#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "1.25"
+#define DRV_VERSION "1.26"
#define PFX DRV_NAME " "
/*
static DEFINE_PCI_DEVICE_TABLE(sky2_id_table) = {
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E01) }, /* SK-9E21M */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) }, /* DGE-560T */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4001) }, /* DGE-550SX */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B02) }, /* DGE-560SX */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4381) }, /* 88E8059 */
{ 0 }
};
sky2_pci_write32(hw, PCI_CFG_REG_1, 0);
+ sky2_write16(hw, B0_CTST, Y2_HW_WOL_ON);
+
/* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */
reg = sky2_read32(hw, B2_GP_IO);
reg |= GLB_GPIO_STAT_RACE_DIS;
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
/* downshift on PHY 88E1112 and 88E1149 is changed */
- if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED)
- && (hw->flags & SKY2_HW_NEWER_PHY)) {
+ if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) &&
+ (hw->flags & SKY2_HW_NEWER_PHY)) {
/* set downshift counter to 3x and enable downshift */
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
/* apply workaround for integrated resistors calibration */
gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17);
gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60);
+ } else if (hw->chip_id == CHIP_ID_YUKON_OPT && hw->chip_rev == 0) {
+ /* apply fixes in PHY AFE */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0x00ff);
+
+ /* apply RDAC termination workaround */
+ gm_phy_write(hw, port, 24, 0x2800);
+ gm_phy_write(hw, port, 23, 0x2001);
+
+ /* set page register back to 0 */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
} else if (hw->chip_id != CHIP_ID_YUKON_EX &&
hw->chip_id < CHIP_ID_YUKON_SUPR) {
/* no effect on Yukon-XL */
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
- if ( !(sky2->flags & SKY2_FLAG_AUTO_SPEED)
- || sky2->speed == SPEED_100) {
+ if (!(sky2->flags & SKY2_FLAG_AUTO_SPEED) ||
+ sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
ledover |= PHY_M_LED_MO_100(MO_LED_ON);
}
unsigned port = sky2->port;
enum flow_control save_mode;
u16 ctrl;
- u32 reg1;
/* Bring hardware out of reset */
sky2_write16(hw, B0_CTST, CS_RST_CLR);
ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT;
sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl);
- /* Turn on legacy PCI-Express PME mode */
- reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
- reg1 |= PCI_Y2_PME_LEGACY;
- sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
+ /* Disable PiG firmware */
+ sky2_write16(hw, B0_CTST, Y2_HW_WOL_OFF);
/* block receiver */
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
-
}
static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port)
if ( (hw->chip_id == CHIP_ID_YUKON_EX &&
hw->chip_rev != CHIP_REV_YU_EX_A0) ||
- hw->chip_id == CHIP_ID_YUKON_FE_P ||
- hw->chip_id == CHIP_ID_YUKON_SUPR) {
+ hw->chip_id >= CHIP_ID_YUKON_FE_P) {
/* Yukon-Extreme B0 and further Extreme devices */
- /* enable Store & Forward mode for TX */
-
- if (dev->mtu <= ETH_DATA_LEN)
- sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
- TX_JUMBO_DIS | TX_STFW_ENA);
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA);
+ } else if (dev->mtu > ETH_DATA_LEN) {
+ /* set Tx GMAC FIFO Almost Empty Threshold */
+ sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR),
+ (ECU_JUMBO_WM << 16) | ECU_AE_THR);
- else
- sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
- TX_JUMBO_ENA| TX_STFW_ENA);
- } else {
- if (dev->mtu <= ETH_DATA_LEN)
- sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA);
- else {
- /* set Tx GMAC FIFO Almost Empty Threshold */
- sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR),
- (ECU_JUMBO_WM << 16) | ECU_AE_THR);
-
- sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_DIS);
-
- /* Can't do offload because of lack of store/forward */
- dev->features &= ~(NETIF_F_TSO | NETIF_F_SG | NETIF_F_ALL_CSUM);
- }
- }
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_DIS);
+ } else
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA);
}
static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
/* On chips without ram buffer, pause is controled by MAC level */
if (!(hw->flags & SKY2_HW_RAM_BUFFER)) {
- sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
- sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
+ /* Pause threshold is scaled by 8 in bytes */
+ if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
+ hw->chip_rev == CHIP_REV_YU_FE2_A0)
+ reg = 1568 / 8;
+ else
+ reg = 1024 / 8;
+ sky2_write16(hw, SK_REG(port, RX_GMF_UP_THR), reg);
+ sky2_write16(hw, SK_REG(port, RX_GMF_LP_THR), 768 / 8);
sky2_set_tx_stfwd(hw, port);
}
static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2, u16 *slot)
{
struct sky2_tx_le *le = sky2->tx_le + *slot;
- struct tx_ring_info *re = sky2->tx_ring + *slot;
*slot = RING_NEXT(*slot, sky2->tx_ring_size);
- re->flags = 0;
- re->skb = NULL;
le->ctrl = 0;
return le;
}
return le;
}
+static unsigned sky2_get_rx_threshold(struct sky2_port* sky2)
+{
+ unsigned size;
+
+ /* Space needed for frame data + headers rounded up */
+ size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8);
+
+ /* Stopping point for hardware truncation */
+ return (size - 8) / sizeof(u32);
+}
+
+static unsigned sky2_get_rx_data_size(struct sky2_port* sky2)
+{
+ struct rx_ring_info *re;
+ unsigned size;
+
+ /* Space needed for frame data + headers rounded up */
+ size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8);
+
+ sky2->rx_nfrags = size >> PAGE_SHIFT;
+ BUG_ON(sky2->rx_nfrags > ARRAY_SIZE(re->frag_addr));
+
+ /* Compute residue after pages */
+ size -= sky2->rx_nfrags << PAGE_SHIFT;
+
+ /* Optimize to handle small packets and headers */
+ if (size < copybreak)
+ size = copybreak;
+ if (size < ETH_HLEN)
+ size = ETH_HLEN;
+
+ return size;
+}
+
/* Build description to hardware for one receive segment */
static void sky2_rx_add(struct sky2_port *sky2, u8 op,
dma_addr_t map, unsigned len)
int i;
re->data_addr = pci_map_single(pdev, skb->data, size, PCI_DMA_FROMDEVICE);
- if (unlikely(pci_dma_mapping_error(pdev, re->data_addr)))
- return -EIO;
+ if (pci_dma_mapping_error(pdev, re->data_addr))
+ goto mapping_error;
pci_unmap_len_set(re, data_size, size);
- for (i = 0; i < skb_shinfo(skb)->nr_frags; i++)
- re->frag_addr[i] = pci_map_page(pdev,
- skb_shinfo(skb)->frags[i].page,
- skb_shinfo(skb)->frags[i].page_offset,
- skb_shinfo(skb)->frags[i].size,
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+
+ re->frag_addr[i] = pci_map_page(pdev, frag->page,
+ frag->page_offset,
+ frag->size,
PCI_DMA_FROMDEVICE);
+
+ if (pci_dma_mapping_error(pdev, re->frag_addr[i]))
+ goto map_page_error;
+ }
return 0;
+
+map_page_error:
+ while (--i >= 0) {
+ pci_unmap_page(pdev, re->frag_addr[i],
+ skb_shinfo(skb)->frags[i].size,
+ PCI_DMA_FROMDEVICE);
+ }
+
+ pci_unmap_single(pdev, re->data_addr, pci_unmap_len(re, data_size),
+ PCI_DMA_FROMDEVICE);
+
+mapping_error:
+ if (net_ratelimit())
+ dev_warn(&pdev->dev, "%s: rx mapping error\n",
+ skb->dev->name);
+ return -EIO;
}
static void sky2_rx_unmap_skb(struct pci_dev *pdev, struct rx_ring_info *re)
sky2_put_idx(sky2->hw, rxq, sky2->rx_put);
}
+static int sky2_alloc_rx_skbs(struct sky2_port *sky2)
+{
+ struct sky2_hw *hw = sky2->hw;
+ unsigned i;
+
+ sky2->rx_data_size = sky2_get_rx_data_size(sky2);
+
+ /* Fill Rx ring */
+ for (i = 0; i < sky2->rx_pending; i++) {
+ struct rx_ring_info *re = sky2->rx_ring + i;
+
+ re->skb = sky2_rx_alloc(sky2);
+ if (!re->skb)
+ return -ENOMEM;
+
+ if (sky2_rx_map_skb(hw->pdev, re, sky2->rx_data_size)) {
+ dev_kfree_skb(re->skb);
+ re->skb = NULL;
+ return -ENOMEM;
+ }
+ }
+ return 0;
+}
+
/*
- * Allocate and setup receiver buffer pool.
+ * Setup receiver buffer pool.
* Normal case this ends up creating one list element for skb
* in the receive ring. Worst case if using large MTU and each
* allocation falls on a different 64 bit region, that results
* One element is used for checksum enable/disable, and one
* extra to avoid wrap.
*/
-static int sky2_rx_start(struct sky2_port *sky2)
+static void sky2_rx_start(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
struct rx_ring_info *re;
unsigned rxq = rxqaddr[sky2->port];
- unsigned i, size, thresh;
+ unsigned i, thresh;
sky2->rx_put = sky2->rx_next = 0;
sky2_qset(hw, rxq);
/* These chips have no ram buffer?
* MAC Rx RAM Read is controlled by hardware */
if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
- (hw->chip_rev == CHIP_REV_YU_EC_U_A1
- || hw->chip_rev == CHIP_REV_YU_EC_U_B0))
+ (hw->chip_rev == CHIP_REV_YU_EC_U_A1 ||
+ hw->chip_rev == CHIP_REV_YU_EC_U_B0))
sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS);
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
if (!(hw->flags & SKY2_HW_NEW_LE))
rx_set_checksum(sky2);
- /* Space needed for frame data + headers rounded up */
- size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8);
-
- /* Stopping point for hardware truncation */
- thresh = (size - 8) / sizeof(u32);
-
- sky2->rx_nfrags = size >> PAGE_SHIFT;
- BUG_ON(sky2->rx_nfrags > ARRAY_SIZE(re->frag_addr));
-
- /* Compute residue after pages */
- size -= sky2->rx_nfrags << PAGE_SHIFT;
-
- /* Optimize to handle small packets and headers */
- if (size < copybreak)
- size = copybreak;
- if (size < ETH_HLEN)
- size = ETH_HLEN;
-
- sky2->rx_data_size = size;
-
- /* Fill Rx ring */
+ /* submit Rx ring */
for (i = 0; i < sky2->rx_pending; i++) {
re = sky2->rx_ring + i;
-
- re->skb = sky2_rx_alloc(sky2);
- if (!re->skb)
- goto nomem;
-
- if (sky2_rx_map_skb(hw->pdev, re, sky2->rx_data_size)) {
- dev_kfree_skb(re->skb);
- re->skb = NULL;
- goto nomem;
- }
-
sky2_rx_submit(sky2, re);
}
* the register is limited to 9 bits, so if you do frames > 2052
* you better get the MTU right!
*/
+ thresh = sky2_get_rx_threshold(sky2);
if (thresh > 0x1ff)
sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_OFF);
else {
/* Tell chip about available buffers */
sky2_rx_update(sky2, rxq);
- return 0;
-nomem:
- sky2_rx_clean(sky2);
- return -ENOMEM;
+
+ if (hw->chip_id == CHIP_ID_YUKON_EX ||
+ hw->chip_id == CHIP_ID_YUKON_SUPR) {
+ /*
+ * Disable flushing of non ASF packets;
+ * must be done after initializing the BMUs;
+ * drivers without ASF support should do this too, otherwise
+ * it may happen that they cannot run on ASF devices;
+ * remember that the MAC FIFO isn't reset during initialization.
+ */
+ sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_MACSEC_FLUSH_OFF);
+ }
+
+ if (hw->chip_id >= CHIP_ID_YUKON_SUPR) {
+ /* Enable RX Home Address & Routing Header checksum fix */
+ sky2_write16(hw, SK_REG(sky2->port, RX_GMF_FL_CTRL),
+ RX_IPV6_SA_MOB_ENA | RX_IPV6_DA_MOB_ENA);
+
+ /* Enable TX Home Address & Routing Header checksum fix */
+ sky2_write32(hw, Q_ADDR(txqaddr[sky2->port], Q_TEST),
+ TBMU_TEST_HOME_ADD_FIX_EN | TBMU_TEST_ROUTING_ADD_FIX_EN);
+ }
}
static int sky2_alloc_buffers(struct sky2_port *sky2)
if (!sky2->rx_ring)
goto nomem;
- return 0;
+ return sky2_alloc_rx_skbs(sky2);
nomem:
return -ENOMEM;
}
{
struct sky2_hw *hw = sky2->hw;
+ sky2_rx_clean(sky2);
+
if (sky2->rx_le) {
pci_free_consistent(hw->pdev, RX_LE_BYTES,
sky2->rx_le, sky2->rx_le_map);
sky2->rx_ring = NULL;
}
-/* Bring up network interface. */
-static int sky2_up(struct net_device *dev)
+static void sky2_hw_up(struct sky2_port *sky2)
{
- struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
- u32 imask, ramsize;
- int cap, err;
+ u32 ramsize;
+ int cap;
struct net_device *otherdev = hw->dev[sky2->port^1];
+ tx_init(sky2);
+
/*
* On dual port PCI-X card, there is an problem where status
* can be received out of order due to split transactions
cmd = sky2_pci_read16(hw, cap + PCI_X_CMD);
cmd &= ~PCI_X_CMD_MAX_SPLIT;
sky2_pci_write16(hw, cap + PCI_X_CMD, cmd);
-
- }
-
- netif_carrier_off(dev);
-
- err = sky2_alloc_buffers(sky2);
- if (err)
- goto err_out;
-
- tx_init(sky2);
+ }
sky2_mac_init(hw, port);
if (ramsize > 0) {
u32 rxspace;
- pr_debug(PFX "%s: ram buffer %dK\n", dev->name, ramsize);
+ pr_debug(PFX "%s: ram buffer %dK\n", sky2->netdev->name, ramsize);
if (ramsize < 16)
rxspace = ramsize / 2;
else
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF);
/* Set almost empty threshold */
- if (hw->chip_id == CHIP_ID_YUKON_EC_U
- && hw->chip_rev == CHIP_REV_YU_EC_U_A0)
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
+ hw->chip_rev == CHIP_REV_YU_EC_U_A0)
sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
sky2_set_vlan_mode(hw, port, sky2->vlgrp != NULL);
#endif
- err = sky2_rx_start(sky2);
+ sky2_rx_start(sky2);
+}
+
+/* Bring up network interface. */
+static int sky2_up(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ u32 imask;
+ int err;
+
+ netif_carrier_off(dev);
+
+ err = sky2_alloc_buffers(sky2);
if (err)
goto err_out;
+ sky2_hw_up(sky2);
+
/* Enable interrupts from phy/mac for port */
imask = sky2_read32(hw, B0_IMSK);
imask |= portirq_msk[port];
return count;
}
-static void sky2_tx_unmap(struct pci_dev *pdev,
- const struct tx_ring_info *re)
+static void sky2_tx_unmap(struct pci_dev *pdev, struct tx_ring_info *re)
{
if (re->flags & TX_MAP_SINGLE)
pci_unmap_single(pdev, pci_unmap_addr(re, mapaddr),
pci_unmap_page(pdev, pci_unmap_addr(re, mapaddr),
pci_unmap_len(re, maplen),
PCI_DMA_TODEVICE);
+ re->flags = 0;
}
/*
dev->stats.tx_packets++;
dev->stats.tx_bytes += skb->len;
+ re->skb = NULL;
dev_kfree_skb_any(skb);
sky2->tx_next = RING_NEXT(idx, sky2->tx_ring_size);
sky2->tx_cons = idx;
smp_mb();
- if (tx_avail(sky2) > MAX_SKB_TX_LE + 4)
+ /* Wake unless it's detached, and called e.g. from sky2_down() */
+ if (tx_avail(sky2) > MAX_SKB_TX_LE + 4 && netif_device_present(dev))
netif_wake_queue(dev);
}
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* Workaround shared GMAC reset */
- if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
- && port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
+ if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 &&
+ port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
/* Free any pending frames stuck in HW queue */
sky2_tx_complete(sky2, sky2->tx_prod);
- sky2_rx_clean(sky2);
-
sky2_free_buffers(sky2);
return 0;
netif_carrier_off(sky2->netdev);
- /* Turn on link LED */
+ /* Turn off link LED */
sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
if (netif_msg_link(sky2))
sky2->flow_status = FC_TX;
}
- if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
- && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
+ if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000 &&
+ !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
sky2->flow_status = FC_NONE;
if (sky2->flow_status & FC_TX)
spin_unlock(&sky2->phy_lock);
}
+/* Special quick link interrupt (Yukon-2 Optima only) */
+static void sky2_qlink_intr(struct sky2_hw *hw)
+{
+ struct sky2_port *sky2 = netdev_priv(hw->dev[0]);
+ u32 imask;
+ u16 phy;
+
+ /* disable irq */
+ imask = sky2_read32(hw, B0_IMSK);
+ imask &= ~Y2_IS_PHY_QLNK;
+ sky2_write32(hw, B0_IMSK, imask);
+
+ /* reset PHY Link Detect */
+ phy = sky2_pci_read16(hw, PSM_CONFIG_REG4);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ sky2_pci_write16(hw, PSM_CONFIG_REG4, phy | 1);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ sky2_link_up(sky2);
+}
+
/* Transmit timeout is only called if we are running, carrier is up
* and tx queue is full (stopped).
*/
u16 ctl, mode;
u32 imask;
+ /* MTU size outside the spec */
if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
return -EINVAL;
+ /* MTU > 1500 on yukon FE and FE+ not allowed */
if (new_mtu > ETH_DATA_LEN &&
(hw->chip_id == CHIP_ID_YUKON_FE ||
hw->chip_id == CHIP_ID_YUKON_FE_P))
return -EINVAL;
+ /* TSO, etc on Yukon Ultra and MTU > 1500 not supported */
+ if (new_mtu > ETH_DATA_LEN && hw->chip_id == CHIP_ID_YUKON_EC_U)
+ dev->features &= ~(NETIF_F_TSO|NETIF_F_SG|NETIF_F_ALL_CSUM);
+
if (!netif_running(dev)) {
dev->mtu = new_mtu;
return 0;
sky2_write8(hw, RB_ADDR(rxqaddr[port], RB_CTRL), RB_ENA_OP_MD);
- err = sky2_rx_start(sky2);
+ err = sky2_alloc_rx_skbs(sky2);
+ if (!err)
+ sky2_rx_start(sky2);
+ else
+ sky2_rx_clean(sky2);
sky2_write32(hw, B0_IMSK, imask);
sky2_read32(hw, B0_Y2_SP_LISR);
{
struct sk_buff *skb;
- skb = netdev_alloc_skb(sky2->netdev, length + 2);
+ skb = netdev_alloc_skb_ip_align(sky2->netdev, length);
if (likely(skb)) {
- skb_reserve(skb, 2);
pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->data_addr,
length, PCI_DMA_FROMDEVICE);
skb_copy_from_linear_data(re->skb, skb->data, length);
struct rx_ring_info *re,
unsigned int length)
{
- struct sk_buff *skb, *nskb;
+ struct sk_buff *skb;
+ struct rx_ring_info nre;
unsigned hdr_space = sky2->rx_data_size;
- /* Don't be tricky about reusing pages (yet) */
- nskb = sky2_rx_alloc(sky2);
- if (unlikely(!nskb))
- return NULL;
+ nre.skb = sky2_rx_alloc(sky2);
+ if (unlikely(!nre.skb))
+ goto nobuf;
+
+ if (sky2_rx_map_skb(sky2->hw->pdev, &nre, hdr_space))
+ goto nomap;
skb = re->skb;
sky2_rx_unmap_skb(sky2->hw->pdev, re);
-
prefetch(skb->data);
- re->skb = nskb;
- if (sky2_rx_map_skb(sky2->hw->pdev, re, hdr_space)) {
- dev_kfree_skb(nskb);
- re->skb = skb;
- return NULL;
- }
+ *re = nre;
if (skb_shinfo(skb)->nr_frags)
skb_put_frags(skb, hdr_space, length);
else
skb_put(skb, length);
return skb;
+
+nomap:
+ dev_kfree_skb(nre.skb);
+nobuf:
+ return NULL;
}
/*
skb = receive_copy(sky2, re, length);
else
skb = receive_new(sky2, re, length);
+
+ dev->stats.rx_dropped += (skb == NULL);
+
resubmit:
sky2_rx_submit(sky2, re);
}
}
+static void sky2_rx_checksum(struct sky2_port *sky2, u32 status)
+{
+ /* If this happens then driver assuming wrong format for chip type */
+ BUG_ON(sky2->hw->flags & SKY2_HW_NEW_LE);
+
+ /* Both checksum counters are programmed to start at
+ * the same offset, so unless there is a problem they
+ * should match. This failure is an early indication that
+ * hardware receive checksumming won't work.
+ */
+ if (likely((u16)(status >> 16) == (u16)status)) {
+ struct sk_buff *skb = sky2->rx_ring[sky2->rx_next].skb;
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ skb->csum = le16_to_cpu(status);
+ } else {
+ dev_notice(&sky2->hw->pdev->dev,
+ "%s: receive checksum problem (status = %#x)\n",
+ sky2->netdev->name, status);
+
+ /* Disable checksum offload */
+ sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM;
+ sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR),
+ BMU_DIS_RX_CHKSUM);
+ }
+}
+
/* Process status response ring */
static int sky2_status_intr(struct sky2_hw *hw, int to_do, u16 idx)
{
case OP_RXSTAT:
total_packets[port]++;
total_bytes[port] += length;
+
skb = sky2_receive(dev, length, status);
- if (unlikely(!skb)) {
- dev->stats.rx_dropped++;
+ if (!skb)
break;
- }
/* This chip reports checksum status differently */
if (hw->flags & SKY2_HW_NEW_LE) {
/* fall through */
#endif
case OP_RXCHKS:
- if (!(sky2->flags & SKY2_FLAG_RX_CHECKSUM))
- break;
-
- /* If this happens then driver assuming wrong format */
- if (unlikely(hw->flags & SKY2_HW_NEW_LE)) {
- if (net_ratelimit())
- printk(KERN_NOTICE "%s: unexpected"
- " checksum status\n",
- dev->name);
- break;
- }
-
- /* Both checksum counters are programmed to start at
- * the same offset, so unless there is a problem they
- * should match. This failure is an early indication that
- * hardware receive checksumming won't work.
- */
- if (likely(status >> 16 == (status & 0xffff))) {
- skb = sky2->rx_ring[sky2->rx_next].skb;
- skb->ip_summed = CHECKSUM_COMPLETE;
- skb->csum = le16_to_cpu(status);
- } else {
- printk(KERN_NOTICE PFX "%s: hardware receive "
- "checksum problem (status = %#x)\n",
- dev->name, status);
- sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM;
-
- sky2_write32(sky2->hw,
- Q_ADDR(rxqaddr[port], Q_CSR),
- BMU_DIS_RX_CHKSUM);
- }
+ if (likely(sky2->flags & SKY2_FLAG_RX_CHECKSUM))
+ sky2_rx_checksum(sky2, status);
break;
case OP_TXINDEXLE:
if (status & Y2_IS_IRQ_PHY2)
sky2_phy_intr(hw, 1);
+ if (status & Y2_IS_PHY_QLNK)
+ sky2_qlink_intr(hw);
+
while ((idx = sky2_read16(hw, STAT_PUT_IDX)) != hw->st_idx) {
work_done += sky2_status_intr(hw, work_limit - work_done, idx);
case CHIP_ID_YUKON_EX:
case CHIP_ID_YUKON_SUPR:
case CHIP_ID_YUKON_UL_2:
+ case CHIP_ID_YUKON_OPT:
return 125;
case CHIP_ID_YUKON_FE:
| SKY2_HW_ADV_POWER_CTL;
break;
+ case CHIP_ID_YUKON_OPT:
+ hw->flags = SKY2_HW_GIGABIT
+ | SKY2_HW_NEW_LE
+ | SKY2_HW_ADV_POWER_CTL;
+ break;
+
default:
dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
hw->chip_id);
u32 hwe_mask = Y2_HWE_ALL_MASK;
/* disable ASF */
- if (hw->chip_id == CHIP_ID_YUKON_EX) {
+ if (hw->chip_id == CHIP_ID_YUKON_EX
+ || hw->chip_id == CHIP_ID_YUKON_SUPR) {
+ sky2_write32(hw, CPU_WDOG, 0);
status = sky2_read16(hw, HCU_CCSR);
status &= ~(HCU_CCSR_AHB_RST | HCU_CCSR_CPU_RST_MODE |
HCU_CCSR_UC_STATE_MSK);
+ /*
+ * CPU clock divider shouldn't be used because
+ * - ASF firmware may malfunction
+ * - Yukon-Supreme: Parallel FLASH doesn't support divided clocks
+ */
+ status &= ~HCU_CCSR_CPU_CLK_DIVIDE_MSK;
sky2_write16(hw, HCU_CCSR, status);
+ sky2_write32(hw, CPU_WDOG, 0);
} else
sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
sky2_write16(hw, SK_REG(i, GMAC_CTRL),
GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON
| GMC_BYP_RETR_ON);
+
+ }
+
+ if (hw->chip_id == CHIP_ID_YUKON_SUPR && hw->chip_rev > CHIP_REV_YU_SU_B0) {
+ /* enable MACSec clock gating */
+ sky2_pci_write32(hw, PCI_DEV_REG3, P_CLK_MACSEC_DIS);
+ }
+
+ if (hw->chip_id == CHIP_ID_YUKON_OPT) {
+ u16 reg;
+ u32 msk;
+
+ if (hw->chip_rev == 0) {
+ /* disable PCI-E PHY power down (set PHY reg 0x80, bit 7 */
+ sky2_write32(hw, Y2_PEX_PHY_DATA, (0x80UL << 16) | (1 << 7));
+
+ /* set PHY Link Detect Timer to 1.1 second (11x 100ms) */
+ reg = 10;
+ } else {
+ /* set PHY Link Detect Timer to 0.4 second (4x 100ms) */
+ reg = 3;
+ }
+
+ reg <<= PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_BASE;
+
+ /* reset PHY Link Detect */
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ sky2_pci_write16(hw, PSM_CONFIG_REG4,
+ reg | PSM_CONFIG_REG4_RST_PHY_LINK_DETECT);
+ sky2_pci_write16(hw, PSM_CONFIG_REG4, reg);
+
+
+ /* enable PHY Quick Link */
+ msk = sky2_read32(hw, B0_IMSK);
+ msk |= Y2_IS_PHY_QLNK;
+ sky2_write32(hw, B0_IMSK, msk);
+
+ /* check if PSMv2 was running before */
+ reg = sky2_pci_read16(hw, PSM_CONFIG_REG3);
+ if (reg & PCI_EXP_LNKCTL_ASPMC) {
+ cap = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+ /* restore the PCIe Link Control register */
+ sky2_pci_write16(hw, cap + PCI_EXP_LNKCTL, reg);
+ }
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ /* re-enable PEX PM in PEX PHY debug reg. 8 (clear bit 12) */
+ sky2_write32(hw, Y2_PEX_PHY_DATA, PEX_DB_ACCESS | (0x08UL << 16));
}
/* Clear I2C IRQ noise */
static void sky2_detach(struct net_device *dev)
{
if (netif_running(dev)) {
+ netif_tx_lock(dev);
netif_device_detach(dev); /* stop txq */
+ netif_tx_unlock(dev);
sky2_down(dev);
}
}
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- if ((wol->wolopts & ~sky2_wol_supported(sky2->hw))
- || !device_can_wakeup(&hw->pdev->dev))
+ if ((wol->wolopts & ~sky2_wol_supported(sky2->hw)) ||
+ !device_can_wakeup(&hw->pdev->dev))
return -EOPNOTSUPP;
sky2->wol = wol->wolopts;
-
- if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
- hw->chip_id == CHIP_ID_YUKON_EX ||
- hw->chip_id == CHIP_ID_YUKON_FE_P)
- sky2_write32(hw, B0_CTST, sky2->wol
- ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF);
-
- device_set_wakeup_enable(&hw->pdev->dev, sky2->wol);
-
- if (!netif_running(dev))
- sky2_wol_init(sky2);
return 0;
}
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
else if (dev->flags & IFF_ALLMULTI)
memset(filter, 0xff, sizeof(filter));
- else if (dev->mc_count == 0 && !rx_pause)
+ else if (netdev_mc_empty(dev) && !rx_pause)
reg &= ~GM_RXCR_MCF_ENA;
else {
int i;
if (rx_pause)
sky2_add_filter(filter, pause_mc_addr);
- for (i = 0; list && i < dev->mc_count; i++, list = list->next)
+ for (i = 0; list && i < netdev_mc_count(dev); i++, list = list->next)
sky2_add_filter(filter, list->dmi_addr);
}
return 0x4000;
}
+static int sky2_reg_access_ok(struct sky2_hw *hw, unsigned int b)
+{
+ /* This complicated switch statement is to make sure and
+ * only access regions that are unreserved.
+ * Some blocks are only valid on dual port cards.
+ */
+ switch (b) {
+ /* second port */
+ case 5: /* Tx Arbiter 2 */
+ case 9: /* RX2 */
+ case 14 ... 15: /* TX2 */
+ case 17: case 19: /* Ram Buffer 2 */
+ case 22 ... 23: /* Tx Ram Buffer 2 */
+ case 25: /* Rx MAC Fifo 1 */
+ case 27: /* Tx MAC Fifo 2 */
+ case 31: /* GPHY 2 */
+ case 40 ... 47: /* Pattern Ram 2 */
+ case 52: case 54: /* TCP Segmentation 2 */
+ case 112 ... 116: /* GMAC 2 */
+ return hw->ports > 1;
+
+ case 0: /* Control */
+ case 2: /* Mac address */
+ case 4: /* Tx Arbiter 1 */
+ case 7: /* PCI express reg */
+ case 8: /* RX1 */
+ case 12 ... 13: /* TX1 */
+ case 16: case 18:/* Rx Ram Buffer 1 */
+ case 20 ... 21: /* Tx Ram Buffer 1 */
+ case 24: /* Rx MAC Fifo 1 */
+ case 26: /* Tx MAC Fifo 1 */
+ case 28 ... 29: /* Descriptor and status unit */
+ case 30: /* GPHY 1*/
+ case 32 ... 39: /* Pattern Ram 1 */
+ case 48: case 50: /* TCP Segmentation 1 */
+ case 56 ... 60: /* PCI space */
+ case 80 ... 84: /* GMAC 1 */
+ return 1;
+
+ default:
+ return 0;
+ }
+}
+
/*
* Returns copy of control register region
* Note: ethtool_get_regs always provides full size (16k) buffer
regs->version = 1;
for (b = 0; b < 128; b++) {
- /* This complicated switch statement is to make sure and
- * only access regions that are unreserved.
- * Some blocks are only valid on dual port cards.
- * and block 3 has some special diagnostic registers that
- * are poison.
- */
- switch (b) {
- case 3:
- /* skip diagnostic ram region */
+ /* skip poisonous diagnostic ram region in block 3 */
+ if (b == 3)
memcpy_fromio(p + 0x10, io + 0x10, 128 - 0x10);
- break;
-
- /* dual port cards only */
- case 5: /* Tx Arbiter 2 */
- case 9: /* RX2 */
- case 14 ... 15: /* TX2 */
- case 17: case 19: /* Ram Buffer 2 */
- case 22 ... 23: /* Tx Ram Buffer 2 */
- case 25: /* Rx MAC Fifo 1 */
- case 27: /* Tx MAC Fifo 2 */
- case 31: /* GPHY 2 */
- case 40 ... 47: /* Pattern Ram 2 */
- case 52: case 54: /* TCP Segmentation 2 */
- case 112 ... 116: /* GMAC 2 */
- if (sky2->hw->ports == 1)
- goto reserved;
- /* fall through */
- case 0: /* Control */
- case 2: /* Mac address */
- case 4: /* Tx Arbiter 1 */
- case 7: /* PCI express reg */
- case 8: /* RX1 */
- case 12 ... 13: /* TX1 */
- case 16: case 18:/* Rx Ram Buffer 1 */
- case 20 ... 21: /* Tx Ram Buffer 1 */
- case 24: /* Rx MAC Fifo 1 */
- case 26: /* Tx MAC Fifo 1 */
- case 28 ... 29: /* Descriptor and status unit */
- case 30: /* GPHY 1*/
- case 32 ... 39: /* Pattern Ram 1 */
- case 48: case 50: /* TCP Segmentation 1 */
- case 56 ... 60: /* PCI space */
- case 80 ... 84: /* GMAC 1 */
+ else if (sky2_reg_access_ok(sky2->hw, b))
memcpy_fromio(p, io, 128);
- break;
- default:
-reserved:
+ else
memset(p, 0, 128);
- }
p += 128;
io += 128;
"FE+", /* 0xb8 */
"Supreme", /* 0xb9 */
"UL 2", /* 0xba */
+ "Unknown", /* 0xbb */
+ "Optima", /* 0xbc */
};
- if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_UL_2)
+ if (chipid >= CHIP_ID_YUKON_XL && chipid <= CHIP_ID_YUKON_OPT)
strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz);
else
snprintf(buf, sz, "(chip %#x)", chipid);
INIT_WORK(&hw->restart_work, sky2_restart);
pci_set_drvdata(pdev, hw);
+ pdev->d3_delay = 150;
return 0;
pci_set_drvdata(pdev, NULL);
}
-#ifdef CONFIG_PM
static int sky2_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
wol |= sky2->wol;
}
+ device_set_wakeup_enable(&pdev->dev, wol != 0);
+
sky2_write32(hw, B0_IMSK, 0);
napi_disable(&hw->napi);
sky2_power_aux(hw);
return 0;
}
+#ifdef CONFIG_PM
static int sky2_resume(struct pci_dev *pdev)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
/* Re-enable all clocks */
- if (hw->chip_id == CHIP_ID_YUKON_EX ||
- hw->chip_id == CHIP_ID_YUKON_EC_U ||
- hw->chip_id == CHIP_ID_YUKON_FE_P)
- sky2_pci_write32(hw, PCI_DEV_REG3, 0);
+ err = pci_write_config_dword(pdev, PCI_DEV_REG3, 0);
+ if (err) {
+ dev_err(&pdev->dev, "PCI write config failed\n");
+ goto out;
+ }
sky2_reset(hw);
sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
static void sky2_shutdown(struct pci_dev *pdev)
{
- struct sky2_hw *hw = pci_get_drvdata(pdev);
- int i, wol = 0;
-
- if (!hw)
- return;
-
- rtnl_lock();
- del_timer_sync(&hw->watchdog_timer);
-
- for (i = 0; i < hw->ports; i++) {
- struct net_device *dev = hw->dev[i];
- struct sky2_port *sky2 = netdev_priv(dev);
-
- if (sky2->wol) {
- wol = 1;
- sky2_wol_init(sky2);
- }
- }
-
- if (wol)
- sky2_power_aux(hw);
- rtnl_unlock();
-
- pci_enable_wake(pdev, PCI_D3hot, wol);
- pci_enable_wake(pdev, PCI_D3cold, wol);
-
- pci_disable_device(pdev);
- pci_set_power_state(pdev, PCI_D3hot);
+ sky2_suspend(pdev, PMSG_SUSPEND);
}
static struct pci_driver sky2_driver = {
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff