ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
/* downshift on PHY 88E1112 and 88E1149 is changed */
- if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED)
- && (hw->flags & SKY2_HW_NEWER_PHY)) {
+ if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) &&
+ (hw->flags & SKY2_HW_NEWER_PHY)) {
/* set downshift counter to 3x and enable downshift */
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
/* no effect on Yukon-XL */
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
- if ( !(sky2->flags & SKY2_FLAG_AUTO_SPEED)
- || sky2->speed == SPEED_100) {
+ if (!(sky2->flags & SKY2_FLAG_AUTO_SPEED) ||
+ sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
ledover |= PHY_M_LED_MO_100(MO_LED_ON);
}
{
u32 reg1;
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
reg1 &= ~phy_power[port];
reg1 |= coma_mode[port];
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
sky2_pci_read32(hw, PCI_DEV_REG1);
if (hw->chip_id == CHIP_ID_YUKON_FE)
gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_PDOWN);
}
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
reg1 |= phy_power[port]; /* set PHY to PowerDown/COMA Mode */
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
/* Force a renegotiation */
/* On chips without ram buffer, pause is controled by MAC level */
if (!(hw->flags & SKY2_HW_RAM_BUFFER)) {
/* Pause threshold is scaled by 8 in bytes */
- if (hw->chip_id == CHIP_ID_YUKON_FE_P
- && hw->chip_rev == CHIP_REV_YU_FE2_A0)
+ if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
+ hw->chip_rev == CHIP_REV_YU_FE2_A0)
reg = 1568 / 8;
else
reg = 1024 / 8;
/* These chips have no ram buffer?
* MAC Rx RAM Read is controlled by hardware */
if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
- (hw->chip_rev == CHIP_REV_YU_EC_U_A1
- || hw->chip_rev == CHIP_REV_YU_EC_U_B0))
+ (hw->chip_rev == CHIP_REV_YU_EC_U_A1 ||
+ hw->chip_rev == CHIP_REV_YU_EC_U_B0))
sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS);
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF);
/* Set almost empty threshold */
- if (hw->chip_id == CHIP_ID_YUKON_EC_U
- && hw->chip_rev == CHIP_REV_YU_EC_U_A0)
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
+ hw->chip_rev == CHIP_REV_YU_EC_U_A0)
sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
sky2->tx_cons = idx;
smp_mb();
- if (tx_avail(sky2) > MAX_SKB_TX_LE + 4)
+ /* Wake unless it's detached, and called e.g. from sky2_down() */
+ if (tx_avail(sky2) > MAX_SKB_TX_LE + 4 && netif_device_present(dev))
netif_wake_queue(dev);
}
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* Workaround shared GMAC reset */
- if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
- && port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
+ if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 &&
+ port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
netif_carrier_off(sky2->netdev);
- /* Turn on link LED */
+ /* Turn off link LED */
sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
if (netif_msg_link(sky2))
sky2->flow_status = FC_TX;
}
- if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
- && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
+ if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000 &&
+ !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
sky2->flow_status = FC_NONE;
if (sky2->flow_status & FC_TX)
if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
u16 pci_err;
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_err = sky2_pci_read16(hw, PCI_STATUS);
if (net_ratelimit())
dev_err(&pdev->dev, "PCI hardware error (0x%x)\n",
sky2_pci_write16(hw, PCI_STATUS,
pci_err | PCI_STATUS_ERROR_BITS);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
if (status & Y2_IS_PCI_EXP) {
/* PCI-Express uncorrectable Error occurred */
u32 err;
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
err = sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS);
sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS,
0xfffffffful);
dev_err(&pdev->dev, "PCI Express error (0x%x)\n", err);
sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
if (status & Y2_HWE_L1_MASK)
break;
case CHIP_ID_YUKON_UL_2:
+ hw->flags = SKY2_HW_GIGABIT
+ | SKY2_HW_ADV_POWER_CTL;
+ break;
+
case CHIP_ID_YUKON_OPT:
hw->flags = SKY2_HW_GIGABIT
+ | SKY2_HW_NEW_LE
| SKY2_HW_ADV_POWER_CTL;
break;
}
sky2_power_on(hw);
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
for (i = 0; i < hw->ports; i++) {
sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
static void sky2_detach(struct net_device *dev)
{
if (netif_running(dev)) {
+ netif_tx_lock(dev);
netif_device_detach(dev); /* stop txq */
+ netif_tx_unlock(dev);
sky2_down(dev);
}
}
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- if ((wol->wolopts & ~sky2_wol_supported(sky2->hw))
- || !device_can_wakeup(&hw->pdev->dev))
+ if ((wol->wolopts & ~sky2_wol_supported(sky2->hw)) ||
+ !device_can_wakeup(&hw->pdev->dev))
return -EOPNOTSUPP;
sky2->wol = wol->wolopts;
return 0x4000;
}
+static int sky2_reg_access_ok(struct sky2_hw *hw, unsigned int b)
+{
+ /* This complicated switch statement is to make sure and
+ * only access regions that are unreserved.
+ * Some blocks are only valid on dual port cards.
+ */
+ switch (b) {
+ /* second port */
+ case 5: /* Tx Arbiter 2 */
+ case 9: /* RX2 */
+ case 14 ... 15: /* TX2 */
+ case 17: case 19: /* Ram Buffer 2 */
+ case 22 ... 23: /* Tx Ram Buffer 2 */
+ case 25: /* Rx MAC Fifo 1 */
+ case 27: /* Tx MAC Fifo 2 */
+ case 31: /* GPHY 2 */
+ case 40 ... 47: /* Pattern Ram 2 */
+ case 52: case 54: /* TCP Segmentation 2 */
+ case 112 ... 116: /* GMAC 2 */
+ return hw->ports > 1;
+
+ case 0: /* Control */
+ case 2: /* Mac address */
+ case 4: /* Tx Arbiter 1 */
+ case 7: /* PCI express reg */
+ case 8: /* RX1 */
+ case 12 ... 13: /* TX1 */
+ case 16: case 18:/* Rx Ram Buffer 1 */
+ case 20 ... 21: /* Tx Ram Buffer 1 */
+ case 24: /* Rx MAC Fifo 1 */
+ case 26: /* Tx MAC Fifo 1 */
+ case 28 ... 29: /* Descriptor and status unit */
+ case 30: /* GPHY 1*/
+ case 32 ... 39: /* Pattern Ram 1 */
+ case 48: case 50: /* TCP Segmentation 1 */
+ case 56 ... 60: /* PCI space */
+ case 80 ... 84: /* GMAC 1 */
+ return 1;
+
+ default:
+ return 0;
+ }
+}
+
/*
* Returns copy of control register region
* Note: ethtool_get_regs always provides full size (16k) buffer
regs->version = 1;
for (b = 0; b < 128; b++) {
- /* This complicated switch statement is to make sure and
- * only access regions that are unreserved.
- * Some blocks are only valid on dual port cards.
- * and block 3 has some special diagnostic registers that
- * are poison.
- */
- switch (b) {
- case 3:
- /* skip diagnostic ram region */
+ /* skip poisonous diagnostic ram region in block 3 */
+ if (b == 3)
memcpy_fromio(p + 0x10, io + 0x10, 128 - 0x10);
- break;
-
- /* dual port cards only */
- case 5: /* Tx Arbiter 2 */
- case 9: /* RX2 */
- case 14 ... 15: /* TX2 */
- case 17: case 19: /* Ram Buffer 2 */
- case 22 ... 23: /* Tx Ram Buffer 2 */
- case 25: /* Rx MAC Fifo 1 */
- case 27: /* Tx MAC Fifo 2 */
- case 31: /* GPHY 2 */
- case 40 ... 47: /* Pattern Ram 2 */
- case 52: case 54: /* TCP Segmentation 2 */
- case 112 ... 116: /* GMAC 2 */
- if (sky2->hw->ports == 1)
- goto reserved;
- /* fall through */
- case 0: /* Control */
- case 2: /* Mac address */
- case 4: /* Tx Arbiter 1 */
- case 7: /* PCI express reg */
- case 8: /* RX1 */
- case 12 ... 13: /* TX1 */
- case 16: case 18:/* Rx Ram Buffer 1 */
- case 20 ... 21: /* Tx Ram Buffer 1 */
- case 24: /* Rx MAC Fifo 1 */
- case 26: /* Tx MAC Fifo 1 */
- case 28 ... 29: /* Descriptor and status unit */
- case 30: /* GPHY 1*/
- case 32 ... 39: /* Pattern Ram 1 */
- case 48: case 50: /* TCP Segmentation 1 */
- case 56 ... 60: /* PCI space */
- case 80 ... 84: /* GMAC 1 */
+ else if (sky2_reg_access_ok(sky2->hw, b))
memcpy_fromio(p, io, 128);
- break;
- default:
-reserved:
+ else
memset(p, 0, 128);
- }
p += 128;
io += 128;
"Optima", /* 0xbc */
};
- if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_OPT)
+ if (chipid >= CHIP_ID_YUKON_XL && chipid <= CHIP_ID_YUKON_OPT)
strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz);
else
snprintf(buf, sz, "(chip %#x)", chipid);
goto err_out_free_netdev;
}
+ netif_carrier_off(dev);
+
netif_napi_add(dev, &hw->napi, sky2_poll, NAPI_WEIGHT);
err = request_irq(pdev->irq, sky2_intr,
INIT_WORK(&hw->restart_work, sky2_restart);
pci_set_drvdata(pdev, hw);
+ pdev->d3_delay = 150;
return 0;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff