From: Wolfram Sang <w.sang@pengutronix.de>
Date: Mon, 26 Jan 2009 20:19:54 +0000 (+0100)
Subject: spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
X-Git-Tag: v2.6.29-rc3~21^2~3
X-Git-Url: http://ftp.safe.ca/?p=safe%2Fjmp%2Flinux-2.6;a=commitdiff_plain;h=e51d565ff6bb1cedc10568425511badf0633a212

spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
---

diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig
index 3d31b66..5bf3c92 100644
--- a/drivers/misc/eeprom/Kconfig
+++ b/drivers/misc/eeprom/Kconfig
@@ -26,6 +26,17 @@ config AT24
 	  This driver can also be built as a module.  If so, the module
 	  will be called at24.
 
+config SPI_AT25
+	tristate "SPI EEPROMs from most vendors"
+	depends on SPI && SYSFS
+	help
+	  Enable this driver to get read/write support to most SPI EEPROMs,
+	  after you configure the board init code to know about each eeprom
+	  on your target board.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called at25.
+
 config SENSORS_EEPROM
 	tristate "Old I2C EEPROM reader"
 	depends on I2C && EXPERIMENTAL
diff --git a/drivers/misc/eeprom/Makefile b/drivers/misc/eeprom/Makefile
index a3dad28..a4fb5cf 100644
--- a/drivers/misc/eeprom/Makefile
+++ b/drivers/misc/eeprom/Makefile
@@ -1,2 +1,3 @@
 obj-$(CONFIG_AT24)		+= at24.o
+obj-$(CONFIG_SPI_AT25)		+= at25.o
 obj-$(CONFIG_SENSORS_EEPROM)	+= eeprom.o
diff --git a/drivers/spi/at25.c b/drivers/misc/eeprom/at25.c
similarity index 100%
rename from drivers/spi/at25.c
rename to drivers/misc/eeprom/at25.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 4a6fe01..83a185d 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -230,17 +230,6 @@ config SPI_XILINX
 #
 comment "SPI Protocol Masters"
 
-config SPI_AT25
-	tristate "SPI EEPROMs from most vendors"
-	depends on SYSFS
-	help
-	  Enable this driver to get read/write support to most SPI EEPROMs,
-	  after you configure the board init code to know about each eeprom
-	  on your target board.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called at25.
-
 config SPI_SPIDEV
 	tristate "User mode SPI device driver support"
 	depends on EXPERIMENTAL
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 5e9f521..5d04519 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -33,7 +33,6 @@ obj-$(CONFIG_SPI_SH_SCI)		+= spi_sh_sci.o
 # 	... add above this line ...
 
 # SPI protocol drivers (device/link on bus)
-obj-$(CONFIG_SPI_AT25)		+= at25.o
 obj-$(CONFIG_SPI_SPIDEV)	+= spidev.o
 obj-$(CONFIG_SPI_TLE62X0)	+= tle62x0.o
 # 	... add above this line ...