#include <linux/spinlock.h>
#include "r8180_hw.h"
#include "r8180.h"
-#include "r8180_sa2400.h" /* PHILIPS Radio frontend */
-#include "r8180_max2820.h" /* MAXIM Radio frontend */
-#include "r8180_gct.h" /* GCT Radio frontend */
#include "r8180_rtl8225.h" /* RTL8225 Radio frontend */
-#include "r8180_rtl8255.h" /* RTL8255 Radio frontend */
#include "r8180_93cx6.h" /* Card EEPROM */
#include "r8180_wx.h"
-#include "r8180_pm.h"
-
#include "ieee80211/dot11d.h"
-#ifdef CONFIG_RTL8185B
//#define CONFIG_RTL8180_IO_MAP
u8 data
)
{
-#ifndef CONFIG_RTL8180_IO_MAP
write_nic_byte(dev, offset, data);
read_nic_byte(dev, offset); // To make sure write operation is completed, 2005.11.09, by rcnjko.
-#else // Port IO
- u32 Page = (offset >> 8);
-
- switch(Page)
- {
- case 0: // Page 0
- write_nic_byte(dev, offset, data);
- break;
-
- case 1: // Page 1
- case 2: // Page 2
- case 3: // Page 3
- {
- u8 psr = read_nic_byte(dev, PSR);
-
- write_nic_byte(dev, PSR, ((psr & 0xfc) | (u8)Page)); // Switch to page N.
- write_nic_byte(dev, (offset & 0xff), data);
- write_nic_byte(dev, PSR, (psr & 0xfc)); // Switch to page 0.
- }
- break;
-
- default:
- // Illegal page number.
- DMESGE("PlatformIOWrite1Byte(): illegal page number: %d, offset: %#X", Page, offset);
- break;
- }
-#endif
}
void
u16 data
)
{
-#ifndef CONFIG_RTL8180_IO_MAP
write_nic_word(dev, offset, data);
read_nic_word(dev, offset); // To make sure write operation is completed, 2005.11.09, by rcnjko.
-#else // Port IO
- u32 Page = (offset >> 8);
-
- switch(Page)
- {
- case 0: // Page 0
- write_nic_word(dev, offset, data);
- break;
-
- case 1: // Page 1
- case 2: // Page 2
- case 3: // Page 3
- {
- u8 psr = read_nic_byte(dev, PSR);
-
- write_nic_byte(dev, PSR, ((psr & 0xfc) | (u8)Page)); // Switch to page N.
- write_nic_word(dev, (offset & 0xff), data);
- write_nic_byte(dev, PSR, (psr & 0xfc)); // Switch to page 0.
- }
- break;
-
- default:
- // Illegal page number.
- DMESGE("PlatformIOWrite2Byte(): illegal page number: %d, offset: %#X", Page, offset);
- break;
- }
-#endif
}
u8 PlatformIORead1Byte(struct net_device *dev, u32 offset);
u32 data
)
{
-#ifndef CONFIG_RTL8180_IO_MAP
//{by amy 080312
if (offset == PhyAddr)
{//For Base Band configuration.
write_nic_dword(dev, offset, data);
read_nic_dword(dev, offset); // To make sure write operation is completed, 2005.11.09, by rcnjko.
}
-#else // Port IO
- u32 Page = (offset >> 8);
-
- switch(Page)
- {
- case 0: // Page 0
- write_nic_word(dev, offset, data);
- break;
-
- case 1: // Page 1
- case 2: // Page 2
- case 3: // Page 3
- {
- u8 psr = read_nic_byte(dev, PSR);
-
- write_nic_byte(dev, PSR, ((psr & 0xfc) | (u8)Page)); // Switch to page N.
- write_nic_dword(dev, (offset & 0xff), data);
- write_nic_byte(dev, PSR, (psr & 0xfc)); // Switch to page 0.
- }
- break;
-
- default:
- // Illegal page number.
- DMESGE("PlatformIOWrite4Byte(): illegal page number: %d, offset: %#X", Page, offset);
- break;
- }
-#endif
}
u8
{
u8 data = 0;
-#ifndef CONFIG_RTL8180_IO_MAP
data = read_nic_byte(dev, offset);
-#else // Port IO
- u32 Page = (offset >> 8);
-
- switch(Page)
- {
- case 0: // Page 0
- data = read_nic_byte(dev, offset);
- break;
-
- case 1: // Page 1
- case 2: // Page 2
- case 3: // Page 3
- {
- u8 psr = read_nic_byte(dev, PSR);
-
- write_nic_byte(dev, PSR, ((psr & 0xfc) | (u8)Page)); // Switch to page N.
- data = read_nic_byte(dev, (offset & 0xff));
- write_nic_byte(dev, PSR, (psr & 0xfc)); // Switch to page 0.
- }
- break;
-
- default:
- // Illegal page number.
- DMESGE("PlatformIORead1Byte(): illegal page number: %d, offset: %#X", Page, offset);
- break;
- }
-#endif
return data;
}
{
u16 data = 0;
-#ifndef CONFIG_RTL8180_IO_MAP
data = read_nic_word(dev, offset);
-#else // Port IO
- u32 Page = (offset >> 8);
-
- switch(Page)
- {
- case 0: // Page 0
- data = read_nic_word(dev, offset);
- break;
-
- case 1: // Page 1
- case 2: // Page 2
- case 3: // Page 3
- {
- u8 psr = read_nic_byte(dev, PSR);
-
- write_nic_byte(dev, PSR, ((psr & 0xfc) | (u8)Page)); // Switch to page N.
- data = read_nic_word(dev, (offset & 0xff));
- write_nic_byte(dev, PSR, (psr & 0xfc)); // Switch to page 0.
- }
- break;
-
- default:
- // Illegal page number.
- DMESGE("PlatformIORead2Byte(): illegal page number: %d, offset: %#X", Page, offset);
- break;
- }
-#endif
return data;
}
{
u32 data = 0;
-#ifndef CONFIG_RTL8180_IO_MAP
data = read_nic_dword(dev, offset);
-#else // Port IO
- u32 Page = (offset >> 8);
-
- switch(Page)
- {
- case 0: // Page 0
- data = read_nic_dword(dev, offset);
- break;
-
- case 1: // Page 1
- case 2: // Page 2
- case 3: // Page 3
- {
- u8 psr = read_nic_byte(dev, PSR);
-
- write_nic_byte(dev, PSR, ((psr & 0xfc) | (u8)Page)); // Switch to page N.
- data = read_nic_dword(dev, (offset & 0xff));
- write_nic_byte(dev, PSR, (psr & 0xfc)); // Switch to page 0.
- }
- break;
-
- default:
- // Illegal page number.
- DMESGE("PlatformIORead4Byte(): illegal page number: %d, offset: %#X\n", Page, offset);
- break;
- }
-#endif
return data;
}
RF_WriteReg(dev, 0x05, 0x05ab); mdelay(1); // Rx mode//+edward
RF_WriteReg(dev, 0x00, 0x009f); mdelay(1); // Rx mode//+edward
-#if 0//-edward
- RF_WriteReg(dev, 0x00, 0x0197); mdelay(1);
- RF_WriteReg(dev, 0x05, 0x05ab); mdelay(1);
- RF_WriteReg(dev, 0x00, 0x009F); mdelay(1);
-#endif
RF_WriteReg(dev, 0x01, 0x0000); mdelay(1); // Rx mode//+edward
RF_WriteReg(dev, 0x02, 0x0000); mdelay(1); // Rx mode//+edward
//power save parameters.
CCK reg0x06[3]=1'b1: turn off unused circuits before cca = 1
CCK reg0x06[2]=1'b1: turn off cck's circuit if macrst =0
*/
-#if 0
- write_nic_dword(dev, PHY_ADR, 0x0100c880);
- write_nic_dword(dev, PHY_ADR, 0x01001c86);
- write_nic_dword(dev, PHY_ADR, 0x01007890);
- write_nic_dword(dev, PHY_ADR, 0x0100d0ae);
- write_nic_dword(dev, PHY_ADR, 0x010006af);
- write_nic_dword(dev, PHY_ADR, 0x01004681);
-#endif
+
write_phy_cck(dev,0x00,0xc8);
write_phy_cck(dev,0x06,0x1c);
write_phy_cck(dev,0x10,0x78);
// Config Sw/Hw Combinational Antenna Diversity. Added by Roger, 2008.02.26.
SetAntennaConfig87SE(dev, priv->bDefaultAntenna1, priv->bSwAntennaDiverity);
//by amy 080312}
-#if 0
- // Config Sw/Hw Antenna Diversity
- if( priv->bSwAntennaDiverity ) // Use SW+Hw Antenna Diversity
- {
- if( priv->bDefaultAntenna1 == true ) // aux antenna
- {
- // Mac register, aux antenna
- write_nic_byte(dev, ANTSEL, 0x00);
- // Config CCK RX antenna.
- write_phy_cck(dev, 0x11, 0xbb); // Reg11 : bb
- write_phy_cck(dev, 0x0c, 0x09); // Reg0c : 09
- write_phy_cck(dev, 0x01, 0xc7); // Reg01 : c7
- // Config OFDM RX antenna.
- write_phy_ofdm(dev, 0x0d, 0x54); // Reg0d : 54
- write_phy_ofdm(dev, 0x18, 0xb2); // Reg18 : b2
- }
- else // main antenna
- {
- // Mac register, main antenna
- write_nic_byte(dev, ANTSEL, 0x03);
- //base band
- // Config CCK RX antenna.
- write_phy_cck(dev, 0x11, 0x9b); // Reg11 : 9b
- write_phy_cck(dev, 0x0c, 0x09); // Reg0c : 09
- write_phy_cck(dev, 0x01, 0xc7); // Reg01 : c7
- // Config OFDM RX antenna.
- write_phy_ofdm(dev, 0x0d, 0x5c); // Reg0d : 5c
- write_phy_ofdm(dev, 0x18, 0xb2); // Reg18 : b2
- }
- }
- else // Disable Antenna Diversity
- {
- if( priv->bDefaultAntenna1 == true ) // aux Antenna
- {
- // Mac register, aux antenna
- write_nic_byte(dev, ANTSEL, 0x00);
- // Config CCK RX antenna.
- write_phy_cck(dev, 0x11, 0xbb); // Reg11 : bb
- write_phy_cck(dev, 0x0c, 0x09); // Reg0c : 09
- write_phy_cck(dev, 0x01, 0x47); // Reg01 : 47
- // Config OFDM RX antenna.
- write_phy_ofdm(dev, 0x0d, 0x54); // Reg0d : 54
- write_phy_ofdm(dev, 0x18, 0x32); // Reg18 : 32
- }
- else // main Antenna
- {
- // Mac register, main antenna
- write_nic_byte(dev, ANTSEL, 0x03);
- // Config CCK RX antenna.
- write_phy_cck(dev, 0x11, 0x9b); // Reg11 : 9b
- write_phy_cck(dev, 0x0c, 0x09); // Reg0c : 09
- write_phy_cck(dev, 0x01, 0x47); // Reg01 : 47
- // Config OFDM RX antenna.
- write_phy_ofdm(dev, 0x0d, 0x5c); // Reg0d : 5c
- write_phy_ofdm(dev, 0x18, 0x32); // Reg18 : 32
- }
- }
-#endif
//by amy for antenna
}
switch(priv->rf_chip)
{
-#if 0
- case RF_ZEBRA2:
- // Dynamic set initial gain, by shien chang, 2006.07.14
- switch(priv->InitialGain)
- {
- case 1: //m861dBm
- DMESG("RTL8185B + 8225 Initial Gain State 1: -82 dBm \n");
- write_nic_dword(dev, PhyAddr, 0x2697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0x86a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfa85); mdelay(1);
- break;
-
- case 2: //m862dBm
- DMESG("RTL8185B + 8225 Initial Gain State 2: -82 dBm \n");
- write_nic_dword(dev, PhyAddr, 0x2697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0x86a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfb85); mdelay(1);
- break;
-
- case 3: //m863dBm
- DMESG("RTL8185B + 8225 Initial Gain State 3: -82 dBm \n");
- write_nic_dword(dev, PhyAddr, 0x2697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0x96a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfb85); mdelay(1);
- break;
-
- case 4: //m864dBm
- DMESG("RTL8185B + 8225 Initial Gain State 4: -78 dBm \n");
- write_nic_dword(dev, PhyAddr, 0x2697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xa6a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfb85); mdelay(1);
- break;
-
- case 5: //m82dBm
- DMESG("RTL8185B + 8225 Initial Gain State 5: -74 dBm \n");
- write_nic_dword(dev, PhyAddr, 0x3697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xa6a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfb85); mdelay(1);
- break;
-
- case 6: //m78dBm
- DMESG("RTL8185B + 8225 Initial Gain State 6: -70 dBm \n");
- write_nic_dword(dev, PhyAddr, 0x4697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xa6a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfb85); mdelay(1);
- break;
-
- case 7: //m74dBm
- DMESG("RTL8185B + 8225 Initial Gain State 7: -66 dBm \n");
- write_nic_dword(dev, PhyAddr, 0x5697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xa6a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfb85); mdelay(1);
- break;
-
- default: //MP
- DMESG("RTL8185B + 8225 Initial Gain State 1: -82 dBm (default)\n");
- write_nic_dword(dev, PhyAddr, 0x2697); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0x86a4); mdelay(1);
- write_nic_dword(dev, PhyAddr, 0xfa85); mdelay(1);
- break;
- }
- break;
-#endif
case RF_ZEBRA4:
// Dynamic set initial gain, follow 87B
switch(priv->InitialGain)
// <RJ_TODO_8185B> We shall set up the ARFR according to user's setting.
//write_nic_word(dev, ARFR, 0x0fff); // set 1M ~ 54M
//by amy
-#if 0
- PlatformIOWrite2Byte(dev, ARFR, 0x0fff); // set 1M ~ 54M
-#endif
// Aadded by Roger, 2007.11.15.
PlatformIOWrite2Byte(dev, ARFR, 0x0fff); //set 1M ~ 54Mbps.
//by amy
// Asked for by SD3 CM Lin, 2006.06.27, by rcnjko.
//PlatformIOWrite4Byte(dev, RFTiming, 0x00004001);
//by amy
-#if 0
- write_nic_dword(dev, RFTiming, 0x00004001);
-#endif
// power save parameter based on "87SE power save parameters 20071127.doc", as follow.
//Enable DA10 TX power saving
notify_wx_assoc_event(priv->ieee80211);
// Stop SW Beacon.Use hw beacon so do not need to do so.by amy
-#if 0
- if(pMgntInfo->bEnableSwBeaconTimer)
- {
- // SwBeaconTimer will stop if pMgntInfo->mIbss==FALSE, see SwBeaconCallback() for details.
-// comment out by haich, 2007.10.01
-//#if DEV_BUS_TYPE==USB_INTERFACE
- PlatformCancelTimer( Adapter, &pMgntInfo->SwBeaconTimer);
-//#endif
- }
-#endif
// MgntIndicateMediaStatus( Adapter, RT_MEDIA_DISCONNECT, GENERAL_INDICATE );
//
// To solve CAM values miss in RF OFF, rewrite CAM values after RF ON. By Bruce, 2007-09-20.
//
-#if 0
- while( index < 4 )
- {
- if( ( pMgntInfo->SecurityInfo.PairwiseEncAlgorithm == WEP104_Encryption ) ||
- (pMgntInfo->SecurityInfo.PairwiseEncAlgorithm == WEP40_Encryption) )
- {
- if( pMgntInfo->SecurityInfo.KeyLen[index] != 0)
- pAdapter->HalFunc.SetKeyHandler(pAdapter, index, 0, FALSE, pMgntInfo->SecurityInfo.PairwiseEncAlgorithm, TRUE, FALSE);
- }
- index++;
- }
-#endif
priv->bSwRfProcessing = false;
}
PhyConfig8185(dev);
// We assume RegWirelessMode has already been initialized before,
- // however, we has to validate the wireless mode here and provide a reasonble
- // initialized value if necessary. 2005.01.13, by rcnjko.
+ // however, we has to validate the wireless mode here and provide a
+ // reasonable initialized value if necessary. 2005.01.13, by rcnjko.
SupportedWirelessMode = GetSupportedWirelessMode8185(dev);
if( (ieee->mode != WIRELESS_MODE_B) &&
(ieee->mode != WIRELESS_MODE_G) &&
InitWirelessMode = ieee->mode;
}
//by amy for power save
-#ifdef ENABLE_IPS
// printk("initialize ENABLE_IPS\n");
priv->eRFPowerState = eRfOff;
priv->RfOffReason = 0;
// printk("rf off cost jiffies:%lx\n", (tmp2-tmp)*1000/HZ);
}
-#endif
// IPSEnter(dev);
//by amy for power save
#ifdef TODO
//u32 rxconf;
/* for now we accept data, management & ctl frame*/
struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
-#if 0
- rxconf=read_nic_dword(dev,RX_CONF);
- rxconf = rxconf &~ MAC_FILTER_MASK;
- rxconf = rxconf | (1<<ACCEPT_MNG_FRAME_SHIFT);
- rxconf = rxconf | (1<<ACCEPT_DATA_FRAME_SHIFT);
- rxconf = rxconf | (1<<ACCEPT_BCAST_FRAME_SHIFT);
- rxconf = rxconf | (1<<ACCEPT_MCAST_FRAME_SHIFT);
-// rxconf = rxconf | (1<<ACCEPT_CRCERR_FRAME_SHIFT);
- if (dev->flags & IFF_PROMISC) DMESG ("NIC in promisc mode");
-
- if(priv->ieee80211->iw_mode == IW_MODE_MONITOR || \
- dev->flags & IFF_PROMISC){
- rxconf = rxconf | (1<<ACCEPT_ALLMAC_FRAME_SHIFT);
- }else{
- rxconf = rxconf | (1<<ACCEPT_NICMAC_FRAME_SHIFT);
- if(priv->card_8185 == 0)
- rxconf = rxconf | (1<<RX_CHECK_BSSID_SHIFT);
- }
-
- /*if(priv->ieee80211->iw_mode == IW_MODE_MASTER){
- rxconf = rxconf | (1<<ACCEPT_ALLMAC_FRAME_SHIFT);
- rxconf = rxconf | (1<<RX_CHECK_BSSID_SHIFT);
- }*/
-
- if(priv->ieee80211->iw_mode == IW_MODE_MONITOR){
- rxconf = rxconf | (1<<ACCEPT_CTL_FRAME_SHIFT);
- rxconf = rxconf | (1<<ACCEPT_ICVERR_FRAME_SHIFT);
- rxconf = rxconf | (1<<ACCEPT_PWR_FRAME_SHIFT);
- }
-
- if( priv->crcmon == 1 && priv->ieee80211->iw_mode == IW_MODE_MONITOR)
- rxconf = rxconf | (1<<ACCEPT_CRCERR_FRAME_SHIFT);
-
- //if(!priv->card_8185){
- rxconf = rxconf &~ RX_FIFO_THRESHOLD_MASK;
- rxconf = rxconf | (RX_FIFO_THRESHOLD_NONE<<RX_FIFO_THRESHOLD_SHIFT);
- //}
-
- rxconf = rxconf | (1<<RX_AUTORESETPHY_SHIFT);
- rxconf = rxconf &~ MAX_RX_DMA_MASK;
- rxconf = rxconf | (MAX_RX_DMA_2048<<MAX_RX_DMA_SHIFT);
-
- //if(!priv->card_8185)
- rxconf = rxconf | RCR_ONLYERLPKT;
-
- rxconf = rxconf &~ RCR_CS_MASK;
- if(!priv->card_8185)
- rxconf |= (priv->rcr_csense<<RCR_CS_SHIFT);
-// rxconf &=~ 0xfff00000;
-// rxconf |= 0x90100000;//9014f76f;
- write_nic_dword(dev, RX_CONF, rxconf);
-#endif
if (dev->flags & IFF_PROMISC) DMESG ("NIC in promisc mode");
//u32 txconf;
struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
-#if 0
- txconf= read_nic_dword(dev,TX_CONF);
- if(priv->card_8185){
-
-
- byte = read_nic_byte(dev,CW_CONF);
- byte &= ~(1<<CW_CONF_PERPACKET_CW_SHIFT);
- byte &= ~(1<<CW_CONF_PERPACKET_RETRY_SHIFT);
- write_nic_byte(dev, CW_CONF, byte);
-
- tx_agc_ctl = read_nic_byte(dev, TX_AGC_CTL);
- tx_agc_ctl &= ~(1<<TX_AGC_CTL_PERPACKET_GAIN_SHIFT);
- tx_agc_ctl &= ~(1<<TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT);
- tx_agc_ctl |=(1<<TX_AGC_CTL_FEEDBACK_ANT);
- write_nic_byte(dev, TX_AGC_CTL, tx_agc_ctl);
- /*
- write_nic_word(dev, 0x5e, 0x01);
- force_pci_posting(dev);
- mdelay(1);
- write_nic_word(dev, 0xfe, 0x10);
- force_pci_posting(dev);
- mdelay(1);
- write_nic_word(dev, 0x5e, 0x00);
- force_pci_posting(dev);
- mdelay(1);
- */
- write_nic_byte(dev, 0xec, 0x3f); /* Disable early TX */
- }
-
- if(priv->card_8185){
-
- txconf = txconf &~ (1<<TCR_PROBE_NOTIMESTAMP_SHIFT);
-
- }else{
-
- if(hwseqnum)
- txconf= txconf &~ (1<<TX_CONF_HEADER_AUTOICREMENT_SHIFT);
- else
- txconf= txconf | (1<<TX_CONF_HEADER_AUTOICREMENT_SHIFT);
- }
-
- txconf = txconf &~ TX_LOOPBACK_MASK;
- txconf = txconf | (TX_LOOPBACK_NONE <<TX_LOOPBACK_SHIFT);
- txconf = txconf &~ TCR_DPRETRY_MASK;
- txconf = txconf &~ TCR_RTSRETRY_MASK;
- txconf = txconf | (priv->retry_data<<TX_DPRETRY_SHIFT);
- txconf = txconf | (priv->retry_rts<<TX_RTSRETRY_SHIFT);
- txconf = txconf &~ (1<<TX_NOCRC_SHIFT);
-
- if(priv->card_8185){
- if(priv->hw_plcp_len)
- txconf = txconf &~ TCR_PLCP_LEN;
- else
- txconf = txconf | TCR_PLCP_LEN;
- }else{
- txconf = txconf &~ TCR_SAT;
- }
- txconf = txconf &~ TCR_MXDMA_MASK;
- txconf = txconf | (TCR_MXDMA_2048<<TCR_MXDMA_SHIFT);
- txconf = txconf | TCR_CWMIN;
- txconf = txconf | TCR_DISCW;
-
-// if(priv->ieee80211->hw_wep)
-// txconf=txconf &~ (1<<TX_NOICV_SHIFT);
-// else
- txconf=txconf | (1<<TX_NOICV_SHIFT);
-
- write_nic_dword(dev,TX_CONF,txconf);
-#endif
-
write_nic_dword(dev, TCR, priv->TransmitConfig);
byte = read_nic_byte(dev, MSR);
byte |= MSR_LINK_ENEDCA;
}
-#endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff