#include <linux/sysrq.h>
#include <linux/mca.h>
#include <linux/delay.h>
-#include <linux/device.h>
+#include <linux/platform_device.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_reg.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
+#include <linux/nmi.h>
#include <asm/io.h>
#include <asm/irq.h>
*/
#define is_real_interrupt(irq) ((irq) != 0)
-/*
- * This converts from our new CONFIG_ symbols to the symbols
- * that asm/serial.h expects. You _NEED_ to comment out the
- * linux/config.h include contained inside asm/serial.h for
- * this to work.
- */
-#undef CONFIG_SERIAL_MANY_PORTS
-#undef CONFIG_SERIAL_DETECT_IRQ
-#undef CONFIG_SERIAL_MULTIPORT
-#undef CONFIG_HUB6
-
#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
#define CONFIG_SERIAL_DETECT_IRQ 1
#endif
-#ifdef CONFIG_SERIAL_8250_MULTIPORT
-#define CONFIG_SERIAL_MULTIPORT 1
-#endif
#ifdef CONFIG_SERIAL_8250_MANY_PORTS
#define CONFIG_SERIAL_MANY_PORTS 1
#endif
SERIAL_PORT_DFNS /* defined in asm/serial.h */
};
-#define UART_NR (ARRAY_SIZE(old_serial_port) + CONFIG_SERIAL_8250_NR_UARTS)
+#define UART_NR CONFIG_SERIAL_8250_NR_UARTS
#ifdef CONFIG_SERIAL_8250_RSA
struct uart_port port;
struct timer_list timer; /* "no irq" timer */
struct list_head list; /* ports on this IRQ */
- unsigned int capabilities; /* port capabilities */
+ unsigned short capabilities; /* port capabilities */
+ unsigned short bugs; /* port bugs */
unsigned int tx_loadsz; /* transmit fifo load size */
- unsigned short rev;
unsigned char acr;
unsigned char ier;
unsigned char lcr;
},
};
+#ifdef CONFIG_SERIAL_8250_AU1X00
+
+/* Au1x00 UART hardware has a weird register layout */
+static const u8 au_io_in_map[] = {
+ [UART_RX] = 0,
+ [UART_IER] = 2,
+ [UART_IIR] = 3,
+ [UART_LCR] = 5,
+ [UART_MCR] = 6,
+ [UART_LSR] = 7,
+ [UART_MSR] = 8,
+};
+
+static const u8 au_io_out_map[] = {
+ [UART_TX] = 1,
+ [UART_IER] = 2,
+ [UART_FCR] = 4,
+ [UART_LCR] = 5,
+ [UART_MCR] = 6,
+};
+
+/* sane hardware needs no mapping */
+static inline int map_8250_in_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_AU)
+ return offset;
+ return au_io_in_map[offset];
+}
+
+static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_AU)
+ return offset;
+ return au_io_out_map[offset];
+}
+
+#else
+
+/* sane hardware needs no mapping */
+#define map_8250_in_reg(up, offset) (offset)
+#define map_8250_out_reg(up, offset) (offset)
+
+#endif
+
static _INLINE_ unsigned int serial_in(struct uart_8250_port *up, int offset)
{
- offset <<= up->port.regshift;
+ offset = map_8250_in_reg(up, offset) << up->port.regshift;
switch (up->port.iotype) {
case UPIO_HUB6:
case UPIO_MEM32:
return readl(up->port.membase + offset);
+#ifdef CONFIG_SERIAL_8250_AU1X00
+ case UPIO_AU:
+ return __raw_readl(up->port.membase + offset);
+#endif
+
default:
return inb(up->port.iobase + offset);
}
static _INLINE_ void
serial_out(struct uart_8250_port *up, int offset, int value)
{
- offset <<= up->port.regshift;
+ offset = map_8250_out_reg(up, offset) << up->port.regshift;
switch (up->port.iotype) {
case UPIO_HUB6:
writel(value, up->port.membase + offset);
break;
+#ifdef CONFIG_SERIAL_8250_AU1X00
+ case UPIO_AU:
+ __raw_writel(value, up->port.membase + offset);
+ break;
+#endif
+
default:
outb(value, up->port.iobase + offset);
}
if (id1 == 0x16 && id2 == 0xC9 &&
(id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) {
up->port.type = PORT_16C950;
- up->rev = rev | (id3 << 8);
+
+ /*
+ * Enable work around for the Oxford Semiconductor 952 rev B
+ * chip which causes it to seriously miscalculate baud rates
+ * when DLL is 0.
+ */
+ if (id3 == 0x52 && rev == 0x01)
+ up->bugs |= UART_BUG_QUOT;
return;
}
id2 = id1 >> 8;
if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) {
- if (id2 == 0x10)
- up->rev = id1 & 255;
up->port.type = PORT_16850;
return;
}
* from EXCR1. Switch back to bank 0, change it in MCR. Then
* switch back to bank 2, read it from EXCR1 again and check
* it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
- * On PowerPC we don't want to change baud_base, as we have
- * a number of different divisors. -- Tom Rini
*/
serial_outp(up, UART_LCR, 0);
status1 = serial_in(up, UART_MCR);
serial_outp(up, UART_MCR, status1);
if ((status2 ^ status1) & UART_MCR_LOOP) {
-#ifndef CONFIG_PPC
+ unsigned short quot;
+
serial_outp(up, UART_LCR, 0xE0);
+
+ quot = serial_inp(up, UART_DLM) << 8;
+ quot += serial_inp(up, UART_DLL);
+ quot <<= 3;
+
status1 = serial_in(up, 0x04); /* EXCR1 */
status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */
serial_outp(up, 0x04, status1);
+
+ serial_outp(up, UART_DLL, quot & 0xff);
+ serial_outp(up, UART_DLM, quot >> 8);
+
serial_outp(up, UART_LCR, 0);
- up->port.uartclk = 921600*16;
-#endif
+ up->port.uartclk = 921600*16;
up->port.type = PORT_NS16550A;
up->capabilities |= UART_NATSEMI;
return;
// save_flags(flags); cli();
up->capabilities = 0;
+ up->bugs = 0;
if (!(up->port.flags & UPF_BUGGY_UART)) {
/*
/*
* We're pretty sure there's a port here. Lets find out what
* type of port it is. The IIR top two bits allows us to find
- * out if its 8250 or 16450, 16550, 16550A or later. This
+ * out if it's 8250 or 16450, 16550, 16550A or later. This
* determines what we test for next.
*
* We also initialise the EFR (if any) to zero for later. The
}
}
#endif
+
+#ifdef CONFIG_SERIAL_8250_AU1X00
+ /* if access method is AU, it is a 16550 with a quirk */
+ if (up->port.type == PORT_16550A && up->port.iotype == UPIO_AU)
+ up->bugs |= UART_BUG_NOMSR;
+#endif
+
serial_outp(up, UART_LCR, save_lcr);
if (up->capabilities != uart_config[up->port.type].flags) {
up->port.irq = (irq > 0) ? irq : 0;
}
-static void serial8250_stop_tx(struct uart_port *port, unsigned int tty_stop)
+static inline void __stop_tx(struct uart_8250_port *p)
+{
+ if (p->ier & UART_IER_THRI) {
+ p->ier &= ~UART_IER_THRI;
+ serial_out(p, UART_IER, p->ier);
+ }
+}
+
+static void serial8250_stop_tx(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
- if (up->ier & UART_IER_THRI) {
- up->ier &= ~UART_IER_THRI;
- serial_out(up, UART_IER, up->ier);
- }
+ __stop_tx(up);
/*
- * We only do this from uart_stop - if we run out of
- * characters to send, we don't want to prevent the
- * FIFO from emptying.
+ * We really want to stop the transmitter from sending.
*/
- if (up->port.type == PORT_16C950 && tty_stop) {
+ if (up->port.type == PORT_16C950) {
up->acr |= UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
}
-static void serial8250_start_tx(struct uart_port *port, unsigned int tty_start)
+static void transmit_chars(struct uart_8250_port *up);
+
+static void serial8250_start_tx(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
if (!(up->ier & UART_IER_THRI)) {
up->ier |= UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
+
+ if (up->bugs & UART_BUG_TXEN) {
+ unsigned char lsr, iir;
+ lsr = serial_in(up, UART_LSR);
+ iir = serial_in(up, UART_IIR);
+ if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
+ transmit_chars(up);
+ }
}
+
/*
- * We only do this from uart_start
+ * Re-enable the transmitter if we disabled it.
*/
- if (tty_start && up->port.type == PORT_16C950) {
+ if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
up->acr &= ~UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
+ /* no MSR capabilities */
+ if (up->bugs & UART_BUG_NOMSR)
+ return;
+
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
}
up->port.x_char = 0;
return;
}
- if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
- serial8250_stop_tx(&up->port, 0);
+ if (uart_tx_stopped(&up->port)) {
+ serial8250_stop_tx(&up->port);
+ return;
+ }
+ if (uart_circ_empty(xmit)) {
+ __stop_tx(up);
return;
}
DEBUG_INTR("THRE...");
if (uart_circ_empty(xmit))
- serial8250_stop_tx(&up->port, 0);
+ __stop_tx(up);
}
static _INLINE_ void check_modem_status(struct uart_8250_port *up)
static unsigned int serial8250_get_mctrl(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned long flags;
unsigned char status;
unsigned int ret;
- spin_lock_irqsave(&up->port.lock, flags);
status = serial_in(up, UART_MSR);
- spin_unlock_irqrestore(&up->port.lock, flags);
ret = 0;
if (status & UART_MSR_DCD)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
+ unsigned char lsr, iir;
int retval;
up->capabilities = uart_config[up->port.type].flags;
up->port.mctrl |= TIOCM_OUT2;
serial8250_set_mctrl(&up->port, up->port.mctrl);
+
+ /*
+ * Do a quick test to see if we receive an
+ * interrupt when we enable the TX irq.
+ */
+ serial_outp(up, UART_IER, UART_IER_THRI);
+ lsr = serial_in(up, UART_LSR);
+ iir = serial_in(up, UART_IIR);
+ serial_outp(up, UART_IER, 0);
+
+ if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) {
+ if (!(up->bugs & UART_BUG_TXEN)) {
+ up->bugs |= UART_BUG_TXEN;
+ pr_debug("ttyS%d - enabling bad tx status workarounds\n",
+ port->line);
+ }
+ } else {
+ up->bugs &= ~UART_BUG_TXEN;
+ }
+
spin_unlock_irqrestore(&up->port.lock, flags);
/*
switch (termios->c_cflag & CSIZE) {
case CS5:
- cval = 0x00;
+ cval = UART_LCR_WLEN5;
break;
case CS6:
- cval = 0x01;
+ cval = UART_LCR_WLEN6;
break;
case CS7:
- cval = 0x02;
+ cval = UART_LCR_WLEN7;
break;
default:
case CS8:
- cval = 0x03;
+ cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
- cval |= 0x04;
+ cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
quot = serial8250_get_divisor(port, baud);
/*
- * Work around a bug in the Oxford Semiconductor 952 rev B
- * chip which causes it to seriously miscalculate baud rates
- * when DLL is 0.
+ * Oxford Semi 952 rev B workaround
*/
- if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
- up->rev == 0x5201)
+ if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
quot ++;
if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) {
* CTS flow control flag and modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
- if (UART_ENABLE_MS(&up->port, termios->c_cflag))
+ if (!(up->bugs & UART_BUG_NOMSR) &&
+ UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
if (up->capabilities & UART_CAP_UUE)
up->ier |= UART_IER_UUE | UART_IER_RTOIE;
up->port.ops = &serial8250_pops;
}
- for (i = 0, up = serial8250_ports; i < ARRAY_SIZE(old_serial_port);
+ for (i = 0, up = serial8250_ports;
+ i < ARRAY_SIZE(old_serial_port) && i < UART_NR;
i++, up++) {
up->port.iobase = old_serial_port[i].port;
up->port.irq = irq_canonicalize(old_serial_port[i].irq);
unsigned int ier;
int i;
+ touch_nmi_watchdog();
+
/*
* First save the UER then disable the interrupts
*/
* list is terminated with a zero flags entry, which means we expect
* all entries to have at least UPF_BOOT_AUTOCONF set.
*/
-static int __devinit serial8250_probe(struct device *dev)
+static int __devinit serial8250_probe(struct platform_device *dev)
{
- struct plat_serial8250_port *p = dev->platform_data;
+ struct plat_serial8250_port *p = dev->dev.platform_data;
struct uart_port port;
+ int ret, i;
memset(&port, 0, sizeof(struct uart_port));
- for (; p && p->flags != 0; p++) {
+ for (i = 0; p && p->flags != 0; p++, i++) {
port.iobase = p->iobase;
port.membase = p->membase;
port.irq = p->irq;
port.iotype = p->iotype;
port.flags = p->flags;
port.mapbase = p->mapbase;
- port.dev = dev;
+ port.hub6 = p->hub6;
+ port.dev = &dev->dev;
if (share_irqs)
port.flags |= UPF_SHARE_IRQ;
- serial8250_register_port(&port);
+ ret = serial8250_register_port(&port);
+ if (ret < 0) {
+ dev_err(&dev->dev, "unable to register port at index %d "
+ "(IO%lx MEM%lx IRQ%d): %d\n", i,
+ p->iobase, p->mapbase, p->irq, ret);
+ }
}
return 0;
}
/*
* Remove serial ports registered against a platform device.
*/
-static int __devexit serial8250_remove(struct device *dev)
+static int __devexit serial8250_remove(struct platform_device *dev)
{
int i;
for (i = 0; i < UART_NR; i++) {
struct uart_8250_port *up = &serial8250_ports[i];
- if (up->port.dev == dev)
+ if (up->port.dev == &dev->dev)
serial8250_unregister_port(i);
}
return 0;
}
-static int serial8250_suspend(struct device *dev, pm_message_t state, u32 level)
+static int serial8250_suspend(struct platform_device *dev, pm_message_t state)
{
int i;
- if (level != SUSPEND_DISABLE)
- return 0;
-
for (i = 0; i < UART_NR; i++) {
struct uart_8250_port *up = &serial8250_ports[i];
- if (up->port.type != PORT_UNKNOWN && up->port.dev == dev)
+ if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
uart_suspend_port(&serial8250_reg, &up->port);
}
return 0;
}
-static int serial8250_resume(struct device *dev, u32 level)
+static int serial8250_resume(struct platform_device *dev)
{
int i;
- if (level != RESUME_ENABLE)
- return 0;
-
for (i = 0; i < UART_NR; i++) {
struct uart_8250_port *up = &serial8250_ports[i];
- if (up->port.type != PORT_UNKNOWN && up->port.dev == dev)
+ if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
uart_resume_port(&serial8250_reg, &up->port);
}
return 0;
}
-static struct device_driver serial8250_isa_driver = {
- .name = "serial8250",
- .bus = &platform_bus_type,
+static struct platform_driver serial8250_isa_driver = {
.probe = serial8250_probe,
.remove = __devexit_p(serial8250_remove),
.suspend = serial8250_suspend,
.resume = serial8250_resume,
+ .driver = {
+ .name = "serial8250",
+ },
};
/*
goto out;
serial8250_isa_devs = platform_device_register_simple("serial8250",
- -1, NULL, 0);
+ PLAT8250_DEV_LEGACY, NULL, 0);
if (IS_ERR(serial8250_isa_devs)) {
ret = PTR_ERR(serial8250_isa_devs);
goto unreg;
serial8250_register_ports(&serial8250_reg, &serial8250_isa_devs->dev);
- ret = driver_register(&serial8250_isa_driver);
+ ret = platform_driver_register(&serial8250_isa_driver);
if (ret == 0)
goto out;
*/
serial8250_isa_devs = NULL;
- driver_unregister(&serial8250_isa_driver);
+ platform_driver_unregister(&serial8250_isa_driver);
platform_device_unregister(isa_dev);
uart_unregister_driver(&serial8250_reg);
MODULE_PARM_DESC(probe_rsa, "Probe I/O ports for RSA");
#endif
MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR);
-
-/**
- * register_serial - configure a 16x50 serial port at runtime
- * @req: request structure
- *
- * Configure the serial port specified by the request. If the
- * port exists and is in use an error is returned. If the port
- * is not currently in the table it is added.
- *
- * The port is then probed and if necessary the IRQ is autodetected
- * If this fails an error is returned.
- *
- * On success the port is ready to use and the line number is returned.
- *
- * Note: this function is deprecated - use serial8250_register_port
- * instead.
- */
-int register_serial(struct serial_struct *req)
-{
- struct uart_port port;
-
- port.iobase = req->port;
- port.membase = req->iomem_base;
- port.irq = req->irq;
- port.uartclk = req->baud_base * 16;
- port.fifosize = req->xmit_fifo_size;
- port.regshift = req->iomem_reg_shift;
- port.iotype = req->io_type;
- port.flags = req->flags | UPF_BOOT_AUTOCONF;
- port.mapbase = req->iomap_base;
- port.dev = NULL;
-
- if (share_irqs)
- port.flags |= UPF_SHARE_IRQ;
-
- if (HIGH_BITS_OFFSET)
- port.iobase |= (long) req->port_high << HIGH_BITS_OFFSET;
-
- /*
- * If a clock rate wasn't specified by the low level driver, then
- * default to the standard clock rate. This should be 115200 (*16)
- * and should not depend on the architecture's BASE_BAUD definition.
- * However, since this API will be deprecated, it's probably a
- * better idea to convert the drivers to use the new API
- * (serial8250_register_port and serial8250_unregister_port).
- */
- if (port.uartclk == 0) {
- printk(KERN_WARNING
- "Serial: registering port at [%08x,%08lx,%p] irq %d with zero baud_base\n",
- port.iobase, port.mapbase, port.membase, port.irq);
- printk(KERN_WARNING "Serial: see %s:%d for more information\n",
- __FILE__, __LINE__);
- dump_stack();
-
- /*
- * Fix it up for now, but this is only a temporary measure.
- */
- port.uartclk = BASE_BAUD * 16;
- }
-
- return serial8250_register_port(&port);
-}
-EXPORT_SYMBOL(register_serial);
-
-/**
- * unregister_serial - remove a 16x50 serial port at runtime
- * @line: serial line number
- *
- * Remove one serial port. This may not be called from interrupt
- * context. We hand the port back to our local PM control.
- *
- * Note: this function is deprecated - use serial8250_unregister_port
- * instead.
- */
-void unregister_serial(int line)
-{
- serial8250_unregister_port(line);
-}
-EXPORT_SYMBOL(unregister_serial);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff