Support for Voiceblue GSM/VoIP gateway. Say Y here if you have
such a board.
-config MACH_NETSTAR
- bool "NetStar"
- depends on ARCH_OMAP1 && ARCH_OMAP15XX
- help
- Support for NetStar PBX. Say Y here if you have such a board.
-
config MACH_OMAP_PALMTE
bool "Palm Tungsten E"
depends on ARCH_OMAP1 && ARCH_OMAP15XX
informations.
Say Y here if you have such a PDA, say NO otherwise.
+config MACH_NOKIA770
+ bool "Nokia 770"
+ depends on ARCH_OMAP1 && ARCH_OMAP16XX
+ help
+ Support for the Nokia 770 Internet Tablet. Say Y here if you
+ have such a device.
+
+config MACH_AMS_DELTA
+ bool "Amstrad E3 (Delta)"
+ depends on ARCH_OMAP1 && ARCH_OMAP15XX
+ help
+ Support for the Amstrad E3 (codename Delta) videophone. Say Y here
+ if you have such a device.
+
config MACH_OMAP_GENERIC
bool "Generic OMAP board"
depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX)
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/board-ams-delta.c
+ *
+ * Modified from board-generic.c
+ *
+ * Board specific inits for the Amstrad E3 (codename Delta) videophone
+ *
+ * Copyright (C) 2006 Jonathan McDowell <noodles@earth.li>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <asm/arch/board-ams-delta.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/usb.h>
+#include <asm/arch/board.h>
+#include <asm/arch/common.h>
+
+static u8 ams_delta_latch1_reg;
+static u16 ams_delta_latch2_reg;
+
+void ams_delta_latch1_write(u8 mask, u8 value)
+{
+ ams_delta_latch1_reg &= ~mask;
+ ams_delta_latch1_reg |= value;
+ *(volatile __u8 *) AMS_DELTA_LATCH1_VIRT = ams_delta_latch1_reg;
+}
+
+void ams_delta_latch2_write(u16 mask, u16 value)
+{
+ ams_delta_latch2_reg &= ~mask;
+ ams_delta_latch2_reg |= value;
+ *(volatile __u16 *) AMS_DELTA_LATCH2_VIRT = ams_delta_latch2_reg;
+}
+
+static void __init ams_delta_init_irq(void)
+{
+ omap1_init_common_hw();
+ omap_init_irq();
+ omap_gpio_init();
+}
+
+static struct map_desc ams_delta_io_desc[] __initdata = {
+ // AMS_DELTA_LATCH1
+ {
+ .virtual = AMS_DELTA_LATCH1_VIRT,
+ .pfn = __phys_to_pfn(AMS_DELTA_LATCH1_PHYS),
+ .length = 0x01000000,
+ .type = MT_DEVICE
+ },
+ // AMS_DELTA_LATCH2
+ {
+ .virtual = AMS_DELTA_LATCH2_VIRT,
+ .pfn = __phys_to_pfn(AMS_DELTA_LATCH2_PHYS),
+ .length = 0x01000000,
+ .type = MT_DEVICE
+ },
+ // AMS_DELTA_MODEM
+ {
+ .virtual = AMS_DELTA_MODEM_VIRT,
+ .pfn = __phys_to_pfn(AMS_DELTA_MODEM_PHYS),
+ .length = 0x01000000,
+ .type = MT_DEVICE
+ }
+};
+
+static struct omap_uart_config ams_delta_uart_config __initdata = {
+ .enabled_uarts = 1,
+};
+
+static struct omap_board_config_kernel ams_delta_config[] = {
+ { OMAP_TAG_UART, &ams_delta_uart_config },
+};
+
+static void __init ams_delta_init(void)
+{
+ iotable_init(ams_delta_io_desc, ARRAY_SIZE(ams_delta_io_desc));
+
+ omap_board_config = ams_delta_config;
+ omap_board_config_size = ARRAY_SIZE(ams_delta_config);
+ omap_serial_init();
+
+ /* Clear latch2 (NAND, LCD, modem enable) */
+ ams_delta_latch2_write(~0, 0);
+}
+
+static void __init ams_delta_map_io(void)
+{
+ omap1_map_common_io();
+}
+
+MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)")
+ /* Maintainer: Jonathan McDowell <noodles@earth.li> */
+ .phys_io = 0xfff00000,
+ .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
+ .boot_params = 0x10000100,
+ .map_io = ams_delta_map_io,
+ .init_irq = ams_delta_init_irq,
+ .init_machine = ams_delta_init,
+ .timer = &omap_timer,
+MACHINE_END
+
+EXPORT_SYMBOL(ams_delta_latch1_write);
+EXPORT_SYMBOL(ams_delta_latch2_write);
static void __init omap_generic_init(void)
{
#ifdef CONFIG_ARCH_OMAP15XX
- if (cpu_is_omap1510()) {
+ if (cpu_is_omap15xx()) {
generic_config[0].data = &generic1510_usb_config;
}
#endif
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
+#include <linux/input.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
+#include <asm/arch/irda.h>
#include <asm/arch/usb.h>
+#include <asm/arch/keypad.h>
#include <asm/arch/common.h>
+#include <asm/arch/mcbsp.h>
+#include <asm/arch/omap-alsa.h>
extern int omap_gpio_init(void);
-static struct mtd_partition h2_partitions[] = {
+static int h2_keymap[] = {
+ KEY(0, 0, KEY_LEFT),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_3),
+ KEY(0, 3, KEY_F10),
+ KEY(0, 4, KEY_F5),
+ KEY(0, 5, KEY_9),
+ KEY(1, 0, KEY_DOWN),
+ KEY(1, 1, KEY_UP),
+ KEY(1, 2, KEY_2),
+ KEY(1, 3, KEY_F9),
+ KEY(1, 4, KEY_F7),
+ KEY(1, 5, KEY_0),
+ KEY(2, 0, KEY_ENTER),
+ KEY(2, 1, KEY_6),
+ KEY(2, 2, KEY_1),
+ KEY(2, 3, KEY_F2),
+ KEY(2, 4, KEY_F6),
+ KEY(2, 5, KEY_HOME),
+ KEY(3, 0, KEY_8),
+ KEY(3, 1, KEY_5),
+ KEY(3, 2, KEY_F12),
+ KEY(3, 3, KEY_F3),
+ KEY(3, 4, KEY_F8),
+ KEY(3, 5, KEY_END),
+ KEY(4, 0, KEY_7),
+ KEY(4, 1, KEY_4),
+ KEY(4, 2, KEY_F11),
+ KEY(4, 3, KEY_F1),
+ KEY(4, 4, KEY_F4),
+ KEY(4, 5, KEY_ESC),
+ KEY(5, 0, KEY_F13),
+ KEY(5, 1, KEY_F14),
+ KEY(5, 2, KEY_F15),
+ KEY(5, 3, KEY_F16),
+ KEY(5, 4, KEY_SLEEP),
+ 0
+};
+
+static struct mtd_partition h2_nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
}
};
-static struct flash_platform_data h2_flash_data = {
+static struct flash_platform_data h2_nor_data = {
.map_name = "cfi_probe",
.width = 2,
- .parts = h2_partitions,
- .nr_parts = ARRAY_SIZE(h2_partitions),
+ .parts = h2_nor_partitions,
+ .nr_parts = ARRAY_SIZE(h2_nor_partitions),
};
-static struct resource h2_flash_resource = {
+static struct resource h2_nor_resource = {
/* This is on CS3, wherever it's mapped */
.flags = IORESOURCE_MEM,
};
-static struct platform_device h2_flash_device = {
+static struct platform_device h2_nor_device = {
.name = "omapflash",
.id = 0,
.dev = {
- .platform_data = &h2_flash_data,
+ .platform_data = &h2_nor_data,
},
.num_resources = 1,
- .resource = &h2_flash_resource,
+ .resource = &h2_nor_resource,
};
static struct resource h2_smc91x_resources[] = {
.resource = h2_smc91x_resources,
};
+static struct resource h2_kp_resources[] = {
+ [0] = {
+ .start = INT_KEYBOARD,
+ .end = INT_KEYBOARD,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct omap_kp_platform_data h2_kp_data = {
+ .rows = 8,
+ .cols = 8,
+ .keymap = h2_keymap,
+ .rep = 1,
+};
+
+static struct platform_device h2_kp_device = {
+ .name = "omap-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &h2_kp_data,
+ },
+ .num_resources = ARRAY_SIZE(h2_kp_resources),
+ .resource = h2_kp_resources,
+};
+
+#define H2_IRDA_FIRSEL_GPIO_PIN 17
+
+#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
+static int h2_transceiver_mode(struct device *dev, int state)
+{
+ if (state & IR_SIRMODE)
+ omap_set_gpio_dataout(H2_IRDA_FIRSEL_GPIO_PIN, 0);
+ else /* MIR/FIR */
+ omap_set_gpio_dataout(H2_IRDA_FIRSEL_GPIO_PIN, 1);
+
+ return 0;
+}
+#endif
+
+static struct omap_irda_config h2_irda_data = {
+ .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
+ .rx_channel = OMAP_DMA_UART3_RX,
+ .tx_channel = OMAP_DMA_UART3_TX,
+ .dest_start = UART3_THR,
+ .src_start = UART3_RHR,
+ .tx_trigger = 0,
+ .rx_trigger = 0,
+};
+
+static struct resource h2_irda_resources[] = {
+ [0] = {
+ .start = INT_UART3,
+ .end = INT_UART3,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+static struct platform_device h2_irda_device = {
+ .name = "omapirda",
+ .id = 0,
+ .dev = {
+ .platform_data = &h2_irda_data,
+ },
+ .num_resources = ARRAY_SIZE(h2_irda_resources),
+ .resource = h2_irda_resources,
+};
+
+static struct platform_device h2_lcd_device = {
+ .name = "lcd_h2",
+ .id = -1,
+};
+
+static struct omap_mcbsp_reg_cfg mcbsp_regs = {
+ .spcr2 = FREE | FRST | GRST | XRST | XINTM(3),
+ .spcr1 = RINTM(3) | RRST,
+ .rcr2 = RPHASE | RFRLEN2(OMAP_MCBSP_WORD_8) |
+ RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(1),
+ .rcr1 = RFRLEN1(OMAP_MCBSP_WORD_8) | RWDLEN1(OMAP_MCBSP_WORD_16),
+ .xcr2 = XPHASE | XFRLEN2(OMAP_MCBSP_WORD_8) |
+ XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(1) | XFIG,
+ .xcr1 = XFRLEN1(OMAP_MCBSP_WORD_8) | XWDLEN1(OMAP_MCBSP_WORD_16),
+ .srgr1 = FWID(15),
+ .srgr2 = GSYNC | CLKSP | FSGM | FPER(31),
+
+ .pcr0 = CLKXM | CLKRM | FSXP | FSRP | CLKXP | CLKRP,
+ //.pcr0 = CLKXP | CLKRP, /* mcbsp: slave */
+};
+
+static struct omap_alsa_codec_config alsa_config = {
+ .name = "H2 TSC2101",
+ .mcbsp_regs_alsa = &mcbsp_regs,
+ .codec_configure_dev = NULL, // tsc2101_configure,
+ .codec_set_samplerate = NULL, // tsc2101_set_samplerate,
+ .codec_clock_setup = NULL, // tsc2101_clock_setup,
+ .codec_clock_on = NULL, // tsc2101_clock_on,
+ .codec_clock_off = NULL, // tsc2101_clock_off,
+ .get_default_samplerate = NULL, // tsc2101_get_default_samplerate,
+};
+
+static struct platform_device h2_mcbsp1_device = {
+ .name = "omap_alsa_mcbsp",
+ .id = 1,
+ .dev = {
+ .platform_data = &alsa_config,
+ },
+};
+
static struct platform_device *h2_devices[] __initdata = {
- &h2_flash_device,
+ &h2_nor_device,
&h2_smc91x_device,
+ &h2_irda_device,
+ &h2_kp_device,
+ &h2_lcd_device,
+ &h2_mcbsp1_device,
};
static void __init h2_init_smc91x(void)
};
static struct omap_lcd_config h2_lcd_config __initdata = {
- .panel_name = "h2",
.ctrl_name = "internal",
};
static void __init h2_init(void)
{
- /* NOTE: revC boards support NAND-boot, which can put NOR on CS2B
- * and NAND (either 16bit or 8bit) on CS3.
+ /* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
+ * to address 0 by a dip switch), NAND on CS2B. The NAND driver will
+ * notice whether a NAND chip is enabled at probe time.
+ *
+ * FIXME revC boards (and H3) support NAND-boot, with a dip switch to
+ * put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
+ * detecting that in code here, to avoid probing every possible flash
+ * configuration...
*/
- h2_flash_resource.end = h2_flash_resource.start = omap_cs3_phys();
- h2_flash_resource.end += SZ_32M - 1;
+ h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
+ h2_nor_resource.end += SZ_32M - 1;
+
+ omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
+ omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* MMC: card detect and WP */
// omap_cfg_reg(U19_ARMIO1); /* CD */
omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
+ /* Irda */
+#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
+ omap_writel(omap_readl(FUNC_MUX_CTRL_A) | 7, FUNC_MUX_CTRL_A);
+ if (!(omap_request_gpio(H2_IRDA_FIRSEL_GPIO_PIN))) {
+ omap_set_gpio_direction(H2_IRDA_FIRSEL_GPIO_PIN, 0);
+ h2_irda_data.transceiver_mode = h2_transceiver_mode;
+ }
+#endif
+
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/errno.h>
+#include <linux/workqueue.h>
#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
+#include <linux/input.h>
#include <asm/setup.h>
#include <asm/page.h>
#include <asm/mach/map.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/gpioexpander.h>
#include <asm/arch/irqs.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
+#include <asm/arch/irda.h>
#include <asm/arch/usb.h>
+#include <asm/arch/keypad.h>
+#include <asm/arch/dma.h>
#include <asm/arch/common.h>
extern int omap_gpio_init(void);
-static struct mtd_partition h3_partitions[] = {
+static int h3_keymap[] = {
+ KEY(0, 0, KEY_LEFT),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_3),
+ KEY(0, 3, KEY_F10),
+ KEY(0, 4, KEY_F5),
+ KEY(0, 5, KEY_9),
+ KEY(1, 0, KEY_DOWN),
+ KEY(1, 1, KEY_UP),
+ KEY(1, 2, KEY_2),
+ KEY(1, 3, KEY_F9),
+ KEY(1, 4, KEY_F7),
+ KEY(1, 5, KEY_0),
+ KEY(2, 0, KEY_ENTER),
+ KEY(2, 1, KEY_6),
+ KEY(2, 2, KEY_1),
+ KEY(2, 3, KEY_F2),
+ KEY(2, 4, KEY_F6),
+ KEY(2, 5, KEY_HOME),
+ KEY(3, 0, KEY_8),
+ KEY(3, 1, KEY_5),
+ KEY(3, 2, KEY_F12),
+ KEY(3, 3, KEY_F3),
+ KEY(3, 4, KEY_F8),
+ KEY(3, 5, KEY_END),
+ KEY(4, 0, KEY_7),
+ KEY(4, 1, KEY_4),
+ KEY(4, 2, KEY_F11),
+ KEY(4, 3, KEY_F1),
+ KEY(4, 4, KEY_F4),
+ KEY(4, 5, KEY_ESC),
+ KEY(5, 0, KEY_F13),
+ KEY(5, 1, KEY_F14),
+ KEY(5, 2, KEY_F15),
+ KEY(5, 3, KEY_F16),
+ KEY(5, 4, KEY_SLEEP),
+ 0
+};
+
+
+static struct mtd_partition nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
}
};
-static struct flash_platform_data h3_flash_data = {
+static struct flash_platform_data nor_data = {
.map_name = "cfi_probe",
.width = 2,
- .parts = h3_partitions,
- .nr_parts = ARRAY_SIZE(h3_partitions),
+ .parts = nor_partitions,
+ .nr_parts = ARRAY_SIZE(nor_partitions),
};
-static struct resource h3_flash_resource = {
+static struct resource nor_resource = {
/* This is on CS3, wherever it's mapped */
.flags = IORESOURCE_MEM,
};
-static struct platform_device flash_device = {
+static struct platform_device nor_device = {
.name = "omapflash",
.id = 0,
.dev = {
- .platform_data = &h3_flash_data,
+ .platform_data = &nor_data,
+ },
+ .num_resources = 1,
+ .resource = &nor_resource,
+};
+
+static struct mtd_partition nand_partitions[] = {
+#if 0
+ /* REVISIT: enable these partitions if you make NAND BOOT work */
+ {
+ .name = "xloader",
+ .offset = 0,
+ .size = 64 * 1024,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "bootloader",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 256 * 1024,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "params",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 192 * 1024,
+ },
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 2 * SZ_1M,
+ },
+#endif
+ {
+ .name = "filesystem",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ },
+};
+
+/* dip switches control NAND chip access: 8 bit, 16 bit, or neither */
+static struct nand_platform_data nand_data = {
+ .options = NAND_SAMSUNG_LP_OPTIONS,
+ .parts = nand_partitions,
+ .nr_parts = ARRAY_SIZE(nand_partitions),
+};
+
+static struct resource nand_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device nand_device = {
+ .name = "omapnand",
+ .id = 0,
+ .dev = {
+ .platform_data = &nand_data,
},
.num_resources = 1,
- .resource = &h3_flash_resource,
+ .resource = &nand_resource,
};
static struct resource smc91x_resources[] = {
.resource = intlat_resources,
};
+static struct resource h3_kp_resources[] = {
+ [0] = {
+ .start = INT_KEYBOARD,
+ .end = INT_KEYBOARD,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct omap_kp_platform_data h3_kp_data = {
+ .rows = 8,
+ .cols = 8,
+ .keymap = h3_keymap,
+ .rep = 1,
+};
+
+static struct platform_device h3_kp_device = {
+ .name = "omap-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &h3_kp_data,
+ },
+ .num_resources = ARRAY_SIZE(h3_kp_resources),
+ .resource = h3_kp_resources,
+};
+
+
+/* Select between the IrDA and aGPS module
+ */
+static int h3_select_irda(struct device *dev, int state)
+{
+ unsigned char expa;
+ int err = 0;
+
+ if ((err = read_gpio_expa(&expa, 0x26))) {
+ printk(KERN_ERR "Error reading from I/O EXPANDER \n");
+ return err;
+ }
+
+ /* 'P6' enable/disable IRDA_TX and IRDA_RX */
+ if (state & IR_SEL) { /* IrDA */
+ if ((err = write_gpio_expa(expa | 0x40, 0x26))) {
+ printk(KERN_ERR "Error writing to I/O EXPANDER \n");
+ return err;
+ }
+ } else {
+ if ((err = write_gpio_expa(expa & ~0x40, 0x26))) {
+ printk(KERN_ERR "Error writing to I/O EXPANDER \n");
+ return err;
+ }
+ }
+ return err;
+}
+
+static void set_trans_mode(void *data)
+{
+ int *mode = data;
+ unsigned char expa;
+ int err = 0;
+
+ if ((err = read_gpio_expa(&expa, 0x27)) != 0) {
+ printk(KERN_ERR "Error reading from I/O expander\n");
+ }
+
+ expa &= ~0x03;
+
+ if (*mode & IR_SIRMODE) {
+ expa |= 0x01;
+ } else { /* MIR/FIR */
+ expa |= 0x03;
+ }
+
+ if ((err = write_gpio_expa(expa, 0x27)) != 0) {
+ printk(KERN_ERR "Error writing to I/O expander\n");
+ }
+}
+
+static int h3_transceiver_mode(struct device *dev, int mode)
+{
+ struct omap_irda_config *irda_config = dev->platform_data;
+
+ cancel_delayed_work(&irda_config->gpio_expa);
+ PREPARE_WORK(&irda_config->gpio_expa, set_trans_mode, &mode);
+ schedule_work(&irda_config->gpio_expa);
+
+ return 0;
+}
+
+static struct omap_irda_config h3_irda_data = {
+ .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
+ .transceiver_mode = h3_transceiver_mode,
+ .select_irda = h3_select_irda,
+ .rx_channel = OMAP_DMA_UART3_RX,
+ .tx_channel = OMAP_DMA_UART3_TX,
+ .dest_start = UART3_THR,
+ .src_start = UART3_RHR,
+ .tx_trigger = 0,
+ .rx_trigger = 0,
+};
+
+static struct resource h3_irda_resources[] = {
+ [0] = {
+ .start = INT_UART3,
+ .end = INT_UART3,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device h3_irda_device = {
+ .name = "omapirda",
+ .id = 0,
+ .dev = {
+ .platform_data = &h3_irda_data,
+ },
+ .num_resources = ARRAY_SIZE(h3_irda_resources),
+ .resource = h3_irda_resources,
+};
+
+static struct platform_device h3_lcd_device = {
+ .name = "lcd_h3",
+ .id = -1,
+};
+
static struct platform_device *devices[] __initdata = {
- &flash_device,
+ &nor_device,
+ &nand_device,
&smc91x_device,
&intlat_device,
+ &h3_irda_device,
+ &h3_kp_device,
+ &h3_lcd_device,
};
static struct omap_usb_config h3_usb_config __initdata = {
};
static struct omap_lcd_config h3_lcd_config __initdata = {
- .panel_name = "h3",
.ctrl_name = "internal",
};
{ OMAP_TAG_LCD, &h3_lcd_config },
};
+#define H3_NAND_RB_GPIO_PIN 10
+
+static int nand_dev_ready(struct nand_platform_data *data)
+{
+ return omap_get_gpio_datain(H3_NAND_RB_GPIO_PIN);
+}
+
static void __init h3_init(void)
{
- h3_flash_resource.end = h3_flash_resource.start = omap_cs3_phys();
- h3_flash_resource.end += OMAP_CS3_SIZE - 1;
- (void) platform_add_devices(devices, ARRAY_SIZE(devices));
+ /* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
+ * to address 0 by a dip switch), NAND on CS2B. The NAND driver will
+ * notice whether a NAND chip is enabled at probe time.
+ *
+ * H3 support NAND-boot, with a dip switch to put NOR on CS2B and NAND
+ * (which on H2 may be 16bit) on CS3. Try detecting that in code here,
+ * to avoid probing every possible flash configuration...
+ */
+ nor_resource.end = nor_resource.start = omap_cs3_phys();
+ nor_resource.end += SZ_32M - 1;
+
+ nand_resource.end = nand_resource.start = OMAP_CS2B_PHYS;
+ nand_resource.end += SZ_4K - 1;
+ if (!(omap_request_gpio(H3_NAND_RB_GPIO_PIN)))
+ nand_data.dev_ready = nand_dev_ready;
+
+ /* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
+ /* GPIO10 pullup/down register, Enable pullup on GPIO10 */
+ omap_cfg_reg(V2_1710_GPIO10);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = h3_config;
omap_board_config_size = ARRAY_SIZE(h3_config);
omap_serial_init();
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/input.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/gpio.h>
#include <asm/arch/tc.h>
#include <asm/arch/usb.h>
+#include <asm/arch/keypad.h>
#include <asm/arch/common.h>
+static int innovator_keymap[] = {
+ KEY(0, 0, KEY_F1),
+ KEY(0, 3, KEY_DOWN),
+ KEY(1, 1, KEY_F2),
+ KEY(1, 2, KEY_RIGHT),
+ KEY(2, 0, KEY_F3),
+ KEY(2, 1, KEY_F4),
+ KEY(2, 2, KEY_UP),
+ KEY(3, 2, KEY_ENTER),
+ KEY(3, 3, KEY_LEFT),
+ 0
+};
+
static struct mtd_partition innovator_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.resource = &innovator_flash_resource,
};
+static struct resource innovator_kp_resources[] = {
+ [0] = {
+ .start = INT_KEYBOARD,
+ .end = INT_KEYBOARD,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct omap_kp_platform_data innovator_kp_data = {
+ .rows = 8,
+ .cols = 8,
+ .keymap = innovator_keymap,
+};
+
+static struct platform_device innovator_kp_device = {
+ .name = "omap-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &innovator_kp_data,
+ },
+ .num_resources = ARRAY_SIZE(innovator_kp_resources),
+ .resource = innovator_kp_resources,
+};
+
+
#ifdef CONFIG_ARCH_OMAP15XX
/* Only FPGA needs to be mapped here. All others are done with ioremap */
.resource = innovator1510_smc91x_resources,
};
+static struct platform_device innovator1510_lcd_device = {
+ .name = "lcd_inn1510",
+ .id = -1,
+};
+
static struct platform_device *innovator1510_devices[] __initdata = {
&innovator_flash_device,
&innovator1510_smc91x_device,
+ &innovator_kp_device,
+ &innovator1510_lcd_device,
};
#endif /* CONFIG_ARCH_OMAP15XX */
.resource = innovator1610_smc91x_resources,
};
+static struct platform_device innovator1610_lcd_device = {
+ .name = "inn1610_lcd",
+ .id = -1,
+};
+
static struct platform_device *innovator1610_devices[] __initdata = {
&innovator_flash_device,
&innovator1610_smc91x_device,
+ &innovator_kp_device,
+ &innovator1610_lcd_device,
};
#endif /* CONFIG_ARCH_OMAP16XX */
};
static struct omap_lcd_config innovator1510_lcd_config __initdata = {
- .panel_name = "inn1510",
.ctrl_name = "internal",
};
#endif
};
static struct omap_lcd_config innovator1610_lcd_config __initdata = {
- .panel_name = "inn1610",
.ctrl_name = "internal",
};
#endif
+++ /dev/null
-/*
- * Modified from board-generic.c
- *
- * Copyright (C) 2004 2N Telekomunikace, Ladislav Michl <michl@2n.cz>
- *
- * Code for Netstar OMAP board.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/notifier.h>
-#include <linux/reboot.h>
-
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/common.h>
-
-extern void __init omap_init_time(void);
-extern int omap_gpio_init(void);
-
-static struct resource netstar_smc91x_resources[] = {
- [0] = {
- .start = OMAP_CS1_PHYS + 0x300,
- .end = OMAP_CS1_PHYS + 0x300 + 16,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = OMAP_GPIO_IRQ(8),
- .end = OMAP_GPIO_IRQ(8),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device netstar_smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(netstar_smc91x_resources),
- .resource = netstar_smc91x_resources,
-};
-
-static struct platform_device *netstar_devices[] __initdata = {
- &netstar_smc91x_device,
-};
-
-static struct omap_uart_config netstar_uart_config __initdata = {
- .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
-static struct omap_board_config_kernel netstar_config[] = {
- { OMAP_TAG_UART, &netstar_uart_config },
-};
-
-static void __init netstar_init_irq(void)
-{
- omap1_init_common_hw();
- omap_init_irq();
- omap_gpio_init();
-}
-
-static void __init netstar_init(void)
-{
- /* green LED */
- omap_request_gpio(4);
- omap_set_gpio_direction(4, 0);
- /* smc91x reset */
- omap_request_gpio(7);
- omap_set_gpio_direction(7, 0);
- omap_set_gpio_dataout(7, 1);
- udelay(2); /* wait at least 100ns */
- omap_set_gpio_dataout(7, 0);
- mdelay(50); /* 50ms until PHY ready */
- /* smc91x interrupt pin */
- omap_request_gpio(8);
-
- omap_request_gpio(12);
- omap_request_gpio(13);
- omap_request_gpio(14);
- omap_request_gpio(15);
- set_irq_type(OMAP_GPIO_IRQ(12), IRQT_FALLING);
- set_irq_type(OMAP_GPIO_IRQ(13), IRQT_FALLING);
- set_irq_type(OMAP_GPIO_IRQ(14), IRQT_FALLING);
- set_irq_type(OMAP_GPIO_IRQ(15), IRQT_FALLING);
-
- platform_add_devices(netstar_devices, ARRAY_SIZE(netstar_devices));
-
- /* Switch on green LED */
- omap_set_gpio_dataout(4, 0);
- /* Switch off red LED */
- omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
- omap_writeb(0x80, OMAP_LPG1_LCR);
-
- omap_board_config = netstar_config;
- omap_board_config_size = ARRAY_SIZE(netstar_config);
- omap_serial_init();
-}
-
-static void __init netstar_map_io(void)
-{
- omap1_map_common_io();
-}
-
-#define MACHINE_PANICED 1
-#define MACHINE_REBOOTING 2
-#define MACHINE_REBOOT 4
-static unsigned long machine_state;
-
-static int panic_event(struct notifier_block *this, unsigned long event,
- void *ptr)
-{
- if (test_and_set_bit(MACHINE_PANICED, &machine_state))
- return NOTIFY_DONE;
-
- /* Switch off green LED */
- omap_set_gpio_dataout(4, 1);
- /* Flash red LED */
- omap_writeb(0x78, OMAP_LPG1_LCR);
- omap_writeb(0x01, OMAP_LPG1_PMR); /* Enable clock */
-
- return NOTIFY_DONE;
-}
-
-static struct notifier_block panic_block = {
- .notifier_call = panic_event,
-};
-
-static int __init netstar_late_init(void)
-{
- /* TODO: Setup front panel switch here */
-
- /* Setup panic notifier */
- atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
-
- return 0;
-}
-
-postcore_initcall(netstar_late_init);
-
-MACHINE_START(NETSTAR, "NetStar OMAP5910")
- /* Maintainer: Ladislav Michl <michl@2n.cz> */
- .phys_io = 0xfff00000,
- .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
- .boot_params = 0x10000100,
- .map_io = netstar_map_io,
- .init_irq = netstar_init_irq,
- .init_machine = netstar_init,
- .timer = &omap_timer,
-MACHINE_END
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/board-nokia770.c
+ *
+ * Modified from board-generic.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/input.h>
+#include <linux/clk.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <asm/arch/gpio.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/usb.h>
+#include <asm/arch/board.h>
+#include <asm/arch/keypad.h>
+#include <asm/arch/common.h>
+#include <asm/arch/dsp_common.h>
+#include <asm/arch/aic23.h>
+#include <asm/arch/gpio.h>
+
+static void __init omap_nokia770_init_irq(void)
+{
+ /* On Nokia 770, the SleepX signal is masked with an
+ * MPUIO line by default. It has to be unmasked for it
+ * to become functional */
+
+ /* SleepX mask direction */
+ omap_writew((omap_readw(0xfffb5008) & ~2), 0xfffb5008);
+ /* Unmask SleepX signal */
+ omap_writew((omap_readw(0xfffb5004) & ~2), 0xfffb5004);
+
+ omap1_init_common_hw();
+ omap_init_irq();
+}
+
+static int nokia770_keymap[] = {
+ KEY(0, 1, GROUP_0 | KEY_UP),
+ KEY(0, 2, GROUP_1 | KEY_F5),
+ KEY(1, 0, GROUP_0 | KEY_LEFT),
+ KEY(1, 1, GROUP_0 | KEY_ENTER),
+ KEY(1, 2, GROUP_0 | KEY_RIGHT),
+ KEY(2, 0, GROUP_1 | KEY_ESC),
+ KEY(2, 1, GROUP_0 | KEY_DOWN),
+ KEY(2, 2, GROUP_1 | KEY_F4),
+ KEY(3, 0, GROUP_2 | KEY_F7),
+ KEY(3, 1, GROUP_2 | KEY_F8),
+ KEY(3, 2, GROUP_2 | KEY_F6),
+ 0
+};
+
+static struct resource nokia770_kp_resources[] = {
+ [0] = {
+ .start = INT_KEYBOARD,
+ .end = INT_KEYBOARD,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct omap_kp_platform_data nokia770_kp_data = {
+ .rows = 8,
+ .cols = 8,
+ .keymap = nokia770_keymap
+};
+
+static struct platform_device nokia770_kp_device = {
+ .name = "omap-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &nokia770_kp_data,
+ },
+ .num_resources = ARRAY_SIZE(nokia770_kp_resources),
+ .resource = nokia770_kp_resources,
+};
+
+static struct platform_device *nokia770_devices[] __initdata = {
+ &nokia770_kp_device,
+};
+
+static struct ads7846_platform_data nokia770_ads7846_platform_data __initdata = {
+ .x_max = 0x0fff,
+ .y_max = 0x0fff,
+ .x_plate_ohms = 180,
+ .pressure_max = 255,
+ .debounce_max = 10,
+ .debounce_tol = 3,
+};
+
+static struct spi_board_info nokia770_spi_board_info[] __initdata = {
+ [0] = {
+ .modalias = "lcd_lph8923",
+ .bus_num = 2,
+ .chip_select = 3,
+ .max_speed_hz = 12000000,
+ },
+ [1] = {
+ .modalias = "ads7846",
+ .bus_num = 2,
+ .chip_select = 0,
+ .max_speed_hz = 2500000,
+ .irq = OMAP_GPIO_IRQ(15),
+ .platform_data = &nokia770_ads7846_platform_data,
+ },
+};
+
+
+/* assume no Mini-AB port */
+
+static struct omap_usb_config nokia770_usb_config __initdata = {
+ .otg = 1,
+ .register_host = 1,
+ .register_dev = 1,
+ .hmc_mode = 16,
+ .pins[0] = 6,
+};
+
+static struct omap_mmc_config nokia770_mmc_config __initdata = {
+ .mmc[0] = {
+ .enabled = 0,
+ .wire4 = 0,
+ .wp_pin = -1,
+ .power_pin = -1,
+ .switch_pin = -1,
+ },
+ .mmc[1] = {
+ .enabled = 0,
+ .wire4 = 0,
+ .wp_pin = -1,
+ .power_pin = -1,
+ .switch_pin = -1,
+ },
+};
+
+static struct omap_board_config_kernel nokia770_config[] = {
+ { OMAP_TAG_USB, NULL },
+ { OMAP_TAG_MMC, &nokia770_mmc_config },
+};
+
+/*
+ * audio power control
+ */
+#define HEADPHONE_GPIO 14
+#define AMPLIFIER_CTRL_GPIO 58
+
+static struct clk *dspxor_ck;
+static DECLARE_MUTEX(audio_pwr_sem);
+/*
+ * audio_pwr_state
+ * +--+-------------------------+---------------------------------------+
+ * |-1|down |power-up request -> 0 |
+ * +--+-------------------------+---------------------------------------+
+ * | 0|up |power-down(1) request -> 1 |
+ * | | |power-down(2) request -> (ignore) |
+ * +--+-------------------------+---------------------------------------+
+ * | 1|up, |power-up request -> 0 |
+ * | |received down(1) request |power-down(2) request -> -1 |
+ * +--+-------------------------+---------------------------------------+
+ */
+static int audio_pwr_state = -1;
+
+/*
+ * audio_pwr_up / down should be called under audio_pwr_sem
+ */
+static void nokia770_audio_pwr_up(void)
+{
+ clk_enable(dspxor_ck);
+
+ /* Turn on codec */
+ tlv320aic23_power_up();
+
+ if (omap_get_gpio_datain(HEADPHONE_GPIO))
+ /* HP not connected, turn on amplifier */
+ omap_set_gpio_dataout(AMPLIFIER_CTRL_GPIO, 1);
+ else
+ /* HP connected, do not turn on amplifier */
+ printk("HP connected\n");
+}
+
+static void codec_delayed_power_down(void *arg)
+{
+ down(&audio_pwr_sem);
+ if (audio_pwr_state == -1)
+ tlv320aic23_power_down();
+ clk_disable(dspxor_ck);
+ up(&audio_pwr_sem);
+}
+
+static DECLARE_WORK(codec_power_down_work, codec_delayed_power_down, NULL);
+
+static void nokia770_audio_pwr_down(void)
+{
+ /* Turn off amplifier */
+ omap_set_gpio_dataout(AMPLIFIER_CTRL_GPIO, 0);
+
+ /* Turn off codec: schedule delayed work */
+ schedule_delayed_work(&codec_power_down_work, HZ / 20); /* 50ms */
+}
+
+void nokia770_audio_pwr_up_request(int stage)
+{
+ down(&audio_pwr_sem);
+ if (audio_pwr_state == -1)
+ nokia770_audio_pwr_up();
+ /* force audio_pwr_state = 0, even if it was 1. */
+ audio_pwr_state = 0;
+ up(&audio_pwr_sem);
+}
+
+void nokia770_audio_pwr_down_request(int stage)
+{
+ down(&audio_pwr_sem);
+ switch (stage) {
+ case 1:
+ if (audio_pwr_state == 0)
+ audio_pwr_state = 1;
+ break;
+ case 2:
+ if (audio_pwr_state == 1) {
+ nokia770_audio_pwr_down();
+ audio_pwr_state = -1;
+ }
+ break;
+ }
+ up(&audio_pwr_sem);
+}
+
+static void __init omap_nokia770_init(void)
+{
+ nokia770_config[0].data = &nokia770_usb_config;
+
+ platform_add_devices(nokia770_devices, ARRAY_SIZE(nokia770_devices));
+ spi_register_board_info(nokia770_spi_board_info,
+ ARRAY_SIZE(nokia770_spi_board_info));
+ omap_board_config = nokia770_config;
+ omap_board_config_size = ARRAY_SIZE(nokia770_config);
+ omap_serial_init();
+ omap_dsp_audio_pwr_up_request = nokia770_audio_pwr_up_request;
+ omap_dsp_audio_pwr_down_request = nokia770_audio_pwr_down_request;
+ dspxor_ck = clk_get(0, "dspxor_ck");
+}
+
+static void __init omap_nokia770_map_io(void)
+{
+ omap1_map_common_io();
+}
+
+MACHINE_START(NOKIA770, "Nokia 770")
+ .phys_io = 0xfff00000,
+ .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
+ .boot_params = 0x10000100,
+ .map_io = omap_nokia770_map_io,
+ .init_irq = omap_nokia770_init_irq,
+ .init_machine = omap_nokia770_init,
+ .timer = &omap_timer,
+MACHINE_END
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/input.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/usb.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
+#include <asm/arch/keypad.h>
#include <asm/arch/common.h>
+#include <asm/arch/mcbsp.h>
+#include <asm/arch/omap-alsa.h>
+
+static int osk_keymap[] = {
+ KEY(0, 0, KEY_F1),
+ KEY(0, 3, KEY_UP),
+ KEY(1, 1, KEY_LEFTCTRL),
+ KEY(1, 2, KEY_LEFT),
+ KEY(2, 0, KEY_SPACE),
+ KEY(2, 1, KEY_ESC),
+ KEY(2, 2, KEY_DOWN),
+ KEY(3, 2, KEY_ENTER),
+ KEY(3, 3, KEY_RIGHT),
+ 0
+};
+
static struct mtd_partition osk_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
.resource = osk5912_cf_resources,
};
+#define DEFAULT_BITPERSAMPLE 16
+
+static struct omap_mcbsp_reg_cfg mcbsp_regs = {
+ .spcr2 = FREE | FRST | GRST | XRST | XINTM(3),
+ .spcr1 = RINTM(3) | RRST,
+ .rcr2 = RPHASE | RFRLEN2(OMAP_MCBSP_WORD_8) |
+ RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(0),
+ .rcr1 = RFRLEN1(OMAP_MCBSP_WORD_8) | RWDLEN1(OMAP_MCBSP_WORD_16),
+ .xcr2 = XPHASE | XFRLEN2(OMAP_MCBSP_WORD_8) |
+ XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(0) | XFIG,
+ .xcr1 = XFRLEN1(OMAP_MCBSP_WORD_8) | XWDLEN1(OMAP_MCBSP_WORD_16),
+ .srgr1 = FWID(DEFAULT_BITPERSAMPLE - 1),
+ .srgr2 = GSYNC | CLKSP | FSGM | FPER(DEFAULT_BITPERSAMPLE * 2 - 1),
+ /*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */
+ .pcr0 = CLKXP | CLKRP, /* mcbsp: slave */
+};
+
+static struct omap_alsa_codec_config alsa_config = {
+ .name = "OSK AIC23",
+ .mcbsp_regs_alsa = &mcbsp_regs,
+ .codec_configure_dev = NULL, // aic23_configure,
+ .codec_set_samplerate = NULL, // aic23_set_samplerate,
+ .codec_clock_setup = NULL, // aic23_clock_setup,
+ .codec_clock_on = NULL, // aic23_clock_on,
+ .codec_clock_off = NULL, // aic23_clock_off,
+ .get_default_samplerate = NULL, // aic23_get_default_samplerate,
+};
+
static struct platform_device osk5912_mcbsp1_device = {
- .name = "omap_mcbsp",
- .id = 1,
+ .name = "omap_alsa_mcbsp",
+ .id = 1,
+ .dev = {
+ .platform_data = &alsa_config,
+ },
+};
+
+static struct resource osk5912_kp_resources[] = {
+ [0] = {
+ .start = INT_KEYBOARD,
+ .end = INT_KEYBOARD,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct omap_kp_platform_data osk_kp_data = {
+ .rows = 8,
+ .cols = 8,
+ .keymap = osk_keymap,
+};
+
+static struct platform_device osk5912_kp_device = {
+ .name = "omap-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &osk_kp_data,
+ },
+ .num_resources = ARRAY_SIZE(osk5912_kp_resources),
+ .resource = osk5912_kp_resources,
+};
+
+static struct platform_device osk5912_lcd_device = {
+ .name = "lcd_osk",
+ .id = -1,
};
static struct platform_device *osk5912_devices[] __initdata = {
&osk5912_smc91x_device,
&osk5912_cf_device,
&osk5912_mcbsp1_device,
+ &osk5912_kp_device,
+ &osk5912_lcd_device,
};
static void __init osk_init_smc91x(void)
};
static struct omap_lcd_config osk_lcd_config __initdata = {
- .panel_name = "osk",
.ctrl_name = "internal",
};
static void __init osk_mistral_init(void) { }
#endif
+#define EMIFS_CS3_VAL (0x88013141)
+
static void __init osk_init(void)
{
+ /* Workaround for wrong CS3 (NOR flash) timing
+ * There are some U-Boot versions out there which configure
+ * wrong CS3 memory timings. This mainly leads to CRC
+ * or similiar errors if you use NOR flash (e.g. with JFFS2)
+ */
+ if (EMIFS_CCS(3) != EMIFS_CS3_VAL)
+ EMIFS_CCS(3) = EMIFS_CS3_VAL;
+
osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
osk_flash_resource.end += SZ_32M - 1;
platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
omap_init_irq();
}
+static struct platform_device palmte_lcd_device = {
+ .name = "lcd_palmte",
+ .id = -1,
+};
+
+static struct platform_device *devices[] __initdata = {
+ &palmte_lcd_device,
+};
+
static struct omap_usb_config palmte_usb_config __initdata = {
.register_dev = 1,
.hmc_mode = 0,
};
static struct omap_lcd_config palmte_lcd_config __initdata = {
- .panel_name = "palmte",
.ctrl_name = "internal",
};
{
omap_board_config = palmte_config;
omap_board_config_size = ARRAY_SIZE(palmte_config);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
}
static void __init omap_generic_map_io(void)
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
+#include <linux/input.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/fpga.h>
+#include <asm/arch/keypad.h>
#include <asm/arch/common.h>
#include <asm/arch/board.h>
+static int p2_keymap[] = {
+ KEY(0,0,KEY_UP),
+ KEY(0,1,KEY_RIGHT),
+ KEY(0,2,KEY_LEFT),
+ KEY(0,3,KEY_DOWN),
+ KEY(0,4,KEY_CENTER),
+ KEY(0,5,KEY_0_5),
+ KEY(1,0,KEY_SOFT2),
+ KEY(1,1,KEY_SEND),
+ KEY(1,2,KEY_END),
+ KEY(1,3,KEY_VOLUMEDOWN),
+ KEY(1,4,KEY_VOLUMEUP),
+ KEY(1,5,KEY_RECORD),
+ KEY(2,0,KEY_SOFT1),
+ KEY(2,1,KEY_3),
+ KEY(2,2,KEY_6),
+ KEY(2,3,KEY_9),
+ KEY(2,4,KEY_SHARP),
+ KEY(2,5,KEY_2_5),
+ KEY(3,0,KEY_BACK),
+ KEY(3,1,KEY_2),
+ KEY(3,2,KEY_5),
+ KEY(3,3,KEY_8),
+ KEY(3,4,KEY_0),
+ KEY(3,5,KEY_HEADSETHOOK),
+ KEY(4,0,KEY_HOME),
+ KEY(4,1,KEY_1),
+ KEY(4,2,KEY_4),
+ KEY(4,3,KEY_7),
+ KEY(4,4,KEY_STAR),
+ KEY(4,5,KEY_POWER),
+ 0
+};
+
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
},
};
-static struct mtd_partition p2_partitions[] = {
+static struct mtd_partition nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
},
};
-static struct flash_platform_data p2_flash_data = {
+static struct flash_platform_data nor_data = {
.map_name = "cfi_probe",
.width = 2,
- .parts = p2_partitions,
- .nr_parts = ARRAY_SIZE(p2_partitions),
+ .parts = nor_partitions,
+ .nr_parts = ARRAY_SIZE(nor_partitions),
};
-static struct resource p2_flash_resource = {
+static struct resource nor_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_32M - 1,
.flags = IORESOURCE_MEM,
};
-static struct platform_device p2_flash_device = {
+static struct platform_device nor_device = {
.name = "omapflash",
.id = 0,
.dev = {
- .platform_data = &p2_flash_data,
+ .platform_data = &nor_data,
+ },
+ .num_resources = 1,
+ .resource = &nor_resource,
+};
+
+static struct nand_platform_data nand_data = {
+ .options = NAND_SAMSUNG_LP_OPTIONS,
+};
+
+static struct resource nand_resource = {
+ .start = OMAP_CS3_PHYS,
+ .end = OMAP_CS3_PHYS + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device nand_device = {
+ .name = "omapnand",
+ .id = 0,
+ .dev = {
+ .platform_data = &nand_data,
},
.num_resources = 1,
- .resource = &p2_flash_resource,
+ .resource = &nand_resource,
};
static struct platform_device smc91x_device = {
.resource = smc91x_resources,
};
+static struct resource kp_resources[] = {
+ [0] = {
+ .start = INT_730_MPUIO_KEYPAD,
+ .end = INT_730_MPUIO_KEYPAD,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct omap_kp_platform_data kp_data = {
+ .rows = 8,
+ .cols = 8,
+ .keymap = p2_keymap,
+};
+
+static struct platform_device kp_device = {
+ .name = "omap-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &kp_data,
+ },
+ .num_resources = ARRAY_SIZE(kp_resources),
+ .resource = kp_resources,
+};
+
+static struct platform_device lcd_device = {
+ .name = "lcd_p2",
+ .id = -1,
+};
+
static struct platform_device *devices[] __initdata = {
- &p2_flash_device,
+ &nor_device,
+ &nand_device,
&smc91x_device,
+ &kp_device,
+ &lcd_device,
};
+#define P2_NAND_RB_GPIO_PIN 62
+
+static int nand_dev_ready(struct nand_platform_data *data)
+{
+ return omap_get_gpio_datain(P2_NAND_RB_GPIO_PIN);
+}
+
static struct omap_uart_config perseus2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1)),
};
static struct omap_lcd_config perseus2_lcd_config __initdata = {
- .panel_name = "p2",
.ctrl_name = "internal",
};
static void __init omap_perseus2_init(void)
{
- (void) platform_add_devices(devices, ARRAY_SIZE(devices));
+ if (!(omap_request_gpio(P2_NAND_RB_GPIO_PIN)))
+ nand_data.dev_ready = nand_dev_ready;
+
+ omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
+ omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = perseus2_config;
omap_board_config_size = ARRAY_SIZE(perseus2_config);
};
static struct omap_board_config_kernel voiceblue_config[] = {
- { OMAP_TAG_USB, &voiceblue_usb_config },
- { OMAP_TAG_MMC, &voiceblue_mmc_config },
- { OMAP_TAG_UART, &voiceblue_uart_config },
+ { OMAP_TAG_USB, &voiceblue_usb_config },
+ { OMAP_TAG_MMC, &voiceblue_mmc_config },
+ { OMAP_TAG_UART, &voiceblue_uart_config },
};
static void __init voiceblue_init_irq(void)
static int __init voiceblue_setup(void)
{
/* Setup panic notifier */
- atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
+ notifier_chain_register(&panic_notifier_list, &panic_block);
return 0;
}
static inline void omap_init_rtc(void) {}
#endif
+#if defined(CONFIG_OMAP_STI)
+
+#define OMAP1_STI_BASE IO_ADDRESS(0xfffea000)
+#define OMAP1_STI_CHANNEL_BASE (OMAP1_STI_BASE + 0x400)
+
+static struct resource sti_resources[] = {
+ {
+ .start = OMAP1_STI_BASE,
+ .end = OMAP1_STI_BASE + SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP1_STI_CHANNEL_BASE,
+ .end = OMAP1_STI_CHANNEL_BASE + SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = INT_1610_STI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device sti_device = {
+ .name = "sti",
+ .id = -1,
+ .dev = {
+ .release = omap_nop_release,
+ },
+ .num_resources = ARRAY_SIZE(sti_resources),
+ .resource = sti_resources,
+};
+
+static inline void omap_init_sti(void)
+{
+ platform_device_register(&sti_device);
+}
+#else
+static inline void omap_init_sti(void) {}
+#endif
/*-------------------------------------------------------------------------*/
*/
omap_init_irda();
omap_init_rtc();
+ omap_init_sti();
return 0;
}
bool "OMAP 2420 H4 board"
depends on ARCH_OMAP2 && ARCH_OMAP24XX
+config MACH_OMAP_APOLLON
+ bool "OMAP 2420 Apollon board"
+ depends on ARCH_OMAP2 && ARCH_OMAP24XX
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap/omap2/board-apollon.c
+ *
+ * Copyright (C) 2005,2006 Samsung Electronics
+ * Author: Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ * Modified from mach-omap/omap2/board-h4.c
+ *
+ * Code for apollon OMAP2 board. Should work on many OMAP2 systems where
+ * the bootloader passes the board-specific data to the kernel.
+ * Do not put any board specific code to this file; create a new machine
+ * type if you need custom low-level initializations.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/onenand.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+#include <asm/arch/gpio.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/usb.h>
+#include <asm/arch/board.h>
+#include <asm/arch/common.h>
+#include "prcm-regs.h"
+
+/* LED & Switch macros */
+#define LED0_GPIO13 13
+#define LED1_GPIO14 14
+#define LED2_GPIO15 15
+#define SW_ENTER_GPIO16 16
+#define SW_UP_GPIO17 17
+#define SW_DOWN_GPIO58 58
+
+static struct mtd_partition apollon_partitions[] = {
+ {
+ .name = "X-Loader + U-Boot",
+ .offset = 0,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE,
+ },
+ {
+ .name = "params",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_128K,
+ },
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_2M,
+ },
+ {
+ .name = "rootfs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_16M,
+ },
+ {
+ .name = "filesystem00",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_32M,
+ },
+ {
+ .name = "filesystem01",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct flash_platform_data apollon_flash_data = {
+ .parts = apollon_partitions,
+ .nr_parts = ARRAY_SIZE(apollon_partitions),
+};
+
+static struct resource apollon_flash_resource = {
+ .start = APOLLON_CS0_BASE,
+ .end = APOLLON_CS0_BASE + SZ_128K,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device apollon_onenand_device = {
+ .name = "onenand",
+ .id = -1,
+ .dev = {
+ .platform_data = &apollon_flash_data,
+ },
+ .num_resources = ARRAY_SIZE(&apollon_flash_resource),
+ .resource = &apollon_flash_resource,
+};
+
+static struct resource apollon_smc91x_resources[] = {
+ [0] = {
+ .start = APOLLON_ETHR_START, /* Physical */
+ .end = APOLLON_ETHR_START + 0xf,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = OMAP_GPIO_IRQ(APOLLON_ETHR_GPIO_IRQ),
+ .end = OMAP_GPIO_IRQ(APOLLON_ETHR_GPIO_IRQ),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device apollon_smc91x_device = {
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(apollon_smc91x_resources),
+ .resource = apollon_smc91x_resources,
+};
+
+static struct platform_device apollon_lcd_device = {
+ .name = "apollon_lcd",
+ .id = -1,
+};
+
+static struct platform_device *apollon_devices[] __initdata = {
+ &apollon_onenand_device,
+ &apollon_smc91x_device,
+ &apollon_lcd_device,
+};
+
+static inline void __init apollon_init_smc91x(void)
+{
+ /* Make sure CS1 timings are correct */
+ GPMC_CONFIG1_1 = 0x00011203;
+ GPMC_CONFIG2_1 = 0x001f1f01;
+ GPMC_CONFIG3_1 = 0x00080803;
+ GPMC_CONFIG4_1 = 0x1c091c09;
+ GPMC_CONFIG5_1 = 0x041f1f1f;
+ GPMC_CONFIG6_1 = 0x000004c4;
+ GPMC_CONFIG7_1 = 0x00000f40 | (APOLLON_CS1_BASE >> 24);
+ udelay(100);
+
+ omap_cfg_reg(W4__24XX_GPIO74);
+ if (omap_request_gpio(APOLLON_ETHR_GPIO_IRQ) < 0) {
+ printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
+ APOLLON_ETHR_GPIO_IRQ);
+ return;
+ }
+ omap_set_gpio_direction(APOLLON_ETHR_GPIO_IRQ, 1);
+}
+
+static void __init omap_apollon_init_irq(void)
+{
+ omap2_init_common_hw();
+ omap_init_irq();
+ omap_gpio_init();
+ apollon_init_smc91x();
+}
+
+static struct omap_uart_config apollon_uart_config __initdata = {
+ .enabled_uarts = (1 << 0) | (0 << 1) | (0 << 2),
+};
+
+static struct omap_mmc_config apollon_mmc_config __initdata = {
+ .mmc [0] = {
+ .enabled = 0,
+ .wire4 = 0,
+ .wp_pin = -1,
+ .power_pin = -1,
+ .switch_pin = -1,
+ },
+};
+
+static struct omap_lcd_config apollon_lcd_config __initdata = {
+ .ctrl_name = "internal",
+};
+
+static struct omap_board_config_kernel apollon_config[] = {
+ { OMAP_TAG_UART, &apollon_uart_config },
+ { OMAP_TAG_MMC, &apollon_mmc_config },
+ { OMAP_TAG_LCD, &apollon_lcd_config },
+};
+
+static void __init apollon_led_init(void)
+{
+ /* LED0 - AA10 */
+ omap_cfg_reg(AA10_242X_GPIO13);
+ omap_request_gpio(LED0_GPIO13);
+ omap_set_gpio_direction(LED0_GPIO13, 0);
+ omap_set_gpio_dataout(LED0_GPIO13, 0);
+ /* LED1 - AA6 */
+ omap_cfg_reg(AA6_242X_GPIO14);
+ omap_request_gpio(LED1_GPIO14);
+ omap_set_gpio_direction(LED1_GPIO14, 0);
+ omap_set_gpio_dataout(LED1_GPIO14, 0);
+ /* LED2 - AA4 */
+ omap_cfg_reg(AA4_242X_GPIO15);
+ omap_request_gpio(LED2_GPIO15);
+ omap_set_gpio_direction(LED2_GPIO15, 0);
+ omap_set_gpio_dataout(LED2_GPIO15, 0);
+}
+
+static irqreturn_t apollon_sw_interrupt(int irq, void *ignored, struct pt_regs *regs)
+{
+ static unsigned int led0, led1, led2;
+
+ if (irq == OMAP_GPIO_IRQ(SW_ENTER_GPIO16))
+ omap_set_gpio_dataout(LED0_GPIO13, led0 ^= 1);
+ else if (irq == OMAP_GPIO_IRQ(SW_UP_GPIO17))
+ omap_set_gpio_dataout(LED1_GPIO14, led1 ^= 1);
+ else if (irq == OMAP_GPIO_IRQ(SW_DOWN_GPIO58))
+ omap_set_gpio_dataout(LED2_GPIO15, led2 ^= 1);
+
+ return IRQ_HANDLED;
+}
+
+static void __init apollon_sw_init(void)
+{
+ /* Enter SW - Y11 */
+ omap_cfg_reg(Y11_242X_GPIO16);
+ omap_request_gpio(SW_ENTER_GPIO16);
+ omap_set_gpio_direction(SW_ENTER_GPIO16, 1);
+ /* Up SW - AA12 */
+ omap_cfg_reg(AA12_242X_GPIO17);
+ omap_request_gpio(SW_UP_GPIO17);
+ omap_set_gpio_direction(SW_UP_GPIO17, 1);
+ /* Down SW - AA8 */
+ omap_cfg_reg(AA8_242X_GPIO58);
+ omap_request_gpio(SW_DOWN_GPIO58);
+ omap_set_gpio_direction(SW_DOWN_GPIO58, 1);
+
+ set_irq_type(OMAP_GPIO_IRQ(SW_ENTER_GPIO16), IRQT_RISING);
+ if (request_irq(OMAP_GPIO_IRQ(SW_ENTER_GPIO16), &apollon_sw_interrupt,
+ SA_SHIRQ, "enter sw",
+ &apollon_sw_interrupt))
+ return;
+ set_irq_type(OMAP_GPIO_IRQ(SW_UP_GPIO17), IRQT_RISING);
+ if (request_irq(OMAP_GPIO_IRQ(SW_UP_GPIO17), &apollon_sw_interrupt,
+ SA_SHIRQ, "up sw",
+ &apollon_sw_interrupt))
+ return;
+ set_irq_type(OMAP_GPIO_IRQ(SW_DOWN_GPIO58), IRQT_RISING);
+ if (request_irq(OMAP_GPIO_IRQ(SW_DOWN_GPIO58), &apollon_sw_interrupt,
+ SA_SHIRQ, "down sw",
+ &apollon_sw_interrupt))
+ return;
+}
+
+static void __init omap_apollon_init(void)
+{
+ apollon_led_init();
+ apollon_sw_init();
+
+ /* REVISIT: where's the correct place */
+ omap_cfg_reg(W19_24XX_SYS_NIRQ);
+
+ /*
+ * Make sure the serial ports are muxed on at this point.
+ * You have to mux them off in device drivers later on
+ * if not needed.
+ */
+ platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
+ omap_board_config = apollon_config;
+ omap_board_config_size = ARRAY_SIZE(apollon_config);
+ omap_serial_init();
+}
+
+static void __init omap_apollon_map_io(void)
+{
+ omap2_map_common_io();
+}
+
+MACHINE_START(OMAP_APOLLON, "OMAP24xx Apollon")
+ /* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = omap_apollon_map_io,
+ .init_irq = omap_apollon_init_irq,
+ .init_machine = omap_apollon_init,
+ .timer = &omap_timer,
+MACHINE_END
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
+#include <linux/workqueue.h>
+#include <linux/input.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/flash.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/gpioexpander.h>
#include <asm/arch/mux.h>
#include <asm/arch/usb.h>
+#include <asm/arch/irda.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
-#include <asm/arch/prcm.h>
+#include <asm/arch/keypad.h>
+#include <asm/arch/menelaus.h>
+#include <asm/arch/dma.h>
+#include "prcm-regs.h"
#include <asm/io.h>
#include <asm/delay.h>
+static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
+static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
+
+static int h4_keymap[] = {
+ KEY(0, 0, KEY_LEFT),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_A),
+ KEY(0, 3, KEY_B),
+ KEY(0, 4, KEY_C),
+ KEY(1, 0, KEY_DOWN),
+ KEY(1, 1, KEY_UP),
+ KEY(1, 2, KEY_E),
+ KEY(1, 3, KEY_F),
+ KEY(1, 4, KEY_G),
+ KEY(2, 0, KEY_ENTER),
+ KEY(2, 1, KEY_I),
+ KEY(2, 2, KEY_J),
+ KEY(2, 3, KEY_K),
+ KEY(2, 4, KEY_3),
+ KEY(3, 0, KEY_M),
+ KEY(3, 1, KEY_N),
+ KEY(3, 2, KEY_O),
+ KEY(3, 3, KEY_P),
+ KEY(3, 4, KEY_Q),
+ KEY(4, 0, KEY_R),
+ KEY(4, 1, KEY_4),
+ KEY(4, 2, KEY_T),
+ KEY(4, 3, KEY_U),
+ KEY(4, 4, KEY_ENTER),
+ KEY(5, 0, KEY_V),
+ KEY(5, 1, KEY_W),
+ KEY(5, 2, KEY_L),
+ KEY(5, 3, KEY_S),
+ KEY(5, 4, KEY_ENTER),
+ 0
+};
+
static struct mtd_partition h4_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.resource = h4_smc91x_resources,
};
+/* Select between the IrDA and aGPS module
+ */
+static int h4_select_irda(struct device *dev, int state)
+{
+ unsigned char expa;
+ int err = 0;
+
+ if ((err = read_gpio_expa(&expa, 0x21))) {
+ printk(KERN_ERR "Error reading from I/O expander\n");
+ return err;
+ }
+
+ /* 'P6' enable/disable IRDA_TX and IRDA_RX */
+ if (state & IR_SEL) { /* IrDa */
+ if ((err = write_gpio_expa(expa | 0x01, 0x21))) {
+ printk(KERN_ERR "Error writing to I/O expander\n");
+ return err;
+ }
+ } else {
+ if ((err = write_gpio_expa(expa & ~0x01, 0x21))) {
+ printk(KERN_ERR "Error writing to I/O expander\n");
+ return err;
+ }
+ }
+ return err;
+}
+
+static void set_trans_mode(void *data)
+{
+ int *mode = data;
+ unsigned char expa;
+ int err = 0;
+
+ if ((err = read_gpio_expa(&expa, 0x20)) != 0) {
+ printk(KERN_ERR "Error reading from I/O expander\n");
+ }
+
+ expa &= ~0x01;
+
+ if (!(*mode & IR_SIRMODE)) { /* MIR/FIR */
+ expa |= 0x01;
+ }
+
+ if ((err = write_gpio_expa(expa, 0x20)) != 0) {
+ printk(KERN_ERR "Error writing to I/O expander\n");
+ }
+}
+
+static int h4_transceiver_mode(struct device *dev, int mode)
+{
+ struct omap_irda_config *irda_config = dev->platform_data;
+
+ cancel_delayed_work(&irda_config->gpio_expa);
+ PREPARE_WORK(&irda_config->gpio_expa, set_trans_mode, &mode);
+ schedule_work(&irda_config->gpio_expa);
+
+ return 0;
+}
+
+static struct omap_irda_config h4_irda_data = {
+ .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
+ .transceiver_mode = h4_transceiver_mode,
+ .select_irda = h4_select_irda,
+ .rx_channel = OMAP24XX_DMA_UART3_RX,
+ .tx_channel = OMAP24XX_DMA_UART3_TX,
+ .dest_start = OMAP_UART3_BASE,
+ .src_start = OMAP_UART3_BASE,
+ .tx_trigger = OMAP24XX_DMA_UART3_TX,
+ .rx_trigger = OMAP24XX_DMA_UART3_RX,
+};
+
+static struct resource h4_irda_resources[] = {
+ [0] = {
+ .start = INT_24XX_UART3_IRQ,
+ .end = INT_24XX_UART3_IRQ,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device h4_irda_device = {
+ .name = "omapirda",
+ .id = -1,
+ .dev = {
+ .platform_data = &h4_irda_data,
+ },
+ .num_resources = 1,
+ .resource = h4_irda_resources,
+};
+
+static struct omap_kp_platform_data h4_kp_data = {
+ .rows = 6,
+ .cols = 7,
+ .keymap = h4_keymap,
+ .rep = 1,
+ .row_gpios = row_gpios,
+ .col_gpios = col_gpios,
+};
+
+static struct platform_device h4_kp_device = {
+ .name = "omap-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &h4_kp_data,
+ },
+};
+
+static struct platform_device h4_lcd_device = {
+ .name = "lcd_h4",
+ .id = -1,
+};
+
static struct platform_device *h4_devices[] __initdata = {
&h4_smc91x_device,
&h4_flash_device,
+ &h4_irda_device,
+ &h4_kp_device,
+ &h4_lcd_device,
};
static inline void __init h4_init_smc91x(void)
};
static struct omap_lcd_config h4_lcd_config __initdata = {
- .panel_name = "h4",
.ctrl_name = "internal",
};
* You have to mux them off in device drivers later on
* if not needed.
*/
+#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
+ omap_cfg_reg(K15_24XX_UART3_TX);
+ omap_cfg_reg(K14_24XX_UART3_RX);
+#endif
+
+#if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE)
+ if (omap_has_menelaus()) {
+ row_gpios[5] = 0;
+ col_gpios[2] = 15;
+ col_gpios[6] = 18;
+ }
+#endif
+
platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
omap_board_config = h4_config;
omap_board_config_size = ARRAY_SIZE(h4_config);
#endif
+#if defined(CONFIG_OMAP_STI)
+
+#define OMAP2_STI_BASE IO_ADDRESS(0x48068000)
+#define OMAP2_STI_CHANNEL_BASE 0x54000000
+#define OMAP2_STI_IRQ 4
+
+static struct resource sti_resources[] = {
+ {
+ .start = OMAP2_STI_BASE,
+ .end = OMAP2_STI_BASE + 0x7ff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP2_STI_CHANNEL_BASE,
+ .end = OMAP2_STI_CHANNEL_BASE + SZ_64K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP2_STI_IRQ,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device sti_device = {
+ .name = "sti",
+ .id = -1,
+ .dev = {
+ .release = omap_nop_release,
+ },
+ .num_resources = ARRAY_SIZE(sti_resources),
+ .resource = sti_resources,
+};
+
+static inline void omap_init_sti(void)
+{
+ platform_device_register(&sti_device);
+}
+#else
+static inline void omap_init_sti(void) {}
+#endif
+
/*-------------------------------------------------------------------------*/
static int __init omap2_init_devices(void)
* in alphabetical order so they're easier to sort through.
*/
omap_init_i2c();
+ omap_init_sti();
return 0;
}
#include <asm/arch/board.h>
#include <asm/arch/mux.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/menelaus.h>
void omap_nop_release(struct device *dev)
#endif
/*-------------------------------------------------------------------------*/
+#if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE)
+
+static void omap_init_kp(void)
+{
+ if (machine_is_omap_h2() || machine_is_omap_h3()) {
+ omap_cfg_reg(F18_1610_KBC0);
+ omap_cfg_reg(D20_1610_KBC1);
+ omap_cfg_reg(D19_1610_KBC2);
+ omap_cfg_reg(E18_1610_KBC3);
+ omap_cfg_reg(C21_1610_KBC4);
+
+ omap_cfg_reg(G18_1610_KBR0);
+ omap_cfg_reg(F19_1610_KBR1);
+ omap_cfg_reg(H14_1610_KBR2);
+ omap_cfg_reg(E20_1610_KBR3);
+ omap_cfg_reg(E19_1610_KBR4);
+ omap_cfg_reg(N19_1610_KBR5);
+ } else if (machine_is_omap_perseus2()) {
+ omap_cfg_reg(E2_730_KBR0);
+ omap_cfg_reg(J7_730_KBR1);
+ omap_cfg_reg(E1_730_KBR2);
+ omap_cfg_reg(F3_730_KBR3);
+ omap_cfg_reg(D2_730_KBR4);
+
+ omap_cfg_reg(C2_730_KBC0);
+ omap_cfg_reg(D3_730_KBC1);
+ omap_cfg_reg(E4_730_KBC2);
+ omap_cfg_reg(F4_730_KBC3);
+ omap_cfg_reg(E3_730_KBC4);
+ } else if (machine_is_omap_h4()) {
+ omap_cfg_reg(T19_24XX_KBR0);
+ omap_cfg_reg(R19_24XX_KBR1);
+ omap_cfg_reg(V18_24XX_KBR2);
+ omap_cfg_reg(M21_24XX_KBR3);
+ omap_cfg_reg(E5__24XX_KBR4);
+ if (omap_has_menelaus()) {
+ omap_cfg_reg(B3__24XX_KBR5);
+ omap_cfg_reg(AA4_24XX_KBC2);
+ omap_cfg_reg(B13_24XX_KBC6);
+ } else {
+ omap_cfg_reg(M18_24XX_KBR5);
+ omap_cfg_reg(H19_24XX_KBC2);
+ omap_cfg_reg(N19_24XX_KBC6);
+ }
+ omap_cfg_reg(R20_24XX_KBC0);
+ omap_cfg_reg(M14_24XX_KBC1);
+ omap_cfg_reg(V17_24XX_KBC3);
+ omap_cfg_reg(P21_24XX_KBC4);
+ omap_cfg_reg(L14_24XX_KBC5);
+ }
+}
+#else
+static inline void omap_init_kp(void) {}
+#endif
+
+/*-------------------------------------------------------------------------*/
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
static inline void omap_init_mmc(void) {}
#endif
+/*-------------------------------------------------------------------------*/
+
+/* Numbering for the SPI-capable controllers when used for SPI:
+ * spi = 1
+ * uwire = 2
+ * mmc1..2 = 3..4
+ * mcbsp1..3 = 5..7
+ */
+
+#if defined(CONFIG_SPI_OMAP_UWIRE) || defined(CONFIG_SPI_OMAP_UWIRE_MODULE)
+
+#define OMAP_UWIRE_BASE 0xfffb3000
+
+static struct resource uwire_resources[] = {
+ {
+ .start = OMAP_UWIRE_BASE,
+ .end = OMAP_UWIRE_BASE + 0x20,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device omap_uwire_device = {
+ .name = "omap_uwire",
+ .id = -1,
+ .dev = {
+ .release = omap_nop_release,
+ },
+ .num_resources = ARRAY_SIZE(uwire_resources),
+ .resource = uwire_resources,
+};
+
+static void omap_init_uwire(void)
+{
+ /* FIXME define and use a boot tag; not all boards will be hooking
+ * up devices to the microwire controller, and multi-board configs
+ * mean that CONFIG_SPI_OMAP_UWIRE may be configured anyway...
+ */
+
+ /* board-specific code must configure chipselects (only a few
+ * are normally used) and SCLK/SDI/SDO (each has two choices).
+ */
+ (void) platform_device_register(&omap_uwire_device);
+}
+#else
+static inline void omap_init_uwire(void) {}
+#endif
+
+/*-------------------------------------------------------------------------*/
+
#if defined(CONFIG_OMAP_WATCHDOG) || defined(CONFIG_OMAP_WATCHDOG_MODULE)
#ifdef CONFIG_ARCH_OMAP24XX
static inline void omap_init_rng(void) {}
#endif
-#if defined(CONFIG_FB_OMAP) || defined(CONFIG_FB_OMAP_MODULE)
-
-static struct omap_lcd_config omap_fb_conf;
-
-static u64 omap_fb_dma_mask = ~(u32)0;
-
-static struct platform_device omap_fb_device = {
- .name = "omapfb",
- .id = -1,
- .dev = {
- .release = omap_nop_release,
- .dma_mask = &omap_fb_dma_mask,
- .coherent_dma_mask = ~(u32)0,
- .platform_data = &omap_fb_conf,
- },
- .num_resources = 0,
-};
-
-static inline void omap_init_fb(void)
-{
- const struct omap_lcd_config *conf;
-
- conf = omap_get_config(OMAP_TAG_LCD, struct omap_lcd_config);
- if (conf != NULL)
- omap_fb_conf = *conf;
- platform_device_register(&omap_fb_device);
-}
-
-#else
-
-static inline void omap_init_fb(void) {}
-
-#endif
-
/*
* This gets called after board-specific INIT_MACHINE, and initializes most
* on-chip peripherals accessible on this board (except for few like USB):
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
- omap_init_fb();
omap_init_i2c();
+ omap_init_kp();
omap_init_mmc();
+ omap_init_uwire();
omap_init_wdt();
omap_init_rng();
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-omap/board-ams-delta.h
+ *
+ * Copyright (C) 2006 Jonathan McDowell <noodles@earth.li>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#ifndef __ASM_ARCH_OMAP_AMS_DELTA_H
+#define __ASM_ARCH_OMAP_AMS_DELTA_H
+
+#if defined (CONFIG_MACH_AMS_DELTA)
+
+#define AMS_DELTA_LATCH1_PHYS 0x01000000
+#define AMS_DELTA_LATCH1_VIRT 0xEA000000
+#define AMS_DELTA_MODEM_PHYS 0x04000000
+#define AMS_DELTA_MODEM_VIRT 0xEB000000
+#define AMS_DELTA_LATCH2_PHYS 0x08000000
+#define AMS_DELTA_LATCH2_VIRT 0xEC000000
+
+#define AMS_DELTA_LATCH1_LED_CAMERA 0x01
+#define AMS_DELTA_LATCH1_LED_ADVERT 0x02
+#define AMS_DELTA_LATCH1_LED_EMAIL 0x04
+#define AMS_DELTA_LATCH1_LED_HANDSFREE 0x08
+#define AMS_DELTA_LATCH1_LED_VOICEMAIL 0x10
+#define AMS_DELTA_LATCH1_LED_VOICE 0x20
+
+#define AMS_DELTA_LATCH2_LCD_VBLEN 0x0001
+#define AMS_DELTA_LATCH2_LCD_NDISP 0x0002
+#define AMS_DELTA_LATCH2_NAND_NCE 0x0004
+#define AMS_DELTA_LATCH2_NAND_NRE 0x0008
+#define AMS_DELTA_LATCH2_NAND_NWP 0x0010
+#define AMS_DELTA_LATCH2_NAND_NWE 0x0020
+#define AMS_DELTA_LATCH2_NAND_ALE 0x0040
+#define AMS_DELTA_LATCH2_NAND_CLE 0x0080
+#define AMS_DELTA_LATCH2_MODEM_NRESET 0x1000
+#define AMS_DELTA_LATCH2_MODEM_CODEC 0x2000
+
+#define AMS_DELTA_GPIO_PIN_NAND_RB 12
+
+#ifndef __ASSEMBLY__
+void ams_delta_latch1_write(u8 mask, u8 value);
+void ams_delta_latch2_write(u16 mask, u16 value);
+#endif
+
+#endif /* CONFIG_MACH_AMS_DELTA */
+
+#endif /* __ASM_ARCH_OMAP_AMS_DELTA_H */
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-omap/board-apollon.h
+ *
+ * Hardware definitions for Samsung OMAP24XX Apollon board.
+ *
+ * Initial creation by Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ASM_ARCH_OMAP_APOLLON_H
+#define __ASM_ARCH_OMAP_APOLLON_H
+
+/* Placeholder for APOLLON specific defines */
+/* GPMC CS0 */
+#define APOLLON_CS0_BASE 0x00000000
+/* GPMC CS1 */
+#define APOLLON_CS1_BASE 0x08000000
+#define APOLLON_ETHR_START (APOLLON_CS1_BASE + 0x300)
+#define APOLLON_ETHR_GPIO_IRQ 74
+/* GPMC CS2 - reserved for OneNAND */
+#define APOLLON_CS2_BASE 0x10000000
+/* GPMC CS3 - reserved for NOR or NAND */
+#define APOLLON_CS3_BASE 0x18000000
+
+#endif /* __ASM_ARCH_OMAP_APOLLON_H */
+
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
#define OMAP1610_ETHR_START 0x04000300
-/* Samsung NAND flash at CS2B or CS3(NAND Boot) */
-#define OMAP_NAND_FLASH_START1 0x0A000000 /* CS2B */
-#define OMAP_NAND_FLASH_START2 0x0C000000 /* CS3 */
-
#endif /* __ASM_ARCH_OMAP_H2_H */
/* In OMAP1710 H3 the Ethernet is directly connected to CS1 */
#define OMAP1710_ETHR_START 0x04000300
-/* Samsung NAND flash at CS2B or CS3(NAND Boot) */
-#define OMAP_NAND_FLASH_START1 0x0A000000 /* CS2B */
-#define OMAP_NAND_FLASH_START2 0x0C000000 /* CS3 */
-
#define MAXIRQNUM (IH_BOARD_BASE)
#define MAXFIQNUM MAXIRQNUM
#define MAXSWINUM MAXIRQNUM
/* GPMC CS1 */
#define OMAP24XX_ETHR_START 0x08000300
#define OMAP24XX_ETHR_GPIO_IRQ 92
-
-#define H4_CS0_BASE 0x04000000
-
-#define H4_CS0_BASE 0x04000000
-
-#define H4_CS0_BASE 0x04000000
-
+#define H4_CS0_BASE 0x04000000
#endif /* __ASM_ARCH_OMAP_H4_H */
+++ /dev/null
-/*
- * Copyright (C) 2004 2N Telekomunikace, Ladislav Michl <michl@2n.cz>
- *
- * Hardware definitions for OMAP5910 based NetStar board.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_NETSTAR_H
-#define __ASM_ARCH_NETSTAR_H
-
-#include <asm/arch/tc.h>
-
-#define OMAP_NAND_FLASH_START1 OMAP_CS1_PHYS + (1 << 23)
-#define OMAP_NAND_FLASH_START2 OMAP_CS1_PHYS + (2 << 23)
-
-#endif /* __ASM_ARCH_NETSTAR_H */
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-omap/board-nokia.h
+ *
+ * Information structures for Nokia-specific board config data
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ */
+
+#ifndef _OMAP_BOARD_NOKIA_H
+#define _OMAP_BOARD_NOKIA_H
+
+#include <linux/types.h>
+
+#define OMAP_TAG_NOKIA_BT 0x4e01
+#define OMAP_TAG_WLAN_CX3110X 0x4e02
+#define OMAP_TAG_CBUS 0x4e03
+#define OMAP_TAG_EM_ASIC_BB5 0x4e04
+
+
+#define BT_CHIP_CSR 1
+#define BT_CHIP_TI 2
+
+#define BT_SYSCLK_12 1
+#define BT_SYSCLK_38_4 2
+
+struct omap_bluetooth_config {
+ u8 chip_type;
+ u8 bt_wakeup_gpio;
+ u8 host_wakeup_gpio;
+ u8 reset_gpio;
+ u8 bt_uart;
+ u8 bd_addr[6];
+ u8 bt_sysclk;
+};
+
+struct omap_wlan_cx3110x_config {
+ u8 chip_type;
+ s16 power_gpio;
+ s16 irq_gpio;
+ s16 spi_cs_gpio;
+};
+
+struct omap_cbus_config {
+ s16 clk_gpio;
+ s16 dat_gpio;
+ s16 sel_gpio;
+};
+
+struct omap_em_asic_bb5_config {
+ s16 retu_irq_gpio;
+ s16 tahvo_irq_gpio;
+};
+
+#endif
#define NR_IRQS (MAXIRQNUM + 1)
-/* Samsung NAND flash at CS2B or CS3(NAND Boot) */
-#define OMAP_NAND_FLASH_START1 0x0A000000 /* CS2B */
-#define OMAP_NAND_FLASH_START2 0x0C000000 /* CS3 */
-
#endif
#define OMAP_TAG_LCD 0x4f05
#define OMAP_TAG_GPIO_SWITCH 0x4f06
#define OMAP_TAG_UART 0x4f07
+#define OMAP_TAG_FBMEM 0x4f08
+#define OMAP_TAG_STI_CONSOLE 0x4f09
#define OMAP_TAG_BOOT_REASON 0x4f80
#define OMAP_TAG_FLASH_PART 0x4f81
+#define OMAP_TAG_VERSION_STR 0x4f82
struct omap_clock_config {
/* 0 for 12 MHz, 1 for 13 MHz and 2 for 19.2 MHz */
u32 console_speed;
};
+struct omap_sti_console_config {
+ unsigned enable:1;
+ u8 channel;
+};
+
struct omap_usb_config {
/* Configure drivers according to the connectors on your board:
* - "A" connector (rectagular)
char ctrl_name[16];
};
+struct omap_fbmem_config {
+ u32 fb_sram_start;
+ u32 fb_sram_size;
+ u32 fb_sdram_start;
+ u32 fb_sdram_size;
+};
+
/* Cover:
* high -> closed
* low -> open
int key_code:24; /* Linux key code */
};
+struct omap_uart_config {
+ /* Bit field of UARTs present; bit 0 --> UART1 */
+ unsigned int enabled_uarts;
+};
+
+
struct omap_flash_part_config {
char part_table[0];
};
char reason_str[12];
};
-struct omap_uart_config {
- /* Bit field of UARTs present; bit 0 --> UART1 */
- unsigned int enabled_uarts;
+struct omap_version_config {
+ char component[12];
+ char version[12];
};
+
+#include <asm-arm/arch-omap/board-nokia.h>
+
struct omap_board_config_entry {
u16 tag;
u16 len;
#include "board-h4.h"
#endif
+#ifdef CONFIG_MACH_OMAP_APOLLON
+#include "board-apollon.h"
+#endif
+
#ifdef CONFIG_MACH_OMAP_OSK
#include "board-osk.h"
#endif
#include "board-voiceblue.h"
#endif
-#ifdef CONFIG_MACH_NETSTAR
-#include "board-netstar.h"
-#endif
-
#endif /* !__ASSEMBLER__ */
#endif /* __ASM_ARCH_OMAP_HARDWARE_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff