#include <linux/delay.h>
#include <linux/acpi.h>
#include <linux/kallsyms.h>
+#include <linux/dmi.h>
+#include <linux/pci-aspm.h>
+#include <linux/ioport.h>
+#include <asm/dma.h> /* isa_dma_bridge_buggy */
#include "pci.h"
+/*
+ * This quirk function disables memory decoding and releases memory resources
+ * of the device specified by kernel's boot parameter 'pci=resource_alignment='.
+ * It also rounds up size to specified alignment.
+ * Later on, the kernel will assign page-aligned memory resource back
+ * to the device.
+ */
+static void __devinit quirk_resource_alignment(struct pci_dev *dev)
+{
+ int i;
+ struct resource *r;
+ resource_size_t align, size;
+ u16 command;
+
+ if (!pci_is_reassigndev(dev))
+ return;
+
+ if (dev->hdr_type == PCI_HEADER_TYPE_NORMAL &&
+ (dev->class >> 8) == PCI_CLASS_BRIDGE_HOST) {
+ dev_warn(&dev->dev,
+ "Can't reassign resources to host bridge.\n");
+ return;
+ }
+
+ dev_info(&dev->dev,
+ "Disabling memory decoding and releasing memory resources.\n");
+ pci_read_config_word(dev, PCI_COMMAND, &command);
+ command &= ~PCI_COMMAND_MEMORY;
+ pci_write_config_word(dev, PCI_COMMAND, command);
+
+ align = pci_specified_resource_alignment(dev);
+ for (i=0; i < PCI_BRIDGE_RESOURCES; i++) {
+ r = &dev->resource[i];
+ if (!(r->flags & IORESOURCE_MEM))
+ continue;
+ size = resource_size(r);
+ if (size < align) {
+ size = align;
+ dev_info(&dev->dev,
+ "Rounding up size of resource #%d to %#llx.\n",
+ i, (unsigned long long)size);
+ }
+ r->end = size - 1;
+ r->start = 0;
+ }
+ /* Need to disable bridge's resource window,
+ * to enable the kernel to reassign new resource
+ * window later on.
+ */
+ if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE &&
+ (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+ for (i = PCI_BRIDGE_RESOURCES; i < PCI_NUM_RESOURCES; i++) {
+ r = &dev->resource[i];
+ if (!(r->flags & IORESOURCE_MEM))
+ continue;
+ r->end = resource_size(r) - 1;
+ r->start = 0;
+ }
+ pci_disable_bridge_window(dev);
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_resource_alignment);
+
/* The Mellanox Tavor device gives false positive parity errors
* Mark this device with a broken_parity_status, to allow
* PCI scanning code to "skip" this now blacklisted device.
while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) {
pci_read_config_byte(d, 0x82, &dlc);
if (!(dlc & 1<<1)) {
- dev_err(&d->dev, "PIIX3: Enabling Passive Release\n");
+ dev_info(&d->dev, "PIIX3: Enabling Passive Release\n");
dlc |= 1<<1;
pci_write_config_byte(d, 0x82, dlc);
}
This appears to be BIOS not version dependent. So presumably there is a
chipset level fix */
-int isa_dma_bridge_buggy;
-EXPORT_SYMBOL(isa_dma_bridge_buggy);
static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev)
{
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs);
-int pci_pci_problems;
-EXPORT_SYMBOL(pci_pci_problems);
-
/*
* Chipsets where PCI->PCI transfers vanish or hang
*/
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M);
+/*
+ * Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS
+ * ver. 1.33 20070103) don't set the correct ISA PCI region header info.
+ * BAR0 should be 8 bytes; instead, it may be set to something like 8k
+ * (which conflicts w/ BAR1's memory range).
+ */
+static void __devinit quirk_cs5536_vsa(struct pci_dev *dev)
+{
+ if (pci_resource_len(dev, 0) != 8) {
+ struct resource *res = &dev->resource[0];
+ res->end = res->start + 8 - 1;
+ dev_info(&dev->dev, "CS5536 ISA bridge bug detected "
+ "(incorrect header); workaround applied.\n");
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa);
+
static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region,
unsigned size, int nr, const char *name)
{
pcibios_bus_to_resource(dev, res, &bus_region);
pci_claim_resource(dev, nr);
- dev_info(&dev->dev, "quirk: region %04x-%04x claimed by %s\n", region, region + size - 1, name);
+ dev_info(&dev->dev, "quirk: %pR claimed by %s\n", res, name);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi);
-static void __devinit quirk_ich6_lpc_acpi(struct pci_dev *dev)
+static void __devinit ich6_lpc_acpi_gpio(struct pci_dev *dev)
{
u32 region;
pci_read_config_dword(dev, 0x48, ®ion);
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH6 GPIO");
}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich6_lpc_acpi);
+
+static void __devinit ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name, int dynsize)
+{
+ u32 val;
+ u32 size, base;
+
+ pci_read_config_dword(dev, reg, &val);
+
+ /* Enabled? */
+ if (!(val & 1))
+ return;
+ base = val & 0xfffc;
+ if (dynsize) {
+ /*
+ * This is not correct. It is 16, 32 or 64 bytes depending on
+ * register D31:F0:ADh bits 5:4.
+ *
+ * But this gets us at least _part_ of it.
+ */
+ size = 16;
+ } else {
+ size = 128;
+ }
+ base &= ~(size-1);
+
+ /* Just print it out for now. We should reserve it after more debugging */
+ dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base+size-1);
+}
+
+static void __devinit quirk_ich6_lpc(struct pci_dev *dev)
+{
+ /* Shared ACPI/GPIO decode with all ICH6+ */
+ ich6_lpc_acpi_gpio(dev);
+
+ /* ICH6-specific generic IO decode */
+ ich6_lpc_generic_decode(dev, 0x84, "LPC Generic IO decode 1", 0);
+ ich6_lpc_generic_decode(dev, 0x88, "LPC Generic IO decode 2", 1);
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc);
+
+static void __devinit ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name)
+{
+ u32 val;
+ u32 mask, base;
+
+ pci_read_config_dword(dev, reg, &val);
+
+ /* Enabled? */
+ if (!(val & 1))
+ return;
+
+ /*
+ * IO base in bits 15:2, mask in bits 23:18, both
+ * are dword-based
+ */
+ base = val & 0xfffc;
+ mask = (val >> 16) & 0xfc;
+ mask |= 3;
+
+ /* Just print it out for now. We should reserve it after more debugging */
+ dev_info(&dev->dev, "%s PIO at %04x (mask %04x)\n", name, base, mask);
+}
+
+/* ICH7-10 has the same common LPC generic IO decode registers */
+static void __devinit quirk_ich7_lpc(struct pci_dev *dev)
+{
+ /* We share the common ACPI/DPIO decode with ICH6 */
+ ich6_lpc_acpi_gpio(dev);
+
+ /* And have 4 ICH7+ generic decodes */
+ ich7_lpc_generic_decode(dev, 0x84, "ICH7 LPC Generic IO decode 1");
+ ich7_lpc_generic_decode(dev, 0x88, "ICH7 LPC Generic IO decode 2");
+ ich7_lpc_generic_decode(dev, 0x8c, "ICH7 LPC Generic IO decode 3");
+ ich7_lpc_generic_decode(dev, 0x90, "ICH7 LPC Generic IO decode 4");
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_1, quirk_ich7_lpc);
/*
* VIA ACPI: One IO region pointed to by longword at
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi);
+/*
+ * TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast back-to-back:
+ * Disable fast back-to-back on the secondary bus segment
+ */
+static void __devinit quirk_xio2000a(struct pci_dev *dev)
+{
+ struct pci_dev *pdev;
+ u16 command;
+
+ dev_warn(&dev->dev, "TI XIO2000a quirk detected; "
+ "secondary bus fast back-to-back transfers disabled\n");
+ list_for_each_entry(pdev, &dev->subordinate->devices, bus_list) {
+ pci_read_config_word(pdev, PCI_COMMAND, &command);
+ if (command & PCI_COMMAND_FAST_BACK)
+ pci_write_config_word(pdev, PCI_COMMAND, command & ~PCI_COMMAND_FAST_BACK);
+ }
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2000A,
+ quirk_xio2000a);
#ifdef CONFIG_X86_IO_APIC
sis_apic_bug = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw);
-
-#define AMD8131_revA0 0x01
-#define AMD8131_revB0 0x11
-#define AMD8131_MISC 0x40
-#define AMD8131_NIOAMODE_BIT 0
-static void quirk_amd_8131_ioapic(struct pci_dev *dev)
-{
- unsigned char tmp;
-
- if (nr_ioapics == 0)
- return;
-
- if (dev->revision == AMD8131_revA0 || dev->revision == AMD8131_revB0) {
- dev_info(&dev->dev, "Fixing up AMD8131 IOAPIC mode\n");
- pci_read_config_byte( dev, AMD8131_MISC, &tmp);
- tmp &= ~(1 << AMD8131_NIOAMODE_BIT);
- pci_write_config_byte( dev, AMD8131_MISC, tmp);
- }
-}
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_ioapic);
-DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_ioapic);
#endif /* CONFIG_X86_IO_APIC */
/*
static void __devinit quirk_amd_ide_mode(struct pci_dev *pdev)
{
- /* set sb600/sb700/sb800 sata to ahci mode */
+ /* set SBX00/Hudson-2 SATA in IDE mode to AHCI mode */
u8 tmp;
pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &tmp);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode);
/*
* Serverworks CSB5 IDE does not fully support native mode
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
+/*
+ * Some ATA devices break if put into D3
+ */
+
+static void __devinit quirk_no_ata_d3(struct pci_dev *pdev)
+{
+ /* Quirk the legacy ATA devices only. The AHCI ones are ok */
+ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE)
+ pdev->dev_flags |= PCI_DEV_FLAGS_NO_D3;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_ANY_ID, quirk_no_ata_d3);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, PCI_ANY_ID, quirk_no_ata_d3);
+/* ALi loses some register settings that we cannot then restore */
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, quirk_no_ata_d3);
+/* VIA comes back fine but we need to keep it alive or ACPI GTM failures
+ occur when mode detecting */
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_no_ata_d3);
+
/* This was originally an Alpha specific thing, but it really fits here.
* The i82375 PCI/EISA bridge appears as non-classified. Fix that.
*/
switch (dev->subsystem_device) {
case 0x1751: /* M2N notebook */
case 0x1821: /* M5N notebook */
+ case 0x1897: /* A6L notebook */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch (dev->subsystem_device) {
case 0x12bc: /* HP D330L */
case 0x12bd: /* HP D530 */
+ case 0x006a: /* HP Compaq nx9500 */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82875_HB)
* its on-board VGA controller */
asus_hides_smbus = 1;
}
+ else if (dev->device == PCI_DEVICE_ID_INTEL_82801DB_2)
+ switch(dev->subsystem_device) {
+ case 0x00b8: /* Compaq Evo D510 CMT */
+ case 0x00b9: /* Compaq Evo D510 SFF */
+ case 0x00ba: /* Compaq Evo D510 USDT */
+ /* Motherboard doesn't have Host bridge
+ * subvendor/subdevice IDs and on-board VGA
+ * controller is disabled if an AGP card is
+ * inserted, therefore checking USB UHCI
+ * Controller #1 */
+ asus_hides_smbus = 1;
+ }
+ else if (dev->device == PCI_DEVICE_ID_INTEL_82815_CGC)
+ switch (dev->subsystem_device) {
+ case 0x001A: /* Compaq Deskpro EN SSF P667 815E */
+ /* Motherboard doesn't have host bridge
+ * subvendor/subdevice IDs, therefore checking
+ * its on-board VGA controller */
+ asus_hides_smbus = 1;
+ }
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_2, asus_hides_smbus_hostbridge);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC, asus_hides_smbus_hostbridge);
static void asus_hides_smbus_lpc(struct pci_dev *dev)
{
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic);
#endif
-int pcie_mch_quirk;
-EXPORT_SYMBOL(pcie_mch_quirk);
-
static void __devinit quirk_pcie_mch(struct pci_dev *pdev)
{
- pcie_mch_quirk = 1;
+ pci_msi_off(pdev);
+ pdev->no_msi = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm);
+#ifdef CONFIG_X86_IO_APIC
+/*
+ * Boot interrupts on some chipsets cannot be turned off. For these chipsets,
+ * remap the original interrupt in the linux kernel to the boot interrupt, so
+ * that a PCI device's interrupt handler is installed on the boot interrupt
+ * line instead.
+ */
+static void quirk_reroute_to_boot_interrupts_intel(struct pci_dev *dev)
+{
+ if (noioapicquirk || noioapicreroute)
+ return;
+
+ dev->irq_reroute_variant = INTEL_IRQ_REROUTE_VARIANT;
+ dev_info(&dev->dev, "rerouting interrupts for [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel);
+
+/*
+ * On some chipsets we can disable the generation of legacy INTx boot
+ * interrupts.
+ */
+
+/*
+ * IO-APIC1 on 6300ESB generates boot interrupts, see intel order no
+ * 300641-004US, section 5.7.3.
+ */
+#define INTEL_6300_IOAPIC_ABAR 0x40
+#define INTEL_6300_DISABLE_BOOT_IRQ (1<<14)
+
+static void quirk_disable_intel_boot_interrupt(struct pci_dev *dev)
+{
+ u16 pci_config_word;
+
+ if (noioapicquirk)
+ return;
+
+ pci_read_config_word(dev, INTEL_6300_IOAPIC_ABAR, &pci_config_word);
+ pci_config_word |= INTEL_6300_DISABLE_BOOT_IRQ;
+ pci_write_config_word(dev, INTEL_6300_IOAPIC_ABAR, pci_config_word);
+
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt);
+
+/*
+ * disable boot interrupts on HT-1000
+ */
+#define BC_HT1000_FEATURE_REG 0x64
+#define BC_HT1000_PIC_REGS_ENABLE (1<<0)
+#define BC_HT1000_MAP_IDX 0xC00
+#define BC_HT1000_MAP_DATA 0xC01
+
+static void quirk_disable_broadcom_boot_interrupt(struct pci_dev *dev)
+{
+ u32 pci_config_dword;
+ u8 irq;
+
+ if (noioapicquirk)
+ return;
+
+ pci_read_config_dword(dev, BC_HT1000_FEATURE_REG, &pci_config_dword);
+ pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword |
+ BC_HT1000_PIC_REGS_ENABLE);
+
+ for (irq = 0x10; irq < 0x10 + 32; irq++) {
+ outb(irq, BC_HT1000_MAP_IDX);
+ outb(0x00, BC_HT1000_MAP_DATA);
+ }
+
+ pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword);
+
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt);
+
+/*
+ * disable boot interrupts on AMD and ATI chipsets
+ */
+/*
+ * NOIOAMODE needs to be disabled to disable "boot interrupts". For AMD 8131
+ * rev. A0 and B0, NOIOAMODE needs to be disabled anyway to fix IO-APIC mode
+ * (due to an erratum).
+ */
+#define AMD_813X_MISC 0x40
+#define AMD_813X_NOIOAMODE (1<<0)
+#define AMD_813X_REV_B1 0x12
+#define AMD_813X_REV_B2 0x13
+
+static void quirk_disable_amd_813x_boot_interrupt(struct pci_dev *dev)
+{
+ u32 pci_config_dword;
+
+ if (noioapicquirk)
+ return;
+ if ((dev->revision == AMD_813X_REV_B1) ||
+ (dev->revision == AMD_813X_REV_B2))
+ return;
+
+ pci_read_config_dword(dev, AMD_813X_MISC, &pci_config_dword);
+ pci_config_dword &= ~AMD_813X_NOIOAMODE;
+ pci_write_config_dword(dev, AMD_813X_MISC, pci_config_dword);
+
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+
+#define AMD_8111_PCI_IRQ_ROUTING 0x56
+
+static void quirk_disable_amd_8111_boot_interrupt(struct pci_dev *dev)
+{
+ u16 pci_config_word;
+
+ if (noioapicquirk)
+ return;
+
+ pci_read_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, &pci_config_word);
+ if (!pci_config_word) {
+ dev_info(&dev->dev, "boot interrupts on device [%04x:%04x] "
+ "already disabled\n", dev->vendor, dev->device);
+ return;
+ }
+ pci_write_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, 0);
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt);
+#endif /* CONFIG_X86_IO_APIC */
+
/*
* Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size
* but the PIO transfers won't work if BAR0 falls at the odd 8 bytes.
* of parallel ports and <S> is the number of serial ports.
*/
switch (dev->device) {
+ case PCI_DEVICE_ID_NETMOS_9835:
+ /* Well, this rule doesn't hold for the following 9835 device */
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM &&
+ dev->subsystem_device == 0x0299)
+ return;
case PCI_DEVICE_ID_NETMOS_9735:
case PCI_DEVICE_ID_NETMOS_9745:
- case PCI_DEVICE_ID_NETMOS_9835:
case PCI_DEVICE_ID_NETMOS_9845:
case PCI_DEVICE_ID_NETMOS_9855:
if ((dev->class >> 8) == PCI_CLASS_COMMUNICATION_SERIAL &&
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_e100_interrupt);
+/*
+ * The 82575 and 82598 may experience data corruption issues when transitioning
+ * out of L0S. To prevent this we need to disable L0S on the pci-e link
+ */
+static void __devinit quirk_disable_aspm_l0s(struct pci_dev *dev)
+{
+ dev_info(&dev->dev, "Disabling L0s\n");
+ pci_disable_link_state(dev, PCIE_LINK_STATE_L0S);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a7, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a9, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10b6, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c6, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c7, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c8, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10d6, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10db, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10dd, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10e1, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10ec, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s);
+
static void __devinit fixup_rev1_53c810(struct pci_dev* dev)
{
/* rev 1 ncr53c810 chips don't set the class at all which means
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
-static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end)
-{
- while (f < end) {
- if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) &&
- (f->device == dev->device || f->device == (u16) PCI_ANY_ID)) {
-#ifdef DEBUG
- dev_dbg(&dev->dev, "calling ");
- print_fn_descriptor_symbol("%s\n", f->hook);
-#endif
- f->hook(dev);
- }
- f++;
- }
-}
-
-extern struct pci_fixup __start_pci_fixups_early[];
-extern struct pci_fixup __end_pci_fixups_early[];
-extern struct pci_fixup __start_pci_fixups_header[];
-extern struct pci_fixup __end_pci_fixups_header[];
-extern struct pci_fixup __start_pci_fixups_final[];
-extern struct pci_fixup __end_pci_fixups_final[];
-extern struct pci_fixup __start_pci_fixups_enable[];
-extern struct pci_fixup __end_pci_fixups_enable[];
-extern struct pci_fixup __start_pci_fixups_resume[];
-extern struct pci_fixup __end_pci_fixups_resume[];
-extern struct pci_fixup __start_pci_fixups_resume_early[];
-extern struct pci_fixup __end_pci_fixups_resume_early[];
-extern struct pci_fixup __start_pci_fixups_suspend[];
-extern struct pci_fixup __end_pci_fixups_suspend[];
-
-
-void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev)
-{
- struct pci_fixup *start, *end;
-
- switch(pass) {
- case pci_fixup_early:
- start = __start_pci_fixups_early;
- end = __end_pci_fixups_early;
- break;
-
- case pci_fixup_header:
- start = __start_pci_fixups_header;
- end = __end_pci_fixups_header;
- break;
-
- case pci_fixup_final:
- start = __start_pci_fixups_final;
- end = __end_pci_fixups_final;
- break;
-
- case pci_fixup_enable:
- start = __start_pci_fixups_enable;
- end = __end_pci_fixups_enable;
- break;
-
- case pci_fixup_resume:
- start = __start_pci_fixups_resume;
- end = __end_pci_fixups_resume;
- break;
-
- case pci_fixup_resume_early:
- start = __start_pci_fixups_resume_early;
- end = __end_pci_fixups_resume_early;
- break;
-
- case pci_fixup_suspend:
- start = __start_pci_fixups_suspend;
- end = __end_pci_fixups_suspend;
- break;
-
- default:
- /* stupid compiler warning, you would think with an enum... */
- return;
- }
- pci_do_fixups(dev, start, end);
-}
-EXPORT_SYMBOL(pci_fixup_device);
-
/* Enable 1k I/O space granularity on the Intel P64H2 */
static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
{
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching);
+/*
+ * For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
+ * VPD end tag will hang the device. This problem was initially
+ * observed when a vpd entry was created in sysfs
+ * ('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
+ * will dump 32k of data. Reading a full 32k will cause an access
+ * beyond the VPD end tag causing the device to hang. Once the device
+ * is hung, the bnx2 driver will not be able to reset the device.
+ * We believe that it is legal to read beyond the end tag and
+ * therefore the solution is to limit the read/write length.
+ */
+static void __devinit quirk_brcm_570x_limit_vpd(struct pci_dev *dev)
+{
+ /*
+ * Only disable the VPD capability for 5706, 5706S, 5708,
+ * 5708S and 5709 rev. A
+ */
+ if ((dev->device == PCI_DEVICE_ID_NX2_5706) ||
+ (dev->device == PCI_DEVICE_ID_NX2_5706S) ||
+ (dev->device == PCI_DEVICE_ID_NX2_5708) ||
+ (dev->device == PCI_DEVICE_ID_NX2_5708S) ||
+ ((dev->device == PCI_DEVICE_ID_NX2_5709) &&
+ (dev->revision & 0xf0) == 0x0)) {
+ if (dev->vpd)
+ dev->vpd->len = 0x80;
+ }
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5706,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5706S,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5708,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5708S,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5709,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5709S,
+ quirk_brcm_570x_limit_vpd);
+
+/* Originally in EDAC sources for i82875P:
+ * Intel tells BIOS developers to hide device 6 which
+ * configures the overflow device access containing
+ * the DRBs - this is where we expose device 6.
+ * http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm
+ */
+static void __devinit quirk_unhide_mch_dev6(struct pci_dev *dev)
+{
+ u8 reg;
+
+ if (pci_read_config_byte(dev, 0xF4, ®) == 0 && !(reg & 0x02)) {
+ dev_info(&dev->dev, "Enabling MCH 'Overflow' Device\n");
+ pci_write_config_byte(dev, 0xF4, reg | 0x02);
+ }
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB,
+ quirk_unhide_mch_dev6);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB,
+ quirk_unhide_mch_dev6);
+
+
#ifdef CONFIG_PCI_MSI
/* Some chipsets do not support MSI. We cannot easily rely on setting
* PCI_BUS_FLAGS_NO_MSI in its bus flags because there are actually
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS400_200, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3336, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disable_all_msi);
/* Disable MSI on chipsets that are known to not support it */
static void __devinit quirk_disable_msi(struct pci_dev *dev)
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE,
quirk_msi_ht_cap);
-
/* The nVidia CK804 chipset may have 2 HT MSI mappings.
* MSI are supported if the MSI capability set in any of these mappings.
*/
PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB,
ht_enable_msi_mapping);
-static void __devinit nv_msi_ht_cap_quirk(struct pci_dev *dev)
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE,
+ ht_enable_msi_mapping);
+
+/* The P5N32-SLI Premium motherboard from Asus has a problem with msi
+ * for the MCP55 NIC. It is not yet determined whether the msi problem
+ * also affects other devices. As for now, turn off msi for this device.
+ */
+static void __devinit nvenet_msi_disable(struct pci_dev *dev)
+{
+ if (dmi_name_in_vendors("P5N32-SLI PREMIUM")) {
+ dev_info(&dev->dev,
+ "Disabling msi for MCP55 NIC on P5N32-SLI Premium\n");
+ dev->no_msi = 1;
+ }
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
+ PCI_DEVICE_ID_NVIDIA_NVENET_15,
+ nvenet_msi_disable);
+
+static int __devinit ht_check_msi_mapping(struct pci_dev *dev)
+{
+ int pos, ttl = 48;
+ int found = 0;
+
+ /* check if there is HT MSI cap or enabled on this device */
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
+ while (pos && ttl--) {
+ u8 flags;
+
+ if (found < 1)
+ found = 1;
+ if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
+ &flags) == 0) {
+ if (flags & HT_MSI_FLAGS_ENABLE) {
+ if (found < 2) {
+ found = 2;
+ break;
+ }
+ }
+ }
+ pos = pci_find_next_ht_capability(dev, pos,
+ HT_CAPTYPE_MSI_MAPPING);
+ }
+
+ return found;
+}
+
+static int __devinit host_bridge_with_leaf(struct pci_dev *host_bridge)
+{
+ struct pci_dev *dev;
+ int pos;
+ int i, dev_no;
+ int found = 0;
+
+ dev_no = host_bridge->devfn >> 3;
+ for (i = dev_no + 1; i < 0x20; i++) {
+ dev = pci_get_slot(host_bridge->bus, PCI_DEVFN(i, 0));
+ if (!dev)
+ continue;
+
+ /* found next host bridge ?*/
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE);
+ if (pos != 0) {
+ pci_dev_put(dev);
+ break;
+ }
+
+ if (ht_check_msi_mapping(dev)) {
+ found = 1;
+ pci_dev_put(dev);
+ break;
+ }
+ pci_dev_put(dev);
+ }
+
+ return found;
+}
+
+#define PCI_HT_CAP_SLAVE_CTRL0 4 /* link control */
+#define PCI_HT_CAP_SLAVE_CTRL1 8 /* link control to */
+
+static int __devinit is_end_of_ht_chain(struct pci_dev *dev)
+{
+ int pos, ctrl_off;
+ int end = 0;
+ u16 flags, ctrl;
+
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE);
+
+ if (!pos)
+ goto out;
+
+ pci_read_config_word(dev, pos + PCI_CAP_FLAGS, &flags);
+
+ ctrl_off = ((flags >> 10) & 1) ?
+ PCI_HT_CAP_SLAVE_CTRL0 : PCI_HT_CAP_SLAVE_CTRL1;
+ pci_read_config_word(dev, pos + ctrl_off, &ctrl);
+
+ if (ctrl & (1 << 6))
+ end = 1;
+
+out:
+ return end;
+}
+
+static void __devinit nv_ht_enable_msi_mapping(struct pci_dev *dev)
{
struct pci_dev *host_bridge;
+ int pos;
+ int i, dev_no;
+ int found = 0;
+
+ dev_no = dev->devfn >> 3;
+ for (i = dev_no; i >= 0; i--) {
+ host_bridge = pci_get_slot(dev->bus, PCI_DEVFN(i, 0));
+ if (!host_bridge)
+ continue;
+
+ pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE);
+ if (pos != 0) {
+ found = 1;
+ break;
+ }
+ pci_dev_put(host_bridge);
+ }
+
+ if (!found)
+ return;
+
+ /* don't enable end_device/host_bridge with leaf directly here */
+ if (host_bridge == dev && is_end_of_ht_chain(host_bridge) &&
+ host_bridge_with_leaf(host_bridge))
+ goto out;
+
+ /* root did that ! */
+ if (msi_ht_cap_enabled(host_bridge))
+ goto out;
+
+ ht_enable_msi_mapping(dev);
+
+out:
+ pci_dev_put(host_bridge);
+}
+
+static void __devinit ht_disable_msi_mapping(struct pci_dev *dev)
+{
int pos, ttl = 48;
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
+ while (pos && ttl--) {
+ u8 flags;
+
+ if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
+ &flags) == 0) {
+ dev_info(&dev->dev, "Disabling HT MSI Mapping\n");
+
+ pci_write_config_byte(dev, pos + HT_MSI_FLAGS,
+ flags & ~HT_MSI_FLAGS_ENABLE);
+ }
+ pos = pci_find_next_ht_capability(dev, pos,
+ HT_CAPTYPE_MSI_MAPPING);
+ }
+}
+
+static void __devinit __nv_msi_ht_cap_quirk(struct pci_dev *dev, int all)
+{
+ struct pci_dev *host_bridge;
+ int pos;
+ int found;
+
+ /* check if there is HT MSI cap or enabled on this device */
+ found = ht_check_msi_mapping(dev);
+
+ /* no HT MSI CAP */
+ if (found == 0)
+ return;
+
/*
* HT MSI mapping should be disabled on devices that are below
* a non-Hypertransport host bridge. Locate the host bridge...
pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE);
if (pos != 0) {
/* Host bridge is to HT */
- ht_enable_msi_mapping(dev);
+ if (found == 1) {
+ /* it is not enabled, try to enable it */
+ if (all)
+ ht_enable_msi_mapping(dev);
+ else
+ nv_ht_enable_msi_mapping(dev);
+ }
return;
}
+ /* HT MSI is not enabled */
+ if (found == 1)
+ return;
+
/* Host bridge is not to HT, disable HT MSI mapping on this device */
- pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
- while (pos && ttl--) {
- u8 flags;
+ ht_disable_msi_mapping(dev);
+}
- if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
- &flags) == 0) {
- dev_info(&dev->dev, "Disabling HT MSI mapping");
- pci_write_config_byte(dev, pos + HT_MSI_FLAGS,
- flags & ~HT_MSI_FLAGS_ENABLE);
- }
- pos = pci_find_next_ht_capability(dev, pos,
- HT_CAPTYPE_MSI_MAPPING);
- }
+static void __devinit nv_msi_ht_cap_quirk_all(struct pci_dev *dev)
+{
+ return __nv_msi_ht_cap_quirk(dev, 1);
}
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk);
+
+static void __devinit nv_msi_ht_cap_quirk_leaf(struct pci_dev *dev)
+{
+ return __nv_msi_ht_cap_quirk(dev, 0);
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf);
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
static void __devinit quirk_msi_intx_disable_bug(struct pci_dev *dev)
{
quirk_msi_intx_disable_bug);
#endif /* CONFIG_PCI_MSI */
+
+#ifdef CONFIG_PCI_IOV
+
+/*
+ * For Intel 82576 SR-IOV NIC, if BIOS doesn't allocate resources for the
+ * SR-IOV BARs, zero the Flash BAR and program the SR-IOV BARs to use the
+ * old Flash Memory Space.
+ */
+static void __devinit quirk_i82576_sriov(struct pci_dev *dev)
+{
+ int pos, flags;
+ u32 bar, start, size;
+
+ if (PAGE_SIZE > 0x10000)
+ return;
+
+ flags = pci_resource_flags(dev, 0);
+ if ((flags & PCI_BASE_ADDRESS_SPACE) !=
+ PCI_BASE_ADDRESS_SPACE_MEMORY ||
+ (flags & PCI_BASE_ADDRESS_MEM_TYPE_MASK) !=
+ PCI_BASE_ADDRESS_MEM_TYPE_32)
+ return;
+
+ pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_SRIOV);
+ if (!pos)
+ return;
+
+ pci_read_config_dword(dev, pos + PCI_SRIOV_BAR, &bar);
+ if (bar & PCI_BASE_ADDRESS_MEM_MASK)
+ return;
+
+ start = pci_resource_start(dev, 1);
+ size = pci_resource_len(dev, 1);
+ if (!start || size != 0x400000 || start & (size - 1))
+ return;
+
+ pci_resource_flags(dev, 1) = 0;
+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, 0);
+ pci_write_config_dword(dev, pos + PCI_SRIOV_BAR, start);
+ pci_write_config_dword(dev, pos + PCI_SRIOV_BAR + 12, start + size / 2);
+
+ dev_info(&dev->dev, "use Flash Memory Space for SR-IOV BARs\n");
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10c9, quirk_i82576_sriov);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10e6, quirk_i82576_sriov);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10e7, quirk_i82576_sriov);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10e8, quirk_i82576_sriov);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x150a, quirk_i82576_sriov);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x150d, quirk_i82576_sriov);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1518, quirk_i82576_sriov);
+
+#endif /* CONFIG_PCI_IOV */
+
+static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f,
+ struct pci_fixup *end)
+{
+ while (f < end) {
+ if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) &&
+ (f->device == dev->device || f->device == (u16) PCI_ANY_ID)) {
+ dev_dbg(&dev->dev, "calling %pF\n", f->hook);
+ f->hook(dev);
+ }
+ f++;
+ }
+}
+
+extern struct pci_fixup __start_pci_fixups_early[];
+extern struct pci_fixup __end_pci_fixups_early[];
+extern struct pci_fixup __start_pci_fixups_header[];
+extern struct pci_fixup __end_pci_fixups_header[];
+extern struct pci_fixup __start_pci_fixups_final[];
+extern struct pci_fixup __end_pci_fixups_final[];
+extern struct pci_fixup __start_pci_fixups_enable[];
+extern struct pci_fixup __end_pci_fixups_enable[];
+extern struct pci_fixup __start_pci_fixups_resume[];
+extern struct pci_fixup __end_pci_fixups_resume[];
+extern struct pci_fixup __start_pci_fixups_resume_early[];
+extern struct pci_fixup __end_pci_fixups_resume_early[];
+extern struct pci_fixup __start_pci_fixups_suspend[];
+extern struct pci_fixup __end_pci_fixups_suspend[];
+
+
+void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev)
+{
+ struct pci_fixup *start, *end;
+
+ switch(pass) {
+ case pci_fixup_early:
+ start = __start_pci_fixups_early;
+ end = __end_pci_fixups_early;
+ break;
+
+ case pci_fixup_header:
+ start = __start_pci_fixups_header;
+ end = __end_pci_fixups_header;
+ break;
+
+ case pci_fixup_final:
+ start = __start_pci_fixups_final;
+ end = __end_pci_fixups_final;
+ break;
+
+ case pci_fixup_enable:
+ start = __start_pci_fixups_enable;
+ end = __end_pci_fixups_enable;
+ break;
+
+ case pci_fixup_resume:
+ start = __start_pci_fixups_resume;
+ end = __end_pci_fixups_resume;
+ break;
+
+ case pci_fixup_resume_early:
+ start = __start_pci_fixups_resume_early;
+ end = __end_pci_fixups_resume_early;
+ break;
+
+ case pci_fixup_suspend:
+ start = __start_pci_fixups_suspend;
+ end = __end_pci_fixups_suspend;
+ break;
+
+ default:
+ /* stupid compiler warning, you would think with an enum... */
+ return;
+ }
+ pci_do_fixups(dev, start, end);
+}
+EXPORT_SYMBOL(pci_fixup_device);
+
+static int __init pci_apply_final_quirks(void)
+{
+ struct pci_dev *dev = NULL;
+ u8 cls = 0;
+ u8 tmp;
+
+ if (pci_cache_line_size)
+ printk(KERN_DEBUG "PCI: CLS %u bytes\n",
+ pci_cache_line_size << 2);
+
+ while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev)) != NULL) {
+ pci_fixup_device(pci_fixup_final, dev);
+ /*
+ * If arch hasn't set it explicitly yet, use the CLS
+ * value shared by all PCI devices. If there's a
+ * mismatch, fall back to the default value.
+ */
+ if (!pci_cache_line_size) {
+ pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &tmp);
+ if (!cls)
+ cls = tmp;
+ if (!tmp || cls == tmp)
+ continue;
+
+ printk(KERN_DEBUG "PCI: CLS mismatch (%u != %u), "
+ "using %u bytes\n", cls << 2, tmp << 2,
+ pci_dfl_cache_line_size << 2);
+ pci_cache_line_size = pci_dfl_cache_line_size;
+ }
+ }
+ if (!pci_cache_line_size) {
+ printk(KERN_DEBUG "PCI: CLS %u bytes, default %u\n",
+ cls << 2, pci_dfl_cache_line_size << 2);
+ pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size;
+ }
+
+ return 0;
+}
+
+fs_initcall_sync(pci_apply_final_quirks);
+
+/*
+ * Followings are device-specific reset methods which can be used to
+ * reset a single function if other methods (e.g. FLR, PM D0->D3) are
+ * not available.
+ */
+static int reset_intel_generic_dev(struct pci_dev *dev, int probe)
+{
+ int pos;
+
+ /* only implement PCI_CLASS_SERIAL_USB at present */
+ if (dev->class == PCI_CLASS_SERIAL_USB) {
+ pos = pci_find_capability(dev, PCI_CAP_ID_VNDR);
+ if (!pos)
+ return -ENOTTY;
+
+ if (probe)
+ return 0;
+
+ pci_write_config_byte(dev, pos + 0x4, 1);
+ msleep(100);
+
+ return 0;
+ } else {
+ return -ENOTTY;
+ }
+}
+
+static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, int probe)
+{
+ int pos;
+
+ pos = pci_find_capability(dev, PCI_CAP_ID_EXP);
+ if (!pos)
+ return -ENOTTY;
+
+ if (probe)
+ return 0;
+
+ pci_write_config_word(dev, pos + PCI_EXP_DEVCTL,
+ PCI_EXP_DEVCTL_BCR_FLR);
+ msleep(100);
+
+ return 0;
+}
+
+#define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed
+
+static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
+ { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF,
+ reset_intel_82599_sfp_virtfn },
+ { PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
+ reset_intel_generic_dev },
+ { 0 }
+};
+
+int pci_dev_specific_reset(struct pci_dev *dev, int probe)
+{
+ const struct pci_dev_reset_methods *i;
+
+ for (i = pci_dev_reset_methods; i->reset; i++) {
+ if ((i->vendor == dev->vendor ||
+ i->vendor == (u16)PCI_ANY_ID) &&
+ (i->device == dev->device ||
+ i->device == (u16)PCI_ANY_ID))
+ return i->reset(dev, probe);
+ }
+
+ return -ENOTTY;
+}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff