X-Git-Url: http://ftp.safe.ca/?p=safe%2Fjmp%2Flinux-2.6;a=blobdiff_plain;f=drivers%2Fata%2Fpata_it821x.c;h=5cb286fd839e62d6e4ecc51843f43a9ce4a80ea6;hp=e10816931b2fe72b25454e60e0ed7925e7ac50ed;hb=5a0e3ad6af8660be21ca98a971cd00f331318c05;hpb=5682ed33aae05d10a25c95633ef9d9c062825888 diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c index e108169..5cb286f 100644 --- a/drivers/ata/pata_it821x.c +++ b/drivers/ata/pata_it821x.c @@ -1,7 +1,7 @@ /* * pata_it821x.c - IT821x PATA for new ATA layer * (C) 2005 Red Hat Inc - * Alan Cox + * Alan Cox * (C) 2007 Bartlomiej Zolnierkiewicz * * based upon @@ -10,7 +10,7 @@ * * linux/drivers/ide/pci/it821x.c Version 0.09 December 2004 * - * Copyright (C) 2004 Red Hat + * Copyright (C) 2004 Red Hat * * May be copied or modified under the terms of the GNU General Public License * Based in part on the ITE vendor provided SCSI driver. @@ -75,12 +75,13 @@ #include #include #include +#include #include #include #define DRV_NAME "pata_it821x" -#define DRV_VERSION "0.3.8" +#define DRV_VERSION "0.4.2" struct it821x_dev { @@ -425,6 +426,8 @@ static unsigned int it821x_smart_qc_issue(struct ata_queued_cmd *qc) case ATA_CMD_WRITE_MULTI: case ATA_CMD_WRITE_MULTI_EXT: case ATA_CMD_ID_ATA: + case ATA_CMD_INIT_DEV_PARAMS: + case 0xFC: /* Internal 'report rebuild state' */ /* Arguably should just no-op this one */ case ATA_CMD_SET_FEATURES: return ata_sff_qc_issue(qc); @@ -463,24 +466,22 @@ static int it821x_smart_set_mode(struct ata_link *link, struct ata_device **unus { struct ata_device *dev; - ata_link_for_each_dev(dev, link) { - if (ata_dev_enabled(dev)) { - /* We don't really care */ - dev->pio_mode = XFER_PIO_0; - dev->dma_mode = XFER_MW_DMA_0; - /* We do need the right mode information for DMA or PIO - and this comes from the current configuration flags */ - if (ata_id_has_dma(dev->id)) { - ata_dev_printk(dev, KERN_INFO, "configured for DMA\n"); - dev->xfer_mode = XFER_MW_DMA_0; - dev->xfer_shift = ATA_SHIFT_MWDMA; - dev->flags &= ~ATA_DFLAG_PIO; - } else { - ata_dev_printk(dev, KERN_INFO, "configured for PIO\n"); - dev->xfer_mode = XFER_PIO_0; - dev->xfer_shift = ATA_SHIFT_PIO; - dev->flags |= ATA_DFLAG_PIO; - } + ata_for_each_dev(dev, link, ENABLED) { + /* We don't really care */ + dev->pio_mode = XFER_PIO_0; + dev->dma_mode = XFER_MW_DMA_0; + /* We do need the right mode information for DMA or PIO + and this comes from the current configuration flags */ + if (ata_id_has_dma(dev->id)) { + ata_dev_printk(dev, KERN_INFO, "configured for DMA\n"); + dev->xfer_mode = XFER_MW_DMA_0; + dev->xfer_shift = ATA_SHIFT_MWDMA; + dev->flags &= ~ATA_DFLAG_PIO; + } else { + ata_dev_printk(dev, KERN_INFO, "configured for PIO\n"); + dev->xfer_mode = XFER_PIO_0; + dev->xfer_shift = ATA_SHIFT_PIO; + dev->flags |= ATA_DFLAG_PIO; } } return 0; @@ -494,8 +495,6 @@ static int it821x_smart_set_mode(struct ata_link *link, struct ata_device **unus * special. In our case we need to lock the sector count to avoid * blowing the brains out of the firmware with large LBA48 requests * - * FIXME: When FUA appears we need to block FUA too. And SMART and - * basically we need to filter commands for this chip. */ static void it821x_dev_config(struct ata_device *adev) @@ -509,7 +508,7 @@ static void it821x_dev_config(struct ata_device *adev) if (strstr(model_num, "Integrated Technology Express")) { /* RAID mode */ - printk(KERN_INFO "IT821x %sRAID%d volume", + ata_dev_printk(adev, KERN_INFO, "%sRAID%d volume", adev->id[147]?"Bootable ":"", adev->id[129]); if (adev->id[129] != 1) @@ -519,37 +518,53 @@ static void it821x_dev_config(struct ata_device *adev) /* This is a controller firmware triggered funny, don't report the drive faulty! */ adev->horkage &= ~ATA_HORKAGE_DIAGNOSTIC; + /* No HPA in 'smart' mode */ + adev->horkage |= ATA_HORKAGE_BROKEN_HPA; } /** - * it821x_ident_hack - Hack identify data up - * @ap: Port + * it821x_read_id - Hack identify data up + * @adev: device to read + * @tf: proposed taskfile + * @id: buffer for returned ident data * - * Walk the devices on this firmware driven port and slightly + * Query the devices on this firmware driven port and slightly * mash the identify data to stop us and common tools trying to * use features not firmware supported. The firmware itself does * some masking (eg SMART) but not enough. - * - * This is a bit of an abuse of the cable method, but it is the - * only method called at the right time. We could modify the libata - * core specifically for ident hacking but while we have one offender - * it seems better to keep the fallout localised. */ -static int it821x_ident_hack(struct ata_port *ap) +static unsigned int it821x_read_id(struct ata_device *adev, + struct ata_taskfile *tf, u16 *id) { - struct ata_device *adev; - ata_link_for_each_dev(adev, &ap->link) { - if (ata_dev_enabled(adev)) { - adev->id[84] &= ~(1 << 6); /* No FUA */ - adev->id[85] &= ~(1 << 10); /* No HPA */ - adev->id[76] = 0; /* No NCQ/AN etc */ - } + unsigned int err_mask; + unsigned char model_num[ATA_ID_PROD_LEN + 1]; + + err_mask = ata_do_dev_read_id(adev, tf, id); + if (err_mask) + return err_mask; + ata_id_c_string(id, model_num, ATA_ID_PROD, sizeof(model_num)); + + id[83] &= ~(1 << 12); /* Cache flush is firmware handled */ + id[83] &= ~(1 << 13); /* Ditto for LBA48 flushes */ + id[84] &= ~(1 << 6); /* No FUA */ + id[85] &= ~(1 << 10); /* No HPA */ + id[76] = 0; /* No NCQ/AN etc */ + + if (strstr(model_num, "Integrated Technology Express")) { + /* Set feature bits the firmware neglects */ + id[49] |= 0x0300; /* LBA, DMA */ + id[83] &= 0x7FFF; + id[83] |= 0x4400; /* Word 83 is valid and LBA48 */ + id[86] |= 0x0400; /* LBA48 on */ + id[ATA_ID_MAJOR_VER] |= 0x1F; + /* Clear the serial number because it's different each boot + which breaks validation on resume */ + memset(&id[ATA_ID_SERNO], 0x20, ATA_ID_SERNO_LEN); } - return ata_cable_unknown(ap); + return err_mask; } - /** * it821x_check_atapi_dma - ATAPI DMA handler * @qc: Command we are about to issue @@ -577,6 +592,136 @@ static int it821x_check_atapi_dma(struct ata_queued_cmd *qc) return 0; } +/** + * it821x_display_disk - display disk setup + * @n: Device number + * @buf: Buffer block from firmware + * + * Produce a nice informative display of the device setup as provided + * by the firmware. + */ + +static void it821x_display_disk(int n, u8 *buf) +{ + unsigned char id[41]; + int mode = 0; + char *mtype = ""; + char mbuf[8]; + char *cbl = "(40 wire cable)"; + + static const char *types[5] = { + "RAID0", "RAID1" "RAID 0+1", "JBOD", "DISK" + }; + + if (buf[52] > 4) /* No Disk */ + return; + + ata_id_c_string((u16 *)buf, id, 0, 41); + + if (buf[51]) { + mode = ffs(buf[51]); + mtype = "UDMA"; + } else if (buf[49]) { + mode = ffs(buf[49]); + mtype = "MWDMA"; + } + + if (buf[76]) + cbl = ""; + + if (mode) + snprintf(mbuf, 8, "%5s%d", mtype, mode - 1); + else + strcpy(mbuf, "PIO"); + if (buf[52] == 4) + printk(KERN_INFO "%d: %-6s %-8s %s %s\n", + n, mbuf, types[buf[52]], id, cbl); + else + printk(KERN_INFO "%d: %-6s %-8s Volume: %1d %s %s\n", + n, mbuf, types[buf[52]], buf[53], id, cbl); + if (buf[125] < 100) + printk(KERN_INFO "%d: Rebuilding: %d%%\n", n, buf[125]); +} + +/** + * it821x_firmware_command - issue firmware command + * @ap: IT821x port to interrogate + * @cmd: command + * @len: length + * + * Issue firmware commands expecting data back from the controller. We + * use this to issue commands that do not go via the normal paths. Other + * commands such as 0xFC can be issued normally. + */ + +static u8 *it821x_firmware_command(struct ata_port *ap, u8 cmd, int len) +{ + u8 status; + int n = 0; + u16 *buf = kmalloc(len, GFP_KERNEL); + if (buf == NULL) { + printk(KERN_ERR "it821x_firmware_command: Out of memory\n"); + return NULL; + } + /* This isn't quite a normal ATA command as we are talking to the + firmware not the drives */ + ap->ctl |= ATA_NIEN; + iowrite8(ap->ctl, ap->ioaddr.ctl_addr); + ata_wait_idle(ap); + iowrite8(ATA_DEVICE_OBS, ap->ioaddr.device_addr); + iowrite8(cmd, ap->ioaddr.command_addr); + udelay(1); + /* This should be almost immediate but a little paranoia goes a long + way. */ + while(n++ < 10) { + status = ioread8(ap->ioaddr.status_addr); + if (status & ATA_ERR) { + kfree(buf); + printk(KERN_ERR "it821x_firmware_command: rejected\n"); + return NULL; + } + if (status & ATA_DRQ) { + ioread16_rep(ap->ioaddr.data_addr, buf, len/2); + return (u8 *)buf; + } + mdelay(1); + } + kfree(buf); + printk(KERN_ERR "it821x_firmware_command: timeout\n"); + return NULL; +} + +/** + * it821x_probe_firmware - firmware reporting/setup + * @ap: IT821x port being probed + * + * Probe the firmware of the controller by issuing firmware command + * 0xFA and analysing the returned data. + */ + +static void it821x_probe_firmware(struct ata_port *ap) +{ + u8 *buf; + int i; + + /* This is a bit ugly as we can't just issue a task file to a device + as this is controller magic */ + + buf = it821x_firmware_command(ap, 0xFA, 512); + + if (buf != NULL) { + printk(KERN_INFO "pata_it821x: Firmware %02X/%02X/%02X%02X\n", + buf[505], + buf[506], + buf[507], + buf[508]); + for (i = 0; i < 4; i++) + it821x_display_disk(i, buf + 128 * i); + kfree(buf); + } +} + + /** * it821x_port_start - port setup @@ -610,6 +755,8 @@ static int it821x_port_start(struct ata_port *ap) /* Long I/O's although allowed in LBA48 space cause the onboard firmware to enter the twighlight zone */ /* No ATAPI DMA in this mode either */ + if (ap->port_no == 0) + it821x_probe_firmware(ap); } /* Pull the current clocks from 0x50 */ if (conf & (1 << (1 + ap->port_no))) @@ -631,6 +778,25 @@ static int it821x_port_start(struct ata_port *ap) return 0; } +/** + * it821x_rdc_cable - Cable detect for RDC1010 + * @ap: port we are checking + * + * Return the RDC1010 cable type. Unlike the IT821x we know how to do + * this and can do host side cable detect + */ + +static int it821x_rdc_cable(struct ata_port *ap) +{ + u16 r40; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_word(pdev, 0x40, &r40); + if (r40 & (1 << (2 + ap->port_no))) + return ATA_CBL_PATA40; + return ATA_CBL_PATA80; +} + static struct scsi_host_template it821x_sht = { ATA_BMDMA_SHT(DRV_NAME), }; @@ -641,9 +807,10 @@ static struct ata_port_operations it821x_smart_port_ops = { .check_atapi_dma= it821x_check_atapi_dma, .qc_issue = it821x_smart_qc_issue, - .cable_detect = it821x_ident_hack, + .cable_detect = ata_cable_80wire, .set_mode = it821x_smart_set_mode, .dev_config = it821x_dev_config, + .read_id = it821x_read_id, .port_start = it821x_port_start, }; @@ -664,8 +831,29 @@ static struct ata_port_operations it821x_passthru_port_ops = { .port_start = it821x_port_start, }; +static struct ata_port_operations it821x_rdc_port_ops = { + .inherits = &ata_bmdma_port_ops, + + .check_atapi_dma= it821x_check_atapi_dma, + .sff_dev_select = it821x_passthru_dev_select, + .bmdma_start = it821x_passthru_bmdma_start, + .bmdma_stop = it821x_passthru_bmdma_stop, + .qc_issue = it821x_passthru_qc_issue, + + .cable_detect = it821x_rdc_cable, + .set_piomode = it821x_passthru_set_piomode, + .set_dmamode = it821x_passthru_set_dmamode, + + .port_start = it821x_port_start, +}; + static void it821x_disable_raid(struct pci_dev *pdev) { + /* Neither the RDC nor the IT8211 */ + if (pdev->vendor != PCI_VENDOR_ID_ITE || + pdev->device != PCI_DEVICE_ID_ITE_8212) + return; + /* Reset local CPU, and set BIOS not ready */ pci_write_config_byte(pdev, 0x5E, 0x01); @@ -688,17 +876,32 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) static const struct ata_port_info info_smart = { .flags = ATA_FLAG_SLAVE_POSS, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, .port_ops = &it821x_smart_port_ops }; static const struct ata_port_info info_passthru = { .flags = ATA_FLAG_SLAVE_POSS, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA6, .port_ops = &it821x_passthru_port_ops }; + static const struct ata_port_info info_rdc = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &it821x_rdc_port_ops + }; + static const struct ata_port_info info_rdc_11 = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + /* No UDMA */ + .port_ops = &it821x_rdc_port_ops + }; const struct ata_port_info *ppi[] = { NULL, NULL }; static char *mode[2] = { "pass through", "smart" }; @@ -707,22 +910,30 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) rc = pcim_enable_device(pdev); if (rc) return rc; + + if (pdev->vendor == PCI_VENDOR_ID_RDC) { + /* Deal with Vortex86SX */ + if (pdev->revision == 0x11) + ppi[0] = &info_rdc_11; + else + ppi[0] = &info_rdc; + } else { + /* Force the card into bypass mode if so requested */ + if (it8212_noraid) { + printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n"); + it821x_disable_raid(pdev); + } + pci_read_config_byte(pdev, 0x50, &conf); + conf &= 1; - /* Force the card into bypass mode if so requested */ - if (it8212_noraid) { - printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n"); - it821x_disable_raid(pdev); + printk(KERN_INFO DRV_NAME": controller in %s mode.\n", + mode[conf]); + if (conf == 0) + ppi[0] = &info_passthru; + else + ppi[0] = &info_smart; } - pci_read_config_byte(pdev, 0x50, &conf); - conf &= 1; - - printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]); - if (conf == 0) - ppi[0] = &info_passthru; - else - ppi[0] = &info_smart; - - return ata_pci_sff_init_one(pdev, ppi, &it821x_sht, NULL); + return ata_pci_sff_init_one(pdev, ppi, &it821x_sht, NULL, 0); } #ifdef CONFIG_PM @@ -745,6 +956,7 @@ static int it821x_reinit_one(struct pci_dev *pdev) static const struct pci_device_id it821x[] = { { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), }, { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), }, + { PCI_VDEVICE(RDC, PCI_DEVICE_ID_RDC_D1010), }, { }, };