Generic Thermal Sysfs driver How To
-=========================
+===================================
Written by Sujith Thomas <sujith.thomas@intel.com>, Zhang Rui <rui.zhang@intel.com>
0. Introduction
-The generic thermal sysfs provides a set of interfaces for thermal zone devices (sensors)
-and thermal cooling devices (fan, processor...) to register with the thermal management
-solution and to be a part of it.
+The generic thermal sysfs provides a set of interfaces for thermal zone
+devices (sensors) and thermal cooling devices (fan, processor...) to register
+with the thermal management solution and to be a part of it.
-This how-to focuses on enabling new thermal zone and cooling devices to participate
-in thermal management.
-This solution is platform independent and any type of thermal zone devices and
-cooling devices should be able to make use of the infrastructure.
+This how-to focuses on enabling new thermal zone and cooling devices to
+participate in thermal management.
+This solution is platform independent and any type of thermal zone devices
+and cooling devices should be able to make use of the infrastructure.
-The main task of the thermal sysfs driver is to expose thermal zone attributes as well
-as cooling device attributes to the user space.
-An intelligent thermal management application can make decisions based on inputs
-from thermal zone attributes (the current temperature and trip point temperature)
-and throttle appropriate devices.
+The main task of the thermal sysfs driver is to expose thermal zone attributes
+as well as cooling device attributes to the user space.
+An intelligent thermal management application can make decisions based on
+inputs from thermal zone attributes (the current temperature and trip point
+temperature) and throttle appropriate devices.
[0-*] denotes any positive number starting from 0
[1-*] denotes any positive number starting from 1
1. thermal sysfs driver interface functions
1.1 thermal zone device interface
-1.1.1 struct thermal_zone_device *thermal_zone_device_register(char *name, int trips,
- void *devdata, struct thermal_zone_device_ops *ops)
-
- This interface function adds a new thermal zone device (sensor) to
- /sys/class/thermal folder as thermal_zone[0-*].
- It tries to bind all the thermal cooling devices registered at the same time.
-
- name: the thermal zone name.
- trips: the total number of trip points this thermal zone supports.
- devdata: device private data
- ops: thermal zone device call-backs.
- .bind: bind the thermal zone device with a thermal cooling device.
- .unbind: unbind the thermal zone device with a thermal cooling device.
- .get_temp: get the current temperature of the thermal zone.
- .get_mode: get the current mode (user/kernel) of the thermal zone.
- "kernel" means thermal management is done in kernel.
- "user" will prevent kernel thermal driver actions upon trip points
- so that user applications can take charge of thermal management.
- .set_mode: set the mode (user/kernel) of the thermal zone.
- .get_trip_type: get the type of certain trip point.
- .get_trip_temp: get the temperature above which the certain trip point
- will be fired.
+1.1.1 struct thermal_zone_device *thermal_zone_device_register(char *name,
+ int trips, void *devdata, struct thermal_zone_device_ops *ops)
+
+ This interface function adds a new thermal zone device (sensor) to
+ /sys/class/thermal folder as thermal_zone[0-*]. It tries to bind all the
+ thermal cooling devices registered at the same time.
+
+ name: the thermal zone name.
+ trips: the total number of trip points this thermal zone supports.
+ devdata: device private data
+ ops: thermal zone device call-backs.
+ .bind: bind the thermal zone device with a thermal cooling device.
+ .unbind: unbind the thermal zone device with a thermal cooling device.
+ .get_temp: get the current temperature of the thermal zone.
+ .get_mode: get the current mode (user/kernel) of the thermal zone.
+ - "kernel" means thermal management is done in kernel.
+ - "user" will prevent kernel thermal driver actions upon trip points
+ so that user applications can take charge of thermal management.
+ .set_mode: set the mode (user/kernel) of the thermal zone.
+ .get_trip_type: get the type of certain trip point.
+ .get_trip_temp: get the temperature above which the certain trip point
+ will be fired.
1.1.2 void thermal_zone_device_unregister(struct thermal_zone_device *tz)
- This interface function removes the thermal zone device.
- It deletes the corresponding entry form /sys/class/thermal folder and unbind all
- the thermal cooling devices it uses.
+ This interface function removes the thermal zone device.
+ It deletes the corresponding entry form /sys/class/thermal folder and
+ unbind all the thermal cooling devices it uses.
1.2 thermal cooling device interface
1.2.1 struct thermal_cooling_device *thermal_cooling_device_register(char *name,
- void *devdata, struct thermal_cooling_device_ops *)
-
- This interface function adds a new thermal cooling device (fan/processor/...) to
- /sys/class/thermal/ folder as cooling_device[0-*].
- It tries to bind itself to all the thermal zone devices register at the same time.
- name: the cooling device name.
- devdata: device private data.
- ops: thermal cooling devices call-backs.
- .get_max_state: get the Maximum throttle state of the cooling device.
- .get_cur_state: get the Current throttle state of the cooling device.
- .set_cur_state: set the Current throttle state of the cooling device.
+ void *devdata, struct thermal_cooling_device_ops *)
+
+ This interface function adds a new thermal cooling device (fan/processor/...)
+ to /sys/class/thermal/ folder as cooling_device[0-*]. It tries to bind itself
+ to all the thermal zone devices register at the same time.
+ name: the cooling device name.
+ devdata: device private data.
+ ops: thermal cooling devices call-backs.
+ .get_max_state: get the Maximum throttle state of the cooling device.
+ .get_cur_state: get the Current throttle state of the cooling device.
+ .set_cur_state: set the Current throttle state of the cooling device.
1.2.2 void thermal_cooling_device_unregister(struct thermal_cooling_device *cdev)
- This interface function remove the thermal cooling device.
- It deletes the corresponding entry form /sys/class/thermal folder and unbind
- itself from all the thermal zone devices using it.
+ This interface function remove the thermal cooling device.
+ It deletes the corresponding entry form /sys/class/thermal folder and
+ unbind itself from all the thermal zone devices using it.
1.3 interface for binding a thermal zone device with a thermal cooling device
1.3.1 int thermal_zone_bind_cooling_device(struct thermal_zone_device *tz,
- int trip, struct thermal_cooling_device *cdev);
+ int trip, struct thermal_cooling_device *cdev);
- This interface function bind a thermal cooling device to the certain trip point
- of a thermal zone device.
- This function is usually called in the thermal zone device .bind callback.
- tz: the thermal zone device
- cdev: thermal cooling device
- trip: indicates which trip point the cooling devices is associated with
- in this thermal zone.
+ This interface function bind a thermal cooling device to the certain trip
+ point of a thermal zone device.
+ This function is usually called in the thermal zone device .bind callback.
+ tz: the thermal zone device
+ cdev: thermal cooling device
+ trip: indicates which trip point the cooling devices is associated with
+ in this thermal zone.
1.3.2 int thermal_zone_unbind_cooling_device(struct thermal_zone_device *tz,
- int trip, struct thermal_cooling_device *cdev);
+ int trip, struct thermal_cooling_device *cdev);
- This interface function unbind a thermal cooling device from the certain trip point
- of a thermal zone device.
- This function is usually called in the thermal zone device .unbind callback.
- tz: the thermal zone device
- cdev: thermal cooling device
- trip: indicates which trip point the cooling devices is associated with
- in this thermal zone.
+ This interface function unbind a thermal cooling device from the certain
+ trip point of a thermal zone device. This function is usually called in
+ the thermal zone device .unbind callback.
+ tz: the thermal zone device
+ cdev: thermal cooling device
+ trip: indicates which trip point the cooling devices is associated with
+ in this thermal zone.
2. sysfs attributes structure
Thermal zone device sys I/F, created once it's registered:
/sys/class/thermal/thermal_zone[0-*]:
- |-----type: Type of the thermal zone
- |-----temp: Current temperature
- |-----mode: Working mode of the thermal zone
- |-----trip_point_[0-*]_temp: Trip point temperature
- |-----trip_point_[0-*]_type: Trip point type
+ |---type: Type of the thermal zone
+ |---temp: Current temperature
+ |---mode: Working mode of the thermal zone
+ |---trip_point_[0-*]_temp: Trip point temperature
+ |---trip_point_[0-*]_type: Trip point type
Thermal cooling device sys I/F, created once it's registered:
/sys/class/thermal/cooling_device[0-*]:
- |-----type : Type of the cooling device(processor/fan/...)
- |-----max_state: Maximum cooling state of the cooling device
- |-----cur_state: Current cooling state of the cooling device
+ |---type: Type of the cooling device(processor/fan/...)
+ |---max_state: Maximum cooling state of the cooling device
+ |---cur_state: Current cooling state of the cooling device
-These two dynamic attributes are created/removed in pairs.
-They represent the relationship between a thermal zone and its associated cooling device.
-They are created/removed for each
-thermal_zone_bind_cooling_device/thermal_zone_unbind_cooling_device successful execution.
+Then next two dynamic attributes are created/removed in pairs. They represent
+the relationship between a thermal zone and its associated cooling device.
+They are created/removed for each successful execution of
+thermal_zone_bind_cooling_device/thermal_zone_unbind_cooling_device.
-/sys/class/thermal/thermal_zone[0-*]
- |-----cdev[0-*]: The [0-*]th cooling device in the current thermal zone
- |-----cdev[0-*]_trip_point: Trip point that cdev[0-*] is associated with
+/sys/class/thermal/thermal_zone[0-*]:
+ |---cdev[0-*]: [0-*]th cooling device in current thermal zone
+ |---cdev[0-*]_trip_point: Trip point that cdev[0-*] is associated with
Besides the thermal zone device sysfs I/F and cooling device sysfs I/F,
-the generic thermal driver also creates a hwmon sysfs I/F for each _type_ of
-thermal zone device. E.g. the generic thermal driver registers one hwmon class device
-and build the associated hwmon sysfs I/F for all the registered ACPI thermal zones.
+the generic thermal driver also creates a hwmon sysfs I/F for each _type_
+of thermal zone device. E.g. the generic thermal driver registers one hwmon
+class device and build the associated hwmon sysfs I/F for all the registered
+ACPI thermal zones.
+
/sys/class/hwmon/hwmon[0-*]:
- |-----name: The type of the thermal zone devices.
- |-----temp[1-*]_input: The current temperature of thermal zone [1-*].
- |-----temp[1-*]_critical: The critical trip point of thermal zone [1-*].
+ |---name: The type of the thermal zone devices
+ |---temp[1-*]_input: The current temperature of thermal zone [1-*]
+ |---temp[1-*]_critical: The critical trip point of thermal zone [1-*]
+
Please read Documentation/hwmon/sysfs-interface for additional information.
***************************
* Thermal zone attributes *
***************************
-type Strings which represent the thermal zone type.
- This is given by thermal zone driver as part of registration.
- Eg: "acpitz" indicates it's an ACPI thermal device.
- In order to keep it consistent with hwmon sys attribute,
- this should be a short, lowercase string,
- not containing spaces nor dashes.
- RO
- Required
-
-temp Current temperature as reported by thermal zone (sensor)
- Unit: millidegree Celsius
- RO
- Required
-
-mode One of the predefined values in [kernel, user]
- This file gives information about the algorithm
- that is currently managing the thermal zone.
- It can be either default kernel based algorithm
- or user space application.
- RW
- Optional
- kernel = Thermal management in kernel thermal zone driver.
- user = Preventing kernel thermal zone driver actions upon
- trip points so that user application can take full
- charge of the thermal management.
-
-trip_point_[0-*]_temp The temperature above which trip point will be fired
- Unit: millidegree Celsius
- RO
- Optional
-
-trip_point_[0-*]_type Strings which indicate the type of the trip point
- E.g. it can be one of critical, hot, passive,
- active[0-*] for ACPI thermal zone.
- RO
- Optional
-
-cdev[0-*] Sysfs link to the thermal cooling device node where the sys I/F
- for cooling device throttling control represents.
- RO
- Optional
-
-cdev[0-*]_trip_point The trip point with which cdev[0-*] is associated in this thermal zone
- -1 means the cooling device is not associated with any trip point.
- RO
- Optional
-
-******************************
-* Cooling device attributes *
-******************************
-
-type String which represents the type of device
- eg: For generic ACPI: this should be "Fan",
- "Processor" or "LCD"
- eg. For memory controller device on intel_menlow platform:
- this should be "Memory controller"
- RO
- Required
-
-max_state The maximum permissible cooling state of this cooling device.
- RO
- Required
-
-cur_state The current cooling state of this cooling device.
- the value can any integer numbers between 0 and max_state,
- cur_state == 0 means no cooling
- cur_state == max_state means the maximum cooling.
- RW
- Required
+type
+ Strings which represent the thermal zone type.
+ This is given by thermal zone driver as part of registration.
+ E.g: "acpitz" indicates it's an ACPI thermal device.
+ In order to keep it consistent with hwmon sys attribute; this should
+ be a short, lowercase string, not containing spaces nor dashes.
+ RO, Required
+
+temp
+ Current temperature as reported by thermal zone (sensor).
+ Unit: millidegree Celsius
+ RO, Required
+
+mode
+ One of the predefined values in [kernel, user].
+ This file gives information about the algorithm that is currently
+ managing the thermal zone. It can be either default kernel based
+ algorithm or user space application.
+ kernel = Thermal management in kernel thermal zone driver.
+ user = Preventing kernel thermal zone driver actions upon
+ trip points so that user application can take full
+ charge of the thermal management.
+ RW, Optional
+
+trip_point_[0-*]_temp
+ The temperature above which trip point will be fired.
+ Unit: millidegree Celsius
+ RO, Optional
+
+trip_point_[0-*]_type
+ Strings which indicate the type of the trip point.
+ E.g. it can be one of critical, hot, passive, active[0-*] for ACPI
+ thermal zone.
+ RO, Optional
+
+cdev[0-*]
+ Sysfs link to the thermal cooling device node where the sys I/F
+ for cooling device throttling control represents.
+ RO, Optional
+
+cdev[0-*]_trip_point
+ The trip point with which cdev[0-*] is associated in this thermal
+ zone; -1 means the cooling device is not associated with any trip
+ point.
+ RO, Optional
+
+passive
+ Attribute is only present for zones in which the passive cooling
+ policy is not supported by native thermal driver. Default is zero
+ and can be set to a temperature (in millidegrees) to enable a
+ passive trip point for the zone. Activation is done by polling with
+ an interval of 1 second.
+ Unit: millidegrees Celsius
+ RW, Optional
+
+*****************************
+* Cooling device attributes *
+*****************************
+
+type
+ String which represents the type of device, e.g:
+ - for generic ACPI: should be "Fan", "Processor" or "LCD"
+ - for memory controller device on intel_menlow platform:
+ should be "Memory controller".
+ RO, Required
+
+max_state
+ The maximum permissible cooling state of this cooling device.
+ RO, Required
+
+cur_state
+ The current cooling state of this cooling device.
+ The value can any integer numbers between 0 and max_state:
+ - cur_state == 0 means no cooling
+ - cur_state == max_state means the maximum cooling.
+ RW, Required
3. A simple implementation
-ACPI thermal zone may support multiple trip points like critical/hot/passive/active.
-If an ACPI thermal zone supports critical, passive, active[0] and active[1] at the same time,
-it may register itself as a thermal_zone_device (thermal_zone1) with 4 trip points in all.
-It has one processor and one fan, which are both registered as thermal_cooling_device.
-If the processor is listed in _PSL method, and the fan is listed in _AL0 method,
-the sys I/F structure will be built like this:
+ACPI thermal zone may support multiple trip points like critical, hot,
+passive, active. If an ACPI thermal zone supports critical, passive,
+active[0] and active[1] at the same time, it may register itself as a
+thermal_zone_device (thermal_zone1) with 4 trip points in all.
+It has one processor and one fan, which are both registered as
+thermal_cooling_device.
+
+If the processor is listed in _PSL method, and the fan is listed in _AL0
+method, the sys I/F structure will be built like this:
/sys/class/thermal:
|thermal_zone1:
- |-----type: acpitz
- |-----temp: 37000
- |-----mode: kernel
- |-----trip_point_0_temp: 100000
- |-----trip_point_0_type: critical
- |-----trip_point_1_temp: 80000
- |-----trip_point_1_type: passive
- |-----trip_point_2_temp: 70000
- |-----trip_point_2_type: active0
- |-----trip_point_3_temp: 60000
- |-----trip_point_3_type: active1
- |-----cdev0: --->/sys/class/thermal/cooling_device0
- |-----cdev0_trip_point: 1 /* cdev0 can be used for passive */
- |-----cdev1: --->/sys/class/thermal/cooling_device3
- |-----cdev1_trip_point: 2 /* cdev1 can be used for active[0]*/
+ |---type: acpitz
+ |---temp: 37000
+ |---mode: kernel
+ |---trip_point_0_temp: 100000
+ |---trip_point_0_type: critical
+ |---trip_point_1_temp: 80000
+ |---trip_point_1_type: passive
+ |---trip_point_2_temp: 70000
+ |---trip_point_2_type: active0
+ |---trip_point_3_temp: 60000
+ |---trip_point_3_type: active1
+ |---cdev0: --->/sys/class/thermal/cooling_device0
+ |---cdev0_trip_point: 1 /* cdev0 can be used for passive */
+ |---cdev1: --->/sys/class/thermal/cooling_device3
+ |---cdev1_trip_point: 2 /* cdev1 can be used for active[0]*/
|cooling_device0:
- |-----type: Processor
- |-----max_state: 8
- |-----cur_state: 0
+ |---type: Processor
+ |---max_state: 8
+ |---cur_state: 0
|cooling_device3:
- |-----type: Fan
- |-----max_state: 2
- |-----cur_state: 0
+ |---type: Fan
+ |---max_state: 2
+ |---cur_state: 0
/sys/class/hwmon:
|hwmon0:
- |-----name: acpitz
- |-----temp1_input: 37000
- |-----temp1_crit: 100000
+ |---name: acpitz
+ |---temp1_input: 37000
+ |---temp1_crit: 100000
CFQ_CFQQ_FLAG_slice_new, /* no requests dispatched in slice */
CFQ_CFQQ_FLAG_sync, /* synchronous queue */
CFQ_CFQQ_FLAG_coop, /* has done a coop jump of the queue */
+ CFQ_CFQQ_FLAG_coop_preempt, /* coop preempt */
};
#define CFQ_CFQQ_FNS(name) \
CFQ_CFQQ_FNS(slice_new);
CFQ_CFQQ_FNS(sync);
CFQ_CFQQ_FNS(coop);
+CFQ_CFQQ_FNS(coop_preempt);
#undef CFQ_CFQQ_FNS
#define cfq_log_cfqq(cfqd, cfqq, fmt, args...) \
{
if (!cfqq) {
cfqq = cfq_get_next_queue(cfqd);
- if (cfqq)
+ if (cfqq && !cfq_cfqq_coop_preempt(cfqq))
cfq_clear_cfqq_coop(cfqq);
}
+ if (cfqq)
+ cfq_clear_cfqq_coop_preempt(cfqq);
+
__cfq_set_active_queue(cfqd, cfqq);
return cfqq;
}
* it's a metadata request and the current queue is doing regular IO.
*/
if (rq_is_meta(rq) && !cfqq->meta_pending)
- return false;
+ return true;
/*
* Allow an RT request to pre-empt an ongoing non-RT cfqq timeslice.
* if this request is as-good as one we would expect from the
* current cfqq, let it preempt
*/
- if (cfq_rq_close(cfqd, rq))
+ if (cfq_rq_close(cfqd, rq) && (!cfq_cfqq_coop(new_cfqq) ||
+ cfqd->busy_queues == 1)) {
+ /*
+ * Mark new queue coop_preempt, so its coop flag will not be
+ * cleared when new queue gets scheduled at the very first time
+ */
+ cfq_mark_cfqq_coop_preempt(new_cfqq);
+ cfq_mark_cfqq_coop(new_cfqq);
return true;
+ }
return false;
}
return -EINVAL;
}
- return data;
+ /* _PTP returns 0 on success, nonzero otherwise */
+ if (data)
+ return -EINVAL;
+
+ return 0;
}
static ssize_t set_trip(struct device *dev, struct device_attribute *devattr,
struct list_head *node, *next;
char strbuf[5];
char str[5] = "";
- int len = count;
+ unsigned int len = count;
struct acpi_device *found_dev = NULL;
if (len > 4)
.notifier_call = acpi_cpu_soft_notify,
};
-static int acpi_processor_add(struct acpi_device *device)
+static int __cpuinit acpi_processor_add(struct acpi_device *device)
{
struct acpi_processor *pr = NULL;
int result = 0;
int result = 0;
struct acpi_processor_throttling *pthrottling;
+ if (!pr)
+ return -EINVAL;
+
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
"pblk_address[0x%08x] duty_offset[%d] duty_width[%d]\n",
pr->throttling.address,
pr->throttling.duty_offset,
pr->throttling.duty_width));
- if (!pr)
- return -EINVAL;
-
/*
* Evaluate _PTC, _TSS and _TPC
* They must all be present or none of them can be used.
u32 state = 0;
- if (!dev || count + 1 > sizeof str)
+ if (!dev || count >= sizeof(str))
return -EINVAL;
if (copy_from_user(str, buffer, count))
int i;
- if (!dev || !dev->brightness || count + 1 > sizeof str)
+ if (!dev || !dev->brightness || count >= sizeof(str))
return -EINVAL;
if (copy_from_user(str, buffer, count))
unsigned long long opt, options;
- if (!video || count + 1 > sizeof str)
+ if (!video || count >= sizeof(str))
return -EINVAL;
status = acpi_video_bus_POST_options(video, &options);
unsigned long opt;
- if (!video || count + 1 > sizeof str)
+ if (!video || count >= sizeof(str))
return -EINVAL;
if (copy_from_user(str, buffer, count))
},
.driver_data = "20071026", /* yyyymmdd */
},
+ /*
+ * All BIOS versions for the MSI K9A2 Platinum (MS-7376)
+ * support 64bit DMA.
+ *
+ * BIOS versions earlier than 1.5 had the Manufacturer DMI
+ * fields as "MICRO-STAR INTERANTIONAL CO.,LTD".
+ * This spelling mistake was fixed in BIOS version 1.5, so
+ * 1.5 and later have the Manufacturer as
+ * "MICRO-STAR INTERNATIONAL CO.,LTD".
+ * So try to match on DMI_BOARD_VENDOR of "MICRO-STAR INTER".
+ *
+ * BIOS versions earlier than 1.9 had a Board Product Name
+ * DMI field of "MS-7376". This was changed to be
+ * "K9A2 Platinum (MS-7376)" in version 1.9, but we can still
+ * match on DMI_BOARD_NAME of "MS-7376".
+ */
+ {
+ .ident = "MSI K9A2 Platinum",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR,
+ "MICRO-STAR INTER"),
+ DMI_MATCH(DMI_BOARD_NAME, "MS-7376"),
+ },
+ },
{ }
};
const struct dmi_system_id *match;
!match)
return false;
+ if (!match->driver_data)
+ goto enable_64bit;
+
dmi_get_date(DMI_BIOS_DATE, &year, &month, &date);
snprintf(buf, sizeof(buf), "%04d%02d%02d", year, month, date);
- if (strcmp(buf, match->driver_data) >= 0) {
- dev_printk(KERN_WARNING, &pdev->dev, "%s: enabling 64bit DMA\n",
- match->ident);
- return true;
- } else {
+ if (strcmp(buf, match->driver_data) >= 0)
+ goto enable_64bit;
+ else {
dev_printk(KERN_WARNING, &pdev->dev, "%s: BIOS too old, "
"forcing 32bit DMA, update BIOS\n", match->ident);
return false;
}
+
+enable_64bit:
+ dev_printk(KERN_WARNING, &pdev->dev, "%s: enabling 64bit DMA\n",
+ match->ident);
+ return true;
}
static bool ahci_broken_system_poweroff(struct pci_dev *pdev)
*/
void ata_qc_free(struct ata_queued_cmd *qc)
{
- struct ata_port *ap = qc->ap;
+ struct ata_port *ap;
unsigned int tag;
WARN_ON_ONCE(qc == NULL); /* ata_qc_from_tag _might_ return NULL */
+ ap = qc->ap;
qc->flags = 0;
tag = qc->tag;
void __ata_qc_complete(struct ata_queued_cmd *qc)
{
- struct ata_port *ap = qc->ap;
- struct ata_link *link = qc->dev->link;
+ struct ata_port *ap;
+ struct ata_link *link;
WARN_ON_ONCE(qc == NULL); /* ata_qc_from_tag _might_ return NULL */
WARN_ON_ONCE(!(qc->flags & ATA_QCFLAG_ACTIVE));
+ ap = qc->ap;
+ link = qc->dev->link;
if (likely(qc->flags & ATA_QCFLAG_DMAMAP))
ata_sg_clean(qc);
{ PCI_VDEVICE(VIA, 0x7372), vt6420 },
{ PCI_VDEVICE(VIA, 0x5287), vt8251 }, /* 2 sata chnls (Master/Slave) */
{ PCI_VDEVICE(VIA, 0x9000), vt8251 },
- { PCI_VDEVICE(VIA, 0x9040), vt8251 },
{ } /* terminate list */
};
goto out;
/* Try to set up FBC with a reasonable compressed buffer size */
- if (IS_MOBILE(dev) && (IS_I9XX(dev) || IS_I965G(dev) || IS_GM45(dev)) &&
- i915_powersave) {
+ if (I915_HAS_FBC(dev) && i915_powersave) {
int cfb_size;
/* Try to get an 8M buffer... */
u32 saveVBLANK_A;
u32 saveVSYNC_A;
u32 saveBCLRPAT_A;
+ u32 saveTRANS_HTOTAL_A;
+ u32 saveTRANS_HBLANK_A;
+ u32 saveTRANS_HSYNC_A;
+ u32 saveTRANS_VTOTAL_A;
+ u32 saveTRANS_VBLANK_A;
+ u32 saveTRANS_VSYNC_A;
u32 savePIPEASTAT;
u32 saveDSPASTRIDE;
u32 saveDSPASIZE;
u32 saveDSPASURF;
u32 saveDSPATILEOFF;
u32 savePFIT_PGM_RATIOS;
+ u32 saveBLC_HIST_CTL;
u32 saveBLC_PWM_CTL;
u32 saveBLC_PWM_CTL2;
+ u32 saveBLC_CPU_PWM_CTL;
+ u32 saveBLC_CPU_PWM_CTL2;
u32 saveFPB0;
u32 saveFPB1;
u32 saveDPLL_B;
u32 saveVBLANK_B;
u32 saveVSYNC_B;
u32 saveBCLRPAT_B;
+ u32 saveTRANS_HTOTAL_B;
+ u32 saveTRANS_HBLANK_B;
+ u32 saveTRANS_HSYNC_B;
+ u32 saveTRANS_VTOTAL_B;
+ u32 saveTRANS_VBLANK_B;
+ u32 saveTRANS_VSYNC_B;
u32 savePIPEBSTAT;
u32 saveDSPBSTRIDE;
u32 saveDSPBSIZE;
u32 savePFIT_CONTROL;
u32 save_palette_a[256];
u32 save_palette_b[256];
+ u32 saveDPFC_CB_BASE;
u32 saveFBC_CFB_BASE;
u32 saveFBC_LL_BASE;
u32 saveFBC_CONTROL;
u32 saveIER;
u32 saveIIR;
u32 saveIMR;
+ u32 saveDEIER;
+ u32 saveDEIMR;
+ u32 saveGTIER;
+ u32 saveGTIMR;
+ u32 saveFDI_RXA_IMR;
+ u32 saveFDI_RXB_IMR;
u32 saveCACHE_MODE_0;
u32 saveD_STATE;
u32 saveDSPCLK_GATE_D;
u32 savePIPEB_DP_LINK_M;
u32 savePIPEA_DP_LINK_N;
u32 savePIPEB_DP_LINK_N;
+ u32 saveFDI_RXA_CTL;
+ u32 saveFDI_TXA_CTL;
+ u32 saveFDI_RXB_CTL;
+ u32 saveFDI_TXB_CTL;
+ u32 savePFA_CTL_1;
+ u32 savePFB_CTL_1;
+ u32 savePFA_WIN_SZ;
+ u32 savePFB_WIN_SZ;
+ u32 savePFA_WIN_POS;
+ u32 savePFB_WIN_POS;
struct {
struct drm_mm gtt_space;
struct drm_i915_gem_phys_object *phys_objs[I915_MAX_PHYS_OBJECT];
} mm;
struct sdvo_device_mapping sdvo_mappings[2];
+ /* indicate whether the LVDS_BORDER should be enabled or not */
+ unsigned int lvds_border_bits;
/* Reclocking support */
bool render_reclock_avail;
#define HAS_FW_BLC(dev) (IS_I9XX(dev) || IS_G4X(dev) || IS_IGDNG(dev))
#define HAS_PIPE_CXSR(dev) (IS_G4X(dev) || IS_IGDNG(dev))
-#define I915_HAS_FBC(dev) (IS_MOBILE(dev) && (IS_I9XX(dev) || IS_I965G(dev)))
+#define I915_HAS_FBC(dev) (IS_MOBILE(dev) && \
+ (IS_I9XX(dev) || IS_GM45(dev)) && \
+ !IS_IGD(dev) && \
+ !IS_IGDNG(dev))
#define PRIMARY_RINGBUFFER_SIZE (128*1024)
#define LVDS_PORT_EN (1 << 31)
/* Selects pipe B for LVDS data. Must be set on pre-965. */
#define LVDS_PIPEB_SELECT (1 << 30)
+/* Enable border for unscaled (or aspect-scaled) display */
+#define LVDS_BORDER_ENABLE (1 << 15)
/*
* Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
* pixel.
#define BACKLIGHT_DUTY_CYCLE_SHIFT (0)
#define BACKLIGHT_DUTY_CYCLE_MASK (0xffff)
+#define BLC_HIST_CTL 0x61260
+
/* TV port control */
#define TV_CTL 0x68000
/** Enables the TV encoder */
#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
#define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1)
#define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0)
+#define PIPE_BPC_MASK (7 << 5) /* Ironlake */
+#define PIPE_8BPC (0 << 5)
+#define PIPE_10BPC (1 << 5)
+#define PIPE_6BPC (2 << 5)
+#define PIPE_12BPC (3 << 5)
#define DSPARB 0x70030
#define DSPARB_CSTART_MASK (0x7f << 7)
#define DSPARB_AEND_SHIFT 0
#define DSPFW1 0x70034
+#define DSPFW_SR_SHIFT 23
+#define DSPFW_CURSORB_SHIFT 16
+#define DSPFW_PLANEB_SHIFT 8
#define DSPFW2 0x70038
+#define DSPFW_CURSORA_MASK 0x00003f00
+#define DSPFW_CURSORA_SHIFT 16
#define DSPFW3 0x7003c
+#define DSPFW_HPLL_SR_EN (1<<31)
+#define DSPFW_CURSOR_SR_SHIFT 24
#define IGD_SELF_REFRESH_EN (1<<30)
/* FIFO watermark sizes etc */
+#define G4X_FIFO_LINE_SIZE 64
#define I915_FIFO_LINE_SIZE 64
#define I830_FIFO_LINE_SIZE 32
+
+#define G4X_FIFO_SIZE 127
#define I945_FIFO_SIZE 127 /* 945 & 965 */
#define I915_FIFO_SIZE 95
#define I855GM_FIFO_SIZE 127 /* In cachelines */
#define I830_FIFO_SIZE 95
+
+#define G4X_MAX_WM 0x3f
#define I915_MAX_WM 0x3f
#define IGD_DISPLAY_FIFO 512 /* in 64byte unit */
#define PFA_CTL_1 0x68080
#define PFB_CTL_1 0x68880
#define PF_ENABLE (1<<31)
+#define PF_FILTER_MASK (3<<23)
+#define PF_FILTER_PROGRAMMED (0<<23)
+#define PF_FILTER_MED_3x3 (1<<23)
+#define PF_FILTER_EDGE_ENHANCE (2<<23)
+#define PF_FILTER_EDGE_SOFTEN (3<<23)
#define PFA_WIN_SZ 0x68074
#define PFB_WIN_SZ 0x68874
#define PFA_WIN_POS 0x68070
#define DREF_CPU_SOURCE_OUTPUT_MASK (3<<13)
#define DREF_SSC_SOURCE_DISABLE (0<<11)
#define DREF_SSC_SOURCE_ENABLE (2<<11)
-#define DREF_SSC_SOURCE_MASK (2<<11)
+#define DREF_SSC_SOURCE_MASK (3<<11)
#define DREF_NONSPREAD_SOURCE_DISABLE (0<<9)
#define DREF_NONSPREAD_CK505_ENABLE (1<<9)
#define DREF_NONSPREAD_SOURCE_ENABLE (2<<9)
-#define DREF_NONSPREAD_SOURCE_MASK (2<<9)
+#define DREF_NONSPREAD_SOURCE_MASK (3<<9)
#define DREF_SUPERSPREAD_SOURCE_DISABLE (0<<7)
#define DREF_SUPERSPREAD_SOURCE_ENABLE (2<<7)
#define DREF_SSC4_DOWNSPREAD (0<<6)
static bool i915_pipe_enabled(struct drm_device *dev, enum pipe pipe)
{
struct drm_i915_private *dev_priv = dev->dev_private;
+ u32 dpll_reg;
- if (pipe == PIPE_A)
- return (I915_READ(DPLL_A) & DPLL_VCO_ENABLE);
- else
- return (I915_READ(DPLL_B) & DPLL_VCO_ENABLE);
+ if (IS_IGDNG(dev)) {
+ dpll_reg = (pipe == PIPE_A) ? PCH_DPLL_A: PCH_DPLL_B;
+ } else {
+ dpll_reg = (pipe == PIPE_A) ? DPLL_A: DPLL_B;
+ }
+
+ return (I915_READ(dpll_reg) & DPLL_VCO_ENABLE);
}
static void i915_save_palette(struct drm_device *dev, enum pipe pipe)
if (!i915_pipe_enabled(dev, pipe))
return;
+ if (IS_IGDNG(dev))
+ reg = (pipe == PIPE_A) ? LGC_PALETTE_A : LGC_PALETTE_B;
+
if (pipe == PIPE_A)
array = dev_priv->save_palette_a;
else
if (!i915_pipe_enabled(dev, pipe))
return;
+ if (IS_IGDNG(dev))
+ reg = (pipe == PIPE_A) ? LGC_PALETTE_A : LGC_PALETTE_B;
+
if (pipe == PIPE_A)
array = dev_priv->save_palette_a;
else
/* Pipe & plane A info */
dev_priv->savePIPEACONF = I915_READ(PIPEACONF);
dev_priv->savePIPEASRC = I915_READ(PIPEASRC);
- dev_priv->saveFPA0 = I915_READ(FPA0);
- dev_priv->saveFPA1 = I915_READ(FPA1);
- dev_priv->saveDPLL_A = I915_READ(DPLL_A);
- if (IS_I965G(dev))
+ if (IS_IGDNG(dev)) {
+ dev_priv->saveFPA0 = I915_READ(PCH_FPA0);
+ dev_priv->saveFPA1 = I915_READ(PCH_FPA1);
+ dev_priv->saveDPLL_A = I915_READ(PCH_DPLL_A);
+ } else {
+ dev_priv->saveFPA0 = I915_READ(FPA0);
+ dev_priv->saveFPA1 = I915_READ(FPA1);
+ dev_priv->saveDPLL_A = I915_READ(DPLL_A);
+ }
+ if (IS_I965G(dev) && !IS_IGDNG(dev))
dev_priv->saveDPLL_A_MD = I915_READ(DPLL_A_MD);
dev_priv->saveHTOTAL_A = I915_READ(HTOTAL_A);
dev_priv->saveHBLANK_A = I915_READ(HBLANK_A);
dev_priv->saveVTOTAL_A = I915_READ(VTOTAL_A);
dev_priv->saveVBLANK_A = I915_READ(VBLANK_A);
dev_priv->saveVSYNC_A = I915_READ(VSYNC_A);
- dev_priv->saveBCLRPAT_A = I915_READ(BCLRPAT_A);
+ if (!IS_IGDNG(dev))
+ dev_priv->saveBCLRPAT_A = I915_READ(BCLRPAT_A);
+
+ if (IS_IGDNG(dev)) {
+ dev_priv->saveFDI_TXA_CTL = I915_READ(FDI_TXA_CTL);
+ dev_priv->saveFDI_RXA_CTL = I915_READ(FDI_RXA_CTL);
+
+ dev_priv->savePFA_CTL_1 = I915_READ(PFA_CTL_1);
+ dev_priv->savePFA_WIN_SZ = I915_READ(PFA_WIN_SZ);
+ dev_priv->savePFA_WIN_POS = I915_READ(PFA_WIN_POS);
+
+ dev_priv->saveTRANS_HTOTAL_A = I915_READ(TRANS_HTOTAL_A);
+ dev_priv->saveTRANS_HBLANK_A = I915_READ(TRANS_HBLANK_A);
+ dev_priv->saveTRANS_HSYNC_A = I915_READ(TRANS_HSYNC_A);
+ dev_priv->saveTRANS_VTOTAL_A = I915_READ(TRANS_VTOTAL_A);
+ dev_priv->saveTRANS_VBLANK_A = I915_READ(TRANS_VBLANK_A);
+ dev_priv->saveTRANS_VSYNC_A = I915_READ(TRANS_VSYNC_A);
+ }
dev_priv->saveDSPACNTR = I915_READ(DSPACNTR);
dev_priv->saveDSPASTRIDE = I915_READ(DSPASTRIDE);
/* Pipe & plane B info */
dev_priv->savePIPEBCONF = I915_READ(PIPEBCONF);
dev_priv->savePIPEBSRC = I915_READ(PIPEBSRC);
- dev_priv->saveFPB0 = I915_READ(FPB0);
- dev_priv->saveFPB1 = I915_READ(FPB1);
- dev_priv->saveDPLL_B = I915_READ(DPLL_B);
- if (IS_I965G(dev))
+ if (IS_IGDNG(dev)) {
+ dev_priv->saveFPB0 = I915_READ(PCH_FPB0);
+ dev_priv->saveFPB1 = I915_READ(PCH_FPB1);
+ dev_priv->saveDPLL_B = I915_READ(PCH_DPLL_B);
+ } else {
+ dev_priv->saveFPB0 = I915_READ(FPB0);
+ dev_priv->saveFPB1 = I915_READ(FPB1);
+ dev_priv->saveDPLL_B = I915_READ(DPLL_B);
+ }
+ if (IS_I965G(dev) && !IS_IGDNG(dev))
dev_priv->saveDPLL_B_MD = I915_READ(DPLL_B_MD);
dev_priv->saveHTOTAL_B = I915_READ(HTOTAL_B);
dev_priv->saveHBLANK_B = I915_READ(HBLANK_B);
dev_priv->saveVTOTAL_B = I915_READ(VTOTAL_B);
dev_priv->saveVBLANK_B = I915_READ(VBLANK_B);
dev_priv->saveVSYNC_B = I915_READ(VSYNC_B);
- dev_priv->saveBCLRPAT_A = I915_READ(BCLRPAT_A);
+ if (!IS_IGDNG(dev))
+ dev_priv->saveBCLRPAT_B = I915_READ(BCLRPAT_B);
+
+ if (IS_IGDNG(dev)) {
+ dev_priv->saveFDI_TXB_CTL = I915_READ(FDI_TXB_CTL);
+ dev_priv->saveFDI_RXB_CTL = I915_READ(FDI_RXB_CTL);
+
+ dev_priv->savePFB_CTL_1 = I915_READ(PFB_CTL_1);
+ dev_priv->savePFB_WIN_SZ = I915_READ(PFB_WIN_SZ);
+ dev_priv->savePFB_WIN_POS = I915_READ(PFB_WIN_POS);
+
+ dev_priv->saveTRANS_HTOTAL_B = I915_READ(TRANS_HTOTAL_B);
+ dev_priv->saveTRANS_HBLANK_B = I915_READ(TRANS_HBLANK_B);
+ dev_priv->saveTRANS_HSYNC_B = I915_READ(TRANS_HSYNC_B);
+ dev_priv->saveTRANS_VTOTAL_B = I915_READ(TRANS_VTOTAL_B);
+ dev_priv->saveTRANS_VBLANK_B = I915_READ(TRANS_VBLANK_B);
+ dev_priv->saveTRANS_VSYNC_B = I915_READ(TRANS_VSYNC_B);
+ }
dev_priv->saveDSPBCNTR = I915_READ(DSPBCNTR);
dev_priv->saveDSPBSTRIDE = I915_READ(DSPBSTRIDE);
static void i915_restore_modeset_reg(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
+ int dpll_a_reg, fpa0_reg, fpa1_reg;
+ int dpll_b_reg, fpb0_reg, fpb1_reg;
if (drm_core_check_feature(dev, DRIVER_MODESET))
return;
+ if (IS_IGDNG(dev)) {
+ dpll_a_reg = PCH_DPLL_A;
+ dpll_b_reg = PCH_DPLL_B;
+ fpa0_reg = PCH_FPA0;
+ fpb0_reg = PCH_FPB0;
+ fpa1_reg = PCH_FPA1;
+ fpb1_reg = PCH_FPB1;
+ } else {
+ dpll_a_reg = DPLL_A;
+ dpll_b_reg = DPLL_B;
+ fpa0_reg = FPA0;
+ fpb0_reg = FPB0;
+ fpa1_reg = FPA1;
+ fpb1_reg = FPB1;
+ }
+
/* Pipe & plane A info */
/* Prime the clock */
if (dev_priv->saveDPLL_A & DPLL_VCO_ENABLE) {
- I915_WRITE(DPLL_A, dev_priv->saveDPLL_A &
+ I915_WRITE(dpll_a_reg, dev_priv->saveDPLL_A &
~DPLL_VCO_ENABLE);
DRM_UDELAY(150);
}
- I915_WRITE(FPA0, dev_priv->saveFPA0);
- I915_WRITE(FPA1, dev_priv->saveFPA1);
+ I915_WRITE(fpa0_reg, dev_priv->saveFPA0);
+ I915_WRITE(fpa1_reg, dev_priv->saveFPA1);
/* Actually enable it */
- I915_WRITE(DPLL_A, dev_priv->saveDPLL_A);
+ I915_WRITE(dpll_a_reg, dev_priv->saveDPLL_A);
DRM_UDELAY(150);
- if (IS_I965G(dev))
+ if (IS_I965G(dev) && !IS_IGDNG(dev))
I915_WRITE(DPLL_A_MD, dev_priv->saveDPLL_A_MD);
DRM_UDELAY(150);
I915_WRITE(VTOTAL_A, dev_priv->saveVTOTAL_A);
I915_WRITE(VBLANK_A, dev_priv->saveVBLANK_A);
I915_WRITE(VSYNC_A, dev_priv->saveVSYNC_A);
- I915_WRITE(BCLRPAT_A, dev_priv->saveBCLRPAT_A);
+ if (!IS_IGDNG(dev))
+ I915_WRITE(BCLRPAT_A, dev_priv->saveBCLRPAT_A);
+
+ if (IS_IGDNG(dev)) {
+ I915_WRITE(FDI_RXA_CTL, dev_priv->saveFDI_RXA_CTL);
+ I915_WRITE(FDI_TXA_CTL, dev_priv->saveFDI_TXA_CTL);
+
+ I915_WRITE(PFA_CTL_1, dev_priv->savePFA_CTL_1);
+ I915_WRITE(PFA_WIN_SZ, dev_priv->savePFA_WIN_SZ);
+ I915_WRITE(PFA_WIN_POS, dev_priv->savePFA_WIN_POS);
+
+ I915_WRITE(TRANS_HTOTAL_A, dev_priv->saveTRANS_HTOTAL_A);
+ I915_WRITE(TRANS_HBLANK_A, dev_priv->saveTRANS_HBLANK_A);
+ I915_WRITE(TRANS_HSYNC_A, dev_priv->saveTRANS_HSYNC_A);
+ I915_WRITE(TRANS_VTOTAL_A, dev_priv->saveTRANS_VTOTAL_A);
+ I915_WRITE(TRANS_VBLANK_A, dev_priv->saveTRANS_VBLANK_A);
+ I915_WRITE(TRANS_VSYNC_A, dev_priv->saveTRANS_VSYNC_A);
+ }
/* Restore plane info */
I915_WRITE(DSPASIZE, dev_priv->saveDSPASIZE);
/* Pipe & plane B info */
if (dev_priv->saveDPLL_B & DPLL_VCO_ENABLE) {
- I915_WRITE(DPLL_B, dev_priv->saveDPLL_B &
+ I915_WRITE(dpll_b_reg, dev_priv->saveDPLL_B &
~DPLL_VCO_ENABLE);
DRM_UDELAY(150);
}
- I915_WRITE(FPB0, dev_priv->saveFPB0);
- I915_WRITE(FPB1, dev_priv->saveFPB1);
+ I915_WRITE(fpb0_reg, dev_priv->saveFPB0);
+ I915_WRITE(fpb1_reg, dev_priv->saveFPB1);
/* Actually enable it */
- I915_WRITE(DPLL_B, dev_priv->saveDPLL_B);
+ I915_WRITE(dpll_b_reg, dev_priv->saveDPLL_B);
DRM_UDELAY(150);
if (IS_I965G(dev))
I915_WRITE(DPLL_B_MD, dev_priv->saveDPLL_B_MD);
I915_WRITE(VTOTAL_B, dev_priv->saveVTOTAL_B);
I915_WRITE(VBLANK_B, dev_priv->saveVBLANK_B);
I915_WRITE(VSYNC_B, dev_priv->saveVSYNC_B);
- I915_WRITE(BCLRPAT_B, dev_priv->saveBCLRPAT_B);
+ if (!IS_IGDNG(dev))
+ I915_WRITE(BCLRPAT_B, dev_priv->saveBCLRPAT_B);
+
+ if (IS_IGDNG(dev)) {
+ I915_WRITE(FDI_RXB_CTL, dev_priv->saveFDI_RXB_CTL);
+ I915_WRITE(FDI_TXB_CTL, dev_priv->saveFDI_TXB_CTL);
+
+ I915_WRITE(PFB_CTL_1, dev_priv->savePFB_CTL_1);
+ I915_WRITE(PFB_WIN_SZ, dev_priv->savePFB_WIN_SZ);
+ I915_WRITE(PFB_WIN_POS, dev_priv->savePFB_WIN_POS);
+
+ I915_WRITE(TRANS_HTOTAL_B, dev_priv->saveTRANS_HTOTAL_B);
+ I915_WRITE(TRANS_HBLANK_B, dev_priv->saveTRANS_HBLANK_B);
+ I915_WRITE(TRANS_HSYNC_B, dev_priv->saveTRANS_HSYNC_B);
+ I915_WRITE(TRANS_VTOTAL_B, dev_priv->saveTRANS_VTOTAL_B);
+ I915_WRITE(TRANS_VBLANK_B, dev_priv->saveTRANS_VBLANK_B);
+ I915_WRITE(TRANS_VSYNC_B, dev_priv->saveTRANS_VSYNC_B);
+ }
/* Restore plane info */
I915_WRITE(DSPBSIZE, dev_priv->saveDSPBSIZE);
dev_priv->saveCURSIZE = I915_READ(CURSIZE);
/* CRT state */
- dev_priv->saveADPA = I915_READ(ADPA);
+ if (IS_IGDNG(dev)) {
+ dev_priv->saveADPA = I915_READ(PCH_ADPA);
+ } else {
+ dev_priv->saveADPA = I915_READ(ADPA);
+ }
/* LVDS state */
- dev_priv->savePP_CONTROL = I915_READ(PP_CONTROL);
- dev_priv->savePFIT_PGM_RATIOS = I915_READ(PFIT_PGM_RATIOS);
- dev_priv->saveBLC_PWM_CTL = I915_READ(BLC_PWM_CTL);
- if (IS_I965G(dev))
- dev_priv->saveBLC_PWM_CTL2 = I915_READ(BLC_PWM_CTL2);
- if (IS_MOBILE(dev) && !IS_I830(dev))
- dev_priv->saveLVDS = I915_READ(LVDS);
- if (!IS_I830(dev) && !IS_845G(dev))
+ if (IS_IGDNG(dev)) {
+ dev_priv->savePP_CONTROL = I915_READ(PCH_PP_CONTROL);
+ dev_priv->saveBLC_PWM_CTL = I915_READ(BLC_PWM_PCH_CTL1);
+ dev_priv->saveBLC_PWM_CTL2 = I915_READ(BLC_PWM_PCH_CTL2);
+ dev_priv->saveBLC_CPU_PWM_CTL = I915_READ(BLC_PWM_CPU_CTL);
+ dev_priv->saveBLC_CPU_PWM_CTL2 = I915_READ(BLC_PWM_CPU_CTL2);
+ dev_priv->saveLVDS = I915_READ(PCH_LVDS);
+ } else {
+ dev_priv->savePP_CONTROL = I915_READ(PP_CONTROL);
+ dev_priv->savePFIT_PGM_RATIOS = I915_READ(PFIT_PGM_RATIOS);
+ dev_priv->saveBLC_PWM_CTL = I915_READ(BLC_PWM_CTL);
+ dev_priv->saveBLC_HIST_CTL = I915_READ(BLC_HIST_CTL);
+ if (IS_I965G(dev))
+ dev_priv->saveBLC_PWM_CTL2 = I915_READ(BLC_PWM_CTL2);
+ if (IS_MOBILE(dev) && !IS_I830(dev))
+ dev_priv->saveLVDS = I915_READ(LVDS);
+ }
+
+ if (!IS_I830(dev) && !IS_845G(dev) && !IS_IGDNG(dev))
dev_priv->savePFIT_CONTROL = I915_READ(PFIT_CONTROL);
- dev_priv->savePP_ON_DELAYS = I915_READ(PP_ON_DELAYS);
- dev_priv->savePP_OFF_DELAYS = I915_READ(PP_OFF_DELAYS);
- dev_priv->savePP_DIVISOR = I915_READ(PP_DIVISOR);
+
+ if (IS_IGDNG(dev)) {
+ dev_priv->savePP_ON_DELAYS = I915_READ(PCH_PP_ON_DELAYS);
+ dev_priv->savePP_OFF_DELAYS = I915_READ(PCH_PP_OFF_DELAYS);
+ dev_priv->savePP_DIVISOR = I915_READ(PCH_PP_DIVISOR);
+ } else {
+ dev_priv->savePP_ON_DELAYS = I915_READ(PP_ON_DELAYS);
+ dev_priv->savePP_OFF_DELAYS = I915_READ(PP_OFF_DELAYS);
+ dev_priv->savePP_DIVISOR = I915_READ(PP_DIVISOR);
+ }
/* Display Port state */
if (SUPPORTS_INTEGRATED_DP(dev)) {
/* FIXME: save TV & SDVO state */
/* FBC state */
- dev_priv->saveFBC_CFB_BASE = I915_READ(FBC_CFB_BASE);
- dev_priv->saveFBC_LL_BASE = I915_READ(FBC_LL_BASE);
- dev_priv->saveFBC_CONTROL2 = I915_READ(FBC_CONTROL2);
- dev_priv->saveFBC_CONTROL = I915_READ(FBC_CONTROL);
+ if (IS_GM45(dev)) {
+ dev_priv->saveDPFC_CB_BASE = I915_READ(DPFC_CB_BASE);
+ } else {
+ dev_priv->saveFBC_CFB_BASE = I915_READ(FBC_CFB_BASE);
+ dev_priv->saveFBC_LL_BASE = I915_READ(FBC_LL_BASE);
+ dev_priv->saveFBC_CONTROL2 = I915_READ(FBC_CONTROL2);
+ dev_priv->saveFBC_CONTROL = I915_READ(FBC_CONTROL);
+ }
/* VGA state */
dev_priv->saveVGA0 = I915_READ(VGA0);
dev_priv->saveVGA1 = I915_READ(VGA1);
dev_priv->saveVGA_PD = I915_READ(VGA_PD);
- dev_priv->saveVGACNTRL = I915_READ(VGACNTRL);
+ if (IS_IGDNG(dev))
+ dev_priv->saveVGACNTRL = I915_READ(CPU_VGACNTRL);
+ else
+ dev_priv->saveVGACNTRL = I915_READ(VGACNTRL);
i915_save_vga(dev);
}
I915_WRITE(CURSIZE, dev_priv->saveCURSIZE);
/* CRT state */
- I915_WRITE(ADPA, dev_priv->saveADPA);
+ if (IS_IGDNG(dev))
+ I915_WRITE(PCH_ADPA, dev_priv->saveADPA);
+ else
+ I915_WRITE(ADPA, dev_priv->saveADPA);
/* LVDS state */
- if (IS_I965G(dev))
+ if (IS_I965G(dev) && !IS_IGDNG(dev))
I915_WRITE(BLC_PWM_CTL2, dev_priv->saveBLC_PWM_CTL2);
- if (IS_MOBILE(dev) && !IS_I830(dev))
+
+ if (IS_IGDNG(dev)) {
+ I915_WRITE(PCH_LVDS, dev_priv->saveLVDS);
+ } else if (IS_MOBILE(dev) && !IS_I830(dev))
I915_WRITE(LVDS, dev_priv->saveLVDS);
- if (!IS_I830(dev) && !IS_845G(dev))
+
+ if (!IS_I830(dev) && !IS_845G(dev) && !IS_IGDNG(dev))
I915_WRITE(PFIT_CONTROL, dev_priv->savePFIT_CONTROL);
- I915_WRITE(PFIT_PGM_RATIOS, dev_priv->savePFIT_PGM_RATIOS);
- I915_WRITE(BLC_PWM_CTL, dev_priv->saveBLC_PWM_CTL);
- I915_WRITE(PP_ON_DELAYS, dev_priv->savePP_ON_DELAYS);
- I915_WRITE(PP_OFF_DELAYS, dev_priv->savePP_OFF_DELAYS);
- I915_WRITE(PP_DIVISOR, dev_priv->savePP_DIVISOR);
- I915_WRITE(PP_CONTROL, dev_priv->savePP_CONTROL);
+ if (IS_IGDNG(dev)) {
+ I915_WRITE(BLC_PWM_PCH_CTL1, dev_priv->saveBLC_PWM_CTL);
+ I915_WRITE(BLC_PWM_PCH_CTL2, dev_priv->saveBLC_PWM_CTL2);
+ I915_WRITE(BLC_PWM_CPU_CTL, dev_priv->saveBLC_CPU_PWM_CTL);
+ I915_WRITE(BLC_PWM_CPU_CTL2, dev_priv->saveBLC_CPU_PWM_CTL2);
+ I915_WRITE(PCH_PP_ON_DELAYS, dev_priv->savePP_ON_DELAYS);
+ I915_WRITE(PCH_PP_OFF_DELAYS, dev_priv->savePP_OFF_DELAYS);
+ I915_WRITE(PCH_PP_DIVISOR, dev_priv->savePP_DIVISOR);
+ I915_WRITE(PCH_PP_CONTROL, dev_priv->savePP_CONTROL);
+ } else {
+ I915_WRITE(PFIT_PGM_RATIOS, dev_priv->savePFIT_PGM_RATIOS);
+ I915_WRITE(BLC_PWM_CTL, dev_priv->saveBLC_PWM_CTL);
+ I915_WRITE(BLC_HIST_CTL, dev_priv->saveBLC_HIST_CTL);
+ I915_WRITE(PP_ON_DELAYS, dev_priv->savePP_ON_DELAYS);
+ I915_WRITE(PP_OFF_DELAYS, dev_priv->savePP_OFF_DELAYS);
+ I915_WRITE(PP_DIVISOR, dev_priv->savePP_DIVISOR);
+ I915_WRITE(PP_CONTROL, dev_priv->savePP_CONTROL);
+ }
/* Display Port state */
if (SUPPORTS_INTEGRATED_DP(dev)) {
/* FIXME: restore TV & SDVO state */
/* FBC info */
- I915_WRITE(FBC_CFB_BASE, dev_priv->saveFBC_CFB_BASE);
- I915_WRITE(FBC_LL_BASE, dev_priv->saveFBC_LL_BASE);
- I915_WRITE(FBC_CONTROL2, dev_priv->saveFBC_CONTROL2);
- I915_WRITE(FBC_CONTROL, dev_priv->saveFBC_CONTROL);
+ if (IS_GM45(dev)) {
+ g4x_disable_fbc(dev);
+ I915_WRITE(DPFC_CB_BASE, dev_priv->saveDPFC_CB_BASE);
+ } else {
+ i8xx_disable_fbc(dev);
+ I915_WRITE(FBC_CFB_BASE, dev_priv->saveFBC_CFB_BASE);
+ I915_WRITE(FBC_LL_BASE, dev_priv->saveFBC_LL_BASE);
+ I915_WRITE(FBC_CONTROL2, dev_priv->saveFBC_CONTROL2);
+ I915_WRITE(FBC_CONTROL, dev_priv->saveFBC_CONTROL);
+ }
/* VGA state */
- I915_WRITE(VGACNTRL, dev_priv->saveVGACNTRL);
+ if (IS_IGDNG(dev))
+ I915_WRITE(CPU_VGACNTRL, dev_priv->saveVGACNTRL);
+ else
+ I915_WRITE(VGACNTRL, dev_priv->saveVGACNTRL);
I915_WRITE(VGA0, dev_priv->saveVGA0);
I915_WRITE(VGA1, dev_priv->saveVGA1);
I915_WRITE(VGA_PD, dev_priv->saveVGA_PD);
i915_save_display(dev);
/* Interrupt state */
- dev_priv->saveIER = I915_READ(IER);
- dev_priv->saveIMR = I915_READ(IMR);
+ if (IS_IGDNG(dev)) {
+ dev_priv->saveDEIER = I915_READ(DEIER);
+ dev_priv->saveDEIMR = I915_READ(DEIMR);
+ dev_priv->saveGTIER = I915_READ(GTIER);
+ dev_priv->saveGTIMR = I915_READ(GTIMR);
+ dev_priv->saveFDI_RXA_IMR = I915_READ(FDI_RXA_IMR);
+ dev_priv->saveFDI_RXB_IMR = I915_READ(FDI_RXB_IMR);
+ } else {
+ dev_priv->saveIER = I915_READ(IER);
+ dev_priv->saveIMR = I915_READ(IMR);
+ }
/* Clock gating state */
dev_priv->saveD_STATE = I915_READ(D_STATE);
i915_restore_display(dev);
/* Interrupt state */
- I915_WRITE (IER, dev_priv->saveIER);
- I915_WRITE (IMR, dev_priv->saveIMR);
+ if (IS_IGDNG(dev)) {
+ I915_WRITE(DEIER, dev_priv->saveDEIER);
+ I915_WRITE(DEIMR, dev_priv->saveDEIMR);
+ I915_WRITE(GTIER, dev_priv->saveGTIER);
+ I915_WRITE(GTIMR, dev_priv->saveGTIMR);
+ I915_WRITE(FDI_RXA_IMR, dev_priv->saveFDI_RXA_IMR);
+ I915_WRITE(FDI_RXB_IMR, dev_priv->saveFDI_RXB_IMR);
+ } else {
+ I915_WRITE (IER, dev_priv->saveIER);
+ I915_WRITE (IMR, dev_priv->saveIMR);
+ }
/* Clock gating state */
I915_WRITE (D_STATE, dev_priv->saveD_STATE);
struct drm_device *dev = dev_priv->dev;
struct bdb_driver_features *driver;
- /* set default for chips without eDP */
- if (!SUPPORTS_EDP(dev)) {
- dev_priv->edp_support = 0;
- return;
- }
-
driver = find_section(bdb, BDB_DRIVER_FEATURES);
if (!driver)
return;
- if (driver->lvds_config == BDB_DRIVER_FEATURE_EDP)
+ if (driver && SUPPORTS_EDP(dev) &&
+ driver->lvds_config == BDB_DRIVER_FEATURE_EDP) {
dev_priv->edp_support = 1;
+ } else {
+ dev_priv->edp_support = 0;
+ }
- if (driver->dual_frequency)
+ if (driver && driver->dual_frequency)
dev_priv->render_reclock_avail = true;
}
clock.m = 5 * (clock.m1 + 2) + (clock.m2 + 2);
clock.p = (clock.p1 * clock.p2);
clock.dot = 96000 * clock.m / (clock.n + 2) / clock.p;
+ clock.vco = 0;
memcpy(best_clock, &clock, sizeof(intel_clock_t));
return true;
}
return ret;
}
- /* Pre-i965 needs to install a fence for tiled scan-out */
- if (!IS_I965G(dev) &&
- obj_priv->fence_reg == I915_FENCE_REG_NONE &&
+ /* Install a fence for tiled scan-out. Pre-i965 always needs a fence,
+ * whereas 965+ only requires a fence if using framebuffer compression.
+ * For simplicity, we always install a fence as the cost is not that onerous.
+ */
+ if (obj_priv->fence_reg == I915_FENCE_REG_NONE &&
obj_priv->tiling_mode != I915_TILING_NONE) {
ret = i915_gem_object_get_fence_reg(obj);
if (ret != 0) {
/* Enable panel fitting for LVDS */
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
temp = I915_READ(pf_ctl_reg);
- I915_WRITE(pf_ctl_reg, temp | PF_ENABLE);
+ I915_WRITE(pf_ctl_reg, temp | PF_ENABLE | PF_FILTER_MED_3x3);
/* currently full aspect */
I915_WRITE(pf_win_pos, 0);
case DRM_MODE_DPMS_ON:
case DRM_MODE_DPMS_STANDBY:
case DRM_MODE_DPMS_SUSPEND:
+ intel_update_watermarks(dev);
+
/* Enable the DPLL */
temp = I915_READ(dpll_reg);
if ((temp & DPLL_VCO_ENABLE) == 0) {
/* Give the overlay scaler a chance to enable if it's on this pipe */
//intel_crtc_dpms_video(crtc, true); TODO
- intel_update_watermarks(dev);
break;
case DRM_MODE_DPMS_OFF:
intel_update_watermarks(dev);
#define LINK_N 0x80000
static void
-igdng_compute_m_n(int bytes_per_pixel, int nlanes,
+igdng_compute_m_n(int bits_per_pixel, int nlanes,
int pixel_clock, int link_clock,
struct fdi_m_n *m_n)
{
temp = (u64) DATA_N * pixel_clock;
temp = div_u64(temp, link_clock);
- m_n->gmch_m = div_u64(temp * bytes_per_pixel, nlanes);
+ m_n->gmch_m = div_u64(temp * bits_per_pixel, nlanes);
+ m_n->gmch_m >>= 3; /* convert to bytes_per_pixel */
m_n->gmch_n = DATA_N;
fdi_reduce_ratio(&m_n->gmch_m, &m_n->gmch_n);
IGD_CURSOR_GUARD_WM,
IGD_FIFO_LINE_SIZE
};
+static struct intel_watermark_params g4x_wm_info = {
+ G4X_FIFO_SIZE,
+ G4X_MAX_WM,
+ G4X_MAX_WM,
+ 2,
+ G4X_FIFO_LINE_SIZE,
+};
static struct intel_watermark_params i945_wm_info = {
I945_FIFO_SIZE,
I915_MAX_WM,
return size;
}
-static void g4x_update_wm(struct drm_device *dev, int unused, int unused2,
- int unused3, int unused4)
+static void g4x_update_wm(struct drm_device *dev, int planea_clock,
+ int planeb_clock, int sr_hdisplay, int pixel_size)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- u32 fw_blc_self = I915_READ(FW_BLC_SELF);
+ int total_size, cacheline_size;
+ int planea_wm, planeb_wm, cursora_wm, cursorb_wm, cursor_sr;
+ struct intel_watermark_params planea_params, planeb_params;
+ unsigned long line_time_us;
+ int sr_clock, sr_entries = 0, entries_required;
- if (i915_powersave)
- fw_blc_self |= FW_BLC_SELF_EN;
- else
- fw_blc_self &= ~FW_BLC_SELF_EN;
- I915_WRITE(FW_BLC_SELF, fw_blc_self);
+ /* Create copies of the base settings for each pipe */
+ planea_params = planeb_params = g4x_wm_info;
+
+ /* Grab a couple of global values before we overwrite them */
+ total_size = planea_params.fifo_size;
+ cacheline_size = planea_params.cacheline_size;
+
+ /*
+ * Note: we need to make sure we don't overflow for various clock &
+ * latency values.
+ * clocks go from a few thousand to several hundred thousand.
+ * latency is usually a few thousand
+ */
+ entries_required = ((planea_clock / 1000) * pixel_size * latency_ns) /
+ 1000;
+ entries_required /= G4X_FIFO_LINE_SIZE;
+ planea_wm = entries_required + planea_params.guard_size;
+
+ entries_required = ((planeb_clock / 1000) * pixel_size * latency_ns) /
+ 1000;
+ entries_required /= G4X_FIFO_LINE_SIZE;
+ planeb_wm = entries_required + planeb_params.guard_size;
+
+ cursora_wm = cursorb_wm = 16;
+ cursor_sr = 32;
+
+ DRM_DEBUG("FIFO watermarks - A: %d, B: %d\n", planea_wm, planeb_wm);
+
+ /* Calc sr entries for one plane configs */
+ if (sr_hdisplay && (!planea_clock || !planeb_clock)) {
+ /* self-refresh has much higher latency */
+ const static int sr_latency_ns = 12000;
+
+ sr_clock = planea_clock ? planea_clock : planeb_clock;
+ line_time_us = ((sr_hdisplay * 1000) / sr_clock);
+
+ /* Use ns/us then divide to preserve precision */
+ sr_entries = (((sr_latency_ns / line_time_us) + 1) *
+ pixel_size * sr_hdisplay) / 1000;
+ sr_entries = roundup(sr_entries / cacheline_size, 1);
+ DRM_DEBUG("self-refresh entries: %d\n", sr_entries);
+ I915_WRITE(FW_BLC_SELF, FW_BLC_SELF_EN);
+ }
+
+ DRM_DEBUG("Setting FIFO watermarks - A: %d, B: %d, SR %d\n",
+ planea_wm, planeb_wm, sr_entries);
+
+ planea_wm &= 0x3f;
+ planeb_wm &= 0x3f;
+
+ I915_WRITE(DSPFW1, (sr_entries << DSPFW_SR_SHIFT) |
+ (cursorb_wm << DSPFW_CURSORB_SHIFT) |
+ (planeb_wm << DSPFW_PLANEB_SHIFT) | planea_wm);
+ I915_WRITE(DSPFW2, (I915_READ(DSPFW2) & DSPFW_CURSORA_MASK) |
+ (cursora_wm << DSPFW_CURSORA_SHIFT));
+ /* HPLL off in SR has some issues on G4x... disable it */
+ I915_WRITE(DSPFW3, (I915_READ(DSPFW3) & ~DSPFW_HPLL_SR_EN) |
+ (cursor_sr << DSPFW_CURSOR_SR_SHIFT));
}
static void i965_update_wm(struct drm_device *dev, int unused, int unused2,
unsigned long planea_clock = 0, planeb_clock = 0, sr_clock = 0;
int enabled = 0, pixel_size = 0;
+ if (!dev_priv->display.update_wm)
+ return;
+
/* Get the clock config from both planes */
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
intel_crtc = to_intel_crtc(crtc);
/* FDI link */
if (IS_IGDNG(dev)) {
- int lane, link_bw;
+ int lane, link_bw, bpp;
/* eDP doesn't require FDI link, so just set DP M/N
according to current link config */
if (is_edp) {
lane = 4;
link_bw = 270000;
}
- igdng_compute_m_n(3, lane, target_clock,
+
+ /* determine panel color depth */
+ temp = I915_READ(pipeconf_reg);
+
+ switch (temp & PIPE_BPC_MASK) {
+ case PIPE_8BPC:
+ bpp = 24;
+ break;
+ case PIPE_10BPC:
+ bpp = 30;
+ break;
+ case PIPE_6BPC:
+ bpp = 18;
+ break;
+ case PIPE_12BPC:
+ bpp = 36;
+ break;
+ default:
+ DRM_ERROR("unknown pipe bpc value\n");
+ bpp = 24;
+ }
+
+ igdng_compute_m_n(bpp, lane, target_clock,
link_bw, &m_n);
}
+ /* Ironlake: try to setup display ref clock before DPLL
+ * enabling. This is only under driver's control after
+ * PCH B stepping, previous chipset stepping should be
+ * ignoring this setting.
+ */
+ if (IS_IGDNG(dev)) {
+ temp = I915_READ(PCH_DREF_CONTROL);
+ /* Always enable nonspread source */
+ temp &= ~DREF_NONSPREAD_SOURCE_MASK;
+ temp |= DREF_NONSPREAD_SOURCE_ENABLE;
+ I915_WRITE(PCH_DREF_CONTROL, temp);
+ POSTING_READ(PCH_DREF_CONTROL);
+
+ temp &= ~DREF_SSC_SOURCE_MASK;
+ temp |= DREF_SSC_SOURCE_ENABLE;
+ I915_WRITE(PCH_DREF_CONTROL, temp);
+ POSTING_READ(PCH_DREF_CONTROL);
+
+ udelay(200);
+
+ if (is_edp) {
+ if (dev_priv->lvds_use_ssc) {
+ temp |= DREF_SSC1_ENABLE;
+ I915_WRITE(PCH_DREF_CONTROL, temp);
+ POSTING_READ(PCH_DREF_CONTROL);
+
+ udelay(200);
+
+ temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
+ temp |= DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD;
+ I915_WRITE(PCH_DREF_CONTROL, temp);
+ POSTING_READ(PCH_DREF_CONTROL);
+ } else {
+ temp |= DREF_CPU_SOURCE_OUTPUT_NONSPREAD;
+ I915_WRITE(PCH_DREF_CONTROL, temp);
+ POSTING_READ(PCH_DREF_CONTROL);
+ }
+ }
+ }
+
if (IS_IGD(dev)) {
fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2;
if (has_reduced_clock)
lvds = I915_READ(lvds_reg);
lvds |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP | LVDS_PIPEB_SELECT;
+ /* set the corresponsding LVDS_BORDER bit */
+ lvds |= dev_priv->lvds_border_bits;
/* Set the B0-B3 data pairs corresponding to whether we're going to
* set the DPLLs for dual-channel mode or not.
*/
* Disable clock gating reported to work incorrectly according to the
* specs, but enable as much else as we can.
*/
- if (IS_G4X(dev)) {
+ if (IS_IGDNG(dev)) {
+ return;
+ } else if (IS_G4X(dev)) {
uint32_t dspclk_gate;
I915_WRITE(RENCLK_GATE_D1, 0);
I915_WRITE(RENCLK_GATE_D2, VF_UNIT_CLOCK_GATE_DISABLE |
i830_get_display_clock_speed;
/* For FIFO watermark updates */
- if (IS_G4X(dev))
+ if (IS_IGDNG(dev))
+ dev_priv->display.update_wm = NULL;
+ else if (IS_G4X(dev))
dev_priv->display.update_wm = g4x_update_wm;
else if (IS_I965G(dev))
dev_priv->display.update_wm = i965_update_wm;
{
struct intel_dp_priv *dp_priv = intel_output->dev_priv;
- DRM_ERROR("i2c_init %s\n", name);
+ DRM_DEBUG_KMS("i2c_init %s\n", name);
dp_priv->algo.running = false;
dp_priv->algo.address = 0;
dp_priv->algo.aux_ch = intel_dp_i2c_aux_ch;
adjusted_mode->crtc_vblank_start + vsync_pos;
/* keep the vsync width constant */
adjusted_mode->crtc_vsync_end =
- adjusted_mode->crtc_vblank_start + vsync_width;
+ adjusted_mode->crtc_vsync_start + vsync_width;
border = 1;
break;
case DRM_MODE_SCALE_ASPECT:
lvds_priv->pfit_control = pfit_control;
lvds_priv->pfit_pgm_ratios = pfit_pgm_ratios;
/*
+ * When there exists the border, it means that the LVDS_BORDR
+ * should be enabled.
+ */
+ if (border)
+ dev_priv->lvds_border_bits |= LVDS_BORDER_ENABLE;
+ else
+ dev_priv->lvds_border_bits &= ~(LVDS_BORDER_ENABLE);
+ /*
* XXX: It would be nice to support lower refresh rates on the
* panels to reduce power consumption, and perhaps match the
* user's requested refresh rate.
/* The actual device the driver binds to */
static struct eeepc_hotk *ehotk;
-static void eeepc_rfkill_hotplug(bool real);
-
/* Platform device/driver */
static int eeepc_hotk_thaw(struct device *device);
static int eeepc_hotk_restore(struct device *device);
static int eeepc_rfkill_set(void *data, bool blocked)
{
unsigned long asl = (unsigned long)data;
- int ret;
-
- if (asl != CM_ASL_WLAN)
- return set_acpi(asl, !blocked);
-
- /* hack to avoid panic with rt2860sta */
- if (blocked)
- eeepc_rfkill_hotplug(false);
- ret = set_acpi(asl, !blocked);
- return ret;
+ return set_acpi(asl, !blocked);
}
static const struct rfkill_ops eeepc_rfkill_ops = {
* If the following call to set_acpi() fails, it's because there's no
* camera so we can ignore the error.
*/
- set_acpi(CM_ASL_CAMERA, 1);
+ if (get_acpi(CM_ASL_CAMERA) == 0)
+ set_acpi(CM_ASL_CAMERA, 1);
}
/*
return 0;
}
-static void eeepc_rfkill_hotplug(bool real)
+static void eeepc_rfkill_hotplug(void)
{
struct pci_dev *dev;
struct pci_bus *bus;
- bool blocked = real ? eeepc_wlan_rfkill_blocked() : true;
+ bool blocked = eeepc_wlan_rfkill_blocked();
- if (real && ehotk->wlan_rfkill)
+ if (ehotk->wlan_rfkill)
rfkill_set_sw_state(ehotk->wlan_rfkill, blocked);
mutex_lock(&ehotk->hotplug_lock);
if (event != ACPI_NOTIFY_BUS_CHECK)
return;
- eeepc_rfkill_hotplug(true);
+ eeepc_rfkill_hotplug();
}
static void eeepc_hotk_notify(struct acpi_device *device, u32 event)
{
/* Refresh both wlan rfkill state and pci hotplug */
if (ehotk->wlan_rfkill)
- eeepc_rfkill_hotplug(true);
+ eeepc_rfkill_hotplug();
if (ehotk->bluetooth_rfkill)
rfkill_set_sw_state(ehotk->bluetooth_rfkill,
* Refresh pci hotplug in case the rfkill state was changed after
* eeepc_unregister_rfkill_notifier()
*/
- eeepc_rfkill_hotplug(true);
+ eeepc_rfkill_hotplug();
if (ehotk->hotplug_slot)
pci_hp_deregister(ehotk->hotplug_slot);
* Refresh pci hotplug in case the rfkill state was changed during
* setup.
*/
- eeepc_rfkill_hotplug(true);
+ eeepc_rfkill_hotplug();
exit:
if (result && result != -ENODEV)
switch (type) {
case THERMAL_TRIP_CRITICAL:
- return sprintf(buf, "critical");
+ return sprintf(buf, "critical\n");
case THERMAL_TRIP_HOT:
- return sprintf(buf, "hot");
+ return sprintf(buf, "hot\n");
case THERMAL_TRIP_PASSIVE:
- return sprintf(buf, "passive");
+ return sprintf(buf, "passive\n");
case THERMAL_TRIP_ACTIVE:
- return sprintf(buf, "active");
+ return sprintf(buf, "active\n");
default:
- return sprintf(buf, "unknown");
+ return sprintf(buf, "unknown\n");
}
}
* @gfp_mask: allocation mask to use
* @nr_iovecs: number of iovecs
*
- * Allocate a new bio with @nr_iovecs bvecs. If @gfp_mask
- * contains __GFP_WAIT, the allocation is guaranteed to succeed.
+ * bio_alloc will allocate a bio and associated bio_vec array that can hold
+ * at least @nr_iovecs entries. Allocations will be done from the
+ * fs_bio_set. Also see @bio_alloc_bioset and @bio_kmalloc.
+ *
+ * If %__GFP_WAIT is set, then bio_alloc will always be able to allocate
+ * a bio. This is due to the mempool guarantees. To make this work, callers
+ * must never allocate more than 1 bio at a time from this pool. Callers
+ * that need to allocate more than 1 bio must always submit the previously
+ * allocated bio for IO before attempting to allocate a new one. Failure to
+ * do so can cause livelocks under memory pressure.
*
* RETURNS:
* Pointer to new bio on success, NULL on failure.
}
/**
- * bio_alloc - allocate a bio for I/O
+ * bio_kmalloc - allocate a bio for I/O using kmalloc()
* @gfp_mask: the GFP_ mask given to the slab allocator
* @nr_iovecs: number of iovecs to pre-allocate
*
* Description:
- * bio_alloc will allocate a bio and associated bio_vec array that can hold
- * at least @nr_iovecs entries. Allocations will be done from the
- * fs_bio_set. Also see @bio_alloc_bioset.
- *
- * If %__GFP_WAIT is set, then bio_alloc will always be able to allocate
- * a bio. This is due to the mempool guarantees. To make this work, callers
- * must never allocate more than 1 bio at a time from this pool. Callers
- * that need to allocate more than 1 bio must always submit the previously
- * allocated bio for IO before attempting to allocate a new one. Failure to
- * do so can cause livelocks under memory pressure.
+ * Allocate a new bio with @nr_iovecs bvecs. If @gfp_mask contains
+ * %__GFP_WAIT, the allocation is guaranteed to succeed.
*
**/
struct bio *bio_kmalloc(gfp_t gfp_mask, int nr_iovecs)
*
* Description:
* Put a reference to a &struct bio, either one you have gotten with
- * bio_alloc or bio_get. The last put of a bio will free it.
+ * bio_alloc, bio_get or bio_clone. The last put of a bio will free it.
**/
void bio_put(struct bio *bio)
{
void bdi_unregister(struct backing_dev_info *bdi)
{
if (bdi->dev) {
+ bdi_prune_sb(bdi);
+
if (!bdi_cap_flush_forker(bdi))
bdi_wb_shutdown(bdi);
bdi_debug_unregister(bdi);
spin_unlock(&inode_lock);
}
- bdi_prune_sb(bdi);
bdi_unregister(bdi);
for (i = 0; i < NR_BDI_STAT_ITEMS; i++)
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff