* USB Cypress M8 driver
*
* Copyright (C) 2004
- * Lonnie Mendez (dignome@gmail.com)
+ * Lonnie Mendez (dignome@gmail.com)
* Copyright (C) 2003,2004
* Neil Whelchel (koyama@firstlight.net)
*
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
- * See Documentation/usb/usb-serial.txt for more information on using this driver
+ * See Documentation/usb/usb-serial.txt for more information on using this
+ * driver
*
* See http://geocities.com/i0xox0i for information on this driver and the
* earthmate usb device.
*
* Lonnie Mendez <dignome@gmail.com>
* 4-29-2005
- * Fixed problem where setting or retreiving the serial config would fail with
- * EPIPE. Removed CRTS toggling so the driver behaves more like other usbserial
- * adapters. Issued new interval of 1ms instead of the default 10ms. As a
- * result, transfer speed has been substantially increased. From avg. 850bps to
- * avg. 3300bps. initial termios has also been modified. Cleaned up code and
- * formatting issues so it is more readable. Replaced the C++ style comments.
+ * Fixed problem where setting or retreiving the serial config would fail
+ * with EPIPE. Removed CRTS toggling so the driver behaves more like
+ * other usbserial adapters. Issued new interval of 1ms instead of the
+ * default 10ms. As a result, transfer speed has been substantially
+ * increased from avg. 850bps to avg. 3300bps. initial termios has also
+ * been modified. Cleaned up code and formatting issues so it is more
+ * readable. Replaced the C++ style comments.
*
* Lonnie Mendez <dignome@gmail.com>
* 12-15-2004
*
*/
-/* Thanks to Neil Whelchel for writing the first cypress m8 implementation for linux. */
+/* Thanks to Neil Whelchel for writing the first cypress m8 implementation
+ for linux. */
/* Thanks to cypress for providing references for the hid reports. */
/* Thanks to Jiang Zhang for providing links and for general help. */
-/* Code originates and was built up from ftdi_sio, belkin, pl2303 and others. */
+/* Code originates and was built up from ftdi_sio, belkin, pl2303 and others.*/
#include <linux/kernel.h>
#include <linux/usb/serial.h>
#include <linux/serial.h>
#include <linux/delay.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
+#include <asm/unaligned.h>
#include "cypress_m8.h"
-#ifdef CONFIG_USB_SERIAL_DEBUG
- static int debug = 1;
-#else
- static int debug;
-#endif
+static int debug;
static int stats;
static int interval;
+static int unstable_bauds;
/*
* Version Information
#define CYPRESS_BUF_SIZE 1024
#define CYPRESS_CLOSING_WAIT (30*HZ)
-static struct usb_device_id id_table_earthmate [] = {
+static const struct usb_device_id id_table_earthmate[] = {
{ USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB) },
{ USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB_LT20) },
{ } /* Terminating entry */
};
-static struct usb_device_id id_table_cyphidcomrs232 [] = {
+static const struct usb_device_id id_table_cyphidcomrs232[] = {
{ USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) },
+ { USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) },
{ } /* Terminating entry */
};
-static struct usb_device_id id_table_nokiaca42v2 [] = {
+static const struct usb_device_id id_table_nokiaca42v2[] = {
{ USB_DEVICE(VENDOR_ID_DAZZLE, PRODUCT_ID_CA42) },
{ } /* Terminating entry */
};
-static struct usb_device_id id_table_combined [] = {
+static const struct usb_device_id id_table_combined[] = {
{ USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB) },
{ USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB_LT20) },
{ USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) },
+ { USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) },
{ USB_DEVICE(VENDOR_ID_DAZZLE, PRODUCT_ID_CA42) },
{ } /* Terminating entry */
};
-MODULE_DEVICE_TABLE (usb, id_table_combined);
+MODULE_DEVICE_TABLE(usb, id_table_combined);
static struct usb_driver cypress_driver = {
.name = "cypress",
.no_dynamic_id = 1,
};
+enum packet_format {
+ packet_format_1, /* b0:status, b1:payload count */
+ packet_format_2 /* b0[7:3]:status, b0[2:0]:payload count */
+};
+
struct cypress_private {
spinlock_t lock; /* private lock */
int chiptype; /* identifier of device, for quirks/etc */
__u8 current_status; /* received from last read - info on dsr,cts,cd,ri,etc */
__u8 current_config; /* stores the current configuration byte */
__u8 rx_flags; /* throttling - used from whiteheat/ftdi_sio */
- int baud_rate; /* stores current baud rate in integer form */
- int cbr_mask; /* stores current baud rate in masked form */
+ enum packet_format pkt_fmt; /* format to use for packet send / receive */
+ int get_cfg_unsafe; /* If true, the CYPRESS_GET_CONFIG is unsafe */
+ int baud_rate; /* stores current baud rate in
+ integer form */
int isthrottled; /* if throttled, discard reads */
wait_queue_head_t delta_msr_wait; /* used for TIOCMIWAIT */
char prev_status, diff_status; /* used for TIOCMIWAIT */
- /* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */
+ /* we pass a pointer to this as the argument sent to
+ cypress_set_termios old_termios */
struct ktermios tmp_termios; /* stores the old termios settings */
};
};
/* function prototypes for the Cypress USB to serial device */
-static int cypress_earthmate_startup (struct usb_serial *serial);
-static int cypress_hidcom_startup (struct usb_serial *serial);
-static int cypress_ca42v2_startup (struct usb_serial *serial);
-static void cypress_shutdown (struct usb_serial *serial);
-static int cypress_open (struct usb_serial_port *port, struct file *filp);
-static void cypress_close (struct usb_serial_port *port, struct file *filp);
-static int cypress_write (struct usb_serial_port *port, const unsigned char *buf, int count);
-static void cypress_send (struct usb_serial_port *port);
-static int cypress_write_room (struct usb_serial_port *port);
-static int cypress_ioctl (struct usb_serial_port *port, struct file * file, unsigned int cmd, unsigned long arg);
-static void cypress_set_termios (struct usb_serial_port *port, struct ktermios * old);
-static int cypress_tiocmget (struct usb_serial_port *port, struct file *file);
-static int cypress_tiocmset (struct usb_serial_port *port, struct file *file, unsigned int set, unsigned int clear);
-static int cypress_chars_in_buffer (struct usb_serial_port *port);
-static void cypress_throttle (struct usb_serial_port *port);
-static void cypress_unthrottle (struct usb_serial_port *port);
-static void cypress_set_dead (struct usb_serial_port *port);
-static void cypress_read_int_callback (struct urb *urb);
-static void cypress_write_int_callback (struct urb *urb);
-/* baud helper functions */
-static int mask_to_rate (unsigned mask);
-static unsigned rate_to_mask (int rate);
+static int cypress_earthmate_startup(struct usb_serial *serial);
+static int cypress_hidcom_startup(struct usb_serial *serial);
+static int cypress_ca42v2_startup(struct usb_serial *serial);
+static void cypress_release(struct usb_serial *serial);
+static int cypress_open(struct tty_struct *tty, struct usb_serial_port *port);
+static void cypress_close(struct usb_serial_port *port);
+static void cypress_dtr_rts(struct usb_serial_port *port, int on);
+static int cypress_write(struct tty_struct *tty, struct usb_serial_port *port,
+ const unsigned char *buf, int count);
+static void cypress_send(struct usb_serial_port *port);
+static int cypress_write_room(struct tty_struct *tty);
+static int cypress_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg);
+static void cypress_set_termios(struct tty_struct *tty,
+ struct usb_serial_port *port, struct ktermios *old);
+static int cypress_tiocmget(struct tty_struct *tty, struct file *file);
+static int cypress_tiocmset(struct tty_struct *tty, struct file *file,
+ unsigned int set, unsigned int clear);
+static int cypress_chars_in_buffer(struct tty_struct *tty);
+static void cypress_throttle(struct tty_struct *tty);
+static void cypress_unthrottle(struct tty_struct *tty);
+static void cypress_set_dead(struct usb_serial_port *port);
+static void cypress_read_int_callback(struct urb *urb);
+static void cypress_write_int_callback(struct urb *urb);
/* write buffer functions */
static struct cypress_buf *cypress_buf_alloc(unsigned int size);
-static void cypress_buf_free(struct cypress_buf *cb);
-static void cypress_buf_clear(struct cypress_buf *cb);
-static unsigned int cypress_buf_data_avail(struct cypress_buf *cb);
-static unsigned int cypress_buf_space_avail(struct cypress_buf *cb);
-static unsigned int cypress_buf_put(struct cypress_buf *cb, const char *buf, unsigned int count);
-static unsigned int cypress_buf_get(struct cypress_buf *cb, char *buf, unsigned int count);
+static void cypress_buf_free(struct cypress_buf *cb);
+static void cypress_buf_clear(struct cypress_buf *cb);
+static unsigned int cypress_buf_data_avail(struct cypress_buf *cb);
+static unsigned int cypress_buf_space_avail(struct cypress_buf *cb);
+static unsigned int cypress_buf_put(struct cypress_buf *cb,
+ const char *buf, unsigned int count);
+static unsigned int cypress_buf_get(struct cypress_buf *cb,
+ char *buf, unsigned int count);
static struct usb_serial_driver cypress_earthmate_device = {
.description = "DeLorme Earthmate USB",
.usb_driver = &cypress_driver,
.id_table = id_table_earthmate,
- .num_interrupt_in = 1,
- .num_interrupt_out = 1,
- .num_bulk_in = NUM_DONT_CARE,
- .num_bulk_out = NUM_DONT_CARE,
.num_ports = 1,
.attach = cypress_earthmate_startup,
- .shutdown = cypress_shutdown,
+ .release = cypress_release,
.open = cypress_open,
.close = cypress_close,
+ .dtr_rts = cypress_dtr_rts,
.write = cypress_write,
.write_room = cypress_write_room,
.ioctl = cypress_ioctl,
.description = "HID->COM RS232 Adapter",
.usb_driver = &cypress_driver,
.id_table = id_table_cyphidcomrs232,
- .num_interrupt_in = 1,
- .num_interrupt_out = 1,
- .num_bulk_in = NUM_DONT_CARE,
- .num_bulk_out = NUM_DONT_CARE,
.num_ports = 1,
.attach = cypress_hidcom_startup,
- .shutdown = cypress_shutdown,
+ .release = cypress_release,
.open = cypress_open,
.close = cypress_close,
+ .dtr_rts = cypress_dtr_rts,
.write = cypress_write,
.write_room = cypress_write_room,
.ioctl = cypress_ioctl,
static struct usb_serial_driver cypress_ca42v2_device = {
.driver = {
.owner = THIS_MODULE,
- .name = "nokiaca42v2",
+ .name = "nokiaca42v2",
},
.description = "Nokia CA-42 V2 Adapter",
.usb_driver = &cypress_driver,
.id_table = id_table_nokiaca42v2,
- .num_interrupt_in = 1,
- .num_interrupt_out = 1,
- .num_bulk_in = NUM_DONT_CARE,
- .num_bulk_out = NUM_DONT_CARE,
.num_ports = 1,
.attach = cypress_ca42v2_startup,
- .shutdown = cypress_shutdown,
+ .release = cypress_release,
.open = cypress_open,
.close = cypress_close,
+ .dtr_rts = cypress_dtr_rts,
.write = cypress_write,
.write_room = cypress_write_room,
.ioctl = cypress_ioctl,
*****************************************************************************/
+static int analyze_baud_rate(struct usb_serial_port *port, speed_t new_rate)
+{
+ struct cypress_private *priv;
+ priv = usb_get_serial_port_data(port);
+
+ if (unstable_bauds)
+ return new_rate;
+
+ /*
+ * The general purpose firmware for the Cypress M8 allows for
+ * a maximum speed of 57600bps (I have no idea whether DeLorme
+ * chose to use the general purpose firmware or not), if you
+ * need to modify this speed setting for your own project
+ * please add your own chiptype and modify the code likewise.
+ * The Cypress HID->COM device will work successfully up to
+ * 115200bps (but the actual throughput is around 3kBps).
+ */
+ if (port->serial->dev->speed == USB_SPEED_LOW) {
+ /*
+ * Mike Isely <isely@pobox.com> 2-Feb-2008: The
+ * Cypress app note that describes this mechanism
+ * states the the low-speed part can't handle more
+ * than 800 bytes/sec, in which case 4800 baud is the
+ * safest speed for a part like that.
+ */
+ if (new_rate > 4800) {
+ dbg("%s - failed setting baud rate, device incapable "
+ "speed %d", __func__, new_rate);
+ return -1;
+ }
+ }
+ switch (priv->chiptype) {
+ case CT_EARTHMATE:
+ if (new_rate <= 600) {
+ /* 300 and 600 baud rates are supported under
+ * the generic firmware, but are not used with
+ * NMEA and SiRF protocols */
+ dbg("%s - failed setting baud rate, unsupported speed "
+ "of %d on Earthmate GPS", __func__, new_rate);
+ return -1;
+ }
+ break;
+ default:
+ break;
+ }
+ return new_rate;
+}
+
+
/* This function can either set or retrieve the current serial line settings */
-static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_mask, int data_bits, int stop_bits,
- int parity_enable, int parity_type, int reset, int cypress_request_type)
+static int cypress_serial_control(struct tty_struct *tty,
+ struct usb_serial_port *port, speed_t baud_rate, int data_bits,
+ int stop_bits, int parity_enable, int parity_type, int reset,
+ int cypress_request_type)
{
int new_baudrate = 0, retval = 0, tries = 0;
struct cypress_private *priv;
- __u8 feature_buffer[8];
+ u8 *feature_buffer;
+ const unsigned int feature_len = 5;
unsigned long flags;
- dbg("%s", __FUNCTION__);
-
+ dbg("%s", __func__);
+
priv = usb_get_serial_port_data(port);
if (!priv->comm_is_ok)
return -ENODEV;
- switch(cypress_request_type) {
- case CYPRESS_SET_CONFIG:
-
- /*
- * The general purpose firmware for the Cypress M8 allows for a maximum speed
- * of 57600bps (I have no idea whether DeLorme chose to use the general purpose
- * firmware or not), if you need to modify this speed setting for your own
- * project please add your own chiptype and modify the code likewise. The
- * Cypress HID->COM device will work successfully up to 115200bps (but the
- * actual throughput is around 3kBps).
- */
- if (baud_mask != priv->cbr_mask) {
- dbg("%s - baud rate is changing", __FUNCTION__);
- if ( priv->chiptype == CT_EARTHMATE ) {
- /* 300 and 600 baud rates are supported under the generic firmware,
- * but are not used with NMEA and SiRF protocols */
-
- if ( (baud_mask == B300) || (baud_mask == B600) ) {
- err("%s - failed setting baud rate, unsupported speed",
- __FUNCTION__);
- new_baudrate = priv->baud_rate;
- } else if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) {
- err("%s - failed setting baud rate, unsupported speed",
- __FUNCTION__);
- new_baudrate = priv->baud_rate;
- }
- } else if (priv->chiptype == CT_CYPHIDCOM) {
- if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) {
- err("%s - failed setting baud rate, unsupported speed",
- __FUNCTION__);
- new_baudrate = priv->baud_rate;
- }
- } else if (priv->chiptype == CT_CA42V2) {
- if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) {
- err("%s - failed setting baud rate, unsupported speed",
- __FUNCTION__);
- new_baudrate = priv->baud_rate;
- }
- } else if (priv->chiptype == CT_GENERIC) {
- if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) {
- err("%s - failed setting baud rate, unsupported speed",
- __FUNCTION__);
- new_baudrate = priv->baud_rate;
- }
- } else {
- info("%s - please define your chiptype", __FUNCTION__);
- new_baudrate = priv->baud_rate;
- }
- } else { /* baud rate not changing, keep the old */
- new_baudrate = priv->baud_rate;
- }
- dbg("%s - baud rate is being sent as %d", __FUNCTION__, new_baudrate);
-
- memset(feature_buffer, 0, 8);
- /* fill the feature_buffer with new configuration */
- *((u_int32_t *)feature_buffer) = new_baudrate;
-
- feature_buffer[4] |= data_bits; /* assign data bits in 2 bit space ( max 3 ) */
- /* 1 bit gap */
- feature_buffer[4] |= (stop_bits << 3); /* assign stop bits in 1 bit space */
- feature_buffer[4] |= (parity_enable << 4); /* assign parity flag in 1 bit space */
- feature_buffer[4] |= (parity_type << 5); /* assign parity type in 1 bit space */
- /* 1 bit gap */
- feature_buffer[4] |= (reset << 7); /* assign reset at end of byte, 1 bit space */
-
- dbg("%s - device is being sent this feature report:", __FUNCTION__);
- dbg("%s - %02X - %02X - %02X - %02X - %02X", __FUNCTION__, feature_buffer[0], feature_buffer[1],
- feature_buffer[2], feature_buffer[3], feature_buffer[4]);
-
- do {
- retval = usb_control_msg (port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0),
- HID_REQ_SET_REPORT, USB_DIR_OUT | USB_RECIP_INTERFACE | USB_TYPE_CLASS,
- 0x0300, 0, feature_buffer, 8, 500);
-
- if (tries++ >= 3)
- break;
-
- } while (retval != 8 && retval != -ENODEV);
-
- if (retval != 8) {
- err("%s - failed sending serial line settings - %d", __FUNCTION__, retval);
- cypress_set_dead(port);
- } else {
- spin_lock_irqsave(&priv->lock, flags);
- priv->baud_rate = new_baudrate;
- priv->cbr_mask = baud_mask;
- priv->current_config = feature_buffer[4];
- spin_unlock_irqrestore(&priv->lock, flags);
- }
- break;
- case CYPRESS_GET_CONFIG:
- dbg("%s - retreiving serial line settings", __FUNCTION__);
- /* set initial values in feature buffer */
- memset(feature_buffer, 0, 8);
-
- do {
- retval = usb_control_msg (port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0),
- HID_REQ_GET_REPORT, USB_DIR_IN | USB_RECIP_INTERFACE | USB_TYPE_CLASS,
- 0x0300, 0, feature_buffer, 8, 500);
-
- if (tries++ >= 3)
- break;
-
- } while (retval != 5 && retval != -ENODEV);
-
- if (retval != 5) {
- err("%s - failed to retrieve serial line settings - %d", __FUNCTION__, retval);
- cypress_set_dead(port);
- return retval;
- } else {
- spin_lock_irqsave(&priv->lock, flags);
-
- /* store the config in one byte, and later use bit masks to check values */
- priv->current_config = feature_buffer[4];
- priv->baud_rate = *((u_int32_t *)feature_buffer);
-
- if ( (priv->cbr_mask = rate_to_mask(priv->baud_rate)) == 0x40)
- dbg("%s - failed setting the baud mask (not defined)", __FUNCTION__);
- spin_unlock_irqrestore(&priv->lock, flags);
+ feature_buffer = kcalloc(feature_len, sizeof(u8), GFP_KERNEL);
+ if (!feature_buffer)
+ return -ENOMEM;
+
+ switch (cypress_request_type) {
+ case CYPRESS_SET_CONFIG:
+ /* 0 means 'Hang up' so doesn't change the true bit rate */
+ new_baudrate = priv->baud_rate;
+ if (baud_rate && baud_rate != priv->baud_rate) {
+ dbg("%s - baud rate is changing", __func__);
+ retval = analyze_baud_rate(port, baud_rate);
+ if (retval >= 0) {
+ new_baudrate = retval;
+ dbg("%s - New baud rate set to %d",
+ __func__, new_baudrate);
}
+ }
+ dbg("%s - baud rate is being sent as %d",
+ __func__, new_baudrate);
+
+ /* fill the feature_buffer with new configuration */
+ put_unaligned_le32(new_baudrate, feature_buffer);
+ feature_buffer[4] |= data_bits; /* assign data bits in 2 bit space ( max 3 ) */
+ /* 1 bit gap */
+ feature_buffer[4] |= (stop_bits << 3); /* assign stop bits in 1 bit space */
+ feature_buffer[4] |= (parity_enable << 4); /* assign parity flag in 1 bit space */
+ feature_buffer[4] |= (parity_type << 5); /* assign parity type in 1 bit space */
+ /* 1 bit gap */
+ feature_buffer[4] |= (reset << 7); /* assign reset at end of byte, 1 bit space */
+
+ dbg("%s - device is being sent this feature report:",
+ __func__);
+ dbg("%s - %02X - %02X - %02X - %02X - %02X", __func__,
+ feature_buffer[0], feature_buffer[1],
+ feature_buffer[2], feature_buffer[3],
+ feature_buffer[4]);
+
+ do {
+ retval = usb_control_msg(port->serial->dev,
+ usb_sndctrlpipe(port->serial->dev, 0),
+ HID_REQ_SET_REPORT,
+ USB_DIR_OUT | USB_RECIP_INTERFACE | USB_TYPE_CLASS,
+ 0x0300, 0, feature_buffer,
+ feature_len, 500);
+
+ if (tries++ >= 3)
+ break;
+
+ } while (retval != feature_len &&
+ retval != -ENODEV);
+
+ if (retval != feature_len) {
+ dev_err(&port->dev, "%s - failed sending serial "
+ "line settings - %d\n", __func__, retval);
+ cypress_set_dead(port);
+ } else {
+ spin_lock_irqsave(&priv->lock, flags);
+ priv->baud_rate = new_baudrate;
+ priv->current_config = feature_buffer[4];
+ spin_unlock_irqrestore(&priv->lock, flags);
+ /* If we asked for a speed change encode it */
+ if (baud_rate)
+ tty_encode_baud_rate(tty,
+ new_baudrate, new_baudrate);
+ }
+ break;
+ case CYPRESS_GET_CONFIG:
+ if (priv->get_cfg_unsafe) {
+ /* Not implemented for this device,
+ and if we try to do it we're likely
+ to crash the hardware. */
+ retval = -ENOTTY;
+ goto out;
+ }
+ dbg("%s - retreiving serial line settings", __func__);
+ do {
+ retval = usb_control_msg(port->serial->dev,
+ usb_rcvctrlpipe(port->serial->dev, 0),
+ HID_REQ_GET_REPORT,
+ USB_DIR_IN | USB_RECIP_INTERFACE | USB_TYPE_CLASS,
+ 0x0300, 0, feature_buffer,
+ feature_len, 500);
+
+ if (tries++ >= 3)
+ break;
+ } while (retval != feature_len
+ && retval != -ENODEV);
+
+ if (retval != feature_len) {
+ dev_err(&port->dev, "%s - failed to retrieve serial "
+ "line settings - %d\n", __func__, retval);
+ cypress_set_dead(port);
+ goto out;
+ } else {
+ spin_lock_irqsave(&priv->lock, flags);
+ /* store the config in one byte, and later
+ use bit masks to check values */
+ priv->current_config = feature_buffer[4];
+ priv->baud_rate = get_unaligned_le32(feature_buffer);
+ spin_unlock_irqrestore(&priv->lock, flags);
+ }
}
spin_lock_irqsave(&priv->lock, flags);
++priv->cmd_count;
spin_unlock_irqrestore(&priv->lock, flags);
-
+out:
+ kfree(feature_buffer);
return retval;
} /* cypress_serial_control */
priv->comm_is_ok = 0;
spin_unlock_irqrestore(&priv->lock, flags);
- err("cypress_m8 suspending failing port %d - interval might be too short",
- port->number);
+ dev_err(&port->dev, "cypress_m8 suspending failing port %d - "
+ "interval might be too short\n", port->number);
}
-/* given a baud mask, it will return integer baud on success */
-static int mask_to_rate (unsigned mask)
-{
- int rate;
-
- switch (mask) {
- case B0: rate = 0; break;
- case B300: rate = 300; break;
- case B600: rate = 600; break;
- case B1200: rate = 1200; break;
- case B2400: rate = 2400; break;
- case B4800: rate = 4800; break;
- case B9600: rate = 9600; break;
- case B19200: rate = 19200; break;
- case B38400: rate = 38400; break;
- case B57600: rate = 57600; break;
- case B115200: rate = 115200; break;
- default: rate = -1;
- }
-
- return rate;
-}
-
-
-static unsigned rate_to_mask (int rate)
-{
- unsigned mask;
-
- switch (rate) {
- case 0: mask = B0; break;
- case 300: mask = B300; break;
- case 600: mask = B600; break;
- case 1200: mask = B1200; break;
- case 2400: mask = B2400; break;
- case 4800: mask = B4800; break;
- case 9600: mask = B9600; break;
- case 19200: mask = B19200; break;
- case 38400: mask = B38400; break;
- case 57600: mask = B57600; break;
- case 115200: mask = B115200; break;
- default: mask = 0x40;
- }
-
- return mask;
-}
/*****************************************************************************
* Cypress serial driver functions
*****************************************************************************/
-static int generic_startup (struct usb_serial *serial)
+static int generic_startup(struct usb_serial *serial)
{
struct cypress_private *priv;
struct usb_serial_port *port = serial->port[0];
- dbg("%s - port %d", __FUNCTION__, port->number);
+ dbg("%s - port %d", __func__, port->number);
- priv = kzalloc(sizeof (struct cypress_private), GFP_KERNEL);
+ priv = kzalloc(sizeof(struct cypress_private), GFP_KERNEL);
if (!priv)
return -ENOMEM;
return -ENOMEM;
}
init_waitqueue_head(&priv->delta_msr_wait);
-
- usb_reset_configuration (serial->dev);
-
+
+ usb_reset_configuration(serial->dev);
+
priv->cmd_ctrl = 0;
priv->line_control = 0;
priv->termios_initialized = 0;
priv->rx_flags = 0;
- priv->cbr_mask = B300;
+ /* Default packet format setting is determined by packet size.
+ Anything with a size larger then 9 must have a separate
+ count field since the 3 bit count field is otherwise too
+ small. Otherwise we can use the slightly more compact
+ format. This is in accordance with the cypress_m8 serial
+ converter app note. */
+ if (port->interrupt_out_size > 9)
+ priv->pkt_fmt = packet_format_1;
+ else
+ priv->pkt_fmt = packet_format_2;
+
if (interval > 0) {
priv->write_urb_interval = interval;
priv->read_urb_interval = interval;
dbg("%s - port %d read & write intervals forced to %d",
- __FUNCTION__,port->number,interval);
+ __func__, port->number, interval);
} else {
priv->write_urb_interval = port->interrupt_out_urb->interval;
priv->read_urb_interval = port->interrupt_in_urb->interval;
dbg("%s - port %d intervals: read=%d write=%d",
- __FUNCTION__,port->number,
- priv->read_urb_interval,priv->write_urb_interval);
+ __func__, port->number,
+ priv->read_urb_interval, priv->write_urb_interval);
}
usb_set_serial_port_data(port, priv);
-
+
return 0;
}
-static int cypress_earthmate_startup (struct usb_serial *serial)
+static int cypress_earthmate_startup(struct usb_serial *serial)
{
struct cypress_private *priv;
+ struct usb_serial_port *port = serial->port[0];
- dbg("%s", __FUNCTION__);
+ dbg("%s", __func__);
if (generic_startup(serial)) {
- dbg("%s - Failed setting up port %d", __FUNCTION__,
- serial->port[0]->number);
+ dbg("%s - Failed setting up port %d", __func__,
+ port->number);
return 1;
}
- priv = usb_get_serial_port_data(serial->port[0]);
+ priv = usb_get_serial_port_data(port);
priv->chiptype = CT_EARTHMATE;
+ /* All Earthmate devices use the separated-count packet
+ format! Idiotic. */
+ priv->pkt_fmt = packet_format_1;
+ if (serial->dev->descriptor.idProduct !=
+ cpu_to_le16(PRODUCT_ID_EARTHMATEUSB)) {
+ /* The old original USB Earthmate seemed able to
+ handle GET_CONFIG requests; everything they've
+ produced since that time crashes if this command is
+ attempted :-( */
+ dbg("%s - Marking this device as unsafe for GET_CONFIG "
+ "commands", __func__);
+ priv->get_cfg_unsafe = !0;
+ }
return 0;
} /* cypress_earthmate_startup */
-static int cypress_hidcom_startup (struct usb_serial *serial)
+static int cypress_hidcom_startup(struct usb_serial *serial)
{
struct cypress_private *priv;
- dbg("%s", __FUNCTION__);
+ dbg("%s", __func__);
if (generic_startup(serial)) {
- dbg("%s - Failed setting up port %d", __FUNCTION__,
+ dbg("%s - Failed setting up port %d", __func__,
serial->port[0]->number);
return 1;
}
priv = usb_get_serial_port_data(serial->port[0]);
priv->chiptype = CT_CYPHIDCOM;
-
+
return 0;
} /* cypress_hidcom_startup */
-static int cypress_ca42v2_startup (struct usb_serial *serial)
+static int cypress_ca42v2_startup(struct usb_serial *serial)
{
struct cypress_private *priv;
- dbg("%s", __FUNCTION__);
+ dbg("%s", __func__);
if (generic_startup(serial)) {
- dbg("%s - Failed setting up port %d", __FUNCTION__,
+ dbg("%s - Failed setting up port %d", __func__,
serial->port[0]->number);
return 1;
}
} /* cypress_ca42v2_startup */
-static void cypress_shutdown (struct usb_serial *serial)
+static void cypress_release(struct usb_serial *serial)
{
struct cypress_private *priv;
- dbg ("%s - port %d", __FUNCTION__, serial->port[0]->number);
+ dbg("%s - port %d", __func__, serial->port[0]->number);
/* all open ports are closed at this point */
if (priv) {
cypress_buf_free(priv->buf);
kfree(priv);
- usb_set_serial_port_data(serial->port[0], NULL);
}
}
-static int cypress_open (struct usb_serial_port *port, struct file *filp)
+static int cypress_open(struct tty_struct *tty, struct usb_serial_port *port)
{
struct cypress_private *priv = usb_get_serial_port_data(port);
struct usb_serial *serial = port->serial;
unsigned long flags;
int result = 0;
- dbg("%s - port %d", __FUNCTION__, port->number);
+ dbg("%s - port %d", __func__, port->number);
if (!priv->comm_is_ok)
return -EIO;
priv->rx_flags = 0;
spin_unlock_irqrestore(&priv->lock, flags);
- /* setting to zero could cause data loss */
- port->tty->low_latency = 1;
-
- /* raise both lines and set termios */
- spin_lock_irqsave(&priv->lock, flags);
- priv->line_control = CONTROL_DTR | CONTROL_RTS;
- priv->cmd_ctrl = 1;
- spin_unlock_irqrestore(&priv->lock, flags);
- result = cypress_write(port, NULL, 0);
-
- if (result) {
- dev_err(&port->dev, "%s - failed setting the control lines - error %d\n", __FUNCTION__, result);
- return result;
- } else
- dbg("%s - success setting the control lines", __FUNCTION__);
+ /* Set termios */
+ cypress_send(port);
- cypress_set_termios(port, &priv->tmp_termios);
+ if (tty)
+ cypress_set_termios(tty, port, &priv->tmp_termios);
/* setup the port and start reading from the device */
- if(!port->interrupt_in_urb){
- err("%s - interrupt_in_urb is empty!", __FUNCTION__);
- return(-1);
+ if (!port->interrupt_in_urb) {
+ dev_err(&port->dev, "%s - interrupt_in_urb is empty!\n",
+ __func__);
+ return -1;
}
usb_fill_int_urb(port->interrupt_in_urb, serial->dev,
usb_rcvintpipe(serial->dev, port->interrupt_in_endpointAddress),
- port->interrupt_in_urb->transfer_buffer, port->interrupt_in_urb->transfer_buffer_length,
+ port->interrupt_in_urb->transfer_buffer,
+ port->interrupt_in_urb->transfer_buffer_length,
cypress_read_int_callback, port, priv->read_urb_interval);
result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
- if (result){
- dev_err(&port->dev, "%s - failed submitting read urb, error %d\n", __FUNCTION__, result);
+ if (result) {
+ dev_err(&port->dev,
+ "%s - failed submitting read urb, error %d\n",
+ __func__, result);
cypress_set_dead(port);
}
-
+ port->port.drain_delay = 256;
return result;
} /* cypress_open */
+static void cypress_dtr_rts(struct usb_serial_port *port, int on)
+{
+ struct cypress_private *priv = usb_get_serial_port_data(port);
+ /* drop dtr and rts */
+ spin_lock_irq(&priv->lock);
+ if (on == 0)
+ priv->line_control = 0;
+ else
+ priv->line_control = CONTROL_DTR | CONTROL_RTS;
+ priv->cmd_ctrl = 1;
+ spin_unlock_irq(&priv->lock);
+ cypress_write(NULL, port, NULL, 0);
+}
-static void cypress_close(struct usb_serial_port *port, struct file * filp)
+static void cypress_close(struct usb_serial_port *port)
{
struct cypress_private *priv = usb_get_serial_port_data(port);
- unsigned int c_cflag;
- unsigned long flags;
- int bps;
- long timeout;
- wait_queue_t wait;
- dbg("%s - port %d", __FUNCTION__, port->number);
+ dbg("%s - port %d", __func__, port->number);
- /* wait for data to drain from buffer */
- spin_lock_irqsave(&priv->lock, flags);
- timeout = CYPRESS_CLOSING_WAIT;
- init_waitqueue_entry(&wait, current);
- add_wait_queue(&port->tty->write_wait, &wait);
- for (;;) {
- set_current_state(TASK_INTERRUPTIBLE);
- if (cypress_buf_data_avail(priv->buf) == 0
- || timeout == 0 || signal_pending(current)
- || !usb_get_intfdata(port->serial->interface))
- break;
- spin_unlock_irqrestore(&priv->lock, flags);
- timeout = schedule_timeout(timeout);
- spin_lock_irqsave(&priv->lock, flags);
+ /* writing is potentially harmful, lock must be taken */
+ mutex_lock(&port->serial->disc_mutex);
+ if (port->serial->disconnected) {
+ mutex_unlock(&port->serial->disc_mutex);
+ return;
}
- set_current_state(TASK_RUNNING);
- remove_wait_queue(&port->tty->write_wait, &wait);
- /* clear out any remaining data in the buffer */
cypress_buf_clear(priv->buf);
- spin_unlock_irqrestore(&priv->lock, flags);
-
- /* wait for characters to drain from device */
- bps = tty_get_baud_rate(port->tty);
- if (bps > 1200)
- timeout = max((HZ*2560)/bps,HZ/10);
- else
- timeout = 2*HZ;
- schedule_timeout_interruptible(timeout);
-
- dbg("%s - stopping urbs", __FUNCTION__);
- usb_kill_urb (port->interrupt_in_urb);
- usb_kill_urb (port->interrupt_out_urb);
-
- if (port->tty) {
- c_cflag = port->tty->termios->c_cflag;
- if (c_cflag & HUPCL) {
- /* drop dtr and rts */
- priv = usb_get_serial_port_data(port);
- spin_lock_irqsave(&priv->lock, flags);
- priv->line_control = 0;
- priv->cmd_ctrl = 1;
- spin_unlock_irqrestore(&priv->lock, flags);
- cypress_write(port, NULL, 0);
- }
- }
+ dbg("%s - stopping urbs", __func__);
+ usb_kill_urb(port->interrupt_in_urb);
+ usb_kill_urb(port->interrupt_out_urb);
+
if (stats)
- dev_info (&port->dev, "Statistics: %d Bytes In | %d Bytes Out | %d Commands Issued\n",
- priv->bytes_in, priv->bytes_out, priv->cmd_count);
+ dev_info(&port->dev, "Statistics: %d Bytes In | %d Bytes Out | %d Commands Issued\n",
+ priv->bytes_in, priv->bytes_out, priv->cmd_count);
+ mutex_unlock(&port->serial->disc_mutex);
} /* cypress_close */
-static int cypress_write(struct usb_serial_port *port, const unsigned char *buf, int count)
+static int cypress_write(struct tty_struct *tty, struct usb_serial_port *port,
+ const unsigned char *buf, int count)
{
struct cypress_private *priv = usb_get_serial_port_data(port);
unsigned long flags;
-
- dbg("%s - port %d, %d bytes", __FUNCTION__, port->number, count);
+
+ dbg("%s - port %d, %d bytes", __func__, port->number, count);
/* line control commands, which need to be executed immediately,
are not put into the buffer for obvious reasons.
count = 0;
goto finish;
}
-
+
if (!count)
return count;
-
+
spin_lock_irqsave(&priv->lock, flags);
count = cypress_buf_put(priv->buf, buf, count);
spin_unlock_irqrestore(&priv->lock, flags);
int count = 0, result, offset, actual_size;
struct cypress_private *priv = usb_get_serial_port_data(port);
unsigned long flags;
-
+
if (!priv->comm_is_ok)
return;
- dbg("%s - port %d", __FUNCTION__, port->number);
- dbg("%s - interrupt out size is %d", __FUNCTION__, port->interrupt_out_size);
-
+ dbg("%s - port %d", __func__, port->number);
+ dbg("%s - interrupt out size is %d", __func__,
+ port->interrupt_out_size);
+
spin_lock_irqsave(&priv->lock, flags);
if (priv->write_urb_in_use) {
- dbg("%s - can't write, urb in use", __FUNCTION__);
+ dbg("%s - can't write, urb in use", __func__);
spin_unlock_irqrestore(&priv->lock, flags);
return;
}
spin_unlock_irqrestore(&priv->lock, flags);
/* clear buffer */
- memset(port->interrupt_out_urb->transfer_buffer, 0, port->interrupt_out_size);
+ memset(port->interrupt_out_urb->transfer_buffer, 0,
+ port->interrupt_out_size);
spin_lock_irqsave(&priv->lock, flags);
- switch (port->interrupt_out_size) {
- case 32:
- /* this is for the CY7C64013... */
- offset = 2;
- port->interrupt_out_buffer[0] = priv->line_control;
- break;
- case 8:
- /* this is for the CY7C63743... */
- offset = 1;
- port->interrupt_out_buffer[0] = priv->line_control;
- break;
- default:
- dbg("%s - wrong packet size", __FUNCTION__);
- spin_unlock_irqrestore(&priv->lock, flags);
- return;
+ switch (priv->pkt_fmt) {
+ default:
+ case packet_format_1:
+ /* this is for the CY7C64013... */
+ offset = 2;
+ port->interrupt_out_buffer[0] = priv->line_control;
+ break;
+ case packet_format_2:
+ /* this is for the CY7C63743... */
+ offset = 1;
+ port->interrupt_out_buffer[0] = priv->line_control;
+ break;
}
if (priv->line_control & CONTROL_RESET)
if (priv->cmd_ctrl) {
priv->cmd_count++;
- dbg("%s - line control command being issued", __FUNCTION__);
+ dbg("%s - line control command being issued", __func__);
spin_unlock_irqrestore(&priv->lock, flags);
goto send;
} else
count = cypress_buf_get(priv->buf, &port->interrupt_out_buffer[offset],
port->interrupt_out_size-offset);
- if (count == 0) {
+ if (count == 0)
return;
- }
- switch (port->interrupt_out_size) {
- case 32:
- port->interrupt_out_buffer[1] = count;
- break;
- case 8:
- port->interrupt_out_buffer[0] |= count;
+ switch (priv->pkt_fmt) {
+ default:
+ case packet_format_1:
+ port->interrupt_out_buffer[1] = count;
+ break;
+ case packet_format_2:
+ port->interrupt_out_buffer[0] |= count;
}
- dbg("%s - count is %d", __FUNCTION__, count);
+ dbg("%s - count is %d", __func__, count);
send:
spin_lock_irqsave(&priv->lock, flags);
if (priv->cmd_ctrl)
actual_size = 1;
else
- actual_size = count + (port->interrupt_out_size == 32 ? 2 : 1);
-
- usb_serial_debug_data(debug, &port->dev, __FUNCTION__, port->interrupt_out_size,
- port->interrupt_out_urb->transfer_buffer);
+ actual_size = count +
+ (priv->pkt_fmt == packet_format_1 ? 2 : 1);
+
+ usb_serial_debug_data(debug, &port->dev, __func__,
+ port->interrupt_out_size,
+ port->interrupt_out_urb->transfer_buffer);
usb_fill_int_urb(port->interrupt_out_urb, port->serial->dev,
usb_sndintpipe(port->serial->dev, port->interrupt_out_endpointAddress),
port->interrupt_out_buffer, port->interrupt_out_size,
cypress_write_int_callback, port, priv->write_urb_interval);
- result = usb_submit_urb (port->interrupt_out_urb, GFP_ATOMIC);
+ result = usb_submit_urb(port->interrupt_out_urb, GFP_ATOMIC);
if (result) {
- dev_err(&port->dev, "%s - failed submitting write urb, error %d\n", __FUNCTION__,
- result);
+ dev_err(&port->dev,
+ "%s - failed submitting write urb, error %d\n",
+ __func__, result);
priv->write_urb_in_use = 0;
cypress_set_dead(port);
}
spin_lock_irqsave(&priv->lock, flags);
- if (priv->cmd_ctrl) {
+ if (priv->cmd_ctrl)
priv->cmd_ctrl = 0;
- }
- priv->bytes_out += count; /* do not count the line control and size bytes */
+
+ /* do not count the line control and size bytes */
+ priv->bytes_out += count;
spin_unlock_irqrestore(&priv->lock, flags);
usb_serial_port_softint(port);
/* returns how much space is available in the soft buffer */
-static int cypress_write_room(struct usb_serial_port *port)
+static int cypress_write_room(struct tty_struct *tty)
{
+ struct usb_serial_port *port = tty->driver_data;
struct cypress_private *priv = usb_get_serial_port_data(port);
int room = 0;
unsigned long flags;
- dbg("%s - port %d", __FUNCTION__, port->number);
+ dbg("%s - port %d", __func__, port->number);
spin_lock_irqsave(&priv->lock, flags);
room = cypress_buf_space_avail(priv->buf);
spin_unlock_irqrestore(&priv->lock, flags);
- dbg("%s - returns %d", __FUNCTION__, room);
+ dbg("%s - returns %d", __func__, room);
return room;
}
-static int cypress_tiocmget (struct usb_serial_port *port, struct file *file)
+static int cypress_tiocmget(struct tty_struct *tty, struct file *file)
{
+ struct usb_serial_port *port = tty->driver_data;
struct cypress_private *priv = usb_get_serial_port_data(port);
__u8 status, control;
unsigned int result = 0;
unsigned long flags;
-
- dbg("%s - port %d", __FUNCTION__, port->number);
+
+ dbg("%s - port %d", __func__, port->number);
spin_lock_irqsave(&priv->lock, flags);
control = priv->line_control;
| ((status & UART_RI) ? TIOCM_RI : 0)
| ((status & UART_CD) ? TIOCM_CD : 0);
- dbg("%s - result = %x", __FUNCTION__, result);
+ dbg("%s - result = %x", __func__, result);
return result;
}
-static int cypress_tiocmset (struct usb_serial_port *port, struct file *file,
+static int cypress_tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear)
{
+ struct usb_serial_port *port = tty->driver_data;
struct cypress_private *priv = usb_get_serial_port_data(port);
unsigned long flags;
-
- dbg("%s - port %d", __FUNCTION__, port->number);
+
+ dbg("%s - port %d", __func__, port->number);
spin_lock_irqsave(&priv->lock, flags);
if (set & TIOCM_RTS)
priv->line_control &= ~CONTROL_RTS;
if (clear & TIOCM_DTR)
priv->line_control &= ~CONTROL_DTR;
+ priv->cmd_ctrl = 1;
spin_unlock_irqrestore(&priv->lock, flags);
- priv->cmd_ctrl = 1;
- return cypress_write(port, NULL, 0);
+ return cypress_write(tty, port, NULL, 0);
}
-static int cypress_ioctl (struct usb_serial_port *port, struct file * file, unsigned int cmd, unsigned long arg)
+static int cypress_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg)
{
+ struct usb_serial_port *port = tty->driver_data;
struct cypress_private *priv = usb_get_serial_port_data(port);
- dbg("%s - port %d, cmd 0x%.4x", __FUNCTION__, port->number, cmd);
+ dbg("%s - port %d, cmd 0x%.4x", __func__, port->number, cmd);
switch (cmd) {
- case TIOCGSERIAL:
- if (copy_to_user((void __user *)arg, port->tty->termios, sizeof(struct ktermios))) {
- return -EFAULT;
- }
- return (0);
- break;
- case TIOCSSERIAL:
- if (copy_from_user(port->tty->termios, (void __user *)arg, sizeof(struct ktermios))) {
- return -EFAULT;
+ /* This code comes from drivers/char/serial.c and ftdi_sio.c */
+ case TIOCMIWAIT:
+ while (priv != NULL) {
+ interruptible_sleep_on(&priv->delta_msr_wait);
+ /* see if a signal did it */
+ if (signal_pending(current))
+ return -ERESTARTSYS;
+ else {
+ char diff = priv->diff_status;
+ if (diff == 0)
+ return -EIO; /* no change => error */
+
+ /* consume all events */
+ priv->diff_status = 0;
+
+ /* return 0 if caller wanted to know about
+ these bits */
+ if (((arg & TIOCM_RNG) && (diff & UART_RI)) ||
+ ((arg & TIOCM_DSR) && (diff & UART_DSR)) ||
+ ((arg & TIOCM_CD) && (diff & UART_CD)) ||
+ ((arg & TIOCM_CTS) && (diff & UART_CTS)))
+ return 0;
+ /* otherwise caller can't care less about what
+ * happened, and so we continue to wait for
+ * more events.
+ */
}
- /* here we need to call cypress_set_termios to invoke the new settings */
- cypress_set_termios(port, &priv->tmp_termios);
- return (0);
- break;
- /* This code comes from drivers/char/serial.c and ftdi_sio.c */
- case TIOCMIWAIT:
- while (priv != NULL) {
- interruptible_sleep_on(&priv->delta_msr_wait);
- /* see if a signal did it */
- if (signal_pending(current))
- return -ERESTARTSYS;
- else {
- char diff = priv->diff_status;
-
- if (diff == 0) {
- return -EIO; /* no change => error */
- }
-
- /* consume all events */
- priv->diff_status = 0;
-
- /* return 0 if caller wanted to know about these bits */
- if ( ((arg & TIOCM_RNG) && (diff & UART_RI)) ||
- ((arg & TIOCM_DSR) && (diff & UART_DSR)) ||
- ((arg & TIOCM_CD) && (diff & UART_CD)) ||
- ((arg & TIOCM_CTS) && (diff & UART_CTS)) ) {
- return 0;
- }
- /* otherwise caller can't care less about what happened,
- * and so we continue to wait for more events.
- */
- }
- }
- return 0;
- break;
- default:
- break;
+ }
+ return 0;
+ default:
+ break;
}
-
- dbg("%s - arg not supported - it was 0x%04x - check include/asm/ioctls.h", __FUNCTION__, cmd);
-
+ dbg("%s - arg not supported - it was 0x%04x - check include/asm/ioctls.h", __func__, cmd);
return -ENOIOCTLCMD;
} /* cypress_ioctl */
-static void cypress_set_termios (struct usb_serial_port *port,
- struct ktermios *old_termios)
+static void cypress_set_termios(struct tty_struct *tty,
+ struct usb_serial_port *port, struct ktermios *old_termios)
{
struct cypress_private *priv = usb_get_serial_port_data(port);
- struct tty_struct *tty;
int data_bits, stop_bits, parity_type, parity_enable;
- unsigned cflag, iflag, baud_mask;
+ unsigned cflag, iflag;
unsigned long flags;
__u8 oldlines;
int linechange = 0;
- dbg("%s - port %d", __FUNCTION__, port->number);
-
- tty = port->tty;
- if ((!tty) || (!tty->termios)) {
- dbg("%s - no tty structures", __FUNCTION__);
- return;
- }
+ dbg("%s - port %d", __func__, port->number);
spin_lock_irqsave(&priv->lock, flags);
+ /* We can't clean this one up as we don't know the device type
+ early enough */
if (!priv->termios_initialized) {
if (priv->chiptype == CT_EARTHMATE) {
*(tty->termios) = tty_std_termios;
tty->termios->c_cflag = B4800 | CS8 | CREAD | HUPCL |
CLOCAL;
+ tty->termios->c_ispeed = 4800;
+ tty->termios->c_ospeed = 4800;
} else if (priv->chiptype == CT_CYPHIDCOM) {
*(tty->termios) = tty_std_termios;
tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL |
CLOCAL;
+ tty->termios->c_ispeed = 9600;
+ tty->termios->c_ospeed = 9600;
} else if (priv->chiptype == CT_CA42V2) {
*(tty->termios) = tty_std_termios;
tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL |
CLOCAL;
+ tty->termios->c_ispeed = 9600;
+ tty->termios->c_ospeed = 9600;
}
priv->termios_initialized = 1;
}
spin_unlock_irqrestore(&priv->lock, flags);
+ /* Unsupported features need clearing */
+ tty->termios->c_cflag &= ~(CMSPAR|CRTSCTS);
+
cflag = tty->termios->c_cflag;
iflag = tty->termios->c_iflag;
/* check if there are new settings */
if (old_termios) {
- if ((cflag != old_termios->c_cflag) ||
- (RELEVANT_IFLAG(iflag) !=
- RELEVANT_IFLAG(old_termios->c_iflag))) {
- dbg("%s - attempting to set new termios settings",
- __FUNCTION__);
- /* should make a copy of this in case something goes
- * wrong in the function, we can restore it */
- spin_lock_irqsave(&priv->lock, flags);
- priv->tmp_termios = *(tty->termios);
- spin_unlock_irqrestore(&priv->lock, flags);
- } else {
- dbg("%s - nothing to do, exiting", __FUNCTION__);
- return;
- }
- } else
- return;
+ spin_lock_irqsave(&priv->lock, flags);
+ priv->tmp_termios = *(tty->termios);
+ spin_unlock_irqrestore(&priv->lock, flags);
+ }
/* set number of data bits, parity, stop bits */
/* when parity is disabled the parity type bit is ignored */
} else
parity_enable = parity_type = 0;
- if (cflag & CSIZE) {
- switch (cflag & CSIZE) {
- case CS5:
- data_bits = 0;
- break;
- case CS6:
- data_bits = 1;
- break;
- case CS7:
- data_bits = 2;
- break;
- case CS8:
- data_bits = 3;
- break;
- default:
- err("%s - CSIZE was set, but not CS5-CS8",
- __FUNCTION__);
- data_bits = 3;
- }
- } else
+ switch (cflag & CSIZE) {
+ case CS5:
+ data_bits = 0;
+ break;
+ case CS6:
+ data_bits = 1;
+ break;
+ case CS7:
+ data_bits = 2;
+ break;
+ case CS8:
data_bits = 3;
-
+ break;
+ default:
+ dev_err(&port->dev, "%s - CSIZE was set, but not CS5-CS8\n",
+ __func__);
+ data_bits = 3;
+ }
spin_lock_irqsave(&priv->lock, flags);
oldlines = priv->line_control;
if ((cflag & CBAUD) == B0) {
/* drop dtr and rts */
- dbg("%s - dropping the lines, baud rate 0bps", __FUNCTION__);
- baud_mask = B0;
+ dbg("%s - dropping the lines, baud rate 0bps", __func__);
priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS);
- } else {
- baud_mask = (cflag & CBAUD);
- switch(baud_mask) {
- case B300:
- dbg("%s - setting baud 300bps", __FUNCTION__);
- break;
- case B600:
- dbg("%s - setting baud 600bps", __FUNCTION__);
- break;
- case B1200:
- dbg("%s - setting baud 1200bps", __FUNCTION__);
- break;
- case B2400:
- dbg("%s - setting baud 2400bps", __FUNCTION__);
- break;
- case B4800:
- dbg("%s - setting baud 4800bps", __FUNCTION__);
- break;
- case B9600:
- dbg("%s - setting baud 9600bps", __FUNCTION__);
- break;
- case B19200:
- dbg("%s - setting baud 19200bps", __FUNCTION__);
- break;
- case B38400:
- dbg("%s - setting baud 38400bps", __FUNCTION__);
- break;
- case B57600:
- dbg("%s - setting baud 57600bps", __FUNCTION__);
- break;
- case B115200:
- dbg("%s - setting baud 115200bps", __FUNCTION__);
- break;
- default:
- dbg("%s - unknown masked baud rate", __FUNCTION__);
- }
+ } else
priv->line_control = (CONTROL_DTR | CONTROL_RTS);
- }
spin_unlock_irqrestore(&priv->lock, flags);
dbg("%s - sending %d stop_bits, %d parity_enable, %d parity_type, "
- "%d data_bits (+5)", __FUNCTION__, stop_bits,
+ "%d data_bits (+5)", __func__, stop_bits,
parity_enable, parity_type, data_bits);
- cypress_serial_control(port, baud_mask, data_bits, stop_bits,
- parity_enable, parity_type, 0, CYPRESS_SET_CONFIG);
+ cypress_serial_control(tty, port, tty_get_baud_rate(tty),
+ data_bits, stop_bits,
+ parity_enable, parity_type,
+ 0, CYPRESS_SET_CONFIG);
/* we perform a CYPRESS_GET_CONFIG so that the current settings are
* filled into the private structure this should confirm that all is
* working if it returns what we just set */
- cypress_serial_control(port, 0, 0, 0, 0, 0, 0, CYPRESS_GET_CONFIG);
+ cypress_serial_control(tty, port, 0, 0, 0, 0, 0, 0, CYPRESS_GET_CONFIG);
/* Here we can define custom tty settings for devices; the main tty
* termios flag base comes from empeg.c */
spin_lock_irqsave(&priv->lock, flags);
- if ( (priv->chiptype == CT_EARTHMATE) && (priv->baud_rate == 4800) ) {
+ if (priv->chiptype == CT_EARTHMATE && priv->baud_rate == 4800) {
dbg("Using custom termios settings for a baud rate of "
"4800bps.");
/* define custom termios settings for NMEA protocol */
/* if necessary, set lines */
if (linechange) {
priv->cmd_ctrl = 1;
- cypress_write(port, NULL, 0);
+ cypress_write(tty, port, NULL, 0);
}
} /* cypress_set_termios */
/* returns amount of data still left in soft buffer */
-static int cypress_chars_in_buffer(struct usb_serial_port *port)
+static int cypress_chars_in_buffer(struct tty_struct *tty)
{
+ struct usb_serial_port *port = tty->driver_data;
struct cypress_private *priv = usb_get_serial_port_data(port);
int chars = 0;
unsigned long flags;
- dbg("%s - port %d", __FUNCTION__, port->number);
-
+ dbg("%s - port %d", __func__, port->number);
+
spin_lock_irqsave(&priv->lock, flags);
chars = cypress_buf_data_avail(priv->buf);
spin_unlock_irqrestore(&priv->lock, flags);
- dbg("%s - returns %d", __FUNCTION__, chars);
+ dbg("%s - returns %d", __func__, chars);
return chars;
}
-static void cypress_throttle (struct usb_serial_port *port)
+static void cypress_throttle(struct tty_struct *tty)
{
+ struct usb_serial_port *port = tty->driver_data;
struct cypress_private *priv = usb_get_serial_port_data(port);
- unsigned long flags;
- dbg("%s - port %d", __FUNCTION__, port->number);
+ dbg("%s - port %d", __func__, port->number);
- spin_lock_irqsave(&priv->lock, flags);
+ spin_lock_irq(&priv->lock);
priv->rx_flags = THROTTLED;
- spin_unlock_irqrestore(&priv->lock, flags);
+ spin_unlock_irq(&priv->lock);
}
-static void cypress_unthrottle (struct usb_serial_port *port)
+static void cypress_unthrottle(struct tty_struct *tty)
{
+ struct usb_serial_port *port = tty->driver_data;
struct cypress_private *priv = usb_get_serial_port_data(port);
int actually_throttled, result;
- unsigned long flags;
- dbg("%s - port %d", __FUNCTION__, port->number);
+ dbg("%s - port %d", __func__, port->number);
- spin_lock_irqsave(&priv->lock, flags);
+ spin_lock_irq(&priv->lock);
actually_throttled = priv->rx_flags & ACTUALLY_THROTTLED;
priv->rx_flags = 0;
- spin_unlock_irqrestore(&priv->lock, flags);
+ spin_unlock_irq(&priv->lock);
if (!priv->comm_is_ok)
return;
if (actually_throttled) {
port->interrupt_in_urb->dev = port->serial->dev;
- result = usb_submit_urb(port->interrupt_in_urb, GFP_ATOMIC);
+ result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
if (result) {
dev_err(&port->dev, "%s - failed submitting read urb, "
- "error %d\n", __FUNCTION__, result);
+ "error %d\n", __func__, result);
cypress_set_dead(port);
}
}
static void cypress_read_int_callback(struct urb *urb)
{
- struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
+ struct usb_serial_port *port = urb->context;
struct cypress_private *priv = usb_get_serial_port_data(port);
struct tty_struct *tty;
unsigned char *data = urb->transfer_buffer;
int bytes = 0;
int result;
int i = 0;
+ int status = urb->status;
- dbg("%s - port %d", __FUNCTION__, port->number);
+ dbg("%s - port %d", __func__, port->number);
- switch (urb->status) {
+ switch (status) {
case 0: /* success */
break;
case -ECONNRESET:
/* precursor to disconnect so just go away */
return;
case -EPIPE:
- usb_clear_halt(port->serial->dev,0x81);
- break;
+ /* Can't call usb_clear_halt while in_interrupt */
+ /* FALLS THROUGH */
default:
/* something ugly is going on... */
- dev_err(&urb->dev->dev,"%s - unexpected nonzero read status received: %d\n",
- __FUNCTION__,urb->status);
+ dev_err(&urb->dev->dev,
+ "%s - unexpected nonzero read status received: %d\n",
+ __func__, status);
cypress_set_dead(port);
return;
}
spin_lock_irqsave(&priv->lock, flags);
if (priv->rx_flags & THROTTLED) {
- dbg("%s - now throttling", __FUNCTION__);
+ dbg("%s - now throttling", __func__);
priv->rx_flags |= ACTUALLY_THROTTLED;
spin_unlock_irqrestore(&priv->lock, flags);
return;
}
spin_unlock_irqrestore(&priv->lock, flags);
- tty = port->tty;
+ tty = tty_port_tty_get(&port->port);
if (!tty) {
- dbg("%s - bad tty pointer - exiting", __FUNCTION__);
+ dbg("%s - bad tty pointer - exiting", __func__);
return;
}
spin_lock_irqsave(&priv->lock, flags);
- switch(urb->actual_length) {
- case 32:
- /* This is for the CY7C64013... */
- priv->current_status = data[0] & 0xF8;
- bytes = data[1] + 2;
- i = 2;
- if (bytes > 2)
- havedata = 1;
- break;
- case 8:
- /* This is for the CY7C63743... */
- priv->current_status = data[0] & 0xF8;
- bytes = (data[0] & 0x07) + 1;
- i = 1;
- if (bytes > 1)
- havedata = 1;
- break;
- default:
- dbg("%s - wrong packet size - received %d bytes",
- __FUNCTION__, urb->actual_length);
- spin_unlock_irqrestore(&priv->lock, flags);
- goto continue_read;
+ result = urb->actual_length;
+ switch (priv->pkt_fmt) {
+ default:
+ case packet_format_1:
+ /* This is for the CY7C64013... */
+ priv->current_status = data[0] & 0xF8;
+ bytes = data[1] + 2;
+ i = 2;
+ if (bytes > 2)
+ havedata = 1;
+ break;
+ case packet_format_2:
+ /* This is for the CY7C63743... */
+ priv->current_status = data[0] & 0xF8;
+ bytes = (data[0] & 0x07) + 1;
+ i = 1;
+ if (bytes > 1)
+ havedata = 1;
+ break;
}
spin_unlock_irqrestore(&priv->lock, flags);
+ if (result < bytes) {
+ dbg("%s - wrong packet size - received %d bytes but packet "
+ "said %d bytes", __func__, result, bytes);
+ goto continue_read;
+ }
- usb_serial_debug_data (debug, &port->dev, __FUNCTION__,
- urb->actual_length, data);
+ usb_serial_debug_data(debug, &port->dev, __func__,
+ urb->actual_length, data);
spin_lock_irqsave(&priv->lock, flags);
/* check to see if status has changed */
- if (priv != NULL) {
- if (priv->current_status != priv->prev_status) {
- priv->diff_status |= priv->current_status ^
- priv->prev_status;
- wake_up_interruptible(&priv->delta_msr_wait);
- priv->prev_status = priv->current_status;
- }
+ if (priv->current_status != priv->prev_status) {
+ priv->diff_status |= priv->current_status ^
+ priv->prev_status;
+ wake_up_interruptible(&priv->delta_msr_wait);
+ priv->prev_status = priv->current_status;
}
spin_unlock_irqrestore(&priv->lock, flags);
* though */
if (tty && !(tty->termios->c_cflag & CLOCAL) &&
!(priv->current_status & UART_CD)) {
- dbg("%s - calling hangup", __FUNCTION__);
+ dbg("%s - calling hangup", __func__);
tty_hangup(tty);
goto continue_read;
}
if (priv->current_status & CYP_ERROR) {
spin_unlock_irqrestore(&priv->lock, flags);
tty_flag = TTY_PARITY;
- dbg("%s - Parity Error detected", __FUNCTION__);
+ dbg("%s - Parity Error detected", __func__);
} else
spin_unlock_irqrestore(&priv->lock, flags);
/* process read if there is data other than line status */
- if (tty && (bytes > i)) {
- bytes = tty_buffer_request_room(tty, bytes);
- for (; i < bytes ; ++i) {
- dbg("pushing byte number %d - %d - %c", i, data[i],
- data[i]);
- tty_insert_flip_char(tty, data[i], tty_flag);
- }
- tty_flip_buffer_push(port->tty);
+ if (tty && bytes > i) {
+ tty_insert_flip_string_fixed_flag(tty, data + i,
+ bytes - i, tty_flag);
+ tty_flip_buffer_push(tty);
}
spin_lock_irqsave(&priv->lock, flags);
spin_unlock_irqrestore(&priv->lock, flags);
continue_read:
+ tty_kref_put(tty);
- /* Continue trying to always read... unless the port has closed. */
+ /* Continue trying to always read */
- if (port->open_count > 0 && priv->comm_is_ok) {
+ if (priv->comm_is_ok) {
usb_fill_int_urb(port->interrupt_in_urb, port->serial->dev,
usb_rcvintpipe(port->serial->dev,
port->interrupt_in_endpointAddress),
port->interrupt_in_urb->transfer_buffer,
port->interrupt_in_urb->transfer_buffer_length,
- cypress_read_int_callback, port, priv->read_urb_interval);
+ cypress_read_int_callback, port,
+ priv->read_urb_interval);
result = usb_submit_urb(port->interrupt_in_urb, GFP_ATOMIC);
- if (result) {
+ if (result && result != -EPERM) {
dev_err(&urb->dev->dev, "%s - failed resubmitting "
- "read urb, error %d\n", __FUNCTION__,
+ "read urb, error %d\n", __func__,
result);
cypress_set_dead(port);
}
static void cypress_write_int_callback(struct urb *urb)
{
- struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
+ struct usb_serial_port *port = urb->context;
struct cypress_private *priv = usb_get_serial_port_data(port);
int result;
+ int status = urb->status;
+
+ dbg("%s - port %d", __func__, port->number);
- dbg("%s - port %d", __FUNCTION__, port->number);
-
- switch (urb->status) {
- case 0:
- /* success */
+ switch (status) {
+ case 0:
+ /* success */
+ break;
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ /* this urb is terminated, clean up */
+ dbg("%s - urb shutting down with status: %d",
+ __func__, status);
+ priv->write_urb_in_use = 0;
+ return;
+ case -EPIPE: /* no break needed; clear halt and resubmit */
+ if (!priv->comm_is_ok)
break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* this urb is terminated, clean up */
- dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status);
- priv->write_urb_in_use = 0;
+ usb_clear_halt(port->serial->dev, 0x02);
+ /* error in the urb, so we have to resubmit it */
+ dbg("%s - nonzero write bulk status received: %d",
+ __func__, status);
+ port->interrupt_out_urb->transfer_buffer_length = 1;
+ port->interrupt_out_urb->dev = port->serial->dev;
+ result = usb_submit_urb(port->interrupt_out_urb, GFP_ATOMIC);
+ if (!result)
return;
- case -EPIPE: /* no break needed; clear halt and resubmit */
- if (!priv->comm_is_ok)
- break;
- usb_clear_halt(port->serial->dev, 0x02);
- /* error in the urb, so we have to resubmit it */
- dbg("%s - nonzero write bulk status received: %d", __FUNCTION__, urb->status);
- port->interrupt_out_urb->transfer_buffer_length = 1;
- port->interrupt_out_urb->dev = port->serial->dev;
- result = usb_submit_urb(port->interrupt_out_urb, GFP_ATOMIC);
- if (!result)
- return;
- dev_err(&urb->dev->dev, "%s - failed resubmitting write urb, error %d\n",
- __FUNCTION__, result);
- cypress_set_dead(port);
- break;
- default:
- dev_err(&urb->dev->dev,"%s - unexpected nonzero write status received: %d\n",
- __FUNCTION__,urb->status);
- cypress_set_dead(port);
- break;
+ dev_err(&urb->dev->dev,
+ "%s - failed resubmitting write urb, error %d\n",
+ __func__, result);
+ cypress_set_dead(port);
+ break;
+ default:
+ dev_err(&urb->dev->dev,
+ "%s - unexpected nonzero write status received: %d\n",
+ __func__, status);
+ cypress_set_dead(port);
+ break;
}
-
priv->write_urb_in_use = 0;
-
+
/* send any buffered data */
cypress_send(port);
}
static unsigned int cypress_buf_data_avail(struct cypress_buf *cb)
{
if (cb != NULL)
- return ((cb->buf_size + cb->buf_put - cb->buf_get) % cb->buf_size);
+ return (cb->buf_size + cb->buf_put - cb->buf_get)
+ % cb->buf_size;
else
return 0;
}
static unsigned int cypress_buf_space_avail(struct cypress_buf *cb)
{
if (cb != NULL)
- return ((cb->buf_size + cb->buf_get - cb->buf_put - 1) % cb->buf_size);
+ return (cb->buf_size + cb->buf_get - cb->buf_put - 1)
+ % cb->buf_size;
else
return 0;
}
static int __init cypress_init(void)
{
int retval;
-
- dbg("%s", __FUNCTION__);
-
+
+ dbg("%s", __func__);
+
retval = usb_serial_register(&cypress_earthmate_device);
if (retval)
goto failed_em_register;
if (retval)
goto failed_usb_register;
- info(DRIVER_DESC " " DRIVER_VERSION);
+ printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
+ DRIVER_DESC "\n");
return 0;
failed_usb_register:
}
-static void __exit cypress_exit (void)
+static void __exit cypress_exit(void)
{
- dbg("%s", __FUNCTION__);
+ dbg("%s", __func__);
- usb_deregister (&cypress_driver);
- usb_serial_deregister (&cypress_earthmate_device);
- usb_serial_deregister (&cypress_hidcom_device);
- usb_serial_deregister (&cypress_ca42v2_device);
+ usb_deregister(&cypress_driver);
+ usb_serial_deregister(&cypress_earthmate_device);
+ usb_serial_deregister(&cypress_hidcom_device);
+ usb_serial_deregister(&cypress_ca42v2_device);
}
module_init(cypress_init);
module_exit(cypress_exit);
-MODULE_AUTHOR( DRIVER_AUTHOR );
-MODULE_DESCRIPTION( DRIVER_DESC );
-MODULE_VERSION( DRIVER_VERSION );
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_VERSION(DRIVER_VERSION);
MODULE_LICENSE("GPL");
module_param(debug, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(stats, "Enable statistics or not");
module_param(interval, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(interval, "Overrides interrupt interval");
+module_param(unstable_bauds, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(unstable_bauds, "Allow unstable baud rates");
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff