USB: serial: ftdi: enable UART detection on gnICE JTAG adaptors blacklist interface0

[safe/jmp/linux-2.6] / drivers / usb / serial / ftdi_sio.h

diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index 70703b7..daaf63d 100644 (file)
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -40,6 +40,9 @@
 /* AlphaMicro Components AMC-232USB01 device */
 #define FTDI_AMC232_PID 0xFF00 /* Product Id */
 
+/* www.candapter.com Ewert Energy Systems CANdapter device */
+#define FTDI_CANDAPTER_PID 0x9F80 /* Product Id */
+
 /* SCS HF Radio Modems PID's (http://www.scs-ptc.com) */
 /* the VID is the standard ftdi vid (FTDI_VID) */
 #define FTDI_SCS_DEVICE_0_PID 0xD010    /* SCS PTC-IIusb */
@@ -841,6 +844,9 @@
 #define TML_VID                        0x1B91  /* Vendor ID */
 #define TML_USB_SERIAL_PID     0x0064  /* USB - Serial Converter */
 
+/* NDI Polaris System */
+#define FTDI_NDI_HUC_PID        0xDA70
+
 /* Propox devices */
 #define FTDI_PROPOX_JTAGCABLEII_PID    0xD738
 
@@ -851,6 +857,10 @@
 #define FTDI_DOMINTELL_DGQG_PID        0xEF50  /* Master */
 #define FTDI_DOMINTELL_DUSB_PID        0xEF51  /* DUSB01 module */
 
+/* Alti-2 products  http://www.alti-2.com */
+#define ALTI2_VID      0x1BC9
+#define ALTI2_N3_PID   0x6001  /* Neptune 3 */
+
 /* Commands */
 #define FTDI_SIO_RESET                 0 /* Reset the port */
 #define FTDI_SIO_MODEM_CTRL    1 /* Set the modem control register */
@@ -878,6 +888,31 @@
 #define RATOC_PRODUCT_ID_USB60F        0xb020
 
 /*
+ * DIEBOLD BCS SE923
+ */
+#define DIEBOLD_BCS_SE923_PID  0xfb99
+
+/*
+ * Atmel STK541
+ */
+#define ATMEL_VID              0x03eb /* Vendor ID */
+#define STK541_PID             0x2109 /* Zigbee Controller */
+
+/*
+ * Dresden Elektronic Sensor Terminal Board
+ */
+#define DE_VID                 0x1cf1 /* Vendor ID */
+#define STB_PID                        0x0001 /* Sensor Terminal Board */
+#define WHT_PID                        0x0004 /* Wireless Handheld Terminal */
+
+/*
+ * Blackfin gnICE JTAG
+ * http://docs.blackfin.uclinux.org/doku.php?id=hw:jtag:gnice
+ */
+#define ADI_VID                0x0456
+#define ADI_GNICE_PID          0xF000
+
+/*
  *   BmRequestType:  1100 0000b
  *   bRequest:       FTDI_E2_READ
  *   wValue:         0