spi: move common spi_setup() functionality into core

Start moving some spi_setup() functionality into the SPI core from the
various spi_master controller drivers:

 - Make that function stop being an inline;

 - Move two common idioms from drivers into that new function:
    * Default bits_per_word to 8 if that field isn't set
    * Issue a standardized dev_dbg() message

This is a net minor source code shrink, and supports enhancments found in
some follow-up patches.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

diff --git a/drivers/spi/atmel_spi.c b/drivers/spi/atmel_spi.c
index 12e443c..9f9ff3a 100644 (file)
--- a/drivers/spi/atmel_spi.c
+++ b/drivers/spi/atmel_spi.c
@@ -555,8 +555,6 @@ static int atmel_spi_setup(struct spi_device *spi)
                return -EINVAL;
        }
 
-       if (bits == 0)
-               bits = 8;
        if (bits < 8 || bits > 16) {
                dev_dbg(&spi->dev,
                                "setup: invalid bits_per_word %u (8 to 16)\n",

diff --git a/drivers/spi/au1550_spi.c b/drivers/spi/au1550_spi.c
index b02f25c..6a407e6 100644 (file)
--- a/drivers/spi/au1550_spi.c
+++ b/drivers/spi/au1550_spi.c
@@ -291,8 +291,6 @@ static int au1550_spi_setup(struct spi_device *spi)
 {
        struct au1550_spi *hw = spi_master_get_devdata(spi->master);
 
-       if (spi->bits_per_word == 0)
-               spi->bits_per_word = 8;
        if (spi->bits_per_word < 4 || spi->bits_per_word > 24) {
                dev_err(&spi->dev, "setup: invalid bits_per_word=%d\n",
                        spi->bits_per_word);

diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index d6d0c5d..b4f3b75 100644 (file)
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -619,9 +619,7 @@ static int omap2_mcspi_setup(struct spi_device *spi)
                return -EINVAL;
        }
 
-       if (spi->bits_per_word == 0)
-               spi->bits_per_word = 8;
-       else if (spi->bits_per_word < 4 || spi->bits_per_word > 32) {
+       if (spi->bits_per_word < 4 || spi->bits_per_word > 32) {
                dev_dbg(&spi->dev, "setup: unsupported %d bit words\n",
                        spi->bits_per_word);
                return -EINVAL;

diff --git a/drivers/spi/omap_uwire.c b/drivers/spi/omap_uwire.c
index fe8b9ac..747d29b 100644 (file)
--- a/drivers/spi/omap_uwire.c
+++ b/drivers/spi/omap_uwire.c
@@ -339,8 +339,6 @@ static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
        bits = spi->bits_per_word;
        if (t != NULL && t->bits_per_word)
                bits = t->bits_per_word;
-       if (!bits)
-               bits = 8;
 
        if (bits > 16) {
                pr_debug("%s: wordsize %d?\n", dev_name(&spi->dev), bits);

diff --git a/drivers/spi/orion_spi.c b/drivers/spi/orion_spi.c
index c8b0bab..6d5e33b 100644 (file)
--- a/drivers/spi/orion_spi.c
+++ b/drivers/spi/orion_spi.c
@@ -369,9 +369,6 @@ static int orion_spi_setup(struct spi_device *spi)
                orion_spi_setbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
                                  (1 << 14));
 
-       if (spi->bits_per_word == 0)
-               spi->bits_per_word = 8;
-
        if ((spi->max_speed_hz == 0)
                        || (spi->max_speed_hz > orion_spi->max_speed))
                spi->max_speed_hz = orion_spi->max_speed;

diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 3f3c08c..c7365e0 100644 (file)
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -1236,9 +1236,6 @@ static int setup(struct spi_device *spi)
        uint tx_thres = TX_THRESH_DFLT;
        uint rx_thres = RX_THRESH_DFLT;
 
-       if (!spi->bits_per_word)
-               spi->bits_per_word = 8;
-
        if (drv_data->ssp_type != PXA25x_SSP
                && (spi->bits_per_word < 4 || spi->bits_per_word > 32)) {
                dev_err(&spi->dev, "failed setup: ssp_type=%d, bits/wrd=%d "
@@ -1328,18 +1325,14 @@ static int setup(struct spi_device *spi)
 
        /* NOTE:  PXA25x_SSP _could_ use external clocking ... */
        if (drv_data->ssp_type != PXA25x_SSP)
-               dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d, %s\n",
-                               spi->bits_per_word,
+               dev_dbg(&spi->dev, "%ld Hz actual, %s\n",
                                clk_get_rate(ssp->clk)
                                        / (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
-                               spi->mode & 0x3,
                                chip->enable_dma ? "DMA" : "PIO");
        else
-               dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d, %s\n",
-                               spi->bits_per_word,
+               dev_dbg(&spi->dev, "%ld Hz actual, %s\n",
                                clk_get_rate(ssp->clk) / 2
                                        / (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
-                               spi->mode & 0x3,
                                chip->enable_dma ? "DMA" : "PIO");
 
        if (spi->bits_per_word <= 8) {

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 8eba98c..0276bc3 100644 (file)
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -265,7 +265,7 @@ int spi_add_device(struct spi_device *spi)
         * normally rely on the device being setup.  Devices
         * using SPI_CS_HIGH can't coexist well otherwise...
         */
-       status = spi->master->setup(spi);
+       status = spi_setup(spi);
        if (status < 0) {
                dev_err(dev, "can't %s %s, status %d\n",
                                "setup", dev_name(&spi->dev), status);
@@ -583,6 +583,59 @@ EXPORT_SYMBOL_GPL(spi_busnum_to_master);
 
 /*-------------------------------------------------------------------------*/
 
+/* Core methods for SPI master protocol drivers.  Some of the
+ * other core methods are currently defined as inline functions.
+ */
+
+/**
+ * spi_setup - setup SPI mode and clock rate
+ * @spi: the device whose settings are being modified
+ * Context: can sleep, and no requests are queued to the device
+ *
+ * SPI protocol drivers may need to update the transfer mode if the
+ * device doesn't work with its default.  They may likewise need
+ * to update clock rates or word sizes from initial values.  This function
+ * changes those settings, and must be called from a context that can sleep.
+ * Except for SPI_CS_HIGH, which takes effect immediately, the changes take
+ * effect the next time the device is selected and data is transferred to
+ * or from it.  When this function returns, the spi device is deselected.
+ *
+ * Note that this call will fail if the protocol driver specifies an option
+ * that the underlying controller or its driver does not support.  For
+ * example, not all hardware supports wire transfers using nine bit words,
+ * LSB-first wire encoding, or active-high chipselects.
+ */
+int spi_setup(struct spi_device *spi)
+{
+       int             status;
+
+       if (!spi->bits_per_word)
+               spi->bits_per_word = 8;
+
+       status = spi->master->setup(spi);
+
+       dev_dbg(&spi->dev, "setup mode %d, %s%s%s%s"
+                               "%u bits/w, %u Hz max --> %d\n",
+                       (int) (spi->mode & (SPI_CPOL | SPI_CPHA)),
+                       (spi->mode & SPI_CS_HIGH) ? "cs_high, " : "",
+                       (spi->mode & SPI_LSB_FIRST) ? "lsb, " : "",
+                       (spi->mode & SPI_3WIRE) ? "3wire, " : "",
+                       (spi->mode & SPI_LOOP) ? "loopback, " : "",
+                       spi->bits_per_word, spi->max_speed_hz,
+                       status);
+
+       return status;
+}
+EXPORT_SYMBOL_GPL(spi_setup);
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Utility methods for SPI master protocol drivers, layered on
+ * top of the core.  Some other utility methods are defined as
+ * inline functions.
+ */
+
 static void spi_complete(void *arg)
 {
        complete(arg);

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 2e5fd09..d54058a 100644 (file)
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1016,10 +1016,6 @@ static int bfin_spi_setup(struct spi_device *spi)
                return -EINVAL;
        }
 
-       /* Zero (the default) here means 8 bits */
-       if (!spi->bits_per_word)
-               spi->bits_per_word = 8;
-
        if (spi->bits_per_word != 8 && spi->bits_per_word != 16)
                return -EINVAL;
 

diff --git a/drivers/spi/spi_bitbang.c b/drivers/spi/spi_bitbang.c
index 85e61f4..855b0b0 100644 (file)
--- a/drivers/spi/spi_bitbang.c
+++ b/drivers/spi/spi_bitbang.c
@@ -201,9 +201,6 @@ int spi_bitbang_setup(struct spi_device *spi)
                spi->controller_state = cs;
        }
 
-       if (!spi->bits_per_word)
-               spi->bits_per_word = 8;
-
        /* per-word shift register access, in hardware or bitbanging */
        cs->txrx_word = bitbang->txrx_word[spi->mode & (SPI_CPOL|SPI_CPHA)];
        if (!cs->txrx_word)
@@ -213,9 +210,7 @@ int spi_bitbang_setup(struct spi_device *spi)
        if (retval < 0)
                return retval;
 
-       dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
-                       __func__, spi->mode & (SPI_CPOL | SPI_CPHA),
-                       spi->bits_per_word, 2 * cs->nsecs);
+       dev_dbg(&spi->dev, "%s, %u nsec/bit\n", __func__, 2 * cs->nsecs);
 
        /* NOTE we _need_ to call chipselect() early, ideally with adapter
         * setup, unless the hardware defaults cooperate to avoid confusion

diff --git a/drivers/spi/spi_imx.c b/drivers/spi/spi_imx.c
index 0671aee..26d5ef0 100644 (file)
--- a/drivers/spi/spi_imx.c
+++ b/drivers/spi/spi_imx.c
@@ -1286,10 +1286,7 @@ static int setup(struct spi_device *spi)
 
        /* SPI word width */
        tmp = spi->bits_per_word;
-       if (tmp == 0) {
-               tmp = 8;
-               spi->bits_per_word = 8;
-       } else if (tmp > 16) {
+       if (tmp > 16) {
                status = -EINVAL;
                dev_err(&spi->dev,
                        "setup - "

diff --git a/drivers/spi/spi_mpc83xx.c b/drivers/spi/spi_mpc83xx.c
index a32ccb4..0926a3e 100644 (file)
--- a/drivers/spi/spi_mpc83xx.c
+++ b/drivers/spi/spi_mpc83xx.c
@@ -447,9 +447,6 @@ static int mpc83xx_spi_setup(struct spi_device *spi)
        }
        mpc83xx_spi = spi_master_get_devdata(spi->master);
 
-       if (!spi->bits_per_word)
-               spi->bits_per_word = 8;
-
        hw_mode = cs->hw_mode; /* Save orginal settings */
        cs->hw_mode = mpc83xx_spi_read_reg(&mpc83xx_spi->base->mode);
        /* mask out bits we are going to set */
@@ -471,9 +468,6 @@ static int mpc83xx_spi_setup(struct spi_device *spi)
                return retval;
        }
 
-       dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u Hz\n",
-               __func__, spi->mode & (SPI_CPOL | SPI_CPHA),
-               spi->bits_per_word, spi->max_speed_hz);
 #if 0 /* Don't think this is needed */
        /* NOTE we _need_ to call chipselect() early, ideally with adapter
         * setup, unless the hardware defaults cooperate to avoid confusion

diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c
index b3ebc1d..18a4c7f 100644 (file)
--- a/drivers/spi/spi_s3c24xx.c
+++ b/drivers/spi/spi_s3c24xx.c
@@ -153,9 +153,6 @@ static int s3c24xx_spi_setup(struct spi_device *spi)
 {
        int ret;
 
-       if (!spi->bits_per_word)
-               spi->bits_per_word = 8;
-
        if (spi->mode & ~MODEBITS) {
                dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
                        spi->mode & ~MODEBITS);
@@ -168,10 +165,6 @@ static int s3c24xx_spi_setup(struct spi_device *spi)
                return ret;
        }
 
-       dev_dbg(&spi->dev, "%s: mode %d, %u bpw, %d hz\n",
-               __func__, spi->mode, spi->bits_per_word,
-               spi->max_speed_hz);
-
        return 0;
 }
 

diff --git a/drivers/spi/spi_txx9.c b/drivers/spi/spi_txx9.c
index 29cbb06..8e36b21 100644 (file)
--- a/drivers/spi/spi_txx9.c
+++ b/drivers/spi/spi_txx9.c
@@ -126,7 +126,7 @@ static int txx9spi_setup(struct spi_device *spi)
                        || spi->max_speed_hz < c->min_speed_hz)
                return -EINVAL;
 
-       bits_per_word = spi->bits_per_word ? : 8;
+       bits_per_word = spi->bits_per_word;
        if (bits_per_word != 8 && bits_per_word != 16)
                return -EINVAL;
 

diff --git a/drivers/spi/xilinx_spi.c b/drivers/spi/xilinx_spi.c
index 494d3f7..2d7e6b8 100644 (file)
--- a/drivers/spi/xilinx_spi.c
+++ b/drivers/spi/xilinx_spi.c
@@ -170,9 +170,6 @@ static int xilinx_spi_setup(struct spi_device *spi)
        xspi = spi_master_get_devdata(spi->master);
        bitbang = &xspi->bitbang;
 
-       if (!spi->bits_per_word)
-               spi->bits_per_word = 8;
-
        if (spi->mode & ~MODEBITS) {
                dev_err(&spi->dev, "%s, unsupported mode bits %x\n",
                        __func__, spi->mode & ~MODEBITS);
@@ -183,9 +180,6 @@ static int xilinx_spi_setup(struct spi_device *spi)
        if (retval < 0)
                return retval;
 
-       dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
-               __func__, spi->mode & MODEBITS, spi->bits_per_word, 0);
-
        return 0;
 }
 

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index a0faa18..0db5d64 100644 (file)
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -523,30 +523,7 @@ static inline void spi_message_free(struct spi_message *m)
        kfree(m);
 }
 
-/**
- * spi_setup - setup SPI mode and clock rate
- * @spi: the device whose settings are being modified
- * Context: can sleep, and no requests are queued to the device
- *
- * SPI protocol drivers may need to update the transfer mode if the
- * device doesn't work with its default.  They may likewise need
- * to update clock rates or word sizes from initial values.  This function
- * changes those settings, and must be called from a context that can sleep.
- * Except for SPI_CS_HIGH, which takes effect immediately, the changes take
- * effect the next time the device is selected and data is transferred to
- * or from it.  When this function returns, the spi device is deselected.
- *
- * Note that this call will fail if the protocol driver specifies an option
- * that the underlying controller or its driver does not support.  For
- * example, not all hardware supports wire transfers using nine bit words,
- * LSB-first wire encoding, or active-high chipselects.
- */
-static inline int
-spi_setup(struct spi_device *spi)
-{
-       return spi->master->setup(spi);
-}
-
+extern int spi_setup(struct spi_device *spi);
 
 /**
  * spi_async - asynchronous SPI transfer