ide: call ide_build_sglist() prior to ->dma_setup (v2)
[safe/jmp/linux-2.6] / include / linux / ide.h
1 #ifndef _IDE_H
2 #define _IDE_H
3 /*
4  *  linux/include/linux/ide.h
5  *
6  *  Copyright (C) 1994-2002  Linus Torvalds & authors
7  */
8
9 #include <linux/init.h>
10 #include <linux/ioport.h>
11 #include <linux/ata.h>
12 #include <linux/blkdev.h>
13 #include <linux/proc_fs.h>
14 #include <linux/interrupt.h>
15 #include <linux/bitops.h>
16 #include <linux/bio.h>
17 #include <linux/device.h>
18 #include <linux/pci.h>
19 #include <linux/completion.h>
20 #include <linux/pm.h>
21 #ifdef CONFIG_BLK_DEV_IDEACPI
22 #include <acpi/acpi.h>
23 #endif
24 #include <asm/byteorder.h>
25 #include <asm/system.h>
26 #include <asm/io.h>
27 #include <asm/mutex.h>
28
29 #if defined(CONFIG_CRIS) || defined(CONFIG_FRV) || defined(CONFIG_MN10300)
30 # define SUPPORT_VLB_SYNC 0
31 #else
32 # define SUPPORT_VLB_SYNC 1
33 #endif
34
35 /*
36  * Probably not wise to fiddle with these
37  */
38 #define IDE_DEFAULT_MAX_FAILURES        1
39 #define ERROR_MAX       8       /* Max read/write errors per sector */
40 #define ERROR_RESET     3       /* Reset controller every 4th retry */
41 #define ERROR_RECAL     1       /* Recalibrate every 2nd retry */
42
43 /* Error codes returned in rq->errors to the higher part of the driver. */
44 enum {
45         IDE_DRV_ERROR_GENERAL   = 101,
46         IDE_DRV_ERROR_FILEMARK  = 102,
47         IDE_DRV_ERROR_EOD       = 103,
48 };
49
50 /*
51  * Definitions for accessing IDE controller registers
52  */
53 #define IDE_NR_PORTS            (10)
54
55 struct ide_io_ports {
56         unsigned long   data_addr;
57
58         union {
59                 unsigned long error_addr;       /*   read:  error */
60                 unsigned long feature_addr;     /*  write: feature */
61         };
62
63         unsigned long   nsect_addr;
64         unsigned long   lbal_addr;
65         unsigned long   lbam_addr;
66         unsigned long   lbah_addr;
67
68         unsigned long   device_addr;
69
70         union {
71                 unsigned long status_addr;      /*  read: status  */
72                 unsigned long command_addr;     /* write: command */
73         };
74
75         unsigned long   ctl_addr;
76
77         unsigned long   irq_addr;
78 };
79
80 #define OK_STAT(stat,good,bad)  (((stat)&((good)|(bad)))==(good))
81
82 #define BAD_R_STAT      (ATA_BUSY | ATA_ERR)
83 #define BAD_W_STAT      (BAD_R_STAT | ATA_DF)
84 #define BAD_STAT        (BAD_R_STAT | ATA_DRQ)
85 #define DRIVE_READY     (ATA_DRDY | ATA_DSC)
86
87 #define BAD_CRC         (ATA_ABORTED | ATA_ICRC)
88
89 #define SATA_NR_PORTS           (3)     /* 16 possible ?? */
90
91 #define SATA_STATUS_OFFSET      (0)
92 #define SATA_ERROR_OFFSET       (1)
93 #define SATA_CONTROL_OFFSET     (2)
94
95 /*
96  * Our Physical Region Descriptor (PRD) table should be large enough
97  * to handle the biggest I/O request we are likely to see.  Since requests
98  * can have no more than 256 sectors, and since the typical blocksize is
99  * two or more sectors, we could get by with a limit of 128 entries here for
100  * the usual worst case.  Most requests seem to include some contiguous blocks,
101  * further reducing the number of table entries required.
102  *
103  * The driver reverts to PIO mode for individual requests that exceed
104  * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
105  * 100% of all crazy scenarios here is not necessary.
106  *
107  * As it turns out though, we must allocate a full 4KB page for this,
108  * so the two PRD tables (ide0 & ide1) will each get half of that,
109  * allowing each to have about 256 entries (8 bytes each) from this.
110  */
111 #define PRD_BYTES       8
112 #define PRD_ENTRIES     256
113
114 /*
115  * Some more useful definitions
116  */
117 #define PARTN_BITS      6       /* number of minor dev bits for partitions */
118 #define MAX_DRIVES      2       /* per interface; 2 assumed by lots of code */
119 #define SECTOR_SIZE     512
120
121 /*
122  * Timeouts for various operations:
123  */
124 enum {
125         /* spec allows up to 20ms */
126         WAIT_DRQ        = HZ / 10,      /* 100ms */
127         /* some laptops are very slow */
128         WAIT_READY      = 5 * HZ,       /* 5s */
129         /* should be less than 3ms (?), if all ATAPI CD is closed at boot */
130         WAIT_PIDENTIFY  = 10 * HZ,      /* 10s */
131         /* worst case when spinning up */
132         WAIT_WORSTCASE  = 30 * HZ,      /* 30s */
133         /* maximum wait for an IRQ to happen */
134         WAIT_CMD        = 10 * HZ,      /* 10s */
135         /* Some drives require a longer IRQ timeout. */
136         WAIT_FLOPPY_CMD = 50 * HZ,      /* 50s */
137         /*
138          * Some drives (for example, Seagate STT3401A Travan) require a very
139          * long timeout, because they don't return an interrupt or clear their
140          * BSY bit until after the command completes (even retension commands).
141          */
142         WAIT_TAPE_CMD   = 900 * HZ,     /* 900s */
143         /* minimum sleep time */
144         WAIT_MIN_SLEEP  = HZ / 50,      /* 20ms */
145 };
146
147 /*
148  * Op codes for special requests to be handled by ide_special_rq().
149  * Values should be in the range of 0x20 to 0x3f.
150  */
151 #define REQ_DRIVE_RESET         0x20
152 #define REQ_DEVSET_EXEC         0x21
153 #define REQ_PARK_HEADS          0x22
154 #define REQ_UNPARK_HEADS        0x23
155
156 /*
157  * Check for an interrupt and acknowledge the interrupt status
158  */
159 struct hwif_s;
160 typedef int (ide_ack_intr_t)(struct hwif_s *);
161
162 /*
163  * hwif_chipset_t is used to keep track of the specific hardware
164  * chipset used by each IDE interface, if known.
165  */
166 enum {          ide_unknown,    ide_generic,    ide_pci,
167                 ide_cmd640,     ide_dtc2278,    ide_ali14xx,
168                 ide_qd65xx,     ide_umc8672,    ide_ht6560b,
169                 ide_4drives,    ide_pmac,       ide_acorn,
170                 ide_au1xxx,     ide_palm3710
171 };
172
173 typedef u8 hwif_chipset_t;
174
175 /*
176  * Structure to hold all information about the location of this port
177  */
178 typedef struct hw_regs_s {
179         union {
180                 struct ide_io_ports     io_ports;
181                 unsigned long           io_ports_array[IDE_NR_PORTS];
182         };
183
184         int             irq;                    /* our irq number */
185         ide_ack_intr_t  *ack_intr;              /* acknowledge interrupt */
186         hwif_chipset_t  chipset;
187         struct device   *dev, *parent;
188         unsigned long   config;
189 } hw_regs_t;
190
191 static inline void ide_std_init_ports(hw_regs_t *hw,
192                                       unsigned long io_addr,
193                                       unsigned long ctl_addr)
194 {
195         unsigned int i;
196
197         for (i = 0; i <= 7; i++)
198                 hw->io_ports_array[i] = io_addr++;
199
200         hw->io_ports.ctl_addr = ctl_addr;
201 }
202
203 #define MAX_HWIFS       10
204
205 /*
206  * Now for the data we need to maintain per-drive:  ide_drive_t
207  */
208
209 #define ide_scsi        0x21
210 #define ide_disk        0x20
211 #define ide_optical     0x7
212 #define ide_cdrom       0x5
213 #define ide_tape        0x1
214 #define ide_floppy      0x0
215
216 /*
217  * Special Driver Flags
218  *
219  * set_geometry : respecify drive geometry
220  * recalibrate  : seek to cyl 0
221  * set_multmode : set multmode count
222  * reserved     : unused
223  */
224 typedef union {
225         unsigned all                    : 8;
226         struct {
227                 unsigned set_geometry   : 1;
228                 unsigned recalibrate    : 1;
229                 unsigned set_multmode   : 1;
230                 unsigned reserved       : 5;
231         } b;
232 } special_t;
233
234 /*
235  * Status returned from various ide_ functions
236  */
237 typedef enum {
238         ide_stopped,    /* no drive operation was started */
239         ide_started,    /* a drive operation was started, handler was set */
240 } ide_startstop_t;
241
242 enum {
243         IDE_TFLAG_LBA48                 = (1 << 0),
244         IDE_TFLAG_OUT_HOB_FEATURE       = (1 << 1),
245         IDE_TFLAG_OUT_HOB_NSECT         = (1 << 2),
246         IDE_TFLAG_OUT_HOB_LBAL          = (1 << 3),
247         IDE_TFLAG_OUT_HOB_LBAM          = (1 << 4),
248         IDE_TFLAG_OUT_HOB_LBAH          = (1 << 5),
249         IDE_TFLAG_OUT_HOB               = IDE_TFLAG_OUT_HOB_FEATURE |
250                                           IDE_TFLAG_OUT_HOB_NSECT |
251                                           IDE_TFLAG_OUT_HOB_LBAL |
252                                           IDE_TFLAG_OUT_HOB_LBAM |
253                                           IDE_TFLAG_OUT_HOB_LBAH,
254         IDE_TFLAG_OUT_FEATURE           = (1 << 6),
255         IDE_TFLAG_OUT_NSECT             = (1 << 7),
256         IDE_TFLAG_OUT_LBAL              = (1 << 8),
257         IDE_TFLAG_OUT_LBAM              = (1 << 9),
258         IDE_TFLAG_OUT_LBAH              = (1 << 10),
259         IDE_TFLAG_OUT_TF                = IDE_TFLAG_OUT_FEATURE |
260                                           IDE_TFLAG_OUT_NSECT |
261                                           IDE_TFLAG_OUT_LBAL |
262                                           IDE_TFLAG_OUT_LBAM |
263                                           IDE_TFLAG_OUT_LBAH,
264         IDE_TFLAG_OUT_DEVICE            = (1 << 11),
265         IDE_TFLAG_WRITE                 = (1 << 12),
266         IDE_TFLAG_CUSTOM_HANDLER        = (1 << 13),
267         IDE_TFLAG_DMA_PIO_FALLBACK      = (1 << 14),
268         IDE_TFLAG_IN_HOB_FEATURE        = (1 << 15),
269         IDE_TFLAG_IN_HOB_NSECT          = (1 << 16),
270         IDE_TFLAG_IN_HOB_LBAL           = (1 << 17),
271         IDE_TFLAG_IN_HOB_LBAM           = (1 << 18),
272         IDE_TFLAG_IN_HOB_LBAH           = (1 << 19),
273         IDE_TFLAG_IN_HOB_LBA            = IDE_TFLAG_IN_HOB_LBAL |
274                                           IDE_TFLAG_IN_HOB_LBAM |
275                                           IDE_TFLAG_IN_HOB_LBAH,
276         IDE_TFLAG_IN_HOB                = IDE_TFLAG_IN_HOB_FEATURE |
277                                           IDE_TFLAG_IN_HOB_NSECT |
278                                           IDE_TFLAG_IN_HOB_LBA,
279         IDE_TFLAG_IN_FEATURE            = (1 << 20),
280         IDE_TFLAG_IN_NSECT              = (1 << 21),
281         IDE_TFLAG_IN_LBAL               = (1 << 22),
282         IDE_TFLAG_IN_LBAM               = (1 << 23),
283         IDE_TFLAG_IN_LBAH               = (1 << 24),
284         IDE_TFLAG_IN_LBA                = IDE_TFLAG_IN_LBAL |
285                                           IDE_TFLAG_IN_LBAM |
286                                           IDE_TFLAG_IN_LBAH,
287         IDE_TFLAG_IN_TF                 = IDE_TFLAG_IN_NSECT |
288                                           IDE_TFLAG_IN_LBA,
289         IDE_TFLAG_IN_DEVICE             = (1 << 25),
290         IDE_TFLAG_HOB                   = IDE_TFLAG_OUT_HOB |
291                                           IDE_TFLAG_IN_HOB,
292         IDE_TFLAG_TF                    = IDE_TFLAG_OUT_TF |
293                                           IDE_TFLAG_IN_TF,
294         IDE_TFLAG_DEVICE                = IDE_TFLAG_OUT_DEVICE |
295                                           IDE_TFLAG_IN_DEVICE,
296         /* force 16-bit I/O operations */
297         IDE_TFLAG_IO_16BIT              = (1 << 26),
298         /* ide_task_t was allocated using kmalloc() */
299         IDE_TFLAG_DYN                   = (1 << 27),
300 };
301
302 enum {
303         IDE_FTFLAG_FLAGGED              = (1 << 0),
304         IDE_FTFLAG_SET_IN_FLAGS         = (1 << 1),
305         IDE_FTFLAG_OUT_DATA             = (1 << 2),
306         IDE_FTFLAG_IN_DATA              = (1 << 3),
307 };
308
309 struct ide_taskfile {
310         u8      hob_data;       /*  0: high data byte (for TASKFILE IOCTL) */
311
312         u8      hob_feature;    /*  1-5: additional data to support LBA48 */
313         u8      hob_nsect;
314         u8      hob_lbal;
315         u8      hob_lbam;
316         u8      hob_lbah;
317
318         u8      data;           /*  6: low data byte (for TASKFILE IOCTL) */
319
320         union {                 /*  7: */
321                 u8 error;       /*   read:  error */
322                 u8 feature;     /*  write: feature */
323         };
324
325         u8      nsect;          /*  8: number of sectors */
326         u8      lbal;           /*  9: LBA low */
327         u8      lbam;           /* 10: LBA mid */
328         u8      lbah;           /* 11: LBA high */
329
330         u8      device;         /* 12: device select */
331
332         union {                 /* 13: */
333                 u8 status;      /*  read: status  */
334                 u8 command;     /* write: command */
335         };
336 };
337
338 typedef struct ide_task_s {
339         union {
340                 struct ide_taskfile     tf;
341                 u8                      tf_array[14];
342         };
343         u8                      ftf_flags;      /* for TASKFILE ioctl */
344         u32                     tf_flags;
345         int                     data_phase;
346         struct request          *rq;            /* copy of request */
347         void                    *special;       /* valid_t generally */
348 } ide_task_t;
349
350 /* ATAPI packet command flags */
351 enum {
352         /* set when an error is considered normal - no retry (ide-tape) */
353         PC_FLAG_ABORT                   = (1 << 0),
354         PC_FLAG_SUPPRESS_ERROR          = (1 << 1),
355         PC_FLAG_WAIT_FOR_DSC            = (1 << 2),
356         PC_FLAG_DMA_OK                  = (1 << 3),
357         PC_FLAG_DMA_IN_PROGRESS         = (1 << 4),
358         PC_FLAG_DMA_ERROR               = (1 << 5),
359         PC_FLAG_WRITING                 = (1 << 6),
360 };
361
362 /*
363  * With each packet command, we allocate a buffer of IDE_PC_BUFFER_SIZE bytes.
364  * This is used for several packet commands (not for READ/WRITE commands).
365  */
366 #define IDE_PC_BUFFER_SIZE      256
367 #define ATAPI_WAIT_PC           (60 * HZ)
368
369 struct ide_atapi_pc {
370         /* actual packet bytes */
371         u8 c[12];
372         /* incremented on each retry */
373         int retries;
374         int error;
375
376         /* bytes to transfer */
377         int req_xfer;
378         /* bytes actually transferred */
379         int xferred;
380
381         /* data buffer */
382         u8 *buf;
383         /* current buffer position */
384         u8 *cur_pos;
385         int buf_size;
386         /* missing/available data on the current buffer */
387         int b_count;
388
389         /* the corresponding request */
390         struct request *rq;
391
392         unsigned long flags;
393
394         /*
395          * those are more or less driver-specific and some of them are subject
396          * to change/removal later.
397          */
398         u8 pc_buf[IDE_PC_BUFFER_SIZE];
399
400         /* idetape only */
401         struct idetape_bh *bh;
402         char *b_data;
403
404         struct scatterlist *sg;
405         unsigned int sg_cnt;
406
407         unsigned long timeout;
408 };
409
410 struct ide_devset;
411 struct ide_driver;
412
413 #ifdef CONFIG_BLK_DEV_IDEACPI
414 struct ide_acpi_drive_link;
415 struct ide_acpi_hwif_link;
416 #endif
417
418 struct ide_drive_s;
419
420 struct ide_disk_ops {
421         int             (*check)(struct ide_drive_s *, const char *);
422         int             (*get_capacity)(struct ide_drive_s *);
423         void            (*setup)(struct ide_drive_s *);
424         void            (*flush)(struct ide_drive_s *);
425         int             (*init_media)(struct ide_drive_s *, struct gendisk *);
426         int             (*set_doorlock)(struct ide_drive_s *, struct gendisk *,
427                                         int);
428         ide_startstop_t (*do_request)(struct ide_drive_s *, struct request *,
429                                       sector_t);
430         int             (*ioctl)(struct ide_drive_s *, struct block_device *,
431                                  fmode_t, unsigned int, unsigned long);
432 };
433
434 /* ATAPI device flags */
435 enum {
436         IDE_AFLAG_DRQ_INTERRUPT         = (1 << 0),
437
438         /* ide-cd */
439         /* Drive cannot eject the disc. */
440         IDE_AFLAG_NO_EJECT              = (1 << 1),
441         /* Drive is a pre ATAPI 1.2 drive. */
442         IDE_AFLAG_PRE_ATAPI12           = (1 << 2),
443         /* TOC addresses are in BCD. */
444         IDE_AFLAG_TOCADDR_AS_BCD        = (1 << 3),
445         /* TOC track numbers are in BCD. */
446         IDE_AFLAG_TOCTRACKS_AS_BCD      = (1 << 4),
447         /*
448          * Drive does not provide data in multiples of SECTOR_SIZE
449          * when more than one interrupt is needed.
450          */
451         IDE_AFLAG_LIMIT_NFRAMES         = (1 << 5),
452         /* Saved TOC information is current. */
453         IDE_AFLAG_TOC_VALID             = (1 << 6),
454         /* We think that the drive door is locked. */
455         IDE_AFLAG_DOOR_LOCKED           = (1 << 7),
456         /* SET_CD_SPEED command is unsupported. */
457         IDE_AFLAG_NO_SPEED_SELECT       = (1 << 8),
458         IDE_AFLAG_VERTOS_300_SSD        = (1 << 9),
459         IDE_AFLAG_VERTOS_600_ESD        = (1 << 10),
460         IDE_AFLAG_SANYO_3CD             = (1 << 11),
461         IDE_AFLAG_FULL_CAPS_PAGE        = (1 << 12),
462         IDE_AFLAG_PLAY_AUDIO_OK         = (1 << 13),
463         IDE_AFLAG_LE_SPEED_FIELDS       = (1 << 14),
464
465         /* ide-floppy */
466         /* Avoid commands not supported in Clik drive */
467         IDE_AFLAG_CLIK_DRIVE            = (1 << 15),
468         /* Requires BH algorithm for packets */
469         IDE_AFLAG_ZIP_DRIVE             = (1 << 16),
470         /* Supports format progress report */
471         IDE_AFLAG_SRFP                  = (1 << 17),
472
473         /* ide-tape */
474         IDE_AFLAG_IGNORE_DSC            = (1 << 18),
475         /* 0 When the tape position is unknown */
476         IDE_AFLAG_ADDRESS_VALID         = (1 << 19),
477         /* Device already opened */
478         IDE_AFLAG_BUSY                  = (1 << 20),
479         /* Attempt to auto-detect the current user block size */
480         IDE_AFLAG_DETECT_BS             = (1 << 21),
481         /* Currently on a filemark */
482         IDE_AFLAG_FILEMARK              = (1 << 22),
483         /* 0 = no tape is loaded, so we don't rewind after ejecting */
484         IDE_AFLAG_MEDIUM_PRESENT        = (1 << 23),
485
486         IDE_AFLAG_NO_AUTOCLOSE          = (1 << 24),
487 };
488
489 /* device flags */
490 enum {
491         /* restore settings after device reset */
492         IDE_DFLAG_KEEP_SETTINGS         = (1 << 0),
493         /* device is using DMA for read/write */
494         IDE_DFLAG_USING_DMA             = (1 << 1),
495         /* okay to unmask other IRQs */
496         IDE_DFLAG_UNMASK                = (1 << 2),
497         /* don't attempt flushes */
498         IDE_DFLAG_NOFLUSH               = (1 << 3),
499         /* DSC overlap */
500         IDE_DFLAG_DSC_OVERLAP           = (1 << 4),
501         /* give potential excess bandwidth */
502         IDE_DFLAG_NICE1                 = (1 << 5),
503         /* device is physically present */
504         IDE_DFLAG_PRESENT               = (1 << 6),
505         /* id read from device (synthetic if not set) */
506         IDE_DFLAG_ID_READ               = (1 << 8),
507         IDE_DFLAG_NOPROBE               = (1 << 9),
508         /* need to do check_media_change() */
509         IDE_DFLAG_REMOVABLE             = (1 << 10),
510         /* needed for removable devices */
511         IDE_DFLAG_ATTACH                = (1 << 11),
512         IDE_DFLAG_FORCED_GEOM           = (1 << 12),
513         /* disallow setting unmask bit */
514         IDE_DFLAG_NO_UNMASK             = (1 << 13),
515         /* disallow enabling 32-bit I/O */
516         IDE_DFLAG_NO_IO_32BIT           = (1 << 14),
517         /* for removable only: door lock/unlock works */
518         IDE_DFLAG_DOORLOCKING           = (1 << 15),
519         /* disallow DMA */
520         IDE_DFLAG_NODMA                 = (1 << 16),
521         /* powermanagment told us not to do anything, so sleep nicely */
522         IDE_DFLAG_BLOCKED               = (1 << 17),
523         /* sleeping & sleep field valid */
524         IDE_DFLAG_SLEEPING              = (1 << 18),
525         IDE_DFLAG_POST_RESET            = (1 << 19),
526         IDE_DFLAG_UDMA33_WARNED         = (1 << 20),
527         IDE_DFLAG_LBA48                 = (1 << 21),
528         /* status of write cache */
529         IDE_DFLAG_WCACHE                = (1 << 22),
530         /* used for ignoring ATA_DF */
531         IDE_DFLAG_NOWERR                = (1 << 23),
532         /* retrying in PIO */
533         IDE_DFLAG_DMA_PIO_RETRY         = (1 << 24),
534         IDE_DFLAG_LBA                   = (1 << 25),
535         /* don't unload heads */
536         IDE_DFLAG_NO_UNLOAD             = (1 << 26),
537         /* heads unloaded, please don't reset port */
538         IDE_DFLAG_PARKED                = (1 << 27),
539         IDE_DFLAG_MEDIA_CHANGED         = (1 << 28),
540         /* write protect */
541         IDE_DFLAG_WP                    = (1 << 29),
542         IDE_DFLAG_FORMAT_IN_PROGRESS    = (1 << 30),
543 };
544
545 struct ide_drive_s {
546         char            name[4];        /* drive name, such as "hda" */
547         char            driver_req[10]; /* requests specific driver */
548
549         struct request_queue    *queue; /* request queue */
550
551         struct request          *rq;    /* current request */
552         void            *driver_data;   /* extra driver data */
553         u16                     *id;    /* identification info */
554 #ifdef CONFIG_IDE_PROC_FS
555         struct proc_dir_entry *proc;    /* /proc/ide/ directory entry */
556         const struct ide_proc_devset *settings; /* /proc/ide/ drive settings */
557 #endif
558         struct hwif_s           *hwif;  /* actually (ide_hwif_t *) */
559
560         const struct ide_disk_ops *disk_ops;
561
562         unsigned long dev_flags;
563
564         unsigned long sleep;            /* sleep until this time */
565         unsigned long timeout;          /* max time to wait for irq */
566
567         special_t       special;        /* special action flags */
568
569         u8      select;                 /* basic drive/head select reg value */
570         u8      retry_pio;              /* retrying dma capable host in pio */
571         u8      waiting_for_dma;        /* dma currently in progress */
572         u8      dma;                    /* atapi dma flag */
573
574         u8      quirk_list;     /* considered quirky, set for a specific host */
575         u8      init_speed;     /* transfer rate set at boot */
576         u8      current_speed;  /* current transfer rate set */
577         u8      desired_speed;  /* desired transfer rate set */
578         u8      dn;             /* now wide spread use */
579         u8      acoustic;       /* acoustic management */
580         u8      media;          /* disk, cdrom, tape, floppy, ... */
581         u8      ready_stat;     /* min status value for drive ready */
582         u8      mult_count;     /* current multiple sector setting */
583         u8      mult_req;       /* requested multiple sector setting */
584         u8      io_32bit;       /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
585         u8      bad_wstat;      /* used for ignoring ATA_DF */
586         u8      head;           /* "real" number of heads */
587         u8      sect;           /* "real" sectors per track */
588         u8      bios_head;      /* BIOS/fdisk/LILO number of heads */
589         u8      bios_sect;      /* BIOS/fdisk/LILO sectors per track */
590
591         /* delay this long before sending packet command */
592         u8 pc_delay;
593
594         unsigned int    bios_cyl;       /* BIOS/fdisk/LILO number of cyls */
595         unsigned int    cyl;            /* "real" number of cyls */
596         unsigned int    drive_data;     /* used by set_pio_mode/selectproc */
597         unsigned int    failures;       /* current failure count */
598         unsigned int    max_failures;   /* maximum allowed failure count */
599         u64             probed_capacity;/* initial reported media capacity (ide-cd only currently) */
600
601         u64             capacity64;     /* total number of sectors */
602
603         int             lun;            /* logical unit */
604         int             crc_count;      /* crc counter to reduce drive speed */
605
606         unsigned long   debug_mask;     /* debugging levels switch */
607
608 #ifdef CONFIG_BLK_DEV_IDEACPI
609         struct ide_acpi_drive_link *acpidata;
610 #endif
611         struct list_head list;
612         struct device   gendev;
613         struct completion gendev_rel_comp;      /* to deal with device release() */
614
615         /* current packet command */
616         struct ide_atapi_pc *pc;
617
618         /* last failed packet command */
619         struct ide_atapi_pc *failed_pc;
620
621         /* callback for packet commands */
622         int  (*pc_callback)(struct ide_drive_s *, int);
623
624         void (*pc_update_buffers)(struct ide_drive_s *, struct ide_atapi_pc *);
625         int  (*pc_io_buffers)(struct ide_drive_s *, struct ide_atapi_pc *,
626                               unsigned int, int);
627
628         ide_startstop_t (*irq_handler)(struct ide_drive_s *);
629
630         unsigned long atapi_flags;
631
632         struct ide_atapi_pc request_sense_pc;
633         struct request request_sense_rq;
634 };
635
636 typedef struct ide_drive_s ide_drive_t;
637
638 #define to_ide_device(dev)              container_of(dev, ide_drive_t, gendev)
639
640 #define to_ide_drv(obj, cont_type)      \
641         container_of(obj, struct cont_type, dev)
642
643 #define ide_drv_g(disk, cont_type)      \
644         container_of((disk)->private_data, struct cont_type, driver)
645
646 struct ide_port_info;
647
648 struct ide_tp_ops {
649         void    (*exec_command)(struct hwif_s *, u8);
650         u8      (*read_status)(struct hwif_s *);
651         u8      (*read_altstatus)(struct hwif_s *);
652
653         void    (*set_irq)(struct hwif_s *, int);
654
655         void    (*tf_load)(ide_drive_t *, struct ide_task_s *);
656         void    (*tf_read)(ide_drive_t *, struct ide_task_s *);
657
658         void    (*input_data)(ide_drive_t *, struct request *, void *,
659                               unsigned int);
660         void    (*output_data)(ide_drive_t *, struct request *, void *,
661                                unsigned int);
662 };
663
664 extern const struct ide_tp_ops default_tp_ops;
665
666 /**
667  * struct ide_port_ops - IDE port operations
668  *
669  * @init_dev:           host specific initialization of a device
670  * @set_pio_mode:       routine to program host for PIO mode
671  * @set_dma_mode:       routine to program host for DMA mode
672  * @selectproc:         tweaks hardware to select drive
673  * @reset_poll:         chipset polling based on hba specifics
674  * @pre_reset:          chipset specific changes to default for device-hba resets
675  * @resetproc:          routine to reset controller after a disk reset
676  * @maskproc:           special host masking for drive selection
677  * @quirkproc:          check host's drive quirk list
678  * @clear_irq:          clear IRQ
679  *
680  * @mdma_filter:        filter MDMA modes
681  * @udma_filter:        filter UDMA modes
682  *
683  * @cable_detect:       detect cable type
684  */
685 struct ide_port_ops {
686         void    (*init_dev)(ide_drive_t *);
687         void    (*set_pio_mode)(ide_drive_t *, const u8);
688         void    (*set_dma_mode)(ide_drive_t *, const u8);
689         void    (*selectproc)(ide_drive_t *);
690         int     (*reset_poll)(ide_drive_t *);
691         void    (*pre_reset)(ide_drive_t *);
692         void    (*resetproc)(ide_drive_t *);
693         void    (*maskproc)(ide_drive_t *, int);
694         void    (*quirkproc)(ide_drive_t *);
695         void    (*clear_irq)(ide_drive_t *);
696
697         u8      (*mdma_filter)(ide_drive_t *);
698         u8      (*udma_filter)(ide_drive_t *);
699
700         u8      (*cable_detect)(struct hwif_s *);
701 };
702
703 struct ide_dma_ops {
704         void    (*dma_host_set)(struct ide_drive_s *, int);
705         int     (*dma_setup)(struct ide_drive_s *);
706         void    (*dma_exec_cmd)(struct ide_drive_s *, u8);
707         void    (*dma_start)(struct ide_drive_s *);
708         int     (*dma_end)(struct ide_drive_s *);
709         int     (*dma_test_irq)(struct ide_drive_s *);
710         void    (*dma_lost_irq)(struct ide_drive_s *);
711         void    (*dma_timeout)(struct ide_drive_s *);
712         /*
713          * The following method is optional and only required to be
714          * implemented for the SFF-8038i compatible controllers.
715          */
716         u8      (*dma_sff_read_status)(struct hwif_s *);
717 };
718
719 struct ide_host;
720
721 typedef struct hwif_s {
722         struct hwif_s *mate;            /* other hwif from same PCI chip */
723         struct proc_dir_entry *proc;    /* /proc/ide/ directory entry */
724
725         struct ide_host *host;
726
727         char name[6];                   /* name of interface, eg. "ide0" */
728
729         struct ide_io_ports     io_ports;
730
731         unsigned long   sata_scr[SATA_NR_PORTS];
732
733         ide_drive_t     *devices[MAX_DRIVES + 1];
734
735         u8 major;       /* our major number */
736         u8 index;       /* 0 for ide0; 1 for ide1; ... */
737         u8 channel;     /* for dual-port chips: 0=primary, 1=secondary */
738
739         u32 host_flags;
740
741         u8 pio_mask;
742
743         u8 ultra_mask;
744         u8 mwdma_mask;
745         u8 swdma_mask;
746
747         u8 cbl;         /* cable type */
748
749         hwif_chipset_t chipset; /* sub-module for tuning.. */
750
751         struct device *dev;
752
753         ide_ack_intr_t *ack_intr;
754
755         void (*rw_disk)(ide_drive_t *, struct request *);
756
757         const struct ide_tp_ops         *tp_ops;
758         const struct ide_port_ops       *port_ops;
759         const struct ide_dma_ops        *dma_ops;
760
761         /* dma physical region descriptor table (cpu view) */
762         unsigned int    *dmatable_cpu;
763         /* dma physical region descriptor table (dma view) */
764         dma_addr_t      dmatable_dma;
765
766         /* maximum number of PRD table entries */
767         int prd_max_nents;
768         /* PRD entry size in bytes */
769         int prd_ent_size;
770
771         /* Scatter-gather list used to build the above */
772         struct scatterlist *sg_table;
773         int sg_max_nents;               /* Maximum number of entries in it */
774         int sg_nents;                   /* Current number of entries in it */
775         int orig_sg_nents;
776         int sg_dma_direction;           /* dma transfer direction */
777
778         struct ide_task_s task;         /* current command */
779
780         unsigned int nsect;
781         unsigned int nleft;
782         struct scatterlist *cursg;
783         unsigned int cursg_ofs;
784
785         int             rqsize;         /* max sectors per request */
786         int             irq;            /* our irq number */
787
788         unsigned long   dma_base;       /* base addr for dma ports */
789
790         unsigned long   config_data;    /* for use by chipset-specific code */
791         unsigned long   select_data;    /* for use by chipset-specific code */
792
793         unsigned long   extra_base;     /* extra addr for dma ports */
794         unsigned        extra_ports;    /* number of extra dma ports */
795
796         unsigned        present    : 1; /* this interface exists */
797         unsigned        busy       : 1; /* serializes devices on a port */
798
799         struct device           gendev;
800         struct device           *portdev;
801
802         struct completion gendev_rel_comp; /* To deal with device release() */
803
804         void            *hwif_data;     /* extra hwif data */
805
806 #ifdef CONFIG_BLK_DEV_IDEACPI
807         struct ide_acpi_hwif_link *acpidata;
808 #endif
809
810         /* IRQ handler, if active */
811         ide_startstop_t (*handler)(ide_drive_t *);
812
813         /* BOOL: polling active & poll_timeout field valid */
814         unsigned int polling : 1;
815
816         /* current drive */
817         ide_drive_t *cur_dev;
818
819         /* current request */
820         struct request *rq;
821
822         /* failsafe timer */
823         struct timer_list timer;
824         /* timeout value during long polls */
825         unsigned long poll_timeout;
826         /* queried upon timeouts */
827         int (*expiry)(ide_drive_t *);
828
829         int req_gen;
830         int req_gen_timer;
831
832         spinlock_t lock;
833 } ____cacheline_internodealigned_in_smp ide_hwif_t;
834
835 #define MAX_HOST_PORTS 4
836
837 struct ide_host {
838         ide_hwif_t      *ports[MAX_HOST_PORTS + 1];
839         unsigned int    n_ports;
840         struct device   *dev[2];
841
842         int             (*init_chipset)(struct pci_dev *);
843
844         void            (*get_lock)(irq_handler_t, void *);
845         void            (*release_lock)(void);
846
847         irq_handler_t   irq_handler;
848
849         unsigned long   host_flags;
850
851         int             irq_flags;
852
853         void            *host_priv;
854         ide_hwif_t      *cur_port;      /* for hosts requiring serialization */
855
856         /* used for hosts requiring serialization */
857         volatile unsigned long  host_busy;
858 };
859
860 #define IDE_HOST_BUSY 0
861
862 /*
863  *  internal ide interrupt handler type
864  */
865 typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
866 typedef int (ide_expiry_t)(ide_drive_t *);
867
868 /* used by ide-cd, ide-floppy, etc. */
869 typedef void (xfer_func_t)(ide_drive_t *, struct request *rq, void *, unsigned);
870
871 extern struct mutex ide_setting_mtx;
872
873 /*
874  * configurable drive settings
875  */
876
877 #define DS_SYNC (1 << 0)
878
879 struct ide_devset {
880         int             (*get)(ide_drive_t *);
881         int             (*set)(ide_drive_t *, int);
882         unsigned int    flags;
883 };
884
885 #define __DEVSET(_flags, _get, _set) { \
886         .flags  = _flags, \
887         .get    = _get, \
888         .set    = _set, \
889 }
890
891 #define ide_devset_get(name, field) \
892 static int get_##name(ide_drive_t *drive) \
893 { \
894         return drive->field; \
895 }
896
897 #define ide_devset_set(name, field) \
898 static int set_##name(ide_drive_t *drive, int arg) \
899 { \
900         drive->field = arg; \
901         return 0; \
902 }
903
904 #define ide_devset_get_flag(name, flag) \
905 static int get_##name(ide_drive_t *drive) \
906 { \
907         return !!(drive->dev_flags & flag); \
908 }
909
910 #define ide_devset_set_flag(name, flag) \
911 static int set_##name(ide_drive_t *drive, int arg) \
912 { \
913         if (arg) \
914                 drive->dev_flags |= flag; \
915         else \
916                 drive->dev_flags &= ~flag; \
917         return 0; \
918 }
919
920 #define __IDE_DEVSET(_name, _flags, _get, _set) \
921 const struct ide_devset ide_devset_##_name = \
922         __DEVSET(_flags, _get, _set)
923
924 #define IDE_DEVSET(_name, _flags, _get, _set) \
925 static __IDE_DEVSET(_name, _flags, _get, _set)
926
927 #define ide_devset_rw(_name, _func) \
928 IDE_DEVSET(_name, 0, get_##_func, set_##_func)
929
930 #define ide_devset_w(_name, _func) \
931 IDE_DEVSET(_name, 0, NULL, set_##_func)
932
933 #define ide_ext_devset_rw(_name, _func) \
934 __IDE_DEVSET(_name, 0, get_##_func, set_##_func)
935
936 #define ide_ext_devset_rw_sync(_name, _func) \
937 __IDE_DEVSET(_name, DS_SYNC, get_##_func, set_##_func)
938
939 #define ide_decl_devset(_name) \
940 extern const struct ide_devset ide_devset_##_name
941
942 ide_decl_devset(io_32bit);
943 ide_decl_devset(keepsettings);
944 ide_decl_devset(pio_mode);
945 ide_decl_devset(unmaskirq);
946 ide_decl_devset(using_dma);
947
948 #ifdef CONFIG_IDE_PROC_FS
949 /*
950  * /proc/ide interface
951  */
952
953 #define ide_devset_rw_field(_name, _field) \
954 ide_devset_get(_name, _field); \
955 ide_devset_set(_name, _field); \
956 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
957
958 #define ide_devset_rw_flag(_name, _field) \
959 ide_devset_get_flag(_name, _field); \
960 ide_devset_set_flag(_name, _field); \
961 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
962
963 struct ide_proc_devset {
964         const char              *name;
965         const struct ide_devset *setting;
966         int                     min, max;
967         int                     (*mulf)(ide_drive_t *);
968         int                     (*divf)(ide_drive_t *);
969 };
970
971 #define __IDE_PROC_DEVSET(_name, _min, _max, _mulf, _divf) { \
972         .name = __stringify(_name), \
973         .setting = &ide_devset_##_name, \
974         .min = _min, \
975         .max = _max, \
976         .mulf = _mulf, \
977         .divf = _divf, \
978 }
979
980 #define IDE_PROC_DEVSET(_name, _min, _max) \
981 __IDE_PROC_DEVSET(_name, _min, _max, NULL, NULL)
982
983 typedef struct {
984         const char      *name;
985         mode_t          mode;
986         read_proc_t     *read_proc;
987         write_proc_t    *write_proc;
988 } ide_proc_entry_t;
989
990 void proc_ide_create(void);
991 void proc_ide_destroy(void);
992 void ide_proc_register_port(ide_hwif_t *);
993 void ide_proc_port_register_devices(ide_hwif_t *);
994 void ide_proc_unregister_device(ide_drive_t *);
995 void ide_proc_unregister_port(ide_hwif_t *);
996 void ide_proc_register_driver(ide_drive_t *, struct ide_driver *);
997 void ide_proc_unregister_driver(ide_drive_t *, struct ide_driver *);
998
999 read_proc_t proc_ide_read_capacity;
1000 read_proc_t proc_ide_read_geometry;
1001
1002 /*
1003  * Standard exit stuff:
1004  */
1005 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
1006 {                                       \
1007         len -= off;                     \
1008         if (len < count) {              \
1009                 *eof = 1;               \
1010                 if (len <= 0)           \
1011                         return 0;       \
1012         } else                          \
1013                 len = count;            \
1014         *start = page + off;            \
1015         return len;                     \
1016 }
1017 #else
1018 static inline void proc_ide_create(void) { ; }
1019 static inline void proc_ide_destroy(void) { ; }
1020 static inline void ide_proc_register_port(ide_hwif_t *hwif) { ; }
1021 static inline void ide_proc_port_register_devices(ide_hwif_t *hwif) { ; }
1022 static inline void ide_proc_unregister_device(ide_drive_t *drive) { ; }
1023 static inline void ide_proc_unregister_port(ide_hwif_t *hwif) { ; }
1024 static inline void ide_proc_register_driver(ide_drive_t *drive,
1025                                             struct ide_driver *driver) { ; }
1026 static inline void ide_proc_unregister_driver(ide_drive_t *drive,
1027                                               struct ide_driver *driver) { ; }
1028 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
1029 #endif
1030
1031 enum {
1032         /* enter/exit functions */
1033         IDE_DBG_FUNC =                  (1 << 0),
1034         /* sense key/asc handling */
1035         IDE_DBG_SENSE =                 (1 << 1),
1036         /* packet commands handling */
1037         IDE_DBG_PC =                    (1 << 2),
1038         /* request handling */
1039         IDE_DBG_RQ =                    (1 << 3),
1040         /* driver probing/setup */
1041         IDE_DBG_PROBE =                 (1 << 4),
1042 };
1043
1044 /* DRV_NAME has to be defined in the driver before using the macro below */
1045 #define __ide_debug_log(lvl, fmt, args...)                              \
1046 {                                                                       \
1047         if (unlikely(drive->debug_mask & lvl))                          \
1048                 printk(KERN_INFO DRV_NAME ": %s: " fmt "\n",            \
1049                                           __func__, ## args);           \
1050 }
1051
1052 /*
1053  * Power Management state machine (rq->pm->pm_step).
1054  *
1055  * For each step, the core calls ide_start_power_step() first.
1056  * This can return:
1057  *      - ide_stopped : In this case, the core calls us back again unless
1058  *                      step have been set to ide_power_state_completed.
1059  *      - ide_started : In this case, the channel is left busy until an
1060  *                      async event (interrupt) occurs.
1061  * Typically, ide_start_power_step() will issue a taskfile request with
1062  * do_rw_taskfile().
1063  *
1064  * Upon reception of the interrupt, the core will call ide_complete_power_step()
1065  * with the error code if any. This routine should update the step value
1066  * and return. It should not start a new request. The core will call
1067  * ide_start_power_step() for the new step value, unless step have been
1068  * set to IDE_PM_COMPLETED.
1069  */
1070 enum {
1071         IDE_PM_START_SUSPEND,
1072         IDE_PM_FLUSH_CACHE      = IDE_PM_START_SUSPEND,
1073         IDE_PM_STANDBY,
1074
1075         IDE_PM_START_RESUME,
1076         IDE_PM_RESTORE_PIO      = IDE_PM_START_RESUME,
1077         IDE_PM_IDLE,
1078         IDE_PM_RESTORE_DMA,
1079
1080         IDE_PM_COMPLETED,
1081 };
1082
1083 int generic_ide_suspend(struct device *, pm_message_t);
1084 int generic_ide_resume(struct device *);
1085
1086 void ide_complete_power_step(ide_drive_t *, struct request *);
1087 ide_startstop_t ide_start_power_step(ide_drive_t *, struct request *);
1088 void ide_complete_pm_rq(ide_drive_t *, struct request *);
1089 void ide_check_pm_state(ide_drive_t *, struct request *);
1090
1091 /*
1092  * Subdrivers support.
1093  *
1094  * The gendriver.owner field should be set to the module owner of this driver.
1095  * The gendriver.name field should be set to the name of this driver
1096  */
1097 struct ide_driver {
1098         const char                      *version;
1099         ide_startstop_t (*do_request)(ide_drive_t *, struct request *, sector_t);
1100         struct device_driver    gen_driver;
1101         int             (*probe)(ide_drive_t *);
1102         void            (*remove)(ide_drive_t *);
1103         void            (*resume)(ide_drive_t *);
1104         void            (*shutdown)(ide_drive_t *);
1105 #ifdef CONFIG_IDE_PROC_FS
1106         ide_proc_entry_t *              (*proc_entries)(ide_drive_t *);
1107         const struct ide_proc_devset *  (*proc_devsets)(ide_drive_t *);
1108 #endif
1109 };
1110
1111 #define to_ide_driver(drv) container_of(drv, struct ide_driver, gen_driver)
1112
1113 int ide_device_get(ide_drive_t *);
1114 void ide_device_put(ide_drive_t *);
1115
1116 struct ide_ioctl_devset {
1117         unsigned int    get_ioctl;
1118         unsigned int    set_ioctl;
1119         const struct ide_devset *setting;
1120 };
1121
1122 int ide_setting_ioctl(ide_drive_t *, struct block_device *, unsigned int,
1123                       unsigned long, const struct ide_ioctl_devset *);
1124
1125 int generic_ide_ioctl(ide_drive_t *, struct block_device *, unsigned, unsigned long);
1126
1127 extern int ide_vlb_clk;
1128 extern int ide_pci_clk;
1129
1130 int ide_end_request(ide_drive_t *, int, int);
1131 int ide_end_dequeued_request(ide_drive_t *, struct request *, int, int);
1132 void ide_kill_rq(ide_drive_t *, struct request *);
1133
1134 void __ide_set_handler(ide_drive_t *, ide_handler_t *, unsigned int,
1135                        ide_expiry_t *);
1136 void ide_set_handler(ide_drive_t *, ide_handler_t *, unsigned int,
1137                      ide_expiry_t *);
1138
1139 void ide_execute_command(ide_drive_t *, u8, ide_handler_t *, unsigned int,
1140                          ide_expiry_t *);
1141
1142 void ide_execute_pkt_cmd(ide_drive_t *);
1143
1144 void ide_pad_transfer(ide_drive_t *, int, int);
1145
1146 ide_startstop_t ide_error(ide_drive_t *, const char *, u8);
1147
1148 void ide_fix_driveid(u16 *);
1149
1150 extern void ide_fixstring(u8 *, const int, const int);
1151
1152 int ide_busy_sleep(ide_hwif_t *, unsigned long, int);
1153
1154 int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
1155
1156 ide_startstop_t ide_do_park_unpark(ide_drive_t *, struct request *);
1157 ide_startstop_t ide_do_devset(ide_drive_t *, struct request *);
1158
1159 extern ide_startstop_t ide_do_reset (ide_drive_t *);
1160
1161 extern int ide_devset_execute(ide_drive_t *drive,
1162                               const struct ide_devset *setting, int arg);
1163
1164 void ide_complete_task(ide_drive_t *, ide_task_t *, u8, u8);
1165 void ide_complete_rq(ide_drive_t *, u8);
1166
1167 void ide_tf_dump(const char *, struct ide_taskfile *);
1168
1169 void ide_exec_command(ide_hwif_t *, u8);
1170 u8 ide_read_status(ide_hwif_t *);
1171 u8 ide_read_altstatus(ide_hwif_t *);
1172
1173 void ide_set_irq(ide_hwif_t *, int);
1174
1175 void ide_tf_load(ide_drive_t *, ide_task_t *);
1176 void ide_tf_read(ide_drive_t *, ide_task_t *);
1177
1178 void ide_input_data(ide_drive_t *, struct request *, void *, unsigned int);
1179 void ide_output_data(ide_drive_t *, struct request *, void *, unsigned int);
1180
1181 int ide_io_buffers(ide_drive_t *, struct ide_atapi_pc *, unsigned int, int);
1182
1183 extern void SELECT_DRIVE(ide_drive_t *);
1184 void SELECT_MASK(ide_drive_t *, int);
1185
1186 u8 ide_read_error(ide_drive_t *);
1187 void ide_read_bcount_and_ireason(ide_drive_t *, u16 *, u8 *);
1188
1189 int ide_check_atapi_device(ide_drive_t *, const char *);
1190
1191 void ide_init_pc(struct ide_atapi_pc *);
1192
1193 /* Disk head parking */
1194 extern wait_queue_head_t ide_park_wq;
1195 ssize_t ide_park_show(struct device *dev, struct device_attribute *attr,
1196                       char *buf);
1197 ssize_t ide_park_store(struct device *dev, struct device_attribute *attr,
1198                        const char *buf, size_t len);
1199
1200 /*
1201  * Special requests for ide-tape block device strategy routine.
1202  *
1203  * In order to service a character device command, we add special requests to
1204  * the tail of our block device request queue and wait for their completion.
1205  */
1206 enum {
1207         REQ_IDETAPE_PC1         = (1 << 0), /* packet command (first stage) */
1208         REQ_IDETAPE_PC2         = (1 << 1), /* packet command (second stage) */
1209         REQ_IDETAPE_READ        = (1 << 2),
1210         REQ_IDETAPE_WRITE       = (1 << 3),
1211 };
1212
1213 int ide_queue_pc_tail(ide_drive_t *, struct gendisk *, struct ide_atapi_pc *);
1214
1215 int ide_do_test_unit_ready(ide_drive_t *, struct gendisk *);
1216 int ide_do_start_stop(ide_drive_t *, struct gendisk *, int);
1217 int ide_set_media_lock(ide_drive_t *, struct gendisk *, int);
1218 void ide_create_request_sense_cmd(ide_drive_t *, struct ide_atapi_pc *);
1219 void ide_retry_pc(ide_drive_t *, struct gendisk *);
1220
1221 int ide_cd_expiry(ide_drive_t *);
1222
1223 int ide_cd_get_xferlen(struct request *);
1224
1225 ide_startstop_t ide_issue_pc(ide_drive_t *);
1226
1227 ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);
1228
1229 void task_end_request(ide_drive_t *, struct request *, u8);
1230
1231 int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *, u16);
1232 int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);
1233
1234 int ide_taskfile_ioctl(ide_drive_t *, unsigned int, unsigned long);
1235
1236 int ide_dev_read_id(ide_drive_t *, u8, u16 *);
1237
1238 extern int ide_driveid_update(ide_drive_t *);
1239 extern int ide_config_drive_speed(ide_drive_t *, u8);
1240 extern u8 eighty_ninty_three (ide_drive_t *);
1241 extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);
1242
1243 extern int ide_wait_not_busy(ide_hwif_t *hwif, unsigned long timeout);
1244
1245 extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);
1246
1247 extern void ide_timer_expiry(unsigned long);
1248 extern irqreturn_t ide_intr(int irq, void *dev_id);
1249 extern void do_ide_request(struct request_queue *);
1250
1251 void ide_init_disk(struct gendisk *, ide_drive_t *);
1252
1253 #ifdef CONFIG_IDEPCI_PCIBUS_ORDER
1254 extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
1255 #define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
1256 #else
1257 #define ide_pci_register_driver(d) pci_register_driver(d)
1258 #endif
1259
1260 static inline int ide_pci_is_in_compatibility_mode(struct pci_dev *dev)
1261 {
1262         if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE && (dev->class & 5) != 5)
1263                 return 1;
1264         return 0;
1265 }
1266
1267 void ide_pci_setup_ports(struct pci_dev *, const struct ide_port_info *,
1268                          hw_regs_t *, hw_regs_t **);
1269 void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
1270
1271 #ifdef CONFIG_BLK_DEV_IDEDMA_PCI
1272 int ide_pci_set_master(struct pci_dev *, const char *);
1273 unsigned long ide_pci_dma_base(ide_hwif_t *, const struct ide_port_info *);
1274 int ide_pci_check_simplex(ide_hwif_t *, const struct ide_port_info *);
1275 int ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
1276 #else
1277 static inline int ide_hwif_setup_dma(ide_hwif_t *hwif,
1278                                      const struct ide_port_info *d)
1279 {
1280         return -EINVAL;
1281 }
1282 #endif
1283
1284 struct ide_pci_enablebit {
1285         u8      reg;    /* byte pci reg holding the enable-bit */
1286         u8      mask;   /* mask to isolate the enable-bit */
1287         u8      val;    /* value of masked reg when "enabled" */
1288 };
1289
1290 enum {
1291         /* Uses ISA control ports not PCI ones. */
1292         IDE_HFLAG_ISA_PORTS             = (1 << 0),
1293         /* single port device */
1294         IDE_HFLAG_SINGLE                = (1 << 1),
1295         /* don't use legacy PIO blacklist */
1296         IDE_HFLAG_PIO_NO_BLACKLIST      = (1 << 2),
1297         /* set for the second port of QD65xx */
1298         IDE_HFLAG_QD_2ND_PORT           = (1 << 3),
1299         /* use PIO8/9 for prefetch off/on */
1300         IDE_HFLAG_ABUSE_PREFETCH        = (1 << 4),
1301         /* use PIO6/7 for fast-devsel off/on */
1302         IDE_HFLAG_ABUSE_FAST_DEVSEL     = (1 << 5),
1303         /* use 100-102 and 200-202 PIO values to set DMA modes */
1304         IDE_HFLAG_ABUSE_DMA_MODES       = (1 << 6),
1305         /*
1306          * keep DMA setting when programming PIO mode, may be used only
1307          * for hosts which have separate PIO and DMA timings (ie. PMAC)
1308          */
1309         IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
1310         /* program host for the transfer mode after programming device */
1311         IDE_HFLAG_POST_SET_MODE         = (1 << 8),
1312         /* don't program host/device for the transfer mode ("smart" hosts) */
1313         IDE_HFLAG_NO_SET_MODE           = (1 << 9),
1314         /* trust BIOS for programming chipset/device for DMA */
1315         IDE_HFLAG_TRUST_BIOS_FOR_DMA    = (1 << 10),
1316         /* host is CS5510/CS5520 */
1317         IDE_HFLAG_CS5520                = (1 << 11),
1318         /* ATAPI DMA is unsupported */
1319         IDE_HFLAG_NO_ATAPI_DMA          = (1 << 12),
1320         /* set if host is a "non-bootable" controller */
1321         IDE_HFLAG_NON_BOOTABLE          = (1 << 13),
1322         /* host doesn't support DMA */
1323         IDE_HFLAG_NO_DMA                = (1 << 14),
1324         /* check if host is PCI IDE device before allowing DMA */
1325         IDE_HFLAG_NO_AUTODMA            = (1 << 15),
1326         /* host uses MMIO */
1327         IDE_HFLAG_MMIO                  = (1 << 16),
1328         /* no LBA48 */
1329         IDE_HFLAG_NO_LBA48              = (1 << 17),
1330         /* no LBA48 DMA */
1331         IDE_HFLAG_NO_LBA48_DMA          = (1 << 18),
1332         /* data FIFO is cleared by an error */
1333         IDE_HFLAG_ERROR_STOPS_FIFO      = (1 << 19),
1334         /* serialize ports */
1335         IDE_HFLAG_SERIALIZE             = (1 << 20),
1336         /* host is DTC2278 */
1337         IDE_HFLAG_DTC2278               = (1 << 21),
1338         /* 4 devices on a single set of I/O ports */
1339         IDE_HFLAG_4DRIVES               = (1 << 22),
1340         /* host is TRM290 */
1341         IDE_HFLAG_TRM290                = (1 << 23),
1342         /* use 32-bit I/O ops */
1343         IDE_HFLAG_IO_32BIT              = (1 << 24),
1344         /* unmask IRQs */
1345         IDE_HFLAG_UNMASK_IRQS           = (1 << 25),
1346         IDE_HFLAG_BROKEN_ALTSTATUS      = (1 << 26),
1347         /* serialize ports if DMA is possible (for sl82c105) */
1348         IDE_HFLAG_SERIALIZE_DMA         = (1 << 27),
1349         /* force host out of "simplex" mode */
1350         IDE_HFLAG_CLEAR_SIMPLEX         = (1 << 28),
1351         /* DSC overlap is unsupported */
1352         IDE_HFLAG_NO_DSC                = (1 << 29),
1353         /* never use 32-bit I/O ops */
1354         IDE_HFLAG_NO_IO_32BIT           = (1 << 30),
1355         /* never unmask IRQs */
1356         IDE_HFLAG_NO_UNMASK_IRQS        = (1 << 31),
1357 };
1358
1359 #ifdef CONFIG_BLK_DEV_OFFBOARD
1360 # define IDE_HFLAG_OFF_BOARD    0
1361 #else
1362 # define IDE_HFLAG_OFF_BOARD    IDE_HFLAG_NON_BOOTABLE
1363 #endif
1364
1365 struct ide_port_info {
1366         char                    *name;
1367
1368         int                     (*init_chipset)(struct pci_dev *);
1369
1370         void                    (*get_lock)(irq_handler_t, void *);
1371         void                    (*release_lock)(void);
1372
1373         void                    (*init_iops)(ide_hwif_t *);
1374         void                    (*init_hwif)(ide_hwif_t *);
1375         int                     (*init_dma)(ide_hwif_t *,
1376                                             const struct ide_port_info *);
1377
1378         const struct ide_tp_ops         *tp_ops;
1379         const struct ide_port_ops       *port_ops;
1380         const struct ide_dma_ops        *dma_ops;
1381
1382         struct ide_pci_enablebit        enablebits[2];
1383
1384         hwif_chipset_t          chipset;
1385
1386         u16                     max_sectors;    /* if < than the default one */
1387
1388         u32                     host_flags;
1389
1390         int                     irq_flags;
1391
1392         u8                      pio_mask;
1393         u8                      swdma_mask;
1394         u8                      mwdma_mask;
1395         u8                      udma_mask;
1396 };
1397
1398 int ide_pci_init_one(struct pci_dev *, const struct ide_port_info *, void *);
1399 int ide_pci_init_two(struct pci_dev *, struct pci_dev *,
1400                      const struct ide_port_info *, void *);
1401 void ide_pci_remove(struct pci_dev *);
1402
1403 #ifdef CONFIG_PM
1404 int ide_pci_suspend(struct pci_dev *, pm_message_t);
1405 int ide_pci_resume(struct pci_dev *);
1406 #else
1407 #define ide_pci_suspend NULL
1408 #define ide_pci_resume NULL
1409 #endif
1410
1411 void ide_map_sg(ide_drive_t *, struct request *);
1412 void ide_init_sg_cmd(ide_drive_t *, struct request *);
1413
1414 #define BAD_DMA_DRIVE           0
1415 #define GOOD_DMA_DRIVE          1
1416
1417 struct drive_list_entry {
1418         const char *id_model;
1419         const char *id_firmware;
1420 };
1421
1422 int ide_in_drive_list(u16 *, const struct drive_list_entry *);
1423
1424 #ifdef CONFIG_BLK_DEV_IDEDMA
1425 int ide_dma_good_drive(ide_drive_t *);
1426 int __ide_dma_bad_drive(ide_drive_t *);
1427 int ide_id_dma_bug(ide_drive_t *);
1428
1429 u8 ide_find_dma_mode(ide_drive_t *, u8);
1430
1431 static inline u8 ide_max_dma_mode(ide_drive_t *drive)
1432 {
1433         return ide_find_dma_mode(drive, XFER_UDMA_6);
1434 }
1435
1436 void ide_dma_off_quietly(ide_drive_t *);
1437 void ide_dma_off(ide_drive_t *);
1438 void ide_dma_on(ide_drive_t *);
1439 int ide_set_dma(ide_drive_t *);
1440 void ide_check_dma_crc(ide_drive_t *);
1441 ide_startstop_t ide_dma_intr(ide_drive_t *);
1442
1443 int ide_allocate_dma_engine(ide_hwif_t *);
1444 void ide_release_dma_engine(ide_hwif_t *);
1445
1446 int ide_build_sglist(ide_drive_t *, struct request *);
1447 void ide_destroy_dmatable(ide_drive_t *);
1448
1449 #ifdef CONFIG_BLK_DEV_IDEDMA_SFF
1450 int config_drive_for_dma(ide_drive_t *);
1451 extern int ide_build_dmatable(ide_drive_t *, struct request *);
1452 void ide_dma_host_set(ide_drive_t *, int);
1453 extern int ide_dma_setup(ide_drive_t *);
1454 void ide_dma_exec_cmd(ide_drive_t *, u8);
1455 extern void ide_dma_start(ide_drive_t *);
1456 int ide_dma_end(ide_drive_t *);
1457 int ide_dma_test_irq(ide_drive_t *);
1458 u8 ide_dma_sff_read_status(ide_hwif_t *);
1459 extern const struct ide_dma_ops sff_dma_ops;
1460 #else
1461 static inline int config_drive_for_dma(ide_drive_t *drive) { return 0; }
1462 #endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
1463
1464 void ide_dma_lost_irq(ide_drive_t *);
1465 void ide_dma_timeout(ide_drive_t *);
1466 ide_startstop_t ide_dma_timeout_retry(ide_drive_t *, int);
1467
1468 #else
1469 static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
1470 static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
1471 static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
1472 static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
1473 static inline void ide_dma_off(ide_drive_t *drive) { ; }
1474 static inline void ide_dma_on(ide_drive_t *drive) { ; }
1475 static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
1476 static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
1477 static inline void ide_check_dma_crc(ide_drive_t *drive) { ; }
1478 static inline ide_startstop_t ide_dma_timeout_retry(ide_drive_t *drive, int error) { return ide_stopped; }
1479 static inline void ide_release_dma_engine(ide_hwif_t *hwif) { ; }
1480 static inline int ide_build_sglist(ide_drive_t *drive,
1481                                    struct request *rq) { return 0; }
1482 #endif /* CONFIG_BLK_DEV_IDEDMA */
1483
1484 #ifdef CONFIG_BLK_DEV_IDEACPI
1485 int ide_acpi_init(void);
1486 extern int ide_acpi_exec_tfs(ide_drive_t *drive);
1487 extern void ide_acpi_get_timing(ide_hwif_t *hwif);
1488 extern void ide_acpi_push_timing(ide_hwif_t *hwif);
1489 void ide_acpi_init_port(ide_hwif_t *);
1490 void ide_acpi_port_init_devices(ide_hwif_t *);
1491 extern void ide_acpi_set_state(ide_hwif_t *hwif, int on);
1492 #else
1493 static inline int ide_acpi_init(void) { return 0; }
1494 static inline int ide_acpi_exec_tfs(ide_drive_t *drive) { return 0; }
1495 static inline void ide_acpi_get_timing(ide_hwif_t *hwif) { ; }
1496 static inline void ide_acpi_push_timing(ide_hwif_t *hwif) { ; }
1497 static inline void ide_acpi_init_port(ide_hwif_t *hwif) { ; }
1498 static inline void ide_acpi_port_init_devices(ide_hwif_t *hwif) { ; }
1499 static inline void ide_acpi_set_state(ide_hwif_t *hwif, int on) {}
1500 #endif
1501
1502 void ide_register_region(struct gendisk *);
1503 void ide_unregister_region(struct gendisk *);
1504
1505 void ide_undecoded_slave(ide_drive_t *);
1506
1507 void ide_port_apply_params(ide_hwif_t *);
1508 int ide_sysfs_register_port(ide_hwif_t *);
1509
1510 struct ide_host *ide_host_alloc(const struct ide_port_info *, hw_regs_t **);
1511 void ide_host_free(struct ide_host *);
1512 int ide_host_register(struct ide_host *, const struct ide_port_info *,
1513                       hw_regs_t **);
1514 int ide_host_add(const struct ide_port_info *, hw_regs_t **,
1515                  struct ide_host **);
1516 void ide_host_remove(struct ide_host *);
1517 int ide_legacy_device_add(const struct ide_port_info *, unsigned long);
1518 void ide_port_unregister_devices(ide_hwif_t *);
1519 void ide_port_scan(ide_hwif_t *);
1520
1521 static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
1522 {
1523         return hwif->hwif_data;
1524 }
1525
1526 static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
1527 {
1528         hwif->hwif_data = data;
1529 }
1530
1531 extern void ide_toggle_bounce(ide_drive_t *drive, int on);
1532
1533 u64 ide_get_lba_addr(struct ide_taskfile *, int);
1534 u8 ide_dump_status(ide_drive_t *, const char *, u8);
1535
1536 struct ide_timing {
1537         u8  mode;
1538         u8  setup;      /* t1 */
1539         u16 act8b;      /* t2 for 8-bit io */
1540         u16 rec8b;      /* t2i for 8-bit io */
1541         u16 cyc8b;      /* t0 for 8-bit io */
1542         u16 active;     /* t2 or tD */
1543         u16 recover;    /* t2i or tK */
1544         u16 cycle;      /* t0 */
1545         u16 udma;       /* t2CYCTYP/2 */
1546 };
1547
1548 enum {
1549         IDE_TIMING_SETUP        = (1 << 0),
1550         IDE_TIMING_ACT8B        = (1 << 1),
1551         IDE_TIMING_REC8B        = (1 << 2),
1552         IDE_TIMING_CYC8B        = (1 << 3),
1553         IDE_TIMING_8BIT         = IDE_TIMING_ACT8B | IDE_TIMING_REC8B |
1554                                   IDE_TIMING_CYC8B,
1555         IDE_TIMING_ACTIVE       = (1 << 4),
1556         IDE_TIMING_RECOVER      = (1 << 5),
1557         IDE_TIMING_CYCLE        = (1 << 6),
1558         IDE_TIMING_UDMA         = (1 << 7),
1559         IDE_TIMING_ALL          = IDE_TIMING_SETUP | IDE_TIMING_8BIT |
1560                                   IDE_TIMING_ACTIVE | IDE_TIMING_RECOVER |
1561                                   IDE_TIMING_CYCLE | IDE_TIMING_UDMA,
1562 };
1563
1564 struct ide_timing *ide_timing_find_mode(u8);
1565 u16 ide_pio_cycle_time(ide_drive_t *, u8);
1566 void ide_timing_merge(struct ide_timing *, struct ide_timing *,
1567                       struct ide_timing *, unsigned int);
1568 int ide_timing_compute(ide_drive_t *, u8, struct ide_timing *, int, int);
1569
1570 #ifdef CONFIG_IDE_XFER_MODE
1571 int ide_scan_pio_blacklist(char *);
1572 const char *ide_xfer_verbose(u8);
1573 u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
1574 int ide_set_pio_mode(ide_drive_t *, u8);
1575 int ide_set_dma_mode(ide_drive_t *, u8);
1576 void ide_set_pio(ide_drive_t *, u8);
1577 int ide_set_xfer_rate(ide_drive_t *, u8);
1578 #else
1579 static inline void ide_set_pio(ide_drive_t *drive, u8 pio) { ; }
1580 static inline int ide_set_xfer_rate(ide_drive_t *drive, u8 rate) { return -1; }
1581 #endif
1582
1583 static inline void ide_set_max_pio(ide_drive_t *drive)
1584 {
1585         ide_set_pio(drive, 255);
1586 }
1587
1588 char *ide_media_string(ide_drive_t *);
1589
1590 extern struct device_attribute ide_dev_attrs[];
1591 extern struct bus_type ide_bus_type;
1592 extern struct class *ide_port_class;
1593
1594 static inline void ide_dump_identify(u8 *id)
1595 {
1596         print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 2, id, 512, 0);
1597 }
1598
1599 static inline int hwif_to_node(ide_hwif_t *hwif)
1600 {
1601         return hwif->dev ? dev_to_node(hwif->dev) : -1;
1602 }
1603
1604 static inline ide_drive_t *ide_get_pair_dev(ide_drive_t *drive)
1605 {
1606         ide_drive_t *peer = drive->hwif->devices[(drive->dn ^ 1) & 1];
1607
1608         return (peer->dev_flags & IDE_DFLAG_PRESENT) ? peer : NULL;
1609 }
1610
1611 #define ide_port_for_each_dev(i, dev, port) \
1612         for ((i) = 0; ((dev) = (port)->devices[i]) || (i) < MAX_DRIVES; (i)++)
1613
1614 #define ide_port_for_each_present_dev(i, dev, port) \
1615         for ((i) = 0; ((dev) = (port)->devices[i]) || (i) < MAX_DRIVES; (i)++) \
1616                 if ((dev)->dev_flags & IDE_DFLAG_PRESENT)
1617
1618 #define ide_host_for_each_port(i, port, host) \
1619         for ((i) = 0; ((port) = (host)->ports[i]) || (i) < MAX_HOST_PORTS; (i)++)
1620
1621 #endif /* _IDE_H */