ALSA: usb-audio: add support for Akai MPD16
[safe/jmp/linux-2.6] / drivers / net / ewrk3.c
1 /*  ewrk3.c: A DIGITAL EtherWORKS 3 ethernet driver for Linux.
2
3    Written 1994 by David C. Davies.
4
5    Copyright 1994 Digital Equipment Corporation.
6
7    This software may be used and distributed according to the terms of
8    the GNU General Public License, incorporated herein by reference.
9
10    This driver is written for the Digital Equipment Corporation series
11    of EtherWORKS ethernet cards:
12
13    DE203 Turbo (BNC)
14    DE204 Turbo (TP)
15    DE205 Turbo (TP BNC)
16
17    The driver has been tested on a relatively busy  network using the DE205
18    card and benchmarked with 'ttcp': it transferred 16M  of data at 975kB/s
19    (7.8Mb/s) to a DECstation 5000/200.
20
21    The author may be reached at davies@maniac.ultranet.com.
22
23    =========================================================================
24    This driver has been written  substantially  from scratch, although  its
25    inheritance of style and stack interface from 'depca.c' and in turn from
26    Donald Becker's 'lance.c' should be obvious.
27
28    The  DE203/4/5 boards  all  use a new proprietary   chip in place of the
29    LANCE chip used in prior cards  (DEPCA, DE100, DE200/1/2, DE210, DE422).
30    Use the depca.c driver in the standard distribution  for the LANCE based
31    cards from DIGITAL; this driver will not work with them.
32
33    The DE203/4/5 cards have 2  main modes: shared memory  and I/O only. I/O
34    only makes  all the card accesses through  I/O transactions and  no high
35    (shared)  memory is used. This  mode provides a >48% performance penalty
36    and  is deprecated in this  driver,  although allowed to provide initial
37    setup when hardstrapped.
38
39    The shared memory mode comes in 3 flavours: 2kB, 32kB and 64kB. There is
40    no point in using any mode other than the 2kB  mode - their performances
41    are virtually identical, although the driver has  been tested in the 2kB
42    and 32kB modes. I would suggest you uncomment the line:
43
44    FORCE_2K_MODE;
45
46    to allow the driver to configure the card as a  2kB card at your current
47    base  address, thus leaving more  room to clutter  your  system box with
48    other memory hungry boards.
49
50    As many ISA  and EISA cards  can be supported  under this driver  as you
51    wish, limited primarily  by the available IRQ lines,  rather than by the
52    available I/O addresses  (24 ISA,  16 EISA).   I have  checked different
53    configurations of  multiple  depca cards and  ewrk3 cards  and have  not
54    found a problem yet (provided you have at least depca.c v0.38) ...
55
56    The board IRQ setting   must be at  an unused  IRQ which is  auto-probed
57    using  Donald  Becker's autoprobe  routines.   All  these cards   are at
58    {5,10,11,15}.
59
60    No 16MB memory  limitation should exist with this  driver as DMA is  not
61    used and the common memory area is in low memory on the network card (my
62    current system has 20MB and I've not had problems yet).
63
64    The ability to load  this driver as a  loadable module has been included
65    and used  extensively during the  driver development (to save those long
66    reboot sequences). To utilise this ability, you have to do 8 things:
67
68    0) have a copy of the loadable modules code installed on your system.
69    1) copy ewrk3.c from the  /linux/drivers/net directory to your favourite
70    temporary directory.
71    2) edit the  source code near  line 1898 to reflect  the I/O address and
72    IRQ you're using.
73    3) compile  ewrk3.c, but include -DMODULE in  the command line to ensure
74    that the correct bits are compiled (see end of source code).
75    4) if you are wanting to add a new  card, goto 5. Otherwise, recompile a
76    kernel with the ewrk3 configuration turned off and reboot.
77    5) insmod ewrk3.o
78    [Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
79    [Adam Kropelin: now accepts irq=x1,x2 io=y1,y2 for multiple cards]
80    6) run the net startup bits for your new eth?? interface manually
81    (usually /etc/rc.inet[12] at boot time).
82    7) enjoy!
83
84    Note that autoprobing is not allowed in loadable modules - the system is
85    already up and running and you're messing with interrupts.
86
87    To unload a module, turn off the associated interface
88    'ifconfig eth?? down' then 'rmmod ewrk3'.
89
90    Promiscuous   mode has been  turned  off  in this driver,   but  all the
91    multicast  address bits  have been   turned on. This  improved the  send
92    performance on a busy network by about 13%.
93
94    Ioctl's have now been provided (primarily because  I wanted to grab some
95    packet size statistics). They  are patterned after 'plipconfig.c' from a
96    suggestion by Alan Cox.  Using these  ioctls, you can enable promiscuous
97    mode, add/delete multicast  addresses, change the hardware address,  get
98    packet size distribution statistics and muck around with the control and
99    status register. I'll add others if and when the need arises.
100
101    TO DO:
102    ------
103
104
105    Revision History
106    ----------------
107
108    Version   Date        Description
109
110    0.1     26-aug-94   Initial writing. ALPHA code release.
111    0.11    31-aug-94   Fixed: 2k mode memory base calc.,
112    LeMAC version calc.,
113    IRQ vector assignments during autoprobe.
114    0.12    31-aug-94   Tested working on LeMAC2 (DE20[345]-AC) card.
115    Fixed up MCA hash table algorithm.
116    0.20     4-sep-94   Added IOCTL functionality.
117    0.21    14-sep-94   Added I/O mode.
118    0.21axp 15-sep-94   Special version for ALPHA AXP Linux V1.0.
119    0.22    16-sep-94   Added more IOCTLs & tidied up.
120    0.23    21-sep-94   Added transmit cut through.
121    0.24    31-oct-94   Added uid checks in some ioctls.
122    0.30     1-nov-94   BETA code release.
123    0.31     5-dec-94   Added check/allocate region code.
124    0.32    16-jan-95   Broadcast packet fix.
125    0.33    10-Feb-95   Fix recognition bug reported by <bkm@star.rl.ac.uk>.
126    0.40    27-Dec-95   Rationalise MODULE and autoprobe code.
127    Rewrite for portability & updated.
128    ALPHA support from <jestabro@amt.tay1.dec.com>
129    Added verify_area() calls in ewrk3_ioctl() from
130    suggestion by <heiko@colossus.escape.de>.
131    Add new multicasting code.
132    0.41    20-Jan-96   Fix IRQ set up problem reported by
133    <kenneth@bbs.sas.ntu.ac.sg>.
134    0.42    22-Apr-96   Fix alloc_device() bug <jari@markkus2.fimr.fi>
135    0.43    16-Aug-96   Update alloc_device() to conform to de4x5.c
136    0.44    08-Nov-01   use library crc32 functions <Matt_Domsch@dell.com>
137    0.45    19-Jul-02   fix unaligned access on alpha <martin@bruli.net>
138    0.46    10-Oct-02   Multiple NIC support when module <akropel1@rochester.rr.com>
139    0.47    18-Oct-02   ethtool support <akropel1@rochester.rr.com>
140    0.48    18-Oct-02   cli/sti removal for 2.5 <vda@port.imtp.ilyichevsk.odessa.ua>
141    ioctl locking, signature search cleanup <akropel1@rochester.rr.com>
142
143    =========================================================================
144  */
145
146 #include <linux/module.h>
147 #include <linux/kernel.h>
148 #include <linux/sched.h>
149 #include <linux/string.h>
150 #include <linux/errno.h>
151 #include <linux/ioport.h>
152 #include <linux/slab.h>
153 #include <linux/interrupt.h>
154 #include <linux/delay.h>
155 #include <linux/init.h>
156 #include <linux/crc32.h>
157 #include <linux/netdevice.h>
158 #include <linux/etherdevice.h>
159 #include <linux/skbuff.h>
160 #include <linux/ethtool.h>
161 #include <linux/time.h>
162 #include <linux/types.h>
163 #include <linux/unistd.h>
164 #include <linux/ctype.h>
165 #include <linux/bitops.h>
166
167 #include <asm/io.h>
168 #include <asm/dma.h>
169 #include <asm/uaccess.h>
170
171 #include "ewrk3.h"
172
173 #define DRV_NAME        "ewrk3"
174 #define DRV_VERSION     "0.48"
175
176 static char version[] __initdata =
177 DRV_NAME ":v" DRV_VERSION " 2002/10/18 davies@maniac.ultranet.com\n";
178
179 #ifdef EWRK3_DEBUG
180 static int ewrk3_debug = EWRK3_DEBUG;
181 #else
182 static int ewrk3_debug = 1;
183 #endif
184
185 #define EWRK3_NDA 0xffe0        /* No Device Address */
186
187 #define PROBE_LENGTH    32
188 #define ETH_PROM_SIG    0xAA5500FFUL
189
190 #ifndef EWRK3_SIGNATURE
191 #define EWRK3_SIGNATURE {"DE203","DE204","DE205",""}
192 #define EWRK3_STRLEN 8
193 #endif
194
195 #ifndef EWRK3_RAM_BASE_ADDRESSES
196 #define EWRK3_RAM_BASE_ADDRESSES {0xc0000,0xd0000,0x00000}
197 #endif
198
199 /*
200    ** Sets up the I/O area for the autoprobe.
201  */
202 #define EWRK3_IO_BASE 0x100     /* Start address for probe search */
203 #define EWRK3_IOP_INC 0x20      /* I/O address increment */
204 #define EWRK3_TOTAL_SIZE 0x20   /* required I/O address length */
205
206 #ifndef MAX_NUM_EWRK3S
207 #define MAX_NUM_EWRK3S 21
208 #endif
209
210 #ifndef EWRK3_EISA_IO_PORTS
211 #define EWRK3_EISA_IO_PORTS 0x0c00      /* I/O port base address, slot 0 */
212 #endif
213
214 #ifndef MAX_EISA_SLOTS
215 #define MAX_EISA_SLOTS 16
216 #define EISA_SLOT_INC 0x1000
217 #endif
218
219 #define QUEUE_PKT_TIMEOUT (1*HZ)        /* Jiffies */
220
221 /*
222    ** EtherWORKS 3 shared memory window sizes
223  */
224 #define IO_ONLY         0x00
225 #define SHMEM_2K        0x800
226 #define SHMEM_32K       0x8000
227 #define SHMEM_64K       0x10000
228
229 /*
230    ** EtherWORKS 3 IRQ ENABLE/DISABLE
231  */
232 #define ENABLE_IRQs { \
233   icr |= lp->irq_mask;\
234   outb(icr, EWRK3_ICR);                     /* Enable the IRQs */\
235 }
236
237 #define DISABLE_IRQs { \
238   icr = inb(EWRK3_ICR);\
239   icr &= ~lp->irq_mask;\
240   outb(icr, EWRK3_ICR);                     /* Disable the IRQs */\
241 }
242
243 /*
244    ** EtherWORKS 3 START/STOP
245  */
246 #define START_EWRK3 { \
247   csr = inb(EWRK3_CSR);\
248   csr &= ~(CSR_TXD|CSR_RXD);\
249   outb(csr, EWRK3_CSR);                     /* Enable the TX and/or RX */\
250 }
251
252 #define STOP_EWRK3 { \
253   csr = (CSR_TXD|CSR_RXD);\
254   outb(csr, EWRK3_CSR);                     /* Disable the TX and/or RX */\
255 }
256
257 /*
258    ** The EtherWORKS 3 private structure
259  */
260 #define EWRK3_PKT_STAT_SZ 16
261 #define EWRK3_PKT_BIN_SZ  128   /* Should be >=100 unless you
262                                    increase EWRK3_PKT_STAT_SZ */
263
264 struct ewrk3_stats {
265         u32 bins[EWRK3_PKT_STAT_SZ];
266         u32 unicast;
267         u32 multicast;
268         u32 broadcast;
269         u32 excessive_collisions;
270         u32 tx_underruns;
271         u32 excessive_underruns;
272 };
273
274 struct ewrk3_private {
275         char adapter_name[80];  /* Name exported to /proc/ioports */
276         u_long shmem_base;      /* Shared memory start address */
277         void __iomem *shmem;
278         u_long shmem_length;    /* Shared memory window length */
279         struct ewrk3_stats pktStats; /* Private stats counters */
280         u_char irq_mask;        /* Adapter IRQ mask bits */
281         u_char mPage;           /* Maximum 2kB Page number */
282         u_char lemac;           /* Chip rev. level */
283         u_char hard_strapped;   /* Don't allow a full open */
284         u_char txc;             /* Transmit cut through */
285         void __iomem *mctbl;    /* Pointer to the multicast table */
286         u_char led_mask;        /* Used to reserve LED access for ethtool */
287         spinlock_t hw_lock;
288 };
289
290 /*
291    ** Force the EtherWORKS 3 card to be in 2kB MODE
292  */
293 #define FORCE_2K_MODE { \
294   shmem_length = SHMEM_2K;\
295   outb(((mem_start - 0x80000) >> 11), EWRK3_MBR);\
296 }
297
298 /*
299    ** Public Functions
300  */
301 static int ewrk3_open(struct net_device *dev);
302 static netdev_tx_t ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev);
303 static irqreturn_t ewrk3_interrupt(int irq, void *dev_id);
304 static int ewrk3_close(struct net_device *dev);
305 static void set_multicast_list(struct net_device *dev);
306 static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
307 static const struct ethtool_ops ethtool_ops_203;
308 static const struct ethtool_ops ethtool_ops;
309
310 /*
311    ** Private functions
312  */
313 static int ewrk3_hw_init(struct net_device *dev, u_long iobase);
314 static void ewrk3_init(struct net_device *dev);
315 static int ewrk3_rx(struct net_device *dev);
316 static int ewrk3_tx(struct net_device *dev);
317 static void ewrk3_timeout(struct net_device *dev);
318
319 static void EthwrkSignature(char *name, char *eeprom_image);
320 static int DevicePresent(u_long iobase);
321 static void SetMulticastFilter(struct net_device *dev);
322 static int EISA_signature(char *name, s32 eisa_id);
323
324 static int Read_EEPROM(u_long iobase, u_char eaddr);
325 static int Write_EEPROM(short data, u_long iobase, u_char eaddr);
326 static u_char get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType);
327
328 static int ewrk3_probe1(struct net_device *dev, u_long iobase, int irq);
329 static int isa_probe(struct net_device *dev, u_long iobase);
330 static int eisa_probe(struct net_device *dev, u_long iobase);
331
332 static u_char irq[MAX_NUM_EWRK3S+1] = {5, 0, 10, 3, 11, 9, 15, 12};
333
334 static char name[EWRK3_STRLEN + 1];
335 static int num_ewrks3s;
336
337 /*
338    ** Miscellaneous defines...
339  */
340 #define INIT_EWRK3 {\
341     outb(EEPROM_INIT, EWRK3_IOPR);\
342     mdelay(1);\
343 }
344
345 #ifndef MODULE
346 struct net_device * __init ewrk3_probe(int unit)
347 {
348         struct net_device *dev = alloc_etherdev(sizeof(struct ewrk3_private));
349         int err;
350
351         if (!dev)
352                 return ERR_PTR(-ENOMEM);
353
354         if (unit >= 0) {
355                 sprintf(dev->name, "eth%d", unit);
356                 netdev_boot_setup_check(dev);
357         }
358
359         err = ewrk3_probe1(dev, dev->base_addr, dev->irq);
360         if (err)
361                 goto out;
362         return dev;
363 out:
364         free_netdev(dev);
365         return ERR_PTR(err);
366
367 }
368 #endif
369
370 static int __init ewrk3_probe1(struct net_device *dev, u_long iobase, int irq)
371 {
372         int err;
373
374         dev->base_addr = iobase;
375         dev->irq = irq;
376
377         /* Address PROM pattern */
378         err = isa_probe(dev, iobase);
379         if (err != 0)
380                 err = eisa_probe(dev, iobase);
381
382         if (err)
383                 return err;
384
385         err = register_netdev(dev);
386         if (err)
387                 release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
388
389         return err;
390 }
391
392 static const struct net_device_ops ewrk3_netdev_ops = {
393         .ndo_open               = ewrk3_open,
394         .ndo_start_xmit         = ewrk3_queue_pkt,
395         .ndo_stop               = ewrk3_close,
396         .ndo_set_multicast_list = set_multicast_list,
397         .ndo_do_ioctl           = ewrk3_ioctl,
398         .ndo_tx_timeout         = ewrk3_timeout,
399         .ndo_change_mtu         = eth_change_mtu,
400         .ndo_set_mac_address    = eth_mac_addr,
401         .ndo_validate_addr      = eth_validate_addr,
402 };
403
404 static int __init
405 ewrk3_hw_init(struct net_device *dev, u_long iobase)
406 {
407         struct ewrk3_private *lp;
408         int i, status = 0;
409         u_long mem_start, shmem_length;
410         u_char cr, cmr, icr, nicsr, lemac, hard_strapped = 0;
411         u_char eeprom_image[EEPROM_MAX], chksum, eisa_cr = 0;
412
413         /*
414         ** Stop the EWRK3. Enable the DBR ROM. Disable interrupts and remote boot.
415         ** This also disables the EISA_ENABLE bit in the EISA Control Register.
416          */
417         if (iobase > 0x400)
418                 eisa_cr = inb(EISA_CR);
419         INIT_EWRK3;
420
421         nicsr = inb(EWRK3_CSR);
422
423         icr = inb(EWRK3_ICR);
424         icr &= 0x70;
425         outb(icr, EWRK3_ICR);   /* Disable all the IRQs */
426
427         if (nicsr != (CSR_TXD | CSR_RXD))
428                 return -ENXIO;
429
430         /* Check that the EEPROM is alive and well and not living on Pluto... */
431         for (chksum = 0, i = 0; i < EEPROM_MAX; i += 2) {
432                 union {
433                         short val;
434                         char c[2];
435                 } tmp;
436
437                 tmp.val = (short) Read_EEPROM(iobase, (i >> 1));
438                 eeprom_image[i] = tmp.c[0];
439                 eeprom_image[i + 1] = tmp.c[1];
440                 chksum += eeprom_image[i] + eeprom_image[i + 1];
441         }
442
443         if (chksum != 0) {      /* Bad EEPROM Data! */
444                 printk("%s: Device has a bad on-board EEPROM.\n", dev->name);
445                 return -ENXIO;
446         }
447
448         EthwrkSignature(name, eeprom_image);
449         if (*name == '\0')
450                 return -ENXIO;
451
452         dev->base_addr = iobase;
453
454         if (iobase > 0x400) {
455                 outb(eisa_cr, EISA_CR);         /* Rewrite the EISA CR */
456         }
457         lemac = eeprom_image[EEPROM_CHIPVER];
458         cmr = inb(EWRK3_CMR);
459
460         if (((lemac == LeMAC) && ((cmr & CMR_NO_EEPROM) != CMR_NO_EEPROM)) ||
461             ((lemac == LeMAC2) && !(cmr & CMR_HS))) {
462                 printk("%s: %s at %#4lx", dev->name, name, iobase);
463                 hard_strapped = 1;
464         } else if ((iobase & 0x0fff) == EWRK3_EISA_IO_PORTS) {
465                 /* EISA slot address */
466                 printk("%s: %s at %#4lx (EISA slot %ld)",
467                        dev->name, name, iobase, ((iobase >> 12) & 0x0f));
468         } else {        /* ISA port address */
469                 printk("%s: %s at %#4lx", dev->name, name, iobase);
470         }
471
472         printk(", h/w address ");
473         if (lemac != LeMAC2)
474                 DevicePresent(iobase);  /* need after EWRK3_INIT */
475         status = get_hw_addr(dev, eeprom_image, lemac);
476         printk("%pM\n", dev->dev_addr);
477
478         if (status) {
479                 printk("      which has an EEPROM CRC error.\n");
480                 return -ENXIO;
481         }
482
483         if (lemac == LeMAC2) {  /* Special LeMAC2 CMR things */
484                 cmr &= ~(CMR_RA | CMR_WB | CMR_LINK | CMR_POLARITY | CMR_0WS);
485                 if (eeprom_image[EEPROM_MISC0] & READ_AHEAD)
486                         cmr |= CMR_RA;
487                 if (eeprom_image[EEPROM_MISC0] & WRITE_BEHIND)
488                         cmr |= CMR_WB;
489                 if (eeprom_image[EEPROM_NETMAN0] & NETMAN_POL)
490                         cmr |= CMR_POLARITY;
491                 if (eeprom_image[EEPROM_NETMAN0] & NETMAN_LINK)
492                         cmr |= CMR_LINK;
493                 if (eeprom_image[EEPROM_MISC0] & _0WS_ENA)
494                         cmr |= CMR_0WS;
495         }
496         if (eeprom_image[EEPROM_SETUP] & SETUP_DRAM)
497                 cmr |= CMR_DRAM;
498         outb(cmr, EWRK3_CMR);
499
500         cr = inb(EWRK3_CR);     /* Set up the Control Register */
501         cr |= eeprom_image[EEPROM_SETUP] & SETUP_APD;
502         if (cr & SETUP_APD)
503                 cr |= eeprom_image[EEPROM_SETUP] & SETUP_PS;
504         cr |= eeprom_image[EEPROM_MISC0] & FAST_BUS;
505         cr |= eeprom_image[EEPROM_MISC0] & ENA_16;
506         outb(cr, EWRK3_CR);
507
508         /*
509         ** Determine the base address and window length for the EWRK3
510         ** RAM from the memory base register.
511         */
512         mem_start = inb(EWRK3_MBR);
513         shmem_length = 0;
514         if (mem_start != 0) {
515                 if ((mem_start >= 0x0a) && (mem_start <= 0x0f)) {
516                         mem_start *= SHMEM_64K;
517                         shmem_length = SHMEM_64K;
518                 } else if ((mem_start >= 0x14) && (mem_start <= 0x1f)) {
519                         mem_start *= SHMEM_32K;
520                         shmem_length = SHMEM_32K;
521                 } else if ((mem_start >= 0x40) && (mem_start <= 0xff)) {
522                         mem_start = mem_start * SHMEM_2K + 0x80000;
523                         shmem_length = SHMEM_2K;
524                 } else {
525                         return -ENXIO;
526                 }
527         }
528         /*
529         ** See the top of this source code for comments about
530         ** uncommenting this line.
531         */
532 /*          FORCE_2K_MODE; */
533
534         if (hard_strapped) {
535                 printk("      is hard strapped.\n");
536         } else if (mem_start) {
537                 printk("      has a %dk RAM window", (int) (shmem_length >> 10));
538                 printk(" at 0x%.5lx", mem_start);
539         } else {
540                 printk("      is in I/O only mode");
541         }
542
543         lp = netdev_priv(dev);
544         lp->shmem_base = mem_start;
545         lp->shmem = ioremap(mem_start, shmem_length);
546         if (!lp->shmem)
547                 return -ENOMEM;
548         lp->shmem_length = shmem_length;
549         lp->lemac = lemac;
550         lp->hard_strapped = hard_strapped;
551         lp->led_mask = CR_LED;
552         spin_lock_init(&lp->hw_lock);
553
554         lp->mPage = 64;
555         if (cmr & CMR_DRAM)
556                 lp->mPage <<= 1;        /* 2 DRAMS on module */
557
558         sprintf(lp->adapter_name, "%s (%s)", name, dev->name);
559
560         lp->irq_mask = ICR_TNEM | ICR_TXDM | ICR_RNEM | ICR_RXDM;
561
562         if (!hard_strapped) {
563                 /*
564                 ** Enable EWRK3 board interrupts for autoprobing
565                 */
566                 icr |= ICR_IE;  /* Enable interrupts */
567                 outb(icr, EWRK3_ICR);
568
569                 /* The DMA channel may be passed in on this parameter. */
570                 dev->dma = 0;
571
572                 /* To auto-IRQ we enable the initialization-done and DMA err,
573                    interrupts. For now we will always get a DMA error. */
574                 if (dev->irq < 2) {
575 #ifndef MODULE
576                         u_char irqnum;
577                         unsigned long irq_mask;
578
579
580                         irq_mask = probe_irq_on();
581
582                         /*
583                         ** Trigger a TNE interrupt.
584                         */
585                         icr |= ICR_TNEM;
586                         outb(1, EWRK3_TDQ);     /* Write to the TX done queue */
587                         outb(icr, EWRK3_ICR);   /* Unmask the TXD interrupt */
588
589                         irqnum = irq[((icr & IRQ_SEL) >> 4)];
590
591                         mdelay(20);
592                         dev->irq = probe_irq_off(irq_mask);
593                         if ((dev->irq) && (irqnum == dev->irq)) {
594                                 printk(" and uses IRQ%d.\n", dev->irq);
595                         } else {
596                                 if (!dev->irq) {
597                                         printk(" and failed to detect IRQ line.\n");
598                                 } else if ((irqnum == 1) && (lemac == LeMAC2)) {
599                                         printk(" and an illegal IRQ line detected.\n");
600                                 } else {
601                                         printk(", but incorrect IRQ line detected.\n");
602                                 }
603                                 iounmap(lp->shmem);
604                                 return -ENXIO;
605                         }
606
607                         DISABLE_IRQs;   /* Mask all interrupts */
608
609 #endif                          /* MODULE */
610                 } else {
611                         printk(" and requires IRQ%d.\n", dev->irq);
612                 }
613         }
614
615         if (ewrk3_debug > 1) {
616                 printk(version);
617         }
618         /* The EWRK3-specific entries in the device structure. */
619         dev->netdev_ops = &ewrk3_netdev_ops;
620         if (lp->adapter_name[4] == '3')
621                 SET_ETHTOOL_OPS(dev, &ethtool_ops_203);
622         else
623                 SET_ETHTOOL_OPS(dev, &ethtool_ops);
624         dev->watchdog_timeo = QUEUE_PKT_TIMEOUT;
625
626         dev->mem_start = 0;
627
628         return 0;
629 }
630
631
632 static int ewrk3_open(struct net_device *dev)
633 {
634         struct ewrk3_private *lp = netdev_priv(dev);
635         u_long iobase = dev->base_addr;
636         int status = 0;
637         u_char icr, csr;
638
639         /*
640            ** Stop the TX and RX...
641          */
642         STOP_EWRK3;
643
644         if (!lp->hard_strapped) {
645                 if (request_irq(dev->irq, (void *) ewrk3_interrupt, 0, "ewrk3", dev)) {
646                         printk("ewrk3_open(): Requested IRQ%d is busy\n", dev->irq);
647                         status = -EAGAIN;
648                 } else {
649
650                         /*
651                            ** Re-initialize the EWRK3...
652                          */
653                         ewrk3_init(dev);
654
655                         if (ewrk3_debug > 1) {
656                                 printk("%s: ewrk3 open with irq %d\n", dev->name, dev->irq);
657                                 printk("  physical address: %pM\n", dev->dev_addr);
658                                 if (lp->shmem_length == 0) {
659                                         printk("  no shared memory, I/O only mode\n");
660                                 } else {
661                                         printk("  start of shared memory: 0x%08lx\n", lp->shmem_base);
662                                         printk("  window length: 0x%04lx\n", lp->shmem_length);
663                                 }
664                                 printk("  # of DRAMS: %d\n", ((inb(EWRK3_CMR) & 0x02) ? 2 : 1));
665                                 printk("  csr:  0x%02x\n", inb(EWRK3_CSR));
666                                 printk("  cr:   0x%02x\n", inb(EWRK3_CR));
667                                 printk("  icr:  0x%02x\n", inb(EWRK3_ICR));
668                                 printk("  cmr:  0x%02x\n", inb(EWRK3_CMR));
669                                 printk("  fmqc: 0x%02x\n", inb(EWRK3_FMQC));
670                         }
671                         netif_start_queue(dev);
672                         /*
673                            ** Unmask EWRK3 board interrupts
674                          */
675                         icr = inb(EWRK3_ICR);
676                         ENABLE_IRQs;
677
678                 }
679         } else {
680                 printk(KERN_ERR "%s: ewrk3 available for hard strapped set up only.\n", dev->name);
681                 printk(KERN_ERR "      Run the 'ewrk3setup' utility or remove the hard straps.\n");
682                 return -EINVAL;
683         }
684
685         return status;
686 }
687
688 /*
689    ** Initialize the EtherWORKS 3 operating conditions
690  */
691 static void ewrk3_init(struct net_device *dev)
692 {
693         struct ewrk3_private *lp = netdev_priv(dev);
694         u_char csr, page;
695         u_long iobase = dev->base_addr;
696         int i;
697
698         /*
699            ** Enable any multicasts
700          */
701         set_multicast_list(dev);
702
703         /*
704         ** Set hardware MAC address. Address is initialized from the EEPROM
705         ** during startup but may have since been changed by the user.
706         */
707         for (i=0; i<ETH_ALEN; i++)
708                 outb(dev->dev_addr[i], EWRK3_PAR0 + i);
709
710         /*
711            ** Clean out any remaining entries in all the queues here
712          */
713         while (inb(EWRK3_TQ));
714         while (inb(EWRK3_TDQ));
715         while (inb(EWRK3_RQ));
716         while (inb(EWRK3_FMQ));
717
718         /*
719            ** Write a clean free memory queue
720          */
721         for (page = 1; page < lp->mPage; page++) {      /* Write the free page numbers */
722                 outb(page, EWRK3_FMQ);  /* to the Free Memory Queue */
723         }
724
725         START_EWRK3;            /* Enable the TX and/or RX */
726 }
727
728 /*
729  *  Transmit timeout
730  */
731
732 static void ewrk3_timeout(struct net_device *dev)
733 {
734         struct ewrk3_private *lp = netdev_priv(dev);
735         u_char icr, csr;
736         u_long iobase = dev->base_addr;
737
738         if (!lp->hard_strapped)
739         {
740                 printk(KERN_WARNING"%s: transmit timed/locked out, status %04x, resetting.\n",
741                        dev->name, inb(EWRK3_CSR));
742
743                 /*
744                    ** Mask all board interrupts
745                  */
746                 DISABLE_IRQs;
747
748                 /*
749                    ** Stop the TX and RX...
750                  */
751                 STOP_EWRK3;
752
753                 ewrk3_init(dev);
754
755                 /*
756                    ** Unmask EWRK3 board interrupts
757                  */
758                 ENABLE_IRQs;
759
760                 dev->trans_start = jiffies;
761                 netif_wake_queue(dev);
762         }
763 }
764
765 /*
766    ** Writes a socket buffer to the free page queue
767  */
768 static netdev_tx_t ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev)
769 {
770         struct ewrk3_private *lp = netdev_priv(dev);
771         u_long iobase = dev->base_addr;
772         void __iomem *buf = NULL;
773         u_char icr;
774         u_char page;
775
776         spin_lock_irq (&lp->hw_lock);
777         DISABLE_IRQs;
778
779         /* if no resources available, exit, request packet be queued */
780         if (inb (EWRK3_FMQC) == 0) {
781                 printk (KERN_WARNING "%s: ewrk3_queue_pkt(): No free resources...\n",
782                         dev->name);
783                 printk (KERN_WARNING "%s: ewrk3_queue_pkt(): CSR: %02x ICR: %02x FMQC: %02x\n",
784                         dev->name, inb (EWRK3_CSR), inb (EWRK3_ICR),
785                         inb (EWRK3_FMQC));
786                 goto err_out;
787         }
788
789         /*
790          ** Get a free page from the FMQ
791          */
792         if ((page = inb (EWRK3_FMQ)) >= lp->mPage) {
793                 printk ("ewrk3_queue_pkt(): Invalid free memory page (%d).\n",
794                      (u_char) page);
795                 goto err_out;
796         }
797
798
799         /*
800          ** Set up shared memory window and pointer into the window
801          */
802         if (lp->shmem_length == IO_ONLY) {
803                 outb (page, EWRK3_IOPR);
804         } else if (lp->shmem_length == SHMEM_2K) {
805                 buf = lp->shmem;
806                 outb (page, EWRK3_MPR);
807         } else if (lp->shmem_length == SHMEM_32K) {
808                 buf = (((short) page << 11) & 0x7800) + lp->shmem;
809                 outb ((page >> 4), EWRK3_MPR);
810         } else if (lp->shmem_length == SHMEM_64K) {
811                 buf = (((short) page << 11) & 0xf800) + lp->shmem;
812                 outb ((page >> 5), EWRK3_MPR);
813         } else {
814                 printk (KERN_ERR "%s: Oops - your private data area is hosed!\n",
815                         dev->name);
816                 BUG ();
817         }
818
819         /*
820          ** Set up the buffer control structures and copy the data from
821          ** the socket buffer to the shared memory .
822          */
823         if (lp->shmem_length == IO_ONLY) {
824                 int i;
825                 u_char *p = skb->data;
826                 outb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), EWRK3_DATA);
827                 outb ((char) (skb->len & 0xff), EWRK3_DATA);
828                 outb ((char) ((skb->len >> 8) & 0xff), EWRK3_DATA);
829                 outb ((char) 0x04, EWRK3_DATA);
830                 for (i = 0; i < skb->len; i++) {
831                         outb (*p++, EWRK3_DATA);
832                 }
833                 outb (page, EWRK3_TQ);  /* Start sending pkt */
834         } else {
835                 writeb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), buf);   /* ctrl byte */
836                 buf += 1;
837                 writeb ((char) (skb->len & 0xff), buf); /* length (16 bit xfer) */
838                 buf += 1;
839                 if (lp->txc) {
840                         writeb(((skb->len >> 8) & 0xff) | XCT, buf);
841                         buf += 1;
842                         writeb (0x04, buf);     /* index byte */
843                         buf += 1;
844                         writeb (0x00, (buf + skb->len));        /* Write the XCT flag */
845                         memcpy_toio (buf, skb->data, PRELOAD);  /* Write PRELOAD bytes */
846                         outb (page, EWRK3_TQ);  /* Start sending pkt */
847                         memcpy_toio (buf + PRELOAD,
848                                          skb->data + PRELOAD,
849                                          skb->len - PRELOAD);
850                         writeb (0xff, (buf + skb->len));        /* Write the XCT flag */
851                 } else {
852                         writeb ((skb->len >> 8) & 0xff, buf);
853                         buf += 1;
854                         writeb (0x04, buf);     /* index byte */
855                         buf += 1;
856                         memcpy_toio (buf, skb->data, skb->len); /* Write data bytes */
857                         outb (page, EWRK3_TQ);  /* Start sending pkt */
858                 }
859         }
860
861         ENABLE_IRQs;
862         spin_unlock_irq (&lp->hw_lock);
863
864         dev->stats.tx_bytes += skb->len;
865         dev->trans_start = jiffies;
866         dev_kfree_skb (skb);
867
868         /* Check for free resources: stop Tx queue if there are none */
869         if (inb (EWRK3_FMQC) == 0)
870                 netif_stop_queue (dev);
871
872         return NETDEV_TX_OK;
873
874 err_out:
875         ENABLE_IRQs;
876         spin_unlock_irq (&lp->hw_lock);
877         return NETDEV_TX_BUSY;
878 }
879
880 /*
881    ** The EWRK3 interrupt handler.
882  */
883 static irqreturn_t ewrk3_interrupt(int irq, void *dev_id)
884 {
885         struct net_device *dev = dev_id;
886         struct ewrk3_private *lp;
887         u_long iobase;
888         u_char icr, cr, csr;
889
890         lp = netdev_priv(dev);
891         iobase = dev->base_addr;
892
893         /* get the interrupt information */
894         csr = inb(EWRK3_CSR);
895
896         /*
897          ** Mask the EWRK3 board interrupts and turn on the LED
898          */
899         spin_lock(&lp->hw_lock);
900         DISABLE_IRQs;
901
902         cr = inb(EWRK3_CR);
903         cr |= lp->led_mask;
904         outb(cr, EWRK3_CR);
905
906         if (csr & CSR_RNE)      /* Rx interrupt (packet[s] arrived) */
907                 ewrk3_rx(dev);
908
909         if (csr & CSR_TNE)      /* Tx interrupt (packet sent) */
910                 ewrk3_tx(dev);
911
912         /*
913          ** Now deal with the TX/RX disable flags. These are set when there
914          ** are no more resources. If resources free up then enable these
915          ** interrupts, otherwise mask them - failure to do this will result
916          ** in the system hanging in an interrupt loop.
917          */
918         if (inb(EWRK3_FMQC)) {  /* any resources available? */
919                 lp->irq_mask |= ICR_TXDM | ICR_RXDM;    /* enable the interrupt source */
920                 csr &= ~(CSR_TXD | CSR_RXD);    /* ensure restart of a stalled TX or RX */
921                 outb(csr, EWRK3_CSR);
922                 netif_wake_queue(dev);
923         } else {
924                 lp->irq_mask &= ~(ICR_TXDM | ICR_RXDM);         /* disable the interrupt source */
925         }
926
927         /* Unmask the EWRK3 board interrupts and turn off the LED */
928         cr &= ~(lp->led_mask);
929         outb(cr, EWRK3_CR);
930         ENABLE_IRQs;
931         spin_unlock(&lp->hw_lock);
932         return IRQ_HANDLED;
933 }
934
935 /* Called with lp->hw_lock held */
936 static int ewrk3_rx(struct net_device *dev)
937 {
938         struct ewrk3_private *lp = netdev_priv(dev);
939         u_long iobase = dev->base_addr;
940         int i, status = 0;
941         u_char page;
942         void __iomem *buf = NULL;
943
944         while (inb(EWRK3_RQC) && !status) {     /* Whilst there's incoming data */
945                 if ((page = inb(EWRK3_RQ)) < lp->mPage) {       /* Get next entry's buffer page */
946                         /*
947                            ** Set up shared memory window and pointer into the window
948                          */
949                         if (lp->shmem_length == IO_ONLY) {
950                                 outb(page, EWRK3_IOPR);
951                         } else if (lp->shmem_length == SHMEM_2K) {
952                                 buf = lp->shmem;
953                                 outb(page, EWRK3_MPR);
954                         } else if (lp->shmem_length == SHMEM_32K) {
955                                 buf = (((short) page << 11) & 0x7800) + lp->shmem;
956                                 outb((page >> 4), EWRK3_MPR);
957                         } else if (lp->shmem_length == SHMEM_64K) {
958                                 buf = (((short) page << 11) & 0xf800) + lp->shmem;
959                                 outb((page >> 5), EWRK3_MPR);
960                         } else {
961                                 status = -1;
962                                 printk("%s: Oops - your private data area is hosed!\n", dev->name);
963                         }
964
965                         if (!status) {
966                                 char rx_status;
967                                 int pkt_len;
968
969                                 if (lp->shmem_length == IO_ONLY) {
970                                         rx_status = inb(EWRK3_DATA);
971                                         pkt_len = inb(EWRK3_DATA);
972                                         pkt_len |= ((u_short) inb(EWRK3_DATA) << 8);
973                                 } else {
974                                         rx_status = readb(buf);
975                                         buf += 1;
976                                         pkt_len = readw(buf);
977                                         buf += 3;
978                                 }
979
980                                 if (!(rx_status & R_ROK)) {     /* There was an error. */
981                                         dev->stats.rx_errors++; /* Update the error stats. */
982                                         if (rx_status & R_DBE)
983                                                 dev->stats.rx_frame_errors++;
984                                         if (rx_status & R_CRC)
985                                                 dev->stats.rx_crc_errors++;
986                                         if (rx_status & R_PLL)
987                                                 dev->stats.rx_fifo_errors++;
988                                 } else {
989                                         struct sk_buff *skb;
990
991                                         if ((skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
992                                                 unsigned char *p;
993                                                 skb_reserve(skb, 2);    /* Align to 16 bytes */
994                                                 p = skb_put(skb, pkt_len);
995
996                                                 if (lp->shmem_length == IO_ONLY) {
997                                                         *p = inb(EWRK3_DATA);   /* dummy read */
998                                                         for (i = 0; i < pkt_len; i++) {
999                                                                 *p++ = inb(EWRK3_DATA);
1000                                                         }
1001                                                 } else {
1002                                                         memcpy_fromio(p, buf, pkt_len);
1003                                                 }
1004
1005                                                 for (i = 1; i < EWRK3_PKT_STAT_SZ - 1; i++) {
1006                                                         if (pkt_len < i * EWRK3_PKT_BIN_SZ) {
1007                                                                 lp->pktStats.bins[i]++;
1008                                                                 i = EWRK3_PKT_STAT_SZ;
1009                                                         }
1010                                                 }
1011                                                 p = skb->data;  /* Look at the dest addr */
1012                                                 if (p[0] & 0x01) {      /* Multicast/Broadcast */
1013                                                         if ((*(s16 *) & p[0] == -1) && (*(s16 *) & p[2] == -1) && (*(s16 *) & p[4] == -1)) {
1014                                                                 lp->pktStats.broadcast++;
1015                                                         } else {
1016                                                                 lp->pktStats.multicast++;
1017                                                         }
1018                                                 } else if ((*(s16 *) & p[0] == *(s16 *) & dev->dev_addr[0]) &&
1019                                                            (*(s16 *) & p[2] == *(s16 *) & dev->dev_addr[2]) &&
1020                                                            (*(s16 *) & p[4] == *(s16 *) & dev->dev_addr[4])) {
1021                                                         lp->pktStats.unicast++;
1022                                                 }
1023                                                 lp->pktStats.bins[0]++;         /* Duplicates stats.rx_packets */
1024                                                 if (lp->pktStats.bins[0] == 0) {        /* Reset counters */
1025                                                         memset(&lp->pktStats, 0, sizeof(lp->pktStats));
1026                                                 }
1027                                                 /*
1028                                                    ** Notify the upper protocol layers that there is another
1029                                                    ** packet to handle
1030                                                  */
1031                                                 skb->protocol = eth_type_trans(skb, dev);
1032                                                 netif_rx(skb);
1033
1034                                                 /*
1035                                                    ** Update stats
1036                                                  */
1037                                                 dev->stats.rx_packets++;
1038                                                 dev->stats.rx_bytes += pkt_len;
1039                                         } else {
1040                                                 printk("%s: Insufficient memory; nuking packet.\n", dev->name);
1041                                                 dev->stats.rx_dropped++;                /* Really, deferred. */
1042                                                 break;
1043                                         }
1044                                 }
1045                         }
1046                         /*
1047                            ** Return the received buffer to the free memory queue
1048                          */
1049                         outb(page, EWRK3_FMQ);
1050                 } else {
1051                         printk("ewrk3_rx(): Illegal page number, page %d\n", page);
1052                         printk("ewrk3_rx(): CSR: %02x ICR: %02x FMQC: %02x\n", inb(EWRK3_CSR), inb(EWRK3_ICR), inb(EWRK3_FMQC));
1053                 }
1054         }
1055         return status;
1056 }
1057
1058 /*
1059 ** Buffer sent - check for TX buffer errors.
1060 ** Called with lp->hw_lock held
1061 */
1062 static int ewrk3_tx(struct net_device *dev)
1063 {
1064         struct ewrk3_private *lp = netdev_priv(dev);
1065         u_long iobase = dev->base_addr;
1066         u_char tx_status;
1067
1068         while ((tx_status = inb(EWRK3_TDQ)) > 0) {      /* Whilst there's old buffers */
1069                 if (tx_status & T_VSTS) {       /* The status is valid */
1070                         if (tx_status & T_TXE) {
1071                                 dev->stats.tx_errors++;
1072                                 if (tx_status & T_NCL)
1073                                         dev->stats.tx_carrier_errors++;
1074                                 if (tx_status & T_LCL)
1075                                         dev->stats.tx_window_errors++;
1076                                 if (tx_status & T_CTU) {
1077                                         if ((tx_status & T_COLL) ^ T_XUR) {
1078                                                 lp->pktStats.tx_underruns++;
1079                                         } else {
1080                                                 lp->pktStats.excessive_underruns++;
1081                                         }
1082                                 } else if (tx_status & T_COLL) {
1083                                         if ((tx_status & T_COLL) ^ T_XCOLL) {
1084                                                 dev->stats.collisions++;
1085                                         } else {
1086                                                 lp->pktStats.excessive_collisions++;
1087                                         }
1088                                 }
1089                         } else {
1090                                 dev->stats.tx_packets++;
1091                         }
1092                 }
1093         }
1094
1095         return 0;
1096 }
1097
1098 static int ewrk3_close(struct net_device *dev)
1099 {
1100         struct ewrk3_private *lp = netdev_priv(dev);
1101         u_long iobase = dev->base_addr;
1102         u_char icr, csr;
1103
1104         netif_stop_queue(dev);
1105
1106         if (ewrk3_debug > 1) {
1107                 printk("%s: Shutting down ethercard, status was %2.2x.\n",
1108                        dev->name, inb(EWRK3_CSR));
1109         }
1110         /*
1111            ** We stop the EWRK3 here... mask interrupts and stop TX & RX
1112          */
1113         DISABLE_IRQs;
1114
1115         STOP_EWRK3;
1116
1117         /*
1118            ** Clean out the TX and RX queues here (note that one entry
1119            ** may get added to either the TXD or RX queues if the TX or RX
1120            ** just starts processing a packet before the STOP_EWRK3 command
1121            ** is received. This will be flushed in the ewrk3_open() call).
1122          */
1123         while (inb(EWRK3_TQ));
1124         while (inb(EWRK3_TDQ));
1125         while (inb(EWRK3_RQ));
1126
1127         if (!lp->hard_strapped) {
1128                 free_irq(dev->irq, dev);
1129         }
1130         return 0;
1131 }
1132
1133 /*
1134    ** Set or clear the multicast filter for this adapter.
1135  */
1136 static void set_multicast_list(struct net_device *dev)
1137 {
1138         struct ewrk3_private *lp = netdev_priv(dev);
1139         u_long iobase = dev->base_addr;
1140         u_char csr;
1141
1142         csr = inb(EWRK3_CSR);
1143
1144         if (lp->shmem_length == IO_ONLY) {
1145                 lp->mctbl = NULL;
1146         } else {
1147                 lp->mctbl = lp->shmem + PAGE0_HTE;
1148         }
1149
1150         csr &= ~(CSR_PME | CSR_MCE);
1151         if (dev->flags & IFF_PROMISC) {         /* set promiscuous mode */
1152                 csr |= CSR_PME;
1153                 outb(csr, EWRK3_CSR);
1154         } else {
1155                 SetMulticastFilter(dev);
1156                 csr |= CSR_MCE;
1157                 outb(csr, EWRK3_CSR);
1158         }
1159 }
1160
1161 /*
1162    ** Calculate the hash code and update the logical address filter
1163    ** from a list of ethernet multicast addresses.
1164    ** Little endian crc one liner from Matt Thomas, DEC.
1165    **
1166    ** Note that when clearing the table, the broadcast bit must remain asserted
1167    ** to receive broadcast messages.
1168  */
1169 static void SetMulticastFilter(struct net_device *dev)
1170 {
1171         struct ewrk3_private *lp = netdev_priv(dev);
1172         struct dev_mc_list *dmi;
1173         u_long iobase = dev->base_addr;
1174         int i;
1175         char *addrs, bit, byte;
1176         short __iomem *p = lp->mctbl;
1177         u16 hashcode;
1178         u32 crc;
1179
1180         spin_lock_irq(&lp->hw_lock);
1181
1182         if (lp->shmem_length == IO_ONLY) {
1183                 outb(0, EWRK3_IOPR);
1184                 outw(PAGE0_HTE, EWRK3_PIR1);
1185         } else {
1186                 outb(0, EWRK3_MPR);
1187         }
1188
1189         if (dev->flags & IFF_ALLMULTI) {
1190                 for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
1191                         if (lp->shmem_length == IO_ONLY) {
1192                                 outb(0xff, EWRK3_DATA);
1193                         } else {        /* memset didn't work here */
1194                                 writew(0xffff, p);
1195                                 p++;
1196                                 i++;
1197                         }
1198                 }
1199         } else {
1200                 /* Clear table except for broadcast bit */
1201                 if (lp->shmem_length == IO_ONLY) {
1202                         for (i = 0; i < (HASH_TABLE_LEN >> 4) - 1; i++) {
1203                                 outb(0x00, EWRK3_DATA);
1204                         }
1205                         outb(0x80, EWRK3_DATA);
1206                         i++;    /* insert the broadcast bit */
1207                         for (; i < (HASH_TABLE_LEN >> 3); i++) {
1208                                 outb(0x00, EWRK3_DATA);
1209                         }
1210                 } else {
1211                         memset_io(lp->mctbl, 0, HASH_TABLE_LEN >> 3);
1212                         writeb(0x80, lp->mctbl + (HASH_TABLE_LEN >> 4) - 1);
1213                 }
1214
1215                 /* Update table */
1216                 netdev_for_each_mc_addr(dmi, dev) {
1217                         addrs = dmi->dmi_addr;
1218                         if ((*addrs & 0x01) == 1) {     /* multicast address? */
1219                                 crc = ether_crc_le(ETH_ALEN, addrs);
1220                                 hashcode = crc & ((1 << 9) - 1);        /* hashcode is 9 LSb of CRC */
1221
1222                                 byte = hashcode >> 3;   /* bit[3-8] -> byte in filter */
1223                                 bit = 1 << (hashcode & 0x07);   /* bit[0-2] -> bit in byte */
1224
1225                                 if (lp->shmem_length == IO_ONLY) {
1226                                         u_char tmp;
1227
1228                                         outw(PAGE0_HTE + byte, EWRK3_PIR1);
1229                                         tmp = inb(EWRK3_DATA);
1230                                         tmp |= bit;
1231                                         outw(PAGE0_HTE + byte, EWRK3_PIR1);
1232                                         outb(tmp, EWRK3_DATA);
1233                                 } else {
1234                                         writeb(readb(lp->mctbl + byte) | bit, lp->mctbl + byte);
1235                                 }
1236                         }
1237                 }
1238         }
1239
1240         spin_unlock_irq(&lp->hw_lock);
1241 }
1242
1243 /*
1244    ** ISA bus I/O device probe
1245  */
1246 static int __init isa_probe(struct net_device *dev, u_long ioaddr)
1247 {
1248         int i = num_ewrks3s, maxSlots;
1249         int ret = -ENODEV;
1250
1251         u_long iobase;
1252
1253         if (ioaddr >= 0x400)
1254                 goto out;
1255
1256         if (ioaddr == 0) {      /* Autoprobing */
1257                 iobase = EWRK3_IO_BASE;         /* Get the first slot address */
1258                 maxSlots = 24;
1259         } else {                /* Probe a specific location */
1260                 iobase = ioaddr;
1261                 maxSlots = i + 1;
1262         }
1263
1264         for (; (i < maxSlots) && (dev != NULL);
1265              iobase += EWRK3_IOP_INC, i++)
1266         {
1267                 if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME)) {
1268                         if (DevicePresent(iobase) == 0) {
1269                                 int irq = dev->irq;
1270                                 ret = ewrk3_hw_init(dev, iobase);
1271                                 if (!ret)
1272                                         break;
1273                                 dev->irq = irq;
1274                         }
1275                         release_region(iobase, EWRK3_TOTAL_SIZE);
1276                 }
1277         }
1278  out:
1279
1280         return ret;
1281 }
1282
1283 /*
1284    ** EISA bus I/O device probe. Probe from slot 1 since slot 0 is usually
1285    ** the motherboard.
1286  */
1287 static int __init eisa_probe(struct net_device *dev, u_long ioaddr)
1288 {
1289         int i, maxSlots;
1290         u_long iobase;
1291         int ret = -ENODEV;
1292
1293         if (ioaddr < 0x1000)
1294                 goto out;
1295
1296         iobase = ioaddr;
1297         i = (ioaddr >> 12);
1298         maxSlots = i + 1;
1299
1300         for (i = 1; (i < maxSlots) && (dev != NULL); i++, iobase += EISA_SLOT_INC) {
1301                 if (EISA_signature(name, EISA_ID) == 0) {
1302                         if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME) &&
1303                             DevicePresent(iobase) == 0) {
1304                                 int irq = dev->irq;
1305                                 ret = ewrk3_hw_init(dev, iobase);
1306                                 if (!ret)
1307                                         break;
1308                                 dev->irq = irq;
1309                         }
1310                         release_region(iobase, EWRK3_TOTAL_SIZE);
1311                 }
1312         }
1313
1314  out:
1315         return ret;
1316 }
1317
1318
1319 /*
1320    ** Read the EWRK3 EEPROM using this routine
1321  */
1322 static int Read_EEPROM(u_long iobase, u_char eaddr)
1323 {
1324         int i;
1325
1326         outb((eaddr & 0x3f), EWRK3_PIR1);       /* set up 6 bits of address info */
1327         outb(EEPROM_RD, EWRK3_IOPR);    /* issue read command */
1328         for (i = 0; i < 5000; i++)
1329                 inb(EWRK3_CSR); /* wait 1msec */
1330
1331         return inw(EWRK3_EPROM1);       /* 16 bits data return */
1332 }
1333
1334 /*
1335    ** Write the EWRK3 EEPROM using this routine
1336  */
1337 static int Write_EEPROM(short data, u_long iobase, u_char eaddr)
1338 {
1339         int i;
1340
1341         outb(EEPROM_WR_EN, EWRK3_IOPR);         /* issue write enable command */
1342         for (i = 0; i < 5000; i++)
1343                 inb(EWRK3_CSR); /* wait 1msec */
1344         outw(data, EWRK3_EPROM1);       /* write data to register */
1345         outb((eaddr & 0x3f), EWRK3_PIR1);       /* set up 6 bits of address info */
1346         outb(EEPROM_WR, EWRK3_IOPR);    /* issue write command */
1347         for (i = 0; i < 75000; i++)
1348                 inb(EWRK3_CSR); /* wait 15msec */
1349         outb(EEPROM_WR_DIS, EWRK3_IOPR);        /* issue write disable command */
1350         for (i = 0; i < 5000; i++)
1351                 inb(EWRK3_CSR); /* wait 1msec */
1352
1353         return 0;
1354 }
1355
1356 /*
1357    ** Look for a particular board name in the on-board EEPROM.
1358  */
1359 static void __init EthwrkSignature(char *name, char *eeprom_image)
1360 {
1361         int i;
1362         char *signatures[] = EWRK3_SIGNATURE;
1363
1364         for (i=0; *signatures[i] != '\0'; i++)
1365                 if( !strncmp(eeprom_image+EEPROM_PNAME7, signatures[i], strlen(signatures[i])) )
1366                         break;
1367
1368         if (*signatures[i] != '\0') {
1369                 memcpy(name, eeprom_image+EEPROM_PNAME7, EWRK3_STRLEN);
1370                 name[EWRK3_STRLEN] = '\0';
1371         } else
1372                 name[0] = '\0';
1373
1374         return;
1375 }
1376
1377 /*
1378    ** Look for a special sequence in the Ethernet station address PROM that
1379    ** is common across all EWRK3 products.
1380    **
1381    ** Search the Ethernet address ROM for the signature. Since the ROM address
1382    ** counter can start at an arbitrary point, the search must include the entire
1383    ** probe sequence length plus the (length_of_the_signature - 1).
1384    ** Stop the search IMMEDIATELY after the signature is found so that the
1385    ** PROM address counter is correctly positioned at the start of the
1386    ** ethernet address for later read out.
1387  */
1388
1389 static int __init DevicePresent(u_long iobase)
1390 {
1391         union {
1392                 struct {
1393                         u32 a;
1394                         u32 b;
1395                 } llsig;
1396                 char Sig[sizeof(u32) << 1];
1397         }
1398         dev;
1399         short sigLength;
1400         char data;
1401         int i, j, status = 0;
1402
1403         dev.llsig.a = ETH_PROM_SIG;
1404         dev.llsig.b = ETH_PROM_SIG;
1405         sigLength = sizeof(u32) << 1;
1406
1407         for (i = 0, j = 0; j < sigLength && i < PROBE_LENGTH + sigLength - 1; i++) {
1408                 data = inb(EWRK3_APROM);
1409                 if (dev.Sig[j] == data) {       /* track signature */
1410                         j++;
1411                 } else {        /* lost signature; begin search again */
1412                         if (data == dev.Sig[0]) {
1413                                 j = 1;
1414                         } else {
1415                                 j = 0;
1416                         }
1417                 }
1418         }
1419
1420         if (j != sigLength) {
1421                 status = -ENODEV;       /* search failed */
1422         }
1423         return status;
1424 }
1425
1426 static u_char __init get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType)
1427 {
1428         int i, j, k;
1429         u_short chksum;
1430         u_char crc, lfsr, sd, status = 0;
1431         u_long iobase = dev->base_addr;
1432         u16 tmp;
1433
1434         if (chipType == LeMAC2) {
1435                 for (crc = 0x6a, j = 0; j < ETH_ALEN; j++) {
1436                         sd = dev->dev_addr[j] = eeprom_image[EEPROM_PADDR0 + j];
1437                         outb(dev->dev_addr[j], EWRK3_PAR0 + j);
1438                         for (k = 0; k < 8; k++, sd >>= 1) {
1439                                 lfsr = ((((crc & 0x02) >> 1) ^ (crc & 0x01)) ^ (sd & 0x01)) << 7;
1440                                 crc = (crc >> 1) + lfsr;
1441                         }
1442                 }
1443                 if (crc != eeprom_image[EEPROM_PA_CRC])
1444                         status = -1;
1445         } else {
1446                 for (i = 0, k = 0; i < ETH_ALEN;) {
1447                         k <<= 1;
1448                         if (k > 0xffff)
1449                                 k -= 0xffff;
1450
1451                         k += (u_char) (tmp = inb(EWRK3_APROM));
1452                         dev->dev_addr[i] = (u_char) tmp;
1453                         outb(dev->dev_addr[i], EWRK3_PAR0 + i);
1454                         i++;
1455                         k += (u_short) ((tmp = inb(EWRK3_APROM)) << 8);
1456                         dev->dev_addr[i] = (u_char) tmp;
1457                         outb(dev->dev_addr[i], EWRK3_PAR0 + i);
1458                         i++;
1459
1460                         if (k > 0xffff)
1461                                 k -= 0xffff;
1462                 }
1463                 if (k == 0xffff)
1464                         k = 0;
1465                 chksum = inb(EWRK3_APROM);
1466                 chksum |= (inb(EWRK3_APROM) << 8);
1467                 if (k != chksum)
1468                         status = -1;
1469         }
1470
1471         return status;
1472 }
1473
1474 /*
1475    ** Look for a particular board name in the EISA configuration space
1476  */
1477 static int __init EISA_signature(char *name, s32 eisa_id)
1478 {
1479         u_long i;
1480         char *signatures[] = EWRK3_SIGNATURE;
1481         char ManCode[EWRK3_STRLEN];
1482         union {
1483                 s32 ID;
1484                 char Id[4];
1485         } Eisa;
1486         int status = 0;
1487
1488         *name = '\0';
1489         for (i = 0; i < 4; i++) {
1490                 Eisa.Id[i] = inb(eisa_id + i);
1491         }
1492
1493         ManCode[0] = (((Eisa.Id[0] >> 2) & 0x1f) + 0x40);
1494         ManCode[1] = (((Eisa.Id[1] & 0xe0) >> 5) + ((Eisa.Id[0] & 0x03) << 3) + 0x40);
1495         ManCode[2] = (((Eisa.Id[2] >> 4) & 0x0f) + 0x30);
1496         ManCode[3] = ((Eisa.Id[2] & 0x0f) + 0x30);
1497         ManCode[4] = (((Eisa.Id[3] >> 4) & 0x0f) + 0x30);
1498         ManCode[5] = '\0';
1499
1500         for (i = 0; (*signatures[i] != '\0') && (*name == '\0'); i++) {
1501                 if (strstr(ManCode, signatures[i]) != NULL) {
1502                         strcpy(name, ManCode);
1503                         status = 1;
1504                 }
1505         }
1506
1507         return status;          /* return the device name string */
1508 }
1509
1510 static void ewrk3_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
1511 {
1512         int fwrev = Read_EEPROM(dev->base_addr, EEPROM_REVLVL);
1513
1514         strcpy(info->driver, DRV_NAME);
1515         strcpy(info->version, DRV_VERSION);
1516         sprintf(info->fw_version, "%d", fwrev);
1517         strcpy(info->bus_info, "N/A");
1518         info->eedump_len = EEPROM_MAX;
1519 }
1520
1521 static int ewrk3_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
1522 {
1523         struct ewrk3_private *lp = netdev_priv(dev);
1524         unsigned long iobase = dev->base_addr;
1525         u8 cr = inb(EWRK3_CR);
1526
1527         switch (lp->adapter_name[4]) {
1528         case '3': /* DE203 */
1529                 ecmd->supported = SUPPORTED_BNC;
1530                 ecmd->port = PORT_BNC;
1531                 break;
1532
1533         case '4': /* DE204 */
1534                 ecmd->supported = SUPPORTED_TP;
1535                 ecmd->port = PORT_TP;
1536                 break;
1537
1538         case '5': /* DE205 */
1539                 ecmd->supported = SUPPORTED_TP | SUPPORTED_BNC | SUPPORTED_AUI;
1540                 ecmd->autoneg = !(cr & CR_APD);
1541                 /*
1542                 ** Port is only valid if autoneg is disabled
1543                 ** and even then we don't know if AUI is jumpered.
1544                 */
1545                 if (!ecmd->autoneg)
1546                         ecmd->port = (cr & CR_PSEL) ? PORT_BNC : PORT_TP;
1547                 break;
1548         }
1549
1550         ecmd->supported |= SUPPORTED_10baseT_Half;
1551         ecmd->speed = SPEED_10;
1552         ecmd->duplex = DUPLEX_HALF;
1553         return 0;
1554 }
1555
1556 static int ewrk3_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
1557 {
1558         struct ewrk3_private *lp = netdev_priv(dev);
1559         unsigned long iobase = dev->base_addr;
1560         unsigned long flags;
1561         u8 cr;
1562
1563         /* DE205 is the only card with anything to set */
1564         if (lp->adapter_name[4] != '5')
1565                 return -EOPNOTSUPP;
1566
1567         /* Sanity-check parameters */
1568         if (ecmd->speed != SPEED_10)
1569                 return -EINVAL;
1570         if (ecmd->port != PORT_TP && ecmd->port != PORT_BNC)
1571                 return -EINVAL; /* AUI is not software-selectable */
1572         if (ecmd->transceiver != XCVR_INTERNAL)
1573                 return -EINVAL;
1574         if (ecmd->duplex != DUPLEX_HALF)
1575                 return -EINVAL;
1576         if (ecmd->phy_address != 0)
1577                 return -EINVAL;
1578
1579         spin_lock_irqsave(&lp->hw_lock, flags);
1580         cr = inb(EWRK3_CR);
1581
1582         /* If Autoneg is set, change to Auto Port mode */
1583         /* Otherwise, disable Auto Port and set port explicitly */
1584         if (ecmd->autoneg) {
1585                 cr &= ~CR_APD;
1586         } else {
1587                 cr |= CR_APD;
1588                 if (ecmd->port == PORT_TP)
1589                         cr &= ~CR_PSEL;         /* Force TP */
1590                 else
1591                         cr |= CR_PSEL;          /* Force BNC */
1592         }
1593
1594         /* Commit the changes */
1595         outb(cr, EWRK3_CR);
1596         spin_unlock_irqrestore(&lp->hw_lock, flags);
1597         return 0;
1598 }
1599
1600 static u32 ewrk3_get_link(struct net_device *dev)
1601 {
1602         unsigned long iobase = dev->base_addr;
1603         u8 cmr = inb(EWRK3_CMR);
1604         /* DE203 has BNC only and link status does not apply */
1605         /* On DE204 this is always valid since TP is the only port. */
1606         /* On DE205 this reflects TP status even if BNC or AUI is selected. */
1607         return !(cmr & CMR_LINK);
1608 }
1609
1610 static int ewrk3_phys_id(struct net_device *dev, u32 data)
1611 {
1612         struct ewrk3_private *lp = netdev_priv(dev);
1613         unsigned long iobase = dev->base_addr;
1614         unsigned long flags;
1615         u8 cr;
1616         int count;
1617
1618         /* Toggle LED 4x per second */
1619         count = data << 2;
1620
1621         spin_lock_irqsave(&lp->hw_lock, flags);
1622
1623         /* Bail if a PHYS_ID is already in progress */
1624         if (lp->led_mask == 0) {
1625                 spin_unlock_irqrestore(&lp->hw_lock, flags);
1626                 return -EBUSY;
1627         }
1628
1629         /* Prevent ISR from twiddling the LED */
1630         lp->led_mask = 0;
1631
1632         while (count--) {
1633                 /* Toggle the LED */
1634                 cr = inb(EWRK3_CR);
1635                 outb(cr ^ CR_LED, EWRK3_CR);
1636
1637                 /* Wait a little while */
1638                 spin_unlock_irqrestore(&lp->hw_lock, flags);
1639                 msleep(250);
1640                 spin_lock_irqsave(&lp->hw_lock, flags);
1641
1642                 /* Exit if we got a signal */
1643                 if (signal_pending(current))
1644                         break;
1645         }
1646
1647         lp->led_mask = CR_LED;
1648         cr = inb(EWRK3_CR);
1649         outb(cr & ~CR_LED, EWRK3_CR);
1650         spin_unlock_irqrestore(&lp->hw_lock, flags);
1651         return signal_pending(current) ? -ERESTARTSYS : 0;
1652 }
1653
1654 static const struct ethtool_ops ethtool_ops_203 = {
1655         .get_drvinfo = ewrk3_get_drvinfo,
1656         .get_settings = ewrk3_get_settings,
1657         .set_settings = ewrk3_set_settings,
1658         .phys_id = ewrk3_phys_id,
1659 };
1660
1661 static const struct ethtool_ops ethtool_ops = {
1662         .get_drvinfo = ewrk3_get_drvinfo,
1663         .get_settings = ewrk3_get_settings,
1664         .set_settings = ewrk3_set_settings,
1665         .get_link = ewrk3_get_link,
1666         .phys_id = ewrk3_phys_id,
1667 };
1668
1669 /*
1670    ** Perform IOCTL call functions here. Some are privileged operations and the
1671    ** effective uid is checked in those cases.
1672  */
1673 static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
1674 {
1675         struct ewrk3_private *lp = netdev_priv(dev);
1676         struct ewrk3_ioctl *ioc = (struct ewrk3_ioctl *) &rq->ifr_ifru;
1677         u_long iobase = dev->base_addr;
1678         int i, j, status = 0;
1679         u_char csr;
1680         unsigned long flags;
1681         union ewrk3_addr {
1682                 u_char addr[HASH_TABLE_LEN * ETH_ALEN];
1683                 u_short val[(HASH_TABLE_LEN * ETH_ALEN) >> 1];
1684         };
1685
1686         union ewrk3_addr *tmp;
1687
1688         /* All we handle are private IOCTLs */
1689         if (cmd != EWRK3IOCTL)
1690                 return -EOPNOTSUPP;
1691
1692         tmp = kmalloc(sizeof(union ewrk3_addr), GFP_KERNEL);
1693         if(tmp==NULL)
1694                 return -ENOMEM;
1695
1696         switch (ioc->cmd) {
1697         case EWRK3_GET_HWADDR:  /* Get the hardware address */
1698                 for (i = 0; i < ETH_ALEN; i++) {
1699                         tmp->addr[i] = dev->dev_addr[i];
1700                 }
1701                 ioc->len = ETH_ALEN;
1702                 if (copy_to_user(ioc->data, tmp->addr, ioc->len))
1703                         status = -EFAULT;
1704                 break;
1705
1706         case EWRK3_SET_HWADDR:  /* Set the hardware address */
1707                 if (capable(CAP_NET_ADMIN)) {
1708                         spin_lock_irqsave(&lp->hw_lock, flags);
1709                         csr = inb(EWRK3_CSR);
1710                         csr |= (CSR_TXD | CSR_RXD);
1711                         outb(csr, EWRK3_CSR);   /* Disable the TX and RX */
1712                         spin_unlock_irqrestore(&lp->hw_lock, flags);
1713
1714                         if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN)) {
1715                                 status = -EFAULT;
1716                                 break;
1717                         }
1718                         spin_lock_irqsave(&lp->hw_lock, flags);
1719                         for (i = 0; i < ETH_ALEN; i++) {
1720                                 dev->dev_addr[i] = tmp->addr[i];
1721                                 outb(tmp->addr[i], EWRK3_PAR0 + i);
1722                         }
1723
1724                         csr = inb(EWRK3_CSR);
1725                         csr &= ~(CSR_TXD | CSR_RXD);    /* Enable the TX and RX */
1726                         outb(csr, EWRK3_CSR);
1727                         spin_unlock_irqrestore(&lp->hw_lock, flags);
1728                 } else {
1729                         status = -EPERM;
1730                 }
1731
1732                 break;
1733         case EWRK3_SET_PROM:    /* Set Promiscuous Mode */
1734                 if (capable(CAP_NET_ADMIN)) {
1735                         spin_lock_irqsave(&lp->hw_lock, flags);
1736                         csr = inb(EWRK3_CSR);
1737                         csr |= CSR_PME;
1738                         csr &= ~CSR_MCE;
1739                         outb(csr, EWRK3_CSR);
1740                         spin_unlock_irqrestore(&lp->hw_lock, flags);
1741                 } else {
1742                         status = -EPERM;
1743                 }
1744
1745                 break;
1746         case EWRK3_CLR_PROM:    /* Clear Promiscuous Mode */
1747                 if (capable(CAP_NET_ADMIN)) {
1748                         spin_lock_irqsave(&lp->hw_lock, flags);
1749                         csr = inb(EWRK3_CSR);
1750                         csr &= ~CSR_PME;
1751                         outb(csr, EWRK3_CSR);
1752                         spin_unlock_irqrestore(&lp->hw_lock, flags);
1753                 } else {
1754                         status = -EPERM;
1755                 }
1756
1757                 break;
1758         case EWRK3_GET_MCA:     /* Get the multicast address table */
1759                 spin_lock_irqsave(&lp->hw_lock, flags);
1760                 if (lp->shmem_length == IO_ONLY) {
1761                         outb(0, EWRK3_IOPR);
1762                         outw(PAGE0_HTE, EWRK3_PIR1);
1763                         for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
1764                                 tmp->addr[i] = inb(EWRK3_DATA);
1765                         }
1766                 } else {
1767                         outb(0, EWRK3_MPR);
1768                         memcpy_fromio(tmp->addr, lp->shmem + PAGE0_HTE, (HASH_TABLE_LEN >> 3));
1769                 }
1770                 spin_unlock_irqrestore(&lp->hw_lock, flags);
1771
1772                 ioc->len = (HASH_TABLE_LEN >> 3);
1773                 if (copy_to_user(ioc->data, tmp->addr, ioc->len))
1774                         status = -EFAULT;
1775
1776                 break;
1777         case EWRK3_SET_MCA:     /* Set a multicast address */
1778                 if (capable(CAP_NET_ADMIN)) {
1779                         if (ioc->len > 1024)
1780                         {
1781                                 status = -EINVAL;
1782                                 break;
1783                         }
1784                         if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN * ioc->len)) {
1785                                 status = -EFAULT;
1786                                 break;
1787                         }
1788                         set_multicast_list(dev);
1789                 } else {
1790                         status = -EPERM;
1791                 }
1792
1793                 break;
1794         case EWRK3_CLR_MCA:     /* Clear all multicast addresses */
1795                 if (capable(CAP_NET_ADMIN)) {
1796                         set_multicast_list(dev);
1797                 } else {
1798                         status = -EPERM;
1799                 }
1800
1801                 break;
1802         case EWRK3_MCA_EN:      /* Enable multicast addressing */
1803                 if (capable(CAP_NET_ADMIN)) {
1804                         spin_lock_irqsave(&lp->hw_lock, flags);
1805                         csr = inb(EWRK3_CSR);
1806                         csr |= CSR_MCE;
1807                         csr &= ~CSR_PME;
1808                         outb(csr, EWRK3_CSR);
1809                         spin_unlock_irqrestore(&lp->hw_lock, flags);
1810                 } else {
1811                         status = -EPERM;
1812                 }
1813
1814                 break;
1815         case EWRK3_GET_STATS: { /* Get the driver statistics */
1816                 struct ewrk3_stats *tmp_stats =
1817                         kmalloc(sizeof(lp->pktStats), GFP_KERNEL);
1818                 if (!tmp_stats) {
1819                         status = -ENOMEM;
1820                         break;
1821                 }
1822
1823                 spin_lock_irqsave(&lp->hw_lock, flags);
1824                 memcpy(tmp_stats, &lp->pktStats, sizeof(lp->pktStats));
1825                 spin_unlock_irqrestore(&lp->hw_lock, flags);
1826
1827                 ioc->len = sizeof(lp->pktStats);
1828                 if (copy_to_user(ioc->data, tmp_stats, sizeof(lp->pktStats)))
1829                         status = -EFAULT;
1830                 kfree(tmp_stats);
1831                 break;
1832         }
1833         case EWRK3_CLR_STATS:   /* Zero out the driver statistics */
1834                 if (capable(CAP_NET_ADMIN)) {
1835                         spin_lock_irqsave(&lp->hw_lock, flags);
1836                         memset(&lp->pktStats, 0, sizeof(lp->pktStats));
1837                         spin_unlock_irqrestore(&lp->hw_lock,flags);
1838                 } else {
1839                         status = -EPERM;
1840                 }
1841
1842                 break;
1843         case EWRK3_GET_CSR:     /* Get the CSR Register contents */
1844                 tmp->addr[0] = inb(EWRK3_CSR);
1845                 ioc->len = 1;
1846                 if (copy_to_user(ioc->data, tmp->addr, ioc->len))
1847                         status = -EFAULT;
1848                 break;
1849         case EWRK3_SET_CSR:     /* Set the CSR Register contents */
1850                 if (capable(CAP_NET_ADMIN)) {
1851                         if (copy_from_user(tmp->addr, ioc->data, 1)) {
1852                                 status = -EFAULT;
1853                                 break;
1854                         }
1855                         outb(tmp->addr[0], EWRK3_CSR);
1856                 } else {
1857                         status = -EPERM;
1858                 }
1859
1860                 break;
1861         case EWRK3_GET_EEPROM:  /* Get the EEPROM contents */
1862                 if (capable(CAP_NET_ADMIN)) {
1863                         for (i = 0; i < (EEPROM_MAX >> 1); i++) {
1864                                 tmp->val[i] = (short) Read_EEPROM(iobase, i);
1865                         }
1866                         i = EEPROM_MAX;
1867                         tmp->addr[i++] = inb(EWRK3_CMR);                /* Config/Management Reg. */
1868                         for (j = 0; j < ETH_ALEN; j++) {
1869                                 tmp->addr[i++] = inb(EWRK3_PAR0 + j);
1870                         }
1871                         ioc->len = EEPROM_MAX + 1 + ETH_ALEN;
1872                         if (copy_to_user(ioc->data, tmp->addr, ioc->len))
1873                                 status = -EFAULT;
1874                 } else {
1875                         status = -EPERM;
1876                 }
1877
1878                 break;
1879         case EWRK3_SET_EEPROM:  /* Set the EEPROM contents */
1880                 if (capable(CAP_NET_ADMIN)) {
1881                         if (copy_from_user(tmp->addr, ioc->data, EEPROM_MAX)) {
1882                                 status = -EFAULT;
1883                                 break;
1884                         }
1885                         for (i = 0; i < (EEPROM_MAX >> 1); i++) {
1886                                 Write_EEPROM(tmp->val[i], iobase, i);
1887                         }
1888                 } else {
1889                         status = -EPERM;
1890                 }
1891
1892                 break;
1893         case EWRK3_GET_CMR:     /* Get the CMR Register contents */
1894                 tmp->addr[0] = inb(EWRK3_CMR);
1895                 ioc->len = 1;
1896                 if (copy_to_user(ioc->data, tmp->addr, ioc->len))
1897                         status = -EFAULT;
1898                 break;
1899         case EWRK3_SET_TX_CUT_THRU:     /* Set TX cut through mode */
1900                 if (capable(CAP_NET_ADMIN)) {
1901                         lp->txc = 1;
1902                 } else {
1903                         status = -EPERM;
1904                 }
1905
1906                 break;
1907         case EWRK3_CLR_TX_CUT_THRU:     /* Clear TX cut through mode */
1908                 if (capable(CAP_NET_ADMIN)) {
1909                         lp->txc = 0;
1910                 } else {
1911                         status = -EPERM;
1912                 }
1913
1914                 break;
1915         default:
1916                 status = -EOPNOTSUPP;
1917         }
1918         kfree(tmp);
1919         return status;
1920 }
1921
1922 #ifdef MODULE
1923 static struct net_device *ewrk3_devs[MAX_NUM_EWRK3S];
1924 static int ndevs;
1925 static int io[MAX_NUM_EWRK3S+1] = { 0x300, 0, };
1926
1927 /* '21' below should really be 'MAX_NUM_EWRK3S' */
1928 module_param_array(io, int, NULL, 0);
1929 module_param_array(irq, int, NULL, 0);
1930 MODULE_PARM_DESC(io, "EtherWORKS 3 I/O base address(es)");
1931 MODULE_PARM_DESC(irq, "EtherWORKS 3 IRQ number(s)");
1932
1933 static __exit void ewrk3_exit_module(void)
1934 {
1935         int i;
1936
1937         for( i=0; i<ndevs; i++ ) {
1938                 struct net_device *dev = ewrk3_devs[i];
1939                 struct ewrk3_private *lp = netdev_priv(dev);
1940                 ewrk3_devs[i] = NULL;
1941                 unregister_netdev(dev);
1942                 release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
1943                 iounmap(lp->shmem);
1944                 free_netdev(dev);
1945         }
1946 }
1947
1948 static __init int ewrk3_init_module(void)
1949 {
1950         int i=0;
1951
1952         while( io[i] && irq[i] ) {
1953                 struct net_device *dev
1954                         = alloc_etherdev(sizeof(struct ewrk3_private));
1955
1956                 if (!dev)
1957                         break;
1958
1959                 if (ewrk3_probe1(dev, io[i], irq[i]) != 0) {
1960                         free_netdev(dev);
1961                         break;
1962                 }
1963
1964                 ewrk3_devs[ndevs++] = dev;
1965                 i++;
1966         }
1967
1968         return ndevs ? 0 : -EIO;
1969 }
1970
1971
1972 /* Hack for breakage in new module stuff */
1973 module_exit(ewrk3_exit_module);
1974 module_init(ewrk3_init_module);
1975 #endif                          /* MODULE */
1976 MODULE_LICENSE("GPL");