/*******************************************************************************
Intel 10 Gigabit PCI Express Linux driver
- Copyright(c) 1999 - 2008 Intel Corporation.
+ Copyright(c) 1999 - 2010 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/sched.h>
+#include <linux/list.h>
+#include <linux/netdevice.h>
+#include "ixgbe.h"
#include "ixgbe_common.h"
#include "ixgbe_phy.h"
static void ixgbe_enable_rar(struct ixgbe_hw *hw, u32 index);
static void ixgbe_disable_rar(struct ixgbe_hw *hw, u32 index);
static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
-static void ixgbe_add_mc_addr(struct ixgbe_hw *hw, u8 *mc_addr);
static void ixgbe_add_uc_addr(struct ixgbe_hw *hw, u8 *addr, u32 vmdq);
+static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num);
/**
* ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
/* Identify the PHY */
hw->phy.ops.identify(hw);
- /*
- * Store MAC address from RAR0, clear receive address registers, and
- * clear the multicast table
- */
- hw->mac.ops.init_rx_addrs(hw);
-
/* Clear the VLAN filter table */
hw->mac.ops.clear_vfta(hw);
- /* Set up link */
- hw->mac.ops.setup_link(hw);
-
/* Clear statistics registers */
hw->mac.ops.clear_hw_cntrs(hw);
IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext);
IXGBE_WRITE_FLUSH(hw);
+ /* Setup flow control */
+ ixgbe_setup_fc(hw, 0);
+
/* Clear adapter stopped flag */
hw->adapter_stopped = false;
**/
s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw)
{
+ s32 status;
+
/* Reset the hardware */
- hw->mac.ops.reset_hw(hw);
+ status = hw->mac.ops.reset_hw(hw);
- /* Start the HW */
- hw->mac.ops.start_hw(hw);
+ if (status == 0) {
+ /* Start the HW */
+ status = hw->mac.ops.start_hw(hw);
+ }
- return 0;
+ return status;
}
/**
}
/**
+ * ixgbe_get_bus_info_generic - Generic set PCI bus info
+ * @hw: pointer to hardware structure
+ *
+ * Sets the PCI bus info (speed, width, type) within the ixgbe_hw structure
+ **/
+s32 ixgbe_get_bus_info_generic(struct ixgbe_hw *hw)
+{
+ struct ixgbe_adapter *adapter = hw->back;
+ struct ixgbe_mac_info *mac = &hw->mac;
+ u16 link_status;
+
+ hw->bus.type = ixgbe_bus_type_pci_express;
+
+ /* Get the negotiated link width and speed from PCI config space */
+ pci_read_config_word(adapter->pdev, IXGBE_PCI_LINK_STATUS,
+ &link_status);
+
+ switch (link_status & IXGBE_PCI_LINK_WIDTH) {
+ case IXGBE_PCI_LINK_WIDTH_1:
+ hw->bus.width = ixgbe_bus_width_pcie_x1;
+ break;
+ case IXGBE_PCI_LINK_WIDTH_2:
+ hw->bus.width = ixgbe_bus_width_pcie_x2;
+ break;
+ case IXGBE_PCI_LINK_WIDTH_4:
+ hw->bus.width = ixgbe_bus_width_pcie_x4;
+ break;
+ case IXGBE_PCI_LINK_WIDTH_8:
+ hw->bus.width = ixgbe_bus_width_pcie_x8;
+ break;
+ default:
+ hw->bus.width = ixgbe_bus_width_unknown;
+ break;
+ }
+
+ switch (link_status & IXGBE_PCI_LINK_SPEED) {
+ case IXGBE_PCI_LINK_SPEED_2500:
+ hw->bus.speed = ixgbe_bus_speed_2500;
+ break;
+ case IXGBE_PCI_LINK_SPEED_5000:
+ hw->bus.speed = ixgbe_bus_speed_5000;
+ break;
+ default:
+ hw->bus.speed = ixgbe_bus_speed_unknown;
+ break;
+ }
+
+ mac->ops.set_lan_id(hw);
+
+ return 0;
+}
+
+/**
+ * ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices
+ * @hw: pointer to the HW structure
+ *
+ * Determines the LAN function id by reading memory-mapped registers
+ * and swaps the port value if requested.
+ **/
+void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw)
+{
+ struct ixgbe_bus_info *bus = &hw->bus;
+ u32 reg;
+
+ reg = IXGBE_READ_REG(hw, IXGBE_STATUS);
+ bus->func = (reg & IXGBE_STATUS_LAN_ID) >> IXGBE_STATUS_LAN_ID_SHIFT;
+ bus->lan_id = bus->func;
+
+ /* check for a port swap */
+ reg = IXGBE_READ_REG(hw, IXGBE_FACTPS);
+ if (reg & IXGBE_FACTPS_LFS)
+ bus->func ^= 0x1;
+}
+
+/**
* ixgbe_stop_adapter_generic - Generic stop Tx/Rx units
* @hw: pointer to hardware structure
*
}
/**
+ * ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM
+ * @hw: pointer to hardware structure
+ * @offset: offset within the EEPROM to be written to
+ * @data: 16 bit word to be written to the EEPROM
+ *
+ * If ixgbe_eeprom_update_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ **/
+s32 ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
+{
+ s32 status;
+ u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI;
+
+ hw->eeprom.ops.init_params(hw);
+
+ if (offset >= hw->eeprom.word_size) {
+ status = IXGBE_ERR_EEPROM;
+ goto out;
+ }
+
+ /* Prepare the EEPROM for writing */
+ status = ixgbe_acquire_eeprom(hw);
+
+ if (status == 0) {
+ if (ixgbe_ready_eeprom(hw) != 0) {
+ ixgbe_release_eeprom(hw);
+ status = IXGBE_ERR_EEPROM;
+ }
+ }
+
+ if (status == 0) {
+ ixgbe_standby_eeprom(hw);
+
+ /* Send the WRITE ENABLE command (8 bit opcode ) */
+ ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_WREN_OPCODE_SPI,
+ IXGBE_EEPROM_OPCODE_BITS);
+
+ ixgbe_standby_eeprom(hw);
+
+ /*
+ * Some SPI eeproms use the 8th address bit embedded in the
+ * opcode
+ */
+ if ((hw->eeprom.address_bits == 8) && (offset >= 128))
+ write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;
+
+ /* Send the Write command (8-bit opcode + addr) */
+ ixgbe_shift_out_eeprom_bits(hw, write_opcode,
+ IXGBE_EEPROM_OPCODE_BITS);
+ ixgbe_shift_out_eeprom_bits(hw, (u16)(offset*2),
+ hw->eeprom.address_bits);
+
+ /* Send the data */
+ data = (data >> 8) | (data << 8);
+ ixgbe_shift_out_eeprom_bits(hw, data, 16);
+ ixgbe_standby_eeprom(hw);
+
+ msleep(hw->eeprom.semaphore_delay);
+ /* Done with writing - release the EEPROM */
+ ixgbe_release_eeprom(hw);
+ }
+
+out:
+ return status;
+}
+
+/**
* ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to be read
static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
{
s32 status = 0;
- u32 eec;
+ u32 eec = 0;
u32 i;
if (ixgbe_acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0)
/* Get the MAC address from the RAR0 for later reference */
hw->mac.ops.get_mac_addr(hw, hw->mac.addr);
- hw_dbg(hw, " Keeping Current RAR0 Addr =%.2X %.2X %.2X ",
- hw->mac.addr[0], hw->mac.addr[1],
- hw->mac.addr[2]);
- hw_dbg(hw, "%.2X %.2X %.2X\n", hw->mac.addr[3],
- hw->mac.addr[4], hw->mac.addr[5]);
+ hw_dbg(hw, " Keeping Current RAR0 Addr =%pM\n", hw->mac.addr);
} else {
/* Setup the receive address. */
hw_dbg(hw, "Overriding MAC Address in RAR[0]\n");
- hw_dbg(hw, " New MAC Addr =%.2X %.2X %.2X ",
- hw->mac.addr[0], hw->mac.addr[1],
- hw->mac.addr[2]);
- hw_dbg(hw, "%.2X %.2X %.2X\n", hw->mac.addr[3],
- hw->mac.addr[4], hw->mac.addr[5]);
+ hw_dbg(hw, " New MAC Addr =%pM\n", hw->mac.addr);
hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV);
}
/**
* ixgbe_update_uc_addr_list_generic - Updates MAC list of secondary addresses
* @hw: pointer to hardware structure
- * @addr_list: the list of new addresses
- * @addr_count: number of addresses
- * @next: iterator function to walk the address list
+ * @uc_list: the list of new addresses
*
* The given list replaces any existing list. Clears the secondary addrs from
* receive address registers. Uses unused receive address registers for the
* Drivers using secondary unicast addresses must set user_set_promisc when
* manually putting the device into promiscuous mode.
**/
-s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list,
- u32 addr_count, ixgbe_mc_addr_itr next)
+s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw,
+ struct list_head *uc_list)
{
- u8 *addr;
u32 i;
u32 old_promisc_setting = hw->addr_ctrl.overflow_promisc;
u32 uc_addr_in_use;
u32 fctrl;
- u32 vmdq;
+ struct netdev_hw_addr *ha;
/*
* Clear accounting of old secondary address list,
* don't count RAR[0]
*/
- uc_addr_in_use = hw->addr_ctrl.rar_used_count -
- hw->addr_ctrl.mc_addr_in_rar_count - 1;
+ uc_addr_in_use = hw->addr_ctrl.rar_used_count - 1;
hw->addr_ctrl.rar_used_count -= uc_addr_in_use;
hw->addr_ctrl.overflow_promisc = 0;
/* Zero out the other receive addresses */
- hw_dbg(hw, "Clearing RAR[1-%d]\n", uc_addr_in_use);
- for (i = 1; i <= uc_addr_in_use; i++) {
- IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0);
- IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0);
+ hw_dbg(hw, "Clearing RAR[1-%d]\n", uc_addr_in_use + 1);
+ for (i = 0; i < uc_addr_in_use; i++) {
+ IXGBE_WRITE_REG(hw, IXGBE_RAL(1+i), 0);
+ IXGBE_WRITE_REG(hw, IXGBE_RAH(1+i), 0);
}
/* Add the new addresses */
- for (i = 0; i < addr_count; i++) {
+ list_for_each_entry(ha, uc_list, list) {
hw_dbg(hw, " Adding the secondary addresses:\n");
- addr = next(hw, &addr_list, &vmdq);
- ixgbe_add_uc_addr(hw, addr, vmdq);
+ ixgbe_add_uc_addr(hw, ha->addr, 0);
}
if (hw->addr_ctrl.overflow_promisc) {
}
/**
- * ixgbe_add_mc_addr - Adds a multicast address.
- * @hw: pointer to hardware structure
- * @mc_addr: new multicast address
- *
- * Adds it to unused receive address register or to the multicast table.
- **/
-static void ixgbe_add_mc_addr(struct ixgbe_hw *hw, u8 *mc_addr)
-{
- u32 rar_entries = hw->mac.num_rar_entries;
- u32 rar;
-
- hw_dbg(hw, " MC Addr =%.2X %.2X %.2X %.2X %.2X %.2X\n",
- mc_addr[0], mc_addr[1], mc_addr[2],
- mc_addr[3], mc_addr[4], mc_addr[5]);
-
- /*
- * Place this multicast address in the RAR if there is room,
- * else put it in the MTA
- */
- if (hw->addr_ctrl.rar_used_count < rar_entries) {
- /* use RAR from the end up for multicast */
- rar = rar_entries - hw->addr_ctrl.mc_addr_in_rar_count - 1;
- hw->mac.ops.set_rar(hw, rar, mc_addr, 0, IXGBE_RAH_AV);
- hw_dbg(hw, "Added a multicast address to RAR[%d]\n", rar);
- hw->addr_ctrl.rar_used_count++;
- hw->addr_ctrl.mc_addr_in_rar_count++;
- } else {
- ixgbe_set_mta(hw, mc_addr);
- }
-
- hw_dbg(hw, "ixgbe_add_mc_addr Complete\n");
-}
-
-/**
* ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses
* @hw: pointer to hardware structure
* @mc_addr_list: the list of new multicast addresses
u32 mc_addr_count, ixgbe_mc_addr_itr next)
{
u32 i;
- u32 rar_entries = hw->mac.num_rar_entries;
u32 vmdq;
/*
* use.
*/
hw->addr_ctrl.num_mc_addrs = mc_addr_count;
- hw->addr_ctrl.rar_used_count -= hw->addr_ctrl.mc_addr_in_rar_count;
- hw->addr_ctrl.mc_addr_in_rar_count = 0;
hw->addr_ctrl.mta_in_use = 0;
- /* Zero out the other receive addresses. */
- hw_dbg(hw, "Clearing RAR[%d-%d]\n", hw->addr_ctrl.rar_used_count,
- rar_entries - 1);
- for (i = hw->addr_ctrl.rar_used_count; i < rar_entries; i++) {
- IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0);
- IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0);
- }
-
/* Clear the MTA */
hw_dbg(hw, " Clearing MTA\n");
for (i = 0; i < hw->mac.mcft_size; i++)
/* Add the new addresses */
for (i = 0; i < mc_addr_count; i++) {
hw_dbg(hw, " Adding the multicast addresses:\n");
- ixgbe_add_mc_addr(hw, next(hw, &mc_addr_list, &vmdq));
+ ixgbe_set_mta(hw, next(hw, &mc_addr_list, &vmdq));
}
/* Enable mta */
}
/**
+ * ixgbe_fc_enable_generic - Enable flow control
+ * @hw: pointer to hardware structure
+ * @packetbuf_num: packet buffer number (0-7)
+ *
+ * Enable flow control according to the current settings.
+ **/
+s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num)
+{
+ s32 ret_val = 0;
+ u32 mflcn_reg, fccfg_reg;
+ u32 reg;
+ u32 rx_pba_size;
+
+#ifdef CONFIG_DCB
+ if (hw->fc.requested_mode == ixgbe_fc_pfc)
+ goto out;
+
+#endif /* CONFIG_DCB */
+ /* Negotiate the fc mode to use */
+ ret_val = ixgbe_fc_autoneg(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable any previous flow control settings */
+ mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN);
+ mflcn_reg &= ~(IXGBE_MFLCN_RFCE | IXGBE_MFLCN_RPFCE);
+
+ fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG);
+ fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY);
+
+ /*
+ * The possible values of fc.current_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * 4: Priority Flow Control is enabled.
+ * other: Invalid.
+ */
+ switch (hw->fc.current_mode) {
+ case ixgbe_fc_none:
+ /*
+ * Flow control is disabled by software override or autoneg.
+ * The code below will actually disable it in the HW.
+ */
+ break;
+ case ixgbe_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ mflcn_reg |= IXGBE_MFLCN_RFCE;
+ break;
+ case ixgbe_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
+ break;
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ mflcn_reg |= IXGBE_MFLCN_RFCE;
+ fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
+ break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ break;
+ }
+
+ /* Set 802.3x based flow control settings. */
+ mflcn_reg |= IXGBE_MFLCN_DPF;
+ IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg);
+ IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg);
+
+ reg = IXGBE_READ_REG(hw, IXGBE_MTQC);
+ /* Thresholds are different for link flow control when in DCB mode */
+ if (reg & IXGBE_MTQC_RT_ENA) {
+ rx_pba_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(packetbuf_num));
+
+ /* Always disable XON for LFC when in DCB mode */
+ reg = (rx_pba_size >> 5) & 0xFFE0;
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(packetbuf_num), reg);
+
+ reg = (rx_pba_size >> 2) & 0xFFE0;
+ if (hw->fc.current_mode & ixgbe_fc_tx_pause)
+ reg |= IXGBE_FCRTH_FCEN;
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(packetbuf_num), reg);
+ } else {
+ /*
+ * Set up and enable Rx high/low water mark thresholds,
+ * enable XON.
+ */
+ if (hw->fc.current_mode & ixgbe_fc_tx_pause) {
+ if (hw->fc.send_xon) {
+ IXGBE_WRITE_REG(hw,
+ IXGBE_FCRTL_82599(packetbuf_num),
+ (hw->fc.low_water |
+ IXGBE_FCRTL_XONE));
+ } else {
+ IXGBE_WRITE_REG(hw,
+ IXGBE_FCRTL_82599(packetbuf_num),
+ hw->fc.low_water);
+ }
+
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(packetbuf_num),
+ (hw->fc.high_water | IXGBE_FCRTH_FCEN));
+ }
+ }
+
+ /* Configure pause time (2 TCs per register) */
+ reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num / 2));
+ if ((packetbuf_num & 1) == 0)
+ reg = (reg & 0xFFFF0000) | hw->fc.pause_time;
+ else
+ reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16);
+ IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg);
+
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1));
+
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_fc_autoneg - Configure flow control
+ * @hw: pointer to hardware structure
+ *
+ * Compares our advertised flow control capabilities to those advertised by
+ * our link partner, and determines the proper flow control mode to use.
+ **/
+s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw)
+{
+ s32 ret_val = 0;
+ ixgbe_link_speed speed;
+ u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
+ u32 links2, anlp1_reg, autoc_reg, links;
+ bool link_up;
+
+ /*
+ * AN should have completed when the cable was plugged in.
+ * Look for reasons to bail out. Bail out if:
+ * - FC autoneg is disabled, or if
+ * - link is not up.
+ *
+ * Since we're being called from an LSC, link is already known to be up.
+ * So use link_up_wait_to_complete=false.
+ */
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+
+ if (hw->fc.disable_fc_autoneg || (!link_up)) {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+
+ /*
+ * On backplane, bail out if
+ * - backplane autoneg was not completed, or if
+ * - we are 82599 and link partner is not AN enabled
+ */
+ if (hw->phy.media_type == ixgbe_media_type_backplane) {
+ links = IXGBE_READ_REG(hw, IXGBE_LINKS);
+ if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+
+ if (hw->mac.type == ixgbe_mac_82599EB) {
+ links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
+ if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+ }
+ }
+
+ /*
+ * On multispeed fiber at 1g, bail out if
+ * - link is up but AN did not complete, or if
+ * - link is up and AN completed but timed out
+ */
+ if (hw->phy.multispeed_fiber && (speed == IXGBE_LINK_SPEED_1GB_FULL)) {
+ linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
+ if (((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
+ ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+ }
+
+ /*
+ * Bail out on
+ * - copper or CX4 adapters
+ * - fiber adapters running at 10gig
+ */
+ if ((hw->phy.media_type == ixgbe_media_type_copper) ||
+ (hw->phy.media_type == ixgbe_media_type_cx4) ||
+ ((hw->phy.media_type == ixgbe_media_type_fiber) &&
+ (speed == IXGBE_LINK_SPEED_10GB_FULL))) {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+
+ /*
+ * Read the AN advertisement and LP ability registers and resolve
+ * local flow control settings accordingly
+ */
+ if ((speed == IXGBE_LINK_SPEED_1GB_FULL) &&
+ (hw->phy.media_type != ixgbe_media_type_backplane)) {
+ pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+ pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
+ if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_full) {
+ hw->fc.current_mode = ixgbe_fc_full;
+ hw_dbg(hw, "Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control=RX PAUSE only\n");
+ }
+ } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+ } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
+ !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\n");
+ }
+ }
+
+ if (hw->phy.media_type == ixgbe_media_type_backplane) {
+ /*
+ * Read the 10g AN autoc and LP ability registers and resolve
+ * local flow control settings accordingly
+ */
+ autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
+
+ if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_full) {
+ hw->fc.current_mode = ixgbe_fc_full;
+ hw_dbg(hw, "Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control=RX PAUSE only\n");
+ }
+ } else if (!(autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
+ (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+ } else if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
+ (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) &&
+ !(anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\n");
+ }
+ }
+ /* Record that current_mode is the result of a successful autoneg */
+ hw->fc.fc_was_autonegged = true;
+
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_setup_fc - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ **/
+static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
+{
+ s32 ret_val = 0;
+ u32 reg;
+
+#ifdef CONFIG_DCB
+ if (hw->fc.requested_mode == ixgbe_fc_pfc) {
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+
+#endif
+ /* Validate the packetbuf configuration */
+ if (packetbuf_num < 0 || packetbuf_num > 7) {
+ hw_dbg(hw, "Invalid packet buffer number [%d], expected range "
+ "is 0-7\n", packetbuf_num);
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * Validate the water mark configuration. Zero water marks are invalid
+ * because it causes the controller to just blast out fc packets.
+ */
+ if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) {
+ hw_dbg(hw, "Invalid water mark configuration\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * Validate the requested mode. Strict IEEE mode does not allow
+ * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
+ */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict "
+ "IEEE mode\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * 10gig parts do not have a word in the EEPROM to determine the
+ * default flow control setting, so we explicitly set it to full.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /*
+ * Set up the 1G flow control advertisement registers so the HW will be
+ * able to do fc autoneg once the cable is plugged in. If we end up
+ * using 10g instead, this is harmless.
+ */
+ reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+
+ /*
+ * The possible values of fc.requested_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+#ifdef CONFIG_DCB
+ * 4: Priority Flow Control is enabled.
+#endif
+ * other: Invalid.
+ */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
+ reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ break;
+ case ixgbe_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ break;
+ case ixgbe_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ reg |= (IXGBE_PCS1GANA_ASM_PAUSE);
+ reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE);
+ break;
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ break;
+ }
+
+ IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
+ reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
+
+ /* Disable AN timeout */
+ if (hw->fc.strict_ieee)
+ reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
+
+ IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
+ hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
+
+ /*
+ * Set up the 10G flow control advertisement registers so the HW
+ * can do fc autoneg once the cable is plugged in. If we end up
+ * using 1g instead, this is harmless.
+ */
+ reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+
+ /*
+ * The possible values of fc.requested_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: Invalid.
+ */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
+ reg &= ~(IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
+ break;
+ case ixgbe_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
+ break;
+ case ixgbe_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ reg |= (IXGBE_AUTOC_ASM_PAUSE);
+ reg &= ~(IXGBE_AUTOC_SYM_PAUSE);
+ break;
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
+ break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ break;
+ }
+ /*
+ * AUTOC restart handles negotiation of 1G and 10G. There is
+ * no need to set the PCS1GCTL register.
+ */
+ reg |= IXGBE_AUTOC_AN_RESTART;
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg);
+ hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
+
+out:
+ return ret_val;
+}
+
+/**
* ixgbe_disable_pcie_master - Disable PCI-express master access
* @hw: pointer to hardware structure
*
while (timeout) {
if (ixgbe_get_eeprom_semaphore(hw))
- return -IXGBE_ERR_SWFW_SYNC;
+ return IXGBE_ERR_SWFW_SYNC;
gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
if (!(gssr & (fwmask | swmask)))
if (!timeout) {
hw_dbg(hw, "Driver can't access resource, GSSR timeout.\n");
- return -IXGBE_ERR_SWFW_SYNC;
+ return IXGBE_ERR_SWFW_SYNC;
}
gssr |= swmask;
ixgbe_release_eeprom_semaphore(hw);
}
+/**
+ * ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit
+ * @hw: pointer to hardware structure
+ * @regval: register value to write to RXCTRL
+ *
+ * Enables the Rx DMA unit
+ **/
+s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval)
+{
+ IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, regval);
+
+ return 0;
+}
+
+/**
+ * ixgbe_blink_led_start_generic - Blink LED based on index.
+ * @hw: pointer to hardware structure
+ * @index: led number to blink
+ **/
+s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index)
+{
+ ixgbe_link_speed speed = 0;
+ bool link_up = 0;
+ u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
+
+ /*
+ * Link must be up to auto-blink the LEDs;
+ * Force it if link is down.
+ */
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+
+ if (!link_up) {
+ autoc_reg |= IXGBE_AUTOC_AN_RESTART;
+ autoc_reg |= IXGBE_AUTOC_FLU;
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
+ msleep(10);
+ }
+
+ led_reg &= ~IXGBE_LED_MODE_MASK(index);
+ led_reg |= IXGBE_LED_BLINK(index);
+ IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
+ IXGBE_WRITE_FLUSH(hw);
+
+ return 0;
+}
+
+/**
+ * ixgbe_blink_led_stop_generic - Stop blinking LED based on index.
+ * @hw: pointer to hardware structure
+ * @index: led number to stop blinking
+ **/
+s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index)
+{
+ u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
+
+ autoc_reg &= ~IXGBE_AUTOC_FLU;
+ autoc_reg |= IXGBE_AUTOC_AN_RESTART;
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
+
+ led_reg &= ~IXGBE_LED_MODE_MASK(index);
+ led_reg &= ~IXGBE_LED_BLINK(index);
+ led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
+ IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
+ IXGBE_WRITE_FLUSH(hw);
+
+ return 0;
+}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff