SAFE public projects git trees. - safe/jmp/linux-2.6/blob - arch/blackfin/mach-bf538/boards/ezkit.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *                2005 National ICT Australia (NICTA)
   4  *                      Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Licensed under the GPL-2
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/platform_device.h>
  11 #include <linux/mtd/mtd.h>
  12 #include <linux/mtd/physmap.h>
  13 #include <linux/mtd/partitions.h>
  14 #include <linux/spi/spi.h>
  15 #include <linux/spi/flash.h>
  16 #include <linux/irq.h>
  17 #include <linux/interrupt.h>
  18 #include <asm/bfin5xx_spi.h>
  19 #include <asm/dma.h>
  20 #include <asm/gpio.h>
  21 #include <asm/nand.h>
  22 #include <asm/portmux.h>
  23 #include <asm/dpmc.h>
  24 #include <linux/input.h>
  25
  26 /*
  27  * Name the Board for the /proc/cpuinfo
  28  */
  29 const char bfin_board_name[] = "ADI BF538-EZKIT";
  30
  31 /*
  32  *  Driver needs to know address, irq and flag pin.
  33  */
  34
  35
  36 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
  37 static struct platform_device rtc_device = {
  38         .name = "rtc-bfin",
  39         .id   = -1,
  40 };
  41 #endif
  42
  43 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
  44 static struct resource bfin_uart_resources[] = {
  45 #ifdef CONFIG_SERIAL_BFIN_UART0
  46         {
  47                 .start = 0xFFC00400,
  48                 .end = 0xFFC004FF,
  49                 .flags = IORESOURCE_MEM,
  50         },
  51 #endif
  52 #ifdef CONFIG_SERIAL_BFIN_UART1
  53         {
  54                 .start = 0xFFC02000,
  55                 .end = 0xFFC020FF,
  56                 .flags = IORESOURCE_MEM,
  57         },
  58 #endif
  59 #ifdef CONFIG_SERIAL_BFIN_UART2
  60         {
  61                 .start = 0xFFC02100,
  62                 .end = 0xFFC021FF,
  63                 .flags = IORESOURCE_MEM,
  64         },
  65 #endif
  66 };
  67
  68 static struct platform_device bfin_uart_device = {
  69         .name = "bfin-uart",
  70         .id = 1,
  71         .num_resources = ARRAY_SIZE(bfin_uart_resources),
  72         .resource = bfin_uart_resources,
  73 };
  74 #endif
  75
  76 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
  77 #ifdef CONFIG_BFIN_SIR0
  78 static struct resource bfin_sir0_resources[] = {
  79         {
  80                 .start = 0xFFC00400,
  81                 .end = 0xFFC004FF,
  82                 .flags = IORESOURCE_MEM,
  83         },
  84         {
  85                 .start = IRQ_UART0_RX,
  86                 .end = IRQ_UART0_RX+1,
  87                 .flags = IORESOURCE_IRQ,
  88         },
  89         {
  90                 .start = CH_UART0_RX,
  91                 .end = CH_UART0_RX+1,
  92                 .flags = IORESOURCE_DMA,
  93         },
  94 };
  95 static struct platform_device bfin_sir0_device = {
  96         .name = "bfin_sir",
  97         .id = 0,
  98         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
  99         .resource = bfin_sir0_resources,
 100 };
 101 #endif
 102 #ifdef CONFIG_BFIN_SIR1
 103 static struct resource bfin_sir1_resources[] = {
 104         {
 105                 .start = 0xFFC02000,
 106                 .end = 0xFFC020FF,
 107                 .flags = IORESOURCE_MEM,
 108         },
 109         {
 110                 .start = IRQ_UART1_RX,
 111                 .end = IRQ_UART1_RX+1,
 112                 .flags = IORESOURCE_IRQ,
 113         },
 114         {
 115                 .start = CH_UART1_RX,
 116                 .end = CH_UART1_RX+1,
 117                 .flags = IORESOURCE_DMA,
 118         },
 119 };
 120 static struct platform_device bfin_sir1_device = {
 121         .name = "bfin_sir",
 122         .id = 1,
 123         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 124         .resource = bfin_sir1_resources,
 125 };
 126 #endif
 127 #ifdef CONFIG_BFIN_SIR2
 128 static struct resource bfin_sir2_resources[] = {
 129         {
 130                 .start = 0xFFC02100,
 131                 .end = 0xFFC021FF,
 132                 .flags = IORESOURCE_MEM,
 133         },
 134         {
 135                 .start = IRQ_UART2_RX,
 136                 .end = IRQ_UART2_RX+1,
 137                 .flags = IORESOURCE_IRQ,
 138         },
 139         {
 140                 .start = CH_UART2_RX,
 141                 .end = CH_UART2_RX+1,
 142                 .flags = IORESOURCE_DMA,
 143         },
 144 };
 145 static struct platform_device bfin_sir2_device = {
 146         .name = "bfin_sir",
 147         .id = 2,
 148         .num_resources = ARRAY_SIZE(bfin_sir2_resources),
 149         .resource = bfin_sir2_resources,
 150 };
 151 #endif
 152 #endif
 153
 154 /*
 155  *  USB-LAN EzExtender board
 156  *  Driver needs to know address, irq and flag pin.
 157  */
 158 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 159 #include <linux/smc91x.h>
 160
 161 static struct smc91x_platdata smc91x_info = {
 162         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 163         .leda = RPC_LED_100_10,
 164         .ledb = RPC_LED_TX_RX,
 165 };
 166
 167 static struct resource smc91x_resources[] = {
 168         {
 169                 .name = "smc91x-regs",
 170                 .start = 0x20310300,
 171                 .end = 0x20310300 + 16,
 172                 .flags = IORESOURCE_MEM,
 173         }, {
 174                 .start = IRQ_PF0,
 175                 .end = IRQ_PF0,
 176                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 177         },
 178 };
 179 static struct platform_device smc91x_device = {
 180         .name = "smc91x",
 181         .id = 0,
 182         .num_resources = ARRAY_SIZE(smc91x_resources),
 183         .resource = smc91x_resources,
 184         .dev    = {
 185                 .platform_data  = &smc91x_info,
 186         },
 187 };
 188 #endif
 189
 190 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 191 /* all SPI peripherals info goes here */
 192 #if defined(CONFIG_MTD_M25P80) \
 193         || defined(CONFIG_MTD_M25P80_MODULE)
 194 /* SPI flash chip (m25p16) */
 195 static struct mtd_partition bfin_spi_flash_partitions[] = {
 196         {
 197                 .name = "bootloader(spi)",
 198                 .size = 0x00040000,
 199                 .offset = 0,
 200                 .mask_flags = MTD_CAP_ROM
 201         }, {
 202                 .name = "linux kernel(spi)",
 203                 .size = 0x1c0000,
 204                 .offset = 0x40000
 205         }
 206 };
 207
 208 static struct flash_platform_data bfin_spi_flash_data = {
 209         .name = "m25p80",
 210         .parts = bfin_spi_flash_partitions,
 211         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 212         .type = "m25p16",
 213 };
 214
 215 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 216         .enable_dma = 0,         /* use dma transfer with this chip*/
 217         .bits_per_word = 8,
 218         .cs_change_per_word = 0,
 219 };
 220 #endif
 221
 222 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 223 #include <linux/spi/ad7879.h>
 224 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 225         .model                  = 7879, /* Model = AD7879 */
 226         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 227         .pressure_max           = 10000,
 228         .pressure_min           = 0,
 229         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 230         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 231         .median                 = 2,    /* do 8 measurements */
 232         .averaging              = 1,    /* take the average of 4 middle samples */
 233         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 234         .gpio_output            = 1,    /* configure AUX/VBAT/GPIO as GPIO output */
 235         .gpio_default           = 1,    /* During initialization set GPIO = HIGH */
 236 };
 237 #endif
 238
 239 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 240 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 241         .enable_dma = 0,
 242         .bits_per_word = 16,
 243 };
 244 #endif
 245
 246 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 247 #include <asm/bfin-lq035q1.h>
 248
 249 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
 250         .mode =         LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
 251         .use_bl =       0,      /* let something else control the LCD Blacklight */
 252         .gpio_bl =      GPIO_PF7,
 253 };
 254
 255 static struct resource bfin_lq035q1_resources[] = {
 256         {
 257                 .start = IRQ_PPI_ERROR,
 258                 .end = IRQ_PPI_ERROR,
 259                 .flags = IORESOURCE_IRQ,
 260         },
 261 };
 262
 263 static struct platform_device bfin_lq035q1_device = {
 264         .name           = "bfin-lq035q1",
 265         .id             = -1,
 266         .num_resources  = ARRAY_SIZE(bfin_lq035q1_resources),
 267         .resource       = bfin_lq035q1_resources,
 268         .dev            = {
 269                 .platform_data = &bfin_lq035q1_data,
 270         },
 271 };
 272 #endif
 273
 274 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 275 static struct bfin5xx_spi_chip spidev_chip_info = {
 276         .enable_dma = 0,
 277         .bits_per_word = 8,
 278 };
 279 #endif
 280
 281 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 282 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 283         .enable_dma     = 0,
 284         .bits_per_word  = 8,
 285 };
 286 #endif
 287
 288 static struct spi_board_info bf538_spi_board_info[] __initdata = {
 289 #if defined(CONFIG_MTD_M25P80) \
 290         || defined(CONFIG_MTD_M25P80_MODULE)
 291         {
 292                 /* the modalias must be the same as spi device driver name */
 293                 .modalias = "m25p80", /* Name of spi_driver for this device */
 294                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 295                 .bus_num = 0, /* Framework bus number */
 296                 .chip_select = 1, /* SPI_SSEL1*/
 297                 .platform_data = &bfin_spi_flash_data,
 298                 .controller_data = &spi_flash_chip_info,
 299                 .mode = SPI_MODE_3,
 300         },
 301 #endif
 302 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 303         {
 304                 .modalias = "ad7879",
 305                 .platform_data = &bfin_ad7879_ts_info,
 306                 .irq = IRQ_PF3,
 307                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 308                 .bus_num = 0,
 309                 .chip_select = 1,
 310                 .controller_data = &spi_ad7879_chip_info,
 311                 .mode = SPI_CPHA | SPI_CPOL,
 312         },
 313 #endif
 314 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 315         {
 316                 .modalias = "bfin-lq035q1-spi",
 317                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 318                 .bus_num = 0,
 319                 .chip_select = 2,
 320                 .controller_data = &lq035q1_spi_chip_info,
 321                 .mode = SPI_CPHA | SPI_CPOL,
 322         },
 323 #endif
 324 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 325         {
 326                 .modalias = "spidev",
 327                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 328                 .bus_num = 0,
 329                 .chip_select = 1,
 330                 .controller_data = &spidev_chip_info,
 331         },
 332 #endif
 333 };
 334
 335 /* SPI (0) */
 336 static struct resource bfin_spi0_resource[] = {
 337         [0] = {
 338                 .start = SPI0_REGBASE,
 339                 .end   = SPI0_REGBASE + 0xFF,
 340                 .flags = IORESOURCE_MEM,
 341         },
 342         [1] = {
 343                 .start = CH_SPI0,
 344                 .end   = CH_SPI0,
 345                 .flags = IORESOURCE_DMA,
 346         },
 347         [2] = {
 348                 .start = IRQ_SPI0,
 349                 .end   = IRQ_SPI0,
 350                 .flags = IORESOURCE_IRQ,
 351         }
 352 };
 353
 354 /* SPI (1) */
 355 static struct resource bfin_spi1_resource[] = {
 356         [0] = {
 357                 .start = SPI1_REGBASE,
 358                 .end   = SPI1_REGBASE + 0xFF,
 359                 .flags = IORESOURCE_MEM,
 360         },
 361         [1] = {
 362                 .start = CH_SPI1,
 363                 .end   = CH_SPI1,
 364                 .flags = IORESOURCE_DMA,
 365         },
 366         [2] = {
 367                 .start = IRQ_SPI1,
 368                 .end   = IRQ_SPI1,
 369                 .flags = IORESOURCE_IRQ,
 370         }
 371 };
 372
 373 /* SPI (2) */
 374 static struct resource bfin_spi2_resource[] = {
 375         [0] = {
 376                 .start = SPI2_REGBASE,
 377                 .end   = SPI2_REGBASE + 0xFF,
 378                 .flags = IORESOURCE_MEM,
 379         },
 380         [1] = {
 381                 .start = CH_SPI2,
 382                 .end   = CH_SPI2,
 383                 .flags = IORESOURCE_DMA,
 384         },
 385         [2] = {
 386                 .start = IRQ_SPI2,
 387                 .end   = IRQ_SPI2,
 388                 .flags = IORESOURCE_IRQ,
 389         }
 390 };
 391
 392 /* SPI controller data */
 393 static struct bfin5xx_spi_master bf538_spi_master_info0 = {
 394         .num_chipselect = 8,
 395         .enable_dma = 1,  /* master has the ability to do dma transfer */
 396         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 397 };
 398
 399 static struct platform_device bf538_spi_master0 = {
 400         .name = "bfin-spi",
 401         .id = 0, /* Bus number */
 402         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 403         .resource = bfin_spi0_resource,
 404         .dev = {
 405                 .platform_data = &bf538_spi_master_info0, /* Passed to driver */
 406                 },
 407 };
 408
 409 static struct bfin5xx_spi_master bf538_spi_master_info1 = {
 410         .num_chipselect = 8,
 411         .enable_dma = 1,  /* master has the ability to do dma transfer */
 412         .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 413 };
 414
 415 static struct platform_device bf538_spi_master1 = {
 416         .name = "bfin-spi",
 417         .id = 1, /* Bus number */
 418         .num_resources = ARRAY_SIZE(bfin_spi1_resource),
 419         .resource = bfin_spi1_resource,
 420         .dev = {
 421                 .platform_data = &bf538_spi_master_info1, /* Passed to driver */
 422                 },
 423 };
 424
 425 static struct bfin5xx_spi_master bf538_spi_master_info2 = {
 426         .num_chipselect = 8,
 427         .enable_dma = 1,  /* master has the ability to do dma transfer */
 428         .pin_req = {P_SPI2_SCK, P_SPI2_MISO, P_SPI2_MOSI, 0},
 429 };
 430
 431 static struct platform_device bf538_spi_master2 = {
 432         .name = "bfin-spi",
 433         .id = 2, /* Bus number */
 434         .num_resources = ARRAY_SIZE(bfin_spi2_resource),
 435         .resource = bfin_spi2_resource,
 436         .dev = {
 437                 .platform_data = &bf538_spi_master_info2, /* Passed to driver */
 438                 },
 439 };
 440
 441 #endif  /* spi master and devices */
 442
 443 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 444 static struct resource bfin_twi0_resource[] = {
 445         [0] = {
 446                 .start = TWI0_REGBASE,
 447                 .end   = TWI0_REGBASE + 0xFF,
 448                 .flags = IORESOURCE_MEM,
 449         },
 450         [1] = {
 451                 .start = IRQ_TWI0,
 452                 .end   = IRQ_TWI0,
 453                 .flags = IORESOURCE_IRQ,
 454         },
 455 };
 456
 457 static struct platform_device i2c_bfin_twi0_device = {
 458         .name = "i2c-bfin-twi",
 459         .id = 0,
 460         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 461         .resource = bfin_twi0_resource,
 462 };
 463
 464 #if !defined(CONFIG_BF542)      /* The BF542 only has 1 TWI */
 465 static struct resource bfin_twi1_resource[] = {
 466         [0] = {
 467                 .start = TWI1_REGBASE,
 468                 .end   = TWI1_REGBASE + 0xFF,
 469                 .flags = IORESOURCE_MEM,
 470         },
 471         [1] = {
 472                 .start = IRQ_TWI1,
 473                 .end   = IRQ_TWI1,
 474                 .flags = IORESOURCE_IRQ,
 475         },
 476 };
 477
 478 static struct platform_device i2c_bfin_twi1_device = {
 479         .name = "i2c-bfin-twi",
 480         .id = 1,
 481         .num_resources = ARRAY_SIZE(bfin_twi1_resource),
 482         .resource = bfin_twi1_resource,
 483 };
 484 #endif
 485 #endif
 486
 487 static struct resource bfin_gpios_resources = {
 488         .start = 0,
 489         .end   = MAX_BLACKFIN_GPIOS - 1,
 490         .flags = IORESOURCE_IRQ,
 491 };
 492
 493 static struct platform_device bfin_gpios_device = {
 494         .name = "simple-gpio",
 495         .id = -1,
 496         .num_resources = 1,
 497         .resource = &bfin_gpios_resources,
 498 };
 499
 500 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
 501 #include <linux/gpio_keys.h>
 502
 503 static struct gpio_keys_button bfin_gpio_keys_table[] = {
 504         {BTN_0, GPIO_PC7, 1, "gpio-keys: BTN0"},
 505 };
 506
 507 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
 508         .buttons        = bfin_gpio_keys_table,
 509         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
 510 };
 511
 512 static struct platform_device bfin_device_gpiokeys = {
 513         .name      = "gpio-keys",
 514         .dev = {
 515                 .platform_data = &bfin_gpio_keys_data,
 516         },
 517 };
 518 #endif
 519
 520 static const unsigned int cclk_vlev_datasheet[] =
 521 {
 522 /*
 523  * Internal VLEV BF538SBBC1533
 524  ****temporarily using these values until data sheet is updated
 525  */
 526         VRPAIR(VLEV_100, 150000000),
 527         VRPAIR(VLEV_100, 250000000),
 528         VRPAIR(VLEV_110, 276000000),
 529         VRPAIR(VLEV_115, 301000000),
 530         VRPAIR(VLEV_120, 525000000),
 531         VRPAIR(VLEV_125, 550000000),
 532         VRPAIR(VLEV_130, 600000000),
 533 };
 534
 535 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 536         .tuple_tab = cclk_vlev_datasheet,
 537         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 538         .vr_settling_time = 25 /* us */,
 539 };
 540
 541 static struct platform_device bfin_dpmc = {
 542         .name = "bfin dpmc",
 543         .dev = {
 544                 .platform_data = &bfin_dmpc_vreg_data,
 545         },
 546 };
 547
 548 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 549 static struct mtd_partition ezkit_partitions[] = {
 550         {
 551                 .name       = "bootloader(nor)",
 552                 .size       = 0x40000,
 553                 .offset     = 0,
 554         }, {
 555                 .name       = "linux kernel(nor)",
 556                 .size       = 0x180000,
 557                 .offset     = MTDPART_OFS_APPEND,
 558         }, {
 559                 .name       = "file system(nor)",
 560                 .size       = MTDPART_SIZ_FULL,
 561                 .offset     = MTDPART_OFS_APPEND,
 562         }
 563 };
 564
 565 static struct physmap_flash_data ezkit_flash_data = {
 566         .width      = 2,
 567         .parts      = ezkit_partitions,
 568         .nr_parts   = ARRAY_SIZE(ezkit_partitions),
 569 };
 570
 571 static struct resource ezkit_flash_resource = {
 572         .start = 0x20000000,
 573 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 574         .end   = 0x202fffff,
 575 #else
 576         .end   = 0x203fffff,
 577 #endif
 578         .flags = IORESOURCE_MEM,
 579 };
 580
 581 static struct platform_device ezkit_flash_device = {
 582         .name          = "physmap-flash",
 583         .id            = 0,
 584         .dev = {
 585                 .platform_data = &ezkit_flash_data,
 586         },
 587         .num_resources = 1,
 588         .resource      = &ezkit_flash_resource,
 589 };
 590 #endif
 591
 592 static struct platform_device *cm_bf538_devices[] __initdata = {
 593
 594         &bfin_dpmc,
 595
 596 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 597         &rtc_device,
 598 #endif
 599
 600 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 601         &bfin_uart_device,
 602 #endif
 603
 604 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 605         &bf538_spi_master0,
 606         &bf538_spi_master1,
 607         &bf538_spi_master2,
 608 #endif
 609
 610 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 611         &i2c_bfin_twi0_device,
 612         &i2c_bfin_twi1_device,
 613 #endif
 614
 615 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 616 #ifdef CONFIG_BFIN_SIR0
 617         &bfin_sir0_device,
 618 #endif
 619 #ifdef CONFIG_BFIN_SIR1
 620         &bfin_sir1_device,
 621 #endif
 622 #ifdef CONFIG_BFIN_SIR2
 623         &bfin_sir2_device,
 624 #endif
 625 #endif
 626
 627 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 628         &smc91x_device,
 629 #endif
 630
 631 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 632         &bfin_lq035q1_device,
 633 #endif
 634
 635 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
 636         &bfin_device_gpiokeys,
 637 #endif
 638
 639         &bfin_gpios_device,
 640
 641 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 642         &ezkit_flash_device,
 643 #endif
 644 };
 645
 646 static int __init ezkit_init(void)
 647 {
 648         printk(KERN_INFO "%s(): registering device resources\n", __func__);
 649         platform_add_devices(cm_bf538_devices, ARRAY_SIZE(cm_bf538_devices));
 650
 651 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 652         spi_register_board_info(bf538_spi_board_info,
 653                         ARRAY_SIZE(bf538_spi_board_info));
 654 #endif
 655
 656         return 0;
 657 }
 658
 659 arch_initcall(ezkit_init);