fs/Kconfig: move fuse out

[safe/jmp/linux-2.6] / fs / Kconfig

#
# File system configuration
#

menu "File systems"

if BLOCK

source "fs/ext2/Kconfig"
source "fs/ext3/Kconfig"
source "fs/ext4/Kconfig"

config FS_XIP
# execute in place
        bool
        depends on EXT2_FS_XIP
        default y

source "fs/jbd/Kconfig"
source "fs/jbd2/Kconfig"

config FS_MBCACHE
# Meta block cache for Extended Attributes (ext2/ext3/ext4)
        tristate
        default y if EXT2_FS=y && EXT2_FS_XATTR
        default y if EXT3_FS=y && EXT3_FS_XATTR
        default y if EXT4_FS=y && EXT4_FS_XATTR
        default m if EXT2_FS_XATTR || EXT3_FS_XATTR || EXT4_FS_XATTR

source "fs/reiserfs/Kconfig"
source "fs/jfs/Kconfig"

config FS_POSIX_ACL
# Posix ACL utility routines (for now, only ext2/ext3/jfs/reiserfs/nfs4)
#
# NOTE: you can implement Posix ACLs without these helpers (XFS does).
#       Never use this symbol for ifdefs.
#
        bool
        default n

config FILE_LOCKING
        bool "Enable POSIX file locking API" if EMBEDDED
        default y
        help
          This option enables standard file locking support, required
          for filesystems like NFS and for the flock() system
          call. Disabling this option saves about 11k.

source "fs/xfs/Kconfig"
source "fs/gfs2/Kconfig"
source "fs/ocfs2/Kconfig"
source "fs/btrfs/Kconfig"

endif # BLOCK

source "fs/notify/Kconfig"

config QUOTA
        bool "Quota support"
        help
          If you say Y here, you will be able to set per user limits for disk
          usage (also called disk quotas). Currently, it works for the
          ext2, ext3, and reiserfs file system. ext3 also supports journalled
          quotas for which you don't need to run quotacheck(8) after an unclean
          shutdown.
          For further details, read the Quota mini-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, or the documentation provided
          with the quota tools. Probably the quota support is only useful for
          multi user systems. If unsure, say N.

config QUOTA_NETLINK_INTERFACE
        bool "Report quota messages through netlink interface"
        depends on QUOTA && NET
        help
          If you say Y here, quota warnings (about exceeding softlimit, reaching
          hardlimit, etc.) will be reported through netlink interface. If unsure,
          say Y.

config PRINT_QUOTA_WARNING
        bool "Print quota warnings to console (OBSOLETE)"
        depends on QUOTA
        default y
        help
          If you say Y here, quota warnings (about exceeding softlimit, reaching
          hardlimit, etc.) will be printed to the process' controlling terminal.
          Note that this behavior is currently deprecated and may go away in
          future. Please use notification via netlink socket instead.

# Generic support for tree structured quota files. Seleted when needed.
config QUOTA_TREE
         tristate

config QFMT_V1
        tristate "Old quota format support"
        depends on QUOTA
        help
          This quota format was (is) used by kernels earlier than 2.4.22. If
          you have quota working and you don't want to convert to new quota
          format say Y here.

config QFMT_V2
        tristate "Quota format v2 support"
        depends on QUOTA
        select QUOTA_TREE
        help
          This quota format allows using quotas with 32-bit UIDs/GIDs. If you
          need this functionality say Y here.

config QUOTACTL
        bool
        depends on XFS_QUOTA || QUOTA
        default y

source "fs/autofs/Kconfig"
source "fs/autofs4/Kconfig"
source "fs/fuse/Kconfig"

config GENERIC_ACL
        bool
        select FS_POSIX_ACL

if BLOCK
menu "CD-ROM/DVD Filesystems"

config ISO9660_FS
        tristate "ISO 9660 CDROM file system support"
        help
          This is the standard file system used on CD-ROMs.  It was previously
          known as "High Sierra File System" and is called "hsfs" on other
          Unix systems.  The so-called Rock-Ridge extensions which allow for
          long Unix filenames and symbolic links are also supported by this
          driver.  If you have a CD-ROM drive and want to do more with it than
          just listen to audio CDs and watch its LEDs, say Y (and read
          <file:Documentation/filesystems/isofs.txt> and the CD-ROM-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>), thereby
          enlarging your kernel by about 27 KB; otherwise say N.

          To compile this file system support as a module, choose M here: the
          module will be called isofs.

config JOLIET
        bool "Microsoft Joliet CDROM extensions"
        depends on ISO9660_FS
        select NLS
        help
          Joliet is a Microsoft extension for the ISO 9660 CD-ROM file system
          which allows for long filenames in unicode format (unicode is the
          new 16 bit character code, successor to ASCII, which encodes the
          characters of almost all languages of the world; see
          <http://www.unicode.org/> for more information).  Say Y here if you
          want to be able to read Joliet CD-ROMs under Linux.

config ZISOFS
        bool "Transparent decompression extension"
        depends on ISO9660_FS
        select ZLIB_INFLATE
        help
          This is a Linux-specific extension to RockRidge which lets you store
          data in compressed form on a CD-ROM and have it transparently
          decompressed when the CD-ROM is accessed.  See
          <http://www.kernel.org/pub/linux/utils/fs/zisofs/> for the tools
          necessary to create such a filesystem.  Say Y here if you want to be
          able to read such compressed CD-ROMs.

config UDF_FS
        tristate "UDF file system support"
        select CRC_ITU_T
        help
          This is the new file system used on some CD-ROMs and DVDs. Say Y if
          you intend to mount DVD discs or CDRW's written in packet mode, or
          if written to by other UDF utilities, such as DirectCD.
          Please read <file:Documentation/filesystems/udf.txt>.

          To compile this file system support as a module, choose M here: the
          module will be called udf.

          If unsure, say N.

config UDF_NLS
        bool
        default y
        depends on (UDF_FS=m && NLS) || (UDF_FS=y && NLS=y)

endmenu
endif # BLOCK

if BLOCK
menu "DOS/FAT/NT Filesystems"

config FAT_FS
        tristate
        select NLS
        help
          If you want to use one of the FAT-based file systems (the MS-DOS and
          VFAT (Windows 95) file systems), then you must say Y or M here
          to include FAT support. You will then be able to mount partitions or
          diskettes with FAT-based file systems and transparently access the
          files on them, i.e. MSDOS files will look and behave just like all
          other Unix files.

          This FAT support is not a file system in itself, it only provides
          the foundation for the other file systems. You will have to say Y or
          M to at least one of "MSDOS fs support" or "VFAT fs support" in
          order to make use of it.

          Another way to read and write MSDOS floppies and hard drive
          partitions from within Linux (but not transparently) is with the
          mtools ("man mtools") program suite. You don't need to say Y here in
          order to do that.

          If you need to move large files on floppies between a DOS and a
          Linux box, say Y here, mount the floppy under Linux with an MSDOS
          file system and use GNU tar's M option. GNU tar is a program
          available for Unix and DOS ("man tar" or "info tar").

          The FAT support will enlarge your kernel by about 37 KB. If unsure,
          say Y.

          To compile this as a module, choose M here: the module will be called
          fat.  Note that if you compile the FAT support as a module, you
          cannot compile any of the FAT-based file systems into the kernel
          -- they will have to be modules as well.

config MSDOS_FS
        tristate "MSDOS fs support"
        select FAT_FS
        help
          This allows you to mount MSDOS partitions of your hard drive (unless
          they are compressed; to access compressed MSDOS partitions under
          Linux, you can either use the DOS emulator DOSEMU, described in the
          DOSEMU-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, or try dmsdosfs in
          <ftp://ibiblio.org/pub/Linux/system/filesystems/dosfs/>. If you
          intend to use dosemu with a non-compressed MSDOS partition, say Y
          here) and MSDOS floppies. This means that file access becomes
          transparent, i.e. the MSDOS files look and behave just like all
          other Unix files.

          If you have Windows 95 or Windows NT installed on your MSDOS
          partitions, you should use the VFAT file system (say Y to "VFAT fs
          support" below), or you will not be able to see the long filenames
          generated by Windows 95 / Windows NT.

          This option will enlarge your kernel by about 7 KB. If unsure,
          answer Y. This will only work if you said Y to "DOS FAT fs support"
          as well. To compile this as a module, choose M here: the module will
          be called msdos.

config VFAT_FS
        tristate "VFAT (Windows-95) fs support"
        select FAT_FS
        help
          This option provides support for normal Windows file systems with
          long filenames.  That includes non-compressed FAT-based file systems
          used by Windows 95, Windows 98, Windows NT 4.0, and the Unix
          programs from the mtools package.

          The VFAT support enlarges your kernel by about 10 KB and it only
          works if you said Y to the "DOS FAT fs support" above.  Please read
          the file <file:Documentation/filesystems/vfat.txt> for details.  If
          unsure, say Y.

          To compile this as a module, choose M here: the module will be called
          vfat.

config FAT_DEFAULT_CODEPAGE
        int "Default codepage for FAT"
        depends on MSDOS_FS || VFAT_FS
        default 437
        help
          This option should be set to the codepage of your FAT filesystems.
          It can be overridden with the "codepage" mount option.
          See <file:Documentation/filesystems/vfat.txt> for more information.

config FAT_DEFAULT_IOCHARSET
        string "Default iocharset for FAT"
        depends on VFAT_FS
        default "iso8859-1"
        help
          Set this to the default input/output character set you'd
          like FAT to use. It should probably match the character set
          that most of your FAT filesystems use, and can be overridden
          with the "iocharset" mount option for FAT filesystems.
          Note that "utf8" is not recommended for FAT filesystems.
          If unsure, you shouldn't set "utf8" here.
          See <file:Documentation/filesystems/vfat.txt> for more information.

config NTFS_FS
        tristate "NTFS file system support"
        select NLS
        help
          NTFS is the file system of Microsoft Windows NT, 2000, XP and 2003.

          Saying Y or M here enables read support.  There is partial, but
          safe, write support available.  For write support you must also
          say Y to "NTFS write support" below.

          There are also a number of user-space tools available, called
          ntfsprogs.  These include ntfsundelete and ntfsresize, that work
          without NTFS support enabled in the kernel.

          This is a rewrite from scratch of Linux NTFS support and replaced
          the old NTFS code starting with Linux 2.5.11.  A backport to
          the Linux 2.4 kernel series is separately available as a patch
          from the project web site.

          For more information see <file:Documentation/filesystems/ntfs.txt>
          and <http://www.linux-ntfs.org/>.

          To compile this file system support as a module, choose M here: the
          module will be called ntfs.

          If you are not using Windows NT, 2000, XP or 2003 in addition to
          Linux on your computer it is safe to say N.

config NTFS_DEBUG
        bool "NTFS debugging support"
        depends on NTFS_FS
        help
          If you are experiencing any problems with the NTFS file system, say
          Y here.  This will result in additional consistency checks to be
          performed by the driver as well as additional debugging messages to
          be written to the system log.  Note that debugging messages are
          disabled by default.  To enable them, supply the option debug_msgs=1
          at the kernel command line when booting the kernel or as an option
          to insmod when loading the ntfs module.  Once the driver is active,
          you can enable debugging messages by doing (as root):
          echo 1 > /proc/sys/fs/ntfs-debug
          Replacing the "1" with "0" would disable debug messages.

          If you leave debugging messages disabled, this results in little
          overhead, but enabling debug messages results in very significant
          slowdown of the system.

          When reporting bugs, please try to have available a full dump of
          debugging messages while the misbehaviour was occurring.

config NTFS_RW
        bool "NTFS write support"
        depends on NTFS_FS
        help
          This enables the partial, but safe, write support in the NTFS driver.

          The only supported operation is overwriting existing files, without
          changing the file length.  No file or directory creation, deletion or
          renaming is possible.  Note only non-resident files can be written to
          so you may find that some very small files (<500 bytes or so) cannot
          be written to.

          While we cannot guarantee that it will not damage any data, we have
          so far not received a single report where the driver would have
          damaged someones data so we assume it is perfectly safe to use.

          Note:  While write support is safe in this version (a rewrite from
          scratch of the NTFS support), it should be noted that the old NTFS
          write support, included in Linux 2.5.10 and before (since 1997),
          is not safe.

          This is currently useful with TopologiLinux.  TopologiLinux is run
          on top of any DOS/Microsoft Windows system without partitioning your
          hard disk.  Unlike other Linux distributions TopologiLinux does not
          need its own partition.  For more information see
          <http://topologi-linux.sourceforge.net/>

          It is perfectly safe to say N here.

endmenu
endif # BLOCK

menu "Pseudo filesystems"

source "fs/proc/Kconfig"

config SYSFS
        bool "sysfs file system support" if EMBEDDED
        default y
        help
        The sysfs filesystem is a virtual filesystem that the kernel uses to
        export internal kernel objects, their attributes, and their
        relationships to one another.

        Users can use sysfs to ascertain useful information about the running
        kernel, such as the devices the kernel has discovered on each bus and
        which driver each is bound to. sysfs can also be used to tune devices
        and other kernel subsystems.

        Some system agents rely on the information in sysfs to operate.
        /sbin/hotplug uses device and object attributes in sysfs to assist in
        delegating policy decisions, like persistently naming devices.

        sysfs is currently used by the block subsystem to mount the root
        partition.  If sysfs is disabled you must specify the boot device on
        the kernel boot command line via its major and minor numbers.  For
        example, "root=03:01" for /dev/hda1.

        Designers of embedded systems may wish to say N here to conserve space.

config TMPFS
        bool "Virtual memory file system support (former shm fs)"
        help
          Tmpfs is a file system which keeps all files in virtual memory.

          Everything in tmpfs is temporary in the sense that no files will be
          created on your hard drive. The files live in memory and swap
          space. If you unmount a tmpfs instance, everything stored therein is
          lost.

          See <file:Documentation/filesystems/tmpfs.txt> for details.

config TMPFS_POSIX_ACL
        bool "Tmpfs POSIX Access Control Lists"
        depends on TMPFS
        select GENERIC_ACL
        help
          POSIX Access Control Lists (ACLs) support permissions for users and
          groups beyond the owner/group/world scheme.

          To learn more about Access Control Lists, visit the POSIX ACLs for
          Linux website <http://acl.bestbits.at/>.

          If you don't know what Access Control Lists are, say N.

config HUGETLBFS
        bool "HugeTLB file system support"
        depends on X86 || IA64 || PPC64 || SPARC64 || (SUPERH && MMU) || \
                   (S390 && 64BIT) || BROKEN
        help
          hugetlbfs is a filesystem backing for HugeTLB pages, based on
          ramfs. For architectures that support it, say Y here and read
          <file:Documentation/vm/hugetlbpage.txt> for details.

          If unsure, say N.

config HUGETLB_PAGE
        def_bool HUGETLBFS

config CONFIGFS_FS
        tristate "Userspace-driven configuration filesystem"
        depends on SYSFS
        help
          configfs is a ram-based filesystem that provides the converse
          of sysfs's functionality. Where sysfs is a filesystem-based
          view of kernel objects, configfs is a filesystem-based manager
          of kernel objects, or config_items.

          Both sysfs and configfs can and should exist together on the
          same system. One is not a replacement for the other.

endmenu

menuconfig MISC_FILESYSTEMS
        bool "Miscellaneous filesystems"
        default y
        ---help---
          Say Y here to get to see options for various miscellaneous
          filesystems, such as filesystems that came from other
          operating systems.

          This option alone does not add any kernel code.

          If you say N, all options in this submenu will be skipped and
          disabled; if unsure, say Y here.

if MISC_FILESYSTEMS

config ADFS_FS
        tristate "ADFS file system support (EXPERIMENTAL)"
        depends on BLOCK && EXPERIMENTAL
        help
          The Acorn Disc Filing System is the standard file system of the
          RiscOS operating system which runs on Acorn's ARM-based Risc PC
          systems and the Acorn Archimedes range of machines. If you say Y
          here, Linux will be able to read from ADFS partitions on hard drives
          and from ADFS-formatted floppy discs. If you also want to be able to
          write to those devices, say Y to "ADFS write support" below.

          The ADFS partition should be the first partition (i.e.,
          /dev/[hs]d?1) on each of your drives. Please read the file
          <file:Documentation/filesystems/adfs.txt> for further details.

          To compile this code as a module, choose M here: the module will be
          called adfs.

          If unsure, say N.

config ADFS_FS_RW
        bool "ADFS write support (DANGEROUS)"
        depends on ADFS_FS
        help
          If you say Y here, you will be able to write to ADFS partitions on
          hard drives and ADFS-formatted floppy disks. This is experimental
          codes, so if you're unsure, say N.

config AFFS_FS
        tristate "Amiga FFS file system support (EXPERIMENTAL)"
        depends on BLOCK && EXPERIMENTAL
        help
          The Fast File System (FFS) is the common file system used on hard
          disks by Amiga(tm) systems since AmigaOS Version 1.3 (34.20).  Say Y
          if you want to be able to read and write files from and to an Amiga
          FFS partition on your hard drive.  Amiga floppies however cannot be
          read with this driver due to an incompatibility of the floppy
          controller used in an Amiga and the standard floppy controller in
          PCs and workstations. Read <file:Documentation/filesystems/affs.txt>
          and <file:fs/affs/Changes>.

          With this driver you can also mount disk files used by Bernd
          Schmidt's Un*X Amiga Emulator
          (<http://www.freiburg.linux.de/~uae/>).
          If you want to do this, you will also need to say Y or M to "Loop
          device support", above.

          To compile this file system support as a module, choose M here: the
          module will be called affs.  If unsure, say N.

config ECRYPT_FS
        tristate "eCrypt filesystem layer support (EXPERIMENTAL)"
        depends on EXPERIMENTAL && KEYS && CRYPTO && NET
        help
          Encrypted filesystem that operates on the VFS layer.  See
          <file:Documentation/filesystems/ecryptfs.txt> to learn more about
          eCryptfs.  Userspace components are required and can be
          obtained from <http://ecryptfs.sf.net>.

          To compile this file system support as a module, choose M here: the
          module will be called ecryptfs.

config HFS_FS
        tristate "Apple Macintosh file system support (EXPERIMENTAL)"
        depends on BLOCK && EXPERIMENTAL
        select NLS
        help
          If you say Y here, you will be able to mount Macintosh-formatted
          floppy disks and hard drive partitions with full read-write access.
          Please read <file:Documentation/filesystems/hfs.txt> to learn about
          the available mount options.

          To compile this file system support as a module, choose M here: the
          module will be called hfs.

config HFSPLUS_FS
        tristate "Apple Extended HFS file system support"
        depends on BLOCK
        select NLS
        select NLS_UTF8
        help
          If you say Y here, you will be able to mount extended format
          Macintosh-formatted hard drive partitions with full read-write access.

          This file system is often called HFS+ and was introduced with
          MacOS 8. It includes all Mac specific filesystem data such as
          data forks and creator codes, but it also has several UNIX
          style features such as file ownership and permissions.

config BEFS_FS
        tristate "BeOS file system (BeFS) support (read only) (EXPERIMENTAL)"
        depends on BLOCK && EXPERIMENTAL
        select NLS
        help
          The BeOS File System (BeFS) is the native file system of Be, Inc's
          BeOS. Notable features include support for arbitrary attributes
          on files and directories, and database-like indices on selected
          attributes. (Also note that this driver doesn't make those features
          available at this time). It is a 64 bit filesystem, so it supports
          extremely large volumes and files.

          If you use this filesystem, you should also say Y to at least one
          of the NLS (native language support) options below.

          If you don't know what this is about, say N.

          To compile this as a module, choose M here: the module will be
          called befs.

config BEFS_DEBUG
        bool "Debug BeFS"
        depends on BEFS_FS
        help
          If you say Y here, you can use the 'debug' mount option to enable
          debugging output from the driver.

config BFS_FS
        tristate "BFS file system support (EXPERIMENTAL)"
        depends on BLOCK && EXPERIMENTAL
        help
          Boot File System (BFS) is a file system used under SCO UnixWare to
          allow the bootloader access to the kernel image and other important
          files during the boot process.  It is usually mounted under /stand
          and corresponds to the slice marked as "STAND" in the UnixWare
          partition.  You should say Y if you want to read or write the files
          on your /stand slice from within Linux.  You then also need to say Y
          to "UnixWare slices support", below.  More information about the BFS
          file system is contained in the file
          <file:Documentation/filesystems/bfs.txt>.

          If you don't know what this is about, say N.

          To compile this as a module, choose M here: the module will be called
          bfs.  Note that the file system of your root partition (the one
          containing the directory /) cannot be compiled as a module.



config EFS_FS
        tristate "EFS file system support (read only) (EXPERIMENTAL)"
        depends on BLOCK && EXPERIMENTAL
        help
          EFS is an older file system used for non-ISO9660 CD-ROMs and hard
          disk partitions by SGI's IRIX operating system (IRIX 6.0 and newer
          uses the XFS file system for hard disk partitions however).

          This implementation only offers read-only access. If you don't know
          what all this is about, it's safe to say N. For more information
          about EFS see its home page at <http://aeschi.ch.eu.org/efs/>.

          To compile the EFS file system support as a module, choose M here: the
          module will be called efs.

source "fs/jffs2/Kconfig"
# UBIFS File system configuration
source "fs/ubifs/Kconfig"

config CRAMFS
        tristate "Compressed ROM file system support (cramfs)"
        depends on BLOCK
        select ZLIB_INFLATE
        help
          Saying Y here includes support for CramFs (Compressed ROM File
          System).  CramFs is designed to be a simple, small, and compressed
          file system for ROM based embedded systems.  CramFs is read-only,
          limited to 256MB file systems (with 16MB files), and doesn't support
          16/32 bits uid/gid, hard links and timestamps.

          See <file:Documentation/filesystems/cramfs.txt> and
          <file:fs/cramfs/README> for further information.

          To compile this as a module, choose M here: the module will be called
          cramfs.  Note that the root file system (the one containing the
          directory /) cannot be compiled as a module.

          If unsure, say N.

config SQUASHFS
        tristate "SquashFS 4.0 - Squashed file system support"
        depends on BLOCK
        select ZLIB_INFLATE
        help
          Saying Y here includes support for SquashFS 4.0 (a Compressed
          Read-Only File System).  Squashfs is a highly compressed read-only
          filesystem for Linux.  It uses zlib compression to compress both
          files, inodes and directories.  Inodes in the system are very small
          and all blocks are packed to minimise data overhead. Block sizes
          greater than 4K are supported up to a maximum of 1 Mbytes (default
          block size 128K).  SquashFS 4.0 supports 64 bit filesystems and files
          (larger than 4GB), full uid/gid information, hard links and
          timestamps.  

          Squashfs is intended for general read-only filesystem use, for
          archival use (i.e. in cases where a .tar.gz file may be used), and in
          embedded systems where low overhead is needed.  Further information
          and tools are available from http://squashfs.sourceforge.net.

          If you want to compile this as a module ( = code which can be
          inserted in and removed from the running kernel whenever you want),
          say M here and read <file:Documentation/modules.txt>.  The module
          will be called squashfs.  Note that the root file system (the one
          containing the directory /) cannot be compiled as a module.

          If unsure, say N.

config SQUASHFS_EMBEDDED

        bool "Additional option for memory-constrained systems" 
        depends on SQUASHFS
        default n
        help
          Saying Y here allows you to specify cache size.

          If unsure, say N.

config SQUASHFS_FRAGMENT_CACHE_SIZE
        int "Number of fragments cached" if SQUASHFS_EMBEDDED
        depends on SQUASHFS
        default "3"
        help
          By default SquashFS caches the last 3 fragments read from
          the filesystem.  Increasing this amount may mean SquashFS
          has to re-read fragments less often from disk, at the expense
          of extra system memory.  Decreasing this amount will mean
          SquashFS uses less memory at the expense of extra reads from disk.

          Note there must be at least one cached fragment.  Anything
          much more than three will probably not make much difference.

config VXFS_FS
        tristate "FreeVxFS file system support (VERITAS VxFS(TM) compatible)"
        depends on BLOCK
        help
          FreeVxFS is a file system driver that support the VERITAS VxFS(TM)
          file system format.  VERITAS VxFS(TM) is the standard file system
          of SCO UnixWare (and possibly others) and optionally available
          for Sunsoft Solaris, HP-UX and many other operating systems.
          Currently only readonly access is supported.

          NOTE: the file system type as used by mount(1), mount(2) and
          fstab(5) is 'vxfs' as it describes the file system format, not
          the actual driver.

          To compile this as a module, choose M here: the module will be
          called freevxfs.  If unsure, say N.

config MINIX_FS
        tristate "Minix file system support"
        depends on BLOCK
        help
          Minix is a simple operating system used in many classes about OS's.
          The minix file system (method to organize files on a hard disk
          partition or a floppy disk) was the original file system for Linux,
          but has been superseded by the second extended file system ext2fs.
          You don't want to use the minix file system on your hard disk
          because of certain built-in restrictions, but it is sometimes found
          on older Linux floppy disks.  This option will enlarge your kernel
          by about 28 KB. If unsure, say N.

          To compile this file system support as a module, choose M here: the
          module will be called minix.  Note that the file system of your root
          partition (the one containing the directory /) cannot be compiled as
          a module.

config OMFS_FS
        tristate "SonicBlue Optimized MPEG File System support"
        depends on BLOCK
        select CRC_ITU_T
        help
          This is the proprietary file system used by the Rio Karma music
          player and ReplayTV DVR.  Despite the name, this filesystem is not
          more efficient than a standard FS for MPEG files, in fact likely
          the opposite is true.  Say Y if you have either of these devices
          and wish to mount its disk.

          To compile this file system support as a module, choose M here: the
          module will be called omfs.  If unsure, say N.

config HPFS_FS
        tristate "OS/2 HPFS file system support"
        depends on BLOCK
        help
          OS/2 is IBM's operating system for PC's, the same as Warp, and HPFS
          is the file system used for organizing files on OS/2 hard disk
          partitions. Say Y if you want to be able to read files from and
          write files to an OS/2 HPFS partition on your hard drive. OS/2
          floppies however are in regular MSDOS format, so you don't need this
          option in order to be able to read them. Read
          <file:Documentation/filesystems/hpfs.txt>.

          To compile this file system support as a module, choose M here: the
          module will be called hpfs.  If unsure, say N.


config QNX4FS_FS
        tristate "QNX4 file system support (read only)"
        depends on BLOCK
        help
          This is the file system used by the real-time operating systems
          QNX 4 and QNX 6 (the latter is also called QNX RTP).
          Further information is available at <http://www.qnx.com/>.
          Say Y if you intend to mount QNX hard disks or floppies.
          Unless you say Y to "QNX4FS read-write support" below, you will
          only be able to read these file systems.

          To compile this file system support as a module, choose M here: the
          module will be called qnx4.

          If you don't know whether you need it, then you don't need it:
          answer N.

config QNX4FS_RW
        bool "QNX4FS write support (DANGEROUS)"
        depends on QNX4FS_FS && EXPERIMENTAL && BROKEN
        help
          Say Y if you want to test write support for QNX4 file systems.

          It's currently broken, so for now:
          answer N.

config ROMFS_FS
        tristate "ROM file system support"
        depends on BLOCK
        ---help---
          This is a very small read-only file system mainly intended for
          initial ram disks of installation disks, but it could be used for
          other read-only media as well.  Read
          <file:Documentation/filesystems/romfs.txt> for details.

          To compile this file system support as a module, choose M here: the
          module will be called romfs.  Note that the file system of your
          root partition (the one containing the directory /) cannot be a
          module.

          If you don't know whether you need it, then you don't need it:
          answer N.


config SYSV_FS
        tristate "System V/Xenix/V7/Coherent file system support"
        depends on BLOCK
        help
          SCO, Xenix and Coherent are commercial Unix systems for Intel
          machines, and Version 7 was used on the DEC PDP-11. Saying Y
          here would allow you to read from their floppies and hard disk
          partitions.

          If you have floppies or hard disk partitions like that, it is likely
          that they contain binaries from those other Unix systems; in order
          to run these binaries, you will want to install linux-abi which is
          a set of kernel modules that lets you run SCO, Xenix, Wyse,
          UnixWare, Dell Unix and System V programs under Linux.  It is
          available via FTP (user: ftp) from
          <ftp://ftp.openlinux.org/pub/people/hch/linux-abi/>).
          NOTE: that will work only for binaries from Intel-based systems;
          PDP ones will have to wait until somebody ports Linux to -11 ;-)

          If you only intend to mount files from some other Unix over the
          network using NFS, you don't need the System V file system support
          (but you need NFS file system support obviously).

          Note that this option is generally not needed for floppies, since a
          good portable way to transport files and directories between unixes
          (and even other operating systems) is given by the tar program ("man
          tar" or preferably "info tar").  Note also that this option has
          nothing whatsoever to do with the option "System V IPC". Read about
          the System V file system in
          <file:Documentation/filesystems/sysv-fs.txt>.
          Saying Y here will enlarge your kernel by about 27 KB.

          To compile this as a module, choose M here: the module will be called
          sysv.

          If you haven't heard about all of this before, it's safe to say N.


config UFS_FS
        tristate "UFS file system support (read only)"
        depends on BLOCK
        help
          BSD and derivate versions of Unix (such as SunOS, FreeBSD, NetBSD,
          OpenBSD and NeXTstep) use a file system called UFS. Some System V
          Unixes can create and mount hard disk partitions and diskettes using
          this file system as well. Saying Y here will allow you to read from
          these partitions; if you also want to write to them, say Y to the
          experimental "UFS file system write support", below. Please read the
          file <file:Documentation/filesystems/ufs.txt> for more information.

          The recently released UFS2 variant (used in FreeBSD 5.x) is
          READ-ONLY supported.

          Note that this option is generally not needed for floppies, since a
          good portable way to transport files and directories between unixes
          (and even other operating systems) is given by the tar program ("man
          tar" or preferably "info tar").

          When accessing NeXTstep files, you may need to convert them from the
          NeXT character set to the Latin1 character set; use the program
          recode ("info recode") for this purpose.

          To compile the UFS file system support as a module, choose M here: the
          module will be called ufs.

          If you haven't heard about all of this before, it's safe to say N.

config UFS_FS_WRITE
        bool "UFS file system write support (DANGEROUS)"
        depends on UFS_FS && EXPERIMENTAL
        help
          Say Y here if you want to try writing to UFS partitions. This is
          experimental, so you should back up your UFS partitions beforehand.

config UFS_DEBUG
        bool "UFS debugging"
        depends on UFS_FS
        help
          If you are experiencing any problems with the UFS filesystem, say
          Y here.  This will result in _many_ additional debugging messages to be
          written to the system log.

endif # MISC_FILESYSTEMS

menuconfig NETWORK_FILESYSTEMS
        bool "Network File Systems"
        default y
        depends on NET
        ---help---
          Say Y here to get to see options for network filesystems and
          filesystem-related networking code, such as NFS daemon and
          RPCSEC security modules.

          This option alone does not add any kernel code.

          If you say N, all options in this submenu will be skipped and
          disabled; if unsure, say Y here.

if NETWORK_FILESYSTEMS

config NFS_FS
        tristate "NFS client support"
        depends on INET
        select LOCKD
        select SUNRPC
        select NFS_ACL_SUPPORT if NFS_V3_ACL
        help
          Choose Y here if you want to access files residing on other
          computers using Sun's Network File System protocol.  To compile
          this file system support as a module, choose M here: the module
          will be called nfs.

          To mount file systems exported by NFS servers, you also need to
          install the user space mount.nfs command which can be found in
          the Linux nfs-utils package, available from http://linux-nfs.org/.
          Information about using the mount command is available in the
          mount(8) man page.  More detail about the Linux NFS client
          implementation is available via the nfs(5) man page.

          Below you can choose which versions of the NFS protocol are
          available in the kernel to mount NFS servers.  Support for NFS
          version 2 (RFC 1094) is always available when NFS_FS is selected.

          To configure a system which mounts its root file system via NFS
          at boot time, say Y here, select "Kernel level IP
          autoconfiguration" in the NETWORK menu, and select "Root file
          system on NFS" below.  You cannot compile this file system as a
          module in this case.

          If unsure, say N.

config NFS_V3
        bool "NFS client support for NFS version 3"
        depends on NFS_FS
        help
          This option enables support for version 3 of the NFS protocol
          (RFC 1813) in the kernel's NFS client.

          If unsure, say Y.

config NFS_V3_ACL
        bool "NFS client support for the NFSv3 ACL protocol extension"
        depends on NFS_V3
        help
          Some NFS servers support an auxiliary NFSv3 ACL protocol that
          Sun added to Solaris but never became an official part of the
          NFS version 3 protocol.  This protocol extension allows
          applications on NFS clients to manipulate POSIX Access Control
          Lists on files residing on NFS servers.  NFS servers enforce
          ACLs on local files whether this protocol is available or not.

          Choose Y here if your NFS server supports the Solaris NFSv3 ACL
          protocol extension and you want your NFS client to allow
          applications to access and modify ACLs on files on the server.

          Most NFS servers don't support the Solaris NFSv3 ACL protocol
          extension.  You can choose N here or specify the "noacl" mount
          option to prevent your NFS client from trying to use the NFSv3
          ACL protocol.

          If unsure, say N.

config NFS_V4
        bool "NFS client support for NFS version 4 (EXPERIMENTAL)"
        depends on NFS_FS && EXPERIMENTAL
        select RPCSEC_GSS_KRB5
        help
          This option enables support for version 4 of the NFS protocol
          (RFC 3530) in the kernel's NFS client.

          To mount NFS servers using NFSv4, you also need to install user
          space programs which can be found in the Linux nfs-utils package,
          available from http://linux-nfs.org/.

          If unsure, say N.

config ROOT_NFS
        bool "Root file system on NFS"
        depends on NFS_FS=y && IP_PNP
        help
          If you want your system to mount its root file system via NFS,
          choose Y here.  This is common practice for managing systems
          without local permanent storage.  For details, read
          <file:Documentation/filesystems/nfsroot.txt>.

          Most people say N here.

config NFSD
        tristate "NFS server support"
        depends on INET
        select LOCKD
        select SUNRPC
        select EXPORTFS
        select NFS_ACL_SUPPORT if NFSD_V2_ACL
        help
          Choose Y here if you want to allow other computers to access
          files residing on this system using Sun's Network File System
          protocol.  To compile the NFS server support as a module,
          choose M here: the module will be called nfsd.

          You may choose to use a user-space NFS server instead, in which
          case you can choose N here.

          To export local file systems using NFS, you also need to install
          user space programs which can be found in the Linux nfs-utils
          package, available from http://linux-nfs.org/.  More detail about
          the Linux NFS server implementation is available via the
          exports(5) man page.

          Below you can choose which versions of the NFS protocol are
          available to clients mounting the NFS server on this system.
          Support for NFS version 2 (RFC 1094) is always available when
          CONFIG_NFSD is selected.

          If unsure, say N.

config NFSD_V2_ACL
        bool
        depends on NFSD

config NFSD_V3
        bool "NFS server support for NFS version 3"
        depends on NFSD
        help
          This option enables support in your system's NFS server for
          version 3 of the NFS protocol (RFC 1813).

          If unsure, say Y.

config NFSD_V3_ACL
        bool "NFS server support for the NFSv3 ACL protocol extension"
        depends on NFSD_V3
        select NFSD_V2_ACL
        help
          Solaris NFS servers support an auxiliary NFSv3 ACL protocol that
          never became an official part of the NFS version 3 protocol.
          This protocol extension allows applications on NFS clients to
          manipulate POSIX Access Control Lists on files residing on NFS
          servers.  NFS servers enforce POSIX ACLs on local files whether
          this protocol is available or not.

          This option enables support in your system's NFS server for the
          NFSv3 ACL protocol extension allowing NFS clients to manipulate
          POSIX ACLs on files exported by your system's NFS server.  NFS
          clients which support the Solaris NFSv3 ACL protocol can then
          access and modify ACLs on your NFS server.

          To store ACLs on your NFS server, you also need to enable ACL-
          related CONFIG options for your local file systems of choice.

          If unsure, say N.

config NFSD_V4
        bool "NFS server support for NFS version 4 (EXPERIMENTAL)"
        depends on NFSD && PROC_FS && EXPERIMENTAL
        select NFSD_V3
        select FS_POSIX_ACL
        select RPCSEC_GSS_KRB5
        help
          This option enables support in your system's NFS server for
          version 4 of the NFS protocol (RFC 3530).

          To export files using NFSv4, you need to install additional user
          space programs which can be found in the Linux nfs-utils package,
          available from http://linux-nfs.org/.

          If unsure, say N.

config LOCKD
        tristate

config LOCKD_V4
        bool
        depends on NFSD_V3 || NFS_V3
        default y

config EXPORTFS
        tristate

config NFS_ACL_SUPPORT
        tristate
        select FS_POSIX_ACL

config NFS_COMMON
        bool
        depends on NFSD || NFS_FS
        default y

config SUNRPC
        tristate

config SUNRPC_GSS
        tristate

config SUNRPC_XPRT_RDMA
        tristate
        depends on SUNRPC && INFINIBAND && EXPERIMENTAL
        default SUNRPC && INFINIBAND
        help
          This option enables an RPC client transport capability that
          allows the NFS client to mount servers via an RDMA-enabled
          transport.

          To compile RPC client RDMA transport support as a module,
          choose M here: the module will be called xprtrdma.

          If unsure, say N.

config SUNRPC_REGISTER_V4
        bool "Register local RPC services via rpcbind v4 (EXPERIMENTAL)"
        depends on SUNRPC && EXPERIMENTAL
        default n
        help
          Sun added support for registering RPC services at an IPv6
          address by creating two new versions of the rpcbind protocol
          (RFC 1833).

          This option enables support in the kernel RPC server for
          registering kernel RPC services via version 4 of the rpcbind
          protocol.  If you enable this option, you must run a portmapper
          daemon that supports rpcbind protocol version 4.

          Serving NFS over IPv6 from knfsd (the kernel's NFS server)
          requires that you enable this option and use a portmapper that
          supports rpcbind version 4.

          If unsure, say N to get traditional behavior (register kernel
          RPC services using only rpcbind version 2).  Distributions
          using the legacy Linux portmapper daemon must say N here.

config RPCSEC_GSS_KRB5
        tristate "Secure RPC: Kerberos V mechanism (EXPERIMENTAL)"
        depends on SUNRPC && EXPERIMENTAL
        select SUNRPC_GSS
        select CRYPTO
        select CRYPTO_MD5
        select CRYPTO_DES
        select CRYPTO_CBC
        help
          Choose Y here to enable Secure RPC using the Kerberos version 5
          GSS-API mechanism (RFC 1964).

          Secure RPC calls with Kerberos require an auxiliary user-space
          daemon which may be found in the Linux nfs-utils package
          available from http://linux-nfs.org/.  In addition, user-space
          Kerberos support should be installed.

          If unsure, say N.

config RPCSEC_GSS_SPKM3
        tristate "Secure RPC: SPKM3 mechanism (EXPERIMENTAL)"
        depends on SUNRPC && EXPERIMENTAL
        select SUNRPC_GSS
        select CRYPTO
        select CRYPTO_MD5
        select CRYPTO_DES
        select CRYPTO_CAST5
        select CRYPTO_CBC
        help
          Choose Y here to enable Secure RPC using the SPKM3 public key
          GSS-API mechansim (RFC 2025).

          Secure RPC calls with SPKM3 require an auxiliary userspace
          daemon which may be found in the Linux nfs-utils package
          available from http://linux-nfs.org/.

          If unsure, say N.

config SMB_FS
        tristate "SMB file system support (OBSOLETE, please use CIFS)"
        depends on INET
        select NLS
        help
          SMB (Server Message Block) is the protocol Windows for Workgroups
          (WfW), Windows 95/98, Windows NT and OS/2 Lan Manager use to share
          files and printers over local networks.  Saying Y here allows you to
          mount their file systems (often called "shares" in this context) and
          access them just like any other Unix directory.  Currently, this
          works only if the Windows machines use TCP/IP as the underlying
          transport protocol, and not NetBEUI.  For details, read
          <file:Documentation/filesystems/smbfs.txt> and the SMB-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>.

          Note: if you just want your box to act as an SMB *server* and make
          files and printing services available to Windows clients (which need
          to have a TCP/IP stack), you don't need to say Y here; you can use
          the program SAMBA (available from <ftp://ftp.samba.org/pub/samba/>)
          for that.

          General information about how to connect Linux, Windows machines and
          Macs is on the WWW at <http://www.eats.com/linux_mac_win.html>.

          To compile the SMB support as a module, choose M here:
          the module will be called smbfs.  Most people say N, however.

config SMB_NLS_DEFAULT
        bool "Use a default NLS"
        depends on SMB_FS
        help
          Enabling this will make smbfs use nls translations by default. You
          need to specify the local charset (CONFIG_NLS_DEFAULT) in the nls
          settings and you need to give the default nls for the SMB server as
          CONFIG_SMB_NLS_REMOTE.

          The nls settings can be changed at mount time, if your smbmount
          supports that, using the codepage and iocharset parameters.

          smbmount from samba 2.2.0 or later supports this.

config SMB_NLS_REMOTE
        string "Default Remote NLS Option"
        depends on SMB_NLS_DEFAULT
        default "cp437"
        help
          This setting allows you to specify a default value for which
          codepage the server uses. If this field is left blank no
          translations will be done by default. The local codepage/charset
          default to CONFIG_NLS_DEFAULT.

          The nls settings can be changed at mount time, if your smbmount
          supports that, using the codepage and iocharset parameters.

          smbmount from samba 2.2.0 or later supports this.

source "fs/cifs/Kconfig"

config NCP_FS
        tristate "NCP file system support (to mount NetWare volumes)"
        depends on IPX!=n || INET
        help
          NCP (NetWare Core Protocol) is a protocol that runs over IPX and is
          used by Novell NetWare clients to talk to file servers.  It is to
          IPX what NFS is to TCP/IP, if that helps.  Saying Y here allows you
          to mount NetWare file server volumes and to access them just like
          any other Unix directory.  For details, please read the file
          <file:Documentation/filesystems/ncpfs.txt> in the kernel source and
          the IPX-HOWTO from <http://www.tldp.org/docs.html#howto>.

          You do not have to say Y here if you want your Linux box to act as a
          file *server* for Novell NetWare clients.

          General information about how to connect Linux, Windows machines and
          Macs is on the WWW at <http://www.eats.com/linux_mac_win.html>.

          To compile this as a module, choose M here: the module will be called
          ncpfs.  Say N unless you are connected to a Novell network.

source "fs/ncpfs/Kconfig"

config CODA_FS
        tristate "Coda file system support (advanced network fs)"
        depends on INET
        help
          Coda is an advanced network file system, similar to NFS in that it
          enables you to mount file systems of a remote server and access them
          with regular Unix commands as if they were sitting on your hard
          disk.  Coda has several advantages over NFS: support for
          disconnected operation (e.g. for laptops), read/write server
          replication, security model for authentication and encryption,
          persistent client caches and write back caching.

          If you say Y here, your Linux box will be able to act as a Coda
          *client*.  You will need user level code as well, both for the
          client and server.  Servers are currently user level, i.e. they need
          no kernel support.  Please read
          <file:Documentation/filesystems/coda.txt> and check out the Coda
          home page <http://www.coda.cs.cmu.edu/>.

          To compile the coda client support as a module, choose M here: the
          module will be called coda.

config AFS_FS
        tristate "Andrew File System support (AFS) (EXPERIMENTAL)"
        depends on INET && EXPERIMENTAL
        select AF_RXRPC
        help
          If you say Y here, you will get an experimental Andrew File System
          driver. It currently only supports unsecured read-only AFS access.

          See <file:Documentation/filesystems/afs.txt> for more information.

          If unsure, say N.

config AFS_DEBUG
        bool "AFS dynamic debugging"
        depends on AFS_FS
        help
          Say Y here to make runtime controllable debugging messages appear.

          See <file:Documentation/filesystems/afs.txt> for more information.

          If unsure, say N.

config 9P_FS
        tristate "Plan 9 Resource Sharing Support (9P2000) (Experimental)"
        depends on INET && NET_9P && EXPERIMENTAL
        help
          If you say Y here, you will get experimental support for
          Plan 9 resource sharing via the 9P2000 protocol.

          See <http://v9fs.sf.net> for more information.

          If unsure, say N.

endif # NETWORK_FILESYSTEMS

if BLOCK
menu "Partition Types"

source "fs/partitions/Kconfig"

endmenu
endif

source "fs/nls/Kconfig"
source "fs/dlm/Kconfig"

endmenu