+/* tasklet for iwlagn interrupt */
+static void iwl_irq_tasklet(struct iwl_priv *priv)
+{
+ u32 inta = 0;
+ u32 handled = 0;
+ unsigned long flags;
+#ifdef CONFIG_IWLWIFI_DEBUG
+ u32 inta_mask;
+#endif
+
+ spin_lock_irqsave(&priv->lock, flags);
+
+ /* Ack/clear/reset pending uCode interrupts.
+ * Note: Some bits in CSR_INT are "OR" of bits in CSR_FH_INT_STATUS,
+ */
+ iwl_write32(priv, CSR_INT, priv->inta);
+
+ inta = priv->inta;
+
+#ifdef CONFIG_IWLWIFI_DEBUG
+ if (iwl_get_debug_level(priv) & IWL_DL_ISR) {
+ /* just for debug */
+ inta_mask = iwl_read32(priv, CSR_INT_MASK);
+ IWL_DEBUG_ISR(priv, "inta 0x%08x, enabled 0x%08x\n ",
+ inta, inta_mask);
+ }
+#endif
+ /* saved interrupt in inta variable now we can reset priv->inta */
+ priv->inta = 0;
+
+ /* Now service all interrupt bits discovered above. */
+ if (inta & CSR_INT_BIT_HW_ERR) {
+ IWL_ERR(priv, "Hardware error detected. Restarting.\n");
+
+ /* Tell the device to stop sending interrupts */
+ iwl_disable_interrupts(priv);
+
+ priv->isr_stats.hw++;
+ iwl_irq_handle_error(priv);
+
+ handled |= CSR_INT_BIT_HW_ERR;
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return;
+ }
+
+#ifdef CONFIG_IWLWIFI_DEBUG
+ if (iwl_get_debug_level(priv) & (IWL_DL_ISR)) {
+ /* NIC fires this, but we don't use it, redundant with WAKEUP */
+ if (inta & CSR_INT_BIT_SCD) {
+ IWL_DEBUG_ISR(priv, "Scheduler finished to transmit "
+ "the frame/frames.\n");
+ priv->isr_stats.sch++;
+ }
+
+ /* Alive notification via Rx interrupt will do the real work */
+ if (inta & CSR_INT_BIT_ALIVE) {
+ IWL_DEBUG_ISR(priv, "Alive interrupt\n");
+ priv->isr_stats.alive++;
+ }
+ }
+#endif
+ /* Safely ignore these bits for debug checks below */
+ inta &= ~(CSR_INT_BIT_SCD | CSR_INT_BIT_ALIVE);
+
+ /* HW RF KILL switch toggled */
+ if (inta & CSR_INT_BIT_RF_KILL) {
+ int hw_rf_kill = 0;
+ if (!(iwl_read32(priv, CSR_GP_CNTRL) &
+ CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW))
+ hw_rf_kill = 1;
+
+ IWL_WARN(priv, "RF_KILL bit toggled to %s.\n",
+ hw_rf_kill ? "disable radio" : "enable radio");
+
+ priv->isr_stats.rfkill++;
+
+ /* driver only loads ucode once setting the interface up.
+ * the driver allows loading the ucode even if the radio
+ * is killed. Hence update the killswitch state here. The
+ * rfkill handler will care about restarting if needed.
+ */
+ if (!test_bit(STATUS_ALIVE, &priv->status)) {
+ if (hw_rf_kill)
+ set_bit(STATUS_RF_KILL_HW, &priv->status);
+ else
+ clear_bit(STATUS_RF_KILL_HW, &priv->status);
+ wiphy_rfkill_set_hw_state(priv->hw->wiphy, hw_rf_kill);
+ }
+
+ handled |= CSR_INT_BIT_RF_KILL;
+ }
+
+ /* Chip got too hot and stopped itself */
+ if (inta & CSR_INT_BIT_CT_KILL) {
+ IWL_ERR(priv, "Microcode CT kill error detected.\n");
+ priv->isr_stats.ctkill++;
+ handled |= CSR_INT_BIT_CT_KILL;
+ }
+
+ /* Error detected by uCode */
+ if (inta & CSR_INT_BIT_SW_ERR) {
+ IWL_ERR(priv, "Microcode SW error detected. "
+ " Restarting 0x%X.\n", inta);
+ priv->isr_stats.sw++;
+ priv->isr_stats.sw_err = inta;
+ iwl_irq_handle_error(priv);
+ handled |= CSR_INT_BIT_SW_ERR;
+ }
+
+ /* uCode wakes up after power-down sleep */
+ if (inta & CSR_INT_BIT_WAKEUP) {
+ IWL_DEBUG_ISR(priv, "Wakeup interrupt\n");
+ iwl_rx_queue_update_write_ptr(priv, &priv->rxq);
+ iwl_txq_update_write_ptr(priv, &priv->txq[0]);
+ iwl_txq_update_write_ptr(priv, &priv->txq[1]);
+ iwl_txq_update_write_ptr(priv, &priv->txq[2]);
+ iwl_txq_update_write_ptr(priv, &priv->txq[3]);
+ iwl_txq_update_write_ptr(priv, &priv->txq[4]);
+ iwl_txq_update_write_ptr(priv, &priv->txq[5]);
+
+ priv->isr_stats.wakeup++;
+
+ handled |= CSR_INT_BIT_WAKEUP;
+ }
+
+ /* All uCode command responses, including Tx command responses,
+ * Rx "responses" (frame-received notification), and other
+ * notifications from uCode come through here*/
+ if (inta & (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX |
+ CSR_INT_BIT_RX_PERIODIC)) {
+ IWL_DEBUG_ISR(priv, "Rx interrupt\n");
+ if (inta & (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX)) {
+ handled |= (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX);
+ iwl_write32(priv, CSR_FH_INT_STATUS,
+ CSR49_FH_INT_RX_MASK);
+ }
+ if (inta & CSR_INT_BIT_RX_PERIODIC) {
+ handled |= CSR_INT_BIT_RX_PERIODIC;
+ iwl_write32(priv, CSR_INT, CSR_INT_BIT_RX_PERIODIC);
+ }
+ /* Sending RX interrupt require many steps to be done in the
+ * the device:
+ * 1- write interrupt to current index in ICT table.
+ * 2- dma RX frame.
+ * 3- update RX shared data to indicate last write index.
+ * 4- send interrupt.
+ * This could lead to RX race, driver could receive RX interrupt
+ * but the shared data changes does not reflect this.
+ * this could lead to RX race, RX periodic will solve this race
+ */
+ iwl_write32(priv, CSR_INT_PERIODIC_REG,
+ CSR_INT_PERIODIC_DIS);
+ iwl_rx_handle(priv);
+ /* Only set RX periodic if real RX is received. */
+ if (inta & (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX))
+ iwl_write32(priv, CSR_INT_PERIODIC_REG,
+ CSR_INT_PERIODIC_ENA);
+
+ priv->isr_stats.rx++;
+ }
+
+ if (inta & CSR_INT_BIT_FH_TX) {
+ iwl_write32(priv, CSR_FH_INT_STATUS, CSR49_FH_INT_TX_MASK);
+ IWL_DEBUG_ISR(priv, "Tx interrupt\n");
+ priv->isr_stats.tx++;
+ handled |= CSR_INT_BIT_FH_TX;
+ /* FH finished to write, send event */
+ priv->ucode_write_complete = 1;
+ wake_up_interruptible(&priv->wait_command_queue);
+ }
+
+ if (inta & ~handled) {
+ IWL_ERR(priv, "Unhandled INTA bits 0x%08x\n", inta & ~handled);
+ priv->isr_stats.unhandled++;
+ }
+
+ if (inta & ~(priv->inta_mask)) {
+ IWL_WARN(priv, "Disabled INTA bits 0x%08x were pending\n",
+ inta & ~priv->inta_mask);
+ }
+
+
+ /* Re-enable all interrupts */
+ /* only Re-enable if diabled by irq */
+ if (test_bit(STATUS_INT_ENABLED, &priv->status))
+ iwl_enable_interrupts(priv);
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+}
+