#ifndef _SKY2_H
#define _SKY2_H
+#define ETH_JUMBO_MTU 9000 /* Maximum MTU supported */
+
/* PCI config registers */
-#define PCI_DEV_REG1 0x40
-#define PCI_DEV_REG2 0x44
-#define PCI_DEV_STATUS 0x7c
-#define PCI_OS_PCI_X (1<<26)
+enum {
+ PCI_DEV_REG1 = 0x40,
+ PCI_DEV_REG2 = 0x44,
+ PCI_DEV_STATUS = 0x7c,
+ PCI_DEV_REG3 = 0x80,
+ PCI_DEV_REG4 = 0x84,
+ PCI_DEV_REG5 = 0x88,
+ PCI_CFG_REG_0 = 0x90,
+ PCI_CFG_REG_1 = 0x94,
-#define PEX_LNK_STAT 0xf2
-#define PEX_UNC_ERR_STAT 0x104
-#define PEX_DEV_CTRL 0xe8
+ PSM_CONFIG_REG0 = 0x98,
+ PSM_CONFIG_REG1 = 0x9C,
+ PSM_CONFIG_REG2 = 0x160,
+ PSM_CONFIG_REG3 = 0x164,
+ PSM_CONFIG_REG4 = 0x168,
+
+};
/* Yukon-2 */
enum pci_dev_reg_1 {
PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */
PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */
+ PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */
PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */
PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */
+ PCI_Y2_PME_LEGACY= 1<<15, /* PCI Express legacy power management mode */
+
+ PCI_PHY_LNK_TIM_MSK= 3L<<8,/* Bit 9.. 8: GPHY Link Trigger Timer */
+ PCI_ENA_L1_EVENT = 1<<7, /* Enable PEX L1 Event */
+ PCI_ENA_GPHY_LNK = 1<<6, /* Enable PEX L1 on GPHY Link down */
+ PCI_FORCE_PEX_L1 = 1<<5, /* Force to PEX L1 */
};
enum pci_dev_reg_2 {
PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
};
+/* PCI_OUR_REG_3 32 bit Our Register 3 (Yukon-ECU only) */
+enum pci_dev_reg_3 {
+ P_CLK_ASF_REGS_DIS = 1<<18,/* Disable Clock ASF (Yukon-Ext.) */
+ P_CLK_COR_REGS_D0_DIS = 1<<17,/* Disable Clock Core Regs D0 */
+ P_CLK_MACSEC_DIS = 1<<17,/* Disable Clock MACSec (Yukon-Ext.) */
+ P_CLK_PCI_REGS_D0_DIS = 1<<16,/* Disable Clock PCI Regs D0 */
+ P_CLK_COR_YTB_ARB_DIS = 1<<15,/* Disable Clock YTB Arbiter */
+ P_CLK_MAC_LNK1_D3_DIS = 1<<14,/* Disable Clock MAC Link1 D3 */
+ P_CLK_COR_LNK1_D0_DIS = 1<<13,/* Disable Clock Core Link1 D0 */
+ P_CLK_MAC_LNK1_D0_DIS = 1<<12,/* Disable Clock MAC Link1 D0 */
+ P_CLK_COR_LNK1_D3_DIS = 1<<11,/* Disable Clock Core Link1 D3 */
+ P_CLK_PCI_MST_ARB_DIS = 1<<10,/* Disable Clock PCI Master Arb. */
+ P_CLK_COR_REGS_D3_DIS = 1<<9, /* Disable Clock Core Regs D3 */
+ P_CLK_PCI_REGS_D3_DIS = 1<<8, /* Disable Clock PCI Regs D3 */
+ P_CLK_REF_LNK1_GM_DIS = 1<<7, /* Disable Clock Ref. Link1 GMAC */
+ P_CLK_COR_LNK1_GM_DIS = 1<<6, /* Disable Clock Core Link1 GMAC */
+ P_CLK_PCI_COMMON_DIS = 1<<5, /* Disable Clock PCI Common */
+ P_CLK_COR_COMMON_DIS = 1<<4, /* Disable Clock Core Common */
+ P_CLK_PCI_LNK1_BMU_DIS = 1<<3, /* Disable Clock PCI Link1 BMU */
+ P_CLK_COR_LNK1_BMU_DIS = 1<<2, /* Disable Clock Core Link1 BMU */
+ P_CLK_PCI_LNK1_BIU_DIS = 1<<1, /* Disable Clock PCI Link1 BIU */
+ P_CLK_COR_LNK1_BIU_DIS = 1<<0, /* Disable Clock Core Link1 BIU */
+ PCIE_OUR3_WOL_D3_COLD_SET = P_CLK_ASF_REGS_DIS |
+ P_CLK_COR_REGS_D0_DIS |
+ P_CLK_COR_LNK1_D0_DIS |
+ P_CLK_MAC_LNK1_D0_DIS |
+ P_CLK_PCI_MST_ARB_DIS |
+ P_CLK_COR_COMMON_DIS |
+ P_CLK_COR_LNK1_BMU_DIS,
+};
+
+/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */
+enum pci_dev_reg_4 {
+ /* (Link Training & Status State Machine) */
+ P_PEX_LTSSM_STAT_MSK = 0x7fL<<25, /* Bit 31..25: PEX LTSSM Mask */
+#define P_PEX_LTSSM_STAT(x) ((x << 25) & P_PEX_LTSSM_STAT_MSK)
+ P_PEX_LTSSM_L1_STAT = 0x34,
+ P_PEX_LTSSM_DET_STAT = 0x01,
+ P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */
+ /* (Active State Power Management) */
+ P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */
+ P_ASPM_GPHY_LINK_DOWN = 1<<14, /* GPHY Link Down (A1 only) */
+ P_ASPM_INT_FIFO_EMPTY = 1<<13, /* Internal FIFO Empty (A1 only) */
+ P_ASPM_CLKRUN_REQUEST = 1<<12, /* CLKRUN Request (A1 only) */
+
+ P_ASPM_FORCE_CLKREQ_ENA = 1<<4, /* Force CLKREQ Enable (A1b only) */
+ P_ASPM_CLKREQ_PAD_CTL = 1<<3, /* CLKREQ PAD Control (A1 only) */
+ P_ASPM_A1_MODE_SELECT = 1<<2, /* A1 Mode Select (A1 only) */
+ P_CLK_GATE_PEX_UNIT_ENA = 1<<1, /* Enable Gate PEX Unit Clock */
+ P_CLK_GATE_ROOT_COR_ENA = 1<<0, /* Enable Gate Root Core Clock */
+ P_ASPM_CONTROL_MSK = P_FORCE_ASPM_REQUEST | P_ASPM_GPHY_LINK_DOWN
+ | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
+};
+
+/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */
+enum pci_dev_reg_5 {
+ /* Bit 31..27: for A3 & later */
+ P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */
+ P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */
+ P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */
+ P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */
+ /* Bit 26..16: Release Clock on Event */
+ P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */
+ P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */
+ P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */
+ P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */
+ P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */
+ P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */
+ P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */
+ P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */
+ P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */
+ P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */
+ P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */
+
+ /* Bit 10.. 0: Mask for Gate Clock */
+ P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */
+ P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */
+ P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */
+ P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */
+ P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */
+ P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */
+ P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */
+ P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */
+ P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */
+ P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */
+ P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */
+
+ PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET |
+ P_REL_INT_FIFO_N_EMPTY |
+ P_REL_PCIE_EXIT_L1_ST |
+ P_REL_PCIE_RX_EX_IDLE |
+ P_GAT_GPHY_N_REC_PACKET |
+ P_GAT_INT_FIFO_EMPTY |
+ P_GAT_PCIE_ENTER_L1_ST |
+ P_GAT_PCIE_RX_EL_IDLE,
+};
+
+/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */
+enum pci_cfg_reg1 {
+ P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */
+ /* Bit 23..21: Release Clock on Event */
+ P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */
+ P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */
+ P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */
+ /* Bit 20..18: Gate Clock on Event */
+ P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */
+ P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */
+ P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */
+ P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */
+ P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */
+
+ P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */
+
+ P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */
+ P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */
+
+ PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST |
+ P_CF1_REL_LDR_NOT_FIN |
+ P_CF1_REL_VMAIN_AVLBL |
+ P_CF1_REL_PCIE_RESET |
+ P_CF1_GAT_LDR_NOT_FIN |
+ P_CF1_GAT_PCIE_RESET |
+ P_CF1_PRST_PHY_CLKREQ |
+ P_CF1_ENA_CFG_LDR_DONE |
+ P_CF1_ENA_TXBMU_RD_IDLE |
+ P_CF1_ENA_TXBMU_WR_IDLE,
+};
+
+/* Yukon-Optima */
+enum {
+ PSM_CONFIG_REG1_AC_PRESENT_STATUS = 1<<31, /* AC Present Status */
+
+ PSM_CONFIG_REG1_PTP_CLK_SEL = 1<<29, /* PTP Clock Select */
+ PSM_CONFIG_REG1_PTP_MODE = 1<<28, /* PTP Mode */
+
+ PSM_CONFIG_REG1_MUX_PHY_LINK = 1<<27, /* PHY Energy Detect Event */
+
+ PSM_CONFIG_REG1_EN_PIN63_AC_PRESENT = 1<<26, /* Enable LED_DUPLEX for ac_present */
+ PSM_CONFIG_REG1_EN_PCIE_TIMER = 1<<25, /* Enable PCIe Timer */
+ PSM_CONFIG_REG1_EN_SPU_TIMER = 1<<24, /* Enable SPU Timer */
+ PSM_CONFIG_REG1_POLARITY_AC_PRESENT = 1<<23, /* AC Present Polarity */
+
+ PSM_CONFIG_REG1_EN_AC_PRESENT = 1<<21, /* Enable AC Present */
+
+ PSM_CONFIG_REG1_EN_GPHY_INT_PSM = 1<<20, /* Enable GPHY INT for PSM */
+ PSM_CONFIG_REG1_DIS_PSM_TIMER = 1<<19, /* Disable PSM Timer */
+};
+
+/* Yukon-Supreme */
+enum {
+ PSM_CONFIG_REG1_GPHY_ENERGY_STS = 1<<31, /* GPHY Energy Detect Status */
+
+ PSM_CONFIG_REG1_UART_MODE_MSK = 3<<29, /* UART_Mode */
+ PSM_CONFIG_REG1_CLK_RUN_ASF = 1<<28, /* Enable Clock Free Running for ASF Subsystem */
+ PSM_CONFIG_REG1_UART_CLK_DISABLE= 1<<27, /* Disable UART clock */
+ PSM_CONFIG_REG1_VAUX_ONE = 1<<26, /* Tie internal Vaux to 1'b1 */
+ PSM_CONFIG_REG1_UART_FC_RI_VAL = 1<<25, /* Default value for UART_RI_n */
+ PSM_CONFIG_REG1_UART_FC_DCD_VAL = 1<<24, /* Default value for UART_DCD_n */
+ PSM_CONFIG_REG1_UART_FC_DSR_VAL = 1<<23, /* Default value for UART_DSR_n */
+ PSM_CONFIG_REG1_UART_FC_CTS_VAL = 1<<22, /* Default value for UART_CTS_n */
+ PSM_CONFIG_REG1_LATCH_VAUX = 1<<21, /* Enable Latch current Vaux_avlbl */
+ PSM_CONFIG_REG1_FORCE_TESTMODE_INPUT= 1<<20, /* Force Testmode pin as input PAD */
+ PSM_CONFIG_REG1_UART_RST = 1<<19, /* UART_RST */
+ PSM_CONFIG_REG1_PSM_PCIE_L1_POL = 1<<18, /* PCIE L1 Event Polarity for PSM */
+ PSM_CONFIG_REG1_TIMER_STAT = 1<<17, /* PSM Timer Status */
+ PSM_CONFIG_REG1_GPHY_INT = 1<<16, /* GPHY INT Status */
+ PSM_CONFIG_REG1_FORCE_TESTMODE_ZERO= 1<<15, /* Force internal Testmode as 1'b0 */
+ PSM_CONFIG_REG1_EN_INT_ASPM_CLKREQ = 1<<14, /* ENABLE INT for CLKRUN on ASPM and CLKREQ */
+ PSM_CONFIG_REG1_EN_SND_TASK_ASPM_CLKREQ = 1<<13, /* ENABLE Snd_task for CLKRUN on ASPM and CLKREQ */
+ PSM_CONFIG_REG1_DIS_CLK_GATE_SND_TASK = 1<<12, /* Disable CLK_GATE control snd_task */
+ PSM_CONFIG_REG1_DIS_FF_CHIAN_SND_INTA = 1<<11, /* Disable flip-flop chain for sndmsg_inta */
+
+ PSM_CONFIG_REG1_DIS_LOADER = 1<<9, /* Disable Loader SM after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_DO_PWDN = 1<<8, /* Do Power Down, Start PSM Scheme */
+ PSM_CONFIG_REG1_DIS_PIG = 1<<7, /* Disable Plug-in-Go SM after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_DIS_PERST = 1<<6, /* Disable Internal PCIe Reset after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_EN_REG18_PD = 1<<5, /* Enable REG18 Power Down for PSM */
+ PSM_CONFIG_REG1_EN_PSM_LOAD = 1<<4, /* Disable EEPROM Loader after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_EN_PSM_HOT_RST = 1<<3, /* Enable PCIe Hot Reset for PSM */
+ PSM_CONFIG_REG1_EN_PSM_PERST = 1<<2, /* Enable PCIe Reset Event for PSM */
+ PSM_CONFIG_REG1_EN_PSM_PCIE_L1 = 1<<1, /* Enable PCIe L1 Event for PSM */
+ PSM_CONFIG_REG1_EN_PSM = 1<<0, /* Enable PSM Scheme */
+};
+
+/* PSM_CONFIG_REG4 0x0168 PSM Config Register 4 */
+enum {
+ /* PHY Link Detect Timer */
+ PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_MSK = 0xf<<4,
+ PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_BASE = 4,
+
+ PSM_CONFIG_REG4_DEBUG_TIMER = 1<<1, /* Debug Timer */
+ PSM_CONFIG_REG4_RST_PHY_LINK_DETECT = 1<<0, /* Reset GPHY Link Detect */
+};
+
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
PCI_STATUS_REC_TARGET_ABORT | \
PCI_STATUS_PARITY)
-enum pex_dev_ctrl {
- PEX_DC_MAX_RRS_MSK = 7<<12, /* Bit 14..12: Max. Read Request Size */
- PEX_DC_EN_NO_SNOOP = 1<<11,/* Enable No Snoop */
- PEX_DC_EN_AUX_POW = 1<<10,/* Enable AUX Power */
- PEX_DC_EN_PHANTOM = 1<<9, /* Enable Phantom Functions */
- PEX_DC_EN_EXT_TAG = 1<<8, /* Enable Extended Tag Field */
- PEX_DC_MAX_PLS_MSK = 7<<5, /* Bit 7.. 5: Max. Payload Size Mask */
- PEX_DC_EN_REL_ORD = 1<<4, /* Enable Relaxed Ordering */
- PEX_DC_EN_UNS_RQ_RP = 1<<3, /* Enable Unsupported Request Reporting */
- PEX_DC_EN_FAT_ER_RP = 1<<2, /* Enable Fatal Error Reporting */
- PEX_DC_EN_NFA_ER_RP = 1<<1, /* Enable Non-Fatal Error Reporting */
- PEX_DC_EN_COR_ER_RP = 1<<0, /* Enable Correctable Error Reporting */
-};
-#define PEX_DC_MAX_RD_RQ_SIZE(x) (((x)<<12) & PEX_DC_MAX_RRS_MSK)
-
-/* PEX_UNC_ERR_STAT PEX Uncorrectable Errors Status Register (Yukon-2) */
-enum pex_err {
- PEX_UNSUP_REQ = 1<<20, /* Unsupported Request Error */
-
- PEX_MALFOR_TLP = 1<<18, /* Malformed TLP */
-
- PEX_UNEXP_COMP = 1<<16, /* Unexpected Completion */
-
- PEX_COMP_TO = 1<<14, /* Completion Timeout */
- PEX_FLOW_CTRL_P = 1<<13, /* Flow Control Protocol Error */
- PEX_POIS_TLP = 1<<12, /* Poisoned TLP */
-
- PEX_DATA_LINK_P = 1<<4, /* Data Link Protocol Error */
- PEX_FATAL_ERRORS= (PEX_MALFOR_TLP | PEX_FLOW_CTRL_P | PEX_DATA_LINK_P),
-};
-
-
enum csr_regs {
B0_RAP = 0x0000,
B0_CTST = 0x0004,
- B0_Y2LED = 0x0005,
+
B0_POWER_CTRL = 0x0007,
B0_ISRC = 0x0008,
B0_IMSK = 0x000c,
B2_I2C_IRQ = 0x0168,
B2_I2C_SW = 0x016c,
+ Y2_PEX_PHY_DATA = 0x0170,
+ Y2_PEX_PHY_ADDR = 0x0172,
+
B3_RAM_ADDR = 0x0180,
B3_RAM_DATA_LO = 0x0184,
B3_RAM_DATA_HI = 0x0188,
B3_PA_CTRL = 0x01f0,
B3_PA_TEST = 0x01f2,
- Y2_CFG_SPC = 0x1c00,
+ Y2_CFG_SPC = 0x1c00, /* PCI config space region */
+ Y2_CFG_AER = 0x1d00, /* PCI Advanced Error Report region */
};
-/* B0_CTST 16 bit Control/Status register */
+/* B0_CTST 24 bit Control/Status register */
enum {
Y2_VMAIN_AVAIL = 1<<17,/* VMAIN available (YUKON-2 only) */
Y2_VAUX_AVAIL = 1<<16,/* VAUX available (YUKON-2 only) */
+ Y2_HW_WOL_ON = 1<<15,/* HW WOL On (Yukon-EC Ultra A1 only) */
+ Y2_HW_WOL_OFF = 1<<14,/* HW WOL On (Yukon-EC Ultra A1 only) */
Y2_ASF_ENABLE = 1<<13,/* ASF Unit Enable (YUKON-2 only) */
Y2_ASF_DISABLE = 1<<12,/* ASF Unit Disable (YUKON-2 only) */
Y2_CLK_RUN_ENA = 1<<11,/* CLK_RUN Enable (YUKON-2 only) */
CS_RST_SET = 1, /* Set Software reset */
};
-/* B0_LED 8 Bit LED register */
-enum {
-/* Bit 7.. 2: reserved */
- LED_STAT_ON = 1<<1, /* Status LED on */
- LED_STAT_OFF = 1, /* Status LED off */
-};
-
/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
enum {
PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */
Y2_IS_CHK_TXS2 = 1<<9, /* Descriptor error TXS 2 */
Y2_IS_CHK_TXA2 = 1<<8, /* Descriptor error TXA 2 */
+ Y2_IS_PSM_ACK = 1<<7, /* PSM Acknowledge (Yukon-Optima only) */
+ Y2_IS_PTP_TIST = 1<<6, /* PTP Time Stamp (Yukon-Optima only) */
+ Y2_IS_PHY_QLNK = 1<<5, /* PHY Quick Link (Yukon-Optima only) */
+
Y2_IS_IRQ_PHY1 = 1<<4, /* Interrupt from PHY 1 */
Y2_IS_IRQ_MAC1 = 1<<3, /* Interrupt from MAC 1 */
Y2_IS_CHK_RX1 = 1<<2, /* Descriptor error Rx 1 */
Y2_IS_CHK_TXS1 = 1<<1, /* Descriptor error TXS 1 */
Y2_IS_CHK_TXA1 = 1<<0, /* Descriptor error TXA 1 */
- Y2_IS_BASE = Y2_IS_HW_ERR | Y2_IS_STAT_BMU |
- Y2_IS_POLL_CHK | Y2_IS_TWSI_RDY |
- Y2_IS_IRQ_SW | Y2_IS_TIMINT,
- Y2_IS_PORT_1 = Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1 |
- Y2_IS_CHK_RX1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_TXS1,
- Y2_IS_PORT_2 = Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2 |
- Y2_IS_CHK_RX2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_TXS2,
+ Y2_IS_BASE = Y2_IS_HW_ERR | Y2_IS_STAT_BMU,
+ Y2_IS_PORT_1 = Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1
+ | Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1,
+ Y2_IS_PORT_2 = Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2
+ | Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2,
+ Y2_IS_ERROR = Y2_IS_HW_ERR |
+ Y2_IS_IRQ_MAC1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1 |
+ Y2_IS_IRQ_MAC2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2,
};
/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2,
Y2_HWE_ALL_MASK = Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT |
- Y2_IS_PCI_EXP |
Y2_HWE_L1_MASK | Y2_HWE_L2_MASK,
};
TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
};
+/* B2_GPIO */
+enum {
+ GLB_GPIO_CLK_DEB_ENA = 1<<31, /* Clock Debug Enable */
+ GLB_GPIO_CLK_DBG_MSK = 0xf<<26, /* Clock Debug */
+
+ GLB_GPIO_INT_RST_D3_DIS = 1<<15, /* Disable Internal Reset After D3 to D0 */
+ GLB_GPIO_LED_PAD_SPEED_UP = 1<<14, /* LED PAD Speed Up */
+ GLB_GPIO_STAT_RACE_DIS = 1<<13, /* Status Race Disable */
+ GLB_GPIO_TEST_SEL_MSK = 3<<11, /* Testmode Select */
+ GLB_GPIO_TEST_SEL_BASE = 1<<11,
+ GLB_GPIO_RAND_ENA = 1<<10, /* Random Enable */
+ GLB_GPIO_RAND_BIT_1 = 1<<9, /* Random Bit 1 */
+};
+
/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
enum {
CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */
/* B2_CHIP_ID 8 bit Chip Identification Number */
enum {
- CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */
- CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */
- CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
- CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */
- CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
- CHIP_ID_YUKON_EC_U = 0xb4, /* Chip ID for YUKON-2 EC Ultra */
- CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
- CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
+ CHIP_ID_YUKON_XL = 0xb3, /* YUKON-2 XL */
+ CHIP_ID_YUKON_EC_U = 0xb4, /* YUKON-2 EC Ultra */
+ CHIP_ID_YUKON_EX = 0xb5, /* YUKON-2 Extreme */
+ CHIP_ID_YUKON_EC = 0xb6, /* YUKON-2 EC */
+ CHIP_ID_YUKON_FE = 0xb7, /* YUKON-2 FE */
+ CHIP_ID_YUKON_FE_P = 0xb8, /* YUKON-2 FE+ */
+ CHIP_ID_YUKON_SUPR = 0xb9, /* YUKON-2 Supreme */
+ CHIP_ID_YUKON_UL_2 = 0xba, /* YUKON-2 Ultra 2 */
+ CHIP_ID_YUKON_OPT = 0xbc, /* YUKON-2 Optima */
+};
+enum yukon_xl_rev {
+ CHIP_REV_YU_XL_A0 = 0,
+ CHIP_REV_YU_XL_A1 = 1,
+ CHIP_REV_YU_XL_A2 = 2,
+ CHIP_REV_YU_XL_A3 = 3,
+};
+
+enum yukon_ec_rev {
CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */
CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */
CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */
};
+enum yukon_ec_u_rev {
+ CHIP_REV_YU_EC_U_A0 = 1,
+ CHIP_REV_YU_EC_U_A1 = 2,
+ CHIP_REV_YU_EC_U_B0 = 3,
+ CHIP_REV_YU_EC_U_B1 = 5,
+};
+enum yukon_fe_rev {
+ CHIP_REV_YU_FE_A1 = 1,
+ CHIP_REV_YU_FE_A2 = 2,
+};
+enum yukon_fe_p_rev {
+ CHIP_REV_YU_FE2_A0 = 0,
+};
+enum yukon_ex_rev {
+ CHIP_REV_YU_EX_A0 = 1,
+ CHIP_REV_YU_EX_B0 = 2,
+};
+enum yukon_supr_rev {
+ CHIP_REV_YU_SU_A0 = 0,
+ CHIP_REV_YU_SU_B0 = 1,
+ CHIP_REV_YU_SU_B1 = 3,
+};
+
/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */
enum {
TIM_T_STEP = 1<<0, /* Test step */
};
+/* Y2_PEX_PHY_ADDR/DATA PEX PHY address and data reg (Yukon-2 only) */
+enum {
+ PEX_RD_ACCESS = 1<<31, /* Access Mode Read = 1, Write = 0 */
+ PEX_DB_ACCESS = 1<<30, /* Access to debug register */
+};
+
/* B3_RAM_ADDR 32 bit RAM Address, to read or write */
/* Bit 31..19: reserved */
#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */
TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */
TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */
TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */
+
+ RSS_KEY = 0x0220, /* RSS Key setup */
+ RSS_CFG = 0x0248, /* RSS Configuration */
};
+enum {
+ HASH_TCP_IPV6_EX_CTRL = 1<<5,
+ HASH_IPV6_EX_CTRL = 1<<4,
+ HASH_TCP_IPV6_CTRL = 1<<3,
+ HASH_IPV6_CTRL = 1<<2,
+ HASH_TCP_IPV4_CTRL = 1<<1,
+ HASH_IPV4_CTRL = 1<<0,
+
+ HASH_ALL = 0x3f,
+};
enum {
B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */
enum {
B8_Q_REGS = 0x0400, /* base of Queue registers */
Q_D = 0x00, /* 8*32 bit Current Descriptor */
- Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */
- Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */
+ Q_VLAN = 0x20, /* 16 bit Current VLAN Tag */
+ Q_DONE = 0x24, /* 16 bit Done Index */
Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */
Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */
Q_BC = 0x30, /* 32 bit Current Byte Counter */
Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */
- Q_F = 0x38, /* 32 bit Flag Register */
- Q_T1 = 0x3c, /* 32 bit Test Register 1 */
- Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */
- Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */
- Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */
- Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */
- Q_T2 = 0x40, /* 32 bit Test Register 2 */
- Q_T3 = 0x44, /* 32 bit Test Register 3 */
+ Q_TEST = 0x38, /* 32 bit Test/Control Register */
/* Yukon-2 */
- Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */
Q_WM = 0x40, /* 16 bit FIFO Watermark */
Q_AL = 0x42, /* 8 bit FIFO Alignment */
Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */
};
#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
+/* Q_TEST 32 bit Test Register */
+enum {
+ /* Transmit */
+ F_TX_CHK_AUTO_OFF = 1<<31, /* Tx checksum auto calc off (Yukon EX) */
+ F_TX_CHK_AUTO_ON = 1<<30, /* Tx checksum auto calc off (Yukon EX) */
+
+ /* Receive */
+ F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */
+
+ /* Hardware testbits not used */
+};
/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
enum {
PHY_ADDR_MARV = 0,
};
-#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+#define RB_ADDR(offs, queue) ((u16) B16_RAM_REGS + (queue) + (offs))
enum {
RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
- RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
+ RX_GMF_FL_THR = 0x0c50,/* 16 bit Rx GMAC FIFO Flush Threshold */
+ RX_GMF_FL_CTRL = 0x0c52,/* 16 bit Rx GMAC FIFO Flush Control */
RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */
- RX_GMF_UP_THR = 0x0c58,/* 8 bit Rx Upper Pause Thr (Yukon-EC_U) */
- RX_GMF_LP_THR = 0x0c5a,/* 8 bit Rx Lower Pause Thr (Yukon-EC_U) */
+ RX_GMF_UP_THR = 0x0c58,/* 16 bit Rx Upper Pause Thr (Yukon-EC_U) */
+ RX_GMF_LP_THR = 0x0c5a,/* 16 bit Rx Lower Pause Thr (Yukon-EC_U) */
RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */
RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
BMU_FIFO_ENA | BMU_OP_ON,
BMU_WM_DEFAULT = 0x600,
+ BMU_WM_PEX = 0x80,
};
/* Tx BMU Control / Status Registers (Yukon-2) */
BMU_TX_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment length mismatch */
};
+/* TBMU_TEST 0x06B8 Transmit BMU Test Register */
+enum {
+ TBMU_TEST_BMU_TX_CHK_AUTO_OFF = 1<<31, /* BMU Tx Checksum Auto Calculation Disable */
+ TBMU_TEST_BMU_TX_CHK_AUTO_ON = 1<<30, /* BMU Tx Checksum Auto Calculation Enable */
+ TBMU_TEST_HOME_ADD_PAD_FIX1_EN = 1<<29, /* Home Address Paddiing FIX1 Enable */
+ TBMU_TEST_HOME_ADD_PAD_FIX1_DIS = 1<<28, /* Home Address Paddiing FIX1 Disable */
+ TBMU_TEST_ROUTING_ADD_FIX_EN = 1<<27, /* Routing Address Fix Enable */
+ TBMU_TEST_ROUTING_ADD_FIX_DIS = 1<<26, /* Routing Address Fix Disable */
+ TBMU_TEST_HOME_ADD_FIX_EN = 1<<25, /* Home address checksum fix enable */
+ TBMU_TEST_HOME_ADD_FIX_DIS = 1<<24, /* Home address checksum fix disable */
+
+ TBMU_TEST_TEST_RSPTR_ON = 1<<22, /* Testmode Shadow Read Ptr On */
+ TBMU_TEST_TEST_RSPTR_OFF = 1<<21, /* Testmode Shadow Read Ptr Off */
+ TBMU_TEST_TESTSTEP_RSPTR = 1<<20, /* Teststep Shadow Read Ptr */
+
+ TBMU_TEST_TEST_RPTR_ON = 1<<18, /* Testmode Read Ptr On */
+ TBMU_TEST_TEST_RPTR_OFF = 1<<17, /* Testmode Read Ptr Off */
+ TBMU_TEST_TESTSTEP_RPTR = 1<<16, /* Teststep Read Ptr */
+
+ TBMU_TEST_TEST_WSPTR_ON = 1<<14, /* Testmode Shadow Write Ptr On */
+ TBMU_TEST_TEST_WSPTR_OFF = 1<<13, /* Testmode Shadow Write Ptr Off */
+ TBMU_TEST_TESTSTEP_WSPTR = 1<<12, /* Teststep Shadow Write Ptr */
+
+ TBMU_TEST_TEST_WPTR_ON = 1<<10, /* Testmode Write Ptr On */
+ TBMU_TEST_TEST_WPTR_OFF = 1<<9, /* Testmode Write Ptr Off */
+ TBMU_TEST_TESTSTEP_WPTR = 1<<8, /* Teststep Write Ptr */
+
+ TBMU_TEST_TEST_REQ_NB_ON = 1<<6, /* Testmode Req Nbytes/Addr On */
+ TBMU_TEST_TEST_REQ_NB_OFF = 1<<5, /* Testmode Req Nbytes/Addr Off */
+ TBMU_TEST_TESTSTEP_REQ_NB = 1<<4, /* Teststep Req Nbytes/Addr */
+
+ TBMU_TEST_TEST_DONE_IDX_ON = 1<<2, /* Testmode Done Index On */
+ TBMU_TEST_TEST_DONE_IDX_OFF = 1<<1, /* Testmode Done Index Off */
+ TBMU_TEST_TESTSTEP_DONE_IDX = 1<<0, /* Teststep Done Index */
+};
+
/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
/* PREF_UNIT_CTRL 32 bit Prefetch Control register */
enum {
TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */
TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */
TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */
+
+ /* Threshold values for Yukon-EC Ultra and Extreme */
+ ECU_AE_THR = 0x0070, /* Almost Empty Threshold */
+ ECU_TXFF_LEV = 0x01a0, /* Tx BMU FIFO Level */
+ ECU_JUMBO_WM = 0x0080, /* Jumbo Mode Watermark */
};
/* Descriptor Poll Timer Registers */
POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit Poll. List Start Addr (high) */
};
+enum {
+ SMB_CFG = 0x0e40, /* 32 bit SMBus Config Register */
+ SMB_CSR = 0x0e44, /* 32 bit SMBus Control/Status Register */
+};
+
+enum {
+ CPU_WDOG = 0x0e48, /* 32 bit Watchdog Register */
+ CPU_CNTR = 0x0e4C, /* 32 bit Counter Register */
+ CPU_TIM = 0x0e50,/* 32 bit Timer Compare Register */
+ CPU_AHB_ADDR = 0x0e54, /* 32 bit CPU AHB Debug Register */
+ CPU_AHB_WDATA = 0x0e58, /* 32 bit CPU AHB Debug Register */
+ CPU_AHB_RDATA = 0x0e5C, /* 32 bit CPU AHB Debug Register */
+ HCU_MAP_BASE = 0x0e60, /* 32 bit Reset Mapping Base */
+ CPU_AHB_CTRL = 0x0e64, /* 32 bit CPU AHB Debug Register */
+ HCU_CCSR = 0x0e68, /* 32 bit CPU Control and Status Register */
+ HCU_HCSR = 0x0e6C, /* 32 bit Host Control and Status Register */
+};
+
/* ASF Subsystem Registers (Yukon-2 only) */
enum {
B28_Y2_SMB_CONFIG = 0x0e40,/* 32 bit ASF SMBus Config Register */
GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */
/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
-
- WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */
-
WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */
WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
- WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */
- WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */
WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
/* WOL Pattern Length Registers (YUKON only) */
-
WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
/* WOL Pattern Counter Registers (YUKON only) */
-
-
WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
};
+#define WOL_REGS(port, x) (x + (port)*0x80)
enum {
WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
};
+#define WOL_PATT_RAM_BASE(port) (WOL_PATT_RAM_1 + (port)*0x400)
enum {
BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */
PHY_BCOM_ID1_C0 = 0x6044,
PHY_BCOM_ID1_C5 = 0x6047,
- PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
+ PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
- PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
- PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
+ PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
+ PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
+ PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE (PHY 88E3082 Rev.A1) */
+ PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU (PHY 88E1149 Rev.B2?) */
};
/* Advertisement register bits */
PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
};
-#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
+#define PHY_M_PC_MDI_XMODE(x) (((u16)(x)<<5) & PHY_M_PC_MDIX_MSK)
enum {
PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
};
+/* for Yukon-EC Ultra Gigabit Ethernet PHY (88E1149 only) */
+enum {
+ PHY_M_PC_COP_TX_DIS = 1<<3, /* Copper Transmitter Disable */
+ PHY_M_PC_POW_D_ENA = 1<<2, /* Power Down Enable */
+};
+
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
PHY_M_IS_JABBER = 1<<0, /* Jabber */
PHY_M_DEF_MSK = PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE
- | PHY_M_IS_FIFO_ERROR,
+ | PHY_M_IS_DUP_CHANGE,
PHY_M_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL,
};
PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
-#define PHY_M_EC_M_DSC(x) ((x)<<10 & PHY_M_EC_M_DSC_MSK)
+#define PHY_M_EC_M_DSC(x) ((u16)(x)<<10 & PHY_M_EC_M_DSC_MSK)
/* 00=1x; 01=2x; 10=3x; 11=4x */
-#define PHY_M_EC_S_DSC(x) ((x)<<8 & PHY_M_EC_S_DSC_MSK)
+#define PHY_M_EC_S_DSC(x) ((u16)(x)<<8 & PHY_M_EC_S_DSC_MSK)
/* 00=dis; 01=1x; 10=2x; 11=3x */
-#define PHY_M_EC_DSC_2(x) ((x)<<9 & PHY_M_EC_M_DSC_MSK2)
+#define PHY_M_EC_DSC_2(x) ((u16)(x)<<9 & PHY_M_EC_M_DSC_MSK2)
/* 000=1x; 001=2x; 010=3x; 011=4x */
-#define PHY_M_EC_MAC_S(x) ((x)<<4 & PHY_M_EC_MAC_S_MSK)
+#define PHY_M_EC_MAC_S(x) ((u16)(x)<<4 & PHY_M_EC_MAC_S_MSK)
/* 01X=0; 110=2.5; 111=25 (MHz) */
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
};
/* !!! Errata in spec. (1 = disable) */
-#define PHY_M_PC_DSC(x) (((x)<<12) & PHY_M_PC_DSC_MSK)
+#define PHY_M_PC_DSC(x) (((u16)(x)<<12) & PHY_M_PC_DSC_MSK)
/* 100=5x; 101=6x; 110=7x; 111=8x */
enum {
MAC_TX_CLK_0_MHZ = 2,
PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
};
-#define PHY_M_LED_PULS_DUR(x) (((x)<<12) & PHY_M_LEDC_PULS_MSK)
+#define PHY_M_LED_PULS_DUR(x) (((u16)(x)<<12) & PHY_M_LEDC_PULS_MSK)
/***** PHY_MARV_PHY_STAT (page 3)16 bit r/w Polarity Control Reg. *****/
enum {
PULS_1300MS = 7,/* 1.3 s to 2.7 s */
};
-#define PHY_M_LED_BLINK_RT(x) (((x)<<8) & PHY_M_LEDC_BL_R_MSK)
+#define PHY_M_LED_BLINK_RT(x) (((u16)(x)<<8) & PHY_M_LEDC_BL_R_MSK)
enum {
BLINK_42MS = 0,/* 42 ms */
};
/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
-#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
- /* Bit 13..12: reserved */
-#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
-#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
-#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
-#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
-#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
-#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
+#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
-enum {
- MO_LED_NORM = 0,
- MO_LED_BLINK = 1,
- MO_LED_OFF = 2,
- MO_LED_ON = 3,
+#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
+#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
+#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
+#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
+#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
+#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
+
+enum led_mode {
+ MO_LED_NORM = 0,
+ MO_LED_BLINK = 1,
+ MO_LED_OFF = 2,
+ MO_LED_ON = 3,
};
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
};
-#define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
-#define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
-#define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
+#define PHY_M_FELP_LED2_CTRL(x) (((u16)(x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x) (((u16)(x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x) (((u16)(x)<<0) & PHY_M_FELP_LED0_MSK)
enum {
LED_PAR_CTRL_COLX = 0x00,
};
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
+/***** PHY_MARV_PHY_CTRL (page 1) 16 bit r/w Fiber Specific Ctrl *****/
+enum {
+ PHY_M_FIB_FORCE_LNK = 1<<10,/* Force Link Good */
+ PHY_M_FIB_SIGD_POL = 1<<9, /* SIGDET Polarity */
+ PHY_M_FIB_TX_DIS = 1<<3, /* Transmitter Disable */
+};
+
+/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
enum {
PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
+ PHY_M_MAC_GMIF_PUP = 1<<3, /* GMII Power Up (88E1149 only) */
PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
PHY_M_MAC_MD_COPPER = 5,/* Copper only */
PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */
GM_SMI_CTRL = 0x0080, /* 16 bit r/w SMI Control Register */
GM_SMI_DATA = 0x0084, /* 16 bit r/w SMI Data Register */
GM_PHY_ADDR = 0x0088, /* 16 bit r/w GPHY Address Register */
+/* MIB Counters */
+ GM_MIB_CNT_BASE = 0x0100, /* Base Address of MIB Counters */
+ GM_MIB_CNT_END = 0x025C, /* Last MIB counter */
};
-/* MIB Counters */
-#define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */
-#define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */
/*
* MIB Counters base address definitions (low word) -
* use offset 4 for access to high word (32 bit r/o)
*/
enum {
- GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */
+ GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */
GM_RXF_BC_OK = GM_MIB_CNT_BASE + 8, /* Broadcast Frames Received OK */
GM_RXF_MPAUSE = GM_MIB_CNT_BASE + 16, /* Pause MAC Ctrl Frames Received */
GM_RXF_MC_OK = GM_MIB_CNT_BASE + 24, /* Multicast Frames Received OK */
GM_RXF_FCS_ERR = GM_MIB_CNT_BASE + 32, /* Rx Frame Check Seq. Error */
- /* GM_MIB_CNT_BASE + 40: reserved */
+
GM_RXO_OK_LO = GM_MIB_CNT_BASE + 48, /* Octets Received OK Low */
GM_RXO_OK_HI = GM_MIB_CNT_BASE + 56, /* Octets Received OK High */
GM_RXO_ERR_LO = GM_MIB_CNT_BASE + 64, /* Octets Received Invalid Low */
GM_RXF_SHT = GM_MIB_CNT_BASE + 80, /* Frames <64 Byte Received OK */
GM_RXE_FRAG = GM_MIB_CNT_BASE + 88, /* Frames <64 Byte Received with FCS Err */
GM_RXF_64B = GM_MIB_CNT_BASE + 96, /* 64 Byte Rx Frame */
- GM_RXF_127B = GM_MIB_CNT_BASE + 104, /* 65-127 Byte Rx Frame */
- GM_RXF_255B = GM_MIB_CNT_BASE + 112, /* 128-255 Byte Rx Frame */
- GM_RXF_511B = GM_MIB_CNT_BASE + 120, /* 256-511 Byte Rx Frame */
- GM_RXF_1023B = GM_MIB_CNT_BASE + 128, /* 512-1023 Byte Rx Frame */
- GM_RXF_1518B = GM_MIB_CNT_BASE + 136, /* 1024-1518 Byte Rx Frame */
- GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144, /* 1519-MaxSize Byte Rx Frame */
- GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152, /* Rx Frame too Long Error */
- GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160, /* Rx Jabber Packet Frame */
- /* GM_MIB_CNT_BASE + 168: reserved */
- GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176, /* Rx FIFO overflow Event */
- /* GM_MIB_CNT_BASE + 184: reserved */
- GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192, /* Unicast Frames Xmitted OK */
- GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200, /* Broadcast Frames Xmitted OK */
- GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208, /* Pause MAC Ctrl Frames Xmitted */
- GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216, /* Multicast Frames Xmitted OK */
- GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224, /* Octets Transmitted OK Low */
- GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232, /* Octets Transmitted OK High */
- GM_TXF_64B = GM_MIB_CNT_BASE + 240, /* 64 Byte Tx Frame */
- GM_TXF_127B = GM_MIB_CNT_BASE + 248, /* 65-127 Byte Tx Frame */
- GM_TXF_255B = GM_MIB_CNT_BASE + 256, /* 128-255 Byte Tx Frame */
- GM_TXF_511B = GM_MIB_CNT_BASE + 264, /* 256-511 Byte Tx Frame */
- GM_TXF_1023B = GM_MIB_CNT_BASE + 272, /* 512-1023 Byte Tx Frame */
- GM_TXF_1518B = GM_MIB_CNT_BASE + 280, /* 1024-1518 Byte Tx Frame */
- GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288, /* 1519-MaxSize Byte Tx Frame */
-
- GM_TXF_COL = GM_MIB_CNT_BASE + 304, /* Tx Collision */
- GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312, /* Tx Late Collision */
- GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320, /* Tx aborted due to Exces. Col. */
- GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328, /* Tx Multiple Collision */
- GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336, /* Tx Single Collision */
- GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344, /* Tx FIFO Underrun Event */
+ GM_RXF_127B = GM_MIB_CNT_BASE + 104,/* 65-127 Byte Rx Frame */
+ GM_RXF_255B = GM_MIB_CNT_BASE + 112,/* 128-255 Byte Rx Frame */
+ GM_RXF_511B = GM_MIB_CNT_BASE + 120,/* 256-511 Byte Rx Frame */
+ GM_RXF_1023B = GM_MIB_CNT_BASE + 128,/* 512-1023 Byte Rx Frame */
+ GM_RXF_1518B = GM_MIB_CNT_BASE + 136,/* 1024-1518 Byte Rx Frame */
+ GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144,/* 1519-MaxSize Byte Rx Frame */
+ GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152,/* Rx Frame too Long Error */
+ GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160,/* Rx Jabber Packet Frame */
+
+ GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176,/* Rx FIFO overflow Event */
+ GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192,/* Unicast Frames Xmitted OK */
+ GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200,/* Broadcast Frames Xmitted OK */
+ GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208,/* Pause MAC Ctrl Frames Xmitted */
+ GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216,/* Multicast Frames Xmitted OK */
+ GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224,/* Octets Transmitted OK Low */
+ GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232,/* Octets Transmitted OK High */
+ GM_TXF_64B = GM_MIB_CNT_BASE + 240,/* 64 Byte Tx Frame */
+ GM_TXF_127B = GM_MIB_CNT_BASE + 248,/* 65-127 Byte Tx Frame */
+ GM_TXF_255B = GM_MIB_CNT_BASE + 256,/* 128-255 Byte Tx Frame */
+ GM_TXF_511B = GM_MIB_CNT_BASE + 264,/* 256-511 Byte Tx Frame */
+ GM_TXF_1023B = GM_MIB_CNT_BASE + 272,/* 512-1023 Byte Tx Frame */
+ GM_TXF_1518B = GM_MIB_CNT_BASE + 280,/* 1024-1518 Byte Tx Frame */
+ GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288,/* 1519-MaxSize Byte Tx Frame */
+
+ GM_TXF_COL = GM_MIB_CNT_BASE + 304,/* Tx Collision */
+ GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312,/* Tx Late Collision */
+ GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320,/* Tx aborted due to Exces. Col. */
+ GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328,/* Tx Multiple Collision */
+ GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336,/* Tx Single Collision */
+ GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344,/* Tx FIFO Underrun Event */
};
/* GMAC Bit Definitions */
};
#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
-#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
enum {
GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */
GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */
GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */
- GM_TXCR_COL_THR_MSK = 1<<10, /* Bit 12..10: Collision Threshold */
+ GM_TXCR_COL_THR_MSK = 7<<10, /* Bit 12..10: Collision Threshold */
};
#define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK)
/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
enum {
GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
- GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */
- GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
- GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
- GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
+ GM_SMOD_LIMIT_4 = 1<<10, /* 4 consecutive Tx trials */
+ GM_SMOD_VLAN_ENA = 1<<9, /* Enable VLAN (Max. Frame Len) */
+ GM_SMOD_JUMBO_ENA = 1<<8, /* Enable Jumbo (Max. Frame Len) */
+
+ GM_NEW_FLOW_CTRL = 1<<6, /* Enable New Flow-Control */
+
+ GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
};
#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
};
-#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
-#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
+#define GM_SMI_CT_PHY_AD(x) (((u16)(x)<<11) & GM_SMI_CT_PHY_A_MSK)
+#define GM_SMI_CT_REG_AD(x) (((u16)(x)<<6) & GM_SMI_CT_REG_A_MSK)
/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
enum {
/* Receive Frame Status Encoding */
enum {
- GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
+ GMR_FS_LEN = 0x7fff<<16, /* Bit 30..16: Rx Frame Length */
GMR_FS_VLAN = 1<<13, /* VLAN Packet */
GMR_FS_JABBER = 1<<12, /* Jabber Packet */
GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */
GMR_FS_ANY_ERR = GMR_FS_RX_FF_OV | GMR_FS_CRC_ERR |
GMR_FS_FRAGMENT | GMR_FS_LONG_ERR |
- GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC |
+ GMR_FS_MII_ERR | GMR_FS_BAD_FC |
GMR_FS_UN_SIZE | GMR_FS_JABBER,
};
/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
enum {
+ RX_GCLKMAC_ENA = 1<<31, /* RX MAC Clock Gating Enable */
+ RX_GCLKMAC_OFF = 1<<30,
+
+ RX_STFW_DIS = 1<<29, /* RX Store and Forward Enable */
+ RX_STFW_ENA = 1<<28,
+
RX_TRUNC_ON = 1<<27, /* enable packet truncation */
RX_TRUNC_OFF = 1<<26, /* disable packet truncation */
RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */
RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */
+ RX_MACSEC_FLUSH_ON = 1<<23,
+ RX_MACSEC_FLUSH_OFF = 1<<22,
+ RX_MACSEC_ASF_FLUSH_ON = 1<<21,
+ RX_MACSEC_ASF_FLUSH_OFF = 1<<20,
+
+ GMF_RX_OVER_ON = 1<<19, /* enable flushing on receive overrun */
+ GMF_RX_OVER_OFF = 1<<18, /* disable flushing on receive overrun */
+ GMF_ASF_RX_OVER_ON = 1<<17, /* enable flushing of ASF when overrun */
+ GMF_ASF_RX_OVER_OFF = 1<<16, /* disable flushing of ASF when overrun */
+
GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */
GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */
GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */
GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON,
};
+/* RX_GMF_FL_CTRL 16 bit Rx GMAC FIFO Flush Control (Yukon-Supreme) */
+enum {
+ RX_IPV6_SA_MOB_ENA = 1<<9, /* IPv6 SA Mobility Support Enable */
+ RX_IPV6_SA_MOB_DIS = 1<<8, /* IPv6 SA Mobility Support Disable */
+ RX_IPV6_DA_MOB_ENA = 1<<7, /* IPv6 DA Mobility Support Enable */
+ RX_IPV6_DA_MOB_DIS = 1<<6, /* IPv6 DA Mobility Support Disable */
+ RX_PTR_SYNCDLY_ENA = 1<<5, /* Pointers Delay Synch Enable */
+ RX_PTR_SYNCDLY_DIS = 1<<4, /* Pointers Delay Synch Disable */
+ RX_ASF_NEWFLAG_ENA = 1<<3, /* RX ASF Flag New Logic Enable */
+ RX_ASF_NEWFLAG_DIS = 1<<2, /* RX ASF Flag New Logic Disable */
+ RX_FLSH_MISSPKT_ENA = 1<<1, /* RX Flush Miss-Packet Enable */
+ RX_FLSH_MISSPKT_DIS = 1<<0, /* RX Flush Miss-Packet Disable */
+};
+
+/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */
+enum {
+ TX_DYN_WM_ENA = 3, /* Yukon-FE+ specific */
+};
/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
enum {
- TX_STFW_DIS = 1<<31,/* Disable Store & Forward (Yukon-EC Ultra) */
- TX_STFW_ENA = 1<<30,/* Enable Store & Forward (Yukon-EC Ultra) */
+ TX_STFW_DIS = 1<<31,/* Disable Store & Forward */
+ TX_STFW_ENA = 1<<30,/* Enable Store & Forward */
TX_VLAN_TAG_ON = 1<<25,/* enable VLAN tagging */
TX_VLAN_TAG_OFF = 1<<24,/* disable VLAN tagging */
+ TX_PCI_JUM_ENA = 1<<23,/* PCI Jumbo Mode enable */
+ TX_PCI_JUM_DIS = 1<<22,/* PCI Jumbo Mode enable */
+
GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */
Y2_ASF_CLR_ASFI = 1<<1, /* Clear host IRQ */
Y2_ASF_HOST_IRQ = 1<<0, /* Issue an IRQ to HOST system */
};
+/* HCU_CCSR CPU Control and Status Register */
+enum {
+ HCU_CCSR_SMBALERT_MONITOR= 1<<27, /* SMBALERT pin monitor */
+ HCU_CCSR_CPU_SLEEP = 1<<26, /* CPU sleep status */
+ /* Clock Stretching Timeout */
+ HCU_CCSR_CS_TO = 1<<25,
+ HCU_CCSR_WDOG = 1<<24, /* Watchdog Reset */
+
+ HCU_CCSR_CLR_IRQ_HOST = 1<<17, /* Clear IRQ_HOST */
+ HCU_CCSR_SET_IRQ_HCU = 1<<16, /* Set IRQ_HCU */
+
+ HCU_CCSR_AHB_RST = 1<<9, /* Reset AHB bridge */
+ HCU_CCSR_CPU_RST_MODE = 1<<8, /* CPU Reset Mode */
+
+ HCU_CCSR_SET_SYNC_CPU = 1<<5,
+ HCU_CCSR_CPU_CLK_DIVIDE_MSK = 3<<3,/* CPU Clock Divide */
+ HCU_CCSR_CPU_CLK_DIVIDE_BASE= 1<<3,
+ HCU_CCSR_OS_PRSNT = 1<<2, /* ASF OS Present */
+/* Microcontroller State */
+ HCU_CCSR_UC_STATE_MSK = 3,
+ HCU_CCSR_UC_STATE_BASE = 1<<0,
+ HCU_CCSR_ASF_RESET = 0,
+ HCU_CCSR_ASF_HALTED = 1<<1,
+ HCU_CCSR_ASF_RUNNING = 1<<0,
+};
+
+/* HCU_HCSR Host Control and Status Register */
+enum {
+ HCU_HCSR_SET_IRQ_CPU = 1<<16, /* Set IRQ_CPU */
+
+ HCU_HCSR_CLR_IRQ_HCU = 1<<1, /* Clear IRQ_HCU */
+ HCU_HCSR_SET_IRQ_HOST = 1<<0, /* Set IRQ_HOST */
+};
/* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */
enum {
/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
enum {
+ GMC_SET_RST = 1<<15,/* MAC SEC RST */
+ GMC_SEC_RST_OFF = 1<<14,/* MAC SEC RSt OFF */
+ GMC_BYP_MACSECRX_ON = 1<<13,/* Bypass macsec RX */
+ GMC_BYP_MACSECRX_OFF= 1<<12,/* Bypass macsec RX off */
+ GMC_BYP_MACSECTX_ON = 1<<11,/* Bypass macsec TX */
+ GMC_BYP_MACSECTX_OFF= 1<<10,/* Bypass macsec TX off*/
+ GMC_BYP_RETR_ON = 1<<9, /* Bypass retransmit FIFO On */
+ GMC_BYP_RETR_OFF= 1<<8, /* Bypass retransmit FIFO Off */
+
GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */
GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */
GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */
/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
enum {
- GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
- GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */
- GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */
- GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */
- GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */
- GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */
- GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */
- GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */
- GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */
- GPC_ANEG_0 = 1<<19, /* ANEG[0] */
- GPC_ENA_XC = 1<<18, /* Enable MDI crossover */
- GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */
- GPC_ANEG_3 = 1<<16, /* ANEG[3] */
- GPC_ANEG_2 = 1<<15, /* ANEG[2] */
- GPC_ANEG_1 = 1<<14, /* ANEG[1] */
- GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */
- GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */
- GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */
- GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */
- GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */
- GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */
- /* Bits 7..2: reserved */
+ GPC_TX_PAUSE = 1<<30, /* Tx pause enabled (ro) */
+ GPC_RX_PAUSE = 1<<29, /* Rx pause enabled (ro) */
+ GPC_SPEED = 3<<27, /* PHY speed (ro) */
+ GPC_LINK = 1<<26, /* Link up (ro) */
+ GPC_DUPLEX = 1<<25, /* Duplex (ro) */
+ GPC_CLOCK = 1<<24, /* 125Mhz clock stable (ro) */
+
+ GPC_PDOWN = 1<<23, /* Internal regulator 2.5 power down */
+ GPC_TSTMODE = 1<<22, /* Test mode */
+ GPC_REG18 = 1<<21, /* Reg18 Power down */
+ GPC_REG12SEL = 3<<19, /* Reg12 power setting */
+ GPC_REG18SEL = 3<<17, /* Reg18 power setting */
+ GPC_SPILOCK = 1<<16, /* SPI lock (ASF) */
+
+ GPC_LEDMUX = 3<<14, /* LED Mux */
+ GPC_INTPOL = 1<<13, /* Interrupt polarity */
+ GPC_DETECT = 1<<12, /* Energy detect */
+ GPC_1000HD = 1<<11, /* Enable 1000Mbit HD */
+ GPC_SLAVE = 1<<10, /* Slave mode */
+ GPC_PAUSE = 1<<9, /* Pause enable */
+ GPC_LEDCTL = 3<<6, /* GPHY Leds */
+
GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */
GPC_RST_SET = 1<<0, /* Set GPHY Reset */
};
GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
#define GMAC_DEF_MSK GM_IS_TX_FF_UR
+};
/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
- /* Bits 15.. 2: reserved */
+enum { /* Bits 15.. 2: reserved */
GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */
GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */
+};
/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
+enum {
WOL_CTL_LINK_CHG_OCC = 1<<15,
WOL_CTL_MAGIC_PKT_OCC = 1<<14,
WOL_CTL_PATTERN_OCC = 1<<13,
WOL_CTL_DIS_PATTERN_UNIT = 1<<0,
};
-#define WOL_CTL_DEFAULT \
- (WOL_CTL_DIS_PME_ON_LINK_CHG | \
- WOL_CTL_DIS_PME_ON_PATTERN | \
- WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
- WOL_CTL_DIS_LINK_CHG_UNIT | \
- WOL_CTL_DIS_PATTERN_UNIT | \
- WOL_CTL_DIS_MAGIC_PKT_UNIT)
-
-/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
-#define WOL_CTL_PATT_ENA(x) (1 << (x))
-
/* Control flags */
enum {
INIT_SUM= 1<<3,
LOCK_SUM= 1<<4,
INS_VLAN= 1<<5,
- FRC_STAT= 1<<6,
EOP = 1<<7,
};
OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN,
OP_LRGLEN = 0x24,
OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN,
+ OP_MSS = 0x28,
+ OP_MSSVLAN = OP_MSS | OP_VLAN,
+
OP_BUFFER = 0x40,
OP_PACKET = 0x41,
OP_LARGESEND = 0x43,
+ OP_LSOV2 = 0x45,
/* YUKON-2 STATUS opcodes defines */
OP_RXSTAT = 0x60,
OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN,
OP_RSS_HASH = 0x65,
OP_TXINDEXLE = 0x68,
+ OP_MACSEC = 0x6c,
+ OP_PUTIDX = 0x70,
};
-/* Yukon 2 hardware interface
- * Not tested on big endian
- */
+enum status_css {
+ CSS_TCPUDPCSOK = 1<<7, /* TCP / UDP checksum is ok */
+ CSS_ISUDP = 1<<6, /* packet is a UDP packet */
+ CSS_ISTCP = 1<<5, /* packet is a TCP packet */
+ CSS_ISIPFRAG = 1<<4, /* packet is a TCP/UDP frag, CS calc not done */
+ CSS_ISIPV6 = 1<<3, /* packet is a IPv6 packet */
+ CSS_IPV4CSUMOK = 1<<2, /* IP v4: TCP header checksum is ok */
+ CSS_ISIPV4 = 1<<1, /* packet is a IPv4 packet */
+ CSS_LINK_BIT = 1<<0, /* port number (legacy) */
+};
+
+/* Yukon 2 hardware interface */
struct sky2_tx_le {
- union {
- __le32 addr;
- struct {
- __le16 offset;
- __le16 start;
- } csum __attribute((packed));
- struct {
- __le16 size;
- __le16 rsvd;
- } tso __attribute((packed));
- } tx;
+ __le32 addr;
__le16 length; /* also vlan tag or checksum start */
u8 ctrl;
u8 opcode;
__le16 length;
u8 ctrl;
u8 opcode;
-} __attribute((packed));;
+} __attribute((packed));
struct sky2_status_le {
__le32 status; /* also checksum */
__le16 length; /* also vlan tag */
- u8 link;
+ u8 css;
u8 opcode;
} __attribute((packed));
struct tx_ring_info {
struct sk_buff *skb;
- DECLARE_PCI_UNMAP_ADDR(mapaddr);
- u16 idx;
+ unsigned long flags;
+#define TX_MAP_SINGLE 0x0001
+#define TX_MAP_PAGE 0x0002
+ DEFINE_DMA_UNMAP_ADDR(mapaddr);
+ DEFINE_DMA_UNMAP_LEN(maplen);
};
-struct ring_info {
+struct rx_ring_info {
struct sk_buff *skb;
- dma_addr_t mapaddr;
+ dma_addr_t data_addr;
+ DEFINE_DMA_UNMAP_LEN(data_size);
+ dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
+};
+
+enum flow_control {
+ FC_NONE = 0,
+ FC_TX = 1,
+ FC_RX = 2,
+ FC_BOTH = 3,
};
struct sky2_port {
struct net_device *netdev;
unsigned port;
u32 msg_enable;
+ spinlock_t phy_lock;
- spinlock_t tx_lock ____cacheline_aligned_in_smp;
struct tx_ring_info *tx_ring;
struct sky2_tx_le *tx_le;
+ u16 tx_ring_size;
u16 tx_cons; /* next le to check */
u16 tx_prod; /* next le to use */
- u32 tx_addr64;
+ u16 tx_next; /* debug only */
+
u16 tx_pending;
- u16 tx_last_put;
u16 tx_last_mss;
+ u32 tx_last_upper;
+ u32 tx_tcpsum;
- struct ring_info *rx_ring ____cacheline_aligned_in_smp;
+ struct rx_ring_info *rx_ring ____cacheline_aligned_in_smp;
struct sky2_rx_le *rx_le;
- u32 rx_addr64;
+
u16 rx_next; /* next re to check */
u16 rx_put; /* next le index to use */
u16 rx_pending;
- u16 rx_last_put;
- u16 rx_bufsize;
+ u16 rx_data_size;
+ u16 rx_nfrags;
+
#ifdef SKY2_VLAN_TAG_USED
u16 rx_tag;
struct vlan_group *vlgrp;
#endif
+ struct {
+ unsigned long last;
+ u32 mac_rp;
+ u8 mac_lev;
+ u8 fifo_rp;
+ u8 fifo_lev;
+ } check;
dma_addr_t rx_le_map;
dma_addr_t tx_le_map;
- u32 advertising; /* ADVERTISED_ bits */
- u16 speed; /* SPEED_1000, SPEED_100, ... */
- u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
- u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
- u8 rx_pause;
- u8 tx_pause;
- u8 rx_csum;
- u8 wol;
- struct net_device_stats net_stats;
+ u16 advertising; /* ADVERTISED_ bits */
+ u16 speed; /* SPEED_1000, SPEED_100, ... */
+ u8 wol; /* WAKE_ bits */
+ u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
+ u16 flags;
+#define SKY2_FLAG_RX_CHECKSUM 0x0001
+#define SKY2_FLAG_AUTO_SPEED 0x0002
+#define SKY2_FLAG_AUTO_PAUSE 0x0004
- struct work_struct phy_task;
- struct semaphore phy_sema;
+ enum flow_control flow_mode;
+ enum flow_control flow_status;
+
+#ifdef CONFIG_SKY2_DEBUG
+ struct dentry *debugfs;
+#endif
};
struct sky2_hw {
void __iomem *regs;
struct pci_dev *pdev;
- u32 intr_mask;
+ struct napi_struct napi;
struct net_device *dev[2];
+ unsigned long flags;
+#define SKY2_HW_USE_MSI 0x00000001
+#define SKY2_HW_FIBRE_PHY 0x00000002
+#define SKY2_HW_GIGABIT 0x00000004
+#define SKY2_HW_NEWER_PHY 0x00000008
+#define SKY2_HW_RAM_BUFFER 0x00000010
+#define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */
+#define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */
+#define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */
+#define SKY2_HW_RSS_BROKEN 0x00000100
- int pm_cap;
- int msi;
u8 chip_id;
u8 chip_rev;
- u8 copper;
+ u8 pmd_type;
u8 ports;
struct sky2_status_le *st_le;
+ u32 st_size;
u32 st_idx;
dma_addr_t st_dma;
+
+ struct timer_list watchdog_timer;
+ struct work_struct restart_work;
+ wait_queue_head_t msi_wait;
+
+ char irq_name[0];
};
+static inline int sky2_is_copper(const struct sky2_hw *hw)
+{
+ return !(hw->flags & SKY2_HW_FIBRE_PHY);
+}
+
/* Register accessor for memory mapped device */
static inline u32 sky2_read32(const struct sky2_hw *hw, unsigned reg)
{
gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8));
gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8));
}
+
+/* PCI config space access */
+static inline u32 sky2_pci_read32(const struct sky2_hw *hw, unsigned reg)
+{
+ return sky2_read32(hw, Y2_CFG_SPC + reg);
+}
+
+static inline u16 sky2_pci_read16(const struct sky2_hw *hw, unsigned reg)
+{
+ return sky2_read16(hw, Y2_CFG_SPC + reg);
+}
+
+static inline void sky2_pci_write32(struct sky2_hw *hw, unsigned reg, u32 val)
+{
+ sky2_write32(hw, Y2_CFG_SPC + reg, val);
+}
+
+static inline void sky2_pci_write16(struct sky2_hw *hw, unsigned reg, u16 val)
+{
+ sky2_write16(hw, Y2_CFG_SPC + reg, val);
+}
#endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff