SAFE public projects git trees. - safe/jmp/linux-2.6/blob - drivers/ssb/driver_chipcommon.c

   1 /*
   2  * Sonics Silicon Backplane
   3  * Broadcom ChipCommon core driver
   4  *
   5  * Copyright 2005, Broadcom Corporation
   6  * Copyright 2006, 2007, Michael Buesch <mb@bu3sch.de>
   7  *
   8  * Licensed under the GNU/GPL. See COPYING for details.
   9  */
  10
  11 #include <linux/ssb/ssb.h>
  12 #include <linux/ssb/ssb_regs.h>
  13 #include <linux/pci.h>
  14
  15 #include "ssb_private.h"
  16
  17
  18 /* Clock sources */
  19 enum ssb_clksrc {
  20         /* PCI clock */
  21         SSB_CHIPCO_CLKSRC_PCI,
  22         /* Crystal slow clock oscillator */
  23         SSB_CHIPCO_CLKSRC_XTALOS,
  24         /* Low power oscillator */
  25         SSB_CHIPCO_CLKSRC_LOPWROS,
  26 };
  27
  28
  29 static inline u32 chipco_write32_masked(struct ssb_chipcommon *cc, u16 offset,
  30                                         u32 mask, u32 value)
  31 {
  32         value &= mask;
  33         value |= chipco_read32(cc, offset) & ~mask;
  34         chipco_write32(cc, offset, value);
  35
  36         return value;
  37 }
  38
  39 void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
  40                               enum ssb_clkmode mode)
  41 {
  42         struct ssb_device *ccdev = cc->dev;
  43         struct ssb_bus *bus;
  44         u32 tmp;
  45
  46         if (!ccdev)
  47                 return;
  48         bus = ccdev->bus;
  49         /* chipcommon cores prior to rev6 don't support dynamic clock control */
  50         if (ccdev->id.revision < 6)
  51                 return;
  52         /* chipcommon cores rev10 are a whole new ball game */
  53         if (ccdev->id.revision >= 10)
  54                 return;
  55         if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
  56                 return;
  57
  58         switch (mode) {
  59         case SSB_CLKMODE_SLOW:
  60                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
  61                 tmp |= SSB_CHIPCO_SLOWCLKCTL_FSLOW;
  62                 chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
  63                 break;
  64         case SSB_CLKMODE_FAST:
  65                 ssb_pci_xtal(bus, SSB_GPIO_XTAL, 1); /* Force crystal on */
  66                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
  67                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_FSLOW;
  68                 tmp |= SSB_CHIPCO_SLOWCLKCTL_IPLL;
  69                 chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
  70                 break;
  71         case SSB_CLKMODE_DYNAMIC:
  72                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
  73                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_FSLOW;
  74                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_IPLL;
  75                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_ENXTAL;
  76                 if ((tmp & SSB_CHIPCO_SLOWCLKCTL_SRC) != SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL)
  77                         tmp |= SSB_CHIPCO_SLOWCLKCTL_ENXTAL;
  78                 chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
  79
  80                 /* for dynamic control, we have to release our xtal_pu "force on" */
  81                 if (tmp & SSB_CHIPCO_SLOWCLKCTL_ENXTAL)
  82                         ssb_pci_xtal(bus, SSB_GPIO_XTAL, 0);
  83                 break;
  84         default:
  85                 SSB_WARN_ON(1);
  86         }
  87 }
  88
  89 /* Get the Slow Clock Source */
  90 static enum ssb_clksrc chipco_pctl_get_slowclksrc(struct ssb_chipcommon *cc)
  91 {
  92         struct ssb_bus *bus = cc->dev->bus;
  93         u32 uninitialized_var(tmp);
  94
  95         if (cc->dev->id.revision < 6) {
  96                 if (bus->bustype == SSB_BUSTYPE_SSB ||
  97                     bus->bustype == SSB_BUSTYPE_PCMCIA)
  98                         return SSB_CHIPCO_CLKSRC_XTALOS;
  99                 if (bus->bustype == SSB_BUSTYPE_PCI) {
 100                         pci_read_config_dword(bus->host_pci, SSB_GPIO_OUT, &tmp);
 101                         if (tmp & 0x10)
 102                                 return SSB_CHIPCO_CLKSRC_PCI;
 103                         return SSB_CHIPCO_CLKSRC_XTALOS;
 104                 }
 105         }
 106         if (cc->dev->id.revision < 10) {
 107                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
 108                 tmp &= 0x7;
 109                 if (tmp == 0)
 110                         return SSB_CHIPCO_CLKSRC_LOPWROS;
 111                 if (tmp == 1)
 112                         return SSB_CHIPCO_CLKSRC_XTALOS;
 113                 if (tmp == 2)
 114                         return SSB_CHIPCO_CLKSRC_PCI;
 115         }
 116
 117         return SSB_CHIPCO_CLKSRC_XTALOS;
 118 }
 119
 120 /* Get maximum or minimum (depending on get_max flag) slowclock frequency. */
 121 static int chipco_pctl_clockfreqlimit(struct ssb_chipcommon *cc, int get_max)
 122 {
 123         int uninitialized_var(limit);
 124         enum ssb_clksrc clocksrc;
 125         int divisor = 1;
 126         u32 tmp;
 127
 128         clocksrc = chipco_pctl_get_slowclksrc(cc);
 129         if (cc->dev->id.revision < 6) {
 130                 switch (clocksrc) {
 131                 case SSB_CHIPCO_CLKSRC_PCI:
 132                         divisor = 64;
 133                         break;
 134                 case SSB_CHIPCO_CLKSRC_XTALOS:
 135                         divisor = 32;
 136                         break;
 137                 default:
 138                         SSB_WARN_ON(1);
 139                 }
 140         } else if (cc->dev->id.revision < 10) {
 141                 switch (clocksrc) {
 142                 case SSB_CHIPCO_CLKSRC_LOPWROS:
 143                         break;
 144                 case SSB_CHIPCO_CLKSRC_XTALOS:
 145                 case SSB_CHIPCO_CLKSRC_PCI:
 146                         tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
 147                         divisor = (tmp >> 16) + 1;
 148                         divisor *= 4;
 149                         break;
 150                 }
 151         } else {
 152                 tmp = chipco_read32(cc, SSB_CHIPCO_SYSCLKCTL);
 153                 divisor = (tmp >> 16) + 1;
 154                 divisor *= 4;
 155         }
 156
 157         switch (clocksrc) {
 158         case SSB_CHIPCO_CLKSRC_LOPWROS:
 159                 if (get_max)
 160                         limit = 43000;
 161                 else
 162                         limit = 25000;
 163                 break;
 164         case SSB_CHIPCO_CLKSRC_XTALOS:
 165                 if (get_max)
 166                         limit = 20200000;
 167                 else
 168                         limit = 19800000;
 169                 break;
 170         case SSB_CHIPCO_CLKSRC_PCI:
 171                 if (get_max)
 172                         limit = 34000000;
 173                 else
 174                         limit = 25000000;
 175                 break;
 176         }
 177         limit /= divisor;
 178
 179         return limit;
 180 }
 181
 182 static void chipco_powercontrol_init(struct ssb_chipcommon *cc)
 183 {
 184         struct ssb_bus *bus = cc->dev->bus;
 185
 186         if (bus->chip_id == 0x4321) {
 187                 if (bus->chip_rev == 0)
 188                         chipco_write32(cc, SSB_CHIPCO_CHIPCTL, 0x3A4);
 189                 else if (bus->chip_rev == 1)
 190                         chipco_write32(cc, SSB_CHIPCO_CHIPCTL, 0xA4);
 191         }
 192
 193         if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
 194                 return;
 195
 196         if (cc->dev->id.revision >= 10) {
 197                 /* Set Idle Power clock rate to 1Mhz */
 198                 chipco_write32(cc, SSB_CHIPCO_SYSCLKCTL,
 199                                (chipco_read32(cc, SSB_CHIPCO_SYSCLKCTL) &
 200                                 0x0000FFFF) | 0x00040000);
 201         } else {
 202                 int maxfreq;
 203
 204                 maxfreq = chipco_pctl_clockfreqlimit(cc, 1);
 205                 chipco_write32(cc, SSB_CHIPCO_PLLONDELAY,
 206                                (maxfreq * 150 + 999999) / 1000000);
 207                 chipco_write32(cc, SSB_CHIPCO_FREFSELDELAY,
 208                                (maxfreq * 15 + 999999) / 1000000);
 209         }
 210 }
 211
 212 static void calc_fast_powerup_delay(struct ssb_chipcommon *cc)
 213 {
 214         struct ssb_bus *bus = cc->dev->bus;
 215         int minfreq;
 216         unsigned int tmp;
 217         u32 pll_on_delay;
 218
 219         if (bus->bustype != SSB_BUSTYPE_PCI)
 220                 return;
 221         if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
 222                 return;
 223
 224         minfreq = chipco_pctl_clockfreqlimit(cc, 0);
 225         pll_on_delay = chipco_read32(cc, SSB_CHIPCO_PLLONDELAY);
 226         tmp = (((pll_on_delay + 2) * 1000000) + (minfreq - 1)) / minfreq;
 227         SSB_WARN_ON(tmp & ~0xFFFF);
 228
 229         cc->fast_pwrup_delay = tmp;
 230 }
 231
 232 void ssb_chipcommon_init(struct ssb_chipcommon *cc)
 233 {
 234         if (!cc->dev)
 235                 return; /* We don't have a ChipCommon */
 236         if (cc->dev->id.revision >= 11)
 237                 cc->status = chipco_read32(cc, SSB_CHIPCO_CHIPSTAT);
 238         ssb_pmu_init(cc);
 239         chipco_powercontrol_init(cc);
 240         ssb_chipco_set_clockmode(cc, SSB_CLKMODE_FAST);
 241         calc_fast_powerup_delay(cc);
 242 }
 243
 244 void ssb_chipco_suspend(struct ssb_chipcommon *cc)
 245 {
 246         if (!cc->dev)
 247                 return;
 248         ssb_chipco_set_clockmode(cc, SSB_CLKMODE_SLOW);
 249 }
 250
 251 void ssb_chipco_resume(struct ssb_chipcommon *cc)
 252 {
 253         if (!cc->dev)
 254                 return;
 255         chipco_powercontrol_init(cc);
 256         ssb_chipco_set_clockmode(cc, SSB_CLKMODE_FAST);
 257 }
 258
 259 /* Get the processor clock */
 260 void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc,
 261                              u32 *plltype, u32 *n, u32 *m)
 262 {
 263         *n = chipco_read32(cc, SSB_CHIPCO_CLOCK_N);
 264         *plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
 265         switch (*plltype) {
 266         case SSB_PLLTYPE_2:
 267         case SSB_PLLTYPE_4:
 268         case SSB_PLLTYPE_6:
 269         case SSB_PLLTYPE_7:
 270                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_MIPS);
 271                 break;
 272         case SSB_PLLTYPE_3:
 273                 /* 5350 uses m2 to control mips */
 274                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_M2);
 275                 break;
 276         default:
 277                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_SB);
 278                 break;
 279         }
 280 }
 281
 282 /* Get the bus clock */
 283 void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
 284                                  u32 *plltype, u32 *n, u32 *m)
 285 {
 286         *n = chipco_read32(cc, SSB_CHIPCO_CLOCK_N);
 287         *plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
 288         switch (*plltype) {
 289         case SSB_PLLTYPE_6: /* 100/200 or 120/240 only */
 290                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_MIPS);
 291                 break;
 292         case SSB_PLLTYPE_3: /* 25Mhz, 2 dividers */
 293                 if (cc->dev->bus->chip_id != 0x5365) {
 294                         *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_M2);
 295                         break;
 296                 }
 297                 /* Fallthough */
 298         default:
 299                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_SB);
 300         }
 301 }
 302
 303 void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
 304                             unsigned long ns)
 305 {
 306         struct ssb_device *dev = cc->dev;
 307         struct ssb_bus *bus = dev->bus;
 308         u32 tmp;
 309
 310         /* set register for external IO to control LED. */
 311         chipco_write32(cc, SSB_CHIPCO_PROG_CFG, 0x11);
 312         tmp = DIV_ROUND_UP(10, ns) << SSB_PROG_WCNT_3_SHIFT;            /* Waitcount-3 = 10ns */
 313         tmp |= DIV_ROUND_UP(40, ns) << SSB_PROG_WCNT_1_SHIFT;   /* Waitcount-1 = 40ns */
 314         tmp |= DIV_ROUND_UP(240, ns);                           /* Waitcount-0 = 240ns */
 315         chipco_write32(cc, SSB_CHIPCO_PROG_WAITCNT, tmp);       /* 0x01020a0c for a 100Mhz clock */
 316
 317         /* Set timing for the flash */
 318         tmp = DIV_ROUND_UP(10, ns) << SSB_FLASH_WCNT_3_SHIFT;   /* Waitcount-3 = 10nS */
 319         tmp |= DIV_ROUND_UP(10, ns) << SSB_FLASH_WCNT_1_SHIFT;  /* Waitcount-1 = 10nS */
 320         tmp |= DIV_ROUND_UP(120, ns);                           /* Waitcount-0 = 120nS */
 321         if ((bus->chip_id == 0x5365) ||
 322             (dev->id.revision < 9))
 323                 chipco_write32(cc, SSB_CHIPCO_FLASH_WAITCNT, tmp);
 324         if ((bus->chip_id == 0x5365) ||
 325             (dev->id.revision < 9) ||
 326             ((bus->chip_id == 0x5350) && (bus->chip_rev == 0)))
 327                 chipco_write32(cc, SSB_CHIPCO_PCMCIA_MEMWAIT, tmp);
 328
 329         if (bus->chip_id == 0x5350) {
 330                 /* Enable EXTIF */
 331                 tmp = DIV_ROUND_UP(10, ns) << SSB_PROG_WCNT_3_SHIFT;      /* Waitcount-3 = 10ns */
 332                 tmp |= DIV_ROUND_UP(20, ns) << SSB_PROG_WCNT_2_SHIFT;  /* Waitcount-2 = 20ns */
 333                 tmp |= DIV_ROUND_UP(100, ns) << SSB_PROG_WCNT_1_SHIFT; /* Waitcount-1 = 100ns */
 334                 tmp |= DIV_ROUND_UP(120, ns);                     /* Waitcount-0 = 120ns */
 335                 chipco_write32(cc, SSB_CHIPCO_PROG_WAITCNT, tmp); /* 0x01020a0c for a 100Mhz clock */
 336         }
 337 }
 338
 339 /* Set chip watchdog reset timer to fire in 'ticks' backplane cycles */
 340 void ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks)
 341 {
 342         /* instant NMI */
 343         chipco_write32(cc, SSB_CHIPCO_WATCHDOG, ticks);
 344 }
 345
 346 void ssb_chipco_irq_mask(struct ssb_chipcommon *cc, u32 mask, u32 value)
 347 {
 348         chipco_write32_masked(cc, SSB_CHIPCO_IRQMASK, mask, value);
 349 }
 350
 351 u32 ssb_chipco_irq_status(struct ssb_chipcommon *cc, u32 mask)
 352 {
 353         return chipco_read32(cc, SSB_CHIPCO_IRQSTAT) & mask;
 354 }
 355
 356 u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask)
 357 {
 358         return chipco_read32(cc, SSB_CHIPCO_GPIOIN) & mask;
 359 }
 360
 361 u32 ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value)
 362 {
 363         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOOUT, mask, value);
 364 }
 365
 366 u32 ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value)
 367 {
 368         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOOUTEN, mask, value);
 369 }
 370
 371 u32 ssb_chipco_gpio_control(struct ssb_chipcommon *cc, u32 mask, u32 value)
 372 {
 373         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOCTL, mask, value);
 374 }
 375 EXPORT_SYMBOL(ssb_chipco_gpio_control);
 376
 377 u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value)
 378 {
 379         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOIRQ, mask, value);
 380 }
 381
 382 u32 ssb_chipco_gpio_polarity(struct ssb_chipcommon *cc, u32 mask, u32 value)
 383 {
 384         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOPOL, mask, value);
 385 }
 386
 387 #ifdef CONFIG_SSB_SERIAL
 388 int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
 389                            struct ssb_serial_port *ports)
 390 {
 391         struct ssb_bus *bus = cc->dev->bus;
 392         int nr_ports = 0;
 393         u32 plltype;
 394         unsigned int irq;
 395         u32 baud_base, div;
 396         u32 i, n;
 397         unsigned int ccrev = cc->dev->id.revision;
 398
 399         plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
 400         irq = ssb_mips_irq(cc->dev);
 401
 402         if (plltype == SSB_PLLTYPE_1) {
 403                 /* PLL clock */
 404                 baud_base = ssb_calc_clock_rate(plltype,
 405                                                 chipco_read32(cc, SSB_CHIPCO_CLOCK_N),
 406                                                 chipco_read32(cc, SSB_CHIPCO_CLOCK_M2));
 407                 div = 1;
 408         } else {
 409                 if (ccrev == 20) {
 410                         /* BCM5354 uses constant 25MHz clock */
 411                         baud_base = 25000000;
 412                         div = 48;
 413                         /* Set the override bit so we don't divide it */
 414                         chipco_write32(cc, SSB_CHIPCO_CORECTL,
 415                                        chipco_read32(cc, SSB_CHIPCO_CORECTL)
 416                                        | SSB_CHIPCO_CORECTL_UARTCLK0);
 417                 } else if ((ccrev >= 11) && (ccrev != 15)) {
 418                         /* Fixed ALP clock */
 419                         baud_base = 20000000;
 420                         if (cc->capabilities & SSB_CHIPCO_CAP_PMU) {
 421                                 /* FIXME: baud_base is different for devices with a PMU */
 422                                 SSB_WARN_ON(1);
 423                         }
 424                         div = 1;
 425                         if (ccrev >= 21) {
 426                                 /* Turn off UART clock before switching clocksource. */
 427                                 chipco_write32(cc, SSB_CHIPCO_CORECTL,
 428                                                chipco_read32(cc, SSB_CHIPCO_CORECTL)
 429                                                & ~SSB_CHIPCO_CORECTL_UARTCLKEN);
 430                         }
 431                         /* Set the override bit so we don't divide it */
 432                         chipco_write32(cc, SSB_CHIPCO_CORECTL,
 433                                        chipco_read32(cc, SSB_CHIPCO_CORECTL)
 434                                        | SSB_CHIPCO_CORECTL_UARTCLK0);
 435                         if (ccrev >= 21) {
 436                                 /* Re-enable the UART clock. */
 437                                 chipco_write32(cc, SSB_CHIPCO_CORECTL,
 438                                                chipco_read32(cc, SSB_CHIPCO_CORECTL)
 439                                                | SSB_CHIPCO_CORECTL_UARTCLKEN);
 440                         }
 441                 } else if (ccrev >= 3) {
 442                         /* Internal backplane clock */
 443                         baud_base = ssb_clockspeed(bus);
 444                         div = chipco_read32(cc, SSB_CHIPCO_CLKDIV)
 445                               & SSB_CHIPCO_CLKDIV_UART;
 446                 } else {
 447                         /* Fixed internal backplane clock */
 448                         baud_base = 88000000;
 449                         div = 48;
 450                 }
 451
 452                 /* Clock source depends on strapping if UartClkOverride is unset */
 453                 if ((ccrev > 0) &&
 454                     !(chipco_read32(cc, SSB_CHIPCO_CORECTL) & SSB_CHIPCO_CORECTL_UARTCLK0)) {
 455                         if ((cc->capabilities & SSB_CHIPCO_CAP_UARTCLK) ==
 456                             SSB_CHIPCO_CAP_UARTCLK_INT) {
 457                                 /* Internal divided backplane clock */
 458                                 baud_base /= div;
 459                         } else {
 460                                 /* Assume external clock of 1.8432 MHz */
 461                                 baud_base = 1843200;
 462                         }
 463                 }
 464         }
 465
 466         /* Determine the registers of the UARTs */
 467         n = (cc->capabilities & SSB_CHIPCO_CAP_NRUART);
 468         for (i = 0; i < n; i++) {
 469                 void __iomem *cc_mmio;
 470                 void __iomem *uart_regs;
 471
 472                 cc_mmio = cc->dev->bus->mmio + (cc->dev->core_index * SSB_CORE_SIZE);
 473                 uart_regs = cc_mmio + SSB_CHIPCO_UART0_DATA;
 474                 /* Offset changed at after rev 0 */
 475                 if (ccrev == 0)
 476                         uart_regs += (i * 8);
 477                 else
 478                         uart_regs += (i * 256);
 479
 480                 nr_ports++;
 481                 ports[i].regs = uart_regs;
 482                 ports[i].irq = irq;
 483                 ports[i].baud_base = baud_base;
 484                 ports[i].reg_shift = 0;
 485         }
 486
 487         return nr_ports;
 488 }
 489 #endif /* CONFIG_SSB_SERIAL */