/*******************************************************************************
Intel PRO/1000 Linux driver
- Copyright(c) 1999 - 2007 Intel Corporation.
+ Copyright(c) 1999 - 2009 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
/*
* 82571EB Gigabit Ethernet Controller
+ * 82571EB Gigabit Ethernet Controller (Copper)
* 82571EB Gigabit Ethernet Controller (Fiber)
+ * 82571EB Dual Port Gigabit Mezzanine Adapter
+ * 82571EB Quad Port Gigabit Mezzanine Adapter
+ * 82571PT Gigabit PT Quad Port Server ExpressModule
* 82572EI Gigabit Ethernet Controller (Copper)
* 82572EI Gigabit Ethernet Controller (Fiber)
* 82572EI Gigabit Ethernet Controller
* 82573V Gigabit Ethernet Controller (Copper)
* 82573E Gigabit Ethernet Controller (Copper)
* 82573L Gigabit Ethernet Controller
+ * 82574L Gigabit Network Connection
+ * 82583V Gigabit Network Connection
*/
-#include <linux/netdevice.h>
-#include <linux/delay.h>
-#include <linux/pci.h>
-
#include "e1000.h"
#define ID_LED_RESERVED_F746 0xF746
#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
+
static s32 e1000_get_phy_id_82571(struct e1000_hw *hw);
static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw);
static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw);
static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
u16 words, u16 *data);
static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw);
static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw);
static s32 e1000_setup_link_82571(struct e1000_hw *hw);
static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw);
+static void e1000_clear_vfta_82571(struct e1000_hw *hw);
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw);
+static s32 e1000_led_on_82574(struct e1000_hw *hw);
+static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw);
+static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw);
/**
* e1000_init_phy_params_82571 - Init PHY func ptrs.
* @hw: pointer to the HW structure
- *
- * This is a function pointer entry point called by the api module.
**/
static s32 e1000_init_phy_params_82571(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val;
- if (hw->media_type != e1000_media_type_copper) {
+ if (hw->phy.media_type != e1000_media_type_copper) {
phy->type = e1000_phy_none;
return 0;
}
phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
phy->reset_delay_us = 100;
+ phy->ops.power_up = e1000_power_up_phy_copper;
+ phy->ops.power_down = e1000_power_down_phy_copper_82571;
+
switch (hw->mac.type) {
case e1000_82571:
case e1000_82572:
case e1000_82573:
phy->type = e1000_phy_m88;
break;
+ case e1000_82574:
+ case e1000_82583:
+ phy->type = e1000_phy_bm;
+ break;
default:
return -E1000_ERR_PHY;
break;
if (phy->id != M88E1111_I_PHY_ID)
return -E1000_ERR_PHY;
break;
+ case e1000_82574:
+ case e1000_82583:
+ if (phy->id != BME1000_E_PHY_ID_R2)
+ return -E1000_ERR_PHY;
+ break;
default:
return -E1000_ERR_PHY;
break;
/**
* e1000_init_nvm_params_82571 - Init NVM func ptrs.
* @hw: pointer to the HW structure
- *
- * This is a function pointer entry point called by the api module.
**/
static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw)
{
switch (hw->mac.type) {
case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
if (((eecd >> 15) & 0x3) == 0x3) {
nvm->type = e1000_nvm_flash_hw;
nvm->word_size = 2048;
- /* Autonomous Flash update bit must be cleared due
+ /*
+ * Autonomous Flash update bit must be cleared due
* to Flash update issue.
*/
eecd &= ~E1000_EECD_AUPDEN;
}
/* Fall Through */
default:
- nvm->type = e1000_nvm_eeprom_spi;
+ nvm->type = e1000_nvm_eeprom_spi;
size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
E1000_EECD_SIZE_EX_SHIFT);
- /* Added to a constant, "size" becomes the left-shift value
+ /*
+ * Added to a constant, "size" becomes the left-shift value
* for setting word_size.
*/
size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* EEPROM access above 16k is unsupported */
+ if (size > 14)
+ size = 14;
nvm->word_size = 1 << size;
break;
}
/**
* e1000_init_mac_params_82571 - Init MAC func ptrs.
* @hw: pointer to the HW structure
- *
- * This is a function pointer entry point called by the api module.
**/
static s32 e1000_init_mac_params_82571(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
struct e1000_mac_info *mac = &hw->mac;
struct e1000_mac_operations *func = &mac->ops;
+ u32 swsm = 0;
+ u32 swsm2 = 0;
+ bool force_clear_smbi = false;
/* Set media type */
switch (adapter->pdev->device) {
case E1000_DEV_ID_82571EB_FIBER:
case E1000_DEV_ID_82572EI_FIBER:
case E1000_DEV_ID_82571EB_QUAD_FIBER:
- hw->media_type = e1000_media_type_fiber;
+ hw->phy.media_type = e1000_media_type_fiber;
break;
case E1000_DEV_ID_82571EB_SERDES:
case E1000_DEV_ID_82572EI_SERDES:
- hw->media_type = e1000_media_type_internal_serdes;
+ case E1000_DEV_ID_82571EB_SERDES_DUAL:
+ case E1000_DEV_ID_82571EB_SERDES_QUAD:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
break;
default:
- hw->media_type = e1000_media_type_copper;
+ hw->phy.media_type = e1000_media_type_copper;
break;
}
/* Set rar entry count */
mac->rar_entry_count = E1000_RAR_ENTRIES;
/* Set if manageability features are enabled. */
- mac->arc_subsystem_valid =
- (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
+ mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK)
+ ? true : false;
+ /* Adaptive IFS supported */
+ mac->adaptive_ifs = true;
/* check for link */
- switch (hw->media_type) {
+ switch (hw->phy.media_type) {
case e1000_media_type_copper:
func->setup_physical_interface = e1000_setup_copper_link_82571;
func->check_for_link = e1000e_check_for_copper_link;
func->get_link_up_info = e1000e_get_speed_and_duplex_copper;
break;
case e1000_media_type_fiber:
- func->setup_physical_interface = e1000_setup_fiber_serdes_link_82571;
+ func->setup_physical_interface =
+ e1000_setup_fiber_serdes_link_82571;
func->check_for_link = e1000e_check_for_fiber_link;
- func->get_link_up_info = e1000e_get_speed_and_duplex_fiber_serdes;
+ func->get_link_up_info =
+ e1000e_get_speed_and_duplex_fiber_serdes;
break;
case e1000_media_type_internal_serdes:
- func->setup_physical_interface = e1000_setup_fiber_serdes_link_82571;
- func->check_for_link = e1000e_check_for_serdes_link;
- func->get_link_up_info = e1000e_get_speed_and_duplex_fiber_serdes;
+ func->setup_physical_interface =
+ e1000_setup_fiber_serdes_link_82571;
+ func->check_for_link = e1000_check_for_serdes_link_82571;
+ func->get_link_up_info =
+ e1000e_get_speed_and_duplex_fiber_serdes;
break;
default:
return -E1000_ERR_CONFIG;
break;
}
+ switch (hw->mac.type) {
+ case e1000_82573:
+ func->set_lan_id = e1000_set_lan_id_single_port;
+ func->check_mng_mode = e1000e_check_mng_mode_generic;
+ func->led_on = e1000e_led_on_generic;
+ break;
+ case e1000_82574:
+ case e1000_82583:
+ func->set_lan_id = e1000_set_lan_id_single_port;
+ func->check_mng_mode = e1000_check_mng_mode_82574;
+ func->led_on = e1000_led_on_82574;
+ break;
+ default:
+ func->check_mng_mode = e1000e_check_mng_mode_generic;
+ func->led_on = e1000e_led_on_generic;
+ break;
+ }
+
+ /*
+ * Ensure that the inter-port SWSM.SMBI lock bit is clear before
+ * first NVM or PHY acess. This should be done for single-port
+ * devices, and for one port only on dual-port devices so that
+ * for those devices we can still use the SMBI lock to synchronize
+ * inter-port accesses to the PHY & NVM.
+ */
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ swsm2 = er32(SWSM2);
+
+ if (!(swsm2 & E1000_SWSM2_LOCK)) {
+ /* Only do this for the first interface on this card */
+ ew32(SWSM2,
+ swsm2 | E1000_SWSM2_LOCK);
+ force_clear_smbi = true;
+ } else
+ force_clear_smbi = false;
+ break;
+ default:
+ force_clear_smbi = true;
+ break;
+ }
+
+ if (force_clear_smbi) {
+ /* Make sure SWSM.SMBI is clear */
+ swsm = er32(SWSM);
+ if (swsm & E1000_SWSM_SMBI) {
+ /* This bit should not be set on a first interface, and
+ * indicates that the bootagent or EFI code has
+ * improperly left this bit enabled
+ */
+ e_dbg("Please update your 82571 Bootagent\n");
+ }
+ ew32(SWSM, swsm & ~E1000_SWSM_SMBI);
+ }
+
+ /*
+ * Initialze device specific counter of SMBI acquisition
+ * timeouts.
+ */
+ hw->dev_spec.e82571.smb_counter = 0;
+
return 0;
}
-static s32 e1000_get_invariants_82571(struct e1000_adapter *adapter)
+static s32 e1000_get_variants_82571(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
static int global_quad_port_a; /* global port a indication */
case E1000_DEV_ID_82571EB_QUAD_COPPER:
case E1000_DEV_ID_82571EB_QUAD_FIBER:
case E1000_DEV_ID_82571EB_QUAD_COPPER_LP:
+ case E1000_DEV_ID_82571PT_QUAD_COPPER:
adapter->flags |= FLAG_IS_QUAD_PORT;
/* mark the first port */
if (global_quad_port_a == 0)
if (adapter->flags & FLAG_IS_QUAD_PORT &&
(!(adapter->flags & FLAG_IS_QUAD_PORT_A)))
adapter->flags &= ~FLAG_HAS_WOL;
+ /* Does not support WoL on any port */
+ if (pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD)
+ adapter->flags &= ~FLAG_HAS_WOL;
break;
case e1000_82573:
if (pdev->device == E1000_DEV_ID_82573L) {
- e1000_read_nvm(&adapter->hw, NVM_INIT_3GIO_3, 1,
- &eeprom_data);
- if (eeprom_data & NVM_WORD1A_ASPM_MASK)
- adapter->flags &= ~FLAG_HAS_JUMBO_FRAMES;
+ if (e1000_read_nvm(&adapter->hw, NVM_INIT_3GIO_3, 1,
+ &eeprom_data) < 0)
+ break;
+ if (!(eeprom_data & NVM_WORD1A_ASPM_MASK)) {
+ adapter->flags |= FLAG_HAS_JUMBO_FRAMES;
+ adapter->max_hw_frame_size = DEFAULT_JUMBO;
+ }
}
break;
default:
static s32 e1000_get_phy_id_82571(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_id = 0;
switch (hw->mac.type) {
case e1000_82571:
case e1000_82572:
- /* The 82571 firmware may still be configuring the PHY.
+ /*
+ * The 82571 firmware may still be configuring the PHY.
* In this case, we cannot access the PHY until the
* configuration is done. So we explicitly set the
- * PHY ID. */
+ * PHY ID.
+ */
phy->id = IGP01E1000_I_PHY_ID;
break;
case e1000_82573:
return e1000e_get_phy_id(hw);
break;
+ case e1000_82574:
+ case e1000_82583:
+ ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ if (ret_val)
+ return ret_val;
+
+ phy->id = (u32)(phy_id << 16);
+ udelay(20);
+ ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ if (ret_val)
+ return ret_val;
+
+ phy->id |= (u32)(phy_id);
+ phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+ break;
default:
return -E1000_ERR_PHY;
break;
static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw)
{
u32 swsm;
- s32 timeout = hw->nvm.word_size + 1;
+ s32 sw_timeout = hw->nvm.word_size + 1;
+ s32 fw_timeout = hw->nvm.word_size + 1;
s32 i = 0;
+ /*
+ * If we have timedout 3 times on trying to acquire
+ * the inter-port SMBI semaphore, there is old code
+ * operating on the other port, and it is not
+ * releasing SMBI. Modify the number of times that
+ * we try for the semaphore to interwork with this
+ * older code.
+ */
+ if (hw->dev_spec.e82571.smb_counter > 2)
+ sw_timeout = 1;
+
+ /* Get the SW semaphore */
+ while (i < sw_timeout) {
+ swsm = er32(SWSM);
+ if (!(swsm & E1000_SWSM_SMBI))
+ break;
+
+ udelay(50);
+ i++;
+ }
+
+ if (i == sw_timeout) {
+ e_dbg("Driver can't access device - SMBI bit is set.\n");
+ hw->dev_spec.e82571.smb_counter++;
+ }
/* Get the FW semaphore. */
- for (i = 0; i < timeout; i++) {
+ for (i = 0; i < fw_timeout; i++) {
swsm = er32(SWSM);
ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
udelay(50);
}
- if (i == timeout) {
+ if (i == fw_timeout) {
/* Release semaphores */
- e1000e_put_hw_semaphore(hw);
- hw_dbg(hw, "Driver can't access the NVM\n");
+ e1000_put_hw_semaphore_82571(hw);
+ e_dbg("Driver can't access the NVM\n");
return -E1000_ERR_NVM;
}
u32 swsm;
swsm = er32(SWSM);
-
- swsm &= ~E1000_SWSM_SWESMBI;
-
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
ew32(SWSM, swsm);
}
if (ret_val)
return ret_val;
- if (hw->mac.type != e1000_82573)
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
+ break;
+ default:
ret_val = e1000e_acquire_nvm(hw);
+ break;
+ }
if (ret_val)
e1000_put_hw_semaphore_82571(hw);
* For non-82573 silicon, write data to EEPROM at offset using SPI interface.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
u16 *data)
switch (hw->mac.type) {
case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data);
break;
case e1000_82571:
if (ret_val)
return ret_val;
- /* If our nvm is an EEPROM, then we're done
- * otherwise, commit the checksum to the flash NVM. */
+ /*
+ * If our nvm is an EEPROM, then we're done
+ * otherwise, commit the checksum to the flash NVM.
+ */
if (hw->nvm.type != e1000_nvm_flash_hw)
return ret_val;
/* Reset the firmware if using STM opcode. */
if ((er32(FLOP) & 0xFF00) == E1000_STM_OPCODE) {
- /* The enabling of and the actual reset must be done
+ /*
+ * The enabling of and the actual reset must be done
* in two write cycles.
*/
ew32(HICR, E1000_HICR_FW_RESET_ENABLE);
* poll for completion.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
u16 words, u16 *data)
{
struct e1000_nvm_info *nvm = &hw->nvm;
- u32 i;
- u32 eewr = 0;
+ u32 i, eewr = 0;
s32 ret_val = 0;
- /* A check for invalid values: offset too large, too many words,
- * and not enough words. */
+ /*
+ * A check for invalid values: offset too large, too many words,
+ * and not enough words.
+ */
if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
(words == 0)) {
- hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ e_dbg("nvm parameter(s) out of bounds\n");
return -E1000_ERR_NVM;
}
timeout--;
}
if (!timeout) {
- hw_dbg(hw, "MNG configuration cycle has not completed.\n");
+ e_dbg("MNG configuration cycle has not completed.\n");
return -E1000_ERR_RESET;
}
/**
* e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state
* @hw: pointer to the HW structure
- * @active: TRUE to enable LPLU, FALSE to disable
+ * @active: true to enable LPLU, false to disable
*
* Sets the LPLU D0 state according to the active flag. When activating LPLU
* this function also disables smart speed and vice versa. LPLU will not be
} else {
data &= ~IGP02E1000_PM_D0_LPLU;
ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
- /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
* during Dx states where the power conservation is most
* important. During driver activity we should enable
- * SmartSpeed, so performance is maintained. */
+ * SmartSpeed, so performance is maintained.
+ */
if (phy->smart_speed == e1000_smart_speed_on) {
ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- &data);
+ &data);
if (ret_val)
return ret_val;
data |= IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- data);
+ data);
if (ret_val)
return ret_val;
} else if (phy->smart_speed == e1000_smart_speed_off) {
ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- &data);
+ &data);
if (ret_val)
return ret_val;
data &= ~IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- data);
+ data);
if (ret_val)
return ret_val;
}
* e1000_reset_hw_82571 - Reset hardware
* @hw: pointer to the HW structure
*
- * This resets the hardware into a known state. This is a
- * function pointer entry point called by the api module.
+ * This resets the hardware into a known state.
**/
static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
{
- u32 ctrl;
- u32 extcnf_ctrl;
- u32 ctrl_ext;
- u32 icr;
+ u32 ctrl, extcnf_ctrl, ctrl_ext, icr;
s32 ret_val;
u16 i = 0;
- /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
* on the last TLP read/write transaction when MAC is reset.
*/
ret_val = e1000e_disable_pcie_master(hw);
if (ret_val)
- hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
+ e_dbg("PCI-E Master disable polling has failed.\n");
- hw_dbg(hw, "Masking off all interrupts\n");
+ e_dbg("Masking off all interrupts\n");
ew32(IMC, 0xffffffff);
ew32(RCTL, 0);
msleep(10);
- /* Must acquire the MDIO ownership before MAC reset.
- * Ownership defaults to firmware after a reset. */
- if (hw->mac.type == e1000_82573) {
+ /*
+ * Must acquire the MDIO ownership before MAC reset.
+ * Ownership defaults to firmware after a reset.
+ */
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
extcnf_ctrl = er32(EXTCNF_CTRL);
extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
msleep(2);
i++;
} while (i < MDIO_OWNERSHIP_TIMEOUT);
+ break;
+ default:
+ break;
}
ctrl = er32(CTRL);
- hw_dbg(hw, "Issuing a global reset to MAC\n");
+ e_dbg("Issuing a global reset to MAC\n");
ew32(CTRL, ctrl | E1000_CTRL_RST);
if (hw->nvm.type == e1000_nvm_flash_hw) {
/* We don't want to continue accessing MAC registers. */
return ret_val;
- /* Phy configuration from NVM just starts after EECD_AUTO_RD is set.
+ /*
+ * Phy configuration from NVM just starts after EECD_AUTO_RD is set.
* Need to wait for Phy configuration completion before accessing
* NVM and Phy.
*/
- if (hw->mac.type == e1000_82573)
+
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
msleep(25);
+ break;
+ default:
+ break;
+ }
/* Clear any pending interrupt events. */
ew32(IMC, 0xffffffff);
icr = er32(ICR);
- if (hw->mac.type == e1000_82571 &&
- hw->dev_spec.e82571.alt_mac_addr_is_present)
- e1000e_set_laa_state_82571(hw, true);
+ /* Install any alternate MAC address into RAR0 */
+ ret_val = e1000_check_alt_mac_addr_generic(hw);
+ if (ret_val)
+ return ret_val;
+
+ e1000e_set_laa_state_82571(hw, true);
+
+ /* Reinitialize the 82571 serdes link state machine */
+ if (hw->phy.media_type == e1000_media_type_internal_serdes)
+ hw->mac.serdes_link_state = e1000_serdes_link_down;
return 0;
}
struct e1000_mac_info *mac = &hw->mac;
u32 reg_data;
s32 ret_val;
- u16 i;
- u16 rar_count = mac->rar_entry_count;
+ u16 i, rar_count = mac->rar_entry_count;
e1000_initialize_hw_bits_82571(hw);
/* Initialize identification LED */
ret_val = e1000e_id_led_init(hw);
- if (ret_val) {
- hw_dbg(hw, "Error initializing identification LED\n");
- return ret_val;
- }
+ if (ret_val)
+ e_dbg("Error initializing identification LED\n");
+ /* This is not fatal and we should not stop init due to this */
/* Disabling VLAN filtering */
- hw_dbg(hw, "Initializing the IEEE VLAN\n");
- e1000e_clear_vfta(hw);
+ e_dbg("Initializing the IEEE VLAN\n");
+ mac->ops.clear_vfta(hw);
/* Setup the receive address. */
- /* If, however, a locally administered address was assigned to the
+ /*
+ * If, however, a locally administered address was assigned to the
* 82571, we must reserve a RAR for it to work around an issue where
* resetting one port will reload the MAC on the other port.
*/
e1000e_init_rx_addrs(hw, rar_count);
/* Zero out the Multicast HASH table */
- hw_dbg(hw, "Zeroing the MTA\n");
+ e_dbg("Zeroing the MTA\n");
for (i = 0; i < mac->mta_reg_count; i++)
E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
ret_val = e1000_setup_link_82571(hw);
/* Set the transmit descriptor write-back policy */
- reg_data = er32(TXDCTL);
+ reg_data = er32(TXDCTL(0));
reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
E1000_TXDCTL_FULL_TX_DESC_WB |
E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL, reg_data);
+ ew32(TXDCTL(0), reg_data);
/* ...for both queues. */
- if (mac->type != e1000_82573) {
- reg_data = er32(TXDCTL1);
- reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
- E1000_TXDCTL_FULL_TX_DESC_WB |
- E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL1, reg_data);
- } else {
+ switch (mac->type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
e1000e_enable_tx_pkt_filtering(hw);
reg_data = er32(GCR);
reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
ew32(GCR, reg_data);
+ break;
+ default:
+ reg_data = er32(TXDCTL(1));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB |
+ E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(1), reg_data);
+ break;
}
- /* Clear all of the statistics registers (clear on read). It is
+ /*
+ * Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
* is no link.
u32 reg;
/* Transmit Descriptor Control 0 */
- reg = er32(TXDCTL);
+ reg = er32(TXDCTL(0));
reg |= (1 << 22);
- ew32(TXDCTL, reg);
+ ew32(TXDCTL(0), reg);
/* Transmit Descriptor Control 1 */
- reg = er32(TXDCTL1);
+ reg = er32(TXDCTL(1));
reg |= (1 << 22);
- ew32(TXDCTL1, reg);
+ ew32(TXDCTL(1), reg);
/* Transmit Arbitration Control 0 */
- reg = er32(TARC0);
+ reg = er32(TARC(0));
reg &= ~(0xF << 27); /* 30:27 */
switch (hw->mac.type) {
case e1000_82571:
default:
break;
}
- ew32(TARC0, reg);
+ ew32(TARC(0), reg);
/* Transmit Arbitration Control 1 */
- reg = er32(TARC1);
+ reg = er32(TARC(1));
switch (hw->mac.type) {
case e1000_82571:
case e1000_82572:
reg &= ~(1 << 28);
else
reg |= (1 << 28);
- ew32(TARC1, reg);
+ ew32(TARC(1), reg);
break;
default:
break;
}
/* Device Control */
- if (hw->mac.type == e1000_82573) {
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
reg = er32(CTRL);
reg &= ~(1 << 29);
ew32(CTRL, reg);
+ break;
+ default:
+ break;
}
/* Extended Device Control */
- if (hw->mac.type == e1000_82573) {
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
reg = er32(CTRL_EXT);
reg &= ~(1 << 23);
reg |= (1 << 22);
ew32(CTRL_EXT, reg);
+ break;
+ default:
+ break;
}
+
+ if (hw->mac.type == e1000_82571) {
+ reg = er32(PBA_ECC);
+ reg |= E1000_PBA_ECC_CORR_EN;
+ ew32(PBA_ECC, reg);
+ }
+ /*
+ * Workaround for hardware errata.
+ * Ensure that DMA Dynamic Clock gating is disabled on 82571 and 82572
+ */
+
+ if ((hw->mac.type == e1000_82571) ||
+ (hw->mac.type == e1000_82572)) {
+ reg = er32(CTRL_EXT);
+ reg &= ~E1000_CTRL_EXT_DMA_DYN_CLK_EN;
+ ew32(CTRL_EXT, reg);
+ }
+
+
+ /* PCI-Ex Control Registers */
+ switch (hw->mac.type) {
+ case e1000_82574:
+ case e1000_82583:
+ reg = er32(GCR);
+ reg |= (1 << 22);
+ ew32(GCR, reg);
+
+ /*
+ * Workaround for hardware errata.
+ * apply workaround for hardware errata documented in errata
+ * docs Fixes issue where some error prone or unreliable PCIe
+ * completions are occurring, particularly with ASPM enabled.
+ * Without fix, issue can cause tx timeouts.
+ */
+ reg = er32(GCR2);
+ reg |= 1;
+ ew32(GCR2, reg);
+ break;
+ default:
+ break;
+ }
+
+ return;
}
/**
- * e1000e_clear_vfta - Clear VLAN filter table
+ * e1000_clear_vfta_82571 - Clear VLAN filter table
* @hw: pointer to the HW structure
*
* Clears the register array which contains the VLAN filter table by
* setting all the values to 0.
**/
-void e1000e_clear_vfta(struct e1000_hw *hw)
+static void e1000_clear_vfta_82571(struct e1000_hw *hw)
{
u32 offset;
u32 vfta_value = 0;
u32 vfta_offset = 0;
u32 vfta_bit_in_reg = 0;
- if (hw->mac.type == e1000_82573) {
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
if (hw->mng_cookie.vlan_id != 0) {
- /* The VFTA is a 4096b bit-field, each identifying
+ /*
+ * The VFTA is a 4096b bit-field, each identifying
* a single VLAN ID. The following operations
* determine which 32b entry (i.e. offset) into the
* array we want to set the VLAN ID (i.e. bit) of
vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
}
+ break;
+ default:
+ break;
}
for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
- /* If the offset we want to clear is the same offset of the
+ /*
+ * If the offset we want to clear is the same offset of the
* manageability VLAN ID, then clear all bits except that of
* the manageability unit.
*/
}
/**
- * e1000_mc_addr_list_update_82571 - Update Multicast addresses
+ * e1000_check_mng_mode_82574 - Check manageability is enabled
* @hw: pointer to the HW structure
- * @mc_addr_list: array of multicast addresses to program
- * @mc_addr_count: number of multicast addresses to program
- * @rar_used_count: the first RAR register free to program
- * @rar_count: total number of supported Receive Address Registers
*
- * Updates the Receive Address Registers and Multicast Table Array.
- * The caller must have a packed mc_addr_list of multicast addresses.
- * The parameter rar_count will usually be hw->mac.rar_entry_count
- * unless there are workarounds that change this.
+ * Reads the NVM Initialization Control Word 2 and returns true
+ * (>0) if any manageability is enabled, else false (0).
**/
-static void e1000_mc_addr_list_update_82571(struct e1000_hw *hw,
- u8 *mc_addr_list,
- u32 mc_addr_count,
- u32 rar_used_count,
- u32 rar_count)
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw)
{
- if (e1000e_get_laa_state_82571(hw))
- rar_count--;
+ u16 data;
+
+ e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &data);
+ return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0;
+}
+
+/**
+ * e1000_led_on_82574 - Turn LED on
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED on.
+ **/
+static s32 e1000_led_on_82574(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 i;
+
+ ctrl = hw->mac.ledctl_mode2;
+ if (!(E1000_STATUS_LU & er32(STATUS))) {
+ /*
+ * If no link, then turn LED on by setting the invert bit
+ * for each LED that's "on" (0x0E) in ledctl_mode2.
+ */
+ for (i = 0; i < 4; i++)
+ if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+ E1000_LEDCTL_MODE_LED_ON)
+ ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8));
+ }
+ ew32(LEDCTL, ctrl);
- e1000e_mc_addr_list_update_generic(hw, mc_addr_list, mc_addr_count,
- rar_used_count, rar_count);
+ return 0;
}
/**
**/
static s32 e1000_setup_link_82571(struct e1000_hw *hw)
{
- /* 82573 does not have a word in the NVM to determine
+ /*
+ * 82573 does not have a word in the NVM to determine
* the default flow control setting, so we explicitly
* set it to full.
*/
- if (hw->mac.type == e1000_82573)
- hw->mac.fc = e1000_fc_full;
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
+ if (hw->fc.requested_mode == e1000_fc_default)
+ hw->fc.requested_mode = e1000_fc_full;
+ break;
+ default:
+ break;
+ }
return e1000e_setup_link(hw);
}
static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw)
{
u32 ctrl;
- u32 led_ctrl;
s32 ret_val;
ctrl = er32(CTRL);
switch (hw->phy.type) {
case e1000_phy_m88:
+ case e1000_phy_bm:
ret_val = e1000e_copper_link_setup_m88(hw);
break;
case e1000_phy_igp_2:
ret_val = e1000e_copper_link_setup_igp(hw);
- /* Setup activity LED */
- led_ctrl = er32(LEDCTL);
- led_ctrl &= IGP_ACTIVITY_LED_MASK;
- led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
- ew32(LEDCTL, led_ctrl);
break;
default:
return -E1000_ERR_PHY;
switch (hw->mac.type) {
case e1000_82571:
case e1000_82572:
- /* If SerDes loopback mode is entered, there is no form
+ /*
+ * If SerDes loopback mode is entered, there is no form
* of reset to take the adapter out of that mode. So we
* have to explicitly take the adapter out of loopback
- * mode. This prevents drivers from twidling their thumbs
+ * mode. This prevents drivers from twiddling their thumbs
* if another tool failed to take it out of loopback mode.
*/
- ew32(SCTL,
- E1000_SCTL_DISABLE_SERDES_LOOPBACK);
+ ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
break;
default:
break;
}
/**
+ * e1000_check_for_serdes_link_82571 - Check for link (Serdes)
+ * @hw: pointer to the HW structure
+ *
+ * Reports the link state as up or down.
+ *
+ * If autonegotiation is supported by the link partner, the link state is
+ * determined by the result of autonegotiation. This is the most likely case.
+ * If autonegotiation is not supported by the link partner, and the link
+ * has a valid signal, force the link up.
+ *
+ * The link state is represented internally here by 4 states:
+ *
+ * 1) down
+ * 2) autoneg_progress
+ * 3) autoneg_complete (the link successfully autonegotiated)
+ * 4) forced_up (the link has been forced up, it did not autonegotiate)
+ *
+ **/
+static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val = 0;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) {
+
+ /* Receiver is synchronized with no invalid bits. */
+ switch (mac->serdes_link_state) {
+ case e1000_serdes_link_autoneg_complete:
+ if (!(status & E1000_STATUS_LU)) {
+ /*
+ * We have lost link, retry autoneg before
+ * reporting link failure
+ */
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_progress;
+ mac->serdes_has_link = false;
+ e_dbg("AN_UP -> AN_PROG\n");
+ }
+ break;
+
+ case e1000_serdes_link_forced_up:
+ /*
+ * If we are receiving /C/ ordered sets, re-enable
+ * auto-negotiation in the TXCW register and disable
+ * forced link in the Device Control register in an
+ * attempt to auto-negotiate with our link partner.
+ */
+ if (rxcw & E1000_RXCW_C) {
+ /* Enable autoneg, and unforce link up */
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_progress;
+ mac->serdes_has_link = false;
+ e_dbg("FORCED_UP -> AN_PROG\n");
+ }
+ break;
+
+ case e1000_serdes_link_autoneg_progress:
+ if (rxcw & E1000_RXCW_C) {
+ /*
+ * We received /C/ ordered sets, meaning the
+ * link partner has autonegotiated, and we can
+ * trust the Link Up (LU) status bit.
+ */
+ if (status & E1000_STATUS_LU) {
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_complete;
+ e_dbg("AN_PROG -> AN_UP\n");
+ mac->serdes_has_link = true;
+ } else {
+ /* Autoneg completed, but failed. */
+ mac->serdes_link_state =
+ e1000_serdes_link_down;
+ e_dbg("AN_PROG -> DOWN\n");
+ }
+ } else {
+ /*
+ * The link partner did not autoneg.
+ * Force link up and full duplex, and change
+ * state to forced.
+ */
+ ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after link up. */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ e_dbg("Error config flow control\n");
+ break;
+ }
+ mac->serdes_link_state =
+ e1000_serdes_link_forced_up;
+ mac->serdes_has_link = true;
+ e_dbg("AN_PROG -> FORCED_UP\n");
+ }
+ break;
+
+ case e1000_serdes_link_down:
+ default:
+ /*
+ * The link was down but the receiver has now gained
+ * valid sync, so lets see if we can bring the link
+ * up.
+ */
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+ mac->serdes_link_state =
+ e1000_serdes_link_autoneg_progress;
+ e_dbg("DOWN -> AN_PROG\n");
+ break;
+ }
+ } else {
+ if (!(rxcw & E1000_RXCW_SYNCH)) {
+ mac->serdes_has_link = false;
+ mac->serdes_link_state = e1000_serdes_link_down;
+ e_dbg("ANYSTATE -> DOWN\n");
+ } else {
+ /*
+ * We have sync, and can tolerate one invalid (IV)
+ * codeword before declaring link down, so reread
+ * to look again.
+ */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_IV) {
+ mac->serdes_link_state = e1000_serdes_link_down;
+ mac->serdes_has_link = false;
+ e_dbg("ANYSTATE -> DOWN\n");
+ }
+ }
+ }
+
+ return ret_val;
+}
+
+/**
* e1000_valid_led_default_82571 - Verify a valid default LED config
* @hw: pointer to the HW structure
* @data: pointer to the NVM (EEPROM)
ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
- if (hw->mac.type == e1000_82573 &&
- *data == ID_LED_RESERVED_F746)
- *data = ID_LED_DEFAULT_82573;
- else if (*data == ID_LED_RESERVED_0000 ||
- *data == ID_LED_RESERVED_FFFF)
- *data = ID_LED_DEFAULT;
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_82583:
+ if (*data == ID_LED_RESERVED_F746)
+ *data = ID_LED_DEFAULT_82573;
+ break;
+ default:
+ if (*data == ID_LED_RESERVED_0000 ||
+ *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT;
+ break;
+ }
return 0;
}
* e1000e_get_laa_state_82571 - Get locally administered address state
* @hw: pointer to the HW structure
*
- * Retrieve and return the current locally administed address state.
+ * Retrieve and return the current locally administered address state.
**/
bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
{
if (hw->mac.type != e1000_82571)
- return 0;
+ return false;
return hw->dev_spec.e82571.laa_is_present;
}
* @hw: pointer to the HW structure
* @state: enable/disable locally administered address
*
- * Enable/Disable the current locally administed address state.
+ * Enable/Disable the current locally administered address state.
**/
void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
{
/* If workaround is activated... */
if (state)
- /* Hold a copy of the LAA in RAR[14] This is done so that
+ /*
+ * Hold a copy of the LAA in RAR[14] This is done so that
* between the time RAR[0] gets clobbered and the time it
* gets fixed, the actual LAA is in one of the RARs and no
* incoming packets directed to this port are dropped.
if (nvm->type != e1000_nvm_flash_hw)
return 0;
- /* Check bit 4 of word 10h. If it is 0, firmware is done updating
+ /*
+ * Check bit 4 of word 10h. If it is 0, firmware is done updating
* 10h-12h. Checksum may need to be fixed.
*/
ret_val = e1000_read_nvm(hw, 0x10, 1, &data);
return ret_val;
if (!(data & 0x10)) {
- /* Read 0x23 and check bit 15. This bit is a 1
+ /*
+ * Read 0x23 and check bit 15. This bit is a 1
* when the checksum has already been fixed. If
* the checksum is still wrong and this bit is a
* 1, we need to return bad checksum. Otherwise,
}
/**
+ * e1000_read_mac_addr_82571 - Read device MAC address
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+
+ /*
+ * If there's an alternate MAC address place it in RAR0
+ * so that it will override the Si installed default perm
+ * address.
+ */
+ ret_val = e1000_check_alt_mac_addr_generic(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000_read_mac_addr_generic(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_power_down_phy_copper_82571 - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ **/
+static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ struct e1000_mac_info *mac = &hw->mac;
+
+ if (!(phy->ops.check_reset_block))
+ return;
+
+ /* If the management interface is not enabled, then power down */
+ if (!(mac->ops.check_mng_mode(hw) || phy->ops.check_reset_block(hw)))
+ e1000_power_down_phy_copper(hw);
+
+ return;
+}
+
+/**
* e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters
* @hw: pointer to the HW structure
*
**/
static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw)
{
- u32 temp;
-
e1000e_clear_hw_cntrs_base(hw);
- temp = er32(PRC64);
- temp = er32(PRC127);
- temp = er32(PRC255);
- temp = er32(PRC511);
- temp = er32(PRC1023);
- temp = er32(PRC1522);
- temp = er32(PTC64);
- temp = er32(PTC127);
- temp = er32(PTC255);
- temp = er32(PTC511);
- temp = er32(PTC1023);
- temp = er32(PTC1522);
-
- temp = er32(ALGNERRC);
- temp = er32(RXERRC);
- temp = er32(TNCRS);
- temp = er32(CEXTERR);
- temp = er32(TSCTC);
- temp = er32(TSCTFC);
-
- temp = er32(MGTPRC);
- temp = er32(MGTPDC);
- temp = er32(MGTPTC);
-
- temp = er32(IAC);
- temp = er32(ICRXOC);
-
- temp = er32(ICRXPTC);
- temp = er32(ICRXATC);
- temp = er32(ICTXPTC);
- temp = er32(ICTXATC);
- temp = er32(ICTXQEC);
- temp = er32(ICTXQMTC);
- temp = er32(ICRXDMTC);
+ er32(PRC64);
+ er32(PRC127);
+ er32(PRC255);
+ er32(PRC511);
+ er32(PRC1023);
+ er32(PRC1522);
+ er32(PTC64);
+ er32(PTC127);
+ er32(PTC255);
+ er32(PTC511);
+ er32(PTC1023);
+ er32(PTC1522);
+
+ er32(ALGNERRC);
+ er32(RXERRC);
+ er32(TNCRS);
+ er32(CEXTERR);
+ er32(TSCTC);
+ er32(TSCTFC);
+
+ er32(MGTPRC);
+ er32(MGTPDC);
+ er32(MGTPTC);
+
+ er32(IAC);
+ er32(ICRXOC);
+
+ er32(ICRXPTC);
+ er32(ICRXATC);
+ er32(ICTXPTC);
+ er32(ICTXATC);
+ er32(ICTXQEC);
+ er32(ICTXQMTC);
+ er32(ICRXDMTC);
}
static struct e1000_mac_operations e82571_mac_ops = {
- .mng_mode_enab = E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT,
+ /* .check_mng_mode: mac type dependent */
/* .check_for_link: media type dependent */
+ .id_led_init = e1000e_id_led_init,
.cleanup_led = e1000e_cleanup_led_generic,
.clear_hw_cntrs = e1000_clear_hw_cntrs_82571,
.get_bus_info = e1000e_get_bus_info_pcie,
+ .set_lan_id = e1000_set_lan_id_multi_port_pcie,
/* .get_link_up_info: media type dependent */
- .led_on = e1000e_led_on_generic,
+ /* .led_on: mac type dependent */
.led_off = e1000e_led_off_generic,
- .mc_addr_list_update = e1000_mc_addr_list_update_82571,
+ .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
+ .write_vfta = e1000_write_vfta_generic,
+ .clear_vfta = e1000_clear_vfta_82571,
.reset_hw = e1000_reset_hw_82571,
.init_hw = e1000_init_hw_82571,
.setup_link = e1000_setup_link_82571,
/* .setup_physical_interface: media type dependent */
+ .setup_led = e1000e_setup_led_generic,
+ .read_mac_addr = e1000_read_mac_addr_82571,
};
static struct e1000_phy_operations e82_phy_ops_igp = {
- .acquire_phy = e1000_get_hw_semaphore_82571,
+ .acquire = e1000_get_hw_semaphore_82571,
+ .check_polarity = e1000_check_polarity_igp,
.check_reset_block = e1000e_check_reset_block_generic,
- .commit_phy = NULL,
+ .commit = NULL,
.force_speed_duplex = e1000e_phy_force_speed_duplex_igp,
.get_cfg_done = e1000_get_cfg_done_82571,
.get_cable_length = e1000e_get_cable_length_igp_2,
- .get_phy_info = e1000e_get_phy_info_igp,
- .read_phy_reg = e1000e_read_phy_reg_igp,
- .release_phy = e1000_put_hw_semaphore_82571,
- .reset_phy = e1000e_phy_hw_reset_generic,
+ .get_info = e1000e_get_phy_info_igp,
+ .read_reg = e1000e_read_phy_reg_igp,
+ .release = e1000_put_hw_semaphore_82571,
+ .reset = e1000e_phy_hw_reset_generic,
.set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
.set_d3_lplu_state = e1000e_set_d3_lplu_state,
- .write_phy_reg = e1000e_write_phy_reg_igp,
+ .write_reg = e1000e_write_phy_reg_igp,
+ .cfg_on_link_up = NULL,
};
static struct e1000_phy_operations e82_phy_ops_m88 = {
- .acquire_phy = e1000_get_hw_semaphore_82571,
+ .acquire = e1000_get_hw_semaphore_82571,
+ .check_polarity = e1000_check_polarity_m88,
.check_reset_block = e1000e_check_reset_block_generic,
- .commit_phy = e1000e_phy_sw_reset,
+ .commit = e1000e_phy_sw_reset,
.force_speed_duplex = e1000e_phy_force_speed_duplex_m88,
.get_cfg_done = e1000e_get_cfg_done,
.get_cable_length = e1000e_get_cable_length_m88,
- .get_phy_info = e1000e_get_phy_info_m88,
- .read_phy_reg = e1000e_read_phy_reg_m88,
- .release_phy = e1000_put_hw_semaphore_82571,
- .reset_phy = e1000e_phy_hw_reset_generic,
+ .get_info = e1000e_get_phy_info_m88,
+ .read_reg = e1000e_read_phy_reg_m88,
+ .release = e1000_put_hw_semaphore_82571,
+ .reset = e1000e_phy_hw_reset_generic,
.set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
.set_d3_lplu_state = e1000e_set_d3_lplu_state,
- .write_phy_reg = e1000e_write_phy_reg_m88,
+ .write_reg = e1000e_write_phy_reg_m88,
+ .cfg_on_link_up = NULL,
};
-static struct e1000_nvm_operations e82571_nvm_ops = {
- .acquire_nvm = e1000_acquire_nvm_82571,
- .read_nvm = e1000e_read_nvm_spi,
- .release_nvm = e1000_release_nvm_82571,
- .update_nvm = e1000_update_nvm_checksum_82571,
- .valid_led_default = e1000_valid_led_default_82571,
- .validate_nvm = e1000_validate_nvm_checksum_82571,
- .write_nvm = e1000_write_nvm_82571,
+static struct e1000_phy_operations e82_phy_ops_bm = {
+ .acquire = e1000_get_hw_semaphore_82571,
+ .check_polarity = e1000_check_polarity_m88,
+ .check_reset_block = e1000e_check_reset_block_generic,
+ .commit = e1000e_phy_sw_reset,
+ .force_speed_duplex = e1000e_phy_force_speed_duplex_m88,
+ .get_cfg_done = e1000e_get_cfg_done,
+ .get_cable_length = e1000e_get_cable_length_m88,
+ .get_info = e1000e_get_phy_info_m88,
+ .read_reg = e1000e_read_phy_reg_bm2,
+ .release = e1000_put_hw_semaphore_82571,
+ .reset = e1000e_phy_hw_reset_generic,
+ .set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
+ .set_d3_lplu_state = e1000e_set_d3_lplu_state,
+ .write_reg = e1000e_write_phy_reg_bm2,
+ .cfg_on_link_up = NULL,
};
-static struct e1000_nvm_operations e82573_nvm_ops = {
- .acquire_nvm = e1000_acquire_nvm_82571,
- .read_nvm = e1000e_read_nvm_eerd,
- .release_nvm = e1000_release_nvm_82571,
- .update_nvm = e1000_update_nvm_checksum_82571,
+static struct e1000_nvm_operations e82571_nvm_ops = {
+ .acquire = e1000_acquire_nvm_82571,
+ .read = e1000e_read_nvm_eerd,
+ .release = e1000_release_nvm_82571,
+ .update = e1000_update_nvm_checksum_82571,
.valid_led_default = e1000_valid_led_default_82571,
- .validate_nvm = e1000_validate_nvm_checksum_82571,
- .write_nvm = e1000_write_nvm_82571,
+ .validate = e1000_validate_nvm_checksum_82571,
+ .write = e1000_write_nvm_82571,
};
struct e1000_info e1000_82571_info = {
.mac = e1000_82571,
.flags = FLAG_HAS_HW_VLAN_FILTER
| FLAG_HAS_JUMBO_FRAMES
- | FLAG_HAS_STATS_PTC_PRC
| FLAG_HAS_WOL
| FLAG_APME_IN_CTRL3
| FLAG_RX_CSUM_ENABLED
| FLAG_HAS_CTRLEXT_ON_LOAD
- | FLAG_HAS_STATS_ICR_ICT
| FLAG_HAS_SMART_POWER_DOWN
| FLAG_RESET_OVERWRITES_LAA /* errata */
| FLAG_TARC_SPEED_MODE_BIT /* errata */
| FLAG_APME_CHECK_PORT_B,
.pba = 38,
- .get_invariants = e1000_get_invariants_82571,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .get_variants = e1000_get_variants_82571,
.mac_ops = &e82571_mac_ops,
.phy_ops = &e82_phy_ops_igp,
.nvm_ops = &e82571_nvm_ops,
.mac = e1000_82572,
.flags = FLAG_HAS_HW_VLAN_FILTER
| FLAG_HAS_JUMBO_FRAMES
- | FLAG_HAS_STATS_PTC_PRC
| FLAG_HAS_WOL
| FLAG_APME_IN_CTRL3
| FLAG_RX_CSUM_ENABLED
| FLAG_HAS_CTRLEXT_ON_LOAD
- | FLAG_HAS_STATS_ICR_ICT
| FLAG_TARC_SPEED_MODE_BIT, /* errata */
.pba = 38,
- .get_invariants = e1000_get_invariants_82571,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .get_variants = e1000_get_variants_82571,
.mac_ops = &e82571_mac_ops,
.phy_ops = &e82_phy_ops_igp,
.nvm_ops = &e82571_nvm_ops,
.mac = e1000_82573,
.flags = FLAG_HAS_HW_VLAN_FILTER
| FLAG_HAS_JUMBO_FRAMES
- | FLAG_HAS_STATS_PTC_PRC
| FLAG_HAS_WOL
| FLAG_APME_IN_CTRL3
| FLAG_RX_CSUM_ENABLED
- | FLAG_HAS_STATS_ICR_ICT
| FLAG_HAS_SMART_POWER_DOWN
| FLAG_HAS_AMT
| FLAG_HAS_ERT
| FLAG_HAS_SWSM_ON_LOAD,
.pba = 20,
- .get_invariants = e1000_get_invariants_82571,
+ .max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN,
+ .get_variants = e1000_get_variants_82571,
.mac_ops = &e82571_mac_ops,
.phy_ops = &e82_phy_ops_m88,
- .nvm_ops = &e82573_nvm_ops,
+ .nvm_ops = &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82574_info = {
+ .mac = e1000_82574,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_MSIX
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_HAS_AMT
+ | FLAG_HAS_CTRLEXT_ON_LOAD,
+ .pba = 20,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .get_variants = e1000_get_variants_82571,
+ .mac_ops = &e82571_mac_ops,
+ .phy_ops = &e82_phy_ops_bm,
+ .nvm_ops = &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82583_info = {
+ .mac = e1000_82583,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_HAS_AMT
+ | FLAG_HAS_CTRLEXT_ON_LOAD,
+ .pba = 20,
+ .max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN,
+ .get_variants = e1000_get_variants_82571,
+ .mac_ops = &e82571_mac_ops,
+ .phy_ops = &e82_phy_ops_bm,
+ .nvm_ops = &e82571_nvm_ops,
};
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff