unsigned char *_ pb_Minute, |
+| unsigned char *_ pb_Second, |
| PUINT_ pui_MilliSecond, |
| PUINT_ pui_MicroSecond, |
| PUINT_ pui_NanoSecond) |
| Task : Convert the chronometer measured timing |
| (ul_ChronoValue) in to h, mn, s, ms, µs, ns. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3)|
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3)|
| ULONG_ ul_ChronoValue : Measured chronometer timing |
| value. |
| See"i_APCI1710_ReadChronoValue"|
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pul_Hour : Chronometer timing hour |
-| PBYTE_ pb_Minute : Chronometer timing minute |
-| PBYTE_ pb_Second : Chronometer timing second |
+| unsigned char *_ pb_Minute : Chronometer timing minute |
+| unsigned char *_ pb_Second : Chronometer timing second |
| PUINT_ pui_MilliSecond : Chronometer timing mini |
| second |
| PUINT_ pui_MicroSecond : Chronometer timing micro |
*/
INT i_APCI1710_ConvertChronoValue(struct comedi_device * dev,
- BYTE b_ModulNbr,
+ unsigned char b_ModulNbr,
ULONG ul_ChronoValue,
PULONG pul_Hour,
- PBYTE pb_Minute,
- PBYTE pb_Second,
+ unsigned char * pb_Minute,
+ unsigned char * pb_Second,
PUINT pui_MilliSecond, PUINT pui_MicroSecond, PUINT pui_NanoSecond)
{
INT i_ReturnValue = 0;
d_Minute = d_Hour - *pul_Hour;
d_Minute = d_Minute * 60;
- *pb_Minute = (BYTE) d_Minute;
+ *pb_Minute = (unsigned char) d_Minute;
/************************/
/* Calculate the second */
d_Second = d_Minute - *pb_Minute;
d_Second = d_Second * 60;
- *pb_Second = (BYTE) d_Second;
+ *pb_Second = (unsigned char) d_Second;
/*****************************/
/* Calculate the mini second */
| parameter b_Channel. Setting an output means setting an|
| output high. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3)|
-| BYTE_ b_OutputChannel : Selection from digital output |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3)|
+| unsigned char_ b_OutputChannel : Selection from digital output |
| CR_CHAN() channel (0 to 2) |
| 0 : Channel H |
| 1 : Channel A |
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_SetChronoChlOff |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_OutputChannel) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_OutputChannel) |
+----------------------------------------------------------------------------+
| Task : Resets the output witch has been passed with the |
| parameter b_Channel. Resetting an output means setting |
| an output low. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710
data[0] : Chl ON, Chl OFF , Chl Read , Port Read
-| BYTE_ b_ModulNbr CR_AREF : Selected module number (0 to 3)|
-| BYTE_ b_OutputChannel CR_CHAN : Selection from digital output |
+| unsigned char_ b_ModulNbr CR_AREF : Selected module number (0 to 3)|
+| unsigned char_ b_OutputChannel CR_CHAN : Selection from digital output |
| channel (0 to 2) |
| 0 : Channel H |
| 1 : Channel A |
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadChronoChlValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_InputChannel, |
-| PBYTE_ pb_ChannelStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_InputChannel, |
+| unsigned char *_ pb_ChannelStatus) |
+----------------------------------------------------------------------------+
| Task : Return the status from selected digital input |
| (b_InputChannel) from selected chronometer |
| module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3)|
-| BYTE_ b_InputChannel : Selection from digital input |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3)|
+| unsigned char_ b_InputChannel : Selection from digital input |
| channel (0 to 2) |
| CR_CHAN() 0 : Channel E |
| 1 : Channel F |
| 2 : Channel G |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_ChannelStatus : Digital input channel status.|
+| Output Parameters : unsigned char *_ pb_ChannelStatus : Digital input channel status.|
| data[0] 0 : Channel is not active |
| 1 : Channel is active |
+----------------------------------------------------------------------------+
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadChronoPortValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_PortValue) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_PortValue) |
+----------------------------------------------------------------------------+
| Task : Return the status from digital inputs port from |
| selected (b_ModulNbr) chronometer module. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3)|
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3)|
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_PortValue : Digital inputs port status.
+| Output Parameters : unsigned char *_ pb_PortValue : Digital inputs port status.
| data[0]
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
- BYTE b_ModulNbr, b_OutputChannel, b_InputChannel, b_IOType;
+ unsigned char b_ModulNbr, b_OutputChannel, b_InputChannel, b_IOType;
DWORD dw_Status;
- PBYTE pb_ChannelStatus;
- PBYTE pb_PortValue;
+ unsigned char * pb_ChannelStatus;
+ unsigned char * pb_PortValue;
b_ModulNbr = CR_AREF(insn->chanspec);
i_ReturnValue = insn->n;
- b_IOType = (BYTE) data[0];
+ b_IOType = (unsigned char) data[0];
/**************************/
/* Test the module number */
case APCI1710_CHRONO_SET_CHANNELOFF:
b_OutputChannel =
- (BYTE) CR_CHAN(insn->chanspec);
+ (unsigned char) CR_CHAN(insn->chanspec);
if (b_OutputChannel <= 2) {
outl(0, devpriv->s_BoardInfos.
case APCI1710_CHRONO_SET_CHANNELON:
b_OutputChannel =
- (BYTE) CR_CHAN(insn->chanspec);
+ (unsigned char) CR_CHAN(insn->chanspec);
if (b_OutputChannel <= 2) {
outl(1, devpriv->s_BoardInfos.
/**********************************/
/* Test the digital input channel */
/**********************************/
- pb_ChannelStatus = (PBYTE) & data[0];
+ pb_ChannelStatus = (unsigned char *) & data[0];
b_InputChannel =
- (BYTE) CR_CHAN(insn->chanspec);
+ (unsigned char) CR_CHAN(insn->chanspec);
if (b_InputChannel <= 2) {
(64 * b_ModulNbr));
*pb_ChannelStatus =
- (BYTE) (((dw_Status >>
+ (unsigned char) (((dw_Status >>
b_InputChannel)
& 1) ^ 1);
} // if ((b_InputChannel >= 0) && (b_InputChannel <= 2))
case APCI1710_CHRONO_READ_PORT:
- pb_PortValue = (PBYTE) & data[0];
+ pb_PortValue = (unsigned char *) & data[0];
dw_Status =
inl(devpriv->s_BoardInfos.
(64 * b_ModulNbr));
*pb_PortValue =
- (BYTE) ((dw_Status & 0x7) ^ 7);
+ (unsigned char) ((dw_Status & 0x7) ^ 7);
break;
}
} else {
struct comedi_insn *insn, unsigned int *data);
INT i_APCI1710_GetChronoProgressStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_ChronoStatus);
+ unsigned char b_ModulNbr, unsigned char * pb_ChronoStatus);
INT i_APCI1710_ReadChronoValue(struct comedi_device *dev,
- BYTE b_ModulNbr,
- UINT ui_TimeOut, PBYTE pb_ChronoStatus,
+ unsigned char b_ModulNbr,
+ UINT ui_TimeOut, unsigned char * pb_ChronoStatus,
PULONG pul_ChronoValue);
INT i_APCI1710_ConvertChronoValue(struct comedi_device *dev,
- BYTE b_ModulNbr,
+ unsigned char b_ModulNbr,
ULONG ul_ChronoValue,
PULONG pul_Hour,
- PBYTE pb_Minute,
- PBYTE pb_Second,
+ unsigned char * pb_Minute,
+ unsigned char * pb_Second,
PUINT pui_MilliSecond, PUINT pui_MicroSecond,
PUINT pui_NanoSecond);
| I/O. |
+----------------------------------------------------------------------------+
| Input Parameters : |
-| BYTE_ b_ModulNbr data[0]: Module number to |
+| unsigned char_ b_ModulNbr data[0]: Module number to |
| configure (0 to 3) |
-| BYTE_ b_ChannelAMode data[1] : Channel A mode selection |
+| unsigned char_ b_ChannelAMode data[1] : Channel A mode selection |
| 0 : Channel used for digital |
| input |
| 1 : Channel used for digital |
| output |
-| BYTE_ b_ChannelBMode data[2] : Channel B mode selection |
+| unsigned char_ b_ChannelBMode data[2] : Channel B mode selection |
| 0 : Channel used for digital |
| input |
| 1 : Channel used for digital |
INT i_APCI1710_InsnConfigDigitalIO(struct comedi_device * dev, struct comedi_subdevice * s,
struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_ModulNbr, b_ChannelAMode, b_ChannelBMode;
- BYTE b_MemoryOnOff, b_ConfigType;
+ unsigned char b_ModulNbr, b_ChannelAMode, b_ChannelBMode;
+ unsigned char b_MemoryOnOff, b_ConfigType;
INT i_ReturnValue = 0;
DWORD dw_WriteConfig = 0;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_ConfigType = (BYTE) data[0]; // Memory or Init
- b_ChannelAMode = (BYTE) data[1];
- b_ChannelBMode = (BYTE) data[2];
- b_MemoryOnOff = (BYTE) data[1]; // if memory operation
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_ConfigType = (unsigned char) data[0]; // Memory or Init
+ b_ChannelAMode = (unsigned char) data[1];
+ b_ChannelBMode = (unsigned char) data[2];
+ b_MemoryOnOff = (unsigned char) data[1]; // if memory operation
i_ReturnValue = insn->n;
/**************************/
|
-| BYTE_ b_ModulNbr CR_AREF(chanspec) : Selected module number |
+| unsigned char_ b_ModulNbr CR_AREF(chanspec) : Selected module number |
| (0 to 3) |
-| BYTE_ b_InputChannel CR_CHAN(chanspec) : Selection from digital |
+| unsigned char_ b_InputChannel CR_CHAN(chanspec) : Selection from digital |
| input ( 0 to 6) |
| 0 : Channel C |
| 1 : Channel D |
+----------------------------------------------------------------------------+
*/
-//_INT_ i_APCI1710_ReadDigitalIOChlValue (BYTE_ b_BoardHandle,
-// BYTE_ b_ModulNbr,
-// BYTE_ b_InputChannel,
+//_INT_ i_APCI1710_ReadDigitalIOChlValue (unsigned char_ b_BoardHandle,
+// unsigned char_ b_ModulNbr,
+// unsigned char_ b_InputChannel,
//
-// PBYTE_ pb_ChannelStatus)
+// unsigned char *_ pb_ChannelStatus)
INT i_APCI1710_InsnReadDigitalIOChlValue(struct comedi_device * dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg;
- BYTE b_ModulNbr, b_InputChannel;
- PBYTE pb_ChannelStatus;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_InputChannel = (BYTE) CR_CHAN(insn->chanspec);
+ unsigned char b_ModulNbr, b_InputChannel;
+ unsigned char * pb_ChannelStatus;
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_InputChannel = (unsigned char) CR_CHAN(insn->chanspec);
data[0] = 0;
- pb_ChannelStatus = (PBYTE) & data[0];
+ pb_ChannelStatus = (unsigned char *) & data[0];
i_ReturnValue = insn->n;
/**************************/
(64 * b_ModulNbr));
*pb_ChannelStatus =
- (BYTE) ((dw_StatusReg ^
+ (unsigned char) ((dw_StatusReg ^
0x1C) >>
b_InputChannel) & 1;
| parameter b_Channel. Setting an output means setting |
| an ouput high. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr (aref ) : Selected module number (0 to 3)|
-| BYTE_ b_OutputChannel (CR_CHAN) : Selection from digital output |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr (aref ) : Selected module number (0 to 3)|
+| unsigned char_ b_OutputChannel (CR_CHAN) : Selection from digital output |
| channel (0 to 2) |
| 0 : Channel H |
| 1 : Channel A |
+----------------------------------------------------------------------------+
*/
-//_INT_ i_APCI1710_SetDigitalIOChlOn (BYTE_ b_BoardHandle,
-// BYTE_ b_ModulNbr,
-// BYTE_ b_OutputChannel)
+//_INT_ i_APCI1710_SetDigitalIOChlOn (unsigned char_ b_BoardHandle,
+// unsigned char_ b_ModulNbr,
+// unsigned char_ b_OutputChannel)
INT i_APCI1710_InsnWriteDigitalIOChlOnOff(struct comedi_device * dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
DWORD dw_WriteValue = 0;
- BYTE b_ModulNbr, b_OutputChannel;
+ unsigned char b_ModulNbr, b_OutputChannel;
i_ReturnValue = insn->n;
b_ModulNbr = CR_AREF(insn->chanspec);
b_OutputChannel = CR_CHAN(insn->chanspec);
| from selected digital I/O module (b_ModulNbr)
+----------------------------------------------------------------------------+
| Input Parameters :
- BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr CR_AREF(aref) : Selected module number (0 to 3)|
-| BYTE_ b_PortValue CR_CHAN(chanspec) : Output Value ( 0 To 7 )
+ unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr CR_AREF(aref) : Selected module number (0 to 3)|
+| unsigned char_ b_PortValue CR_CHAN(chanspec) : Output Value ( 0 To 7 )
| data[0] read or write port
data[1] if write then indicate ON or OFF
+----------------------------------------------------------------------------+
*/
-//_INT_ i_APCI1710_SetDigitalIOPortOn (BYTE_ b_BoardHandle,
-// BYTE_ b_ModulNbr,
-// BYTE_ b_PortValue)
+//_INT_ i_APCI1710_SetDigitalIOPortOn (unsigned char_ b_BoardHandle,
+// unsigned char_ b_ModulNbr,
+// unsigned char_ b_PortValue)
INT i_APCI1710_InsnBitsDigitalIOPortOnOff(struct comedi_device * dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
DWORD dw_WriteValue = 0;
DWORD dw_StatusReg;
- BYTE b_ModulNbr, b_PortValue;
- BYTE b_PortOperation, b_PortOnOFF;
+ unsigned char b_ModulNbr, b_PortValue;
+ unsigned char b_PortOperation, b_PortOnOFF;
- PBYTE pb_PortValue;
+ unsigned char * pb_PortValue;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_PortOperation = (BYTE) data[0]; // Input or output
- b_PortOnOFF = (BYTE) data[1]; // if output then On or Off
- b_PortValue = (BYTE) data[2]; // if out put then Value
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_PortOperation = (unsigned char) data[0]; // Input or output
+ b_PortOnOFF = (unsigned char) data[1]; // if output then On or Off
+ b_PortValue = (unsigned char) data[2]; // if out put then Value
i_ReturnValue = insn->n;
- pb_PortValue = (PBYTE) & data[0];
+ pb_PortValue = (unsigned char *) & data[0];
// if input then read value
switch (b_PortOperation) {
inl(devpriv->s_BoardInfos.
ui_Address + (64 * b_ModulNbr));
*pb_PortValue =
- (BYTE) (dw_StatusReg ^ 0x1C);
+ (unsigned char) (dw_StatusReg ^ 0x1C);
} else {
/*******************************/
case APCI1710_INCCPT_INITCOUNTER:
i_ReturnValue = i_APCI1710_InitCounter(dev,
CR_AREF(insn->chanspec),
- (BYTE) data[0],
- (BYTE) data[1],
- (BYTE) data[2], (BYTE) data[3], (BYTE) data[4]);
+ (unsigned char) data[0],
+ (unsigned char) data[1],
+ (unsigned char) data[2], (unsigned char) data[3], (unsigned char) data[4]);
break;
case APCI1710_INCCPT_COUNTERAUTOTEST:
i_ReturnValue = i_APCI1710_CounterAutoTest(dev,
- (PBYTE) & data[0]);
+ (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_INITINDEX:
i_ReturnValue = i_APCI1710_InitIndex(dev,
CR_AREF(insn->chanspec),
- (BYTE) data[0],
- (BYTE) data[1], (BYTE) data[2], (BYTE) data[3]);
+ (unsigned char) data[0],
+ (unsigned char) data[1], (unsigned char) data[2], (unsigned char) data[3]);
break;
case APCI1710_INCCPT_INITREFERENCE:
i_ReturnValue = i_APCI1710_InitReference(dev,
- CR_AREF(insn->chanspec), (BYTE) data[0]);
+ CR_AREF(insn->chanspec), (unsigned char) data[0]);
break;
case APCI1710_INCCPT_INITEXTERNALSTROBE:
i_ReturnValue = i_APCI1710_InitExternalStrobe(dev,
CR_AREF(insn->chanspec),
- (BYTE) data[0], (BYTE) data[1]);
+ (unsigned char) data[0], (unsigned char) data[1]);
break;
case APCI1710_INCCPT_INITCOMPARELOGIC:
case APCI1710_INCCPT_INITFREQUENCYMEASUREMENT:
i_ReturnValue = i_APCI1710_InitFrequencyMeasurement(dev,
CR_AREF(insn->chanspec),
- (BYTE) data[0],
- (BYTE) data[1], (ULONG) data[2], (PULONG) & data[0]);
+ (unsigned char) data[0],
+ (unsigned char) data[1], (ULONG) data[2], (PULONG) & data[0]);
break;
default:
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitCounter |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_CounterRange, |
-| BYTE_ b_FirstCounterModus, |
-| BYTE_ b_FirstCounterOption, |
-| BYTE_ b_SecondCounterModus, |
-| BYTE_ b_SecondCounterOption) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_CounterRange, |
+| unsigned char_ b_FirstCounterModus, |
+| unsigned char_ b_FirstCounterOption, |
+| unsigned char_ b_SecondCounterModus, |
+| unsigned char_ b_SecondCounterOption) |
+----------------------------------------------------------------------------+
| Task : Configure the counter operating mode from selected |
| module (b_ModulNbr). You must calling this function be |
| +----------------------+--------------------+----------------------------+ |
| |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
-| BYTE_ b_CounterRange : Selection form counter |
+| unsigned char_ b_CounterRange : Selection form counter |
| range. |
-| BYTE_ b_FirstCounterModus : First counter operating |
+| unsigned char_ b_FirstCounterModus : First counter operating |
| mode. |
-| BYTE_ b_FirstCounterOption : First counter option. |
-| BYTE_ b_SecondCounterModus : Second counter operating |
+| unsigned char_ b_FirstCounterOption : First counter option. |
+| unsigned char_ b_SecondCounterModus : Second counter operating |
| mode. |
-| BYTE_ b_SecondCounterOption : Second counter option. |
+| unsigned char_ b_SecondCounterOption : Second counter option. |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_InitCounter(struct comedi_device * dev,
- BYTE b_ModulNbr,
- BYTE b_CounterRange,
- BYTE b_FirstCounterModus,
- BYTE b_FirstCounterOption,
- BYTE b_SecondCounterModus, BYTE b_SecondCounterOption)
+ unsigned char b_ModulNbr,
+ unsigned char b_CounterRange,
+ unsigned char b_FirstCounterModus,
+ unsigned char b_FirstCounterOption,
+ unsigned char b_SecondCounterModus, unsigned char b_SecondCounterOption)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_CounterAutoTest |
-| (BYTE_ b_BoardHandle, |
-| PBYTE_ pb_TestStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char *_ pb_TestStatus) |
+----------------------------------------------------------------------------+
| Task : A test mode is intended for testing the component and |
| the connected periphery. All the 8-bit counter chains |
| | 1000 | Error detected of counter 3 | |
| +-----------------+-----------------------------+ |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 | |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 | |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_TestStatus : Auto test conclusion. See table|
+| Output Parameters : unsigned char *_ pb_TestStatus : Auto test conclusion. See table|
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
| -1: The handle parameter of the board is wrong |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_CounterAutoTest(struct comedi_device * dev, PBYTE pb_TestStatus)
+INT i_APCI1710_CounterAutoTest(struct comedi_device * dev, unsigned char * pb_TestStatus)
{
- BYTE b_ModulCpt = 0;
+ unsigned char b_ModulCpt = 0;
INT i_ReturnValue = 0;
DWORD dw_LathchValue;
/*
+----------------------------------------------------------------------------+
-| Function Name : _INT_ i_APCI1710_InitIndex (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_ReferenceAction, |
-| BYTE_ b_IndexOperation, |
-| BYTE_ b_AutoMode, |
-| BYTE_ b_InterruptEnable) |
+| Function Name : _INT_ i_APCI1710_InitIndex (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_ReferenceAction, |
+| unsigned char_ b_IndexOperation, |
+| unsigned char_ b_AutoMode, |
+| unsigned char_ b_InterruptEnable) |
+----------------------------------------------------------------------------+
| Task : Initialise the index corresponding to the selected |
| module (b_ModulNbr). If a INDEX flag occur, you have |
| | | value is cleared (32-Bit) | |
| +------------------------+------------------------------------+ |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_ReferenceAction : Determine if the reference |
+| unsigned char_ b_ReferenceAction : Determine if the reference |
| must set or no for the |
| acceptance from index |
| APCI1710_ENABLE : |
| APCI1710_DISABLE : |
| Reference have not |
| importance |
-| BYTE_ b_IndexOperation : Index operating mode. |
+| unsigned char_ b_IndexOperation : Index operating mode. |
| See table. |
-| BYTE_ b_AutoMode : Enable or disable the |
+| unsigned char_ b_AutoMode : Enable or disable the |
| automatic index reset. |
| APCI1710_ENABLE : |
| Enable the automatic mode |
| APCI1710_DISABLE : |
| Disable the automatic mode |
-| BYTE_ b_InterruptEnable : Enable or disable the |
+| unsigned char_ b_InterruptEnable : Enable or disable the |
| interrupt. |
| APCI1710_ENABLE : |
| Enable the interrupt |
*/
INT i_APCI1710_InitIndex(struct comedi_device * dev,
- BYTE b_ModulNbr,
- BYTE b_ReferenceAction,
- BYTE b_IndexOperation, BYTE b_AutoMode, BYTE b_InterruptEnable)
+ unsigned char b_ModulNbr,
+ unsigned char b_ReferenceAction,
+ unsigned char b_IndexOperation, unsigned char b_AutoMode, unsigned char b_InterruptEnable)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitReference |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_ReferenceLevel) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_ReferenceLevel) |
+----------------------------------------------------------------------------+
| Task : Initialise the reference corresponding to the selected |
| module (b_ModulNbr). |
| | APCI1710_HIGH | Reference occur if "1" | |
| +--------------------+-------------------------+ |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_ReferenceLevel : Reference level. |
+| unsigned char_ b_ReferenceLevel : Reference level. |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_InitReference(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_ReferenceLevel)
+ unsigned char b_ModulNbr, unsigned char b_ReferenceLevel)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitExternalStrobe |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_ExternalStrobe, |
-| BYTE_ b_ExternalStrobeLevel) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_ExternalStrobe, |
+| unsigned char_ b_ExternalStrobeLevel) |
+----------------------------------------------------------------------------+
| Task : Initialises the external strobe level corresponding to |
| the selected module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_ExternalStrobe : External strobe selection |
+| unsigned char_ b_ExternalStrobe : External strobe selection |
| 0 : External strobe A |
| 1 : External strobe B |
-| BYTE_ b_ExternalStrobeLevel : External strobe level |
+| unsigned char_ b_ExternalStrobeLevel : External strobe level |
| APCI1710_LOW : |
| External latch occurs if "0" |
| APCI1710_HIGH : |
*/
INT i_APCI1710_InitExternalStrobe(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_ExternalStrobe, BYTE b_ExternalStrobeLevel)
+ unsigned char b_ModulNbr, unsigned char b_ExternalStrobe, unsigned char b_ExternalStrobeLevel)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitCompareLogic |
- | (BYTE_ b_BoardHandle, |
- | BYTE_ b_ModulNbr, |
+ | (unsigned char_ b_BoardHandle, |
+ | unsigned char_ b_ModulNbr, |
| UINT_ ui_CompareValue) |
+----------------------------------------------------------------------------+
| Task : Set the 32-Bit compare value. At that moment that the |
| incremental counter arrive to the compare value |
| (ui_CompareValue) a interrupt is generated. |
+----------------------------------------------------------------------------+
- | Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
- | BYTE_ b_ModulNbr : Module number to configure |
+ | Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+ | unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
| UINT_ ui_CompareValue : 32-Bit compare value |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_InitCompareLogic(struct comedi_device * dev,
- BYTE b_ModulNbr, UINT ui_CompareValue)
+ unsigned char b_ModulNbr, UINT ui_CompareValue)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitFrequencyMeasurement |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PCIInputClock, |
-| BYTE_ b_TimingUnity, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PCIInputClock, |
+| unsigned char_ b_TimingUnity, |
| ULONG_ ul_TimingInterval, |
| PULONG_ pul_RealTimingInterval) |
+----------------------------------------------------------------------------+
| you call up any other function which gives access to |
| the frequency measurement. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Number of the module to be |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Number of the module to be |
| configured (0 to 3) |
-| BYTE_ b_PCIInputClock : Selection of the PCI bus |
+| unsigned char_ b_PCIInputClock : Selection of the PCI bus |
| clock |
| - APCI1710_30MHZ : |
| The PC has a PCI bus clock |
| - APCI1710_33MHZ : |
| The PC has a PCI bus clock |
| of 33 MHz |
-| BYTE_ b_TimingUnity : Base time unit (0 to 2) |
+| unsigned char_ b_TimingUnity : Base time unit (0 to 2) |
| 0 : ns |
| 1 : æs |
| 2 : ms |
*/
INT i_APCI1710_InitFrequencyMeasurement(struct comedi_device * dev,
- BYTE b_ModulNbr,
- BYTE b_PCIInputClock,
- BYTE b_TimingUnity,
+ unsigned char b_ModulNbr,
+ unsigned char b_PCIInputClock,
+ unsigned char b_TimingUnity,
ULONG ul_TimingInterval, PULONG pul_RealTimingInterval)
{
INT i_ReturnValue = 0;
switch (ui_BitsType) {
case APCI1710_INCCPT_CLEARCOUNTERVALUE:
i_ReturnValue = i_APCI1710_ClearCounterValue(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_CLEARALLCOUNTERVALUE:
case APCI1710_INCCPT_SETINPUTFILTER:
i_ReturnValue = i_APCI1710_SetInputFilter(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (BYTE) data[0], (BYTE) data[1]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char) data[0], (unsigned char) data[1]);
break;
case APCI1710_INCCPT_LATCHCOUNTER:
i_ReturnValue = i_APCI1710_LatchCounter(dev,
- (BYTE) CR_AREF(insn->chanspec), (BYTE) data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char) data[0]);
break;
case APCI1710_INCCPT_SETINDEXANDREFERENCESOURCE:
i_ReturnValue = i_APCI1710_SetIndexAndReferenceSource(dev,
- (BYTE) CR_AREF(insn->chanspec), (BYTE) data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char) data[0]);
break;
case APCI1710_INCCPT_SETDIGITALCHLON:
i_ReturnValue = i_APCI1710_SetDigitalChlOn(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_SETDIGITALCHLOFF:
i_ReturnValue = i_APCI1710_SetDigitalChlOff(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
default:
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ClearCounterValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Clear the counter value from selected module |
| (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_ClearCounterValue(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_ClearCounterValue(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ClearAllCounterValue |
-| (BYTE_ b_BoardHandle) |
+| (unsigned char_ b_BoardHandle) |
+----------------------------------------------------------------------------+
| Task : Clear all counter value. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
INT i_APCI1710_ClearAllCounterValue(struct comedi_device * dev)
{
- BYTE b_ModulCpt = 0;
+ unsigned char b_ModulCpt = 0;
INT i_ReturnValue = 0;
/********************************/
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_SetInputFilter |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_Module, |
-| BYTE_ b_PCIInputClock, |
-| BYTE_ b_Filter) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_Module, |
+| unsigned char_ b_PCIInputClock, |
+| unsigned char_ b_Filter) |
+----------------------------------------------------------------------------+
| Task : Disable or enable the software filter from selected |
| module (b_ModulNbr). b_Filter determine the filter time|
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Number of the module to be |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Number of the module to be |
| configured (0 to 3) |
-| BYTE_ b_PCIInputClock : Selection of the PCI bus |
+| unsigned char_ b_PCIInputClock : Selection of the PCI bus |
| clock |
| - APCI1710_30MHZ : |
| The PC has a PCI bus clock |
| - APCI1710_40MHZ : |
| The APCI1710 has a 40MHz |
| quartz |
-| BYTE_ b_Filter : Filter selection |
+| unsigned char_ b_Filter : Filter selection |
| |
| 30 MHz |
| ------ |
*/
INT i_APCI1710_SetInputFilter(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_PCIInputClock, BYTE b_Filter)
+ unsigned char b_ModulNbr, unsigned char b_PCIInputClock, unsigned char b_Filter)
{
INT i_ReturnValue = 0;
DWORD dw_Status = 0;
/*
+----------------------------------------------------------------------------+
-| Function Name : _INT_ i_APCI1710_LatchCounter (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_LatchReg) |
+| Function Name : _INT_ i_APCI1710_LatchCounter (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_LatchReg) |
+----------------------------------------------------------------------------+
| Task : Latch the courant value from selected module |
| (b_ModulNbr) in to the selected latch register |
| (b_LatchReg). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_LatchReg : Selected latch register |
+| unsigned char_ b_LatchReg : Selected latch register |
| 0 : for the first latch register |
| 1 : for the second latch register |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_LatchCounter(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_LatchReg)
+ unsigned char b_ModulNbr, unsigned char b_LatchReg)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_SetIndexAndReferenceSource |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_SourceSelection) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_SourceSelection) |
+----------------------------------------------------------------------------+
| Task : Determine the hardware source for the index and the |
| reference logic. Per default the index logic is |
| connected to the difference input C and the reference |
| logic is connected to the 24V input E |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_SourceSelection : APCI1710_SOURCE_0 : |
+| unsigned char_ b_SourceSelection : APCI1710_SOURCE_0 : |
| The index logic is connected |
| to the difference input C and|
| the reference logic is |
*/
INT i_APCI1710_SetIndexAndReferenceSource(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_SourceSelection)
+ unsigned char b_ModulNbr, unsigned char b_SourceSelection)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_SetDigitalChlOn |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Sets the digital output H Setting an output means |
| setting an ouput high. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Number of the module to be |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Number of the module to be |
| configured (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_SetDigitalChlOn(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_SetDigitalChlOn(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_SetDigitalChlOff |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Resets the digital output H. Resetting an output means |
| setting an ouput low. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Number of the module to be |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Number of the module to be |
| configured (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_SetDigitalChlOff(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_SetDigitalChlOff(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
switch (ui_WriteType) {
case APCI1710_INCCPT_ENABLELATCHINTERRUPT:
i_ReturnValue = i_APCI1710_EnableLatchInterrupt(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_DISABLELATCHINTERRUPT:
i_ReturnValue = i_APCI1710_DisableLatchInterrupt(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_WRITE16BITCOUNTERVALUE:
i_ReturnValue = i_APCI1710_Write16BitCounterValue(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (BYTE) data[0], (UINT) data[1]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char) data[0], (UINT) data[1]);
break;
case APCI1710_INCCPT_WRITE32BITCOUNTERVALUE:
i_ReturnValue = i_APCI1710_Write32BitCounterValue(dev,
- (BYTE) CR_AREF(insn->chanspec), (ULONG) data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (ULONG) data[0]);
break;
case APCI1710_INCCPT_ENABLEINDEX:
- i_APCI1710_EnableIndex(dev, (BYTE) CR_AREF(insn->chanspec));
+ i_APCI1710_EnableIndex(dev, (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_DISABLEINDEX:
i_ReturnValue = i_APCI1710_DisableIndex(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_ENABLECOMPARELOGIC:
i_ReturnValue = i_APCI1710_EnableCompareLogic(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_DISABLECOMPARELOGIC:
i_ReturnValue = i_APCI1710_DisableCompareLogic(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
case APCI1710_INCCPT_ENABLEFREQUENCYMEASUREMENT:
i_ReturnValue = i_APCI1710_EnableFrequencyMeasurement(dev,
- (BYTE) CR_AREF(insn->chanspec), (BYTE) data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char) data[0]);
break;
case APCI1710_INCCPT_DISABLEFREQUENCYMEASUREMENT:
i_ReturnValue = i_APCI1710_DisableFrequencyMeasurement(dev,
- (BYTE) CR_AREF(insn->chanspec));
+ (unsigned char) CR_AREF(insn->chanspec));
break;
default:
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnableLatchInterrupt |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Enable the latch interrupt from selected module |
| (b_ModulNbr). Each software or hardware latch occur a |
| interrupt. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_EnableLatchInterrupt(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_EnableLatchInterrupt(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_DisableLatchInterrupt |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Disable the latch interrupt from selected module |
| (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_DisableLatchInterrupt(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_DisableLatchInterrupt(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_Write16BitCounterValue |
-| (BYTE_ b_BoardHandle |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_SelectedCounter, |
+| (unsigned char_ b_BoardHandle |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_SelectedCounter, |
| UINT_ ui_WriteValue) |
+----------------------------------------------------------------------------+
| Task : Write a 16-Bit value (ui_WriteValue) in to the selected|
| 16-Bit counter (b_SelectedCounter) from selected module|
| (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_SelectedCounter : Selected 16-Bit counter |
+| unsigned char_ b_SelectedCounter : Selected 16-Bit counter |
| (0 or 1) |
| UINT_ ui_WriteValue : 16-Bit write value |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_Write16BitCounterValue(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_SelectedCounter, UINT ui_WriteValue)
+ unsigned char b_ModulNbr, unsigned char b_SelectedCounter, UINT ui_WriteValue)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_Write32BitCounterValue |
-| (BYTE_ b_BoardHandle |
-| BYTE_ b_ModulNbr, |
+| (unsigned char_ b_BoardHandle |
+| unsigned char_ b_ModulNbr, |
| ULONG_ ul_WriteValue) |
+----------------------------------------------------------------------------+
| Task : Write a 32-Bit value (ui_WriteValue) in to the selected|
| module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
| ULONG_ ul_WriteValue : 32-Bit write value |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_Write32BitCounterValue(struct comedi_device * dev,
- BYTE b_ModulNbr, ULONG ul_WriteValue)
+ unsigned char b_ModulNbr, ULONG ul_WriteValue)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
-| Function Name : _INT_ i_APCI1710_EnableIndex (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| Function Name : _INT_ i_APCI1710_EnableIndex (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Enable the INDEX actions |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_EnableIndex(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_EnableIndex(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
ULONG ul_InterruptLatchReg;
/*
+----------------------------------------------------------------------------+
-| Function Name : _INT_ i_APCI1710_DisableIndex (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| Function Name : _INT_ i_APCI1710_DisableIndex (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Disable the INDEX actions |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_DisableIndex(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_DisableIndex(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnableCompareLogic |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Enable the 32-Bit compare logic. At that moment that |
| the incremental counter arrive to the compare value a |
| interrupt is generated. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : -
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_EnableCompareLogic(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_EnableCompareLogic(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_DisableCompareLogic |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Disable the 32-Bit compare logic.
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : -
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_DisableCompareLogic(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_DisableCompareLogic(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnableFrequencyMeasurement |
- | (BYTE_ b_BoardHandle, |
- | BYTE_ b_ModulNbr, |
- | BYTE_ b_InterruptEnable) |
+ | (unsigned char_ b_BoardHandle, |
+ | unsigned char_ b_ModulNbr, |
+ | unsigned char_ b_InterruptEnable) |
+----------------------------------------------------------------------------+
| Task : Enables the frequency measurement function |
+----------------------------------------------------------------------------+
- | Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
- | BYTE_ b_ModulNbr : Number of the module to be |
+ | Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+ | unsigned char_ b_ModulNbr : Number of the module to be |
| configured (0 to 3) |
- | BYTE_ b_InterruptEnable: Enable or disable the |
+ | unsigned char_ b_InterruptEnable: Enable or disable the |
| interrupt. |
| APCI1710_ENABLE: |
| Enable the interrupt |
*/
INT i_APCI1710_EnableFrequencyMeasurement(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_InterruptEnable)
+ unsigned char b_ModulNbr, unsigned char b_InterruptEnable)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_DisableFrequencyMeasurement |
- | (BYTE_ b_BoardHandle, |
- | BYTE_ b_ModulNbr) |
+ | (unsigned char_ b_BoardHandle, |
+ | unsigned char_ b_ModulNbr) |
+----------------------------------------------------------------------------+
| Task : Disables the frequency measurement function |
+----------------------------------------------------------------------------+
- | Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
- | BYTE_ b_ModulNbr : Number of the module to be |
+ | Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+ | unsigned char_ b_ModulNbr : Number of the module to be |
| configured (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_DisableFrequencyMeasurement(struct comedi_device * dev, BYTE b_ModulNbr)
+INT i_APCI1710_DisableFrequencyMeasurement(struct comedi_device * dev, unsigned char b_ModulNbr)
{
INT i_ReturnValue = 0;
switch (ui_ReadType) {
case APCI1710_INCCPT_READLATCHREGISTERSTATUS:
i_ReturnValue = i_APCI1710_ReadLatchRegisterStatus(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (BYTE) CR_RANGE(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char) CR_RANGE(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_READLATCHREGISTERVALUE:
i_ReturnValue = i_APCI1710_ReadLatchRegisterValue(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (BYTE) CR_RANGE(insn->chanspec), (PULONG) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char) CR_RANGE(insn->chanspec), (PULONG) & data[0]);
printk("Latch Register Value %d\n", data[0]);
break;
case APCI1710_INCCPT_READ16BITCOUNTERVALUE:
i_ReturnValue = i_APCI1710_Read16BitCounterValue(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (BYTE) CR_RANGE(insn->chanspec), (PUINT) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char) CR_RANGE(insn->chanspec), (PUINT) & data[0]);
break;
case APCI1710_INCCPT_READ32BITCOUNTERVALUE:
i_ReturnValue = i_APCI1710_Read32BitCounterValue(dev,
- (BYTE) CR_AREF(insn->chanspec), (PULONG) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (PULONG) & data[0]);
break;
case APCI1710_INCCPT_GETINDEXSTATUS:
i_ReturnValue = i_APCI1710_GetIndexStatus(dev,
- (BYTE) CR_AREF(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_GETREFERENCESTATUS:
i_ReturnValue = i_APCI1710_GetReferenceStatus(dev,
- (BYTE) CR_AREF(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_GETUASSTATUS:
i_ReturnValue = i_APCI1710_GetUASStatus(dev,
- (BYTE) CR_AREF(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_GETCBSTATUS:
i_ReturnValue = i_APCI1710_GetCBStatus(dev,
- (BYTE) CR_AREF(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_GET16BITCBSTATUS:
i_ReturnValue = i_APCI1710_Get16BitCBStatus(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (PBYTE) & data[0], (PBYTE) & data[1]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char *) & data[0], (unsigned char *) & data[1]);
break;
case APCI1710_INCCPT_GETUDSTATUS:
i_ReturnValue = i_APCI1710_GetUDStatus(dev,
- (BYTE) CR_AREF(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_GETINTERRUPTUDLATCHEDSTATUS:
i_ReturnValue = i_APCI1710_GetInterruptUDLatchedStatus(dev,
- (BYTE) CR_AREF(insn->chanspec), (PBYTE) & data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char *) & data[0]);
break;
case APCI1710_INCCPT_READFREQUENCYMEASUREMENT:
i_ReturnValue = i_APCI1710_ReadFrequencyMeasurement(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (PBYTE) & data[0],
- (PBYTE) & data[1], (PULONG) & data[2]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char *) & data[0],
+ (unsigned char *) & data[1], (PULONG) & data[2]);
break;
case APCI1710_INCCPT_READINTERRUPT:
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadLatchRegisterStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_LatchReg, |
-| PBYTE_ pb_LatchStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_LatchReg, |
+| unsigned char *_ pb_LatchStatus) |
+----------------------------------------------------------------------------+
| Task : Read the latch register status from selected module |
| (b_ModulNbr) and selected latch register (b_LatchReg). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_LatchReg : Selected latch register |
+| unsigned char_ b_LatchReg : Selected latch register |
| 0 : for the first latch register |
| 1 : for the second latch register |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_LatchStatus : Latch register status. |
+| Output Parameters : unsigned char *_ pb_LatchStatus : Latch register status. |
| 0 : No latch occur |
| 1 : A software latch occur |
| 2 : A hardware latch occur |
*/
INT i_APCI1710_ReadLatchRegisterStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_LatchReg, PBYTE pb_LatchStatus)
+ unsigned char b_ModulNbr, unsigned char b_LatchReg, unsigned char * pb_LatchStatus)
{
INT i_ReturnValue = 0;
DWORD dw_LatchReg;
ui_Address + (64 * b_ModulNbr));
*pb_LatchStatus =
- (BYTE) ((dw_LatchReg >> (b_LatchReg *
+ (unsigned char) ((dw_LatchReg >> (b_LatchReg *
4)) & 0x3);
} else {
/**************************************************/
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadLatchRegisterValue |
-| (BYTE_ b_BoardHandle,|
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_LatchReg, |
+| (unsigned char_ b_BoardHandle,|
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_LatchReg, |
| PULONG_ pul_LatchValue) |
+----------------------------------------------------------------------------+
| Task : Read the latch register value from selected module |
| (b_ModulNbr) and selected latch register (b_LatchReg). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_LatchReg : Selected latch register |
+| unsigned char_ b_LatchReg : Selected latch register |
| 0 : for the first latch register |
| 1 : for the second latch register |
+----------------------------------------------------------------------------+
*/
INT i_APCI1710_ReadLatchRegisterValue(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_LatchReg, PULONG pul_LatchValue)
+ unsigned char b_ModulNbr, unsigned char b_LatchReg, PULONG pul_LatchValue)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_Read16BitCounterValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_SelectedCounter, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_SelectedCounter, |
| PUINT_ pui_CounterValue) |
+----------------------------------------------------------------------------+
| Task : Latch the selected 16-Bit counter (b_SelectedCounter) |
| from selected module (b_ModulNbr) in to the first |
| latch register and return the latched value. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| BYTE_ b_SelectedCounter : Selected 16-Bit counter |
+| unsigned char_ b_SelectedCounter : Selected 16-Bit counter |
| (0 or 1) |
+----------------------------------------------------------------------------+
| Output Parameters : PUINT_ pui_CounterValue : 16-Bit counter value |
*/
INT i_APCI1710_Read16BitCounterValue(struct comedi_device * dev,
- BYTE b_ModulNbr, BYTE b_SelectedCounter, PUINT pui_CounterValue)
+ unsigned char b_ModulNbr, unsigned char b_SelectedCounter, PUINT pui_CounterValue)
{
INT i_ReturnValue = 0;
DWORD dw_LathchValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_Read32BitCounterValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
| PULONG_ pul_CounterValue) |
+----------------------------------------------------------------------------+
| Task : Latch the 32-Bit counter from selected module |
| (b_ModulNbr) in to the first latch register and return |
| the latched value. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pul_CounterValue : 32-Bit counter value |
*/
INT i_APCI1710_Read32BitCounterValue(struct comedi_device * dev,
- BYTE b_ModulNbr, PULONG pul_CounterValue)
+ unsigned char b_ModulNbr, PULONG pul_CounterValue)
{
INT i_ReturnValue = 0;
/*
+----------------------------------------------------------------------------+
-| Function Name : _INT_ i_APCI1710_GetIndexStatus (BYTE_ b_BoardHandle,|
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_IndexStatus)|
+| Function Name : _INT_ i_APCI1710_GetIndexStatus (unsigned char_ b_BoardHandle,|
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_IndexStatus)|
+----------------------------------------------------------------------------+
| Task : Return the index status |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_IndexStatus : 0 : No INDEX occur |
+| Output Parameters : unsigned char *_ pb_IndexStatus : 0 : No INDEX occur |
| 1 : A INDEX occur |
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
*/
INT i_APCI1710_GetIndexStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_IndexStatus)
+ unsigned char b_ModulNbr, unsigned char * pb_IndexStatus)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
dw_StatusReg = inl(devpriv->s_BoardInfos.
ui_Address + 12 + (64 * b_ModulNbr));
- *pb_IndexStatus = (BYTE) (dw_StatusReg & 1);
+ *pb_IndexStatus = (unsigned char) (dw_StatusReg & 1);
} else {
/*************************************************************/
/* Index not initialised see function "i_APCI1710_InitIndex" */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetReferenceStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_ReferenceStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_ReferenceStatus) |
+----------------------------------------------------------------------------+
| Task : Return the reference status |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_ReferenceStatus : 0 : No REFERENCE occur |
+| Output Parameters : unsigned char *_ pb_ReferenceStatus : 0 : No REFERENCE occur |
| 1 : A REFERENCE occur |
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
*/
INT i_APCI1710_GetReferenceStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_ReferenceStatus)
+ unsigned char b_ModulNbr, unsigned char * pb_ReferenceStatus)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
ui_Address + 24 + (64 * b_ModulNbr));
*pb_ReferenceStatus =
- (BYTE) (~dw_StatusReg & 1);
+ (unsigned char) (~dw_StatusReg & 1);
} else {
/*********************************************************************/
/* Reference not initialised see function "i_APCI1710_InitReference" */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetUASStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_UASStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_UASStatus) |
+----------------------------------------------------------------------------+
| Task : Return the error signal (UAS) status |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_UASStatus : 0 : UAS is low "0" |
+| Output Parameters : unsigned char *_ pb_UASStatus : 0 : UAS is low "0" |
| 1 : UAS is high "1" |
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
*/
INT i_APCI1710_GetUASStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_UASStatus)
+ unsigned char b_ModulNbr, unsigned char * pb_UASStatus)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
dw_StatusReg = inl(devpriv->s_BoardInfos.
ui_Address + 24 + (64 * b_ModulNbr));
- *pb_UASStatus = (BYTE) ((dw_StatusReg >> 1) & 1);
+ *pb_UASStatus = (unsigned char) ((dw_StatusReg >> 1) & 1);
} else {
/****************************************/
/* Counter not initialised see function */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetCBStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_CBStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_CBStatus) |
+----------------------------------------------------------------------------+
| Task : Return the counter overflow status |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_CBStatus : 0 : Counter no overflow |
+| Output Parameters : unsigned char *_ pb_CBStatus : 0 : Counter no overflow |
| 1 : Counter overflow |
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
*/
INT i_APCI1710_GetCBStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_CBStatus)
+ unsigned char b_ModulNbr, unsigned char * pb_CBStatus)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
dw_StatusReg = inl(devpriv->s_BoardInfos.
ui_Address + 16 + (64 * b_ModulNbr));
- *pb_CBStatus = (BYTE) (dw_StatusReg & 1);
+ *pb_CBStatus = (unsigned char) (dw_StatusReg & 1);
} else {
/****************************************/
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_Get16BitCBStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_CBStatusCounter0, |
-| PBYTE_ pb_CBStatusCounter1) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_CBStatusCounter0, |
+| unsigned char *_ pb_CBStatusCounter1) |
+----------------------------------------------------------------------------+
| Task : Returns the counter overflow (counter initialised to |
| 2*16-bit) status from selected incremental counter |
| module |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_CBStatusCounter0 : 0 : No overflow occur for |
+| Output Parameters : unsigned char *_ pb_CBStatusCounter0 : 0 : No overflow occur for |
| the first 16-bit |
| counter |
| 1 : Overflow occur for the|
| first 16-bit counter |
-| PBYTE_ pb_CBStatusCounter1 : 0 : No overflow occur for |
+| unsigned char *_ pb_CBStatusCounter1 : 0 : No overflow occur for |
| the second 16-bit |
| counter |
| 1 : Overflow occur for the|
*/
INT i_APCI1710_Get16BitCBStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_CBStatusCounter0, PBYTE pb_CBStatusCounter1)
+ unsigned char b_ModulNbr, unsigned char * pb_CBStatusCounter0, unsigned char * pb_CBStatusCounter1)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
(64 * b_ModulNbr));
*pb_CBStatusCounter1 =
- (BYTE) ((dw_StatusReg >> 0) &
+ (unsigned char) ((dw_StatusReg >> 0) &
1);
*pb_CBStatusCounter0 =
- (BYTE) ((dw_StatusReg >> 1) &
+ (unsigned char) ((dw_StatusReg >> 1) &
1);
} // if ((ps_APCI1710Variable->s_Board [b_BoardHandle].s_BoardInfos.dw_MolduleConfiguration [b_ModulNbr] & 0xFFFF) >= 0x3136)
else {
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetUDStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_UDStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_UDStatus) |
+----------------------------------------------------------------------------+
| Task : Return the counter progress status |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_UDStatus : 0 : Counter progress in the |
+| Output Parameters : unsigned char *_ pb_UDStatus : 0 : Counter progress in the |
| selected mode down |
| 1 : Counter progress in the |
| selected mode up |
*/
INT i_APCI1710_GetUDStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_UDStatus)
+ unsigned char b_ModulNbr, unsigned char * pb_UDStatus)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
dw_StatusReg = inl(devpriv->s_BoardInfos.
ui_Address + 24 + (64 * b_ModulNbr));
- *pb_UDStatus = (BYTE) ((dw_StatusReg >> 2) & 1);
+ *pb_UDStatus = (unsigned char) ((dw_StatusReg >> 2) & 1);
} else {
/****************************************/
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetInterruptUDLatchedStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| PBYTE_ pb_UDStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char *_ pb_UDStatus) |
+----------------------------------------------------------------------------+
| Task : Return the counter progress latched status after a |
| index interrupt occur. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_UDStatus : 0 : Counter progress in the |
+| Output Parameters : unsigned char *_ pb_UDStatus : 0 : Counter progress in the |
| selected mode down |
| 1 : Counter progress in the |
| selected mode up |
*/
INT i_APCI1710_GetInterruptUDLatchedStatus(struct comedi_device * dev,
- BYTE b_ModulNbr, PBYTE pb_UDStatus)
+ unsigned char b_ModulNbr, unsigned char * pb_UDStatus)
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
dw_StatusReg = inl(devpriv->s_BoardInfos.
ui_Address + 12 + (64 * b_ModulNbr));
- *pb_UDStatus = (BYTE) ((dw_StatusReg >> 1) & 1);
+ *pb_UDStatus = (unsigned char) ((dw_StatusReg >> 1) & 1);
} else {
/****************************/
/* No index interrupt occur */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadFrequencyMeasurement |
- | (BYTE_ b_BoardHandle, |
- | BYTE_ b_ModulNbr, |
- | PBYTE_ pb_Status, |
+ | (unsigned char_ b_BoardHandle, |
+ | unsigned char_ b_ModulNbr, |
+ | unsigned char *_ pb_Status, |
| PULONG_ pul_ReadValue) |
+----------------------------------------------------------------------------+
| Task : Returns the status (pb_Status) and the number of |
| increments in the set time. |
| See function " i_APCI1710_InitFrequencyMeasurement " |
+----------------------------------------------------------------------------+
- | Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
- | BYTE_ b_ModulNbr : Number of the module to be |
+ | Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+ | unsigned char_ b_ModulNbr : Number of the module to be |
| configured (0 to 3) |
+----------------------------------------------------------------------------+
- | Output Parameters : PBYTE_ pb_Status : Returns the frequency |
+ | Output Parameters : unsigned char *_ pb_Status : Returns the frequency |
| measurement status |
| 0 : Counting cycle not |
| started. |
| 2 : Counting cycle stopped. |
| The measurement cycle is |
| completed. |
- | PBYTE_ pb_UDStatus : 0 : Counter progress in the |
+ | unsigned char *_ pb_UDStatus : 0 : Counter progress in the |
| selected mode down |
| 1 : Counter progress in the |
| selected mode up |
*/
INT i_APCI1710_ReadFrequencyMeasurement(struct comedi_device * dev,
- BYTE b_ModulNbr,
- PBYTE pb_Status, PBYTE pb_UDStatus, PULONG pul_ReadValue)
+ unsigned char b_ModulNbr,
+ unsigned char * pb_Status, unsigned char * pb_UDStatus, PULONG pul_ReadValue)
{
INT i_ReturnValue = 0;
UINT ui_16BitValue;
if (dw_StatusReg & 1) {
*pb_Status = 2;
*pb_UDStatus =
- (BYTE) ((dw_StatusReg >>
+ (unsigned char) ((dw_StatusReg >>
1) & 3);
/******************/
/* INSN CONFIG */
INT i_APCI1710_InitCounter(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_CounterRange,
- BYTE b_FirstCounterModus,
- BYTE b_FirstCounterOption,
- BYTE b_SecondCounterModus,
- BYTE b_SecondCounterOption);
+ unsigned char b_ModulNbr,
+ unsigned char b_CounterRange,
+ unsigned char b_FirstCounterModus,
+ unsigned char b_FirstCounterOption,
+ unsigned char b_SecondCounterModus,
+ unsigned char b_SecondCounterOption);
-INT i_APCI1710_CounterAutoTest(struct comedi_device *dev, PBYTE pb_TestStatus);
+INT i_APCI1710_CounterAutoTest(struct comedi_device *dev, unsigned char * pb_TestStatus);
INT i_APCI1710_InitIndex(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_ReferenceAction,
- BYTE b_IndexOperation, BYTE b_AutoMode,
- BYTE b_InterruptEnable);
+ unsigned char b_ModulNbr,
+ unsigned char b_ReferenceAction,
+ unsigned char b_IndexOperation, unsigned char b_AutoMode,
+ unsigned char b_InterruptEnable);
INT i_APCI1710_InitReference(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_ReferenceLevel);
+ unsigned char b_ModulNbr, unsigned char b_ReferenceLevel);
INT i_APCI1710_InitExternalStrobe(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_ExternalStrobe,
- BYTE b_ExternalStrobeLevel);
+ unsigned char b_ModulNbr, unsigned char b_ExternalStrobe,
+ unsigned char b_ExternalStrobeLevel);
INT i_APCI1710_InitCompareLogic(struct comedi_device *dev,
- BYTE b_ModulNbr, UINT ui_CompareValue);
+ unsigned char b_ModulNbr, UINT ui_CompareValue);
INT i_APCI1710_InitFrequencyMeasurement(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_PCIInputClock,
- BYTE b_TimingUnity,
+ unsigned char b_ModulNbr,
+ unsigned char b_PCIInputClock,
+ unsigned char b_TimingUnity,
ULONG ul_TimingInterval,
PULONG pul_RealTimingInterval);
/* INSN BITS */
-INT i_APCI1710_ClearCounterValue(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_ClearCounterValue(struct comedi_device *dev, unsigned char b_ModulNbr);
INT i_APCI1710_ClearAllCounterValue(struct comedi_device *dev);
INT i_APCI1710_SetInputFilter(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_PCIInputClock,
- BYTE b_Filter);
+ unsigned char b_ModulNbr, unsigned char b_PCIInputClock,
+ unsigned char b_Filter);
INT i_APCI1710_LatchCounter(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_LatchReg);
+ unsigned char b_ModulNbr, unsigned char b_LatchReg);
INT i_APCI1710_SetIndexAndReferenceSource(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_SourceSelection);
+ unsigned char b_ModulNbr,
+ unsigned char b_SourceSelection);
-INT i_APCI1710_SetDigitalChlOn(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_SetDigitalChlOn(struct comedi_device *dev, unsigned char b_ModulNbr);
-INT i_APCI1710_SetDigitalChlOff(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_SetDigitalChlOff(struct comedi_device *dev, unsigned char b_ModulNbr);
/* INSN WRITE */
-INT i_APCI1710_EnableLatchInterrupt(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_EnableLatchInterrupt(struct comedi_device *dev, unsigned char b_ModulNbr);
-INT i_APCI1710_DisableLatchInterrupt(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_DisableLatchInterrupt(struct comedi_device *dev, unsigned char b_ModulNbr);
INT i_APCI1710_Write16BitCounterValue(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_SelectedCounter,
+ unsigned char b_ModulNbr, unsigned char b_SelectedCounter,
UINT ui_WriteValue);
INT i_APCI1710_Write32BitCounterValue(struct comedi_device *dev,
- BYTE b_ModulNbr, ULONG ul_WriteValue);
+ unsigned char b_ModulNbr, ULONG ul_WriteValue);
-INT i_APCI1710_EnableIndex(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_EnableIndex(struct comedi_device *dev, unsigned char b_ModulNbr);
-INT i_APCI1710_DisableIndex(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_DisableIndex(struct comedi_device *dev, unsigned char b_ModulNbr);
-INT i_APCI1710_EnableCompareLogic(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_EnableCompareLogic(struct comedi_device *dev, unsigned char b_ModulNbr);
-INT i_APCI1710_DisableCompareLogic(struct comedi_device *dev, BYTE b_ModulNbr);
+INT i_APCI1710_DisableCompareLogic(struct comedi_device *dev, unsigned char b_ModulNbr);
INT i_APCI1710_EnableFrequencyMeasurement(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_InterruptEnable);
+ unsigned char b_ModulNbr,
+ unsigned char b_InterruptEnable);
INT i_APCI1710_DisableFrequencyMeasurement(struct comedi_device *dev,
- BYTE b_ModulNbr);
+ unsigned char b_ModulNbr);
/* INSN READ */
INT i_APCI1710_ReadLatchRegisterStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_LatchReg,
- PBYTE pb_LatchStatus);
+ unsigned char b_ModulNbr, unsigned char b_LatchReg,
+ unsigned char * pb_LatchStatus);
INT i_APCI1710_ReadLatchRegisterValue(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_LatchReg,
+ unsigned char b_ModulNbr, unsigned char b_LatchReg,
PULONG pul_LatchValue);
INT i_APCI1710_Read16BitCounterValue(struct comedi_device *dev,
- BYTE b_ModulNbr, BYTE b_SelectedCounter,
+ unsigned char b_ModulNbr, unsigned char b_SelectedCounter,
PUINT pui_CounterValue);
INT i_APCI1710_Read32BitCounterValue(struct comedi_device *dev,
- BYTE b_ModulNbr, PULONG pul_CounterValue);
+ unsigned char b_ModulNbr, PULONG pul_CounterValue);
INT i_APCI1710_GetIndexStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_IndexStatus);
+ unsigned char b_ModulNbr, unsigned char * pb_IndexStatus);
INT i_APCI1710_GetReferenceStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_ReferenceStatus);
+ unsigned char b_ModulNbr, unsigned char * pb_ReferenceStatus);
INT i_APCI1710_GetUASStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_UASStatus);
+ unsigned char b_ModulNbr, unsigned char * pb_UASStatus);
INT i_APCI1710_GetCBStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_CBStatus);
+ unsigned char b_ModulNbr, unsigned char * pb_CBStatus);
INT i_APCI1710_Get16BitCBStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_CBStatusCounter0,
- PBYTE pb_CBStatusCounter1);
+ unsigned char b_ModulNbr, unsigned char * pb_CBStatusCounter0,
+ unsigned char * pb_CBStatusCounter1);
INT i_APCI1710_GetUDStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_UDStatus);
+ unsigned char b_ModulNbr, unsigned char * pb_UDStatus);
INT i_APCI1710_GetInterruptUDLatchedStatus(struct comedi_device *dev,
- BYTE b_ModulNbr, PBYTE pb_UDStatus);
+ unsigned char b_ModulNbr, unsigned char * pb_UDStatus);
INT i_APCI1710_ReadFrequencyMeasurement(struct comedi_device *dev,
- BYTE b_ModulNbr,
- PBYTE pb_Status, PBYTE pb_UDStatus,
+ unsigned char b_ModulNbr,
+ unsigned char * pb_Status, unsigned char * pb_UDStatus,
PULONG pul_ReadValue);
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitPulseEncoder |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PulseEncoderNbr, |
-| BYTE_ b_InputLevelSelection, |
-| BYTE_ b_TriggerOutputAction, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PulseEncoderNbr, |
+| unsigned char_ b_InputLevelSelection, |
+| unsigned char_ b_TriggerOutputAction, |
| ULONG_ ul_StartValue) |
+----------------------------------------------------------------------------+
| Task : Configure the pulse encoder operating mode selected via|
| You must calling this function be for you call any |
| other function witch access of pulse encoders. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
-| BYTE_ b_PulseEncoderNbr : Pulse encoder selection |
+| unsigned char_ b_PulseEncoderNbr : Pulse encoder selection |
| (0 to 3) |
-| BYTE_ b_InputLevelSelection : Input level selection |
+| unsigned char_ b_InputLevelSelection : Input level selection |
| (0 or 1) |
| 0 : Set pulse encoder|
| count the the low|
| 1 : Set pulse encoder|
| count the the |
| high level pulse.|
-| BYTE_ b_TriggerOutputAction : Digital TRIGGER output |
+| unsigned char_ b_TriggerOutputAction : Digital TRIGGER output |
| action |
| 0 : No action |
| 1 : Set the trigger |
| encoder |
| ULONG_ ul_StartValue : Pulse encoder start value|
| (1 to 4294967295)
- b_ModulNbr =(BYTE) CR_AREF(insn->chanspec);
- b_PulseEncoderNbr =(BYTE) data[0];
- b_InputLevelSelection =(BYTE) data[1];
- b_TriggerOutputAction =(BYTE) data[2];
+ b_ModulNbr =(unsigned char) CR_AREF(insn->chanspec);
+ b_PulseEncoderNbr =(unsigned char) data[0];
+ b_InputLevelSelection =(unsigned char) data[1];
+ b_TriggerOutputAction =(unsigned char) data[2];
ul_StartValue =(ULONG) data[3];
|
+----------------------------------------------------------------------------+
INT i_ReturnValue = 0;
DWORD dw_IntRegister;
- BYTE b_ModulNbr;
- BYTE b_PulseEncoderNbr;
- BYTE b_InputLevelSelection;
- BYTE b_TriggerOutputAction;
+ unsigned char b_ModulNbr;
+ unsigned char b_PulseEncoderNbr;
+ unsigned char b_InputLevelSelection;
+ unsigned char b_TriggerOutputAction;
ULONG ul_StartValue;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_PulseEncoderNbr = (BYTE) data[0];
- b_InputLevelSelection = (BYTE) data[1];
- b_TriggerOutputAction = (BYTE) data[2];
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_PulseEncoderNbr = (unsigned char) data[0];
+ b_InputLevelSelection = (unsigned char) data[1];
+ b_TriggerOutputAction = (unsigned char) data[2];
ul_StartValue = (ULONG) data[3];
i_ReturnValue = insn->n;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnablePulseEncoder |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PulseEncoderNbr, |
-| BYTE_ b_CycleSelection, |
-| BYTE_ b_InterruptHandling) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PulseEncoderNbr, |
+| unsigned char_ b_CycleSelection, |
+| unsigned char_ b_InterruptHandling) |
+----------------------------------------------------------------------------+
| Task : Enableor disable the selected pulse encoder (b_PulseEncoderNbr) |
| from selected module (b_ModulNbr). Each input pulse |
| interrupt is generated when the pulse encoder has run |
| down. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
-| BYTE_ b_PulseEncoderNbr : Pulse encoder selection |
+| unsigned char_ b_PulseEncoderNbr : Pulse encoder selection |
| (0 to 3) |
-| BYTE_ b_CycleSelection : APCI1710_CONTINUOUS: |
+| unsigned char_ b_CycleSelection : APCI1710_CONTINUOUS: |
| Each time the |
| counting value is set|
| on "0", the pulse |
| If the counter is set|
| on "0", the pulse |
| encoder is stopped. |
-| BYTE_ b_InterruptHandling : Interrupts can be |
+| unsigned char_ b_InterruptHandling : Interrupts can be |
| generated, when the pulse|
| encoder has run down. |
| With this parameter the |
| APCI1710_DISABLE: |
| Interrupts are disabled
- b_ModulNbr =(BYTE) CR_AREF(insn->chanspec);
- b_Action =(BYTE) data[0];
- b_PulseEncoderNbr =(BYTE) data[1];
- b_CycleSelection =(BYTE) data[2];
- b_InterruptHandling =(BYTE) data[3];|
+ b_ModulNbr =(unsigned char) CR_AREF(insn->chanspec);
+ b_Action =(unsigned char) data[0];
+ b_PulseEncoderNbr =(unsigned char) data[1];
+ b_CycleSelection =(unsigned char) data[2];
+ b_InterruptHandling =(unsigned char) data[3];|
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
- BYTE b_ModulNbr;
- BYTE b_PulseEncoderNbr;
- BYTE b_CycleSelection;
- BYTE b_InterruptHandling;
- BYTE b_Action;
+ unsigned char b_ModulNbr;
+ unsigned char b_PulseEncoderNbr;
+ unsigned char b_CycleSelection;
+ unsigned char b_InterruptHandling;
+ unsigned char b_Action;
i_ReturnValue = insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_Action = (BYTE) data[0];
- b_PulseEncoderNbr = (BYTE) data[1];
- b_CycleSelection = (BYTE) data[2];
- b_InterruptHandling = (BYTE) data[3];
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_Action = (unsigned char) data[0];
+ b_PulseEncoderNbr = (unsigned char) data[1];
+ b_CycleSelection = (unsigned char) data[2];
+ b_InterruptHandling = (unsigned char) data[3];
/***********************************/
/* Test the selected module number */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadPulseEncoderStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PulseEncoderNbr, |
-| PBYTE_ pb_Status) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PulseEncoderNbr, |
+| unsigned char *_ pb_Status) |
+----------------------------------------------------------------------------+
| Task APCI1710_PULSEENCODER_READ : Reads the pulse encoder status
and valuefrom selected pulse |
| encoder (b_PulseEncoderNbr) from selected module |
| (b_ModulNbr). |
+----------------------------------------------------------------------------+
- BYTE b_Type; data[0]
+ unsigned char b_Type; data[0]
APCI1710_PULSEENCODER_WRITE
Writes a 32-bit value (ul_WriteValue) into the selected|
| pulse encoder (b_PulseEncoderNbr) from selected module |
| (b_ModulNbr). This operation set the new start pulse |
| encoder value.
APCI1710_PULSEENCODER_READ
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| CRAREF() BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| CRAREF() unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
-| data[1] BYTE_ b_PulseEncoderNbr : Pulse encoder selection |
+| data[1] unsigned char_ b_PulseEncoderNbr : Pulse encoder selection |
| (0 to 3)
APCI1710_PULSEENCODER_WRITE
data[2] ULONG_ ul_WriteValue : 32-bit value to be |
| written |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_Status : Pulse encoder status. |
+| Output Parameters : unsigned char *_ pb_Status : Pulse encoder status. |
| 0 : No overflow occur|
| 1 : Overflow occur
PULONG_ pul_ReadValue : Pulse encoder value | |
+----------------------------------------------------------------------------+
*/
-/*_INT_ i_APCI1710_ReadPulseEncoderStatus (BYTE_ b_BoardHandle,
- BYTE_ b_ModulNbr,
- BYTE_ b_PulseEncoderNbr,
+/*_INT_ i_APCI1710_ReadPulseEncoderStatus (unsigned char_ b_BoardHandle,
+ unsigned char_ b_ModulNbr,
+ unsigned char_ b_PulseEncoderNbr,
- PBYTE_ pb_Status)
+ unsigned char *_ pb_Status)
*/
INT i_APCI1710_InsnBitsReadWritePulseEncoder(struct comedi_device * dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
DWORD dw_StatusRegister;
- BYTE b_ModulNbr;
- BYTE b_PulseEncoderNbr;
- PBYTE pb_Status;
- BYTE b_Type;
+ unsigned char b_ModulNbr;
+ unsigned char b_PulseEncoderNbr;
+ unsigned char * pb_Status;
+ unsigned char b_Type;
PULONG pul_ReadValue;
ULONG ul_WriteValue;
i_ReturnValue = insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_Type = (BYTE) data[0];
- b_PulseEncoderNbr = (BYTE) data[1];
- pb_Status = (PBYTE) & data[0];
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_Type = (unsigned char) data[0];
+ b_PulseEncoderNbr = (unsigned char) data[1];
+ pb_Status = (unsigned char *) & data[0];
pul_ReadValue = (PULONG) & data[1];
/***********************************/
dw_StatusRegister;
*pb_Status =
- (BYTE) (devpriv->
+ (unsigned char) (devpriv->
s_ModuleInfo[b_ModulNbr].
s_PulseEncoderModuleInfo.
dw_StatusRegister >> (1 +
INT i_APCI1710_InsnConfigPWM(struct comedi_device * dev, struct comedi_subdevice * s,
struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_ConfigType;
+ unsigned char b_ConfigType;
INT i_ReturnValue = 0;
b_ConfigType = CR_CHAN(insn->chanspec);
switch (b_ConfigType) {
case APCI1710_PWM_INIT:
- i_ReturnValue = i_APCI1710_InitPWM(dev, (BYTE) CR_AREF(insn->chanspec), // b_ModulNbr
- (BYTE) data[0], //b_PWM
- (BYTE) data[1], // b_ClockSelection
- (BYTE) data[2], // b_TimingUnit
+ i_ReturnValue = i_APCI1710_InitPWM(dev, (unsigned char) CR_AREF(insn->chanspec), // b_ModulNbr
+ (unsigned char) data[0], //b_PWM
+ (unsigned char) data[1], // b_ClockSelection
+ (unsigned char) data[2], // b_TimingUnit
(ULONG) data[3], //ul_LowTiming
(ULONG) data[4], //ul_HighTiming
(PULONG) & data[0], //pul_RealLowTiming
break;
case APCI1710_PWM_GETINITDATA:
- i_ReturnValue = i_APCI1710_GetPWMInitialisation(dev, (BYTE) CR_AREF(insn->chanspec), // b_ModulNbr
- (BYTE) data[0], //b_PWM
- (PBYTE) & data[0], //pb_TimingUnit
+ i_ReturnValue = i_APCI1710_GetPWMInitialisation(dev, (unsigned char) CR_AREF(insn->chanspec), // b_ModulNbr
+ (unsigned char) data[0], //b_PWM
+ (unsigned char *) & data[0], //pb_TimingUnit
(PULONG) & data[1], //pul_LowTiming
(PULONG) & data[2], //pul_HighTiming
- (PBYTE) & data[3], // pb_StartLevel
- (PBYTE) & data[4], // pb_StopMode
- (PBYTE) & data[5], // pb_StopLevel
- (PBYTE) & data[6], // pb_ExternGate
- (PBYTE) & data[7], // pb_InterruptEnable
- (PBYTE) & data[8] // pb_Enable
+ (unsigned char *) & data[3], // pb_StartLevel
+ (unsigned char *) & data[4], // pb_StopMode
+ (unsigned char *) & data[5], // pb_StopLevel
+ (unsigned char *) & data[6], // pb_ExternGate
+ (unsigned char *) & data[7], // pb_InterruptEnable
+ (unsigned char *) & data[8] // pb_Enable
);
break;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitPWM |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PWM, |
-| BYTE_ b_ClockSelection, |
-| BYTE_ b_TimingUnit, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PWM, |
+| unsigned char_ b_ClockSelection, |
+| unsigned char_ b_TimingUnit, |
| ULONG_ ul_LowTiming, |
| ULONG_ ul_HighTiming, |
| PULONG_ pul_RealLowTiming, |
| You must calling this function be for you call any |
| other function witch access of the PWM. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure|
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure|
| (0 to 3) |
-| BYTE_ b_PWM : Selected PWM (0 or 1). |
-| BYTE_ b_ClockSelection : Selection from PCI bus |
+| unsigned char_ b_PWM : Selected PWM (0 or 1). |
+| unsigned char_ b_ClockSelection : Selection from PCI bus |
| clock |
| - APCI1710_30MHZ : |
| The PC have a 30 MHz |
| The APCI-1710 have a |
| integrated 40Mhz |
| quartz. |
-| BYTE_ b_TimingUnit : Base timing Unit (0 to 4) |
+| unsigned char_ b_TimingUnit : Base timing Unit (0 to 4) |
| 0 : ns |
| 1 : æs |
| 2 : ms |
*/
INT i_APCI1710_InitPWM(struct comedi_device * dev,
- BYTE b_ModulNbr,
- BYTE b_PWM,
- BYTE b_ClockSelection,
- BYTE b_TimingUnit,
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM,
+ unsigned char b_ClockSelection,
+ unsigned char b_TimingUnit,
ULONG ul_LowTiming,
ULONG ul_HighTiming,
PULONG pul_RealLowTiming, PULONG pul_RealHighTiming)
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetPWMInitialisation |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PWM, |
-| PBYTE_ pb_TimingUnit, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PWM, |
+| unsigned char *_ pb_TimingUnit, |
| PULONG_ pul_LowTiming, |
| PULONG_ pul_HighTiming, |
-| PBYTE_ pb_StartLevel, |
-| PBYTE_ pb_StopMode, |
-| PBYTE_ pb_StopLevel, |
-| PBYTE_ pb_ExternGate, |
-| PBYTE_ pb_InterruptEnable, |
-| PBYTE_ pb_Enable) |
+| unsigned char *_ pb_StartLevel, |
+| unsigned char *_ pb_StopMode, |
+| unsigned char *_ pb_StopLevel, |
+| unsigned char *_ pb_ExternGate, |
+| unsigned char *_ pb_InterruptEnable, |
+| unsigned char *_ pb_Enable) |
+----------------------------------------------------------------------------+
| Task : Return the PWM (b_PWM) initialisation from selected |
| module (b_ModulNbr). You must calling the |
| "i_APCI1710_InitPWM" function be for you call this |
| function. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
-| BYTE_ b_PWM : Selected PWM (0 or 1) |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+| unsigned char_ b_PWM : Selected PWM (0 or 1) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_TimingUnit : Base timing Unit (0 to 4) |
+| Output Parameters : unsigned char *_ pb_TimingUnit : Base timing Unit (0 to 4) |
| 0 : ns |
| 1 : æs |
| 2 : ms |
| 4 : mn |
| PULONG_ pul_LowTiming : Low base timing value. |
| PULONG_ pul_HighTiming : High base timing value. |
-| PBYTE_ pb_StartLevel : Start period level |
+| unsigned char *_ pb_StartLevel : Start period level |
| selection |
| 0 : The period start |
| with a low level |
| 1 : The period start |
| with a high level|
-| PBYTE_ pb_StopMode : Stop mode selection |
+| unsigned char *_ pb_StopMode : Stop mode selection |
| 0 : The PWM is stopped |
| directly after the |
| "i_APCI1710_DisablePWM"|
| function the PWM is |
| stopped at the end |
| from last period cycle|
-| PBYTE_ pb_StopLevel : Stop PWM level selection |
+| unsigned char *_ pb_StopLevel : Stop PWM level selection |
| 0 : The output signal |
| keep the level after|
| the |
| the |
| "i_APCI1710_DisablePWM"|
| function |
-| PBYTE_ pb_ExternGate : Extern gate action |
+| unsigned char *_ pb_ExternGate : Extern gate action |
| selection |
| 0 : Extern gate signal |
| not used. |
| 1 : Extern gate signal |
| used. |
-| PBYTE_ pb_InterruptEnable : Enable or disable the PWM |
+| unsigned char *_ pb_InterruptEnable : Enable or disable the PWM |
| interrupt. |
| - APCI1710_ENABLE : |
| Enable the PWM interrupt|
| - APCI1710_DISABLE : |
| Disable the PWM |
| interrupt |
-| PBYTE_ pb_Enable : Indicate if the PWM is |
+| unsigned char *_ pb_Enable : Indicate if the PWM is |
| enabled or no |
| 0 : PWM not enabled |
| 1 : PWM enabled |
*/
INT i_APCI1710_GetPWMInitialisation(struct comedi_device * dev,
- BYTE b_ModulNbr,
- BYTE b_PWM,
- PBYTE pb_TimingUnit,
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM,
+ unsigned char * pb_TimingUnit,
PULONG pul_LowTiming,
PULONG pul_HighTiming,
- PBYTE pb_StartLevel,
- PBYTE pb_StopMode,
- PBYTE pb_StopLevel,
- PBYTE pb_ExternGate, PBYTE pb_InterruptEnable, PBYTE pb_Enable)
+ unsigned char * pb_StartLevel,
+ unsigned char * pb_StopMode,
+ unsigned char * pb_StopLevel,
+ unsigned char * pb_ExternGate, unsigned char * pb_InterruptEnable, unsigned char * pb_Enable)
{
INT i_ReturnValue = 0;
DWORD dw_Status;
(64 * b_ModulNbr));
*pb_StartLevel =
- (BYTE) ((dw_Command >> 5) & 1);
+ (unsigned char) ((dw_Command >> 5) & 1);
*pb_StopMode =
- (BYTE) ((dw_Command >> 0) & 1);
+ (unsigned char) ((dw_Command >> 0) & 1);
*pb_StopLevel =
- (BYTE) ((dw_Command >> 1) & 1);
+ (unsigned char) ((dw_Command >> 1) & 1);
*pb_ExternGate =
- (BYTE) ((dw_Command >> 4) & 1);
+ (unsigned char) ((dw_Command >> 4) & 1);
*pb_InterruptEnable =
- (BYTE) ((dw_Command >> 3) & 1);
+ (unsigned char) ((dw_Command >> 3) & 1);
if (*pb_StopLevel) {
*pb_StopLevel =
*pb_StopLevel +
- (BYTE) ((dw_Command >>
+ (unsigned char) ((dw_Command >>
2) & 1);
}
(64 * b_ModulNbr));
*pb_Enable =
- (BYTE) ((dw_Command >> 0) & 1);
+ (unsigned char) ((dw_Command >> 0) & 1);
*pb_TimingUnit = devpriv->
s_ModuleInfo[b_ModulNbr].
INT i_APCI1710_InsnWritePWM(struct comedi_device * dev, struct comedi_subdevice * s,
struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_WriteType;
+ unsigned char b_WriteType;
INT i_ReturnValue = 0;
b_WriteType = CR_CHAN(insn->chanspec);
switch (b_WriteType) {
case APCI1710_PWM_ENABLE:
i_ReturnValue = i_APCI1710_EnablePWM(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (BYTE) data[0],
- (BYTE) data[1],
- (BYTE) data[2],
- (BYTE) data[3], (BYTE) data[4], (BYTE) data[5]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char) data[0],
+ (unsigned char) data[1],
+ (unsigned char) data[2],
+ (unsigned char) data[3], (unsigned char) data[4], (unsigned char) data[5]);
break;
case APCI1710_PWM_DISABLE:
i_ReturnValue = i_APCI1710_DisablePWM(dev,
- (BYTE) CR_AREF(insn->chanspec), (BYTE) data[0]);
+ (unsigned char) CR_AREF(insn->chanspec), (unsigned char) data[0]);
break;
case APCI1710_PWM_NEWTIMING:
i_ReturnValue = i_APCI1710_SetNewPWMTiming(dev,
- (BYTE) CR_AREF(insn->chanspec),
- (BYTE) data[0],
- (BYTE) data[1], (ULONG) data[2], (ULONG) data[3]);
+ (unsigned char) CR_AREF(insn->chanspec),
+ (unsigned char) data[0],
+ (unsigned char) data[1], (ULONG) data[2], (ULONG) data[3]);
break;
default:
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnablePWM |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PWM, |
-| BYTE_ b_StartLevel, |
-| BYTE_ b_StopMode, |
-| BYTE_ b_StopLevel, |
-| BYTE_ b_ExternGate, |
-| BYTE_ b_InterruptEnable) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PWM, |
+| unsigned char_ b_StartLevel, |
+| unsigned char_ b_StopMode, |
+| unsigned char_ b_StopLevel, |
+| unsigned char_ b_ExternGate, |
+| unsigned char_ b_InterruptEnable) |
+----------------------------------------------------------------------------+
| Task : Enable the selected PWM (b_PWM) from selected module |
| (b_ModulNbr). You must calling the "i_APCI1710_InitPWM"|
| See function "i_APCI1710_SetBoardIntRoutineX" and the |
| Interrupt mask description chapter. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number |
| (0 to 3) |
-| BYTE_ b_PWM : Selected PWM (0 or 1) |
-| BYTE_ b_StartLevel : Start period level selection |
+| unsigned char_ b_PWM : Selected PWM (0 or 1) |
+| unsigned char_ b_StartLevel : Start period level selection |
| 0 : The period start with a |
| low level |
| 1 : The period start with a |
| high level |
-| BYTE_ b_StopMode : Stop mode selection |
+| unsigned char_ b_StopMode : Stop mode selection |
| 0 : The PWM is stopped |
| directly after the |
| "i_APCI1710_DisablePWM" |
| function the PWM is |
| stopped at the end from|
| last period cycle. |
-| BYTE_ b_StopLevel : Stop PWM level selection |
+| unsigned char_ b_StopLevel : Stop PWM level selection |
| 0 : The output signal keep |
| the level after the |
| "i_APCI1710_DisablePWM" |
| to high after the |
| "i_APCI1710_DisablePWM" |
| function |
-| BYTE_ b_ExternGate : Extern gate action selection |
+| unsigned char_ b_ExternGate : Extern gate action selection |
| 0 : Extern gate signal not |
| used. |
| 1 : Extern gate signal used.|
-| BYTE_ b_InterruptEnable : Enable or disable the PWM |
+| unsigned char_ b_InterruptEnable : Enable or disable the PWM |
| interrupt. |
| - APCI1710_ENABLE : |
| Enable the PWM interrupt |
*/
INT i_APCI1710_EnablePWM(struct comedi_device * dev,
- BYTE b_ModulNbr,
- BYTE b_PWM,
- BYTE b_StartLevel,
- BYTE b_StopMode,
- BYTE b_StopLevel, BYTE b_ExternGate, BYTE b_InterruptEnable)
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM,
+ unsigned char b_StartLevel,
+ unsigned char b_StopMode,
+ unsigned char b_StopLevel, unsigned char b_ExternGate, unsigned char b_InterruptEnable)
{
INT i_ReturnValue = 0;
DWORD dw_Status;
/*
+----------------------------------------------------------------------------+
-| Function Name : _INT_ i_APCI1710_DisablePWM (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PWM) |
+| Function Name : _INT_ i_APCI1710_DisablePWM (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PWM) |
+----------------------------------------------------------------------------+
| Task : Disable the selected PWM (b_PWM) from selected module |
| (b_ModulNbr). The output signal level depend of the |
| parameters from this function. |
+----------------------------------------------------------------------------+
| Input Parameters :BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
-| BYTE_ b_PWM : Selected PWM (0 or 1) |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+| unsigned char_ b_PWM : Selected PWM (0 or 1) |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
+----------------------------------------------------------------------------+
*/
-INT i_APCI1710_DisablePWM(struct comedi_device * dev, BYTE b_ModulNbr, BYTE b_PWM)
+INT i_APCI1710_DisablePWM(struct comedi_device * dev, unsigned char b_ModulNbr, unsigned char b_PWM)
{
INT i_ReturnValue = 0;
DWORD dw_Status;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_SetNewPWMTiming |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PWM, |
-| BYTE_ b_ClockSelection, |
-| BYTE_ b_TimingUnit, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PWM, |
+| unsigned char_ b_ClockSelection, |
+| unsigned char_ b_TimingUnit, |
| ULONG_ ul_LowTiming, |
| ULONG_ ul_HighTiming) |
+----------------------------------------------------------------------------+
| ul_TimingUnit determine the low/high timing base for |
| the period. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Module number to configure|
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Module number to configure|
| (0 to 3) |
-| BYTE_ b_PWM : Selected PWM (0 or 1). |
-| BYTE_ b_TimingUnit : Base timing Unit (0 to 4) |
+| unsigned char_ b_PWM : Selected PWM (0 or 1). |
+| unsigned char_ b_TimingUnit : Base timing Unit (0 to 4) |
| 0 : ns |
| 1 : æs |
| 2 : ms |
*/
INT i_APCI1710_SetNewPWMTiming(struct comedi_device * dev,
- BYTE b_ModulNbr,
- BYTE b_PWM, BYTE b_TimingUnit, ULONG ul_LowTiming, ULONG ul_HighTiming)
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM, unsigned char b_TimingUnit, ULONG ul_LowTiming, ULONG ul_HighTiming)
{
- BYTE b_ClockSelection;
+ unsigned char b_ClockSelection;
INT i_ReturnValue = 0;
ULONG ul_LowTimerValue = 0;
ULONG ul_HighTimerValue = 0;
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetPWMStatus |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PWM, |
-| PBYTE_ pb_PWMOutputStatus, |
-| PBYTE_ pb_ExternGateStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PWM, |
+| unsigned char *_ pb_PWMOutputStatus, |
+| unsigned char *_ pb_ExternGateStatus) |
+----------------------------------------------------------------------------+
| Task : Return the status from selected PWM (b_PWM) from |
| selected module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_PWM : Selected PWM (0 or 1) |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3)
- b_ModulNbr =(BYTE) CR_AREF(insn->chanspec);
- b_PWM =(BYTE) data[0];
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_PWM : Selected PWM (0 or 1) |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3)
+ b_ModulNbr =(unsigned char) CR_AREF(insn->chanspec);
+ b_PWM =(unsigned char) data[0];
|
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_PWMOutputStatus : Return the PWM output |
+| Output Parameters : unsigned char *_ pb_PWMOutputStatus : Return the PWM output |
| level status. |
| 0 : The PWM output level|
| is low. |
| 1 : The PWM output level|
| is high. |
-| PBYTE_ pb_ExternGateStatus : Return the extern gate |
+| unsigned char *_ pb_ExternGateStatus : Return the extern gate |
| level status. |
| 0 : The extern gate is |
| low. |
| 1 : The extern gate is |
| high.
- pb_PWMOutputStatus =(PBYTE) data[0];
- pb_ExternGateStatus =(PBYTE) data[1]; |
+ pb_PWMOutputStatus =(unsigned char *) data[0];
+ pb_ExternGateStatus =(unsigned char *) data[1]; |
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
| -1: The handle parameter of the board is wrong |
INT i_ReturnValue = 0;
DWORD dw_Status;
- BYTE b_ModulNbr;
- BYTE b_PWM;
- PBYTE pb_PWMOutputStatus;
- PBYTE pb_ExternGateStatus;
+ unsigned char b_ModulNbr;
+ unsigned char b_PWM;
+ unsigned char * pb_PWMOutputStatus;
+ unsigned char * pb_ExternGateStatus;
i_ReturnValue = insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_PWM = (BYTE) CR_CHAN(insn->chanspec);
- pb_PWMOutputStatus = (PBYTE) & data[0];
- pb_ExternGateStatus = (PBYTE) & data[1];
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_PWM = (unsigned char) CR_CHAN(insn->chanspec);
+ pb_PWMOutputStatus = (unsigned char *) & data[0];
+ pb_ExternGateStatus = (unsigned char *) & data[1];
/**************************/
/* Test the module number */
if (dw_Status & 0x1) {
*pb_PWMOutputStatus =
- (BYTE) ((dw_Status >> 7)
+ (unsigned char) ((dw_Status >> 7)
& 1);
*pb_ExternGateStatus =
- (BYTE) ((dw_Status >> 6)
+ (unsigned char) ((dw_Status >> 6)
& 1);
} // if (dw_Status & 0x1)
else {
struct comedi_insn *insn, unsigned int *data);
INT i_APCI1710_InitPWM(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_PWM,
- BYTE b_ClockSelection,
- BYTE b_TimingUnit,
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM,
+ unsigned char b_ClockSelection,
+ unsigned char b_TimingUnit,
ULONG ul_LowTiming,
ULONG ul_HighTiming,
PULONG pul_RealLowTiming, PULONG pul_RealHighTiming);
INT i_APCI1710_GetPWMInitialisation(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_PWM,
- PBYTE pb_TimingUnit,
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM,
+ unsigned char * pb_TimingUnit,
PULONG pul_LowTiming,
PULONG pul_HighTiming,
- PBYTE pb_StartLevel,
- PBYTE pb_StopMode,
- PBYTE pb_StopLevel,
- PBYTE pb_ExternGate,
- PBYTE pb_InterruptEnable, PBYTE pb_Enable);
+ unsigned char * pb_StartLevel,
+ unsigned char * pb_StopMode,
+ unsigned char * pb_StopLevel,
+ unsigned char * pb_ExternGate,
+ unsigned char * pb_InterruptEnable, unsigned char * pb_Enable);
INT i_APCI1710_InsnWritePWM(struct comedi_device *dev, struct comedi_subdevice *s,
struct comedi_insn *insn, unsigned int *data);
INT i_APCI1710_EnablePWM(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_PWM,
- BYTE b_StartLevel,
- BYTE b_StopMode,
- BYTE b_StopLevel, BYTE b_ExternGate,
- BYTE b_InterruptEnable);
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM,
+ unsigned char b_StartLevel,
+ unsigned char b_StopMode,
+ unsigned char b_StopLevel, unsigned char b_ExternGate,
+ unsigned char b_InterruptEnable);
INT i_APCI1710_SetNewPWMTiming(struct comedi_device *dev,
- BYTE b_ModulNbr,
- BYTE b_PWM, BYTE b_TimingUnit,
+ unsigned char b_ModulNbr,
+ unsigned char b_PWM, unsigned char b_TimingUnit,
ULONG ul_LowTiming, ULONG ul_HighTiming);
-INT i_APCI1710_DisablePWM(struct comedi_device *dev, BYTE b_ModulNbr, BYTE b_PWM);
+INT i_APCI1710_DisablePWM(struct comedi_device *dev, unsigned char b_ModulNbr, unsigned char b_PWM);
INT i_APCI1710_InsnReadGetPWMStatus(struct comedi_device *dev, struct comedi_subdevice *s,
struct comedi_insn *insn, unsigned int *data);
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitSSI |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_SSIProfile, |
-| BYTE_ b_PositionTurnLength, |
-| BYTE_ b_TurnCptLength, |
-| BYTE_ b_PCIInputClock, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_SSIProfile, |
+| unsigned char_ b_PositionTurnLength, |
+| unsigned char_ b_TurnCptLength, |
+| unsigned char_ b_PCIInputClock, |
| ULONG_ ul_SSIOutputClock, |
-| BYTE_ b_SSICountingMode) |
+| unsigned char_ b_SSICountingMode) |
+----------------------------------------------------------------------------+
| Task : Configure the SSI operating mode from selected module |
| (b_ModulNbr). You must calling this function be for you|
| call any other function witch access of SSI. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
-| BYTE_ b_SSIProfile : Selection from SSI |
+| unsigned char_ b_SSIProfile : Selection from SSI |
| profile length (2 to 32).|
-| BYTE_ b_PositionTurnLength : Selection from SSI |
+| unsigned char_ b_PositionTurnLength : Selection from SSI |
| position data length |
| (1 to 31). |
-| BYTE_ b_TurnCptLength : Selection from SSI turn |
+| unsigned char_ b_TurnCptLength : Selection from SSI turn |
| counter data length |
| (1 to 31). |
-| BYTE b_PCIInputClock : Selection from PCI bus |
+| unsigned char b_PCIInputClock : Selection from PCI bus |
| clock |
| - APCI1710_30MHZ : |
| The PC have a PCI bus |
| for 30 MHz selection. |
| From 252 to 5 000 000 Hz|
| for 33 MHz selection. |
-| BYTE b_SSICountingMode : SSI counting mode |
+| unsigned char b_SSICountingMode : SSI counting mode |
| selection |
| - APCI1710_BINARY_MODE : |
| Binary counting mode. |
| Gray counting mode.
b_ModulNbr = CR_AREF(insn->chanspec);
- b_SSIProfile = (BYTE) data[0];
- b_PositionTurnLength= (BYTE) data[1];
- b_TurnCptLength = (BYTE) data[2];
- b_PCIInputClock = (BYTE) data[3];
+ b_SSIProfile = (unsigned char) data[0];
+ b_PositionTurnLength= (unsigned char) data[1];
+ b_TurnCptLength = (unsigned char) data[2];
+ b_PCIInputClock = (unsigned char) data[3];
ul_SSIOutputClock = (ULONG) data[4];
- b_SSICountingMode = (BYTE) data[5]; |
+ b_SSICountingMode = (unsigned char) data[5]; |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
{
INT i_ReturnValue = 0;
UINT ui_TimerValue;
- BYTE b_ModulNbr, b_SSIProfile, b_PositionTurnLength, b_TurnCptLength,
+ unsigned char b_ModulNbr, b_SSIProfile, b_PositionTurnLength, b_TurnCptLength,
b_PCIInputClock, b_SSICountingMode;
ULONG ul_SSIOutputClock;
b_ModulNbr = CR_AREF(insn->chanspec);
- b_SSIProfile = (BYTE) data[0];
- b_PositionTurnLength = (BYTE) data[1];
- b_TurnCptLength = (BYTE) data[2];
- b_PCIInputClock = (BYTE) data[3];
+ b_SSIProfile = (unsigned char) data[0];
+ b_PositionTurnLength = (unsigned char) data[1];
+ b_TurnCptLength = (unsigned char) data[2];
+ b_PCIInputClock = (unsigned char) data[3];
ul_SSIOutputClock = (ULONG) data[4];
- b_SSICountingMode = (BYTE) data[5];
+ b_SSICountingMode = (unsigned char) data[5];
i_ReturnValue = insn->n;
/**************************/
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_Read1SSIValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_SelectedSSI, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_SelectedSSI, |
| PULONG_ pul_Position, |
| PULONG_ pul_TurnCpt)
INT i_APCI1710_ReadSSIValue(struct comedi_device *dev,struct comedi_subdevice *s,
or Read all SSI counter (b_SelectedSSI) from |
| selected module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
-| BYTE_ b_SelectedSSI : Selection from SSI |
+| unsigned char_ b_SelectedSSI : Selection from SSI |
| counter (0 to 2)
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_SelectedSSI = (BYTE) CR_CHAN(insn->chanspec); (in case of single ssi)
- b_ReadType = (BYTE) CR_RANGE(insn->chanspec);
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_SelectedSSI = (unsigned char) CR_CHAN(insn->chanspec); (in case of single ssi)
+ b_ReadType = (unsigned char) CR_RANGE(insn->chanspec);
|
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pul_Position : SSI position in the turn |
struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
- BYTE b_Cpt;
- BYTE b_Length;
- BYTE b_Schift;
- BYTE b_SSICpt;
+ unsigned char b_Cpt;
+ unsigned char b_Length;
+ unsigned char b_Schift;
+ unsigned char b_SSICpt;
DWORD dw_And;
DWORD dw_And1;
DWORD dw_And2;
DWORD dw_StatusReg;
DWORD dw_CounterValue;
- BYTE b_ModulNbr;
- BYTE b_SelectedSSI;
- BYTE b_ReadType;
+ unsigned char b_ModulNbr;
+ unsigned char b_SelectedSSI;
+ unsigned char b_ReadType;
PULONG pul_Position;
PULONG pul_TurnCpt;
PULONG pul_Position1;
// For Read all
pul_Position = (PULONG) & data[0]; //0-2
pul_TurnCpt = (PULONG) & data[3]; //3-5
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_SelectedSSI = (BYTE) CR_CHAN(insn->chanspec);
- b_ReadType = (BYTE) CR_RANGE(insn->chanspec);
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_SelectedSSI = (unsigned char) CR_CHAN(insn->chanspec);
+ b_ReadType = (unsigned char) CR_RANGE(insn->chanspec);
/**************************/
/* Test the module number */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadSSI1DigitalInput |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_InputChannel, |
-| PBYTE_ pb_ChannelStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_InputChannel, |
+| unsigned char *_ pb_ChannelStatus) |
+----------------------------------------------------------------------------+
| Task :
(0) Set the digital output from selected SSI moule |
(3)Read the status from all SSI digital inputs from |
| selected SSI module (b_ModulNbr) |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr CR_AREF : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr CR_AREF : Module number to |
| configure (0 to 3) |
-| BYTE_ b_InputChannel CR_CHAN : Selection from digital |
+| unsigned char_ b_InputChannel CR_CHAN : Selection from digital |
| data[0] which IOTYPE input ( 0 to 2) |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_ChannelStatus : Digital input channel |
+| Output Parameters : unsigned char *_ pb_ChannelStatus : Digital input channel |
| data[0] status |
| 0 : Channle is not active|
| 1 : Channle is active |
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg;
- BYTE b_ModulNbr;
- BYTE b_InputChannel;
- PBYTE pb_ChannelStatus;
- PBYTE pb_InputStatus;
- BYTE b_IOType;
+ unsigned char b_ModulNbr;
+ unsigned char b_InputChannel;
+ unsigned char * pb_ChannelStatus;
+ unsigned char * pb_InputStatus;
+ unsigned char b_IOType;
i_ReturnValue = insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_IOType = (BYTE) data[0];
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_IOType = (unsigned char) data[0];
/**************************/
/* Test the module number */
/* Test the digital imnput channel number */
/******************************************/
- b_InputChannel = (BYTE) CR_CHAN(insn->chanspec);
- pb_ChannelStatus = (PBYTE) & data[0];
+ b_InputChannel = (unsigned char) CR_CHAN(insn->chanspec);
+ pb_ChannelStatus = (unsigned char *) & data[0];
if (b_InputChannel <= 2) {
/**************************/
inl(devpriv->s_BoardInfos.
ui_Address + (64 * b_ModulNbr));
*pb_ChannelStatus =
- (BYTE) (((~dw_StatusReg) >> (4 +
+ (unsigned char) (((~dw_StatusReg) >> (4 +
b_InputChannel))
& 1);
} else {
/**************************/
/* Read all digital input */
/**************************/
- pb_InputStatus = (PBYTE) & data[0];
+ pb_InputStatus = (unsigned char *) & data[0];
dw_StatusReg =
inl(devpriv->s_BoardInfos.ui_Address +
(64 * b_ModulNbr));
*pb_InputStatus =
- (BYTE) (((~dw_StatusReg) >> 4) & 7);
+ (unsigned char) (((~dw_StatusReg) >> 4) & 7);
break;
default:
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitTorCounter |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TorCounter, |
-| BYTE_ b_PCIInputClock, |
-| BYTE_ b_TimingUnit, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TorCounter, |
+| unsigned char_ b_PCIInputClock, |
+| unsigned char_ b_TimingUnit, |
| ULONG_ ul_TimingInterval, |
| PULONG_ pul_RealTimingInterval) |
+----------------------------------------------------------------------------+
+----------------------------------------------------------------------------+
| Input Parameters : |
|
- CR_AREF BYTE_ b_ModulNbr : Module number to configure |
+ CR_AREF unsigned char_ b_ModulNbr : Module number to configure |
| (0 to 3) |
-| data[0] BYTE_ b_TorCounter : Tor counter selection |
+| data[0] unsigned char_ b_TorCounter : Tor counter selection |
| (0 or 1). |
-| data[1] BYTE_ b_PCIInputClock : Selection from PCI bus clock|
+| data[1] unsigned char_ b_PCIInputClock : Selection from PCI bus clock|
| - APCI1710_30MHZ : |
| The PC have a PCI bus |
| clock from 30 MHz |
| than it is not possibl to |
| used the gate input for |
| enabled the acquisition |
-| data[2] BYTE_ b_TimingUnit : Base timing unit (0 to 4) |
+| data[2] unsigned char_ b_TimingUnit : Base timing unit (0 to 4) |
| 0 : ns |
| 1 : µs |
| 2 : ms |
ULONG ul_TimerValue = 0;
DWORD dw_Command;
double d_RealTimingInterval = 0;
- BYTE b_ModulNbr;
- BYTE b_TorCounter;
- BYTE b_PCIInputClock;
- BYTE b_TimingUnit;
+ unsigned char b_ModulNbr;
+ unsigned char b_TorCounter;
+ unsigned char b_PCIInputClock;
+ unsigned char b_TimingUnit;
ULONG ul_TimingInterval;
ULONG ul_RealTimingInterval = 0;
i_ReturnValue = insn->n;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
- b_TorCounter = (BYTE) data[0];
- b_PCIInputClock = (BYTE) data[1];
- b_TimingUnit = (BYTE) data[2];
+ b_TorCounter = (unsigned char) data[0];
+ b_PCIInputClock = (unsigned char) data[1];
+ b_TimingUnit = (unsigned char) data[2];
ul_TimingInterval = (ULONG) data[3];
printk("INPUT clock %d\n", b_PCIInputClock);
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_EnableTorCounter |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TorCounter, |
-| BYTE_ b_InputMode, |
-| BYTE_ b_ExternGate, |
-| BYTE_ b_CycleMode, |
-| BYTE_ b_InterruptEnable) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TorCounter, |
+| unsigned char_ b_InputMode, |
+| unsigned char_ b_ExternGate, |
+| unsigned char_ b_CycleMode, |
+| unsigned char_ b_InterruptEnable) |
+----------------------------------------------------------------------------+
| Task : Enable the tor counter (b_TorCounter) from selected |
| module (b_ModulNbr). You must calling the |
| The b_CycleMode parameter determine if you will |
| measured a single or more cycle. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
-| BYTE_ b_TorCounter : Tor counter selection (0 or 1). |
-| BYTE_ b_InputMode : Input signal level selection |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+| unsigned char_ b_TorCounter : Tor counter selection (0 or 1). |
+| unsigned char_ b_InputMode : Input signal level selection |
| 0 : Tor count each low level |
| 1 : Tor count each high level|
-| BYTE_ b_ExternGate : Extern gate action selection |
+| unsigned char_ b_ExternGate : Extern gate action selection |
| 0 : Extern gate signal not |
| used |
| 1 : Extern gate signal used. |
| The gate input is used for the |
| signal B |
| |
-| BYTE_ b_CycleMode : Selected the tor counter |
+| unsigned char_ b_CycleMode : Selected the tor counter |
| acquisition mode |
-| BYTE_ b_InterruptEnable : Enable or disable the |
+| unsigned char_ b_InterruptEnable : Enable or disable the |
| tor counter interrupt. |
| APCI1710_ENABLE: |
| Enable the tor counter |
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_DisableTorCounter |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TorCounter) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TorCounter) |
+----------------------------------------------------------------------------+
| Task : Disable the tor counter (b_TorCounter) from selected |
| module (b_ModulNbr). If you disable the tor counter |
| counter witch the " i_APCI1710_EnableTorCounter" |
| function, the status register is cleared |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
-| BYTE_ b_TorCounter : Tor counter selection (0 or 1). |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+| unsigned char_ b_TorCounter : Tor counter selection (0 or 1). |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
DWORD dw_Status;
DWORD dw_DummyRead;
DWORD dw_ConfigReg;
- BYTE b_ModulNbr, b_Action;
- BYTE b_TorCounter;
- BYTE b_InputMode;
- BYTE b_ExternGate;
- BYTE b_CycleMode;
- BYTE b_InterruptEnable;
-
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_Action = (BYTE) data[0]; // enable or disable
- b_TorCounter = (BYTE) data[1];
- b_InputMode = (BYTE) data[2];
- b_ExternGate = (BYTE) data[3];
- b_CycleMode = (BYTE) data[4];
- b_InterruptEnable = (BYTE) data[5];
+ unsigned char b_ModulNbr, b_Action;
+ unsigned char b_TorCounter;
+ unsigned char b_InputMode;
+ unsigned char b_ExternGate;
+ unsigned char b_CycleMode;
+ unsigned char b_InterruptEnable;
+
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_Action = (unsigned char) data[0]; // enable or disable
+ b_TorCounter = (unsigned char) data[1];
+ b_InputMode = (unsigned char) data[2];
+ b_ExternGate = (unsigned char) data[3];
+ b_CycleMode = (unsigned char) data[4];
+ b_InterruptEnable = (unsigned char) data[5];
i_ReturnValue = insn->n;;
devpriv->tsk_Current = current; // Save the current process task structure
/**************************/
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_GetTorCounterInitialisation |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TorCounter, |
-| PBYTE_ pb_TimingUnit, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TorCounter, |
+| unsigned char *_ pb_TimingUnit, |
| PULONG_ pul_TimingInterval, |
-| PBYTE_ pb_InputMode, |
-| PBYTE_ pb_ExternGate, |
-| PBYTE_ pb_CycleMode, |
-| PBYTE_ pb_Enable, |
-| PBYTE_ pb_InterruptEnable)|
+| unsigned char *_ pb_InputMode, |
+| unsigned char *_ pb_ExternGate, |
+| unsigned char *_ pb_CycleMode, |
+| unsigned char *_ pb_Enable, |
+| unsigned char *_ pb_InterruptEnable)|
+----------------------------------------------------------------------------+
| Task : Enable the tor counter (b_TorCounter) from selected |
| module (b_ModulNbr). You must calling the |
| The b_CycleMode parameter determine if you will |
| measured a single or more cycle. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
-| BYTE_ b_TorCounter : Tor counter selection (0 or 1)
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+| unsigned char_ b_TorCounter : Tor counter selection (0 or 1)
b_ModulNbr = CR_AREF(insn->chanspec);
b_TorCounter = CR_CHAN(insn->chanspec);
. |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_TimingUnit : Base timing unit (0 to 4) |
+| Output Parameters : unsigned char *_ pb_TimingUnit : Base timing unit (0 to 4) |
| 0 : ns |
| 1 : µs |
| 2 : ms |
| 3 : s |
| 4 : mn |
| PULONG_ pul_TimingInterval : Base timing value. |
-| PBYTE_ pb_InputMode : Input signal level |
+| unsigned char *_ pb_InputMode : Input signal level |
| selection |
| 0 : Tor count each low level |
| 1 : Tor count each high level|
-| PBYTE_ pb_ExternGate : Extern gate action |
+| unsigned char *_ pb_ExternGate : Extern gate action |
| selection |
| 0 : Extern gate signal not |
| used |
| 1 : Extern gate signal used|
-| PBYTE_ pb_CycleMode : Tor counter acquisition |
+| unsigned char *_ pb_CycleMode : Tor counter acquisition |
| mode |
-| PBYTE_ pb_Enable : Indicate if the tor counter|
+| unsigned char *_ pb_Enable : Indicate if the tor counter|
| is enabled or no |
| 0 : Tor counter disabled |
| 1 : Tor counter enabled |
-| PBYTE_ pb_InterruptEnable : Enable or disable the |
+| unsigned char *_ pb_InterruptEnable : Enable or disable the |
| tor counter interrupt. |
| APCI1710_ENABLE: |
| Enable the tor counter |
| APCI1710_DISABLE: |
| Disable the tor counter |
| interrupt
- pb_TimingUnit = (PBYTE) &data[0];
+ pb_TimingUnit = (unsigned char *) &data[0];
pul_TimingInterval = (PULONG) &data[1];
- pb_InputMode = (PBYTE) &data[2];
- pb_ExternGate = (PBYTE) &data[3];
- pb_CycleMode = (PBYTE) &data[4];
- pb_Enable = (PBYTE) &data[5];
- pb_InterruptEnable = (PBYTE) &data[6];
+ pb_InputMode = (unsigned char *) &data[2];
+ pb_ExternGate = (unsigned char *) &data[3];
+ pb_CycleMode = (unsigned char *) &data[4];
+ pb_Enable = (unsigned char *) &data[5];
+ pb_InterruptEnable = (unsigned char *) &data[6];
|
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
{
INT i_ReturnValue = 0;
DWORD dw_Status;
- BYTE b_ModulNbr;
- BYTE b_TorCounter;
- PBYTE pb_TimingUnit;
+ unsigned char b_ModulNbr;
+ unsigned char b_TorCounter;
+ unsigned char * pb_TimingUnit;
PULONG pul_TimingInterval;
- PBYTE pb_InputMode;
- PBYTE pb_ExternGate;
- PBYTE pb_CycleMode;
- PBYTE pb_Enable;
- PBYTE pb_InterruptEnable;
+ unsigned char * pb_InputMode;
+ unsigned char * pb_ExternGate;
+ unsigned char * pb_CycleMode;
+ unsigned char * pb_Enable;
+ unsigned char * pb_InterruptEnable;
i_ReturnValue = insn->n;
b_ModulNbr = CR_AREF(insn->chanspec);
b_TorCounter = CR_CHAN(insn->chanspec);
- pb_TimingUnit = (PBYTE) & data[0];
+ pb_TimingUnit = (unsigned char *) & data[0];
pul_TimingInterval = (PULONG) & data[1];
- pb_InputMode = (PBYTE) & data[2];
- pb_ExternGate = (PBYTE) & data[3];
- pb_CycleMode = (PBYTE) & data[4];
- pb_Enable = (PBYTE) & data[5];
- pb_InterruptEnable = (PBYTE) & data[6];
+ pb_InputMode = (unsigned char *) & data[2];
+ pb_ExternGate = (unsigned char *) & data[3];
+ pb_CycleMode = (unsigned char *) & data[4];
+ pb_Enable = (unsigned char *) & data[5];
+ pb_InterruptEnable = (unsigned char *) & data[6];
/**************************/
/* Test the module number */
(64 * b_ModulNbr));
*pb_CycleMode =
- (BYTE) ((dw_Status >> 4) & 1);
+ (unsigned char) ((dw_Status >> 4) & 1);
*pb_InterruptEnable =
- (BYTE) ((dw_Status >> 5) & 1);
+ (unsigned char) ((dw_Status >> 5) & 1);
/******************************************************/
/* Test if extern gate used for clock or for signal B */
} // if (dw_Status & 0x600)
else {
*pb_InputMode =
- (BYTE) ((dw_Status >> 6)
+ (unsigned char) ((dw_Status >> 6)
& 1);
*pb_ExternGate =
- (BYTE) ((dw_Status >> 7)
+ (unsigned char) ((dw_Status >> 7)
& 1);
} // if (dw_Status & 0x600)
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadTorCounterValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_TorCounter, |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_TorCounter, |
| UINT_ ui_TimeOut, |
-| PBYTE_ pb_TorCounterStatus, |
+| unsigned char *_ pb_TorCounterStatus, |
| PULONG_ pul_TorCounterValue) |
+----------------------------------------------------------------------------+
| Task case APCI1710_TOR_GETPROGRESSSTATUS: Return the tor counter
| (pul_TorCounterValue) after a conting cycle stop |
| from selected tor counter module (b_ModulNbr). |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3) |
-| BYTE_ b_TorCounter : Tor counter selection (0 or 1).
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3) |
+| unsigned char_ b_TorCounter : Tor counter selection (0 or 1).
b_ModulNbr = CR_AREF(insn->chanspec);
- b_ReadType = (BYTE) data[0];
- b_TorCounter = (BYTE) data[1];
+ b_ReadType = (unsigned char) data[0];
+ b_TorCounter = (unsigned char) data[1];
ui_TimeOut = (UINT) data[2]; |
+----------------------------------------------------------------------------+
-| Output Parameters : PBYTE_ pb_TorCounterStatus : Return the tor counter |
+| Output Parameters : unsigned char *_ pb_TorCounterStatus : Return the tor counter |
| status. |
| 0 : Conting cycle not started|
| Software gate not set. |
| "i_APCI1710_InitTorCounter"|
| 4 : Timeeout occur |
| PULONG pul_TorCounterValue : Tor counter value.
- pb_TorCounterStatus=(PBYTE) &data[0];
+ pb_TorCounterStatus=(unsigned char *) &data[0];
pul_TorCounterValue=(PULONG) &data[1]; |
+----------------------------------------------------------------------------+
| Return Value : 0: No error |
DWORD dw_Status;
DWORD dw_TimeOut = 0;
- BYTE b_ModulNbr;
- BYTE b_TorCounter;
- BYTE b_ReadType;
+ unsigned char b_ModulNbr;
+ unsigned char b_TorCounter;
+ unsigned char b_ReadType;
UINT ui_TimeOut;
- PBYTE pb_TorCounterStatus;
+ unsigned char * pb_TorCounterStatus;
PULONG pul_TorCounterValue;
i_ReturnValue = insn->n;
b_ModulNbr = CR_AREF(insn->chanspec);
- b_ReadType = (BYTE) data[0];
- b_TorCounter = (BYTE) data[1];
+ b_ReadType = (unsigned char) data[0];
+ b_TorCounter = (unsigned char) data[1];
ui_TimeOut = (UINT) data[2];
- pb_TorCounterStatus = (PBYTE) & data[0];
+ pb_TorCounterStatus = (unsigned char *) & data[0];
pul_TorCounterValue = (PULONG) & data[1];
/**************************/
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_InitTTLIODirection |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_PortAMode, |
-| BYTE_ b_PortBMode, |
-| BYTE_ b_PortCMode, |
-| BYTE_ b_PortDMode) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_PortAMode, |
+| unsigned char_ b_PortBMode, |
+| unsigned char_ b_PortCMode, |
+| unsigned char_ b_PortDMode) |
+----------------------------------------------------------------------------+
| Task APCI1710_TTL_INIT (using defaults) : Configure the TTL I/O operating mode from selected |
| module (b_ModulNbr). You must calling this function be|
APCI1710_TTL_INITDIRECTION(user inputs for direction)
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3)
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_InitType = (BYTE) data[0];
- b_PortAMode = (BYTE) data[1];
- b_PortBMode = (BYTE) data[2];
- b_PortCMode = (BYTE) data[3];
- b_PortDMode = (BYTE) data[4];|
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_InitType = (unsigned char) data[0];
+ b_PortAMode = (unsigned char) data[1];
+ b_PortBMode = (unsigned char) data[2];
+ b_PortCMode = (unsigned char) data[3];
+ b_PortDMode = (unsigned char) data[4];|
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = 0;
- BYTE b_ModulNbr;
- BYTE b_InitType;
- BYTE b_PortAMode;
- BYTE b_PortBMode;
- BYTE b_PortCMode;
- BYTE b_PortDMode;
-
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
- b_InitType = (BYTE) data[0];
+ unsigned char b_ModulNbr;
+ unsigned char b_InitType;
+ unsigned char b_PortAMode;
+ unsigned char b_PortBMode;
+ unsigned char b_PortCMode;
+ unsigned char b_PortDMode;
+
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
+ b_InitType = (unsigned char) data[0];
i_ReturnValue = insn->n;
/**************************/
case APCI1710_TTL_INITDIRECTION:
- b_PortAMode = (BYTE) data[1];
- b_PortBMode = (BYTE) data[2];
- b_PortCMode = (BYTE) data[3];
- b_PortDMode = (BYTE) data[4];
+ b_PortAMode = (unsigned char) data[1];
+ b_PortBMode = (unsigned char) data[2];
+ b_PortCMode = (unsigned char) data[3];
+ b_PortDMode = (unsigned char) data[4];
/********************/
/* Test the version */
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_ReadTTLIOChannelValue |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_SelectedPort, |
-| BYTE_ b_InputChannel, |
-| PBYTE_ pb_ChannelStatus) |
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_SelectedPort, |
+| unsigned char_ b_InputChannel, |
+| unsigned char *_ pb_ChannelStatus) |
+----------------------------------------------------------------------------+
| Task : Read the status from selected TTL digital input |
| (b_InputChannel)
+----------------------------------------------------------------------------+
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 7) |
-| BYTE_ b_SelectedPort, : Selection from TTL I/O |
+| unsigned char_ b_SelectedPort, : Selection from TTL I/O |
| port (0 to 2) |
| 0 : Port A selection |
| 1 : Port B selection |
| 2 : Port C selection |
| 3 : Port D selection |
-| BYTE_ b_InputChannel : Selection from digital |
+| unsigned char_ b_InputChannel : Selection from digital |
| input ( 0 to 2)
APCI1710_TTL_READCHANNEL
b_ModulNbr = CR_AREF(insn->chanspec);
b_SelectedPort= CR_RANGE(insn->chanspec);
b_InputChannel= CR_CHAN(insn->chanspec);
- b_ReadType = (BYTE) data[0];
+ b_ReadType = (unsigned char) data[0];
APCI1710_TTL_READPORT|
b_ModulNbr = CR_AREF(insn->chanspec);
b_SelectedPort= CR_RANGE(insn->chanspec);
- b_ReadType = (BYTE) data[0];
+ b_ReadType = (unsigned char) data[0];
+----------------------------------------------------------------------------+
| Output Parameters : data[0]
- PBYTE_ pb_ChannelStatus : Digital input channel |
+ unsigned char *_ pb_ChannelStatus : Digital input channel |
| status |
| 0 : Channle is not active|
| 1 : Channle is active |
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg;
- BYTE b_ModulNbr;
- BYTE b_SelectedPort;
- BYTE b_InputChannel;
- BYTE b_ReadType;
- PBYTE pb_ChannelStatus;
- PBYTE pb_PortValue;
+ unsigned char b_ModulNbr;
+ unsigned char b_SelectedPort;
+ unsigned char b_InputChannel;
+ unsigned char b_ReadType;
+ unsigned char * pb_ChannelStatus;
+ unsigned char * pb_PortValue;
i_ReturnValue = insn->n;
- b_ReadType = (BYTE) data[0];
+ b_ReadType = (unsigned char) data[0];
b_ModulNbr = CR_AREF(insn->chanspec);
b_SelectedPort = CR_RANGE(insn->chanspec);
b_InputChannel = CR_CHAN(insn->chanspec);
switch (b_ReadType) {
case APCI1710_TTL_READCHANNEL:
- pb_ChannelStatus = (PBYTE) & data[0];
+ pb_ChannelStatus = (unsigned char *) & data[0];
/********************************/
/* Test the TTL I/O port number */
/********************************/
*pb_ChannelStatus
=
- (BYTE) (
+ (unsigned char) (
(dw_StatusReg
>>
(8 * b_SelectedPort)) >> b_InputChannel) & 1;
break;
case APCI1710_TTL_READPORT:
- pb_PortValue = (PBYTE) & data[0];
+ pb_PortValue = (unsigned char *) & data[0];
/********************************/
/* Test the TTL I/O port number */
/********************************/
(64 * b_ModulNbr));
*pb_PortValue =
- (BYTE) (
+ (unsigned char) (
(dw_StatusReg >>
(8 * b_SelectedPort)) & 0xFF);
} else {
| (port A, port B and port C) from selected TTL |
| module (b_ModulNbr) |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710|
-| BYTE_ b_ModulNbr : Module number to |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710|
+| unsigned char_ b_ModulNbr : Module number to |
| configure (0 to 3) |
+----------------------------------------------------------------------------+
| Output Parameters : PULONG_ pul_PortValue : Digital TTL inputs port |
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg;
- BYTE b_ModulNbr;
+ unsigned char b_ModulNbr;
PULONG pul_PortValue;
- b_ModulNbr = (BYTE) CR_AREF(insn->chanspec);
+ b_ModulNbr = (unsigned char) CR_AREF(insn->chanspec);
i_ReturnValue = insn->n;
pul_PortValue = (PULONG) & data[0];
/*
+----------------------------------------------------------------------------+
| Function Name : _INT_ i_APCI1710_SetTTLIOChlOn |
-| (BYTE_ b_BoardHandle, |
-| BYTE_ b_ModulNbr, |
-| BYTE_ b_OutputChannel)
+| (unsigned char_ b_BoardHandle, |
+| unsigned char_ b_ModulNbr, |
+| unsigned char_ b_OutputChannel)
INT i_APCI1710_InsnWriteSetTTLIOChlOnOff(struct comedi_device *dev,struct comedi_subdevice *s,
struct comedi_insn *insn,unsigned int *data) |
+----------------------------------------------------------------------------+
| parameter b_Channel. Setting an output means setting |
| an ouput high. |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE_ b_BoardHandle : Handle of board APCI-1710 |
-| BYTE_ b_ModulNbr : Selected module number (0 to 3)|
-| BYTE_ b_OutputChannel : Selection from digital output |
+| Input Parameters : unsigned char_ b_BoardHandle : Handle of board APCI-1710 |
+| unsigned char_ b_ModulNbr : Selected module number (0 to 3)|
+| unsigned char_ b_OutputChannel : Selection from digital output |
| channel (0 or 1) |
| 0 : PD0 |
| 1 : PD1 |
{
INT i_ReturnValue = 0;
DWORD dw_StatusReg = 0;
- BYTE b_ModulNbr;
- BYTE b_OutputChannel;
+ unsigned char b_ModulNbr;
+ unsigned char b_OutputChannel;
UINT ui_State;
i_ReturnValue = insn->n;
INT i_Counter = 0;
INT i_WordCounter;
INT i;
- BYTE pb_ReadByte[1];
- BYTE b_ReadLowByte = 0;
- BYTE b_ReadHighByte = 0;
- BYTE b_SelectedAddressLow = 0;
- BYTE b_SelectedAddressHigh = 0;
+ unsigned char pb_ReadByte[1];
+ unsigned char b_ReadLowByte = 0;
+ unsigned char b_ReadHighByte = 0;
+ unsigned char b_SelectedAddressLow = 0;
+ unsigned char b_SelectedAddressHigh = 0;
WORD w_ReadWord = 0;
for (i_WordCounter = 0; i_WordCounter < i_NbOfWordsToRead;
#define SUCCESS 1
/* variable type definition */
-typedef unsigned char BYTE, *PBYTE;
typedef short SHORT, *PSHORT;
typedef unsigned short USHORT, *PUSHORT;
typedef unsigned short WORD, *PWORD;
typedef const struct comedi_lrange *PCRANGE;
-#define LOBYTE(W) (BYTE)((W) & 0xFF)
-#define HIBYTE(W) (BYTE)(((W) >> 8) & 0xFF)
+#define LOBYTE(W) (unsigned char)((W) & 0xFF)
+#define HIBYTE(W) (unsigned char)(((W) >> 8) & 0xFF)
#define MAKEWORD(H, L) (USHORT)((L) | ((H) << 8))
#define LOWORD(W) (USHORT)((W) & 0xFFFF)
#define HIWORD(W) (USHORT)(((W) >> 16) & 0xFFFF)
INT i_Dma; // dma present or not
INT i_Timer; // timer subdevice present or not
- BYTE b_AvailableConvertUnit;
+ unsigned char b_AvailableConvertUnit;
UINT ui_MinAcquisitiontimeNs; // Minimum Acquisition in Nano secs
UINT ui_MinDelaytimeNs; // Minimum Delay in Nano secs
struct {
union {
struct {
- BYTE b_ModeRegister1;
- BYTE b_ModeRegister2;
- BYTE b_ModeRegister3;
- BYTE b_ModeRegister4;
+ unsigned char b_ModeRegister1;
+ unsigned char b_ModeRegister2;
+ unsigned char b_ModeRegister3;
+ unsigned char b_ModeRegister4;
} s_ByteModeRegister;
DWORD dw_ModeRegister1_2_3_4;
} s_ModeRegister;
/* SSI infos */
struct {
- BYTE b_SSIProfile;
- BYTE b_PositionTurnLength;
- BYTE b_TurnCptLength;
- BYTE b_SSIInit;
+ unsigned char b_SSIProfile;
+ unsigned char b_PositionTurnLength;
+ unsigned char b_TurnCptLength;
+ unsigned char b_SSIInit;
} s_SSICounterInfo;
/* TTL I/O infos */
struct {
- BYTE b_TTLInit;
- BYTE b_PortConfiguration[4];
+ unsigned char b_TTLInit;
+ unsigned char b_PortConfiguration[4];
} s_TTLIOInfo;
/* Digital I/O infos */
struct {
- BYTE b_DigitalInit;
- BYTE b_ChannelAMode;
- BYTE b_ChannelBMode;
- BYTE b_OutputMemoryEnabled;
+ unsigned char b_DigitalInit;
+ unsigned char b_ChannelAMode;
+ unsigned char b_ChannelBMode;
+ unsigned char b_OutputMemoryEnabled;
DWORD dw_OutputMemory;
} s_DigitalIOInfo;
struct {
struct {
- BYTE b_82X54Init;
- BYTE b_InputClockSelection;
- BYTE b_InputClockLevel;
- BYTE b_OutputLevel;
- BYTE b_HardwareGateLevel;
+ unsigned char b_82X54Init;
+ unsigned char b_InputClockSelection;
+ unsigned char b_InputClockLevel;
+ unsigned char b_OutputLevel;
+ unsigned char b_HardwareGateLevel;
DWORD dw_ConfigurationWord;
} s_82X54TimerInfo[3];
- BYTE b_InterruptMask;
+ unsigned char b_InterruptMask;
} s_82X54ModuleInfo;
/*********************/
/*********************/
struct {
- BYTE b_ChronoInit;
- BYTE b_InterruptMask;
- BYTE b_PCIInputClock;
- BYTE b_TimingUnit;
- BYTE b_CycleMode;
+ unsigned char b_ChronoInit;
+ unsigned char b_InterruptMask;
+ unsigned char b_PCIInputClock;
+ unsigned char b_TimingUnit;
+ unsigned char b_CycleMode;
double d_TimingInterval;
DWORD dw_ConfigReg;
} s_ChronoModuleInfo;
struct {
struct {
- BYTE b_PulseEncoderInit;
+ unsigned char b_PulseEncoderInit;
} s_PulseEncoderInfo[4];
DWORD dw_SetRegister;
DWORD dw_ControlRegister;
/* Tor conter infos */
struct {
struct {
- BYTE b_TorCounterInit;
- BYTE b_TimingUnit;
- BYTE b_InterruptEnable;
+ unsigned char b_TorCounterInit;
+ unsigned char b_TimingUnit;
+ unsigned char b_InterruptEnable;
double d_TimingInterval;
ULONG ul_RealTimingInterval;
} s_TorCounterInfo[2];
- BYTE b_PCIInputClock;
+ unsigned char b_PCIInputClock;
} s_TorCounterModuleInfo;
/* PWM infos */
struct {
struct {
- BYTE b_PWMInit;
- BYTE b_TimingUnit;
- BYTE b_InterruptEnable;
+ unsigned char b_PWMInit;
+ unsigned char b_TimingUnit;
+ unsigned char b_InterruptEnable;
double d_LowTiming;
double d_HighTiming;
ULONG ul_RealLowTiming;
ULONG ul_RealHighTiming;
} s_PWMInfo[2];
- BYTE b_ClockSelection;
+ unsigned char b_ClockSelection;
} s_PWMModuleInfo;
/* ETM infos */
struct {
struct {
- BYTE b_ETMEnable;
- BYTE b_ETMInterrupt;
+ unsigned char b_ETMEnable;
+ unsigned char b_ETMInterrupt;
} s_ETMInfo[2];
- BYTE b_ETMInit;
- BYTE b_TimingUnit;
- BYTE b_ClockSelection;
+ unsigned char b_ETMInit;
+ unsigned char b_TimingUnit;
+ unsigned char b_ClockSelection;
double d_TimingInterval;
ULONG ul_Timing;
} s_ETMModuleInfo;
/* CDA infos */
struct {
- BYTE b_CDAEnable;
- BYTE b_CDAInterrupt;
- BYTE b_CDAInit;
- BYTE b_FctSelection;
- BYTE b_CDAReadFIFOOverflow;
+ unsigned char b_CDAEnable;
+ unsigned char b_CDAInterrupt;
+ unsigned char b_CDAInit;
+ unsigned char b_FctSelection;
+ unsigned char b_CDAReadFIFOOverflow;
} s_CDAModuleInfo;
} str_ModuleInfo;
INT i_IobaseReserved;
ULONG_PTR dw_AiBase;
struct pcilst_struct *amcc; // ptr too AMCC data
- BYTE allocated; // we have blocked card
- BYTE b_ValidDriver; // driver is ok
- BYTE b_AiContinuous; // we do unlimited AI
- BYTE b_AiInitialisation;
+ unsigned char allocated; // we have blocked card
+ unsigned char b_ValidDriver; // driver is ok
+ unsigned char b_AiContinuous; // we do unlimited AI
+ unsigned char b_AiInitialisation;
UINT ui_AiActualScan; //how many scans we finished
UINT ui_AiBufferPtr; // data buffer ptr in samples
UINT ui_AiNbrofChannels; // how many channels is measured
UINT ui_AiActualScanPosition; // position in actual scan
PUINT pui_AiChannelList; // actual chanlist
UINT ui_AiChannelList[32]; // actual chanlist
- BYTE b_AiChannelConfiguration[32]; // actual chanlist
+ unsigned char b_AiChannelConfiguration[32]; // actual chanlist
UINT ui_AiReadData[32];
DWORD dw_AiInitialised;
UINT ui_AiTimer0; //Timer Constant for Timer0
short *AiData; // Pointer to sample data
UINT ui_AiNbrofScans; // number of scans to do
USHORT us_UseDma; // To use Dma or not
- BYTE b_DmaDoubleBuffer; // we can use double buffering
+ unsigned char b_DmaDoubleBuffer; // we can use double buffering
UINT ui_DmaActualBuffer; // which buffer is used now
//*UPDATE-0.7.57->0.7.68
//ULONG ul_DmaBufferVirtual[2];// pointers to begin of DMA buffer
UINT ui_DmaBufferUsesize[2]; // which size we may now used for transfer
UINT ui_DmaBufferSamples[2]; // size in samples
UINT ui_DmaBufferPages[2]; // number of pages in buffer
- BYTE b_DigitalOutputRegister; // Digital Output Register
- BYTE b_OutputMemoryStatus;
- BYTE b_AnalogInputChannelNbr; // Analog input channel Nbr
- BYTE b_AnalogOutputChannelNbr; // Analog input Output Nbr
- BYTE b_TimerSelectMode; // Contain data written at iobase + 0C
- BYTE b_ModeSelectRegister; // Contain data written at iobase + 0E
+ unsigned char b_DigitalOutputRegister; // Digital Output Register
+ unsigned char b_OutputMemoryStatus;
+ unsigned char b_AnalogInputChannelNbr; // Analog input channel Nbr
+ unsigned char b_AnalogOutputChannelNbr; // Analog input Output Nbr
+ unsigned char b_TimerSelectMode; // Contain data written at iobase + 0C
+ unsigned char b_ModeSelectRegister; // Contain data written at iobase + 0E
USHORT us_OutputRegister; // Contain data written at iobase + 0
- BYTE b_InterruptState;
- BYTE b_TimerInit; // Specify if InitTimerWatchdog was load
- BYTE b_TimerStarted; // Specify if timer 2 is running or not
- BYTE b_Timer2Mode; // Specify the timer 2 mode
- BYTE b_Timer2Interrupt; //Timer2 interrupt enable or disable
- BYTE b_AiCyclicAcquisition; // indicate cyclic acquisition
- BYTE b_InterruptMode; // eoc eos or dma
- BYTE b_EocEosInterrupt; // Enable disable eoc eos interrupt
+ unsigned char b_InterruptState;
+ unsigned char b_TimerInit; // Specify if InitTimerWatchdog was load
+ unsigned char b_TimerStarted; // Specify if timer 2 is running or not
+ unsigned char b_Timer2Mode; // Specify the timer 2 mode
+ unsigned char b_Timer2Interrupt; //Timer2 interrupt enable or disable
+ unsigned char b_AiCyclicAcquisition; // indicate cyclic acquisition
+ unsigned char b_InterruptMode; // eoc eos or dma
+ unsigned char b_EocEosInterrupt; // Enable disable eoc eos interrupt
UINT ui_EocEosConversionTime;
- BYTE b_EocEosConversionTimeBase;
- BYTE b_SingelDiff;
- BYTE b_ExttrigEnable; /* To enable or disable external trigger */
+ unsigned char b_EocEosConversionTimeBase;
+ unsigned char b_SingelDiff;
+ unsigned char b_ExttrigEnable; /* To enable or disable external trigger */
/* Pointer to the current process */
struct task_struct *tsk_Current;
struct {
UINT ui_Address; /* Board address */
UINT ui_FlashAddress;
- BYTE b_InterruptNbr; /* Board interrupt number */
- BYTE b_SlotNumber; /* PCI slot number */
- BYTE b_BoardVersion;
+ unsigned char b_InterruptNbr; /* Board interrupt number */
+ unsigned char b_SlotNumber; /* PCI slot number */
+ unsigned char b_BoardVersion;
DWORD dw_MolduleConfiguration[4]; /* Module config */
} s_BoardInfos;
UINT ui_Read; /* Read FIFO */
UINT ui_Write; /* Write FIFO */
struct {
- BYTE b_OldModuleMask;
+ unsigned char b_OldModuleMask;
ULONG ul_OldInterruptMask; /* Interrupt mask */
ULONG ul_OldCounterLatchValue; /* Interrupt counter value */
} s_FIFOInterruptParameters[APCI1710_SAVE_INTERRUPT];
#define EEPROM_TIMER_WATCHDOG_COUNTER 10
struct str_Functionality {
- BYTE b_Type;
+ unsigned char b_Type;
WORD w_Address;
};
typedef struct {
WORD w_HeaderSize;
- BYTE b_Nfunctions;
+ unsigned char b_Nfunctions;
struct str_Functionality s_Functions[7];
} str_MainHeader;
typedef struct {
WORD w_Nchannel;
- BYTE b_Interruptible;
+ unsigned char b_Interruptible;
WORD w_NinterruptLogic;
} str_DigitalInputHeader;
typedef struct {
WORD w_HeaderSize;
- BYTE b_Resolution;
- BYTE b_Mode; // in case of Watchdog it is functionality
+ unsigned char b_Resolution;
+ unsigned char b_Mode; // in case of Watchdog it is functionality
WORD w_MinTiming;
- BYTE b_TimeBase;
+ unsigned char b_TimeBase;
} str_TimerDetails;
typedef struct {
typedef struct {
WORD w_Nchannel;
- BYTE b_Resolution;
+ unsigned char b_Resolution;
} str_AnalogOutputHeader;
typedef struct {
WORD w_Nchannel;
WORD w_MinConvertTiming;
WORD w_MinDelayTiming;
- BYTE b_HasDma;
- BYTE b_Resolution;
+ unsigned char b_HasDma;
+ unsigned char b_Resolution;
} str_AnalogInputHeader;
/*****************************************/
void v_EepromClock76(DWORD dw_Address, DWORD dw_RegisterValue);
void v_EepromWaitBusy(WORD w_PCIBoardEepromAddress);
void v_EepromSendCommand76(DWORD dw_Address, DWORD dw_EepromCommand,
- BYTE b_DataLengthInBits);
+ unsigned char b_DataLengthInBits);
void v_EepromCs76Read(DWORD dw_Address, WORD w_offset, PWORD pw_Value);
/*
WORD w_EepromStartAddress)
{
- BYTE b_Counter = 0;
+ unsigned char b_Counter = 0;
- BYTE b_ReadByte = 0;
+ unsigned char b_ReadByte = 0;
- BYTE b_ReadLowByte = 0;
+ unsigned char b_ReadLowByte = 0;
- BYTE b_ReadHighByte = 0;
+ unsigned char b_ReadHighByte = 0;
- BYTE b_SelectedAddressLow = 0;
+ unsigned char b_SelectedAddressLow = 0;
- BYTE b_SelectedAddressHigh = 0;
+ unsigned char b_SelectedAddressHigh = 0;
WORD w_ReadWord = 0;
void v_EepromWaitBusy(WORD w_PCIBoardEepromAddress)
{
- BYTE b_EepromBusy = 0;
+ unsigned char b_EepromBusy = 0;
do
{
| DWORD dw_EepromCommand, |
-| BYTE b_DataLengthInBits) |
+| unsigned char b_DataLengthInBits) |
+---------------------------------------------------------------------------------+
| DWORD dw_EepromCommand : PCI eeprom command to write. |
-| BYTE b_DataLengthInBits : PCI eeprom command data length. |
+| unsigned char b_DataLengthInBits : PCI eeprom command data length. |
+---------------------------------------------------------------------------------+
*/
void v_EepromSendCommand76(DWORD dw_Address, DWORD dw_EepromCommand,
- BYTE b_DataLengthInBits)
+ unsigned char b_DataLengthInBits)
{
char c_BitPos = 0;
// Read nbr of functionality
w_Temp = w_EepromReadWord(w_PCIBoardEepromAddress,
pc_PCIChipInformation, 0x100 + 10);
- s_MainHeader.b_Nfunctions = (BYTE) w_Temp & 0x00FF;
+ s_MainHeader.b_Nfunctions = (unsigned char) w_Temp & 0x00FF;
// Read functionality details
for (i = 0; i < s_MainHeader.b_Nfunctions; i++) {
// Read Type
w_Temp = w_EepromReadWord(w_PCIBoardEepromAddress,
pc_PCIChipInformation, 0x100 + 12 + w_Count);
- s_MainHeader.s_Functions[i].b_Type = (BYTE) w_Temp & 0x3F;
+ s_MainHeader.s_Functions[i].b_Type = (unsigned char) w_Temp & 0x3F;
w_Count = w_Count + 2;
//Read Address
s_MainHeader.s_Functions[i].w_Address =
// interruptible or not
w_Temp = w_EepromReadWord(w_PCIBoardEepromAddress,
pc_PCIChipInformation, 0x100 + w_Address + 8);
- s_Header->b_Interruptible = (BYTE) (w_Temp >> 7) & 0x01;
+ s_Header->b_Interruptible = (unsigned char) (w_Temp >> 7) & 0x01;
// How many interruptible logic
s_Header->w_NinterruptLogic =
//Read Resolution
s_Header->s_TimerDetails[i].b_Resolution =
- (BYTE) (w_Temp >> 10) & 0x3F;
+ (unsigned char) (w_Temp >> 10) & 0x3F;
//Read Mode
s_Header->s_TimerDetails[i].b_Mode =
- (BYTE) (w_Temp >> 4) & 0x3F;
+ (unsigned char) (w_Temp >> 4) & 0x3F;
w_Temp = w_EepromReadWord(w_PCIBoardEepromAddress,
pc_PCIChipInformation,
s_Header->s_TimerDetails[i].w_MinTiming = (w_Temp >> 6) & 0x3FF;
//Read Timebase
- s_Header->s_TimerDetails[i].b_TimeBase = (BYTE) (w_Temp) & 0x3F;
+ s_Header->s_TimerDetails[i].b_TimeBase = (unsigned char) (w_Temp) & 0x3F;
w_Size += s_Header->s_TimerDetails[i].w_HeaderSize;
}
// Resolution for 1st hard component
w_Temp = w_EepromReadWord(w_PCIBoardEepromAddress,
pc_PCIChipInformation, 0x100 + w_Address + 16);
- s_Header->b_Resolution = (BYTE) (w_Temp >> 8) & 0xFF;
+ s_Header->b_Resolution = (unsigned char) (w_Temp >> 8) & 0xFF;
return 0;
}
/*
+----------------------------------------------------------------------------+
| Function's Name : __void__ v_APCI1710_InterruptFunction |
-| (BYTE b_Interrupt, __CPPARGS) |
+| (unsigned char b_Interrupt, __CPPARGS) |
+----------------------------------------------------------------------------+
| Task : APCI-1710 interrupt function |
+----------------------------------------------------------------------------+
-| Input Parameters : BYTE b_Interrupt : Interrupt number |
+| Input Parameters : unsigned char b_Interrupt : Interrupt number |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
void v_APCI1710_Interrupt(int irq, void *d)
{
struct comedi_device *dev = d;
- BYTE b_ModuleCpt = 0;
- BYTE b_InterruptFlag = 0;
- BYTE b_PWMCpt = 0;
- BYTE b_TorCounterCpt = 0;
- BYTE b_PulseIncoderCpt = 0;
+ unsigned char b_ModuleCpt = 0;
+ unsigned char b_InterruptFlag = 0;
+ unsigned char b_PWMCpt = 0;
+ unsigned char b_TorCounterCpt = 0;
+ unsigned char b_PulseIncoderCpt = 0;
UINT ui_16BitValue;
ULONG ul_InterruptLatchReg = 0;
ULONG ul_LatchRegisterValue = 0;
/***********************************/
/* Get the software trigger status */
/***********************************/
- data[1] = (BYTE) ((ul_Command1 >> 1) & 1);
+ data[1] = (unsigned char) ((ul_Command1 >> 1) & 1);
/***********************************/
/* Get the hardware trigger status */
/***********************************/
- data[2] = (BYTE) ((ul_Command1 >> 2) & 1);
+ data[2] = (unsigned char) ((ul_Command1 >> 2) & 1);
/*********************************/
/* Get the software clear status */
/*********************************/
- data[3] = (BYTE) ((ul_Command1 >> 3) & 1);
+ data[3] = (unsigned char) ((ul_Command1 >> 3) & 1);
/***************************/
/* Get the overflow status */
/***************************/
- data[4] = (BYTE) ((ul_Command1 >> 0) & 1);
+ data[4] = (unsigned char) ((ul_Command1 >> 0) & 1);
} // else if (devpriv->b_TimerSelectMode==ADDIDATA_COUNTER)
else if ((devpriv->b_TimerSelectMode != ADDIDATA_TIMER)
&& (devpriv->b_TimerSelectMode != ADDIDATA_WATCHDOG)
| for you call any other function witch access of TTL. |
| APCI16XX_TTL_INITDIRECTION(user inputs for direction) |
+----------------------------------------------------------------------------+
-| Input Parameters : b_InitType = (BYTE) data[0]; |
-| b_Port0Mode = (BYTE) data[1]; |
-| b_Port1Mode = (BYTE) data[2]; |
-| b_Port2Mode = (BYTE) data[3]; |
-| b_Port3Mode = (BYTE) data[4]; |
+| Input Parameters : b_InitType = (unsigned char) data[0]; |
+| b_Port0Mode = (unsigned char) data[1]; |
+| b_Port1Mode = (unsigned char) data[2]; |
+| b_Port2Mode = (unsigned char) data[3]; |
+| b_Port3Mode = (unsigned char) data[4]; |
| ........ |
+----------------------------------------------------------------------------+
| Output Parameters : - |
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Command = 0;
- BYTE b_Cpt = 0;
- BYTE b_NumberOfPort =
- (BYTE) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 8);
+ unsigned char b_Command = 0;
+ unsigned char b_Cpt = 0;
+ unsigned char b_NumberOfPort =
+ (unsigned char) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 8);
/************************/
/* Test the buffer size */
/* Get the command */
/* **************** */
- b_Command = (BYTE) data[0];
+ b_Command = (unsigned char) data[0];
/********************/
/* Test the command */
/***************************************/
if ((b_Command == APCI16XX_TTL_INITDIRECTION)
- && ((BYTE) (insn->n - 1) != b_NumberOfPort)) {
+ && ((unsigned char) (insn->n - 1) != b_NumberOfPort)) {
/*******************/
/* Data size error */
/*******************/
}
if ((b_Command == APCI16XX_TTL_OUTPUTMEMORY)
- && ((BYTE) (insn->n) != 2)) {
+ && ((unsigned char) (insn->n) != 2)) {
/*******************/
/* Data size error */
/*******************/
| APCI16XX_TTL_READCHANNEL |
| b_SelectedPort= CR_RANGE(insn->chanspec); |
| b_InputChannel= CR_CHAN(insn->chanspec); |
-| b_ReadType = (BYTE) data[0]; |
+| b_ReadType = (unsigned char) data[0]; |
| |
| APCI16XX_TTL_READPORT |
| b_SelectedPort= CR_RANGE(insn->chanspec); |
-| b_ReadType = (BYTE) data[0]; |
+| b_ReadType = (unsigned char) data[0]; |
+----------------------------------------------------------------------------+
| Output Parameters : data[0] 0 : Channle is not active |
| 1 : Channle is active |
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Command = 0;
- BYTE b_NumberOfPort =
- (BYTE) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 8);
- BYTE b_SelectedPort = CR_RANGE(insn->chanspec);
- BYTE b_InputChannel = CR_CHAN(insn->chanspec);
- BYTE *pb_Status;
+ unsigned char b_Command = 0;
+ unsigned char b_NumberOfPort =
+ (unsigned char) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 8);
+ unsigned char b_SelectedPort = CR_RANGE(insn->chanspec);
+ unsigned char b_InputChannel = CR_CHAN(insn->chanspec);
+ unsigned char *pb_Status;
DWORD dw_Status;
/************************/
/* Get the command */
/* **************** */
- b_Command = (BYTE) data[0];
+ b_Command = (unsigned char) data[0];
/********************/
/* Test the command */
/**************************/
if (i_ReturnValue >= 0) {
- pb_Status = (PBYTE) & data[0];
+ pb_Status = (unsigned char *) & data[0];
/*******************************/
/* Get the digital inpu status */
/* Save the port value */
/***********************/
- *pb_Status = (BYTE) dw_Status;
+ *pb_Status = (unsigned char) dw_Status;
/***************************************/
/* Test if read channel status command */
int i_APCI16XX_InsnReadTTLIOAllPortValue(struct comedi_device * dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_Command = (BYTE) CR_AREF(insn->chanspec);
+ unsigned char b_Command = (unsigned char) CR_AREF(insn->chanspec);
INT i_ReturnValue = insn->n;
- BYTE b_Cpt = 0;
- BYTE b_NumberOfPort = 0;
+ unsigned char b_Cpt = 0;
+ unsigned char b_NumberOfPort = 0;
unsigned int *pls_ReadData = data;
/********************/
/**********************************/
b_NumberOfPort =
- (BYTE) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 32);
+ (unsigned char) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 32);
if ((b_NumberOfPort * 32) <
devpriv->ps_BoardInfo->i_NbrTTLChannel) {
b_NumberOfPort = b_NumberOfPort + 1;
| APCI16XX_TTL_WRITECHANNEL_ON | APCI16XX_TTL_WRITECHANNEL_OFF |
| b_SelectedPort = CR_RANGE(insn->chanspec); |
| b_OutputChannel= CR_CHAN(insn->chanspec); |
-| b_Command = (BYTE) data[0]; |
+| b_Command = (unsigned char) data[0]; |
| |
| APCI16XX_TTL_WRITEPORT_ON | APCI16XX_TTL_WRITEPORT_OFF |
| b_SelectedPort = CR_RANGE(insn->chanspec); |
-| b_Command = (BYTE) data[0]; |
+| b_Command = (unsigned char) data[0]; |
+----------------------------------------------------------------------------+
| Output Parameters : data[0] : TTL output port 0 to 3 data |
| data[1] : TTL output port 4 to 7 data |
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Command = 0;
- BYTE b_NumberOfPort =
- (BYTE) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 8);
- BYTE b_SelectedPort = CR_RANGE(insn->chanspec);
- BYTE b_OutputChannel = CR_CHAN(insn->chanspec);
+ unsigned char b_Command = 0;
+ unsigned char b_NumberOfPort =
+ (unsigned char) (devpriv->ps_BoardInfo->i_NbrTTLChannel / 8);
+ unsigned char b_SelectedPort = CR_RANGE(insn->chanspec);
+ unsigned char b_OutputChannel = CR_CHAN(insn->chanspec);
DWORD dw_Status = 0;
/************************/
/* Get the command */
/* **************** */
- b_Command = (BYTE) data[0];
+ b_Command = (unsigned char) data[0];
/********************/
/* Test the command */
struct comedi_insn * insn, unsigned int * data)
{
USHORT us_ConvertTiming, us_TmpValue, i;
- BYTE b_Tmp;
+ unsigned char b_Tmp;
// fix convertion time to 10 us
if (!devpriv->ui_EocEosConversionTime) {
int i_APCI3120_CyclicAnalogInput(int mode, struct comedi_device * dev,
struct comedi_subdevice * s)
{
- BYTE b_Tmp;
+ unsigned char b_Tmp;
UINT ui_Tmp, ui_DelayTiming = 0, ui_TimerValue1 = 0, dmalen0 =
0, dmalen1 = 0, ui_TimerValue2 =
0, ui_TimerValue0, ui_ConvertTiming;
unsigned int int_amcc, ui_Check, i;
USHORT us_TmpValue;
- BYTE b_DummyRead;
+ unsigned char b_DummyRead;
struct comedi_subdevice *s = dev->subdevices + 0;
ui_Check = 1;
UINT ui_Timervalue2;
USHORT us_TmpValue;
- BYTE b_Tmp;
+ unsigned char b_Tmp;
if (!data[1])
comedi_error(dev, "config:No timer constant !");
- devpriv->b_Timer2Interrupt = (BYTE) data[2]; // save info whether to enable or disable interrupt
+ devpriv->b_Timer2Interrupt = (unsigned char) data[2]; // save info whether to enable or disable interrupt
ui_Timervalue2 = data[1] / 1000; // convert nano seconds to u seconds
- //this_board->i_hwdrv_InsnConfigTimer(dev, ui_Timervalue2,(BYTE)data[0]);
+ //this_board->i_hwdrv_InsnConfigTimer(dev, ui_Timervalue2,(unsigned char)data[0]);
us_TmpValue = (USHORT) inw(devpriv->iobase + APCI3120_RD_STATUS);
//EL250804: Testing if board APCI3120 have the new Quartz or if it is an APCI3001
UINT ui_Timervalue2 = 0;
USHORT us_TmpValue;
- BYTE b_Tmp;
+ unsigned char b_Tmp;
if ((devpriv->b_Timer2Mode != APCI3120_WATCHDOG)
&& (devpriv->b_Timer2Mode != APCI3120_TIMER)) {
int i_APCI3120_InsnReadTimer(struct comedi_device * dev, struct comedi_subdevice * s,
struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_Tmp;
+ unsigned char b_Tmp;
USHORT us_TmpValue, us_TmpValue_2, us_StatusValue;
if ((devpriv->b_Timer2Mode != APCI3120_WATCHDOG)
#define MAX_ANALOGINPUT_CHANNELS 32
typedef struct {
- BYTE b_Type; /* EOC or EOS */
- BYTE b_InterruptFlag; /* Interrupt use or not */
+ unsigned char b_Type; /* EOC or EOS */
+ unsigned char b_InterruptFlag; /* Interrupt use or not */
UINT ui_ConvertTiming; /* Selection of the convertion time */
- BYTE b_NbrOfChannel; /* Number of channel to read */
+ unsigned char b_NbrOfChannel; /* Number of channel to read */
UINT ui_ChannelList[MAX_ANALOGINPUT_CHANNELS]; /* Number of the channel to be read */
UINT ui_RangeList[MAX_ANALOGINPUT_CHANNELS]; /* Gain of each channel */
struct comedi_insn *insn, unsigned int *data);
//DO
-//int i_APCI3120_WriteDigitalOutput(struct comedi_device *dev, BYTE data);
+//int i_APCI3120_WriteDigitalOutput(struct comedi_device *dev, unsigned char data);
int i_APCI3120_InsnConfigDigitalOutput(struct comedi_device *dev,
struct comedi_subdevice *s, struct comedi_insn *insn,
unsigned int *data);
INT i_Counter = 0;
INT i_WordCounter;
INT i;
- BYTE pb_ReadByte[1];
- BYTE b_ReadLowByte = 0;
- BYTE b_ReadHighByte = 0;
- BYTE b_SelectedAddressLow = 0;
- BYTE b_SelectedAddressHigh = 0;
+ unsigned char pb_ReadByte[1];
+ unsigned char b_ReadLowByte = 0;
+ unsigned char b_ReadHighByte = 0;
+ unsigned char b_SelectedAddressLow = 0;
+ unsigned char b_SelectedAddressHigh = 0;
WORD w_ReadWord = 0;
for (i_WordCounter = 0; i_WordCounter < i_NbOfWordsToRead;
INT i_Initialised;
//UINT ui_InterruptChannelValue[96]; //Buffer
UINT ui_InterruptChannelValue[144]; //Buffer
- BYTE b_StructInitialized;
+ unsigned char b_StructInitialized;
//Begin JK 19.10.2004: APCI-3200 Driver update 0.7.57 -> 0.7.68
unsigned int ui_ScanValueArray[7 + 12]; // 7 is the maximal number of channels
//End JK 19.10.2004: APCI-3200 Driver update 0.7.57 -> 0.7.68
+----------------------------------------------------------------------------+
| Task Converting mode and convert time selection |
+----------------------------------------------------------------------------+
-| Input Parameters : b_SingleDiff = (BYTE) data[1]; |
-| b_TimeBase = (BYTE) data[2]; (0: ns, 1:micros 2:ms)|
+| Input Parameters : b_SingleDiff = (unsigned char) data[1]; |
+| b_TimeBase = (unsigned char) data[2]; (0: ns, 1:micros 2:ms)|
| dw_ReloadValue = (DWORD) data[3]; |
| ........ |
+----------------------------------------------------------------------------+
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_TimeBase = 0;
- BYTE b_SingleDiff = 0;
+ unsigned char b_TimeBase = 0;
+ unsigned char b_SingleDiff = 0;
DWORD dw_ReloadValue = 0;
DWORD dw_TestReloadValue = 0;
/* Get the Singel/Diff flag */
/****************************/
- b_SingleDiff = (BYTE) data[1];
+ b_SingleDiff = (unsigned char) data[1];
/****************************/
/* Get the time base unitiy */
/****************************/
- b_TimeBase = (BYTE) data[2];
+ b_TimeBase = (unsigned char) data[2];
/*************************************/
/* Get the convert time reload value */
+----------------------------------------------------------------------------+
| Task Converting mode and convert time selection |
+----------------------------------------------------------------------------+
-| Input Parameters : b_ConvertMode = (BYTE) data[0]; |
-| b_TimeBase = (BYTE) data[1]; (0: ns, 1:micros 2:ms)|
+| Input Parameters : b_ConvertMode = (unsigned char) data[0]; |
+| b_TimeBase = (unsigned char) data[1]; (0: ns, 1:micros 2:ms)|
| dw_ReloadValue = (DWORD) data[2]; |
| ........ |
+----------------------------------------------------------------------------+
/************************/
if (insn->n >= 1) {
- switch ((BYTE) data[0]) {
+ switch ((unsigned char) data[0]) {
case APCI3XXX_CONFIGURATION:
i_ReturnValue =
i_APCI3XXX_AnalogInputConfigOperatingMode(dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Configuration = (BYTE) CR_RANGE(insn->chanspec);
- BYTE b_Channel = (BYTE) CR_CHAN(insn->chanspec);
+ unsigned char b_Configuration = (unsigned char) CR_RANGE(insn->chanspec);
+ unsigned char b_Channel = (unsigned char) CR_CHAN(insn->chanspec);
DWORD dw_Temp = 0;
DWORD dw_Configuration = 0;
DWORD dw_AcquisitionCpt = 0;
- BYTE b_Interrupt = 0;
+ unsigned char b_Interrupt = 0;
/*************************************/
/* Test if operating mode configured */
void v_APCI3XXX_Interrupt(int irq, void *d)
{
struct comedi_device *dev = d;
- BYTE b_CopyCpt = 0;
+ unsigned char b_CopyCpt = 0;
DWORD dw_Status = 0;
/***************************/
int i_APCI3XXX_InsnWriteAnalogOutput(struct comedi_device * dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_Range = (BYTE) CR_RANGE(insn->chanspec);
- BYTE b_Channel = (BYTE) CR_CHAN(insn->chanspec);
+ unsigned char b_Range = (unsigned char) CR_RANGE(insn->chanspec);
+ unsigned char b_Channel = (unsigned char) CR_CHAN(insn->chanspec);
DWORD dw_Status = 0;
INT i_ReturnValue = insn->n;
| for you call any other function witch access of TTL. |
| APCI3XXX_TTL_INIT_DIRECTION_PORT2(user inputs for direction)|
+----------------------------------------------------------------------------+
-| Input Parameters : b_InitType = (BYTE) data[0]; |
-| b_Port2Mode = (BYTE) data[1]; |
+| Input Parameters : b_InitType = (unsigned char) data[0]; |
+| b_Port2Mode = (unsigned char) data[1]; |
+----------------------------------------------------------------------------+
| Output Parameters : - |
+----------------------------------------------------------------------------+
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Command = 0;
+ unsigned char b_Command = 0;
/************************/
/* Test the buffer size */
/* Get the command */
/* **************** */
- b_Command = (BYTE) data[0];
+ b_Command = (unsigned char) data[0];
/********************/
/* Test the command */
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_ChannelCpt = 0;
+ unsigned char b_ChannelCpt = 0;
DWORD dw_ChannelMask = 0;
DWORD dw_BitMask = 0;
DWORD dw_Status = 0;
int i_APCI3XXX_InsnReadTTLIO(struct comedi_device * dev,
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
- BYTE b_Channel = (BYTE) CR_CHAN(insn->chanspec);
+ unsigned char b_Channel = (unsigned char) CR_CHAN(insn->chanspec);
INT i_ReturnValue = insn->n;
unsigned int *pls_ReadData = data;
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Channel = (BYTE) CR_CHAN(insn->chanspec);
- BYTE b_State = 0;
+ unsigned char b_Channel = (unsigned char) CR_CHAN(insn->chanspec);
+ unsigned char b_State = 0;
DWORD dw_Status = 0;
/************************/
/************************/
if (insn->n >= 1) {
- b_State = (BYTE) data[0];
+ b_State = (unsigned char) data[0];
/***********************/
/* Test if read port 0 */
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Channel = (BYTE) CR_CHAN(insn->chanspec);
+ unsigned char b_Channel = (unsigned char) CR_CHAN(insn->chanspec);
DWORD dw_Temp = 0;
/***************************/
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_ChannelCpt = 0;
+ unsigned char b_ChannelCpt = 0;
DWORD dw_ChannelMask = 0;
DWORD dw_BitMask = 0;
DWORD dw_Status = 0;
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Channel = CR_CHAN(insn->chanspec);
- BYTE b_State = 0;
+ unsigned char b_Channel = CR_CHAN(insn->chanspec);
+ unsigned char b_State = 0;
DWORD dw_Status = 0;
/************************/
/* Get the command */
/*******************/
- b_State = (BYTE) data[0];
+ b_State = (unsigned char) data[0];
/********************************/
/* Read the digital output port */
struct comedi_subdevice * s, struct comedi_insn * insn, unsigned int * data)
{
INT i_ReturnValue = insn->n;
- BYTE b_Channel = CR_CHAN(insn->chanspec);
+ unsigned char b_Channel = CR_CHAN(insn->chanspec);
DWORD dw_Status = 0;
/************************/
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff