#define _SCSI_SCSI_H
#include <linux/types.h>
+#include <scsi/scsi_cmnd.h>
/*
- * The maximum sg list length SCSI can cope with
- * (currently must be a power of 2 between 32 and 256)
+ * The maximum number of SG segments that we will put inside a
+ * scatterlist (unless chaining is used). Should ideally fit inside a
+ * single page, to avoid a higher order allocation. We could define this
+ * to SG_MAX_SINGLE_ALLOC to pack correctly at the highest order. The
+ * minimum value is 32
*/
-#define SCSI_MAX_PHYS_SEGMENTS MAX_PHYS_SEGMENTS
-
+#define SCSI_MAX_SG_SEGMENTS 128
/*
- * SCSI command lengths
+ * Like SCSI_MAX_SG_SEGMENTS, but for archs that have sg chaining. This limit
+ * is totally arbitrary, a setting of 2048 will get you at least 8mb ios.
*/
-
-extern const unsigned char scsi_command_size[8];
-#define COMMAND_SIZE(opcode) scsi_command_size[((opcode) >> 5) & 7]
+#ifdef ARCH_HAS_SG_CHAIN
+#define SCSI_MAX_SG_CHAIN_SEGMENTS 2048
+#else
+#define SCSI_MAX_SG_CHAIN_SEGMENTS SCSI_MAX_SG_SEGMENTS
+#endif
/*
- * SCSI device types
+ * Special value for scanning to specify scanning or rescanning of all
+ * possible channels, (target) ids, or luns on a given shost.
*/
-
-#define MAX_SCSI_DEVICE_CODE 15
-extern const char *const scsi_device_types[MAX_SCSI_DEVICE_CODE];
+#define SCAN_WILD_CARD ~0
/*
* SCSI opcodes
#define READ_TOC 0x43
#define LOG_SELECT 0x4c
#define LOG_SENSE 0x4d
+#define XDWRITEREAD_10 0x53
#define MODE_SELECT_10 0x55
#define RESERVE_10 0x56
#define RELEASE_10 0x57
#define MODE_SENSE_10 0x5a
#define PERSISTENT_RESERVE_IN 0x5e
#define PERSISTENT_RESERVE_OUT 0x5f
+#define VARIABLE_LENGTH_CMD 0x7f
#define REPORT_LUNS 0xa0
+#define MAINTENANCE_IN 0xa3
+#define MAINTENANCE_OUT 0xa4
#define MOVE_MEDIUM 0xa5
#define EXCHANGE_MEDIUM 0xa6
#define READ_12 0xa8
#define SERVICE_ACTION_IN 0x9e
/* values for service action in */
#define SAI_READ_CAPACITY_16 0x10
+/* values for maintenance in */
+#define MI_REPORT_TARGET_PGS 0x0a
+/* values for maintenance out */
+#define MO_SET_TARGET_PGS 0x0a
/* Values for T10/04-262r7 */
#define ATA_16 0x85 /* 16-byte pass-thru */
#define ATA_12 0xa1 /* 12-byte pass-thru */
/*
+ * SCSI command lengths
+ */
+
+#define SCSI_MAX_VARLEN_CDB_SIZE 260
+
+/* defined in T10 SCSI Primary Commands-2 (SPC2) */
+struct scsi_varlen_cdb_hdr {
+ u8 opcode; /* opcode always == VARIABLE_LENGTH_CMD */
+ u8 control;
+ u8 misc[5];
+ u8 additional_cdb_length; /* total cdb length - 8 */
+ __be16 service_action;
+ /* service specific data follows */
+};
+
+static inline unsigned
+scsi_varlen_cdb_length(const void *hdr)
+{
+ return ((struct scsi_varlen_cdb_hdr *)hdr)->additional_cdb_length + 8;
+}
+
+extern const unsigned char scsi_command_size_tbl[8];
+#define COMMAND_SIZE(opcode) scsi_command_size_tbl[((opcode) >> 5) & 7]
+
+static inline unsigned
+scsi_command_size(const unsigned char *cmnd)
+{
+ return (cmnd[0] == VARIABLE_LENGTH_CMD) ?
+ scsi_varlen_cdb_length(cmnd) : COMMAND_SIZE(cmnd[0]);
+}
+
+/*
* SCSI Architecture Model (SAM) Status codes. Taken from SAM-3 draft
* T10/1561-D Revision 4 Draft dated 7th November 2002.
*/
/*
* DEVICE TYPES
+ * Please keep them in 0x%02x format for $MODALIAS to work
*/
#define TYPE_DISK 0x00
#define TYPE_RBC 0x0e
#define TYPE_NO_LUN 0x7f
+/* SCSI protocols; these are taken from SPC-3 section 7.5 */
+enum scsi_protocol {
+ SCSI_PROTOCOL_FCP = 0, /* Fibre Channel */
+ SCSI_PROTOCOL_SPI = 1, /* parallel SCSI */
+ SCSI_PROTOCOL_SSA = 2, /* Serial Storage Architecture - Obsolete */
+ SCSI_PROTOCOL_SBP = 3, /* firewire */
+ SCSI_PROTOCOL_SRP = 4, /* Infiniband RDMA */
+ SCSI_PROTOCOL_ISCSI = 5,
+ SCSI_PROTOCOL_SAS = 6,
+ SCSI_PROTOCOL_ADT = 7, /* Media Changers */
+ SCSI_PROTOCOL_ATA = 8,
+ SCSI_PROTOCOL_UNSPEC = 0xf, /* No specific protocol */
+};
+
+/* Returns a human-readable name for the device */
+extern const char * scsi_device_type(unsigned type);
+
/*
* standard mode-select header prepended to all mode-select commands
*/
};
/*
+ * The Well Known LUNS (SAM-3) in our int representation of a LUN
+ */
+#define SCSI_W_LUN_BASE 0xc100
+#define SCSI_W_LUN_REPORT_LUNS (SCSI_W_LUN_BASE + 1)
+#define SCSI_W_LUN_ACCESS_CONTROL (SCSI_W_LUN_BASE + 2)
+#define SCSI_W_LUN_TARGET_LOG_PAGE (SCSI_W_LUN_BASE + 3)
+
+static inline int scsi_is_wlun(unsigned int lun)
+{
+ return (lun & 0xff00) == SCSI_W_LUN_BASE;
+}
+
+
+/*
* MESSAGE CODES
*/
#define SOFT_ERROR 0x2005
#define ADD_TO_MLQUEUE 0x2006
#define TIMEOUT_ERROR 0x2007
+#define SCSI_RETURN_NOT_HANDLED 0x2008
/*
* Midlevel queue return values.
#define driver_byte(result) (((result) >> 24) & 0xff)
#define suggestion(result) (driver_byte(result) & SUGGEST_MASK)
+static inline void set_msg_byte(struct scsi_cmnd *cmd, char status)
+{
+ cmd->result |= status << 8;
+}
+
+static inline void set_host_byte(struct scsi_cmnd *cmd, char status)
+{
+ cmd->result |= status << 16;
+}
+
+static inline void set_driver_byte(struct scsi_cmnd *cmd, char status)
+{
+ cmd->result |= status << 24;
+}
+
+
#define sense_class(sense) (((sense) >> 4) & 0x7)
#define sense_error(sense) ((sense) & 0xf)
#define sense_valid(sense) ((sense) & 0x80);
/* Used to obtain the PCI location of a device */
#define SCSI_IOCTL_GET_PCI 0x5387
+/* Pull a u32 out of a SCSI message (using BE SCSI conventions) */
+static inline __u32 scsi_to_u32(__u8 *ptr)
+{
+ return (ptr[0]<<24) + (ptr[1]<<16) + (ptr[2]<<8) + ptr[3];
+}
+
#endif /* _SCSI_SCSI_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff