#include <mach/board.h>
#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+#include "sam9_smc.h"
#include "generic.h"
/* Initialize processor: 16.367 MHz crystal */
at91sam9263_initialize(16367660);
- /* DGBU on ttyS0. (Rx & Tx only) */
+ /* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
#endif
};
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 1,
+ .ncs_write_setup = 0,
+ .nwe_setup = 1,
+
+ .ncs_read_pulse = 3,
+ .nrd_pulse = 3,
+ .ncs_write_pulse = 3,
+ .nwe_pulse = 3,
+
+ .read_cycle = 5,
+ .write_cycle = 5,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+ .tdf_cycles = 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+ /* setup bus-width (8 or 16) */
+ if (ek_nand_data.bus_width_16)
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+ else
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(3, &ek_nand_smc_config);
+
+ at91_add_device_nand(&ek_nand_data);
+}
+
/*
* I2C devices
.active_low = 1,
.desc = "right_click",
.wakeup = 1,
- },
+ }
};
static struct gpio_keys_platform_data ek_button_data = {
static void __init ek_add_device_buttons(void)
{
- at91_set_GPIO_periph(AT91_PIN_PC5, 0); /* left button */
+ at91_set_GPIO_periph(AT91_PIN_PC5, 1); /* left button */
at91_set_deglitch(AT91_PIN_PC5, 1);
- at91_set_GPIO_periph(AT91_PIN_PC4, 0); /* right button */
+ at91_set_GPIO_periph(AT91_PIN_PC4, 1); /* right button */
at91_set_deglitch(AT91_PIN_PC4, 1);
platform_device_register(&ek_button_device);
/*
* AC97
+ * reset_pin is not connected: NRST
*/
-static struct atmel_ac97_data ek_ac97_data = {
- .reset_pin = AT91_PIN_PA13,
+static struct ac97c_platform_data ek_ac97_data = {
};
}
};
+/*
+ * CAN
+ */
+static void sam9263ek_transceiver_switch(int on)
+{
+ if (on) {
+ at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
+ } else {
+ at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
+ }
+}
+
+static struct at91_can_data ek_can_data = {
+ .transceiver_switch = sam9263ek_transceiver_switch,
+};
static void __init ek_board_init(void)
{
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* NAND */
- at91_add_device_nand(&ek_nand_data);
+ ek_add_device_nand();
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* LCD Controller */
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
+ /* CAN */
+ at91_add_device_can(&ek_can_data);
}
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")