*
* Copyright 2002-2005, Devicescape Software, Inc.
* Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
- * Copyright 2007 Johannes Berg <johannes@sipsolutions.net>
+ * Copyright 2007-2008 Johannes Berg <johannes@sipsolutions.net>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* tasklet function.
*
* NOTE: If the driver opts to use the _irqsafe() functions, it may not also
- * use the non-irqsafe functions!
+ * use the non-IRQ-safe functions!
*/
/**
*/
/**
- * enum ieee80211_notification_type - Low level driver notification
- * @IEEE80211_NOTIFY_RE_ASSOC: start the re-association sequence
- */
-enum ieee80211_notification_types {
- IEEE80211_NOTIFY_RE_ASSOC,
-};
-
-/**
* struct ieee80211_ht_bss_info - describing BSS's HT characteristics
*
* This structure describes most essential parameters needed
- * to describe 802.11n HT characteristics in a BSS
+ * to describe 802.11n HT characteristics in a BSS.
*
* @primary_channel: channel number of primery channel
* @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
* The information provided in this structure is required for QoS
* transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
*
- * @aifs: arbitration interface space [0..255, -1: use default]
- * @cw_min: minimum contention window [will be a value of the form
- * 2^n-1 in the range 1..1023; 0: use default]
+ * @aifs: arbitration interframe space [0..255]
+ * @cw_min: minimum contention window [a value of the form
+ * 2^n-1 in the range 1..32767]
* @cw_max: maximum contention window [like @cw_min]
* @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
*/
struct ieee80211_tx_queue_params {
- s16 aifs;
+ u16 txop;
u16 cw_min;
u16 cw_max;
- u16 txop;
+ u8 aifs;
};
/**
* also implies a change in the AID.
* @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
* @BSS_CHANGED_ERP_PREAMBLE: preamble changed
+ * @BSS_CHANGED_ERP_SLOT: slot timing changed
* @BSS_CHANGED_HT: 802.11n parameters changed
+ * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
*/
enum ieee80211_bss_change {
BSS_CHANGED_ASSOC = 1<<0,
BSS_CHANGED_ERP_CTS_PROT = 1<<1,
BSS_CHANGED_ERP_PREAMBLE = 1<<2,
+ BSS_CHANGED_ERP_SLOT = 1<<3,
BSS_CHANGED_HT = 1<<4,
+ BSS_CHANGED_BASIC_RATES = 1<<5,
+};
+
+/**
+ * struct ieee80211_bss_ht_conf - BSS's changing HT configuration
+ * @operation_mode: HT operation mode (like in &struct ieee80211_ht_info)
+ */
+struct ieee80211_bss_ht_conf {
+ u16 operation_mode;
};
/**
* @assoc: association status
* @aid: association ID number, valid only when @assoc is true
* @use_cts_prot: use CTS protection
- * @use_short_preamble: use 802.11b short preamble
+ * @use_short_preamble: use 802.11b short preamble;
+ * if the hardware cannot handle this it must set the
+ * IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
+ * @use_short_slot: use short slot time (only relevant for ERP);
+ * if the hardware cannot handle this it must set the
+ * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
+ * @dtim_period: num of beacons before the next DTIM, for PSM
* @timestamp: beacon timestamp
* @beacon_int: beacon interval
- * @assoc_capability: capabbilities taken from assoc resp
- * @assoc_ht: association in HT mode
- * @ht_conf: ht capabilities
- * @ht_bss_conf: ht extended capabilities
+ * @assoc_capability: capabilities taken from assoc resp
+ * @ht: BSS's HT configuration
+ * @basic_rates: bitmap of basic rates, each bit stands for an
+ * index into the rate table configured by the driver in
+ * the current band.
*/
struct ieee80211_bss_conf {
/* association related data */
/* erp related data */
bool use_cts_prot;
bool use_short_preamble;
+ bool use_short_slot;
+ u8 dtim_period;
u16 beacon_int;
u16 assoc_capability;
u64 timestamp;
- /* ht related data */
- bool assoc_ht;
- struct ieee80211_ht_info *ht_conf;
- struct ieee80211_ht_bss_info *ht_bss_conf;
+ u32 basic_rates;
+ struct ieee80211_bss_ht_conf ht;
};
/**
- * enum mac80211_tx_flags - flags to transmission information/status
+ * enum mac80211_tx_control_flags - flags to describe transmission information/status
*
- * These flags are used with the @flags member of &ieee80211_tx_info
+ * These flags are used with the @flags member of &ieee80211_tx_info.
*
* @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame.
- * @IEEE80211_TX_CTL_DO_NOT_ENCRYPT: send this frame without encryption;
- * e.g., for EAPOL frame
- * @IEEE80211_TX_CTL_USE_RTS_CTS: use RTS-CTS before sending frame
- * @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g.,
- * for combined 802.11g / 802.11b networks)
+ * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
+ * number to this frame, taking care of not overwriting the fragment
+ * number and increasing the sequence number only when the
+ * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
+ * assign sequence numbers to QoS-data frames but cannot do so correctly
+ * for non-QoS-data and management frames because beacons need them from
+ * that counter as well and mac80211 cannot guarantee proper sequencing.
+ * If this flag is set, the driver should instruct the hardware to
+ * assign a sequence number to the frame or assign one itself. Cf. IEEE
+ * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
+ * beacons and always be clear for frames without a sequence number field.
* @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
- * @IEEE80211_TX_CTL_RATE_CTRL_PROBE
* @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
* station
- * @IEEE80211_TX_CTL_REQUEUE:
* @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
- * @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the
- * through set_retry_limit configured long retry value
- * @IEEE80211_TX_CTL_EAPOL_FRAME: internal to mac80211
* @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
* @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
- * @IEEE80211_TX_CTL_OFDM_HT: this frame can be sent in HT OFDM rates. number
- * of streams when this flag is on can be extracted from antenna_sel_tx,
- * so if 1 antenna is marked use SISO, 2 antennas marked use MIMO, n
- * antennas marked use MIMO_n.
- * @IEEE80211_TX_CTL_GREEN_FIELD: use green field protection for this frame
- * @IEEE80211_TX_CTL_40_MHZ_WIDTH: send this frame using 40 Mhz channel width
- * @IEEE80211_TX_CTL_DUP_DATA: duplicate data frame on both 20 Mhz channels
- * @IEEE80211_TX_CTL_SHORT_GI: send this frame using short guard interval
+ * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
* @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
* because the destination STA was in powersave mode.
* @IEEE80211_TX_STAT_ACK: Frame was acknowledged
* @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
* is for the whole aggregation.
+ * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
+ * so consider using block ack request (BAR).
+ * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
+ * set by rate control algorithms to indicate probe rate, will
+ * be cleared for fragmented frames (except on the last fragment)
*/
enum mac80211_tx_control_flags {
IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
- IEEE80211_TX_CTL_DO_NOT_ENCRYPT = BIT(1),
- IEEE80211_TX_CTL_USE_RTS_CTS = BIT(2),
- IEEE80211_TX_CTL_USE_CTS_PROTECT = BIT(3),
- IEEE80211_TX_CTL_NO_ACK = BIT(4),
- IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(5),
- IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(6),
- IEEE80211_TX_CTL_REQUEUE = BIT(7),
- IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(8),
- IEEE80211_TX_CTL_SHORT_PREAMBLE = BIT(9),
- IEEE80211_TX_CTL_LONG_RETRY_LIMIT = BIT(10),
- IEEE80211_TX_CTL_EAPOL_FRAME = BIT(11),
- IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(12),
- IEEE80211_TX_CTL_AMPDU = BIT(13),
- IEEE80211_TX_CTL_OFDM_HT = BIT(14),
- IEEE80211_TX_CTL_GREEN_FIELD = BIT(15),
- IEEE80211_TX_CTL_40_MHZ_WIDTH = BIT(16),
- IEEE80211_TX_CTL_DUP_DATA = BIT(17),
- IEEE80211_TX_CTL_SHORT_GI = BIT(18),
- IEEE80211_TX_CTL_INJECTED = BIT(19),
- IEEE80211_TX_STAT_TX_FILTERED = BIT(20),
- IEEE80211_TX_STAT_ACK = BIT(21),
- IEEE80211_TX_STAT_AMPDU = BIT(22),
+ IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
+ IEEE80211_TX_CTL_NO_ACK = BIT(2),
+ IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
+ IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
+ IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
+ IEEE80211_TX_CTL_AMPDU = BIT(6),
+ IEEE80211_TX_CTL_INJECTED = BIT(7),
+ IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
+ IEEE80211_TX_STAT_ACK = BIT(9),
+ IEEE80211_TX_STAT_AMPDU = BIT(10),
+ IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
+ IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
};
+/**
+ * enum mac80211_rate_control_flags - per-rate flags set by the
+ * Rate Control algorithm.
+ *
+ * These flags are set by the Rate control algorithm for each rate during tx,
+ * in the @flags member of struct ieee80211_tx_rate.
+ *
+ * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
+ * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
+ * This is set if the current BSS requires ERP protection.
+ * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
+ * @IEEE80211_TX_RC_MCS: HT rate.
+ * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
+ * Greenfield mode.
+ * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
+ * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
+ * adjacent 20 MHz channels, if the current channel type is
+ * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
+ * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
+ */
+enum mac80211_rate_control_flags {
+ IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
+ IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
+ IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
+
+ /* rate index is an MCS rate number instead of an index */
+ IEEE80211_TX_RC_MCS = BIT(3),
+ IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
+ IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
+ IEEE80211_TX_RC_DUP_DATA = BIT(6),
+ IEEE80211_TX_RC_SHORT_GI = BIT(7),
+};
+
+
+/* there are 40 bytes if you don't need the rateset to be kept */
+#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
+
+/* if you do need the rateset, then you have less space */
+#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
-#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE \
- (sizeof(((struct sk_buff *)0)->cb) - 8)
-#define IEEE80211_TX_INFO_DRIVER_DATA_PTRS \
- (IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *))
+/* maximum number of rate stages */
+#define IEEE80211_TX_MAX_RATES 5
+
+/**
+ * struct ieee80211_tx_rate - rate selection/status
+ *
+ * @idx: rate index to attempt to send with
+ * @flags: rate control flags (&enum mac80211_rate_control_flags)
+ * @count: number of tries in this rate before going to the next rate
+ *
+ * A value of -1 for @idx indicates an invalid rate and, if used
+ * in an array of retry rates, that no more rates should be tried.
+ *
+ * When used for transmit status reporting, the driver should
+ * always report the rate along with the flags it used.
+ */
+struct ieee80211_tx_rate {
+ s8 idx;
+ u8 count;
+ u8 flags;
+} __attribute__((packed));
/**
* struct ieee80211_tx_info - skb transmit information
* (2) driver internal use (if applicable)
* (3) TX status information - driver tells mac80211 what happened
*
+ * The TX control's sta pointer is only valid during the ->tx call,
+ * it may be NULL.
+ *
* @flags: transmit info flags, defined above
- * @retry_count: number of retries
- * @excessive_retries: set to 1 if the frame was retried many times
- * but not acknowledged
+ * @band: the band to transmit on (use for checking for races)
+ * @antenna_sel_tx: antenna to use, 0 for automatic diversity
+ * @pad: padding, ignore
+ * @control: union for control data
+ * @status: union for status data
+ * @driver_data: array of driver_data pointers
* @ampdu_ack_len: number of aggregated frames.
* relevant only if IEEE80211_TX_STATUS_AMPDU was set.
* @ampdu_ack_map: block ack bit map for the aggregation.
/* common information */
u32 flags;
u8 band;
- s8 tx_rate_idx;
+
u8 antenna_sel_tx;
- /* 1 byte hole */
+ /* 2 byte hole */
+ u8 pad[2];
union {
struct {
+ union {
+ /* rate control */
+ struct {
+ struct ieee80211_tx_rate rates[
+ IEEE80211_TX_MAX_RATES];
+ s8 rts_cts_rate_idx;
+ };
+ /* only needed before rate control */
+ unsigned long jiffies;
+ };
+ /* NB: vif can be NULL for injected frames */
struct ieee80211_vif *vif;
struct ieee80211_key_conf *hw_key;
- unsigned long jiffies;
- int ifindex;
- u16 aid;
- s8 rts_cts_rate_idx, alt_retry_rate_idx;
- u8 retry_limit;
- u8 icv_len;
- u8 iv_len;
+ struct ieee80211_sta *sta;
} control;
struct {
+ struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
+ u8 ampdu_ack_len;
u64 ampdu_ack_map;
int ack_signal;
- u8 retry_count;
- bool excessive_retries;
- u8 ampdu_ack_len;
+ /* 8 bytes free */
} status;
- void *driver_data[IEEE80211_TX_INFO_DRIVER_DATA_PTRS];
+ struct {
+ struct ieee80211_tx_rate driver_rates[
+ IEEE80211_TX_MAX_RATES];
+ void *rate_driver_data[
+ IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
+ };
+ void *driver_data[
+ IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
};
};
return (struct ieee80211_tx_info *)skb->cb;
}
+/**
+ * ieee80211_tx_info_clear_status - clear TX status
+ *
+ * @info: The &struct ieee80211_tx_info to be cleared.
+ *
+ * When the driver passes an skb back to mac80211, it must report
+ * a number of things in TX status. This function clears everything
+ * in the TX status but the rate control information (it does clear
+ * the count since you need to fill that in anyway).
+ *
+ * NOTE: You can only use this function if you do NOT use
+ * info->driver_data! Use info->rate_driver_data
+ * instead if you need only the less space that allows.
+ */
+static inline void
+ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
+{
+ int i;
+
+ BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
+ offsetof(struct ieee80211_tx_info, control.rates));
+ BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
+ offsetof(struct ieee80211_tx_info, driver_rates));
+ BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
+ /* clear the rate counts */
+ for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
+ info->status.rates[i].count = 0;
+
+ BUILD_BUG_ON(
+ offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
+ memset(&info->status.ampdu_ack_len, 0,
+ sizeof(struct ieee80211_tx_info) -
+ offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
+}
+
/**
* enum mac80211_rx_flags - receive flags
* @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
* is valid. This is useful in monitor mode and necessary for beacon frames
* to enable IBSS merging.
+ * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
+ * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
+ * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
+ * @RX_FLAG_SHORT_GI: Short guard interval was used
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = 1<<0,
RX_FLAG_FAILED_FCS_CRC = 1<<5,
RX_FLAG_FAILED_PLCP_CRC = 1<<6,
RX_FLAG_TSFT = 1<<7,
+ RX_FLAG_SHORTPRE = 1<<8,
+ RX_FLAG_HT = 1<<9,
+ RX_FLAG_40MHZ = 1<<10,
+ RX_FLAG_SHORT_GI = 1<<11,
};
/**
* @noise: noise when receiving this frame, in dBm.
* @qual: overall signal quality indication, in percent (0-100).
* @antenna: antenna used
- * @rate_idx: index of data rate into band's supported rates
+ * @rate_idx: index of data rate into band's supported rates or MCS index if
+ * HT rates are use (RX_FLAG_HT)
* @flag: %RX_FLAG_*
*/
struct ieee80211_rx_status {
*
* Flags to define PHY configuration options
*
- * @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time
* @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
- * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported)
+ * @IEEE80211_CONF_PS: Enable 802.11 power save mode
*/
enum ieee80211_conf_flags {
- IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0),
- IEEE80211_CONF_RADIOTAP = (1<<1),
- IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2),
+ IEEE80211_CONF_RADIOTAP = (1<<0),
+ IEEE80211_CONF_PS = (1<<1),
+};
+
+/* XXX: remove all this once drivers stop trying to use it */
+static inline int __deprecated __IEEE80211_CONF_SHORT_SLOT_TIME(void)
+{
+ return 0;
+}
+#define IEEE80211_CONF_SHORT_SLOT_TIME (__IEEE80211_CONF_SHORT_SLOT_TIME())
+
+/**
+ * enum ieee80211_conf_changed - denotes which configuration changed
+ *
+ * @IEEE80211_CONF_CHANGE_RADIO_ENABLED: the value of radio_enabled changed
+ * @IEEE80211_CONF_CHANGE_BEACON_INTERVAL: the beacon interval changed
+ * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
+ * @IEEE80211_CONF_CHANGE_RADIOTAP: the radiotap flag changed
+ * @IEEE80211_CONF_CHANGE_PS: the PS flag changed
+ * @IEEE80211_CONF_CHANGE_DYNPS_TIMEOUT: the dynamic PS timeout changed
+ * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
+ * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
+ * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
+ */
+enum ieee80211_conf_changed {
+ IEEE80211_CONF_CHANGE_RADIO_ENABLED = BIT(0),
+ IEEE80211_CONF_CHANGE_BEACON_INTERVAL = BIT(1),
+ IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
+ IEEE80211_CONF_CHANGE_RADIOTAP = BIT(3),
+ IEEE80211_CONF_CHANGE_PS = BIT(4),
+ IEEE80211_CONF_CHANGE_DYNPS_TIMEOUT = BIT(5),
+ IEEE80211_CONF_CHANGE_POWER = BIT(6),
+ IEEE80211_CONF_CHANGE_CHANNEL = BIT(7),
+ IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(8),
};
/**
* This struct indicates how the driver shall configure the hardware.
*
* @radio_enabled: when zero, driver is required to switch off the radio.
- * TODO make a flag
* @beacon_int: beacon interval (TODO make interface config)
+ * @listen_interval: listen interval in units of beacon interval
* @flags: configuration flags defined above
* @power_level: requested transmit power (in dBm)
- * @max_antenna_gain: maximum antenna gain (in dBi)
- * @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
- * 1/2: antenna 0/1
- * @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
- * @ht_conf: describes current self configuration of 802.11n HT capabilies
- * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
+ * @dynamic_ps_timeout: dynamic powersave timeout (in ms)
* @channel: the channel to tune to
+ * @channel_type: the channel (HT) type
+ * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
+ * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ * but actually means the number of transmissions not the number of retries
+ * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
+ * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ * number of transmissions not the number of retries
*/
struct ieee80211_conf {
- int radio_enabled;
-
int beacon_int;
u32 flags;
- int power_level;
- int max_antenna_gain;
- u8 antenna_sel_tx;
- u8 antenna_sel_rx;
+ int power_level, dynamic_ps_timeout;
- struct ieee80211_channel *channel;
+ u16 listen_interval;
+ bool radio_enabled;
- struct ieee80211_ht_info ht_conf;
- struct ieee80211_ht_bss_info ht_bss_conf;
-};
+ u8 long_frame_max_tx_count, short_frame_max_tx_count;
-/**
- * enum ieee80211_if_types - types of 802.11 network interfaces
- *
- * @IEEE80211_IF_TYPE_INVALID: invalid interface type, not used
- * by mac80211 itself
- * @IEEE80211_IF_TYPE_AP: interface in AP mode.
- * @IEEE80211_IF_TYPE_MGMT: special interface for communication with hostap
- * daemon. Drivers should never see this type.
- * @IEEE80211_IF_TYPE_STA: interface in STA (client) mode.
- * @IEEE80211_IF_TYPE_IBSS: interface in IBSS (ad-hoc) mode.
- * @IEEE80211_IF_TYPE_MNTR: interface in monitor (rfmon) mode.
- * @IEEE80211_IF_TYPE_WDS: interface in WDS mode.
- * @IEEE80211_IF_TYPE_VLAN: VLAN interface bound to an AP, drivers
- * will never see this type.
- * @IEEE80211_IF_TYPE_MESH_POINT: 802.11s mesh point
- */
-enum ieee80211_if_types {
- IEEE80211_IF_TYPE_INVALID,
- IEEE80211_IF_TYPE_AP,
- IEEE80211_IF_TYPE_STA,
- IEEE80211_IF_TYPE_IBSS,
- IEEE80211_IF_TYPE_MESH_POINT,
- IEEE80211_IF_TYPE_MNTR,
- IEEE80211_IF_TYPE_WDS,
- IEEE80211_IF_TYPE_VLAN,
+ struct ieee80211_channel *channel;
+ enum nl80211_channel_type channel_type;
};
/**
* use during the life of a virtual interface.
*
* @type: type of this virtual interface
+ * @bss_conf: BSS configuration for this interface, either our own
+ * or the BSS we're associated to
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *).
*/
struct ieee80211_vif {
- enum ieee80211_if_types type;
+ enum nl80211_iftype type;
+ struct ieee80211_bss_conf bss_conf;
/* must be last */
u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
- return vif->type == IEEE80211_IF_TYPE_MESH_POINT;
+ return vif->type == NL80211_IFTYPE_MESH_POINT;
#endif
return false;
}
* @vif: pointer to a driver-use per-interface structure. The pointer
* itself is also used for various functions including
* ieee80211_beacon_get() and ieee80211_get_buffered_bc().
- * @type: one of &enum ieee80211_if_types constants. Determines the type of
+ * @type: one of &enum nl80211_iftype constants. Determines the type of
* added/removed interface.
* @mac_addr: pointer to MAC address of the interface. This pointer is valid
* until the interface is removed (i.e. it cannot be used after
* in pure monitor mode.
*/
struct ieee80211_if_init_conf {
- enum ieee80211_if_types type;
+ enum nl80211_iftype type;
struct ieee80211_vif *vif;
void *mac_addr;
};
/**
+ * enum ieee80211_if_conf_change - interface config change flags
+ *
+ * @IEEE80211_IFCC_BSSID: The BSSID changed.
+ * @IEEE80211_IFCC_BEACON: The beacon for this interface changed
+ * (currently AP and MESH only), use ieee80211_beacon_get().
+ * @IEEE80211_IFCC_BEACON_ENABLED: The enable_beacon value changed.
+ */
+enum ieee80211_if_conf_change {
+ IEEE80211_IFCC_BSSID = BIT(0),
+ IEEE80211_IFCC_BEACON = BIT(1),
+ IEEE80211_IFCC_BEACON_ENABLED = BIT(2),
+};
+
+/**
* struct ieee80211_if_conf - configuration of an interface
*
- * @type: type of the interface. This is always the same as was specified in
- * &struct ieee80211_if_init_conf. The type of an interface never changes
- * during the life of the interface; this field is present only for
- * convenience.
+ * @changed: parameters that have changed, see &enum ieee80211_if_conf_change.
* @bssid: BSSID of the network we are associated to/creating.
- * @ssid: used (together with @ssid_len) by drivers for hardware that
- * generate beacons independently. The pointer is valid only during the
- * config_interface() call, so copy the value somewhere if you need
- * it.
- * @ssid_len: length of the @ssid field.
- * @beacon: beacon template. Valid only if @host_gen_beacon_template in
- * &struct ieee80211_hw is set. The driver is responsible of freeing
- * the sk_buff.
- * @beacon_control: tx_control for the beacon template, this field is only
- * valid when the @beacon field was set.
+ * @enable_beacon: Indicates whether beacons can be sent.
+ * This is valid only for AP/IBSS/MESH modes.
*
* This structure is passed to the config_interface() callback of
* &struct ieee80211_hw.
*/
struct ieee80211_if_conf {
- int type;
- u8 *bssid;
- u8 *ssid;
- size_t ssid_len;
- struct sk_buff *beacon;
+ u32 changed;
+ const u8 *bssid;
+ bool enable_beacon;
};
/**
* @ALG_WEP: WEP40 or WEP104
* @ALG_TKIP: TKIP
* @ALG_CCMP: CCMP (AES)
+ * @ALG_AES_CMAC: AES-128-CMAC
*/
enum ieee80211_key_alg {
ALG_WEP,
ALG_TKIP,
ALG_CCMP,
+ ALG_AES_CMAC,
};
+/**
+ * enum ieee80211_key_len - key length
+ * @LEN_WEP40: WEP 5-byte long key
+ * @LEN_WEP104: WEP 13-byte long key
+ */
+enum ieee80211_key_len {
+ LEN_WEP40 = 5,
+ LEN_WEP104 = 13,
+};
/**
* enum ieee80211_key_flags - key flags
* generation in software.
* @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
* that the key is pairwise rather then a shared key.
+ * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
+ * CCMP key if it requires CCMP encryption of management frames (MFP) to
+ * be done in software.
*/
enum ieee80211_key_flags {
IEEE80211_KEY_FLAG_WMM_STA = 1<<0,
IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1,
IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
+ IEEE80211_KEY_FLAG_SW_MGMT = 1<<4,
};
/**
* - Temporal Encryption Key (128 bits)
* - Temporal Authenticator Tx MIC Key (64 bits)
* - Temporal Authenticator Rx MIC Key (64 bits)
- *
+ * @icv_len: The ICV length for this key type
+ * @iv_len: The IV length for this key type
*/
struct ieee80211_key_conf {
enum ieee80211_key_alg alg;
+ u8 icv_len;
+ u8 iv_len;
u8 hw_key_idx;
u8 flags;
s8 keyidx;
};
/**
+ * struct ieee80211_sta - station table entry
+ *
+ * A station table entry represents a station we are possibly
+ * communicating with. Since stations are RCU-managed in
+ * mac80211, any ieee80211_sta pointer you get access to must
+ * either be protected by rcu_read_lock() explicitly or implicitly,
+ * or you must take good care to not use such a pointer after a
+ * call to your sta_notify callback that removed it.
+ *
+ * @addr: MAC address
+ * @aid: AID we assigned to the station if we're an AP
+ * @supp_rates: Bitmap of supported rates (per band)
+ * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
+ * @drv_priv: data area for driver use, will always be aligned to
+ * sizeof(void *), size is determined in hw information.
+ */
+struct ieee80211_sta {
+ u32 supp_rates[IEEE80211_NUM_BANDS];
+ u8 addr[ETH_ALEN];
+ u16 aid;
+ struct ieee80211_sta_ht_cap ht_cap;
+
+ /* must be last */
+ u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+/**
* enum sta_notify_cmd - sta notify command
*
* Used with the sta_notify() callback in &struct ieee80211_ops, this
- * indicates addition and removal of a station to station table
+ * indicates addition and removal of a station to station table,
+ * or if a associated station made a power state transition.
*
* @STA_NOTIFY_ADD: a station was added to the station table
* @STA_NOTIFY_REMOVE: a station being removed from the station table
+ * @STA_NOTIFY_SLEEP: a station is now sleeping
+ * @STA_NOTIFY_AWAKE: a sleeping station woke up
*/
enum sta_notify_cmd {
- STA_NOTIFY_ADD, STA_NOTIFY_REMOVE
+ STA_NOTIFY_ADD, STA_NOTIFY_REMOVE,
+ STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
};
/**
* any particular flags. There are some exceptions to this rule,
* however, so you are advised to review these flags carefully.
*
- * @IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE:
- * The device only needs to be supplied with a beacon template.
- * If you need the host to generate each beacon then don't use
- * this flag and call ieee80211_beacon_get() when you need the
- * next beacon frame. Note that if you set this flag, you must
- * implement the set_tim() callback for powersave mode to work
- * properly.
- * This flag is only relevant for access-point mode.
- *
* @IEEE80211_HW_RX_INCLUDES_FCS:
* Indicates that received frames passed to the stack include
* the FCS at the end.
* rely on the host system for such buffering. This option is used
* to configure the IEEE 802.11 upper layer to buffer broadcast and
* multicast frames when there are power saving stations so that
- * the driver can fetch them with ieee80211_get_buffered_bc(). Note
- * that not setting this flag works properly only when the
- * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because
- * otherwise the stack will not know when the DTIM beacon was sent.
+ * the driver can fetch them with ieee80211_get_buffered_bc().
*
* @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
* Hardware is not capable of short slot operation on the 2.4 GHz band.
* expect values between 0 and @max_signal.
* If possible please provide dB or dBm instead.
*
- * @IEEE80211_HW_SIGNAL_DB:
- * Hardware gives signal values in dB, decibel difference from an
- * arbitrary, fixed reference. We expect values between 0 and @max_signal.
- * If possible please provide dBm instead.
- *
* @IEEE80211_HW_SIGNAL_DBM:
* Hardware gives signal values in dBm, decibel difference from
* one milliwatt. This is the preferred method since it is standardized
* @IEEE80211_HW_NOISE_DBM:
* Hardware can provide noise (radio interference) values in units dBm,
* decibel difference from one milliwatt.
+ *
+ * @IEEE80211_HW_SPECTRUM_MGMT:
+ * Hardware supports spectrum management defined in 802.11h
+ * Measurement, Channel Switch, Quieting, TPC
+ *
+ * @IEEE80211_HW_AMPDU_AGGREGATION:
+ * Hardware supports 11n A-MPDU aggregation.
+ *
+ * @IEEE80211_HW_SUPPORTS_PS:
+ * Hardware has power save support (i.e. can go to sleep).
+ *
+ * @IEEE80211_HW_PS_NULLFUNC_STACK:
+ * Hardware requires nullfunc frame handling in stack, implies
+ * stack support for dynamic PS.
+ *
+ * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
+ * Hardware has support for dynamic PS.
+ *
+ * @IEEE80211_HW_MFP_CAPABLE:
+ * Hardware supports management frame protection (MFP, IEEE 802.11w).
*/
enum ieee80211_hw_flags {
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0,
IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
- IEEE80211_HW_SIGNAL_DB = 1<<6,
- IEEE80211_HW_SIGNAL_DBM = 1<<7,
- IEEE80211_HW_NOISE_DBM = 1<<8,
+ IEEE80211_HW_SIGNAL_DBM = 1<<6,
+ IEEE80211_HW_NOISE_DBM = 1<<7,
+ IEEE80211_HW_SPECTRUM_MGMT = 1<<8,
+ IEEE80211_HW_AMPDU_AGGREGATION = 1<<9,
+ IEEE80211_HW_SUPPORTS_PS = 1<<10,
+ IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11,
+ IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12,
+ IEEE80211_HW_MFP_CAPABLE = 1<<13,
};
/**
* @conf: &struct ieee80211_conf, device configuration, don't use.
*
* @workqueue: single threaded workqueue available for driver use,
- * allocated by mac80211 on registration and flushed on
- * unregistration.
+ * allocated by mac80211 on registration and flushed when an
+ * interface is removed.
+ * NOTICE: All work performed on this workqueue must not
+ * acquire the RTNL lock.
*
* @priv: pointer to private area that was allocated for driver use
* along with this structure.
* @max_signal: Maximum value for signal (rssi) in RX information, used
* only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
+ * @max_listen_interval: max listen interval in units of beacon interval
+ * that HW supports
+ *
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
* queues need to have configurable access parameters.
*
* @vif_data_size: size (in bytes) of the drv_priv data area
* within &struct ieee80211_vif.
+ * @sta_data_size: size (in bytes) of the drv_priv data area
+ * within &struct ieee80211_sta.
+ *
+ * @max_rates: maximum number of alternate rate retry stages
+ * @max_rate_tries: maximum number of tries for each stage
*/
struct ieee80211_hw {
struct ieee80211_conf conf;
unsigned int extra_tx_headroom;
int channel_change_time;
int vif_data_size;
- u16 queues, ampdu_queues;
+ int sta_data_size;
+ u16 queues;
+ u16 ampdu_queues;
+ u16 max_listen_interval;
s8 max_signal;
+ u8 max_rates;
+ u8 max_rate_tries;
};
/**
+ * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
+ *
+ * @wiphy: the &struct wiphy which we want to query
+ *
+ * mac80211 drivers can use this to get to their respective
+ * &struct ieee80211_hw. Drivers wishing to get to their own private
+ * structure can then access it via hw->priv. Note that mac802111 drivers should
+ * not use wiphy_priv() to try to get their private driver structure as this
+ * is already used internally by mac80211.
+ */
+struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
+
+/**
* SET_IEEE80211_DEV - set device for 802.11 hardware
*
* @hw: the &struct ieee80211_hw to set the device for
}
/**
- * SET_IEEE80211_PERM_ADDR - set the permanenet MAC address for 802.11 hardware
+ * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
*
* @hw: the &struct ieee80211_hw to set the MAC address for
* @addr: the address to set
static inline int ieee80211_num_regular_queues(struct ieee80211_hw *hw)
{
-#ifdef CONFIG_MAC80211_QOS
return hw->queues;
-#else
- return 1;
-#endif
}
static inline int ieee80211_num_queues(struct ieee80211_hw *hw)
{
-#ifdef CONFIG_MAC80211_QOS
return hw->queues + hw->ampdu_queues;
-#else
- return 1;
-#endif
}
static inline struct ieee80211_rate *
ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
const struct ieee80211_tx_info *c)
{
- if (WARN_ON(c->tx_rate_idx < 0))
+ if (WARN_ON(c->control.rates[0].idx < 0))
return NULL;
- return &hw->wiphy->bands[c->band]->bitrates[c->tx_rate_idx];
+ return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
}
static inline struct ieee80211_rate *
static inline struct ieee80211_rate *
ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
- const struct ieee80211_tx_info *c)
+ const struct ieee80211_tx_info *c, int idx)
{
- if (c->control.alt_retry_rate_idx < 0)
+ if (c->control.rates[idx + 1].idx < 0)
return NULL;
- return &hw->wiphy->bands[c->band]->bitrates[c->control.alt_retry_rate_idx];
+ return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
}
/**
*
* The set_key() callback in the &struct ieee80211_ops for a given
* device is called to enable hardware acceleration of encryption and
- * decryption. The callback takes an @address parameter that will be
- * the broadcast address for default keys, the other station's hardware
- * address for individual keys or the zero address for keys that will
- * be used only for transmission.
+ * decryption. The callback takes a @sta parameter that will be NULL
+ * for default keys or keys used for transmission only, or point to
+ * the station information for the peer for individual keys.
* Multiple transmission keys with the same key index may be used when
* VLANs are configured for an access point.
*
- * The @local_address parameter will always be set to our own address,
- * this is only relevant if you support multiple local addresses.
- *
* When transmitting, the TX control data will use the @hw_key_idx
* selected by the driver by modifying the &struct ieee80211_key_conf
* pointed to by the @key parameter to the set_key() function.
* This happens everytime the iv16 wraps around (every 65536 packets). The
* set_key() call will happen only once for each key (unless the AP did
* rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
- * provided by udpate_tkip_key only. The trigger that makes mac80211 call this
+ * provided by update_tkip_key only. The trigger that makes mac80211 call this
* handler is software decryption with wrap around of iv16.
*/
/**
+ * DOC: Powersave support
+ *
+ * mac80211 has support for various powersave implementations.
+ *
+ * First, it can support hardware that handles all powersaving by
+ * itself, such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS
+ * hardware flag. In that case, it will be told about the desired
+ * powersave mode depending on the association status, and the driver
+ * must take care of sending nullfunc frames when necessary, i.e. when
+ * entering and leaving powersave mode. The driver is required to look at
+ * the AID in beacons and signal to the AP that it woke up when it finds
+ * traffic directed to it. This mode supports dynamic PS by simply
+ * enabling/disabling PS.
+ *
+ * Additionally, such hardware may set the %IEEE80211_HW_SUPPORTS_DYNAMIC_PS
+ * flag to indicate that it can support dynamic PS mode itself (see below).
+ *
+ * Other hardware designs cannot send nullfunc frames by themselves and also
+ * need software support for parsing the TIM bitmap. This is also supported
+ * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
+ * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
+ * required to pass up beacons. Additionally, in this case, mac80211 will
+ * wake up the hardware when multicast traffic is announced in the beacon.
+ *
+ * FIXME: I don't think we can be fast enough in software when we want to
+ * receive multicast traffic?
+ *
+ * Dynamic powersave mode is an extension to normal powersave mode in which
+ * the hardware stays awake for a user-specified period of time after sending
+ * a frame so that reply frames need not be buffered and therefore delayed
+ * to the next wakeup. This can either be supported by hardware, in which case
+ * the driver needs to look at the @dynamic_ps_timeout hardware configuration
+ * value, or by the stack if all nullfunc handling is in the stack.
+ */
+
+/**
* DOC: Frame filtering
*
* mac80211 requires to see many management frames for proper
* @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
* @IEEE80211_AMPDU_TX_START: start Tx aggregation
* @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
+ * @IEEE80211_AMPDU_TX_RESUME: resume TX aggregation
*/
enum ieee80211_ampdu_mlme_action {
IEEE80211_AMPDU_RX_START,
IEEE80211_AMPDU_RX_STOP,
IEEE80211_AMPDU_TX_START,
IEEE80211_AMPDU_TX_STOP,
+ IEEE80211_AMPDU_TX_RESUME,
};
/**
* configuration in the TX control data. This handler should,
* preferably, never fail and stop queues appropriately, more
* importantly, however, it must never fail for A-MPDU-queues.
+ * This function should return NETDEV_TX_OK except in very
+ * limited cases.
* Must be implemented and atomic.
*
* @start: Called before the first netdevice attached to the hardware
* Must be implemented.
*
* @add_interface: Called when a netdevice attached to the hardware is
- * enabled. Because it is not called for monitor mode devices, @open
+ * enabled. Because it is not called for monitor mode devices, @start
* and @stop must be implemented.
* The driver should perform any initialization it needs before
* the device can be enabled. The initial configuration for the
*
* @config: Handler for configuration requests. IEEE 802.11 code calls this
* function to change hardware configuration, e.g., channel.
+ * This function should never fail but returns a negative error code
+ * if it does.
*
* @config_interface: Handler for configuration requests related to interfaces
* (e.g. BSSID changes.)
+ * Returns a negative error code which will be seen in userspace.
*
* @bss_info_changed: Handler for configuration requests related to BSS
* parameters that may vary during BSS's lifespan, and may affect low
* See the section "Frame filtering" for more information.
* This callback must be implemented and atomic.
*
- * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon
- * generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set)
- * mac80211 calls this function when a TIM bit must be set or cleared
- * for a given AID. Must be atomic.
+ * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
+ * must be set or cleared for a given STA. Must be atomic.
*
* @set_key: See the section "Hardware crypto acceleration"
* This callback can sleep, and is only called between add_interface
- * and remove_interface calls, i.e. while the interface with the
- * given local_address is enabled.
+ * and remove_interface calls, i.e. while the given virtual interface
+ * is enabled.
+ * Returns a negative error code if the key can't be added.
*
* @update_tkip_key: See the section "Hardware crypto acceleration"
* This callback will be called in the context of Rx. Called for drivers
* @hw_scan: Ask the hardware to service the scan request, no need to start
* the scan state machine in stack. The scan must honour the channel
* configuration done by the regulatory agent in the wiphy's registered
- * bands.
+ * bands. When the scan finishes, ieee80211_scan_completed() must be
+ * called; note that it also must be called when the scan cannot finish
+ * because the hardware is turned off! Anything else is a bug!
+ * Returns a negative error code which will be seen in userspace.
*
- * @get_stats: return low-level statistics
+ * @get_stats: Return low-level statistics.
+ * Returns zero if statistics are available.
*
* @get_tkip_seq: If your device implements TKIP encryption in hardware this
* callback should be provided to read the TKIP transmit IVs (both IV32
*
* @set_rts_threshold: Configuration of RTS threshold (if device needs it)
*
- * @set_frag_threshold: Configuration of fragmentation threshold. Assign this if
- * the device does fragmentation by itself; if this method is assigned then
- * the stack will not do fragmentation.
- *
- * @set_retry_limit: Configuration of retry limits (if device needs it)
- *
- * @sta_notify: Notifies low level driver about addition or removal
- * of assocaited station or AP.
+ * @sta_notify: Notifies low level driver about addition, removal or power
+ * state transition of an associated station, AP, IBSS/WDS/mesh peer etc.
+ * Must be atomic.
*
* @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
- * bursting) for a hardware TX queue. Must be atomic.
+ * bursting) for a hardware TX queue.
+ * Returns a negative error code on failure.
*
* @get_tx_stats: Get statistics of the current TX queue status. This is used
* to get number of currently queued packets (queue length), maximum queue
* hw->ampdu_queues items.
*
* @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
- * this is only used for IBSS mode debugging and, as such, is not a
- * required function. Must be atomic.
+ * this is only used for IBSS mode BSSID merging and debugging. Is not a
+ * required function.
+ *
+ * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
+ * Currently, this is only used for IBSS mode debugging. Is not a
+ * required function.
*
* @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
* with other STAs in the IBSS. This is only used in IBSS mode. This
* function is optional if the firmware/hardware takes full care of
* TSF synchronization.
*
- * @beacon_update: Setup beacon data for IBSS beacons. Unlike access point,
- * IBSS uses a fixed beacon frame which is configured using this
- * function.
- * If the driver returns success (0) from this callback, it owns
- * the skb. That means the driver is responsible to kfree_skb() it.
- * The control structure is not dynamically allocated. That means the
- * driver does not own the pointer and if it needs it somewhere
- * outside of the context of this function, it must copy it
- * somewhere else.
- * This handler is required only for IBSS mode.
- *
* @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
* This is needed only for IBSS mode and the result of this function is
* used to determine whether to reply to Probe Requests.
- *
- * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic.
+ * Returns non-zero if this device sent the last beacon.
*
* @ampdu_action: Perform a certain A-MPDU action
* The RA/TID combination determines the destination and TID we want
* the ampdu action to be performed for. The action is defined through
* ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
- * is the first frame we expect to perform the action on. notice
+ * is the first frame we expect to perform the action on. Notice
* that TX/RX_STOP can pass NULL for this parameter.
+ * Returns a negative error code on failure.
*/
struct ieee80211_ops {
int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
struct ieee80211_if_init_conf *conf);
void (*remove_interface)(struct ieee80211_hw *hw,
struct ieee80211_if_init_conf *conf);
- int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
+ int (*config)(struct ieee80211_hw *hw, u32 changed);
int (*config_interface)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_if_conf *conf);
unsigned int changed_flags,
unsigned int *total_flags,
int mc_count, struct dev_addr_list *mc_list);
- int (*set_tim)(struct ieee80211_hw *hw, int aid, int set);
+ int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
+ bool set);
int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
- const u8 *local_address, const u8 *address,
+ struct ieee80211_vif *vif, struct ieee80211_sta *sta,
struct ieee80211_key_conf *key);
void (*update_tkip_key)(struct ieee80211_hw *hw,
struct ieee80211_key_conf *conf, const u8 *address,
u32 iv32, u16 *phase1key);
- int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len);
+ int (*hw_scan)(struct ieee80211_hw *hw,
+ struct cfg80211_scan_request *req);
int (*get_stats)(struct ieee80211_hw *hw,
struct ieee80211_low_level_stats *stats);
void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
u32 *iv32, u16 *iv16);
int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
- int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
- int (*set_retry_limit)(struct ieee80211_hw *hw,
- u32 short_retry, u32 long_retr);
void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
- enum sta_notify_cmd, const u8 *addr);
+ enum sta_notify_cmd, struct ieee80211_sta *sta);
int (*conf_tx)(struct ieee80211_hw *hw, u16 queue,
const struct ieee80211_tx_queue_params *params);
int (*get_tx_stats)(struct ieee80211_hw *hw,
struct ieee80211_tx_queue_stats *stats);
u64 (*get_tsf)(struct ieee80211_hw *hw);
+ void (*set_tsf)(struct ieee80211_hw *hw, u64 tsf);
void (*reset_tsf)(struct ieee80211_hw *hw);
- int (*beacon_update)(struct ieee80211_hw *hw,
- struct sk_buff *skb);
int (*tx_last_beacon)(struct ieee80211_hw *hw);
int (*ampdu_action)(struct ieee80211_hw *hw,
enum ieee80211_ampdu_mlme_action action,
- const u8 *addr, u16 tid, u16 *ssn);
+ struct ieee80211_sta *sta, u16 tid, u16 *ssn);
};
/**
*
* This function frees everything that was allocated, including the
* private data for the driver. You must call ieee80211_unregister_hw()
- * before calling this function
+ * before calling this function.
*
* @hw: the hardware to free
*/
struct sk_buff *skb);
/**
- * ieee80211_tx_status_irqsafe - irq-safe transmit status callback
+ * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
*
* Like ieee80211_tx_status() but can be called in IRQ context
* (internally defers to a tasklet.)
* ieee80211_beacon_get - beacon generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
- * @control: will be filled with information needed to send this beacon.
*
* If the beacon frames are generated by the host system (i.e., not in
* hardware/firmware), the low-level driver uses this function to receive
* the next beacon frame from the 802.11 code. The low-level is responsible
* for calling this function before beacon data is needed (e.g., based on
* hardware interrupt). Returned skb is used only once and low-level driver
- * is responsible of freeing it.
+ * is responsible for freeing it.
*/
struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
struct ieee80211_vif *vif);
* ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
* @hw: pointer as obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
- * @control: will be filled with information needed to send returned frame.
*
* Function for accessing buffered broadcast and multicast frames. If
* hardware/firmware does not implement buffering of broadcast/multicast
unsigned int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
/**
- * ieee80211_get_hdrlen - get header length from frame control
- *
- * This function returns the 802.11 header length in bytes (not including
- * encryption headers.)
- *
- * @fc: the frame control field (in CPU endianness)
- */
-int ieee80211_get_hdrlen(u16 fc);
-
-/**
* ieee80211_hdrlen - get header length in bytes from frame control
* @fc: frame control field in little-endian format
*/
*
* @keyconf: the parameter passed with the set key
* @skb: the skb for which the key is needed
- * @rc4key: a buffer to which the key will be written
+ * @type: TBD
+ * @key: a buffer to which the key will be written
*/
void ieee80211_get_tkip_key(struct ieee80211_key_conf *keyconf,
struct sk_buff *skb,
void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
/**
+ * ieee80211_queue_stopped - test status of the queue
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @queue: queue number (counted from zero).
+ *
+ * Drivers should use this function instead of netif_stop_queue.
+ */
+
+int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
+
+/**
* ieee80211_stop_queues - stop all queues
* @hw: pointer as obtained from ieee80211_alloc_hw().
*
* mac80211 that the scan finished.
*
* @hw: the hardware that finished the scan
+ * @aborted: set to true if scan was aborted
*/
-void ieee80211_scan_completed(struct ieee80211_hw *hw);
+void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted);
/**
- * ieee80211_iterate_active_interfaces- iterate active interfaces
+ * ieee80211_iterate_active_interfaces - iterate active interfaces
*
* This function iterates over the interfaces associated with a given
* hardware that are currently active and calls the callback for them.
* @hw: pointer as obtained from ieee80211_alloc_hw().
* @ra: receiver address of the BA session recipient
* @tid: the TID to BA on.
- * @return: success if addBA request was sent, failure otherwise
+ *
+ * Return: success if addBA request was sent, failure otherwise
*
* Although mac80211/low level driver/user space application can estimate
* the need to start aggregation on a certain RA/TID, the session level
*
* This function must be called by low level driver once it has
* finished with preparations for the BA session.
- * This version of the function is irq safe.
+ * This version of the function is IRQ-safe.
*/
void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
u16 tid);
* @ra: receiver address of the BA session recipient
* @tid: the TID to stop BA.
* @initiator: if indicates initiator DELBA frame will be sent.
- * @return: error if no sta with matching da found, success otherwise
+ *
+ * Return: error if no sta with matching da found, success otherwise
*
* Although mac80211/low level driver/user space application can estimate
* the need to stop aggregation on a certain RA/TID, the session level
*
* This function must be called by low level driver once it has
* finished with preparations for the BA session tear down.
- * This version of the function is irq safe.
+ * This version of the function is IRQ-safe.
*/
void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
u16 tid);
/**
- * ieee80211_notify_mac - low level driver notification
- * @hw: pointer as obtained from ieee80211_alloc_hw().
- * @notification_types: enum ieee80211_notification_types
+ * ieee80211_find_sta - find a station
+ *
+ * @hw: pointer as obtained from ieee80211_alloc_hw()
+ * @addr: station's address
+ *
+ * This function must be called under RCU lock and the
+ * resulting pointer is only valid under RCU lock as well.
+ */
+struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_hw *hw,
+ const u8 *addr);
+
+
+/* Rate control API */
+
+/**
+ * struct ieee80211_tx_rate_control - rate control information for/from RC algo
*
- * This function must be called by low level driver to inform mac80211 of
- * low level driver status change or force mac80211 to re-assoc for low
- * level driver internal error that require re-assoc.
+ * @hw: The hardware the algorithm is invoked for.
+ * @sband: The band this frame is being transmitted on.
+ * @bss_conf: the current BSS configuration
+ * @reported_rate: The rate control algorithm can fill this in to indicate
+ * which rate should be reported to userspace as the current rate and
+ * used for rate calculations in the mesh network.
+ * @rts: whether RTS will be used for this frame because it is longer than the
+ * RTS threshold
+ * @short_preamble: whether mac80211 will request short-preamble transmission
+ * if the selected rate supports it
+ * @max_rate_idx: user-requested maximum rate (not MCS for now)
+ * @skb: the skb that will be transmitted, the control information in it needs
+ * to be filled in
*/
-void ieee80211_notify_mac(struct ieee80211_hw *hw,
- enum ieee80211_notification_types notif_type);
+struct ieee80211_tx_rate_control {
+ struct ieee80211_hw *hw;
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_bss_conf *bss_conf;
+ struct sk_buff *skb;
+ struct ieee80211_tx_rate reported_rate;
+ bool rts, short_preamble;
+ u8 max_rate_idx;
+};
+
+struct rate_control_ops {
+ struct module *module;
+ const char *name;
+ void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
+ void (*free)(void *priv);
+
+ void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
+ void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
+ struct ieee80211_sta *sta, void *priv_sta);
+ void (*free_sta)(void *priv, struct ieee80211_sta *sta,
+ void *priv_sta);
+
+ void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
+ struct ieee80211_sta *sta, void *priv_sta,
+ struct sk_buff *skb);
+ void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
+ struct ieee80211_tx_rate_control *txrc);
+
+ void (*add_sta_debugfs)(void *priv, void *priv_sta,
+ struct dentry *dir);
+ void (*remove_sta_debugfs)(void *priv, void *priv_sta);
+};
+
+static inline int rate_supported(struct ieee80211_sta *sta,
+ enum ieee80211_band band,
+ int index)
+{
+ return (sta == NULL || sta->supp_rates[band] & BIT(index));
+}
+
+static inline s8
+rate_lowest_index(struct ieee80211_supported_band *sband,
+ struct ieee80211_sta *sta)
+{
+ int i;
+
+ for (i = 0; i < sband->n_bitrates; i++)
+ if (rate_supported(sta, sband->band, i))
+ return i;
+
+ /* warn when we cannot find a rate. */
+ WARN_ON(1);
+
+ return 0;
+}
+
+
+int ieee80211_rate_control_register(struct rate_control_ops *ops);
+void ieee80211_rate_control_unregister(struct rate_control_ops *ops);
+
+static inline bool
+conf_is_ht20(struct ieee80211_conf *conf)
+{
+ return conf->channel_type == NL80211_CHAN_HT20;
+}
+
+static inline bool
+conf_is_ht40_minus(struct ieee80211_conf *conf)
+{
+ return conf->channel_type == NL80211_CHAN_HT40MINUS;
+}
+
+static inline bool
+conf_is_ht40_plus(struct ieee80211_conf *conf)
+{
+ return conf->channel_type == NL80211_CHAN_HT40PLUS;
+}
+
+static inline bool
+conf_is_ht40(struct ieee80211_conf *conf)
+{
+ return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf);
+}
+
+static inline bool
+conf_is_ht(struct ieee80211_conf *conf)
+{
+ return conf->channel_type != NL80211_CHAN_NO_HT;
+}
+
#endif /* MAC80211_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff