SAFE public projects git trees. - safe/jmp/linux-2.6/blob - drivers/serial/bfin_5xx.c

   1 /*
   2  * Blackfin On-Chip Serial Driver
   3  *
   4  * Copyright 2006-2008 Analog Devices Inc.
   5  *
   6  * Enter bugs at http://blackfin.uclinux.org/
   7  *
   8  * Licensed under the GPL-2 or later.
   9  */
  10
  11 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  12 #define SUPPORT_SYSRQ
  13 #endif
  14
  15 #include <linux/module.h>
  16 #include <linux/ioport.h>
  17 #include <linux/init.h>
  18 #include <linux/console.h>
  19 #include <linux/sysrq.h>
  20 #include <linux/platform_device.h>
  21 #include <linux/tty.h>
  22 #include <linux/tty_flip.h>
  23 #include <linux/serial_core.h>
  24
  25 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
  26         defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
  27 #include <linux/kgdb.h>
  28 #include <asm/irq_regs.h>
  29 #endif
  30
  31 #include <asm/gpio.h>
  32 #include <mach/bfin_serial_5xx.h>
  33
  34 #ifdef CONFIG_SERIAL_BFIN_DMA
  35 #include <linux/dma-mapping.h>
  36 #include <asm/io.h>
  37 #include <asm/irq.h>
  38 #include <asm/cacheflush.h>
  39 #endif
  40
  41 #ifdef CONFIG_SERIAL_BFIN_MODULE
  42 # undef CONFIG_EARLY_PRINTK
  43 #endif
  44
  45 /* UART name and device definitions */
  46 #define BFIN_SERIAL_NAME        "ttyBF"
  47 #define BFIN_SERIAL_MAJOR       204
  48 #define BFIN_SERIAL_MINOR       64
  49
  50 static struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
  51 static int nr_active_ports = ARRAY_SIZE(bfin_serial_resource);
  52
  53 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
  54         defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
  55
  56 # ifndef CONFIG_SERIAL_BFIN_PIO
  57 #  error KGDB only support UART in PIO mode.
  58 # endif
  59
  60 static int kgdboc_port_line;
  61 static int kgdboc_break_enabled;
  62 #endif
  63 /*
  64  * Setup for console. Argument comes from the menuconfig
  65  */
  66 #define DMA_RX_XCOUNT           512
  67 #define DMA_RX_YCOUNT           (PAGE_SIZE / DMA_RX_XCOUNT)
  68
  69 #define DMA_RX_FLUSH_JIFFIES    (HZ / 50)
  70
  71 #ifdef CONFIG_SERIAL_BFIN_DMA
  72 static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
  73 #else
  74 static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
  75 #endif
  76
  77 static void bfin_serial_reset_irda(struct uart_port *port);
  78
  79 #if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
  80         defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
  81 static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
  82 {
  83         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
  84         if (uart->cts_pin < 0)
  85                 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
  86
  87         /* CTS PIN is negative assertive. */
  88         if (UART_GET_CTS(uart))
  89                 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
  90         else
  91                 return TIOCM_DSR | TIOCM_CAR;
  92 }
  93
  94 static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
  95 {
  96         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
  97         if (uart->rts_pin < 0)
  98                 return;
  99
 100         /* RTS PIN is negative assertive. */
 101         if (mctrl & TIOCM_RTS)
 102                 UART_ENABLE_RTS(uart);
 103         else
 104                 UART_DISABLE_RTS(uart);
 105 }
 106
 107 /*
 108  * Handle any change of modem status signal.
 109  */
 110 static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
 111 {
 112         struct bfin_serial_port *uart = dev_id;
 113         unsigned int status;
 114
 115         status = bfin_serial_get_mctrl(&uart->port);
 116         uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
 117 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
 118         uart->scts = 1;
 119         UART_CLEAR_SCTS(uart);
 120         UART_CLEAR_IER(uart, EDSSI);
 121 #endif
 122
 123         return IRQ_HANDLED;
 124 }
 125 #else
 126 static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
 127 {
 128         return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
 129 }
 130
 131 static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
 132 {
 133 }
 134 #endif
 135
 136 /*
 137  * interrupts are disabled on entry
 138  */
 139 static void bfin_serial_stop_tx(struct uart_port *port)
 140 {
 141         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 142 #ifdef CONFIG_SERIAL_BFIN_DMA
 143         struct circ_buf *xmit = &uart->port.info->xmit;
 144 #endif
 145
 146         while (!(UART_GET_LSR(uart) & TEMT))
 147                 cpu_relax();
 148
 149 #ifdef CONFIG_SERIAL_BFIN_DMA
 150         disable_dma(uart->tx_dma_channel);
 151         xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
 152         uart->port.icount.tx += uart->tx_count;
 153         uart->tx_count = 0;
 154         uart->tx_done = 1;
 155 #else
 156 #ifdef CONFIG_BF54x
 157         /* Clear TFI bit */
 158         UART_PUT_LSR(uart, TFI);
 159 #endif
 160         UART_CLEAR_IER(uart, ETBEI);
 161 #endif
 162 }
 163
 164 /*
 165  * port is locked and interrupts are disabled
 166  */
 167 static void bfin_serial_start_tx(struct uart_port *port)
 168 {
 169         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 170         struct tty_struct *tty = uart->port.info->port.tty;
 171
 172 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
 173         if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
 174                 uart->scts = 0;
 175                 uart_handle_cts_change(&uart->port, uart->scts);
 176         }
 177 #endif
 178
 179         /*
 180          * To avoid losting RX interrupt, we reset IR function
 181          * before sending data.
 182          */
 183         if (tty->termios->c_line == N_IRDA)
 184                 bfin_serial_reset_irda(port);
 185
 186 #ifdef CONFIG_SERIAL_BFIN_DMA
 187         if (uart->tx_done)
 188                 bfin_serial_dma_tx_chars(uart);
 189 #else
 190         UART_SET_IER(uart, ETBEI);
 191         bfin_serial_tx_chars(uart);
 192 #endif
 193 }
 194
 195 /*
 196  * Interrupts are enabled
 197  */
 198 static void bfin_serial_stop_rx(struct uart_port *port)
 199 {
 200         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 201
 202         UART_CLEAR_IER(uart, ERBFI);
 203 }
 204
 205 /*
 206  * Set the modem control timer to fire immediately.
 207  */
 208 static void bfin_serial_enable_ms(struct uart_port *port)
 209 {
 210 }
 211
 212
 213 #if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
 214 # define UART_GET_ANOMALY_THRESHOLD(uart)    ((uart)->anomaly_threshold)
 215 # define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
 216 #else
 217 # define UART_GET_ANOMALY_THRESHOLD(uart)    0
 218 # define UART_SET_ANOMALY_THRESHOLD(uart, v)
 219 #endif
 220
 221 #ifdef CONFIG_SERIAL_BFIN_PIO
 222 static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
 223 {
 224         struct tty_struct *tty = NULL;
 225         unsigned int status, ch, flg;
 226         static struct timeval anomaly_start = { .tv_sec = 0 };
 227
 228         status = UART_GET_LSR(uart);
 229         UART_CLEAR_LSR(uart);
 230
 231         ch = UART_GET_CHAR(uart);
 232         uart->port.icount.rx++;
 233
 234 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
 235         defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
 236         if (kgdb_connected && kgdboc_port_line == uart->port.line)
 237                 if (ch == 0x3) {/* Ctrl + C */
 238                         kgdb_breakpoint();
 239                         return;
 240                 }
 241
 242         if (!uart->port.info || !uart->port.info->port.tty)
 243                 return;
 244 #endif
 245         tty = uart->port.info->port.tty;
 246
 247         if (ANOMALY_05000363) {
 248                 /* The BF533 (and BF561) family of processors have a nice anomaly
 249                  * where they continuously generate characters for a "single" break.
 250                  * We have to basically ignore this flood until the "next" valid
 251                  * character comes across.  Due to the nature of the flood, it is
 252                  * not possible to reliably catch bytes that are sent too quickly
 253                  * after this break.  So application code talking to the Blackfin
 254                  * which sends a break signal must allow at least 1.5 character
 255                  * times after the end of the break for things to stabilize.  This
 256                  * timeout was picked as it must absolutely be larger than 1
 257                  * character time +/- some percent.  So 1.5 sounds good.  All other
 258                  * Blackfin families operate properly.  Woo.
 259                  */
 260                 if (anomaly_start.tv_sec) {
 261                         struct timeval curr;
 262                         suseconds_t usecs;
 263
 264                         if ((~ch & (~ch + 1)) & 0xff)
 265                                 goto known_good_char;
 266
 267                         do_gettimeofday(&curr);
 268                         if (curr.tv_sec - anomaly_start.tv_sec > 1)
 269                                 goto known_good_char;
 270
 271                         usecs = 0;
 272                         if (curr.tv_sec != anomaly_start.tv_sec)
 273                                 usecs += USEC_PER_SEC;
 274                         usecs += curr.tv_usec - anomaly_start.tv_usec;
 275
 276                         if (usecs > UART_GET_ANOMALY_THRESHOLD(uart))
 277                                 goto known_good_char;
 278
 279                         if (ch)
 280                                 anomaly_start.tv_sec = 0;
 281                         else
 282                                 anomaly_start = curr;
 283
 284                         return;
 285
 286  known_good_char:
 287                         status &= ~BI;
 288                         anomaly_start.tv_sec = 0;
 289                 }
 290         }
 291
 292         if (status & BI) {
 293                 if (ANOMALY_05000363)
 294                         if (bfin_revid() < 5)
 295                                 do_gettimeofday(&anomaly_start);
 296                 uart->port.icount.brk++;
 297                 if (uart_handle_break(&uart->port))
 298                         goto ignore_char;
 299                 status &= ~(PE | FE);
 300         }
 301         if (status & PE)
 302                 uart->port.icount.parity++;
 303         if (status & OE)
 304                 uart->port.icount.overrun++;
 305         if (status & FE)
 306                 uart->port.icount.frame++;
 307
 308         status &= uart->port.read_status_mask;
 309
 310         if (status & BI)
 311                 flg = TTY_BREAK;
 312         else if (status & PE)
 313                 flg = TTY_PARITY;
 314         else if (status & FE)
 315                 flg = TTY_FRAME;
 316         else
 317                 flg = TTY_NORMAL;
 318
 319         if (uart_handle_sysrq_char(&uart->port, ch))
 320                 goto ignore_char;
 321
 322         uart_insert_char(&uart->port, status, OE, ch, flg);
 323
 324  ignore_char:
 325         tty_flip_buffer_push(tty);
 326 }
 327
 328 static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
 329 {
 330         struct circ_buf *xmit = &uart->port.info->xmit;
 331
 332         if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
 333 #ifdef CONFIG_BF54x
 334                 /* Clear TFI bit */
 335                 UART_PUT_LSR(uart, TFI);
 336 #endif
 337                 /* Anomaly notes:
 338                  *  05000215 -  we always clear ETBEI within last UART TX
 339                  *              interrupt to end a string. It is always set
 340                  *              when start a new tx.
 341                  */
 342                 UART_CLEAR_IER(uart, ETBEI);
 343                 return;
 344         }
 345
 346         if (uart->port.x_char) {
 347                 UART_PUT_CHAR(uart, uart->port.x_char);
 348                 uart->port.icount.tx++;
 349                 uart->port.x_char = 0;
 350         }
 351
 352         while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) {
 353                 UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
 354                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 355                 uart->port.icount.tx++;
 356                 SSYNC();
 357         }
 358
 359         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 360                 uart_write_wakeup(&uart->port);
 361 }
 362
 363 static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
 364 {
 365         struct bfin_serial_port *uart = dev_id;
 366
 367         spin_lock(&uart->port.lock);
 368         while (UART_GET_LSR(uart) & DR)
 369                 bfin_serial_rx_chars(uart);
 370         spin_unlock(&uart->port.lock);
 371
 372         return IRQ_HANDLED;
 373 }
 374
 375 static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
 376 {
 377         struct bfin_serial_port *uart = dev_id;
 378
 379 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
 380         if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
 381                 uart->scts = 0;
 382                 uart_handle_cts_change(&uart->port, uart->scts);
 383         }
 384 #endif
 385         spin_lock(&uart->port.lock);
 386         if (UART_GET_LSR(uart) & THRE)
 387                 bfin_serial_tx_chars(uart);
 388         spin_unlock(&uart->port.lock);
 389
 390         return IRQ_HANDLED;
 391 }
 392 #endif
 393
 394 #ifdef CONFIG_SERIAL_BFIN_DMA
 395 static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
 396 {
 397         struct circ_buf *xmit = &uart->port.info->xmit;
 398
 399         uart->tx_done = 0;
 400
 401         if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
 402                 uart->tx_count = 0;
 403                 uart->tx_done = 1;
 404                 return;
 405         }
 406
 407         if (uart->port.x_char) {
 408                 UART_PUT_CHAR(uart, uart->port.x_char);
 409                 uart->port.icount.tx++;
 410                 uart->port.x_char = 0;
 411         }
 412
 413         uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
 414         if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
 415                 uart->tx_count = UART_XMIT_SIZE - xmit->tail;
 416         blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
 417                                         (unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
 418         set_dma_config(uart->tx_dma_channel,
 419                 set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
 420                         INTR_ON_BUF,
 421                         DIMENSION_LINEAR,
 422                         DATA_SIZE_8,
 423                         DMA_SYNC_RESTART));
 424         set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
 425         set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
 426         set_dma_x_modify(uart->tx_dma_channel, 1);
 427         SSYNC();
 428         enable_dma(uart->tx_dma_channel);
 429
 430         UART_SET_IER(uart, ETBEI);
 431 }
 432
 433 static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
 434 {
 435         struct tty_struct *tty = uart->port.info->port.tty;
 436         int i, flg, status;
 437
 438         status = UART_GET_LSR(uart);
 439         UART_CLEAR_LSR(uart);
 440
 441         uart->port.icount.rx +=
 442                 CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail,
 443                 UART_XMIT_SIZE);
 444
 445         if (status & BI) {
 446                 uart->port.icount.brk++;
 447                 if (uart_handle_break(&uart->port))
 448                         goto dma_ignore_char;
 449                 status &= ~(PE | FE);
 450         }
 451         if (status & PE)
 452                 uart->port.icount.parity++;
 453         if (status & OE)
 454                 uart->port.icount.overrun++;
 455         if (status & FE)
 456                 uart->port.icount.frame++;
 457
 458         status &= uart->port.read_status_mask;
 459
 460         if (status & BI)
 461                 flg = TTY_BREAK;
 462         else if (status & PE)
 463                 flg = TTY_PARITY;
 464         else if (status & FE)
 465                 flg = TTY_FRAME;
 466         else
 467                 flg = TTY_NORMAL;
 468
 469         for (i = uart->rx_dma_buf.tail; ; i++) {
 470                 if (i >= UART_XMIT_SIZE)
 471                         i = 0;
 472                 if (i == uart->rx_dma_buf.head)
 473                         break;
 474                 if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
 475                         uart_insert_char(&uart->port, status, OE,
 476                                 uart->rx_dma_buf.buf[i], flg);
 477         }
 478
 479  dma_ignore_char:
 480         tty_flip_buffer_push(tty);
 481 }
 482
 483 void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 484 {
 485         int x_pos, pos;
 486
 487         dma_disable_irq(uart->rx_dma_channel);
 488         spin_lock_bh(&uart->port.lock);
 489
 490         /* 2D DMA RX buffer ring is used. Because curr_y_count and
 491          * curr_x_count can't be read as an atomic operation,
 492          * curr_y_count should be read before curr_x_count. When
 493          * curr_x_count is read, curr_y_count may already indicate
 494          * next buffer line. But, the position calculated here is
 495          * still indicate the old line. The wrong position data may
 496          * be smaller than current buffer tail, which cause garbages
 497          * are received if it is not prohibit.
 498          */
 499         uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
 500         x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
 501         uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
 502         if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
 503                 uart->rx_dma_nrows = 0;
 504         x_pos = DMA_RX_XCOUNT - x_pos;
 505         if (x_pos == DMA_RX_XCOUNT)
 506                 x_pos = 0;
 507
 508         pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
 509         /* Ignore receiving data if new position is in the same line of
 510          * current buffer tail and small.
 511          */
 512         if (pos > uart->rx_dma_buf.tail ||
 513                 uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
 514                 uart->rx_dma_buf.head = pos;
 515                 bfin_serial_dma_rx_chars(uart);
 516                 uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
 517         }
 518
 519         spin_unlock_bh(&uart->port.lock);
 520         dma_enable_irq(uart->rx_dma_channel);
 521
 522         mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
 523 }
 524
 525 static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
 526 {
 527         struct bfin_serial_port *uart = dev_id;
 528         struct circ_buf *xmit = &uart->port.info->xmit;
 529
 530 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
 531         if (uart->scts && !(bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
 532                 uart->scts = 0;
 533                 uart_handle_cts_change(&uart->port, uart->scts);
 534         }
 535 #endif
 536
 537         spin_lock(&uart->port.lock);
 538         if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
 539                 disable_dma(uart->tx_dma_channel);
 540                 clear_dma_irqstat(uart->tx_dma_channel);
 541                 /* Anomaly notes:
 542                  *  05000215 -  we always clear ETBEI within last UART TX
 543                  *              interrupt to end a string. It is always set
 544                  *              when start a new tx.
 545                  */
 546                 UART_CLEAR_IER(uart, ETBEI);
 547                 xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
 548                 uart->port.icount.tx += uart->tx_count;
 549
 550                 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 551                         uart_write_wakeup(&uart->port);
 552
 553                 bfin_serial_dma_tx_chars(uart);
 554         }
 555
 556         spin_unlock(&uart->port.lock);
 557         return IRQ_HANDLED;
 558 }
 559
 560 static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
 561 {
 562         struct bfin_serial_port *uart = dev_id;
 563         unsigned short irqstat;
 564         int x_pos, pos;
 565
 566         spin_lock(&uart->port.lock);
 567         irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
 568         clear_dma_irqstat(uart->rx_dma_channel);
 569
 570         uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
 571         x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
 572         uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
 573         if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
 574                 uart->rx_dma_nrows = 0;
 575
 576         pos = uart->rx_dma_nrows * DMA_RX_XCOUNT;
 577         if (pos > uart->rx_dma_buf.tail ||
 578                 uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
 579                 uart->rx_dma_buf.head = pos;
 580                 bfin_serial_dma_rx_chars(uart);
 581                 uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
 582         }
 583
 584         spin_unlock(&uart->port.lock);
 585
 586         return IRQ_HANDLED;
 587 }
 588 #endif
 589
 590 /*
 591  * Return TIOCSER_TEMT when transmitter is not busy.
 592  */
 593 static unsigned int bfin_serial_tx_empty(struct uart_port *port)
 594 {
 595         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 596         unsigned short lsr;
 597
 598         lsr = UART_GET_LSR(uart);
 599         if (lsr & TEMT)
 600                 return TIOCSER_TEMT;
 601         else
 602                 return 0;
 603 }
 604
 605 static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
 606 {
 607         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 608         u16 lcr = UART_GET_LCR(uart);
 609         if (break_state)
 610                 lcr |= SB;
 611         else
 612                 lcr &= ~SB;
 613         UART_PUT_LCR(uart, lcr);
 614         SSYNC();
 615 }
 616
 617 static int bfin_serial_startup(struct uart_port *port)
 618 {
 619         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 620
 621 #ifdef CONFIG_SERIAL_BFIN_DMA
 622         dma_addr_t dma_handle;
 623
 624         if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
 625                 printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
 626                 return -EBUSY;
 627         }
 628
 629         if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
 630                 printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
 631                 free_dma(uart->rx_dma_channel);
 632                 return -EBUSY;
 633         }
 634
 635         set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
 636         set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
 637
 638         uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
 639         uart->rx_dma_buf.head = 0;
 640         uart->rx_dma_buf.tail = 0;
 641         uart->rx_dma_nrows = 0;
 642
 643         set_dma_config(uart->rx_dma_channel,
 644                 set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
 645                                 INTR_ON_ROW, DIMENSION_2D,
 646                                 DATA_SIZE_8,
 647                                 DMA_SYNC_RESTART));
 648         set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
 649         set_dma_x_modify(uart->rx_dma_channel, 1);
 650         set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
 651         set_dma_y_modify(uart->rx_dma_channel, 1);
 652         set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
 653         enable_dma(uart->rx_dma_channel);
 654
 655         uart->rx_dma_timer.data = (unsigned long)(uart);
 656         uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
 657         uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
 658         add_timer(&(uart->rx_dma_timer));
 659 #else
 660 # if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
 661         defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
 662         if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
 663                 kgdboc_break_enabled = 0;
 664         else {
 665 # endif
 666         if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
 667              "BFIN_UART_RX", uart)) {
 668                 printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
 669                 return -EBUSY;
 670         }
 671
 672         if (request_irq
 673             (uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
 674              "BFIN_UART_TX", uart)) {
 675                 printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
 676                 free_irq(uart->port.irq, uart);
 677                 return -EBUSY;
 678         }
 679
 680 # ifdef CONFIG_BF54x
 681         {
 682                 unsigned uart_dma_ch_rx, uart_dma_ch_tx;
 683
 684                 switch (uart->port.irq) {
 685                 case IRQ_UART3_RX:
 686                         uart_dma_ch_rx = CH_UART3_RX;
 687                         uart_dma_ch_tx = CH_UART3_TX;
 688                         break;
 689                 case IRQ_UART2_RX:
 690                         uart_dma_ch_rx = CH_UART2_RX;
 691                         uart_dma_ch_tx = CH_UART2_TX;
 692                         break;
 693                 default:
 694                         uart_dma_ch_rx = uart_dma_ch_tx = 0;
 695                         break;
 696                 };
 697
 698                 if (uart_dma_ch_rx &&
 699                         request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
 700                         printk(KERN_NOTICE"Fail to attach UART interrupt\n");
 701                         free_irq(uart->port.irq, uart);
 702                         free_irq(uart->port.irq + 1, uart);
 703                         return -EBUSY;
 704                 }
 705                 if (uart_dma_ch_tx &&
 706                         request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
 707                         printk(KERN_NOTICE "Fail to attach UART interrupt\n");
 708                         free_dma(uart_dma_ch_rx);
 709                         free_irq(uart->port.irq, uart);
 710                         free_irq(uart->port.irq + 1, uart);
 711                         return -EBUSY;
 712                 }
 713         }
 714 # endif
 715 # if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
 716         defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
 717         }
 718 # endif
 719 #endif
 720
 721 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
 722         if (uart->cts_pin >= 0) {
 723                 if (request_irq(gpio_to_irq(uart->cts_pin),
 724                         bfin_serial_mctrl_cts_int,
 725                         IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
 726                         IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
 727                         uart->cts_pin = -1;
 728                         pr_info("Unable to attach BlackFin UART CTS interrupt.\
 729                                  So, disable it.\n");
 730                 }
 731         }
 732         if (uart->rts_pin >= 0) {
 733                 gpio_request(uart->rts_pin, DRIVER_NAME);
 734                 gpio_direction_output(uart->rts_pin, 0);
 735         }
 736 #endif
 737 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
 738         if (request_irq(uart->status_irq,
 739                 bfin_serial_mctrl_cts_int,
 740                 IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
 741                 pr_info("Unable to attach BlackFin UART Modem \
 742                         Status interrupt.\n");
 743         }
 744
 745         if (uart->cts_pin >= 0) {
 746                 gpio_request(uart->cts_pin, DRIVER_NAME);
 747                 gpio_direction_output(uart->cts_pin, 1);
 748         }
 749         if (uart->rts_pin >= 0) {
 750                 gpio_request(uart->rts_pin, DRIVER_NAME);
 751                 gpio_direction_output(uart->rts_pin, 0);
 752         }
 753
 754         /* CTS RTS PINs are negative assertive. */
 755         UART_PUT_MCR(uart, ACTS);
 756         UART_SET_IER(uart, EDSSI);
 757 #endif
 758
 759         UART_SET_IER(uart, ERBFI);
 760         return 0;
 761 }
 762
 763 static void bfin_serial_shutdown(struct uart_port *port)
 764 {
 765         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 766
 767 #ifdef CONFIG_SERIAL_BFIN_DMA
 768         disable_dma(uart->tx_dma_channel);
 769         free_dma(uart->tx_dma_channel);
 770         disable_dma(uart->rx_dma_channel);
 771         free_dma(uart->rx_dma_channel);
 772         del_timer(&(uart->rx_dma_timer));
 773         dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
 774 #else
 775 #ifdef CONFIG_BF54x
 776         switch (uart->port.irq) {
 777         case IRQ_UART3_RX:
 778                 free_dma(CH_UART3_RX);
 779                 free_dma(CH_UART3_TX);
 780                 break;
 781         case IRQ_UART2_RX:
 782                 free_dma(CH_UART2_RX);
 783                 free_dma(CH_UART2_TX);
 784                 break;
 785         default:
 786                 break;
 787         };
 788 #endif
 789         free_irq(uart->port.irq, uart);
 790         free_irq(uart->port.irq+1, uart);
 791 #endif
 792
 793 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
 794         if (uart->cts_pin >= 0)
 795                 free_irq(gpio_to_irq(uart->cts_pin), uart);
 796         if (uart->rts_pin >= 0)
 797                 gpio_free(uart->rts_pin);
 798 #endif
 799 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
 800         if (uart->cts_pin >= 0)
 801                 gpio_free(uart->cts_pin);
 802         if (uart->rts_pin >= 0)
 803                 gpio_free(uart->rts_pin);
 804         if (UART_GET_IER(uart) && EDSSI)
 805                 free_irq(uart->status_irq, uart);
 806 #endif
 807 }
 808
 809 static void
 810 bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
 811                    struct ktermios *old)
 812 {
 813         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 814         unsigned long flags;
 815         unsigned int baud, quot;
 816         unsigned short val, ier, lcr = 0;
 817
 818         switch (termios->c_cflag & CSIZE) {
 819         case CS8:
 820                 lcr = WLS(8);
 821                 break;
 822         case CS7:
 823                 lcr = WLS(7);
 824                 break;
 825         case CS6:
 826                 lcr = WLS(6);
 827                 break;
 828         case CS5:
 829                 lcr = WLS(5);
 830                 break;
 831         default:
 832                 printk(KERN_ERR "%s: word lengh not supported\n",
 833                         __func__);
 834         }
 835
 836         /* Anomaly notes:
 837          *  05000231 -  STOP bit is always set to 1 whatever the user is set.
 838          */
 839         if (termios->c_cflag & CSTOPB) {
 840                 if (ANOMALY_05000231)
 841                         printk(KERN_WARNING "STOP bits other than 1 is not "
 842                                 "supported in case of anomaly 05000231.\n");
 843                 else
 844                         lcr |= STB;
 845         }
 846         if (termios->c_cflag & PARENB)
 847                 lcr |= PEN;
 848         if (!(termios->c_cflag & PARODD))
 849                 lcr |= EPS;
 850         if (termios->c_cflag & CMSPAR)
 851                 lcr |= STP;
 852
 853         port->read_status_mask = OE;
 854         if (termios->c_iflag & INPCK)
 855                 port->read_status_mask |= (FE | PE);
 856         if (termios->c_iflag & (BRKINT | PARMRK))
 857                 port->read_status_mask |= BI;
 858
 859         /*
 860          * Characters to ignore
 861          */
 862         port->ignore_status_mask = 0;
 863         if (termios->c_iflag & IGNPAR)
 864                 port->ignore_status_mask |= FE | PE;
 865         if (termios->c_iflag & IGNBRK) {
 866                 port->ignore_status_mask |= BI;
 867                 /*
 868                  * If we're ignoring parity and break indicators,
 869                  * ignore overruns too (for real raw support).
 870                  */
 871                 if (termios->c_iflag & IGNPAR)
 872                         port->ignore_status_mask |= OE;
 873         }
 874
 875         baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 876         quot = uart_get_divisor(port, baud) - ANOMALY_05000230;
 877         spin_lock_irqsave(&uart->port.lock, flags);
 878
 879         UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
 880
 881         /* Disable UART */
 882         ier = UART_GET_IER(uart);
 883         UART_DISABLE_INTS(uart);
 884
 885         /* Set DLAB in LCR to Access DLL and DLH */
 886         UART_SET_DLAB(uart);
 887
 888         UART_PUT_DLL(uart, quot & 0xFF);
 889         UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
 890         SSYNC();
 891
 892         /* Clear DLAB in LCR to Access THR RBR IER */
 893         UART_CLEAR_DLAB(uart);
 894
 895         UART_PUT_LCR(uart, lcr);
 896
 897         /* Enable UART */
 898         UART_ENABLE_INTS(uart, ier);
 899
 900         val = UART_GET_GCTL(uart);
 901         val |= UCEN;
 902         UART_PUT_GCTL(uart, val);
 903
 904         /* Port speed changed, update the per-port timeout. */
 905         uart_update_timeout(port, termios->c_cflag, baud);
 906
 907         spin_unlock_irqrestore(&uart->port.lock, flags);
 908 }
 909
 910 static const char *bfin_serial_type(struct uart_port *port)
 911 {
 912         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 913
 914         return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
 915 }
 916
 917 /*
 918  * Release the memory region(s) being used by 'port'.
 919  */
 920 static void bfin_serial_release_port(struct uart_port *port)
 921 {
 922 }
 923
 924 /*
 925  * Request the memory region(s) being used by 'port'.
 926  */
 927 static int bfin_serial_request_port(struct uart_port *port)
 928 {
 929         return 0;
 930 }
 931
 932 /*
 933  * Configure/autoconfigure the port.
 934  */
 935 static void bfin_serial_config_port(struct uart_port *port, int flags)
 936 {
 937         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 938
 939         if (flags & UART_CONFIG_TYPE &&
 940             bfin_serial_request_port(&uart->port) == 0)
 941                 uart->port.type = PORT_BFIN;
 942 }
 943
 944 /*
 945  * Verify the new serial_struct (for TIOCSSERIAL).
 946  * The only change we allow are to the flags and type, and
 947  * even then only between PORT_BFIN and PORT_UNKNOWN
 948  */
 949 static int
 950 bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
 951 {
 952         return 0;
 953 }
 954
 955 /*
 956  * Enable the IrDA function if tty->ldisc.num is N_IRDA.
 957  * In other cases, disable IrDA function.
 958  */
 959 static void bfin_serial_set_ldisc(struct uart_port *port)
 960 {
 961         int line = port->line;
 962         unsigned short val;
 963
 964         if (line >= port->info->port.tty->driver->num)
 965                 return;
 966
 967         switch (port->info->port.tty->termios->c_line) {
 968         case N_IRDA:
 969                 val = UART_GET_GCTL(&bfin_serial_ports[line]);
 970                 val |= (IREN | RPOLC);
 971                 UART_PUT_GCTL(&bfin_serial_ports[line], val);
 972                 break;
 973         default:
 974                 val = UART_GET_GCTL(&bfin_serial_ports[line]);
 975                 val &= ~(IREN | RPOLC);
 976                 UART_PUT_GCTL(&bfin_serial_ports[line], val);
 977         }
 978 }
 979
 980 static void bfin_serial_reset_irda(struct uart_port *port)
 981 {
 982         int line = port->line;
 983         unsigned short val;
 984
 985         val = UART_GET_GCTL(&bfin_serial_ports[line]);
 986         val &= ~(IREN | RPOLC);
 987         UART_PUT_GCTL(&bfin_serial_ports[line], val);
 988         SSYNC();
 989         val |= (IREN | RPOLC);
 990         UART_PUT_GCTL(&bfin_serial_ports[line], val);
 991         SSYNC();
 992 }
 993
 994 #ifdef CONFIG_CONSOLE_POLL
 995 /* Anomaly notes:
 996  *  05000099 -  Because we only use THRE in poll_put and DR in poll_get,
 997  *              losing other bits of UART_LSR is not a problem here.
 998  */
 999 static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
1000 {
1001         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1002
1003         while (!(UART_GET_LSR(uart) & THRE))
1004                 cpu_relax();
1005
1006         UART_CLEAR_DLAB(uart);
1007         UART_PUT_CHAR(uart, (unsigned char)chr);
1008 }
1009
1010 static int bfin_serial_poll_get_char(struct uart_port *port)
1011 {
1012         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1013         unsigned char chr;
1014
1015         while (!(UART_GET_LSR(uart) & DR))
1016                 cpu_relax();
1017
1018         UART_CLEAR_DLAB(uart);
1019         chr = UART_GET_CHAR(uart);
1020
1021         return chr;
1022 }
1023 #endif
1024
1025 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
1026         defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
1027 static void bfin_kgdboc_port_shutdown(struct uart_port *port)
1028 {
1029         if (kgdboc_break_enabled) {
1030                 kgdboc_break_enabled = 0;
1031                 bfin_serial_shutdown(port);
1032         }
1033 }
1034
1035 static int bfin_kgdboc_port_startup(struct uart_port *port)
1036 {
1037         kgdboc_port_line = port->line;
1038         kgdboc_break_enabled = !bfin_serial_startup(port);
1039         return 0;
1040 }
1041 #endif
1042
1043 static struct uart_ops bfin_serial_pops = {
1044         .tx_empty       = bfin_serial_tx_empty,
1045         .set_mctrl      = bfin_serial_set_mctrl,
1046         .get_mctrl      = bfin_serial_get_mctrl,
1047         .stop_tx        = bfin_serial_stop_tx,
1048         .start_tx       = bfin_serial_start_tx,
1049         .stop_rx        = bfin_serial_stop_rx,
1050         .enable_ms      = bfin_serial_enable_ms,
1051         .break_ctl      = bfin_serial_break_ctl,
1052         .startup        = bfin_serial_startup,
1053         .shutdown       = bfin_serial_shutdown,
1054         .set_termios    = bfin_serial_set_termios,
1055         .set_ldisc      = bfin_serial_set_ldisc,
1056         .type           = bfin_serial_type,
1057         .release_port   = bfin_serial_release_port,
1058         .request_port   = bfin_serial_request_port,
1059         .config_port    = bfin_serial_config_port,
1060         .verify_port    = bfin_serial_verify_port,
1061 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
1062         defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
1063         .kgdboc_port_startup    = bfin_kgdboc_port_startup,
1064         .kgdboc_port_shutdown   = bfin_kgdboc_port_shutdown,
1065 #endif
1066 #ifdef CONFIG_CONSOLE_POLL
1067         .poll_put_char  = bfin_serial_poll_put_char,
1068         .poll_get_char  = bfin_serial_poll_get_char,
1069 #endif
1070 };
1071
1072 static void __init bfin_serial_hw_init(void)
1073 {
1074 #ifdef CONFIG_SERIAL_BFIN_UART0
1075         peripheral_request(P_UART0_TX, DRIVER_NAME);
1076         peripheral_request(P_UART0_RX, DRIVER_NAME);
1077 #endif
1078
1079 #ifdef CONFIG_SERIAL_BFIN_UART1
1080         peripheral_request(P_UART1_TX, DRIVER_NAME);
1081         peripheral_request(P_UART1_RX, DRIVER_NAME);
1082
1083 # if defined(CONFIG_BFIN_UART1_CTSRTS) && defined(CONFIG_BF54x)
1084         peripheral_request(P_UART1_RTS, DRIVER_NAME);
1085         peripheral_request(P_UART1_CTS, DRIVER_NAME);
1086 # endif
1087 #endif
1088
1089 #ifdef CONFIG_SERIAL_BFIN_UART2
1090         peripheral_request(P_UART2_TX, DRIVER_NAME);
1091         peripheral_request(P_UART2_RX, DRIVER_NAME);
1092 #endif
1093
1094 #ifdef CONFIG_SERIAL_BFIN_UART3
1095         peripheral_request(P_UART3_TX, DRIVER_NAME);
1096         peripheral_request(P_UART3_RX, DRIVER_NAME);
1097
1098 # if defined(CONFIG_BFIN_UART3_CTSRTS) && defined(CONFIG_BF54x)
1099         peripheral_request(P_UART3_RTS, DRIVER_NAME);
1100         peripheral_request(P_UART3_CTS, DRIVER_NAME);
1101 # endif
1102 #endif
1103 }
1104
1105 static void __init bfin_serial_init_ports(void)
1106 {
1107         static int first = 1;
1108         int i;
1109
1110         if (!first)
1111                 return;
1112         first = 0;
1113
1114         bfin_serial_hw_init();
1115
1116         for (i = 0; i < nr_active_ports; i++) {
1117                 spin_lock_init(&bfin_serial_ports[i].port.lock);
1118                 bfin_serial_ports[i].port.uartclk   = get_sclk();
1119                 bfin_serial_ports[i].port.fifosize  = BFIN_UART_TX_FIFO_SIZE;
1120                 bfin_serial_ports[i].port.ops       = &bfin_serial_pops;
1121                 bfin_serial_ports[i].port.line      = i;
1122                 bfin_serial_ports[i].port.iotype    = UPIO_MEM;
1123                 bfin_serial_ports[i].port.membase   =
1124                         (void __iomem *)bfin_serial_resource[i].uart_base_addr;
1125                 bfin_serial_ports[i].port.mapbase   =
1126                         bfin_serial_resource[i].uart_base_addr;
1127                 bfin_serial_ports[i].port.irq       =
1128                         bfin_serial_resource[i].uart_irq;
1129                 bfin_serial_ports[i].status_irq     =
1130                         bfin_serial_resource[i].uart_status_irq;
1131                 bfin_serial_ports[i].port.flags     = UPF_BOOT_AUTOCONF;
1132 #ifdef CONFIG_SERIAL_BFIN_DMA
1133                 bfin_serial_ports[i].tx_done        = 1;
1134                 bfin_serial_ports[i].tx_count       = 0;
1135                 bfin_serial_ports[i].tx_dma_channel =
1136                         bfin_serial_resource[i].uart_tx_dma_channel;
1137                 bfin_serial_ports[i].rx_dma_channel =
1138                         bfin_serial_resource[i].uart_rx_dma_channel;
1139                 init_timer(&(bfin_serial_ports[i].rx_dma_timer));
1140 #endif
1141 #if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1142         defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
1143                 bfin_serial_ports[i].cts_pin        =
1144                         bfin_serial_resource[i].uart_cts_pin;
1145                 bfin_serial_ports[i].rts_pin        =
1146                         bfin_serial_resource[i].uart_rts_pin;
1147 #endif
1148         }
1149 }
1150
1151 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
1152 /*
1153  * If the port was already initialised (eg, by a boot loader),
1154  * try to determine the current setup.
1155  */
1156 static void __init
1157 bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
1158                            int *parity, int *bits)
1159 {
1160         unsigned short status;
1161
1162         status = UART_GET_IER(uart) & (ERBFI | ETBEI);
1163         if (status == (ERBFI | ETBEI)) {
1164                 /* ok, the port was enabled */
1165                 u16 lcr, dlh, dll;
1166
1167                 lcr = UART_GET_LCR(uart);
1168
1169                 *parity = 'n';
1170                 if (lcr & PEN) {
1171                         if (lcr & EPS)
1172                                 *parity = 'e';
1173                         else
1174                                 *parity = 'o';
1175                 }
1176                 switch (lcr & 0x03) {
1177                         case 0: *bits = 5; break;
1178                         case 1: *bits = 6; break;
1179                         case 2: *bits = 7; break;
1180                         case 3: *bits = 8; break;
1181                 }
1182                 /* Set DLAB in LCR to Access DLL and DLH */
1183                 UART_SET_DLAB(uart);
1184
1185                 dll = UART_GET_DLL(uart);
1186                 dlh = UART_GET_DLH(uart);
1187
1188                 /* Clear DLAB in LCR to Access THR RBR IER */
1189                 UART_CLEAR_DLAB(uart);
1190
1191                 *baud = get_sclk() / (16*(dll | dlh << 8));
1192         }
1193         pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
1194 }
1195
1196 static struct uart_driver bfin_serial_reg;
1197
1198 static int __init
1199 bfin_serial_console_setup(struct console *co, char *options)
1200 {
1201         struct bfin_serial_port *uart;
1202         int baud = 57600;
1203         int bits = 8;
1204         int parity = 'n';
1205 # if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1206         defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
1207         int flow = 'r';
1208 # else
1209         int flow = 'n';
1210 # endif
1211
1212         /*
1213          * Check whether an invalid uart number has been specified, and
1214          * if so, search for the first available port that does have
1215          * console support.
1216          */
1217         if (co->index == -1 || co->index >= nr_active_ports)
1218                 co->index = 0;
1219         uart = &bfin_serial_ports[co->index];
1220
1221         if (options)
1222                 uart_parse_options(options, &baud, &parity, &bits, &flow);
1223         else
1224                 bfin_serial_console_get_options(uart, &baud, &parity, &bits);
1225
1226         return uart_set_options(&uart->port, co, baud, parity, bits, flow);
1227 }
1228 #endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
1229                                  defined (CONFIG_EARLY_PRINTK) */
1230
1231 #ifdef CONFIG_SERIAL_BFIN_CONSOLE
1232 static void bfin_serial_console_putchar(struct uart_port *port, int ch)
1233 {
1234         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1235         while (!(UART_GET_LSR(uart) & THRE))
1236                 barrier();
1237         UART_PUT_CHAR(uart, ch);
1238         SSYNC();
1239 }
1240
1241 /*
1242  * Interrupts are disabled on entering
1243  */
1244 static void
1245 bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
1246 {
1247         struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
1248         unsigned long flags;
1249
1250         spin_lock_irqsave(&uart->port.lock, flags);
1251         uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
1252         spin_unlock_irqrestore(&uart->port.lock, flags);
1253
1254 }
1255
1256 static struct console bfin_serial_console = {
1257         .name           = BFIN_SERIAL_NAME,
1258         .write          = bfin_serial_console_write,
1259         .device         = uart_console_device,
1260         .setup          = bfin_serial_console_setup,
1261         .flags          = CON_PRINTBUFFER,
1262         .index          = -1,
1263         .data           = &bfin_serial_reg,
1264 };
1265
1266 static int __init bfin_serial_rs_console_init(void)
1267 {
1268         bfin_serial_init_ports();
1269         register_console(&bfin_serial_console);
1270
1271         return 0;
1272 }
1273 console_initcall(bfin_serial_rs_console_init);
1274
1275 #define BFIN_SERIAL_CONSOLE     &bfin_serial_console
1276 #else
1277 #define BFIN_SERIAL_CONSOLE     NULL
1278 #endif /* CONFIG_SERIAL_BFIN_CONSOLE */
1279
1280
1281 #ifdef CONFIG_EARLY_PRINTK
1282 static __init void early_serial_putc(struct uart_port *port, int ch)
1283 {
1284         unsigned timeout = 0xffff;
1285         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1286
1287         while ((!(UART_GET_LSR(uart) & THRE)) && --timeout)
1288                 cpu_relax();
1289         UART_PUT_CHAR(uart, ch);
1290 }
1291
1292 static __init void early_serial_write(struct console *con, const char *s,
1293                                         unsigned int n)
1294 {
1295         struct bfin_serial_port *uart = &bfin_serial_ports[con->index];
1296         unsigned int i;
1297
1298         for (i = 0; i < n; i++, s++) {
1299                 if (*s == '\n')
1300                         early_serial_putc(&uart->port, '\r');
1301                 early_serial_putc(&uart->port, *s);
1302         }
1303 }
1304
1305 /*
1306  * This should have a .setup or .early_setup in it, but then things get called
1307  * without the command line options, and the baud rate gets messed up - so
1308  * don't let the common infrastructure play with things. (see calls to setup
1309  * & earlysetup in ./kernel/printk.c:register_console()
1310  */
1311 static struct __initdata console bfin_early_serial_console = {
1312         .name = "early_BFuart",
1313         .write = early_serial_write,
1314         .device = uart_console_device,
1315         .flags = CON_PRINTBUFFER,
1316         .index = -1,
1317         .data  = &bfin_serial_reg,
1318 };
1319
1320 struct console __init *bfin_earlyserial_init(unsigned int port,
1321                                                 unsigned int cflag)
1322 {
1323         struct bfin_serial_port *uart;
1324         struct ktermios t;
1325
1326         if (port == -1 || port >= nr_active_ports)
1327                 port = 0;
1328         bfin_serial_init_ports();
1329         bfin_early_serial_console.index = port;
1330         uart = &bfin_serial_ports[port];
1331         t.c_cflag = cflag;
1332         t.c_iflag = 0;
1333         t.c_oflag = 0;
1334         t.c_lflag = ICANON;
1335         t.c_line = port;
1336         bfin_serial_set_termios(&uart->port, &t, &t);
1337         return &bfin_early_serial_console;
1338 }
1339
1340 #endif /* CONFIG_EARLY_PRINTK */
1341
1342 static struct uart_driver bfin_serial_reg = {
1343         .owner                  = THIS_MODULE,
1344         .driver_name            = "bfin-uart",
1345         .dev_name               = BFIN_SERIAL_NAME,
1346         .major                  = BFIN_SERIAL_MAJOR,
1347         .minor                  = BFIN_SERIAL_MINOR,
1348         .nr                     = BFIN_UART_NR_PORTS,
1349         .cons                   = BFIN_SERIAL_CONSOLE,
1350 };
1351
1352 static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
1353 {
1354         int i;
1355
1356         for (i = 0; i < nr_active_ports; i++) {
1357                 if (bfin_serial_ports[i].port.dev != &dev->dev)
1358                         continue;
1359                 uart_suspend_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1360         }
1361
1362         return 0;
1363 }
1364
1365 static int bfin_serial_resume(struct platform_device *dev)
1366 {
1367         int i;
1368
1369         for (i = 0; i < nr_active_ports; i++) {
1370                 if (bfin_serial_ports[i].port.dev != &dev->dev)
1371                         continue;
1372                 uart_resume_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1373         }
1374
1375         return 0;
1376 }
1377
1378 static int bfin_serial_probe(struct platform_device *dev)
1379 {
1380         struct resource *res = dev->resource;
1381         int i;
1382
1383         for (i = 0; i < dev->num_resources; i++, res++)
1384                 if (res->flags & IORESOURCE_MEM)
1385                         break;
1386
1387         if (i < dev->num_resources) {
1388                 for (i = 0; i < nr_active_ports; i++, res++) {
1389                         if (bfin_serial_ports[i].port.mapbase != res->start)
1390                                 continue;
1391                         bfin_serial_ports[i].port.dev = &dev->dev;
1392                         uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1393                 }
1394         }
1395
1396         return 0;
1397 }
1398
1399 static int bfin_serial_remove(struct platform_device *dev)
1400 {
1401         int i;
1402
1403         for (i = 0; i < nr_active_ports; i++) {
1404                 if (bfin_serial_ports[i].port.dev != &dev->dev)
1405                         continue;
1406                 uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1407                 bfin_serial_ports[i].port.dev = NULL;
1408 #if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1409         defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
1410                 gpio_free(bfin_serial_ports[i].cts_pin);
1411                 gpio_free(bfin_serial_ports[i].rts_pin);
1412 #endif
1413         }
1414
1415         return 0;
1416 }
1417
1418 static struct platform_driver bfin_serial_driver = {
1419         .probe          = bfin_serial_probe,
1420         .remove         = bfin_serial_remove,
1421         .suspend        = bfin_serial_suspend,
1422         .resume         = bfin_serial_resume,
1423         .driver         = {
1424                 .name   = "bfin-uart",
1425                 .owner  = THIS_MODULE,
1426         },
1427 };
1428
1429 static int __init bfin_serial_init(void)
1430 {
1431         int ret;
1432
1433         pr_info("Serial: Blackfin serial driver\n");
1434
1435         bfin_serial_init_ports();
1436
1437         ret = uart_register_driver(&bfin_serial_reg);
1438         if (ret == 0) {
1439                 ret = platform_driver_register(&bfin_serial_driver);
1440                 if (ret) {
1441                         pr_debug("uart register failed\n");
1442                         uart_unregister_driver(&bfin_serial_reg);
1443                 }
1444         }
1445         return ret;
1446 }
1447
1448 static void __exit bfin_serial_exit(void)
1449 {
1450         platform_driver_unregister(&bfin_serial_driver);
1451         uart_unregister_driver(&bfin_serial_reg);
1452 }
1453
1454
1455 module_init(bfin_serial_init);
1456 module_exit(bfin_serial_exit);
1457
1458 MODULE_AUTHOR("Aubrey.Li <aubrey.li@analog.com>");
1459 MODULE_DESCRIPTION("Blackfin generic serial port driver");
1460 MODULE_LICENSE("GPL");
1461 MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
1462 MODULE_ALIAS("platform:bfin-uart");