/* bnx2x_reg.h: Broadcom Everest network driver.
*
- * Copyright (c) 2007 Broadcom Corporation
+ * Copyright (c) 2007-2009 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation.
*
- * The registers description starts with the regsister Access type followed
+ * The registers description starts with the register Access type followed
* by size in bits. For example [RW 32]. The access types are:
* R - Read only
* RC - Clear on read
#define BRB1_REG_BRB1_INT_STS 0x6011c
/* [RW 4] Parity mask register #0 read/write */
#define BRB1_REG_BRB1_PRTY_MASK 0x60138
+/* [R 4] Parity register #0 read */
+#define BRB1_REG_BRB1_PRTY_STS 0x6012c
/* [RW 10] At address BRB1_IND_FREE_LIST_PRS_CRDT initialize free head. At
address BRB1_IND_FREE_LIST_PRS_CRDT+1 initialize free tail. At address
BRB1_IND_FREE_LIST_PRS_CRDT+2 initialize parser initial credit. */
#define BRB1_REG_FREE_LIST_PRS_CRDT 0x60200
+/* [RW 10] The number of free blocks above which the High_llfc signal to
+ interface #n is de-asserted. */
+#define BRB1_REG_HIGH_LLFC_HIGH_THRESHOLD_0 0x6014c
+/* [RW 10] The number of free blocks below which the High_llfc signal to
+ interface #n is asserted. */
+#define BRB1_REG_HIGH_LLFC_LOW_THRESHOLD_0 0x6013c
/* [RW 23] LL RAM data. */
#define BRB1_REG_LL_RAM 0x61000
+/* [RW 10] The number of free blocks above which the Low_llfc signal to
+ interface #n is de-asserted. */
+#define BRB1_REG_LOW_LLFC_HIGH_THRESHOLD_0 0x6016c
+/* [RW 10] The number of free blocks below which the Low_llfc signal to
+ interface #n is asserted. */
+#define BRB1_REG_LOW_LLFC_LOW_THRESHOLD_0 0x6015c
/* [R 24] The number of full blocks. */
#define BRB1_REG_NUM_OF_FULL_BLOCKS 0x60090
/* [ST 32] The number of cycles that the write_full signal towards MAC #0
was asserted. */
#define BRB1_REG_NUM_OF_FULL_CYCLES_0 0x600c8
#define BRB1_REG_NUM_OF_FULL_CYCLES_1 0x600cc
-#define BRB1_REG_NUM_OF_FULL_CYCLES_2 0x600d0
-#define BRB1_REG_NUM_OF_FULL_CYCLES_3 0x600d4
#define BRB1_REG_NUM_OF_FULL_CYCLES_4 0x600d8
/* [ST 32] The number of cycles that the pause signal towards MAC #0 was
asserted. */
#define BRB1_REG_NUM_OF_PAUSE_CYCLES_0 0x600b8
#define BRB1_REG_NUM_OF_PAUSE_CYCLES_1 0x600bc
-#define BRB1_REG_NUM_OF_PAUSE_CYCLES_2 0x600c0
-#define BRB1_REG_NUM_OF_PAUSE_CYCLES_3 0x600c4
/* [RW 10] Write client 0: De-assert pause threshold. */
#define BRB1_REG_PAUSE_HIGH_THRESHOLD_0 0x60078
#define BRB1_REG_PAUSE_HIGH_THRESHOLD_1 0x6007c
/* [RW 10] Write client 0: Assert pause threshold. */
#define BRB1_REG_PAUSE_LOW_THRESHOLD_0 0x60068
#define BRB1_REG_PAUSE_LOW_THRESHOLD_1 0x6006c
+/* [R 24] The number of full blocks occupied by port. */
+#define BRB1_REG_PORT_NUM_OCC_BLOCKS_0 0x60094
/* [RW 1] Reset the design by software. */
#define BRB1_REG_SOFT_RESET 0x600dc
/* [R 5] Used to read the value of the XX protection CAM occupancy counter. */
#define CCM_REG_CCM_INT_MASK 0xd01e4
/* [R 11] Interrupt register #0 read */
#define CCM_REG_CCM_INT_STS 0xd01d8
+/* [R 27] Parity register #0 read */
+#define CCM_REG_CCM_PRTY_STS 0xd01e8
/* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
stands for weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define CCM_REG_CQM_P_WEIGHT 0xd00b8
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_CQM_S_WEIGHT 0xd00bc
/* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the SDM interface is detected. */
#define CCM_REG_CSDM_LENGTH_MIS 0xd0170
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_CSDM_WEIGHT 0xd00b4
/* [RW 28] The CM header for QM formatting in case of an error in the QM
inputs. */
#define CCM_REG_ERR_CCM_HDR 0xd0094
_(0..15) stands for the connection type (one of 16). */
#define CCM_REG_N_SM_CTX_LD_0 0xd004c
#define CCM_REG_N_SM_CTX_LD_1 0xd0050
-#define CCM_REG_N_SM_CTX_LD_10 0xd0074
-#define CCM_REG_N_SM_CTX_LD_11 0xd0078
-#define CCM_REG_N_SM_CTX_LD_12 0xd007c
-#define CCM_REG_N_SM_CTX_LD_13 0xd0080
-#define CCM_REG_N_SM_CTX_LD_14 0xd0084
-#define CCM_REG_N_SM_CTX_LD_15 0xd0088
#define CCM_REG_N_SM_CTX_LD_2 0xd0054
#define CCM_REG_N_SM_CTX_LD_3 0xd0058
#define CCM_REG_N_SM_CTX_LD_4 0xd005c
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define CCM_REG_PBF_WEIGHT 0xd00ac
-/* [RW 6] The physical queue number of queue number 1 per port index. */
#define CCM_REG_PHYS_QNUM1_0 0xd0134
#define CCM_REG_PHYS_QNUM1_1 0xd0138
-/* [RW 6] The physical queue number of queue number 2 per port index. */
#define CCM_REG_PHYS_QNUM2_0 0xd013c
#define CCM_REG_PHYS_QNUM2_1 0xd0140
-/* [RW 6] The physical queue number of queue number 3 per port index. */
#define CCM_REG_PHYS_QNUM3_0 0xd0144
-/* [RW 6] The physical queue number of queue number 0 with QOS equal 0 port
- index 0. */
+#define CCM_REG_PHYS_QNUM3_1 0xd0148
#define CCM_REG_QOS_PHYS_QNUM0_0 0xd0114
#define CCM_REG_QOS_PHYS_QNUM0_1 0xd0118
-/* [RW 6] The physical queue number of queue number 0 with QOS equal 1 port
- index 0. */
#define CCM_REG_QOS_PHYS_QNUM1_0 0xd011c
#define CCM_REG_QOS_PHYS_QNUM1_1 0xd0120
-/* [RW 6] The physical queue number of queue number 0 with QOS equal 2 port
- index 0. */
#define CCM_REG_QOS_PHYS_QNUM2_0 0xd0124
+#define CCM_REG_QOS_PHYS_QNUM2_1 0xd0128
+#define CCM_REG_QOS_PHYS_QNUM3_0 0xd012c
+#define CCM_REG_QOS_PHYS_QNUM3_1 0xd0130
/* [RW 1] STORM - CM Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the STORM interface is detected. */
#define CCM_REG_STORM_LENGTH_MIS 0xd016c
+/* [RW 3] The weight of the STORM input in the WRR (Weighted Round robin)
+ mechanism. 0 stands for weight 8 (the most prioritised); 1 stands for
+ weight 1(least prioritised); 2 stands for weight 2 (more prioritised);
+ tc. */
+#define CCM_REG_STORM_WEIGHT 0xd009c
/* [RW 1] Input tsem Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
mechanism. The fields are: [5:0] - message length; [12:6] - message
pointer; 18:13] - next pointer. */
#define CCM_REG_XX_DESCR_TABLE 0xd0300
+#define CCM_REG_XX_DESCR_TABLE_SIZE 36
/* [R 7] Used to read the value of XX protection Free counter. */
#define CCM_REG_XX_FREE 0xd0184
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
#define CDU_REG_CDU_INT_STS 0x101030
/* [RW 5] Parity mask register #0 read/write */
#define CDU_REG_CDU_PRTY_MASK 0x10104c
+/* [R 5] Parity register #0 read */
+#define CDU_REG_CDU_PRTY_STS 0x101040
/* [RC 32] logging of error data in case of a CDU load error:
{expected_cid[15:0]; xpected_type[2:0]; xpected_region[2:0]; ctive_error;
ype_error; ctual_active; ctual_compressed_context}; */
/* [WB 24] MATT ram access. each entry has the following
format:{RegionLength[11:0]; egionOffset[11:0]} */
#define CDU_REG_MATT 0x101100
+/* [RW 1] when this bit is set the CDU operates in e1hmf mode */
+#define CDU_REG_MF_MODE 0x101050
/* [R 1] indication the initializing the activity counter by the hardware
was done. */
#define CFC_REG_AC_INIT_DONE 0x104078
#define CFC_REG_CFC_INT_STS_CLR 0x104100
/* [RW 4] Parity mask register #0 read/write */
#define CFC_REG_CFC_PRTY_MASK 0x104118
+/* [R 4] Parity register #0 read */
+#define CFC_REG_CFC_PRTY_STS 0x10410c
/* [RW 21] CID cam access (21:1 - Data; alid - 0) */
#define CFC_REG_CID_CAM 0x104800
#define CFC_REG_CONTROL0 0x104028
set one of these bits. the bit description can be found in CFC
specifications */
#define CFC_REG_ERROR_VECTOR 0x10403c
+/* [WB 93] LCID info ram access */
+#define CFC_REG_INFO_RAM 0x105000
+#define CFC_REG_INFO_RAM_SIZE 1024
#define CFC_REG_INIT_REG 0x10404c
+#define CFC_REG_INTERFACES 0x104058
/* [RW 24] {weight_load_client7[2:0] to weight_load_client0[2:0]}. this
field allows changing the priorities of the weighted-round-robin arbiter
which selects which CFC load client should be served next */
#define CFC_REG_LCREQ_WEIGHTS 0x104084
+/* [RW 16] Link List ram access; data = {prev_lcid; ext_lcid} */
+#define CFC_REG_LINK_LIST 0x104c00
+#define CFC_REG_LINK_LIST_SIZE 256
/* [R 1] indication the initializing the link list by the hardware was done. */
#define CFC_REG_LL_INIT_DONE 0x104074
/* [R 9] Number of allocated LCIDs which are at empty state */
#define CFC_REG_NUM_LCIDS_ALLOC 0x104020
/* [R 9] Number of Arriving LCIDs in Link List Block */
#define CFC_REG_NUM_LCIDS_ARRIVING 0x104004
-/* [R 9] Number of Inside LCIDs in Link List Block */
-#define CFC_REG_NUM_LCIDS_INSIDE 0x104008
/* [R 9] Number of Leaving LCIDs in Link List Block */
#define CFC_REG_NUM_LCIDS_LEAVING 0x104018
/* [RW 8] The event id for aggregated interrupt 0 */
#define CSDM_REG_AGG_INT_EVENT_0 0xc2038
+#define CSDM_REG_AGG_INT_EVENT_10 0xc2060
+#define CSDM_REG_AGG_INT_EVENT_11 0xc2064
+#define CSDM_REG_AGG_INT_EVENT_12 0xc2068
+#define CSDM_REG_AGG_INT_EVENT_13 0xc206c
+#define CSDM_REG_AGG_INT_EVENT_14 0xc2070
+#define CSDM_REG_AGG_INT_EVENT_15 0xc2074
+#define CSDM_REG_AGG_INT_EVENT_16 0xc2078
+#define CSDM_REG_AGG_INT_EVENT_2 0xc2040
+#define CSDM_REG_AGG_INT_EVENT_3 0xc2044
+#define CSDM_REG_AGG_INT_EVENT_4 0xc2048
+#define CSDM_REG_AGG_INT_EVENT_5 0xc204c
+#define CSDM_REG_AGG_INT_EVENT_6 0xc2050
+#define CSDM_REG_AGG_INT_EVENT_7 0xc2054
+#define CSDM_REG_AGG_INT_EVENT_8 0xc2058
+#define CSDM_REG_AGG_INT_EVENT_9 0xc205c
+/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
+ or auto-mask-mode (1) */
+#define CSDM_REG_AGG_INT_MODE_10 0xc21e0
+#define CSDM_REG_AGG_INT_MODE_11 0xc21e4
+#define CSDM_REG_AGG_INT_MODE_12 0xc21e8
+#define CSDM_REG_AGG_INT_MODE_13 0xc21ec
+#define CSDM_REG_AGG_INT_MODE_14 0xc21f0
+#define CSDM_REG_AGG_INT_MODE_15 0xc21f4
+#define CSDM_REG_AGG_INT_MODE_16 0xc21f8
+#define CSDM_REG_AGG_INT_MODE_6 0xc21d0
+#define CSDM_REG_AGG_INT_MODE_7 0xc21d4
+#define CSDM_REG_AGG_INT_MODE_8 0xc21d8
+#define CSDM_REG_AGG_INT_MODE_9 0xc21dc
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define CSDM_REG_CFC_RSP_START_ADDR 0xc2008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RW 32] Interrupt mask register #0 read/write */
#define CSDM_REG_CSDM_INT_MASK_0 0xc229c
#define CSDM_REG_CSDM_INT_MASK_1 0xc22ac
+/* [R 32] Interrupt register #0 read */
+#define CSDM_REG_CSDM_INT_STS_0 0xc2290
+#define CSDM_REG_CSDM_INT_STS_1 0xc22a0
/* [RW 11] Parity mask register #0 read/write */
#define CSDM_REG_CSDM_PRTY_MASK 0xc22bc
+/* [R 11] Parity register #0 read */
+#define CSDM_REG_CSDM_PRTY_STS 0xc22b0
#define CSDM_REG_ENABLE_IN1 0xc2238
#define CSDM_REG_ENABLE_IN2 0xc223c
#define CSDM_REG_ENABLE_OUT1 0xc2240
/* [RW 32] Interrupt mask register #0 read/write */
#define CSEM_REG_CSEM_INT_MASK_0 0x200110
#define CSEM_REG_CSEM_INT_MASK_1 0x200120
+/* [R 32] Interrupt register #0 read */
+#define CSEM_REG_CSEM_INT_STS_0 0x200104
+#define CSEM_REG_CSEM_INT_STS_1 0x200114
/* [RW 32] Parity mask register #0 read/write */
#define CSEM_REG_CSEM_PRTY_MASK_0 0x200130
#define CSEM_REG_CSEM_PRTY_MASK_1 0x200140
+/* [R 32] Parity register #0 read */
+#define CSEM_REG_CSEM_PRTY_STS_0 0x200124
+#define CSEM_REG_CSEM_PRTY_STS_1 0x200134
#define CSEM_REG_ENABLE_IN 0x2000a4
#define CSEM_REG_ENABLE_OUT 0x2000a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers the base address
- CSEM_REGISTERS_FAST_MEMORY (Offset: 0x220000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define CSEM_REG_FAST_MEMORY 0x220000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
#define CSEM_REG_TS_9_AS 0x20005c
/* [RW 1] Parity mask register #0 read/write */
#define DBG_REG_DBG_PRTY_MASK 0xc0a8
-/* [RW 2] debug only: These bits indicate the credit for PCI request type 4
- interface; MUST be configured AFTER pci_ext_buffer_strt_addr_lsb/msb are
- configured */
-#define DBG_REG_PCI_REQ_CREDIT 0xc120
+/* [R 1] Parity register #0 read */
+#define DBG_REG_DBG_PRTY_STS 0xc09c
/* [RW 32] Commands memory. The address to command X; row Y is to calculated
as 14*X+Y. */
#define DMAE_REG_CMD_MEM 0x102400
+#define DMAE_REG_CMD_MEM_SIZE 224
/* [RW 1] If 0 - the CRC-16c initial value is all zeroes; if 1 - the CRC-16c
initial value is all ones. */
#define DMAE_REG_CRC16C_INIT 0x10201c
#define DMAE_REG_DMAE_INT_MASK 0x102054
/* [RW 4] Parity mask register #0 read/write */
#define DMAE_REG_DMAE_PRTY_MASK 0x102064
+/* [R 4] Parity register #0 read */
+#define DMAE_REG_DMAE_PRTY_STS 0x102058
/* [RW 1] Command 0 go. */
#define DMAE_REG_GO_C0 0x102080
/* [RW 1] Command 1 go. */
#define DMAE_REG_GO_C1 0x102084
/* [RW 1] Command 10 go. */
#define DMAE_REG_GO_C10 0x102088
-#define DMAE_REG_GO_C10_SIZE 1
-/* [RW 1] Command 11 go. */
-#define DMAE_REG_GO_C11 0x10208c
-#define DMAE_REG_GO_C11_SIZE 1
-/* [RW 1] Command 12 go. */
-#define DMAE_REG_GO_C12 0x102090
-#define DMAE_REG_GO_C12_SIZE 1
-/* [RW 1] Command 13 go. */
-#define DMAE_REG_GO_C13 0x102094
-#define DMAE_REG_GO_C13_SIZE 1
-/* [RW 1] Command 14 go. */
-#define DMAE_REG_GO_C14 0x102098
-#define DMAE_REG_GO_C14_SIZE 1
-/* [RW 1] Command 15 go. */
-#define DMAE_REG_GO_C15 0x10209c
-#define DMAE_REG_GO_C15_SIZE 1
-/* [RW 1] Command 10 go. */
-#define DMAE_REG_GO_C10 0x102088
/* [RW 1] Command 11 go. */
#define DMAE_REG_GO_C11 0x10208c
/* [RW 1] Command 12 go. */
#define DORQ_REG_AGG_CMD3 0x17006c
/* [RW 28] UCM Header. */
#define DORQ_REG_CMHEAD_RX 0x170050
+/* [RW 32] Doorbell address for RBC doorbells (function 0). */
+#define DORQ_REG_DB_ADDR0 0x17008c
/* [RW 5] Interrupt mask register #0 read/write */
#define DORQ_REG_DORQ_INT_MASK 0x170180
/* [R 5] Interrupt register #0 read */
#define DORQ_REG_DORQ_INT_STS_CLR 0x170178
/* [RW 2] Parity mask register #0 read/write */
#define DORQ_REG_DORQ_PRTY_MASK 0x170190
+/* [R 2] Parity register #0 read */
+#define DORQ_REG_DORQ_PRTY_STS 0x170184
/* [RW 8] The address to write the DPM CID to STORM. */
#define DORQ_REG_DPM_CID_ADDR 0x170044
/* [RW 5] The DPM mode CID extraction offset. */
#define DORQ_REG_SHRT_CMHEAD 0x170054
#define HC_CONFIG_0_REG_ATTN_BIT_EN_0 (0x1<<4)
#define HC_CONFIG_0_REG_INT_LINE_EN_0 (0x1<<3)
+#define HC_CONFIG_0_REG_MSI_ATTN_EN_0 (0x1<<7)
#define HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 (0x1<<2)
#define HC_CONFIG_0_REG_SINGLE_ISR_EN_0 (0x1<<1)
#define HC_REG_AGG_INT_0 0x108050
#define HC_REG_AGG_INT_1 0x108054
-/* [RW 16] attention bit and attention acknowledge bits status for port 0
- and 1 according to the following address map: addr 0 - attn_bit_0; addr 1
- - attn_ack_bit_0; addr 2 - attn_bit_1; addr 3 - attn_ack_bit_1; */
#define HC_REG_ATTN_BIT 0x108120
-/* [RW 16] attn bits status index for attn bit msg; addr 0 - function 0;
- addr 1 - functin 1 */
#define HC_REG_ATTN_IDX 0x108100
-/* [RW 32] port 0 lower 32 bits address field for attn messag. */
#define HC_REG_ATTN_MSG0_ADDR_L 0x108018
-/* [RW 32] port 1 lower 32 bits address field for attn messag. */
#define HC_REG_ATTN_MSG1_ADDR_L 0x108020
-/* [RW 8] status block number for attn bit msg - function 0; */
#define HC_REG_ATTN_NUM_P0 0x108038
-/* [RW 8] status block number for attn bit msg - function 1 */
#define HC_REG_ATTN_NUM_P1 0x10803c
+#define HC_REG_COMMAND_REG 0x108180
#define HC_REG_CONFIG_0 0x108000
#define HC_REG_CONFIG_1 0x108004
+#define HC_REG_FUNC_NUM_P0 0x1080ac
+#define HC_REG_FUNC_NUM_P1 0x1080b0
/* [RW 3] Parity mask register #0 read/write */
#define HC_REG_HC_PRTY_MASK 0x1080a0
-/* [RW 17] status block interrupt mask; one in each bit means unmask; zerow
- in each bit means mask; bit 0 - default SB; bit 1 - SB_0; bit 2 - SB_1...
- bit 16- SB_15; addr 0 - port 0; addr 1 - port 1 */
+/* [R 3] Parity register #0 read */
+#define HC_REG_HC_PRTY_STS 0x108094
#define HC_REG_INT_MASK 0x108108
-/* [RW 16] port 0 attn bit condition monitoring; each bit that is set will
- lock a change fron 0 to 1 in the corresponding attention signals that
- comes from the AEU */
#define HC_REG_LEADING_EDGE_0 0x108040
#define HC_REG_LEADING_EDGE_1 0x108048
-/* [RW 16] all producer and consumer of port 0 according to the following
- addresses; U_prod: 0-15; C_prod: 16-31; U_cons: 32-47; C_cons:48-63;
- Defoult_prod: U/C/X/T/Attn-64/65/66/67/68; Defoult_cons:
- U/C/X/T/Attn-69/70/71/72/73 */
#define HC_REG_P0_PROD_CONS 0x108200
-/* [RW 16] all producer and consumer of port 1according to the following
- addresses; U_prod: 0-15; C_prod: 16-31; U_cons: 32-47; C_cons:48-63;
- Defoult_prod: U/C/X/T/Attn-64/65/66/67/68; Defoult_cons:
- U/C/X/T/Attn-69/70/71/72/73 */
#define HC_REG_P1_PROD_CONS 0x108400
-/* [W 1] This register is write only and has 4 addresses as follow: 0 =
- clear all PBA bits port 0; 1 = clear all pending interrupts request
- port0; 2 = clear all PBA bits port 1; 3 = clear all pending interrupts
- request port1; here is no meaning for the data in this register */
#define HC_REG_PBA_COMMAND 0x108140
#define HC_REG_PCI_CONFIG_0 0x108010
#define HC_REG_PCI_CONFIG_1 0x108014
-/* [RW 24] all counters acording to the following address: LSB: 0=read; 1=
- read_clear; 0-71 = HW counters (the inside order is the same as the
- interrupt table in the spec); 72-219 = SW counters 1 (stops after first
- consumer upd) the inside order is: 72-103 - U_non_default_p0; 104-135
- C_non_defaul_p0; 36-145 U/C/X/T/Attn_default_p0; 146-177
- U_non_default_p1; 178-209 C_non_defaul_p1; 10-219 U/C/X/T/Attn_default_p1
- ; 220-367 = SW counters 2 (stops when prod=cons) the inside order is:
- 220-251 - U_non_default_p0; 252-283 C_non_defaul_p0; 84-293
- U/C/X/T/Attn_default_p0; 294-325 U_non_default_p1; 326-357
- C_non_defaul_p1; 58-367 U/C/X/T/Attn_default_p1 ; 368-515 = mailbox
- counters; (the inside order of the mailbox counter is 368-431 U and C
- non_default_p0; 432-441 U/C/X/T/Attn_default_p0; 442-505 U and C
- non_default_p1; 506-515 U/C/X/T/Attn_default_p1) */
#define HC_REG_STATISTIC_COUNTERS 0x109000
-/* [RW 16] port 0 attn bit condition monitoring; each bit that is set will
- lock a change fron 1 to 0 in the corresponding attention signals that
- comes from the AEU */
#define HC_REG_TRAILING_EDGE_0 0x108044
#define HC_REG_TRAILING_EDGE_1 0x10804c
#define HC_REG_UC_RAM_ADDR_0 0x108028
#define HC_REG_UC_RAM_ADDR_1 0x108030
-/* [RW 16] ustorm address for coalesc now message */
#define HC_REG_USTORM_ADDR_FOR_COALESCE 0x108068
#define HC_REG_VQID_0 0x108008
#define HC_REG_VQID_1 0x10800c
#define MCP_REG_MCPR_NVM_READ 0x86410
#define MCP_REG_MCPR_NVM_SW_ARB 0x86420
#define MCP_REG_MCPR_NVM_WRITE 0x86408
-#define MCP_REG_MCPR_NVM_WRITE1 0x86428
#define MCP_REG_MCPR_SCRATCH 0xa0000
/* [R 32] read first 32 bit after inversion of function 0. mapped as
follows: [0] NIG attention for function0; [1] NIG attention for
rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP Latched
ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_AFTER_INVERT_4_MCP 0xa458
-/* [W 11] write to this register results with the clear of the latched
+/* [W 14] write to this register results with the clear of the latched
signals; one in d0 clears RBCR latch; one in d1 clears RBCT latch; one in
d2 clears RBCN latch; one in d3 clears RBCU latch; one in d4 clears RBCP
latch; one in d5 clears GRC Latched timeout attention; one in d6 clears
GRC Latched reserved access attention; one in d7 clears Latched
rom_parity; one in d8 clears Latched ump_rx_parity; one in d9 clears
- Latched ump_tx_parity; one in d10 clears Latched scpad_parity; read from
- this register return zero */
+ Latched ump_tx_parity; one in d10 clears Latched scpad_parity (both
+ ports); one in d11 clears pxpv_misc_mps_attn; one in d12 clears
+ pxp_misc_exp_rom_attn0; one in d13 clears pxp_misc_exp_rom_attn1; read
+ from this register return zero */
#define MISC_REG_AEU_CLR_LATCH_SIGNAL 0xa45c
/* [RW 32] first 32b for enabling the output for function 0 output0. mapped
as follows: [0] NIG attention for function0; [1] NIG attention for
TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0 0xa06c
#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_1 0xa07c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_2 0xa08c
#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_3 0xa09c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_5 0xa0bc
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_6 0xa0cc
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_7 0xa0dc
/* [RW 32] first 32b for enabling the output for function 1 output0. mapped
as follows: [0] NIG attention for function0; [1] NIG attention for
function1; [2] GPIO1 function 1; [3] GPIO2 function 1; [4] GPIO3 function
TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 0xa10c
#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_1 0xa11c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_2 0xa12c
#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_3 0xa13c
-/* [RW 32] first 32b for enabling the output for close the gate nig 0.
- mapped as follows: [0] NIG attention for function0; [1] NIG attention for
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_5 0xa15c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_6 0xa16c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_7 0xa17c
+/* [RW 32] first 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function
0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
#define MISC_REG_AEU_ENABLE1_NIG_0 0xa0ec
#define MISC_REG_AEU_ENABLE1_NIG_1 0xa18c
-/* [RW 32] first 32b for enabling the output for close the gate pxp 0.
- mapped as follows: [0] NIG attention for function0; [1] NIG attention for
+/* [RW 32] first 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function
0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
interrupt; */
#define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_0 0xa110
#define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_1 0xa120
-/* [RW 32] second 32b for enabling the output for close the gate nig 0.
- mapped as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt;
- [2] QM Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5]
- Timers Hw interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8]
- XCM Parity error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11]
- XSEMI Hw interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw
- interrupt; [14] NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI
- core Parity error; [17] Vaux PCI core Hw interrupt; [18] Debug Parity
- error; [19] Debug Hw interrupt; [20] USDM Parity error; [21] USDM Hw
- interrupt; [22] UCM Parity error; [23] UCM Hw interrupt; [24] USEMI
- Parity error; [25] USEMI Hw interrupt; [26] UPB Parity error; [27] UPB Hw
- interrupt; [28] CSDM Parity error; [29] CSDM Hw interrupt; [30] CCM
- Parity error; [31] CCM Hw interrupt; */
+/* [RW 32] second 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
#define MISC_REG_AEU_ENABLE2_NIG_0 0xa0f0
#define MISC_REG_AEU_ENABLE2_NIG_1 0xa190
-/* [RW 32] second 32b for enabling the output for close the gate pxp 0.
- mapped as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt;
- [2] QM Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5]
- Timers Hw interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8]
- XCM Parity error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11]
- XSEMI Hw interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw
- interrupt; [14] NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI
- core Parity error; [17] Vaux PCI core Hw interrupt; [18] Debug Parity
- error; [19] Debug Hw interrupt; [20] USDM Parity error; [21] USDM Hw
- interrupt; [22] UCM Parity error; [23] UCM Hw interrupt; [24] USEMI
- Parity error; [25] USEMI Hw interrupt; [26] UPB Parity error; [27] UPB Hw
- interrupt; [28] CSDM Parity error; [29] CSDM Hw interrupt; [30] CCM
- Parity error; [31] CCM Hw interrupt; */
+/* [RW 32] second 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
#define MISC_REG_AEU_ENABLE2_PXP_0 0xa100
#define MISC_REG_AEU_ENABLE2_PXP_1 0xa1a0
/* [RW 32] third 32b for enabling the output for function 0 output0. mapped
attn1; */
#define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_0 0xa114
#define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_1 0xa124
-/* [RW 32] third 32b for enabling the output for close the gate nig 0.
- mapped as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2]
- PXP Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity
- error; [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC
- Hw interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE
- Parity error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13]
- IGU (HC) Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt;
- [16] pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0;
- [20] MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0;
- [23] SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST;
- [26] SW timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers
- attn_3 func1; [29] SW timers attn_4 func1; [30] General attn0; [31]
- General attn1; */
+/* [RW 32] third 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
#define MISC_REG_AEU_ENABLE3_NIG_0 0xa0f4
#define MISC_REG_AEU_ENABLE3_NIG_1 0xa194
-/* [RW 32] third 32b for enabling the output for close the gate pxp 0.
- mapped as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2]
- PXP Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity
- error; [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC
- Hw interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE
- Parity error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13]
- IGU (HC) Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt;
- [16] pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0;
- [20] MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0;
- [23] SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST;
- [26] SW timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers
- attn_3 func1; [29] SW timers attn_4 func1; [30] General attn0; [31]
- General attn1; */
+/* [RW 32] third 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
#define MISC_REG_AEU_ENABLE3_PXP_0 0xa104
#define MISC_REG_AEU_ENABLE3_PXP_1 0xa1a4
/* [RW 32] fourth 32b for enabling the output for function 0 output0.mapped
Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_0 0xa078
#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_2 0xa098
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_4 0xa0b8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_5 0xa0c8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_6 0xa0d8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_7 0xa0e8
/* [RW 32] fourth 32b for enabling the output for function 1 output0.mapped
as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_0 0xa118
#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_2 0xa138
-/* [RW 32] fourth 32b for enabling the output for close the gate nig
- 0.mapped as follows: [0] General attn2; [1] General attn3; [2] General
- attn4; [3] General attn5; [4] General attn6; [5] General attn7; [6]
- General attn8; [7] General attn9; [8] General attn10; [9] General attn11;
- [10] General attn12; [11] General attn13; [12] General attn14; [13]
- General attn15; [14] General attn16; [15] General attn17; [16] General
- attn18; [17] General attn19; [18] General attn20; [19] General attn21;
- [20] Main power interrupt; [21] RBCR Latched attn; [22] RBCT Latched
- attn; [23] RBCN Latched attn; [24] RBCU Latched attn; [25] RBCP Latched
- attn; [26] GRC Latched timeout attention; [27] GRC Latched reserved
- access attention; [28] MCP Latched rom_parity; [29] MCP Latched
- ump_rx_parity; [30] MCP Latched ump_tx_parity; [31] MCP Latched
- scpad_parity; */
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_4 0xa158
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_5 0xa168
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_6 0xa178
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_7 0xa188
+/* [RW 32] fourth 32b for enabling the output for close the gate nig.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_NIG_0 0xa0f8
#define MISC_REG_AEU_ENABLE4_NIG_1 0xa198
-/* [RW 32] fourth 32b for enabling the output for close the gate pxp
- 0.mapped as follows: [0] General attn2; [1] General attn3; [2] General
- attn4; [3] General attn5; [4] General attn6; [5] General attn7; [6]
- General attn8; [7] General attn9; [8] General attn10; [9] General attn11;
- [10] General attn12; [11] General attn13; [12] General attn14; [13]
- General attn15; [14] General attn16; [15] General attn17; [16] General
- attn18; [17] General attn19; [18] General attn20; [19] General attn21;
- [20] Main power interrupt; [21] RBCR Latched attn; [22] RBCT Latched
- attn; [23] RBCN Latched attn; [24] RBCU Latched attn; [25] RBCP Latched
- attn; [26] GRC Latched timeout attention; [27] GRC Latched reserved
- access attention; [28] MCP Latched rom_parity; [29] MCP Latched
- ump_rx_parity; [30] MCP Latched ump_tx_parity; [31] MCP Latched
- scpad_parity; */
+/* [RW 32] fourth 32b for enabling the output for close the gate pxp.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_PXP_0 0xa108
#define MISC_REG_AEU_ENABLE4_PXP_1 0xa1a8
/* [RW 1] set/clr general attention 0; this will set/clr bit 94 in the aeu
#define MISC_REG_AEU_GENERAL_ATTN_10 0xa028
#define MISC_REG_AEU_GENERAL_ATTN_11 0xa02c
#define MISC_REG_AEU_GENERAL_ATTN_12 0xa030
-#define MISC_REG_AEU_GENERAL_ATTN_13 0xa034
-#define MISC_REG_AEU_GENERAL_ATTN_14 0xa038
-#define MISC_REG_AEU_GENERAL_ATTN_15 0xa03c
-#define MISC_REG_AEU_GENERAL_ATTN_16 0xa040
-#define MISC_REG_AEU_GENERAL_ATTN_17 0xa044
-#define MISC_REG_AEU_GENERAL_ATTN_18 0xa048
-#define MISC_REG_AEU_GENERAL_ATTN_19 0xa04c
-#define MISC_REG_AEU_GENERAL_ATTN_11 0xa02c
#define MISC_REG_AEU_GENERAL_ATTN_2 0xa008
-#define MISC_REG_AEU_GENERAL_ATTN_20 0xa050
-#define MISC_REG_AEU_GENERAL_ATTN_21 0xa054
#define MISC_REG_AEU_GENERAL_ATTN_3 0xa00c
#define MISC_REG_AEU_GENERAL_ATTN_4 0xa010
#define MISC_REG_AEU_GENERAL_ATTN_5 0xa014
#define MISC_REG_AEU_GENERAL_ATTN_6 0xa018
+#define MISC_REG_AEU_GENERAL_ATTN_7 0xa01c
+#define MISC_REG_AEU_GENERAL_ATTN_8 0xa020
+#define MISC_REG_AEU_GENERAL_ATTN_9 0xa024
+#define MISC_REG_AEU_GENERAL_MASK 0xa61c
/* [RW 32] first 32b for inverting the input for function 0; for each bit:
0= do not invert; 1= invert; mapped as follows: [0] NIG attention for
function0; [1] NIG attention for function1; [2] GPIO1 mcp; [3] GPIO2 mcp;
#define MISC_REG_AEU_INVERTER_2_FUNC_0 0xa230
#define MISC_REG_AEU_INVERTER_2_FUNC_1 0xa240
/* [RW 10] [7:0] = mask 8 attention output signals toward IGU function0;
- [9:8] = mask close the gates signals of function 0 toward PXP [8] and NIG
- [9]. Zero = mask; one = unmask */
+ [9:8] = raserved. Zero = mask; one = unmask */
#define MISC_REG_AEU_MASK_ATTN_FUNC_0 0xa060
#define MISC_REG_AEU_MASK_ATTN_FUNC_1 0xa064
+/* [RW 1] If set a system kill occurred */
+#define MISC_REG_AEU_SYS_KILL_OCCURRED 0xa610
+/* [RW 32] Represent the status of the input vector to the AEU when a system
+ kill occurred. The register is reset in por reset. Mapped as follows: [0]
+ NIG attention for function0; [1] NIG attention for function1; [2] GPIO1
+ mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1;
+ [7] GPIO2 function 1; [8] GPIO3 function 1; [9] GPIO4 function 1; [10]
+ PCIE glue/PXP VPD event function0; [11] PCIE glue/PXP VPD event
+ function1; [12] PCIE glue/PXP Expansion ROM event0; [13] PCIE glue/PXP
+ Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16] MSI/X indication for
+ mcp; [17] MSI/X indication for function 1; [18] BRB Parity error; [19]
+ BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC
+ Parity error; [23] SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw
+ interrupt; [26] TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI
+ Parity error; [29] TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw
+ interrupt; */
+#define MISC_REG_AEU_SYS_KILL_STATUS_0 0xa600
+#define MISC_REG_AEU_SYS_KILL_STATUS_1 0xa604
+#define MISC_REG_AEU_SYS_KILL_STATUS_2 0xa608
+#define MISC_REG_AEU_SYS_KILL_STATUS_3 0xa60c
/* [R 4] This field indicates the type of the device. '0' - 2 Ports; '1' - 1
Port. */
#define MISC_REG_BOND_ID 0xa400
starts at 0x0 for the A0 tape-out and increments by one for each
all-layer tape-out. */
#define MISC_REG_CHIP_REV 0xa40c
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_1 0xa510
+#define MISC_REG_DRIVER_CONTROL_7 0xa3c8
+/* [RW 1] e1hmf for WOL. If clr WOL signal o the PXP will be send on bit 0
+ only. */
+#define MISC_REG_E1HMF_MODE 0xa5f8
+/* [RW 32] Debug only: spare RW register reset by core reset */
+#define MISC_REG_GENERIC_CR_0 0xa460
+/* [RW 32] GPIO. [31-28] FLOAT port 0; [27-24] FLOAT port 0; When any of
+ these bits is written as a '1'; the corresponding SPIO bit will turn off
+ it's drivers and become an input. This is the reset state of all GPIO
+ pins. The read value of these bits will be a '1' if that last command
+ (#SET; #CLR; or #FLOAT) for this bit was a #FLOAT. (reset value 0xff).
+ [23-20] CLR port 1; 19-16] CLR port 0; When any of these bits is written
+ as a '1'; the corresponding GPIO bit will drive low. The read value of
+ these bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for
+ this bit was a #CLR. (reset value 0). [15-12] SET port 1; 11-8] port 0;
+ SET When any of these bits is written as a '1'; the corresponding GPIO
+ bit will drive high (if it has that capability). The read value of these
+ bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for this
+ bit was a #SET. (reset value 0). [7-4] VALUE port 1; [3-0] VALUE port 0;
+ RO; These bits indicate the read value of each of the eight GPIO pins.
+ This is the result value of the pin; not the drive value. Writing these
+ bits will have not effect. */
+#define MISC_REG_GPIO 0xa490
+/* [RW 8] These bits enable the GPIO_INTs to signals event to the
+ IGU/MCP.according to the following map: [0] p0_gpio_0; [1] p0_gpio_1; [2]
+ p0_gpio_2; [3] p0_gpio_3; [4] p1_gpio_0; [5] p1_gpio_1; [6] p1_gpio_2;
+ [7] p1_gpio_3; */
+#define MISC_REG_GPIO_EVENT_EN 0xa2bc
+/* [RW 32] GPIO INT. [31-28] OLD_CLR port1; [27-24] OLD_CLR port0; Writing a
+ '1' to these bit clears the corresponding bit in the #OLD_VALUE register.
+ This will acknowledge an interrupt on the falling edge of corresponding
+ GPIO input (reset value 0). [23-16] OLD_SET [23-16] port1; OLD_SET port0;
+ Writing a '1' to these bit sets the corresponding bit in the #OLD_VALUE
+ register. This will acknowledge an interrupt on the rising edge of
+ corresponding SPIO input (reset value 0). [15-12] OLD_VALUE [11-8] port1;
+ OLD_VALUE port0; RO; These bits indicate the old value of the GPIO input
+ value. When the ~INT_STATE bit is set; this bit indicates the OLD value
+ of the pin such that if ~INT_STATE is set and this bit is '0'; then the
+ interrupt is due to a low to high edge. If ~INT_STATE is set and this bit
+ is '1'; then the interrupt is due to a high to low edge (reset value 0).
+ [7-4] INT_STATE port1; [3-0] INT_STATE RO port0; These bits indicate the
+ current GPIO interrupt state for each GPIO pin. This bit is cleared when
+ the appropriate #OLD_SET or #OLD_CLR command bit is written. This bit is
+ set when the GPIO input does not match the current value in #OLD_VALUE
+ (reset value 0). */
+#define MISC_REG_GPIO_INT 0xa494
+/* [R 28] this field hold the last information that caused reserved
+ attention. bits [19:0] - address; [22:20] function; [23] reserved;
+ [27:24] the master that caused the attention - according to the following
+ encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
+ dbu; 8 = dmae */
+#define MISC_REG_GRC_RSV_ATTN 0xa3c0
+/* [R 28] this field hold the last information that caused timeout
+ attention. bits [19:0] - address; [22:20] function; [23] reserved;
+ [27:24] the master that caused the attention - according to the following
+ encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
+ dbu; 8 = dmae */
+#define MISC_REG_GRC_TIMEOUT_ATTN 0xa3c4
/* [RW 1] Setting this bit enables a timer in the GRC block to timeout any
access that does not finish within
~misc_registers_grc_timout_val.grc_timeout_val cycles. When this bit is
#define MISC_REG_MISC_INT_MASK 0xa388
/* [RW 1] Parity mask register #0 read/write */
#define MISC_REG_MISC_PRTY_MASK 0xa398
+/* [R 1] Parity register #0 read */
+#define MISC_REG_MISC_PRTY_STS 0xa38c
+#define MISC_REG_NIG_WOL_P0 0xa270
+#define MISC_REG_NIG_WOL_P1 0xa274
+/* [R 1] If set indicate that the pcie_rst_b was asserted without perst
+ assertion */
+#define MISC_REG_PCIE_HOT_RESET 0xa618
/* [RW 32] 32 LSB of storm PLL first register; reset val = 0x 071d2911.
inside order of the bits is: [0] P1 divider[0] (reset value 1); [1] P1
divider[1] (reset value 0); [2] P1 divider[2] (reset value 0); [3] P1
#define MISC_REG_PLL_STORM_CTRL_2 0xa298
#define MISC_REG_PLL_STORM_CTRL_3 0xa29c
#define MISC_REG_PLL_STORM_CTRL_4 0xa2a0
-/* [RW 32] reset reg#1; rite/read one = the specific block is out of reset;
+/* [RW 32] reset reg#2; rite/read one = the specific block is out of reset;
write/read zero = the specific block is in reset; addr 0-wr- the write
value will be written to the register; addr 1-set - one will be written
to all the bits that have the value of one in the data written (bits that
written to all the bits that have the value of one in the data written
(bits that have the value of zero will not be change); addr 3-ignore;
read ignore from all addr except addr 00; inside order of the bits is:
- [0] rst_brb1; [1] rst_prs; [2] rst_src; [3] rst_tsdm; [4] rst_tsem; [5]
- rst_tcm; [6] rst_rbcr; [7] rst_nig; [8] rst_usdm; [9] rst_ucm; [10]
- rst_usem; [11] rst_upb; [12] rst_ccm; [13] rst_csem; [14] rst_csdm; [15]
- rst_rbcu; [16] rst_pbf; [17] rst_qm; [18] rst_tm; [19] rst_dorq; [20]
- rst_xcm; [21] rst_xsdm; [22] rst_xsem; [23] rst_rbct; [24] rst_cdu; [25]
- rst_cfc; [26] rst_pxp; [27] rst_pxpv; [28] rst_rbcp; [29] rst_hc; [30]
- rst_dmae; [31] rst_semi_rtc; */
-#define MISC_REG_RESET_REG_1 0xa580
+ [0] rst_bmac0; [1] rst_bmac1; [2] rst_emac0; [3] rst_emac1; [4] rst_grc;
+ [5] rst_mcp_n_reset_reg_hard_core; [6] rst_ mcp_n_hard_core_rst_b; [7]
+ rst_ mcp_n_reset_cmn_cpu; [8] rst_ mcp_n_reset_cmn_core; [9] rst_rbcn;
+ [10] rst_dbg; [11] rst_misc_core; [12] rst_dbue (UART); [13]
+ Pci_resetmdio_n; [14] rst_emac0_hard_core; [15] rst_emac1_hard_core; 16]
+ rst_pxp_rq_rd_wr; 31:17] reserved */
#define MISC_REG_RESET_REG_2 0xa590
/* [RW 20] 20 bit GRC address where the scratch-pad of the MCP that is
shared with the driver resides */
#define MISC_REG_SHARED_MEM_ADDR 0xa2b4
+/* [RW 32] SPIO. [31-24] FLOAT When any of these bits is written as a '1';
+ the corresponding SPIO bit will turn off it's drivers and become an
+ input. This is the reset state of all SPIO pins. The read value of these
+ bits will be a '1' if that last command (#SET; #CL; or #FLOAT) for this
+ bit was a #FLOAT. (reset value 0xff). [23-16] CLR When any of these bits
+ is written as a '1'; the corresponding SPIO bit will drive low. The read
+ value of these bits will be a '1' if that last command (#SET; #CLR; or
+#FLOAT) for this bit was a #CLR. (reset value 0). [15-8] SET When any of
+ these bits is written as a '1'; the corresponding SPIO bit will drive
+ high (if it has that capability). The read value of these bits will be a
+ '1' if that last command (#SET; #CLR; or #FLOAT) for this bit was a #SET.
+ (reset value 0). [7-0] VALUE RO; These bits indicate the read value of
+ each of the eight SPIO pins. This is the result value of the pin; not the
+ drive value. Writing these bits will have not effect. Each 8 bits field
+ is divided as follows: [0] VAUX Enable; when pulsed low; enables supply
+ from VAUX. (This is an output pin only; the FLOAT field is not applicable
+ for this pin); [1] VAUX Disable; when pulsed low; disables supply form
+ VAUX. (This is an output pin only; FLOAT field is not applicable for this
+ pin); [2] SEL_VAUX_B - Control to power switching logic. Drive low to
+ select VAUX supply. (This is an output pin only; it is not controlled by
+ the SET and CLR fields; it is controlled by the Main Power SM; the FLOAT
+ field is not applicable for this pin; only the VALUE fields is relevant -
+ it reflects the output value); [3] port swap [4] spio_4; [5] spio_5; [6]
+ Bit 0 of UMP device ID select; read by UMP firmware; [7] Bit 1 of UMP
+ device ID select; read by UMP firmware. */
+#define MISC_REG_SPIO 0xa4fc
+/* [RW 8] These bits enable the SPIO_INTs to signals event to the IGU/MC.
+ according to the following map: [3:0] reserved; [4] spio_4 [5] spio_5;
+ [7:0] reserved */
+#define MISC_REG_SPIO_EVENT_EN 0xa2b8
+/* [RW 32] SPIO INT. [31-24] OLD_CLR Writing a '1' to these bit clears the
+ corresponding bit in the #OLD_VALUE register. This will acknowledge an
+ interrupt on the falling edge of corresponding SPIO input (reset value
+ 0). [23-16] OLD_SET Writing a '1' to these bit sets the corresponding bit
+ in the #OLD_VALUE register. This will acknowledge an interrupt on the
+ rising edge of corresponding SPIO input (reset value 0). [15-8] OLD_VALUE
+ RO; These bits indicate the old value of the SPIO input value. When the
+ ~INT_STATE bit is set; this bit indicates the OLD value of the pin such
+ that if ~INT_STATE is set and this bit is '0'; then the interrupt is due
+ to a low to high edge. If ~INT_STATE is set and this bit is '1'; then the
+ interrupt is due to a high to low edge (reset value 0). [7-0] INT_STATE
+ RO; These bits indicate the current SPIO interrupt state for each SPIO
+ pin. This bit is cleared when the appropriate #OLD_SET or #OLD_CLR
+ command bit is written. This bit is set when the SPIO input does not
+ match the current value in #OLD_VALUE (reset value 0). */
+#define MISC_REG_SPIO_INT 0xa500
+/* [RW 32] reload value for counter 4 if reload; the value will be reload if
+ the counter reached zero and the reload bit
+ (~misc_registers_sw_timer_cfg_4.sw_timer_cfg_4[1] ) is set */
+#define MISC_REG_SW_TIMER_RELOAD_VAL_4 0xa2fc
+/* [RW 32] the value of the counter for sw timers1-8. there are 8 addresses
+ in this register. addres 0 - timer 1; address - timer 2�address 7 -
+ timer 8 */
+#define MISC_REG_SW_TIMER_VAL 0xa5c0
+/* [RW 1] Set by the MCP to remember if one or more of the drivers is/are
+ loaded; 0-prepare; -unprepare */
+#define MISC_REG_UNPREPARED 0xa424
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_BRCST (0x1<<0)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_MLCST (0x1<<1)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_NO_VLAN (0x1<<4)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_UNCST (0x1<<2)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_VLAN (0x1<<3)
#define NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT (0x1<<0)
#define NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS (0x1<<9)
#define NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G (0x1<<15)
#define NIG_REG_BRB1_PAUSE_IN_EN 0x100c8
/* [RW 1] output enable for RX BRB1 LP IF */
#define NIG_REG_BRB_LB_OUT_EN 0x10100
-/* [WB_W 72] Debug packet to LP from RBC; Data spelling:[63:0] data; 64]
- error; [67:65]eop_bvalid; [68]eop; [69]sop; [70]port_id; 71]flush */
+/* [WB_W 82] Debug packet to LP from RBC; Data spelling:[63:0] data; 64]
+ error; [67:65]eop_bvalid; [68]eop; [69]sop; [70]port_id; 71]flush;
+ 72:73]-vnic_num; 81:74]-sideband_info */
#define NIG_REG_DEBUG_PACKET_LB 0x10800
/* [RW 1] Input enable for TX Debug packet */
#define NIG_REG_EGRESS_DEBUG_IN_EN 0x100dc
#define NIG_REG_EGRESS_PBF0_IN_EN 0x100cc
/* [RW 1] Input enable for TX PBF user packet port1 IF */
#define NIG_REG_EGRESS_PBF1_IN_EN 0x100d0
+/* [RW 1] Input enable for TX UMP management packet port0 IF */
+#define NIG_REG_EGRESS_UMP0_IN_EN 0x100d4
/* [RW 1] Input enable for RX_EMAC0 IF */
#define NIG_REG_EMAC0_IN_EN 0x100a4
/* [RW 1] output enable for TX EMAC pause port 0 IF */
/* [RW 17] Debug only. RX_EOP_DSCR_lb_FIFO in NIG_RX_EOP. Data
packet_length[13:0]; mac_error[14]; trunc_error[15]; parity[16] */
#define NIG_REG_INGRESS_EOP_LB_FIFO 0x104e4
+/* [RW 27] 0 - must be active for Everest A0; 1- for Everest B0 when latch
+ logic for interrupts must be used. Enable per bit of interrupt of
+ ~latch_status.latch_status */
+#define NIG_REG_LATCH_BC_0 0x16210
+/* [RW 27] Latch for each interrupt from Unicore.b[0]
+ status_emac0_misc_mi_int; b[1] status_emac0_misc_mi_complete;
+ b[2]status_emac0_misc_cfg_change; b[3]status_emac0_misc_link_status;
+ b[4]status_emac0_misc_link_change; b[5]status_emac0_misc_attn;
+ b[6]status_serdes0_mac_crs; b[7]status_serdes0_autoneg_complete;
+ b[8]status_serdes0_fiber_rxact; b[9]status_serdes0_link_status;
+ b[10]status_serdes0_mr_page_rx; b[11]status_serdes0_cl73_an_complete;
+ b[12]status_serdes0_cl73_mr_page_rx; b[13]status_serdes0_rx_sigdet;
+ b[14]status_xgxs0_remotemdioreq; b[15]status_xgxs0_link10g;
+ b[16]status_xgxs0_autoneg_complete; b[17]status_xgxs0_fiber_rxact;
+ b[21:18]status_xgxs0_link_status; b[22]status_xgxs0_mr_page_rx;
+ b[23]status_xgxs0_cl73_an_complete; b[24]status_xgxs0_cl73_mr_page_rx;
+ b[25]status_xgxs0_rx_sigdet; b[26]status_xgxs0_mac_crs */
+#define NIG_REG_LATCH_STATUS_0 0x18000
/* [RW 1] led 10g for port 0 */
#define NIG_REG_LED_10G_P0 0x10320
+/* [RW 1] led 10g for port 1 */
+#define NIG_REG_LED_10G_P1 0x10324
/* [RW 1] Port0: This bit is set to enable the use of the
~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 field
defined below. If this bit is cleared; then the blink rate will be about
is reset to 0x080; giving a default blink period of approximately 8Hz. */
#define NIG_REG_LED_CONTROL_BLINK_RATE_P0 0x10310
/* [RW 1] Port0: If set along with the
- nig_registers_led_control_override_traffic_p0.led_control_override_traffic_p0
+ ~nig_registers_led_control_override_traffic_p0.led_control_override_traffic_p0
bit and ~nig_registers_led_control_traffic_p0.led_control_traffic_p0 LED
bit; the Traffic LED will blink with the blink rate specified in
~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 and
/* [RW 4] led mode for port0: 0 MAC; 1-3 PHY1; 4 MAC2; 5-7 PHY4; 8-MAC3;
9-11PHY7; 12 MAC4; 13-15 PHY10; */
#define NIG_REG_LED_MODE_P0 0x102f0
+/* [RW 3] for port0 enable for llfc ppp and pause. b0 - brb1 enable; b1-
+ tsdm enable; b2- usdm enable */
+#define NIG_REG_LLFC_EGRESS_SRC_ENABLE_0 0x16070
+#define NIG_REG_LLFC_EGRESS_SRC_ENABLE_1 0x16074
+/* [RW 1] SAFC enable for port0. This register may get 1 only when
+ ~ppp_enable.ppp_enable = 0 and pause_enable.pause_enable =0 for the same
+ port */
+#define NIG_REG_LLFC_ENABLE_0 0x16208
+/* [RW 16] classes are high-priority for port0 */
+#define NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_0 0x16058
+/* [RW 16] classes are low-priority for port0 */
+#define NIG_REG_LLFC_LOW_PRIORITY_CLASSES_0 0x16060
+/* [RW 1] Output enable of message to LLFC BMAC IF for port0 */
+#define NIG_REG_LLFC_OUT_EN_0 0x160c8
+#define NIG_REG_LLH0_ACPI_PAT_0_CRC 0x1015c
+#define NIG_REG_LLH0_ACPI_PAT_6_LEN 0x10154
#define NIG_REG_LLH0_BRB1_DRV_MASK 0x10244
+#define NIG_REG_LLH0_BRB1_DRV_MASK_MF 0x16048
/* [RW 1] send to BRB1 if no match on any of RMP rules. */
#define NIG_REG_LLH0_BRB1_NOT_MCP 0x1025c
+/* [RW 2] Determine the classification participants. 0: no classification.1:
+ classification upon VLAN id. 2: classification upon MAC address. 3:
+ classification upon both VLAN id & MAC addr. */
+#define NIG_REG_LLH0_CLS_TYPE 0x16080
/* [RW 32] cm header for llh0 */
#define NIG_REG_LLH0_CM_HEADER 0x1007c
+#define NIG_REG_LLH0_DEST_IP_0_1 0x101dc
+#define NIG_REG_LLH0_DEST_MAC_0_0 0x101c0
+/* [RW 16] destination TCP address 1. The LLH will look for this address in
+ all incoming packets. */
+#define NIG_REG_LLH0_DEST_TCP_0 0x10220
+/* [RW 16] destination UDP address 1 The LLH will look for this address in
+ all incoming packets. */
+#define NIG_REG_LLH0_DEST_UDP_0 0x10214
#define NIG_REG_LLH0_ERROR_MASK 0x1008c
/* [RW 8] event id for llh0 */
#define NIG_REG_LLH0_EVENT_ID 0x10084
+#define NIG_REG_LLH0_FUNC_EN 0x160fc
+#define NIG_REG_LLH0_FUNC_VLAN_ID 0x16100
+/* [RW 1] Determine the IP version to look for in
+ ~nig_registers_llh0_dest_ip_0.llh0_dest_ip_0. 0 - IPv6; 1-IPv4 */
+#define NIG_REG_LLH0_IPV4_IPV6_0 0x10208
+/* [RW 1] t bit for llh0 */
+#define NIG_REG_LLH0_T_BIT 0x10074
+/* [RW 12] VLAN ID 1. In case of VLAN packet the LLH will look for this ID. */
+#define NIG_REG_LLH0_VLAN_ID_0 0x1022c
/* [RW 8] init credit counter for port0 in LLH */
#define NIG_REG_LLH0_XCM_INIT_CREDIT 0x10554
#define NIG_REG_LLH0_XCM_MASK 0x10130
+#define NIG_REG_LLH1_BRB1_DRV_MASK 0x10248
/* [RW 1] send to BRB1 if no match on any of RMP rules. */
#define NIG_REG_LLH1_BRB1_NOT_MCP 0x102dc
+/* [RW 2] Determine the classification participants. 0: no classification.1:
+ classification upon VLAN id. 2: classification upon MAC address. 3:
+ classification upon both VLAN id & MAC addr. */
+#define NIG_REG_LLH1_CLS_TYPE 0x16084
/* [RW 32] cm header for llh1 */
#define NIG_REG_LLH1_CM_HEADER 0x10080
#define NIG_REG_LLH1_ERROR_MASK 0x10090
/* [RW 8] init credit counter for port1 in LLH */
#define NIG_REG_LLH1_XCM_INIT_CREDIT 0x10564
#define NIG_REG_LLH1_XCM_MASK 0x10134
+/* [RW 1] When this bit is set; the LLH will expect all packets to be with
+ e1hov */
+#define NIG_REG_LLH_E1HOV_MODE 0x160d8
+/* [RW 1] When this bit is set; the LLH will classify the packet before
+ sending it to the BRB or calculating WoL on it. */
+#define NIG_REG_LLH_MF_MODE 0x16024
#define NIG_REG_MASK_INTERRUPT_PORT0 0x10330
#define NIG_REG_MASK_INTERRUPT_PORT1 0x10334
/* [RW 1] Output signal from NIG to EMAC0. When set enables the EMAC0 block. */
#define NIG_REG_NIG_EMAC0_EN 0x1003c
+/* [RW 1] Output signal from NIG to EMAC1. When set enables the EMAC1 block. */
+#define NIG_REG_NIG_EMAC1_EN 0x10040
/* [RW 1] Output signal from NIG to TX_EMAC0. When set indicates to the
EMAC0 to strip the CRC from the ingress packets. */
#define NIG_REG_NIG_INGRESS_EMAC0_NO_CRC 0x10044
+/* [R 32] Interrupt register #0 read */
+#define NIG_REG_NIG_INT_STS_0 0x103b0
+#define NIG_REG_NIG_INT_STS_1 0x103c0
+/* [R 32] Parity register #0 read */
+#define NIG_REG_NIG_PRTY_STS 0x103d0
+/* [RW 1] Pause enable for port0. This register may get 1 only when
+ ~safc_enable.safc_enable = 0 and ppp_enable.ppp_enable =0 for the same
+ port */
+#define NIG_REG_PAUSE_ENABLE_0 0x160c0
/* [RW 1] Input enable for RX PBF LP IF */
#define NIG_REG_PBF_LB_IN_EN 0x100b4
+/* [RW 1] Value of this register will be transmitted to port swap when
+ ~nig_registers_strap_override.strap_override =1 */
+#define NIG_REG_PORT_SWAP 0x10394
/* [RW 1] output enable for RX parser descriptor IF */
#define NIG_REG_PRS_EOP_OUT_EN 0x10104
/* [RW 1] Input enable for RX parser request IF */
#define NIG_REG_PRS_REQ_IN_EN 0x100b8
+/* [RW 5] control to serdes - CL45 DEVAD */
+#define NIG_REG_SERDES0_CTRL_MD_DEVAD 0x10370
+/* [RW 1] control to serdes; 0 - clause 45; 1 - clause 22 */
+#define NIG_REG_SERDES0_CTRL_MD_ST 0x1036c
/* [RW 5] control to serdes - CL22 PHY_ADD and CL45 PRTAD */
#define NIG_REG_SERDES0_CTRL_PHY_ADDR 0x10374
/* [R 1] status from serdes0 that inputs to interrupt logic of link status */
/* [R 32] Rx statistics : In user packets discarded due to BRB backpressure
for port0 */
#define NIG_REG_STAT0_BRB_DISCARD 0x105f0
+/* [R 32] Rx statistics : In user packets truncated due to BRB backpressure
+ for port0 */
+#define NIG_REG_STAT0_BRB_TRUNCATE 0x105f8
+/* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that
+ between 1024 and 1522 bytes for port0 */
+#define NIG_REG_STAT0_EGRESS_MAC_PKT0 0x10750
+/* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that
+ between 1523 bytes and above for port0 */
+#define NIG_REG_STAT0_EGRESS_MAC_PKT1 0x10760
/* [R 32] Rx statistics : In user packets discarded due to BRB backpressure
for port1 */
#define NIG_REG_STAT1_BRB_DISCARD 0x10628
+/* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that
+ between 1024 and 1522 bytes for port1 */
+#define NIG_REG_STAT1_EGRESS_MAC_PKT0 0x107a0
+/* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that
+ between 1523 bytes and above for port1 */
+#define NIG_REG_STAT1_EGRESS_MAC_PKT1 0x107b0
/* [WB_R 64] Rx statistics : User octets received for LP */
#define NIG_REG_STAT2_BRB_OCTET 0x107e0
#define NIG_REG_STATUS_INTERRUPT_PORT0 0x10328
#define NIG_REG_STATUS_INTERRUPT_PORT1 0x1032c
+/* [RW 1] port swap mux selection. If this register equal to 0 then port
+ swap is equal to SPIO pin that inputs from ifmux_serdes_swap. If 1 then
+ ort swap is equal to ~nig_registers_port_swap.port_swap */
+#define NIG_REG_STRAP_OVERRIDE 0x10398
/* [RW 1] output enable for RX_XCM0 IF */
#define NIG_REG_XCM0_OUT_EN 0x100f0
/* [RW 1] output enable for RX_XCM1 IF */
#define NIG_REG_XCM1_OUT_EN 0x100f4
+/* [RW 1] control to xgxs - remote PHY in-band MDIO */
+#define NIG_REG_XGXS0_CTRL_EXTREMOTEMDIOST 0x10348
/* [RW 5] control to xgxs - CL45 DEVAD */
#define NIG_REG_XGXS0_CTRL_MD_DEVAD 0x1033c
+/* [RW 1] control to xgxs; 0 - clause 45; 1 - clause 22 */
+#define NIG_REG_XGXS0_CTRL_MD_ST 0x10338
/* [RW 5] control to xgxs - CL22 PHY_ADD and CL45 PRTAD */
#define NIG_REG_XGXS0_CTRL_PHY_ADDR 0x10340
/* [R 1] status from xgxs0 that inputs to interrupt logic of link10g. */
#define NIG_REG_XGXS_LANE_SEL_P0 0x102e8
/* [RW 1] selection for port0 for NIG_MUX block : 0 = SerDes; 1 = XGXS */
#define NIG_REG_XGXS_SERDES0_MODE_SEL 0x102e0
+#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT (0x1<<0)
#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS (0x1<<9)
#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G (0x1<<15)
#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS (0xf<<18)
#define PB_REG_PB_INT_STS 0x1c
/* [RW 4] Parity mask register #0 read/write */
#define PB_REG_PB_PRTY_MASK 0x38
+/* [R 4] Parity register #0 read */
+#define PB_REG_PB_PRTY_STS 0x2c
#define PRS_REG_A_PRSU_20 0x40134
/* [R 8] debug only: CFC load request current credit. Transaction based. */
#define PRS_REG_CFC_LD_CURRENT_CREDIT 0x40164
#define PRS_REG_CFC_SEARCH_INITIAL_CREDIT 0x4011c
/* [RW 24] CID for port 0 if no match */
#define PRS_REG_CID_PORT_0 0x400fc
-#define PRS_REG_CID_PORT_1 0x40100
/* [RW 32] The CM header for flush message where 'load existed' bit in CFC
load response is reset and packet type is 0. Used in packet start message
to TCM. */
#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_2 0x400e4
#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_3 0x400e8
#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_4 0x400ec
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_5 0x400f0
/* [RW 32] The CM header for flush message where 'load existed' bit in CFC
load response is set and packet type is 0. Used in packet start message
to TCM. */
#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_2 0x400c4
#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_3 0x400c8
#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_4 0x400cc
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_5 0x400d0
/* [RW 32] The CM header for a match and packet type 1 for loopback port.
Used in packet start message to TCM. */
#define PRS_REG_CM_HDR_LOOPBACK_TYPE_1 0x4009c
#define PRS_REG_CM_HDR_TYPE_4 0x40088
/* [RW 32] The CM header in case there was not a match on the connection */
#define PRS_REG_CM_NO_MATCH_HDR 0x400b8
+/* [RW 1] Indicates if in e1hov mode. 0=non-e1hov mode; 1=e1hov mode. */
+#define PRS_REG_E1HOV_MODE 0x401c8
/* [RW 8] The 8-bit event ID for a match and packet type 1. Used in packet
start message to TCM. */
#define PRS_REG_EVENT_ID_1 0x40054
#define PRS_REG_EVENT_ID_2 0x40058
#define PRS_REG_EVENT_ID_3 0x4005c
+/* [RW 16] The Ethernet type value for FCoE */
+#define PRS_REG_FCOE_TYPE 0x401d0
/* [RW 8] Context region for flush packet with packet type 0. Used in CFC
load request message. */
#define PRS_REG_FLUSH_REGIONS_TYPE_0 0x40004
#define PRS_REG_PRS_INT_STS 0x40188
/* [RW 8] Parity mask register #0 read/write */
#define PRS_REG_PRS_PRTY_MASK 0x401a4
+/* [R 8] Parity register #0 read */
+#define PRS_REG_PRS_PRTY_STS 0x40198
/* [RW 8] Context region for pure acknowledge packets. Used in CFC load
request message */
#define PRS_REG_PURE_REGIONS 0x40024
#define PXP2_REG_HST_DATA_FIFO_STATUS 0x12047c
/* [R 7] Debug only: Number of used entries in the header FIFO */
#define PXP2_REG_HST_HEADER_FIFO_STATUS 0x120478
+#define PXP2_REG_PGL_ADDR_88_F0 0x120534
+#define PXP2_REG_PGL_ADDR_8C_F0 0x120538
+#define PXP2_REG_PGL_ADDR_90_F0 0x12053c
+#define PXP2_REG_PGL_ADDR_94_F0 0x120540
#define PXP2_REG_PGL_CONTROL0 0x120490
#define PXP2_REG_PGL_CONTROL1 0x120514
+#define PXP2_REG_PGL_DEBUG 0x120520
+/* [RW 32] third dword data of expansion rom request. this register is
+ special. reading from it provides a vector outstanding read requests. if
+ a bit is zero it means that a read request on the corresponding tag did
+ not finish yet (not all completions have arrived for it) */
+#define PXP2_REG_PGL_EXP_ROM2 0x120808
/* [RW 32] Inbound interrupt table for CSDM: bits[31:16]-mask;
its[15:0]-address */
#define PXP2_REG_PGL_INT_CSDM_0 0x1204f4
#define PXP2_REG_PGL_INT_XSDM_5 0x1204e8
#define PXP2_REG_PGL_INT_XSDM_6 0x1204ec
#define PXP2_REG_PGL_INT_XSDM_7 0x1204f0
+/* [RW 3] this field allows one function to pretend being another function
+ when accessing any BAR mapped resource within the device. the value of
+ the field is the number of the function that will be accessed
+ effectively. after software write to this bit it must read it in order to
+ know that the new value is updated */
+#define PXP2_REG_PGL_PRETEND_FUNC_F0 0x120674
+#define PXP2_REG_PGL_PRETEND_FUNC_F1 0x120678
+#define PXP2_REG_PGL_PRETEND_FUNC_F2 0x12067c
+#define PXP2_REG_PGL_PRETEND_FUNC_F3 0x120680
+#define PXP2_REG_PGL_PRETEND_FUNC_F4 0x120684
+#define PXP2_REG_PGL_PRETEND_FUNC_F5 0x120688
+#define PXP2_REG_PGL_PRETEND_FUNC_F6 0x12068c
+#define PXP2_REG_PGL_PRETEND_FUNC_F7 0x120690
/* [R 1] this bit indicates that a read request was blocked because of
bus_master_en was deasserted */
#define PXP2_REG_PGL_READ_BLOCKED 0x120568
-/* [R 6] debug only */
-#define PXP2_REG_PGL_TXR_CDTS 0x120528
+#define PXP2_REG_PGL_TAGS_LIMIT 0x1205a8
/* [R 18] debug only */
#define PXP2_REG_PGL_TXW_CDTS 0x12052c
/* [R 1] this bit indicates that a write request was blocked because of
#define PXP2_REG_PSWRQ_BW_ADD1 0x1201c0
#define PXP2_REG_PSWRQ_BW_ADD10 0x1201e4
#define PXP2_REG_PSWRQ_BW_ADD11 0x1201e8
-#define PXP2_REG_PSWRQ_BW_ADD10 0x1201e4
-#define PXP2_REG_PSWRQ_BW_ADD11 0x1201e8
#define PXP2_REG_PSWRQ_BW_ADD2 0x1201c4
#define PXP2_REG_PSWRQ_BW_ADD28 0x120228
-#define PXP2_REG_PSWRQ_BW_ADD28 0x120228
#define PXP2_REG_PSWRQ_BW_ADD3 0x1201c8
#define PXP2_REG_PSWRQ_BW_ADD6 0x1201d4
#define PXP2_REG_PSWRQ_BW_ADD7 0x1201d8
#define PXP2_REG_PSWRQ_BW_L1 0x1202b0
#define PXP2_REG_PSWRQ_BW_L10 0x1202d4
#define PXP2_REG_PSWRQ_BW_L11 0x1202d8
-#define PXP2_REG_PSWRQ_BW_L10 0x1202d4
-#define PXP2_REG_PSWRQ_BW_L11 0x1202d8
#define PXP2_REG_PSWRQ_BW_L2 0x1202b4
#define PXP2_REG_PSWRQ_BW_L28 0x120318
-#define PXP2_REG_PSWRQ_BW_L28 0x120318
#define PXP2_REG_PSWRQ_BW_L3 0x1202b8
#define PXP2_REG_PSWRQ_BW_L6 0x1202c4
#define PXP2_REG_PSWRQ_BW_L7 0x1202c8
#define PXP2_REG_PSWRQ_BW_UB1 0x120238
#define PXP2_REG_PSWRQ_BW_UB10 0x12025c
#define PXP2_REG_PSWRQ_BW_UB11 0x120260
-#define PXP2_REG_PSWRQ_BW_UB10 0x12025c
-#define PXP2_REG_PSWRQ_BW_UB11 0x120260
#define PXP2_REG_PSWRQ_BW_UB2 0x12023c
#define PXP2_REG_PSWRQ_BW_UB28 0x1202a0
-#define PXP2_REG_PSWRQ_BW_UB28 0x1202a0
#define PXP2_REG_PSWRQ_BW_UB3 0x120240
#define PXP2_REG_PSWRQ_BW_UB6 0x12024c
#define PXP2_REG_PSWRQ_BW_UB7 0x120250
#define PXP2_REG_PSWRQ_QM0_L2P 0x120038
#define PXP2_REG_PSWRQ_SRC0_L2P 0x120054
#define PXP2_REG_PSWRQ_TM0_L2P 0x12001c
-/* [RW 25] Interrupt mask register #0 read/write */
-#define PXP2_REG_PXP2_INT_MASK 0x120578
-/* [R 25] Interrupt register #0 read */
-#define PXP2_REG_PXP2_INT_STS 0x12056c
-/* [RC 25] Interrupt register #0 read clear */
-#define PXP2_REG_PXP2_INT_STS_CLR 0x120570
+#define PXP2_REG_PSWRQ_TSDM0_L2P 0x1200e0
+/* [RW 32] Interrupt mask register #0 read/write */
+#define PXP2_REG_PXP2_INT_MASK_0 0x120578
+/* [R 32] Interrupt register #0 read */
+#define PXP2_REG_PXP2_INT_STS_0 0x12056c
+#define PXP2_REG_PXP2_INT_STS_1 0x120608
+/* [RC 32] Interrupt register #0 read clear */
+#define PXP2_REG_PXP2_INT_STS_CLR_0 0x120570
/* [RW 32] Parity mask register #0 read/write */
#define PXP2_REG_PXP2_PRTY_MASK_0 0x120588
#define PXP2_REG_PXP2_PRTY_MASK_1 0x120598
+/* [R 32] Parity register #0 read */
+#define PXP2_REG_PXP2_PRTY_STS_0 0x12057c
+#define PXP2_REG_PXP2_PRTY_STS_1 0x12058c
/* [R 1] Debug only: The 'almost full' indication from each fifo (gives
indication about backpressure) */
#define PXP2_REG_RD_ALMOST_FULL_0 0x120424
allocated for vq22 */
#define PXP2_REG_RD_MAX_BLKS_VQ22 0x1203d0
/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq25 */
+#define PXP2_REG_RD_MAX_BLKS_VQ25 0x1203dc
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
allocated for vq6 */
#define PXP2_REG_RD_MAX_BLKS_VQ6 0x120390
/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
#define PXP2_REG_RQ_BW_WR_UBOUND29 0x1202a4
/* [RW 7] Bandwidth upper bound for VQ30 */
#define PXP2_REG_RQ_BW_WR_UBOUND30 0x1202a8
+/* [RW 18] external first_mem_addr field in L2P table for CDU module port 0 */
+#define PXP2_REG_RQ_CDU0_EFIRST_MEM_ADDR 0x120008
/* [RW 2] Endian mode for cdu */
#define PXP2_REG_RQ_CDU_ENDIAN_M 0x1201a0
+#define PXP2_REG_RQ_CDU_FIRST_ILT 0x12061c
+#define PXP2_REG_RQ_CDU_LAST_ILT 0x120620
/* [RW 3] page size in L2P table for CDU module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_CDU_P_SIZE 0x120018
/* [RW 1] When '1'; requests will enter input buffers but wont get out
towards the glue */
#define PXP2_REG_RQ_DISABLE_INPUTS 0x120330
+/* [RW 1] 1 - SR will be aligned by 64B; 0 - SR will be aligned by 8B */
+#define PXP2_REG_RQ_DRAM_ALIGN 0x1205b0
+/* [RW 1] If 1 ILT failiue will not result in ELT access; An interrupt will
+ be asserted */
+#define PXP2_REG_RQ_ELT_DISABLE 0x12066c
/* [RW 2] Endian mode for hc */
#define PXP2_REG_RQ_HC_ENDIAN_M 0x1201a8
+/* [RW 1] when '0' ILT logic will work as in A0; otherwise B0; for back
+ compatibility needs; Note that different registers are used per mode */
+#define PXP2_REG_RQ_ILT_MODE 0x1205b4
/* [WB 53] Onchip address table */
#define PXP2_REG_RQ_ONCHIP_AT 0x122000
+/* [WB 53] Onchip address table - B0 */
+#define PXP2_REG_RQ_ONCHIP_AT_B0 0x128000
+/* [RW 13] Pending read limiter threshold; in Dwords */
+#define PXP2_REG_RQ_PDR_LIMIT 0x12033c
/* [RW 2] Endian mode for qm */
#define PXP2_REG_RQ_QM_ENDIAN_M 0x120194
+#define PXP2_REG_RQ_QM_FIRST_ILT 0x120634
+#define PXP2_REG_RQ_QM_LAST_ILT 0x120638
/* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_QM_P_SIZE 0x120050
-/* [RW 1] 1' indicates that the RBC has finished configurating the PSWRQ */
+/* [RW 1] 1' indicates that the RBC has finished configuring the PSWRQ */
#define PXP2_REG_RQ_RBC_DONE 0x1201b0
/* [RW 3] Max burst size filed for read requests port 0; 000 - 128B;
001:256B; 010: 512B; 11:1K:100:2K; 01:4K */
#define PXP2_REG_RQ_RD_MBS0 0x120160
+/* [RW 3] Max burst size filed for read requests port 1; 000 - 128B;
+ 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */
+#define PXP2_REG_RQ_RD_MBS1 0x120168
/* [RW 2] Endian mode for src */
#define PXP2_REG_RQ_SRC_ENDIAN_M 0x12019c
+#define PXP2_REG_RQ_SRC_FIRST_ILT 0x12063c
+#define PXP2_REG_RQ_SRC_LAST_ILT 0x120640
/* [RW 3] page size in L2P table for SRC module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_SRC_P_SIZE 0x12006c
/* [RW 2] Endian mode for tm */
#define PXP2_REG_RQ_TM_ENDIAN_M 0x120198
+#define PXP2_REG_RQ_TM_FIRST_ILT 0x120644
+#define PXP2_REG_RQ_TM_LAST_ILT 0x120648
/* [RW 3] page size in L2P table for TM module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_TM_P_SIZE 0x120034
/* [R 5] Number of entries in the ufifo; his fifo has l2p completions */
#define PXP2_REG_RQ_UFIFO_NUM_OF_ENTRY 0x12080c
+/* [RW 18] external first_mem_addr field in L2P table for USDM module port 0 */
+#define PXP2_REG_RQ_USDM0_EFIRST_MEM_ADDR 0x120094
/* [R 8] Number of entries occupied by vq 0 in pswrq memory */
#define PXP2_REG_RQ_VQ0_ENTRY_CNT 0x120810
/* [R 8] Number of entries occupied by vq 10 in pswrq memory */
/* [RW 3] Max burst size filed for write requests port 0; 000 - 128B;
001:256B; 010: 512B; */
#define PXP2_REG_RQ_WR_MBS0 0x12015c
-/* [RW 10] if Number of entries in dmae fifo will be higer than this
+/* [RW 3] Max burst size filed for write requests port 1; 000 - 128B;
+ 001:256B; 010: 512B; */
+#define PXP2_REG_RQ_WR_MBS1 0x120164
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_CDU_MPS 0x1205f0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_CSDM_MPS 0x1205d0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_DBG_MPS 0x1205e8
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_DMAE_MPS 0x1205ec
+/* [RW 10] if Number of entries in dmae fifo will be higher than this
threshold then has_payload indication will be asserted; the default value
should be equal to > write MBS size! */
#define PXP2_REG_WR_DMAE_TH 0x120368
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_HC_MPS 0x1205c8
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_QM_MPS 0x1205dc
+/* [RW 1] 0 - working in A0 mode; - working in B0 mode */
+#define PXP2_REG_WR_REV_MODE 0x120670
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_SRC_MPS 0x1205e4
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_TM_MPS 0x1205e0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_TSDM_MPS 0x1205d4
+/* [RW 10] if Number of entries in usdmdp fifo will be higher than this
+ threshold then has_payload indication will be asserted; the default value
+ should be equal to > write MBS size! */
+#define PXP2_REG_WR_USDMDP_TH 0x120348
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_USDM_MPS 0x1205cc
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_XSDM_MPS 0x1205d8
/* [R 1] debug only: Indication if PSWHST arbiter is idle */
#define PXP_REG_HST_ARB_IS_IDLE 0x103004
/* [R 8] debug only: A bit mask for all PSWHST arbiter clients. '1' means
this client is waiting for the arbiter. */
#define PXP_REG_HST_CLIENTS_WAITING_TO_ARB 0x103008
+/* [R 1] debug only: '1' means this PSWHST is discarding doorbells. This bit
+ should update accoring to 'hst_discard_doorbells' register when the state
+ machine is idle */
+#define PXP_REG_HST_DISCARD_DOORBELLS_STATUS 0x1030a0
+/* [R 6] debug only: A bit mask for all PSWHST internal write clients. '1'
+ means this PSWHST is discarding inputs from this client. Each bit should
+ update accoring to 'hst_discard_internal_writes' register when the state
+ machine is idle. */
+#define PXP_REG_HST_DISCARD_INTERNAL_WRITES_STATUS 0x10309c
/* [WB 160] Used for initialization of the inbound interrupts memory */
#define PXP_REG_HST_INBOUND_INT 0x103800
/* [RW 32] Interrupt mask register #0 read/write */
#define PXP_REG_PXP_INT_STS_CLR_0 0x10306c
/* [RW 26] Parity mask register #0 read/write */
#define PXP_REG_PXP_PRTY_MASK 0x103094
+/* [R 26] Parity register #0 read */
+#define PXP_REG_PXP_PRTY_STS 0x103088
/* [RW 4] The activity counter initial increment value sent in the load
request */
#define QM_REG_ACTCTRINITVAL_0 0x168040
#define QM_REG_ACTCTRINITVAL_3 0x16804c
/* [RW 32] The base logical address (in bytes) of each physical queue. The
index I represents the physical queue number. The 12 lsbs are ignore and
- considered zero so practically there are only 20 bits in this register. */
+ considered zero so practically there are only 20 bits in this register;
+ queues 63-0 */
#define QM_REG_BASEADDR 0x168900
+/* [RW 32] The base logical address (in bytes) of each physical queue. The
+ index I represents the physical queue number. The 12 lsbs are ignore and
+ considered zero so practically there are only 20 bits in this register;
+ queues 127-64 */
+#define QM_REG_BASEADDR_EXT_A 0x16e100
/* [RW 16] The byte credit cost for each task. This value is for both ports */
#define QM_REG_BYTECRDCOST 0x168234
/* [RW 16] The initial byte credit value for both ports. */
#define QM_REG_BYTECRDINITVAL 0x168238
/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
- queue uses port 0 else it uses port 1. */
+ queue uses port 0 else it uses port 1; queues 31-0 */
#define QM_REG_BYTECRDPORT_LSB 0x168228
/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
- queue uses port 0 else it uses port 1. */
+ queue uses port 0 else it uses port 1; queues 95-64 */
+#define QM_REG_BYTECRDPORT_LSB_EXT_A 0x16e520
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 63-32 */
#define QM_REG_BYTECRDPORT_MSB 0x168224
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 127-96 */
+#define QM_REG_BYTECRDPORT_MSB_EXT_A 0x16e51c
/* [RW 16] The byte credit value that if above the QM is considered almost
full */
#define QM_REG_BYTECREDITAFULLTHR 0x168094
#define QM_REG_CMINTVOQMASK_6 0x16820c
#define QM_REG_CMINTVOQMASK_7 0x168210
/* [RW 20] The number of connections divided by 16 which dictates the size
- of each queue per port 0 */
+ of each queue which belongs to even function number. */
#define QM_REG_CONNNUM_0 0x168020
/* [R 6] Keep the fill level of the fifo from write client 4 */
#define QM_REG_CQM_WRC_FIFOLVL 0x168018
bypass enable */
#define QM_REG_ENBYPVOQMASK 0x16823c
/* [RW 32] A bit mask per each physical queue. If a bit is set then the
- physical queue uses the byte credit */
+ physical queue uses the byte credit; queues 31-0 */
#define QM_REG_ENBYTECRD_LSB 0x168220
/* [RW 32] A bit mask per each physical queue. If a bit is set then the
- physical queue uses the byte credit */
+ physical queue uses the byte credit; queues 95-64 */
+#define QM_REG_ENBYTECRD_LSB_EXT_A 0x16e518
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 63-32 */
#define QM_REG_ENBYTECRD_MSB 0x16821c
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 127-96 */
+#define QM_REG_ENBYTECRD_MSB_EXT_A 0x16e514
/* [RW 4] If cleared then the secondary interface will not be served by the
RR arbiter */
#define QM_REG_ENSEC 0x1680f0
-/* [RW 32] A bit vector per each physical queue which selects which function
- number to use on PCI access for that queue. */
+/* [RW 32] NA */
#define QM_REG_FUNCNUMSEL_LSB 0x168230
-/* [RW 32] A bit vector per each physical queue which selects which function
- number to use on PCI access for that queue. */
+/* [RW 32] NA */
#define QM_REG_FUNCNUMSEL_MSB 0x16822c
/* [RW 32] A mask register to mask the Almost empty signals which will not
- be use for the almost empty indication to the HW block */
+ be use for the almost empty indication to the HW block; queues 31:0 */
#define QM_REG_HWAEMPTYMASK_LSB 0x168218
/* [RW 32] A mask register to mask the Almost empty signals which will not
- be use for the almost empty indication to the HW block */
+ be use for the almost empty indication to the HW block; queues 95-64 */
+#define QM_REG_HWAEMPTYMASK_LSB_EXT_A 0x16e510
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 63:32 */
#define QM_REG_HWAEMPTYMASK_MSB 0x168214
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 127-96 */
+#define QM_REG_HWAEMPTYMASK_MSB_EXT_A 0x16e50c
/* [RW 4] The number of outstanding request to CFC */
#define QM_REG_OUTLDREQ 0x168804
/* [RC 1] A flag to indicate that overflow error occurred in one of the
queues. */
#define QM_REG_OVFERROR 0x16805c
-/* [RC 6] the Q were the qverflow occurs */
+/* [RC 7] the Q where the overflow occurs */
#define QM_REG_OVFQNUM 0x168058
-/* [R 32] Pause state for physical queues 31-0 */
+/* [R 16] Pause state for physical queues 15-0 */
#define QM_REG_PAUSESTATE0 0x168410
-/* [R 32] Pause state for physical queues 64-32 */
+/* [R 16] Pause state for physical queues 31-16 */
#define QM_REG_PAUSESTATE1 0x168414
+/* [R 16] Pause state for physical queues 47-32 */
+#define QM_REG_PAUSESTATE2 0x16e684
+/* [R 16] Pause state for physical queues 63-48 */
+#define QM_REG_PAUSESTATE3 0x16e688
+/* [R 16] Pause state for physical queues 79-64 */
+#define QM_REG_PAUSESTATE4 0x16e68c
+/* [R 16] Pause state for physical queues 95-80 */
+#define QM_REG_PAUSESTATE5 0x16e690
+/* [R 16] Pause state for physical queues 111-96 */
+#define QM_REG_PAUSESTATE6 0x16e694
+/* [R 16] Pause state for physical queues 127-112 */
+#define QM_REG_PAUSESTATE7 0x16e698
/* [RW 2] The PCI attributes field used in the PCI request. */
#define QM_REG_PCIREQAT 0x168054
/* [R 16] The byte credit of port 0 */
#define QM_REG_PORT0BYTECRD 0x168300
/* [R 16] The byte credit of port 1 */
#define QM_REG_PORT1BYTECRD 0x168304
-/* [WB 54] Pointer Table Memory; The mapping is as follow: ptrtbl[53:30]
- read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read bank0;
- ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
+/* [RW 3] pci function number of queues 15-0 */
+#define QM_REG_PQ2PCIFUNC_0 0x16e6bc
+#define QM_REG_PQ2PCIFUNC_1 0x16e6c0
+#define QM_REG_PQ2PCIFUNC_2 0x16e6c4
+#define QM_REG_PQ2PCIFUNC_3 0x16e6c8
+#define QM_REG_PQ2PCIFUNC_4 0x16e6cc
+#define QM_REG_PQ2PCIFUNC_5 0x16e6d0
+#define QM_REG_PQ2PCIFUNC_6 0x16e6d4
+#define QM_REG_PQ2PCIFUNC_7 0x16e6d8
+/* [WB 54] Pointer Table Memory for queues 63-0; The mapping is as follow:
+ ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read
+ bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
#define QM_REG_PTRTBL 0x168a00
+/* [WB 54] Pointer Table Memory for queues 127-64; The mapping is as follow:
+ ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read
+ bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
+#define QM_REG_PTRTBL_EXT_A 0x16e200
/* [RW 2] Interrupt mask register #0 read/write */
#define QM_REG_QM_INT_MASK 0x168444
/* [R 2] Interrupt register #0 read */
#define QM_REG_QM_INT_STS 0x168438
-/* [RW 9] Parity mask register #0 read/write */
+/* [RW 12] Parity mask register #0 read/write */
#define QM_REG_QM_PRTY_MASK 0x168454
+/* [R 12] Parity register #0 read */
+#define QM_REG_QM_PRTY_STS 0x168448
/* [R 32] Current queues in pipeline: Queues from 32 to 63 */
#define QM_REG_QSTATUS_HIGH 0x16802c
+/* [R 32] Current queues in pipeline: Queues from 96 to 127 */
+#define QM_REG_QSTATUS_HIGH_EXT_A 0x16e408
/* [R 32] Current queues in pipeline: Queues from 0 to 31 */
#define QM_REG_QSTATUS_LOW 0x168028
-/* [R 24] The number of tasks queued for each queue */
+/* [R 32] Current queues in pipeline: Queues from 64 to 95 */
+#define QM_REG_QSTATUS_LOW_EXT_A 0x16e404
+/* [R 24] The number of tasks queued for each queue; queues 63-0 */
#define QM_REG_QTASKCTR_0 0x168308
+/* [R 24] The number of tasks queued for each queue; queues 127-64 */
+#define QM_REG_QTASKCTR_EXT_A_0 0x16e584
/* [RW 4] Queue tied to VOQ */
#define QM_REG_QVOQIDX_0 0x1680f4
#define QM_REG_QVOQIDX_10 0x16811c
+#define QM_REG_QVOQIDX_100 0x16e49c
+#define QM_REG_QVOQIDX_101 0x16e4a0
+#define QM_REG_QVOQIDX_102 0x16e4a4
+#define QM_REG_QVOQIDX_103 0x16e4a8
+#define QM_REG_QVOQIDX_104 0x16e4ac
+#define QM_REG_QVOQIDX_105 0x16e4b0
+#define QM_REG_QVOQIDX_106 0x16e4b4
+#define QM_REG_QVOQIDX_107 0x16e4b8
+#define QM_REG_QVOQIDX_108 0x16e4bc
+#define QM_REG_QVOQIDX_109 0x16e4c0
#define QM_REG_QVOQIDX_11 0x168120
+#define QM_REG_QVOQIDX_110 0x16e4c4
+#define QM_REG_QVOQIDX_111 0x16e4c8
+#define QM_REG_QVOQIDX_112 0x16e4cc
+#define QM_REG_QVOQIDX_113 0x16e4d0
+#define QM_REG_QVOQIDX_114 0x16e4d4
+#define QM_REG_QVOQIDX_115 0x16e4d8
+#define QM_REG_QVOQIDX_116 0x16e4dc
+#define QM_REG_QVOQIDX_117 0x16e4e0
+#define QM_REG_QVOQIDX_118 0x16e4e4
+#define QM_REG_QVOQIDX_119 0x16e4e8
#define QM_REG_QVOQIDX_12 0x168124
+#define QM_REG_QVOQIDX_120 0x16e4ec
+#define QM_REG_QVOQIDX_121 0x16e4f0
+#define QM_REG_QVOQIDX_122 0x16e4f4
+#define QM_REG_QVOQIDX_123 0x16e4f8
+#define QM_REG_QVOQIDX_124 0x16e4fc
+#define QM_REG_QVOQIDX_125 0x16e500
+#define QM_REG_QVOQIDX_126 0x16e504
+#define QM_REG_QVOQIDX_127 0x16e508
#define QM_REG_QVOQIDX_13 0x168128
#define QM_REG_QVOQIDX_14 0x16812c
#define QM_REG_QVOQIDX_15 0x168130
#define QM_REG_QVOQIDX_16 0x168134
#define QM_REG_QVOQIDX_17 0x168138
#define QM_REG_QVOQIDX_21 0x168148
+#define QM_REG_QVOQIDX_22 0x16814c
+#define QM_REG_QVOQIDX_23 0x168150
+#define QM_REG_QVOQIDX_24 0x168154
#define QM_REG_QVOQIDX_25 0x168158
+#define QM_REG_QVOQIDX_26 0x16815c
+#define QM_REG_QVOQIDX_27 0x168160
+#define QM_REG_QVOQIDX_28 0x168164
#define QM_REG_QVOQIDX_29 0x168168
+#define QM_REG_QVOQIDX_30 0x16816c
+#define QM_REG_QVOQIDX_31 0x168170
#define QM_REG_QVOQIDX_32 0x168174
#define QM_REG_QVOQIDX_33 0x168178
#define QM_REG_QVOQIDX_34 0x16817c
#define QM_REG_QVOQIDX_57 0x1681d8
#define QM_REG_QVOQIDX_58 0x1681dc
#define QM_REG_QVOQIDX_59 0x1681e0
-#define QM_REG_QVOQIDX_50 0x1681bc
-#define QM_REG_QVOQIDX_51 0x1681c0
-#define QM_REG_QVOQIDX_52 0x1681c4
-#define QM_REG_QVOQIDX_53 0x1681c8
-#define QM_REG_QVOQIDX_54 0x1681cc
-#define QM_REG_QVOQIDX_55 0x1681d0
-#define QM_REG_QVOQIDX_56 0x1681d4
-#define QM_REG_QVOQIDX_57 0x1681d8
-#define QM_REG_QVOQIDX_58 0x1681dc
-#define QM_REG_QVOQIDX_59 0x1681e0
#define QM_REG_QVOQIDX_6 0x16810c
#define QM_REG_QVOQIDX_60 0x1681e4
#define QM_REG_QVOQIDX_61 0x1681e8
#define QM_REG_QVOQIDX_62 0x1681ec
#define QM_REG_QVOQIDX_63 0x1681f0
-#define QM_REG_QVOQIDX_60 0x1681e4
-#define QM_REG_QVOQIDX_61 0x1681e8
-#define QM_REG_QVOQIDX_62 0x1681ec
-#define QM_REG_QVOQIDX_63 0x1681f0
+#define QM_REG_QVOQIDX_64 0x16e40c
+#define QM_REG_QVOQIDX_65 0x16e410
+#define QM_REG_QVOQIDX_69 0x16e420
#define QM_REG_QVOQIDX_7 0x168110
+#define QM_REG_QVOQIDX_70 0x16e424
+#define QM_REG_QVOQIDX_71 0x16e428
+#define QM_REG_QVOQIDX_72 0x16e42c
+#define QM_REG_QVOQIDX_73 0x16e430
+#define QM_REG_QVOQIDX_74 0x16e434
+#define QM_REG_QVOQIDX_75 0x16e438
+#define QM_REG_QVOQIDX_76 0x16e43c
+#define QM_REG_QVOQIDX_77 0x16e440
+#define QM_REG_QVOQIDX_78 0x16e444
+#define QM_REG_QVOQIDX_79 0x16e448
#define QM_REG_QVOQIDX_8 0x168114
+#define QM_REG_QVOQIDX_80 0x16e44c
+#define QM_REG_QVOQIDX_81 0x16e450
+#define QM_REG_QVOQIDX_85 0x16e460
+#define QM_REG_QVOQIDX_86 0x16e464
+#define QM_REG_QVOQIDX_87 0x16e468
+#define QM_REG_QVOQIDX_88 0x16e46c
+#define QM_REG_QVOQIDX_89 0x16e470
#define QM_REG_QVOQIDX_9 0x168118
-/* [R 24] Remaining pause timeout for port 0 */
-#define QM_REG_REMAINPAUSETM0 0x168418
-/* [R 24] Remaining pause timeout for port 1 */
-#define QM_REG_REMAINPAUSETM1 0x16841c
+#define QM_REG_QVOQIDX_90 0x16e474
+#define QM_REG_QVOQIDX_91 0x16e478
+#define QM_REG_QVOQIDX_92 0x16e47c
+#define QM_REG_QVOQIDX_93 0x16e480
+#define QM_REG_QVOQIDX_94 0x16e484
+#define QM_REG_QVOQIDX_95 0x16e488
+#define QM_REG_QVOQIDX_96 0x16e48c
+#define QM_REG_QVOQIDX_97 0x16e490
+#define QM_REG_QVOQIDX_98 0x16e494
+#define QM_REG_QVOQIDX_99 0x16e498
/* [RW 1] Initialization bit command */
#define QM_REG_SOFT_RESET 0x168428
/* [RW 8] The credit cost per every task in the QM. A value per each VOQ */
#define QM_REG_TASKCRDCOST_0 0x16809c
#define QM_REG_TASKCRDCOST_1 0x1680a0
-#define QM_REG_TASKCRDCOST_10 0x1680c4
-#define QM_REG_TASKCRDCOST_11 0x1680c8
#define QM_REG_TASKCRDCOST_2 0x1680a4
#define QM_REG_TASKCRDCOST_4 0x1680ac
#define QM_REG_TASKCRDCOST_5 0x1680b0
/* [R 16] The credit value for each VOQ */
#define QM_REG_VOQCREDIT_0 0x1682d0
#define QM_REG_VOQCREDIT_1 0x1682d4
-#define QM_REG_VOQCREDIT_10 0x1682f8
-#define QM_REG_VOQCREDIT_11 0x1682fc
#define QM_REG_VOQCREDIT_4 0x1682e0
/* [RW 16] The credit value that if above the QM is considered almost full */
#define QM_REG_VOQCREDITAFULLTHR 0x168090
/* [RW 16] The init and maximum credit for each VoQ */
#define QM_REG_VOQINITCREDIT_0 0x168060
#define QM_REG_VOQINITCREDIT_1 0x168064
-#define QM_REG_VOQINITCREDIT_10 0x168088
-#define QM_REG_VOQINITCREDIT_11 0x16808c
#define QM_REG_VOQINITCREDIT_2 0x168068
#define QM_REG_VOQINITCREDIT_4 0x168070
#define QM_REG_VOQINITCREDIT_5 0x168074
/* [RW 1] The port of which VOQ belongs */
+#define QM_REG_VOQPORT_0 0x1682a0
#define QM_REG_VOQPORT_1 0x1682a4
-#define QM_REG_VOQPORT_10 0x1682c8
-#define QM_REG_VOQPORT_11 0x1682cc
#define QM_REG_VOQPORT_2 0x1682a8
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_0_LSB 0x168240
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_0_LSB_EXT_A 0x16e524
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_0_MSB 0x168244
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_0_MSB_EXT_A 0x16e528
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_10_LSB 0x168290
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_10_LSB_EXT_A 0x16e574
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_10_MSB 0x168294
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_10_MSB_EXT_A 0x16e578
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_11_LSB 0x168298
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_11_LSB_EXT_A 0x16e57c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_11_MSB 0x16829c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_11_MSB_EXT_A 0x16e580
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_1_LSB 0x168248
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_1_LSB_EXT_A 0x16e52c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_1_MSB 0x16824c
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_1_MSB_EXT_A 0x16e530
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_2_LSB 0x168250
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_2_LSB_EXT_A 0x16e534
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_2_MSB 0x168254
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_2_MSB_EXT_A 0x16e538
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_3_LSB 0x168258
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_3_LSB_EXT_A 0x16e53c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_3_MSB_EXT_A 0x16e540
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_4_LSB 0x168260
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_4_LSB_EXT_A 0x16e544
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_4_MSB 0x168264
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_4_MSB_EXT_A 0x16e548
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_5_LSB 0x168268
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_5_LSB_EXT_A 0x16e54c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_5_MSB 0x16826c
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_5_MSB_EXT_A 0x16e550
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_6_LSB 0x168270
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_6_LSB_EXT_A 0x16e554
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_6_MSB 0x168274
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_6_MSB_EXT_A 0x16e558
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_7_LSB 0x168278
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_7_LSB_EXT_A 0x16e55c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_7_MSB 0x16827c
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_7_MSB_EXT_A 0x16e560
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_8_LSB 0x168280
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_8_LSB_EXT_A 0x16e564
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_8_MSB 0x168284
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_8_MSB_EXT_A 0x16e568
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_9_LSB 0x168288
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_9_LSB_EXT_A 0x16e56c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_9_MSB_EXT_A 0x16e570
/* [RW 32] Wrr weights */
#define QM_REG_WRRWEIGHTS_0 0x16880c
#define QM_REG_WRRWEIGHTS_1 0x168810
#define QM_REG_WRRWEIGHTS_10 0x168814
-#define QM_REG_WRRWEIGHTS_10_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_11 0x168818
-#define QM_REG_WRRWEIGHTS_11_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_12 0x16881c
-#define QM_REG_WRRWEIGHTS_12_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_13 0x168820
-#define QM_REG_WRRWEIGHTS_13_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_14 0x168824
-#define QM_REG_WRRWEIGHTS_14_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_15 0x168828
-#define QM_REG_WRRWEIGHTS_15_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_10 0x168814
#define QM_REG_WRRWEIGHTS_11 0x168818
#define QM_REG_WRRWEIGHTS_12 0x16881c
#define QM_REG_WRRWEIGHTS_13 0x168820
#define QM_REG_WRRWEIGHTS_14 0x168824
#define QM_REG_WRRWEIGHTS_15 0x168828
+#define QM_REG_WRRWEIGHTS_16 0x16e000
+#define QM_REG_WRRWEIGHTS_17 0x16e004
+#define QM_REG_WRRWEIGHTS_18 0x16e008
+#define QM_REG_WRRWEIGHTS_19 0x16e00c
#define QM_REG_WRRWEIGHTS_2 0x16882c
+#define QM_REG_WRRWEIGHTS_20 0x16e010
+#define QM_REG_WRRWEIGHTS_21 0x16e014
+#define QM_REG_WRRWEIGHTS_22 0x16e018
+#define QM_REG_WRRWEIGHTS_23 0x16e01c
+#define QM_REG_WRRWEIGHTS_24 0x16e020
+#define QM_REG_WRRWEIGHTS_25 0x16e024
+#define QM_REG_WRRWEIGHTS_26 0x16e028
+#define QM_REG_WRRWEIGHTS_27 0x16e02c
+#define QM_REG_WRRWEIGHTS_28 0x16e030
+#define QM_REG_WRRWEIGHTS_29 0x16e034
#define QM_REG_WRRWEIGHTS_3 0x168830
+#define QM_REG_WRRWEIGHTS_30 0x16e038
+#define QM_REG_WRRWEIGHTS_31 0x16e03c
#define QM_REG_WRRWEIGHTS_4 0x168834
#define QM_REG_WRRWEIGHTS_5 0x168838
#define QM_REG_WRRWEIGHTS_6 0x16883c
#define QM_REG_WRRWEIGHTS_9 0x168848
/* [R 6] Keep the fill level of the fifo from write client 1 */
#define QM_REG_XQM_WRC_FIFOLVL 0x168000
-#define DORQ_DORQ_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
-#define DORQ_DORQ_INT_STS_REG_ADDRESS_ERROR_SIZE 0
-#define DORQ_DORQ_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
-#define DORQ_DORQ_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
-#define DORQ_DORQ_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
-#define DORQ_DORQ_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
-#define DORQ_DORQ_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
-#define DORQ_DORQ_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
-#define NIG_NIG_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
-#define NIG_NIG_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
-#define NIG_NIG_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
-#define NIG_NIG_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
-#define NIG_NIG_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
-#define NIG_NIG_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
-#define NIG_NIG_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
-#define NIG_NIG_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
-#define TCM_TCM_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
-#define TCM_TCM_INT_STS_REG_ADDRESS_ERROR_SIZE 0
-#define TCM_TCM_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
-#define TCM_TCM_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
-#define TCM_TCM_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
-#define TCM_TCM_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
-#define TCM_TCM_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
-#define TCM_TCM_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
-#define CFC_DEBUG1_REG_WRITE_AC (0x1<<4)
-#define CFC_DEBUG1_REG_WRITE_AC_SIZE 4
-/* [R 1] debug only: This bit indicates wheter indicates that external
- buffer was wrapped (oldest data was thrown); Relevant only when
- ~dbg_registers_debug_target=2 (PCI) & ~dbg_registers_full_mode=1 (wrap); */
-#define DBG_REG_WRAP_ON_EXT_BUFFER 0xc124
-#define DBG_REG_WRAP_ON_EXT_BUFFER_SIZE 1
-/* [R 1] debug only: This bit indicates wheter the internal buffer was
- wrapped (oldest data was thrown) Relevant only when
- ~dbg_registers_debug_target=0 (internal buffer) */
-#define DBG_REG_WRAP_ON_INT_BUFFER 0xc128
-#define DBG_REG_WRAP_ON_INT_BUFFER_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_0 0x16880c
-#define QM_REG_WRRWEIGHTS_0_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_1 0x168810
-#define QM_REG_WRRWEIGHTS_1_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_10 0x168814
-#define QM_REG_WRRWEIGHTS_10_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_11 0x168818
-#define QM_REG_WRRWEIGHTS_11_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_12 0x16881c
-#define QM_REG_WRRWEIGHTS_12_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_13 0x168820
-#define QM_REG_WRRWEIGHTS_13_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_14 0x168824
-#define QM_REG_WRRWEIGHTS_14_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_15 0x168828
-#define QM_REG_WRRWEIGHTS_15_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_2 0x16882c
-#define QM_REG_WRRWEIGHTS_2_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_3 0x168830
-#define QM_REG_WRRWEIGHTS_3_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_4 0x168834
-#define QM_REG_WRRWEIGHTS_4_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_5 0x168838
-#define QM_REG_WRRWEIGHTS_5_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_6 0x16883c
-#define QM_REG_WRRWEIGHTS_6_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_7 0x168840
-#define QM_REG_WRRWEIGHTS_7_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_8 0x168844
-#define QM_REG_WRRWEIGHTS_8_SIZE 1
-/* [RW 32] Wrr weights */
-#define QM_REG_WRRWEIGHTS_9 0x168848
-#define QM_REG_WRRWEIGHTS_9_SIZE 1
-/* [RW 22] Number of free element in the free list of T2 entries - port 0. */
#define SRC_REG_COUNTFREE0 0x40500
-/* [WB 64] First free element in the free list of T2 entries - port 0. */
+/* [RW 1] If clr the searcher is compatible to E1 A0 - support only two
+ ports. If set the searcher support 8 functions. */
+#define SRC_REG_E1HMF_ENABLE 0x404cc
#define SRC_REG_FIRSTFREE0 0x40510
#define SRC_REG_KEYRSS0_0 0x40408
+#define SRC_REG_KEYRSS0_7 0x40424
#define SRC_REG_KEYRSS1_9 0x40454
-/* [WB 64] Last free element in the free list of T2 entries - port 0. */
+#define SRC_REG_KEYSEARCH_0 0x40458
+#define SRC_REG_KEYSEARCH_1 0x4045c
+#define SRC_REG_KEYSEARCH_2 0x40460
+#define SRC_REG_KEYSEARCH_3 0x40464
+#define SRC_REG_KEYSEARCH_4 0x40468
+#define SRC_REG_KEYSEARCH_5 0x4046c
+#define SRC_REG_KEYSEARCH_6 0x40470
+#define SRC_REG_KEYSEARCH_7 0x40474
+#define SRC_REG_KEYSEARCH_8 0x40478
+#define SRC_REG_KEYSEARCH_9 0x4047c
#define SRC_REG_LASTFREE0 0x40530
-/* [RW 5] The number of hash bits used for the search (h); Values can be 8
- to 24. */
#define SRC_REG_NUMBER_HASH_BITS0 0x40400
/* [RW 1] Reset internal state machines. */
#define SRC_REG_SOFT_RST 0x4049c
-/* [R 1] Interrupt register #0 read */
+/* [R 3] Interrupt register #0 read */
#define SRC_REG_SRC_INT_STS 0x404ac
/* [RW 3] Parity mask register #0 read/write */
#define SRC_REG_SRC_PRTY_MASK 0x404c8
+/* [R 3] Parity register #0 read */
+#define SRC_REG_SRC_PRTY_STS 0x404bc
/* [R 4] Used to read the value of the XX protection CAM occupancy counter. */
#define TCM_REG_CAM_OCCUP 0x5017c
/* [RW 1] CDU AG read Interface enable. If 0 - the request input is
/* [RC 1] Message length mismatch (relative to last indication) at the In#9
interface. */
#define TCM_REG_CSEM_LENGTH_MIS 0x50174
+/* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_CSEM_WEIGHT 0x500bc
/* [RW 8] The Event ID in case of ErrorFlg is set in the input message. */
#define TCM_REG_ERR_EVNT_ID 0x500a0
/* [RW 28] The CM erroneous header for QM and Timers formatting. */
type (one of 16). */
#define TCM_REG_N_SM_CTX_LD_0 0x50050
#define TCM_REG_N_SM_CTX_LD_1 0x50054
-#define TCM_REG_N_SM_CTX_LD_10 0x50078
-#define TCM_REG_N_SM_CTX_LD_11 0x5007c
-#define TCM_REG_N_SM_CTX_LD_12 0x50080
-#define TCM_REG_N_SM_CTX_LD_13 0x50084
-#define TCM_REG_N_SM_CTX_LD_14 0x50088
-#define TCM_REG_N_SM_CTX_LD_15 0x5008c
#define TCM_REG_N_SM_CTX_LD_2 0x50058
#define TCM_REG_N_SM_CTX_LD_3 0x5005c
#define TCM_REG_N_SM_CTX_LD_4 0x50060
+#define TCM_REG_N_SM_CTX_LD_5 0x50064
/* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define TCM_REG_PBF_WEIGHT 0x500b4
-/* [RW 6] The physical queue number 0 per port index. */
#define TCM_REG_PHYS_QNUM0_0 0x500e0
#define TCM_REG_PHYS_QNUM0_1 0x500e4
-/* [RW 6] The physical queue number 1 per port index. */
#define TCM_REG_PHYS_QNUM1_0 0x500e8
+#define TCM_REG_PHYS_QNUM1_1 0x500ec
+#define TCM_REG_PHYS_QNUM2_0 0x500f0
+#define TCM_REG_PHYS_QNUM2_1 0x500f4
+#define TCM_REG_PHYS_QNUM3_0 0x500f8
+#define TCM_REG_PHYS_QNUM3_1 0x500fc
/* [RW 1] Input prs Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define TCM_REG_STORM_TCM_IFEN 0x50010
+/* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_STORM_WEIGHT 0x500ac
/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
#define TCM_REG_TCM_INT_MASK 0x501dc
/* [R 11] Interrupt register #0 read */
#define TCM_REG_TCM_INT_STS 0x501d0
+/* [R 27] Parity register #0 read */
+#define TCM_REG_TCM_PRTY_STS 0x501e0
/* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define TCM_REG_TM_TCM_IFEN 0x5001c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TM_WEIGHT 0x500d0
/* [RW 6] QM output initial credit. Max credit available - 32.Write writes
the initial credit value; read returns the current value of the credit
counter. Must be initialized to 32 at start-up. */
#define TCM_REG_TQM_INIT_CRD 0x5021c
+/* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TQM_P_WEIGHT 0x500c8
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TQM_S_WEIGHT 0x500cc
/* [RW 28] The CM header value for QM request (primary). */
#define TCM_REG_TQM_TCM_HDR_P 0x50090
/* [RW 28] The CM header value for QM request (secondary). */
/* [RC 1] Message length mismatch (relative to last indication) at the In#8
interface. */
#define TCM_REG_USEM_LENGTH_MIS 0x50170
+/* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_USEM_WEIGHT 0x500b8
/* [RW 21] Indirect access to the descriptor table of the XX protection
mechanism. The fields are: [5:0] - length of the message; 15:6] - message
pointer; 20:16] - next pointer. */
#define TCM_REG_XX_DESCR_TABLE 0x50280
+#define TCM_REG_XX_DESCR_TABLE_SIZE 32
/* [R 6] Use to read the value of XX protection Free counter. */
#define TCM_REG_XX_FREE 0x50178
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
The fields are:[4:0] - tail pointer; [10:5] - Link List size; 15:11] -
header pointer. */
#define TCM_REG_XX_TABLE 0x50240
-/* [RW 4] Load value for for cfc ac credit cnt. */
+/* [RW 4] Load value for cfc ac credit cnt. */
#define TM_REG_CFC_AC_CRDCNT_VAL 0x164208
/* [RW 4] Load value for cfc cld credit cnt. */
#define TM_REG_CFC_CLD_CRDCNT_VAL 0x164210
#define TM_REG_EN_CL1_INPUT 0x16400c
/* [RW 1] Enable client2 input. */
#define TM_REG_EN_CL2_INPUT 0x164010
+#define TM_REG_EN_LINEAR0_TIMER 0x164014
/* [RW 1] Enable real time counter. */
#define TM_REG_EN_REAL_TIME_CNT 0x1640d8
/* [RW 1] Enable for Timers state machines. */
/* [RW 4] Load value for expiration credit cnt. CFC max number of
outstanding load requests for timers (expiration) context loading. */
#define TM_REG_EXP_CRDCNT_VAL 0x164238
-/* [RW 18] Linear0 Max active cid. */
+/* [RW 32] Linear0 logic address. */
+#define TM_REG_LIN0_LOGIC_ADDR 0x164240
+/* [RW 18] Linear0 Max active cid (in banks of 32 entries). */
#define TM_REG_LIN0_MAX_ACTIVE_CID 0x164048
/* [WB 64] Linear0 phy address. */
#define TM_REG_LIN0_PHY_ADDR 0x164270
+/* [RW 1] Linear0 physical address valid. */
+#define TM_REG_LIN0_PHY_ADDR_VALID 0x164248
+#define TM_REG_LIN0_SCAN_ON 0x1640d0
/* [RW 24] Linear0 array scan timeout. */
#define TM_REG_LIN0_SCAN_TIME 0x16403c
+/* [RW 32] Linear1 logic address. */
+#define TM_REG_LIN1_LOGIC_ADDR 0x164250
/* [WB 64] Linear1 phy address. */
#define TM_REG_LIN1_PHY_ADDR 0x164280
+/* [RW 1] Linear1 physical address valid. */
+#define TM_REG_LIN1_PHY_ADDR_VALID 0x164258
/* [RW 6] Linear timer set_clear fifo threshold. */
#define TM_REG_LIN_SETCLR_FIFO_ALFULL_THR 0x164070
/* [RW 2] Load value for pci arbiter credit cnt. */
#define TM_REG_PCIARB_CRDCNT_VAL 0x164260
-/* [RW 1] Timer software reset - active high. */
-#define TM_REG_TIMER_SOFT_RST 0x164004
/* [RW 20] The amount of hardware cycles for each timer tick. */
#define TM_REG_TIMER_TICK_SIZE 0x16401c
/* [RW 8] Timers Context region. */
#define TM_REG_TM_INT_STS 0x1640f0
/* [RW 8] The event id for aggregated interrupt 0 */
#define TSDM_REG_AGG_INT_EVENT_0 0x42038
+#define TSDM_REG_AGG_INT_EVENT_1 0x4203c
+#define TSDM_REG_AGG_INT_EVENT_2 0x42040
+#define TSDM_REG_AGG_INT_EVENT_3 0x42044
+#define TSDM_REG_AGG_INT_EVENT_4 0x42048
+/* [RW 1] The T bit for aggregated interrupt 0 */
+#define TSDM_REG_AGG_INT_T_0 0x420b8
+#define TSDM_REG_AGG_INT_T_1 0x420bc
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define TSDM_REG_CFC_RSP_START_ADDR 0x42008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RW 32] Interrupt mask register #0 read/write */
#define TSDM_REG_TSDM_INT_MASK_0 0x4229c
#define TSDM_REG_TSDM_INT_MASK_1 0x422ac
+/* [R 32] Interrupt register #0 read */
+#define TSDM_REG_TSDM_INT_STS_0 0x42290
+#define TSDM_REG_TSDM_INT_STS_1 0x422a0
/* [RW 11] Parity mask register #0 read/write */
#define TSDM_REG_TSDM_PRTY_MASK 0x422bc
+/* [R 11] Parity register #0 read */
+#define TSDM_REG_TSDM_PRTY_STS 0x422b0
/* [RW 5] The number of time_slots in the arbitration cycle */
#define TSEM_REG_ARB_CYCLE_SIZE 0x180034
/* [RW 3] The source that is associated with arbitration element 0. Source
#define TSEM_REG_ENABLE_OUT 0x1800a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers the base address
- TSEM_REGISTERS_FAST_MEMORY (Offset: 0x1a0000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define TSEM_REG_FAST_MEMORY 0x1a0000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
/* [RW 32] Interrupt mask register #0 read/write */
#define TSEM_REG_TSEM_INT_MASK_0 0x180100
#define TSEM_REG_TSEM_INT_MASK_1 0x180110
+/* [R 32] Interrupt register #0 read */
+#define TSEM_REG_TSEM_INT_STS_0 0x1800f4
+#define TSEM_REG_TSEM_INT_STS_1 0x180104
/* [RW 32] Parity mask register #0 read/write */
#define TSEM_REG_TSEM_PRTY_MASK_0 0x180120
#define TSEM_REG_TSEM_PRTY_MASK_1 0x180130
+/* [R 32] Parity register #0 read */
+#define TSEM_REG_TSEM_PRTY_STS_0 0x180114
+#define TSEM_REG_TSEM_PRTY_STS_1 0x180124
/* [R 5] Used to read the XX protection CAM occupancy counter. */
#define UCM_REG_CAM_OCCUP 0xe0170
/* [RW 1] CDU AG read Interface enable. If 0 - the request input is
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the dorq interface is detected. */
#define UCM_REG_DORQ_LENGTH_MIS 0xe0168
+/* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_DORQ_WEIGHT 0xe00c0
/* [RW 8] The Event ID in case ErrorFlg input message bit is set. */
#define UCM_REG_ERR_EVNT_ID 0xe00a4
/* [RW 28] The CM erroneous header for QM and Timers formatting. */
connection type (one of 16). */
#define UCM_REG_N_SM_CTX_LD_0 0xe0054
#define UCM_REG_N_SM_CTX_LD_1 0xe0058
-#define UCM_REG_N_SM_CTX_LD_10 0xe007c
-#define UCM_REG_N_SM_CTX_LD_11 0xe0080
-#define UCM_REG_N_SM_CTX_LD_12 0xe0084
-#define UCM_REG_N_SM_CTX_LD_13 0xe0088
-#define UCM_REG_N_SM_CTX_LD_14 0xe008c
-#define UCM_REG_N_SM_CTX_LD_15 0xe0090
#define UCM_REG_N_SM_CTX_LD_2 0xe005c
#define UCM_REG_N_SM_CTX_LD_3 0xe0060
#define UCM_REG_N_SM_CTX_LD_4 0xe0064
-/* [RW 6] The physical queue number 0 per port index (CID[23]) */
+#define UCM_REG_N_SM_CTX_LD_5 0xe0068
#define UCM_REG_PHYS_QNUM0_0 0xe0110
#define UCM_REG_PHYS_QNUM0_1 0xe0114
-/* [RW 6] The physical queue number 1 per port index (CID[23]) */
#define UCM_REG_PHYS_QNUM1_0 0xe0118
#define UCM_REG_PHYS_QNUM1_1 0xe011c
+#define UCM_REG_PHYS_QNUM2_0 0xe0120
+#define UCM_REG_PHYS_QNUM2_1 0xe0124
+#define UCM_REG_PHYS_QNUM3_0 0xe0128
+#define UCM_REG_PHYS_QNUM3_1 0xe012c
/* [RW 8] The Event ID for Timers formatting in case of stop done. */
#define UCM_REG_STOP_EVNT_ID 0xe00ac
/* [RC 1] Set when the message length mismatch (relative to last indication)
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define UCM_REG_STORM_UCM_IFEN 0xe0010
+/* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_STORM_WEIGHT 0xe00b0
/* [RW 4] Timers output initial credit. Max credit available - 15.Write
writes the initial credit value; read returns the current value of the
credit counter. Must be initialized to 4 at start-up. */
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define UCM_REG_TM_UCM_IFEN 0xe001c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_TM_WEIGHT 0xe00d4
/* [RW 1] Input tsem Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define UCM_REG_UCM_INT_MASK 0xe01d4
/* [R 11] Interrupt register #0 read */
#define UCM_REG_UCM_INT_STS 0xe01c8
+/* [R 27] Parity register #0 read */
+#define UCM_REG_UCM_PRTY_STS 0xe01d8
/* [RW 2] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
stands for weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define UCM_REG_UQM_P_WEIGHT 0xe00cc
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_UQM_S_WEIGHT 0xe00d0
/* [RW 28] The CM header value for QM request (primary). */
#define UCM_REG_UQM_UCM_HDR_P 0xe0094
/* [RW 28] The CM header value for QM request (secondary). */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the SDM interface is detected. */
#define UCM_REG_USDM_LENGTH_MIS 0xe0158
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_USDM_WEIGHT 0xe00c8
/* [RW 1] Input xsem Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the xsem interface isdetected. */
#define UCM_REG_XSEM_LENGTH_MIS 0xe0164
+/* [RW 3] The weight of the input xsem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_XSEM_WEIGHT 0xe00bc
/* [RW 20] Indirect access to the descriptor table of the XX protection
mechanism. The fields are:[5:0] - message length; 14:6] - message
pointer; 19:15] - next pointer. */
#define UCM_REG_XX_DESCR_TABLE 0xe0280
+#define UCM_REG_XX_DESCR_TABLE_SIZE 32
/* [R 6] Use to read the XX protection Free counter. */
#define UCM_REG_XX_FREE 0xe016c
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
/* [RW 8] The event id for aggregated interrupt 0 */
#define USDM_REG_AGG_INT_EVENT_0 0xc4038
#define USDM_REG_AGG_INT_EVENT_1 0xc403c
-#define USDM_REG_AGG_INT_EVENT_10 0xc4060
-#define USDM_REG_AGG_INT_EVENT_11 0xc4064
-#define USDM_REG_AGG_INT_EVENT_12 0xc4068
-#define USDM_REG_AGG_INT_EVENT_13 0xc406c
-#define USDM_REG_AGG_INT_EVENT_14 0xc4070
-#define USDM_REG_AGG_INT_EVENT_15 0xc4074
-#define USDM_REG_AGG_INT_EVENT_16 0xc4078
-#define USDM_REG_AGG_INT_EVENT_17 0xc407c
-#define USDM_REG_AGG_INT_EVENT_18 0xc4080
-#define USDM_REG_AGG_INT_EVENT_19 0xc4084
+#define USDM_REG_AGG_INT_EVENT_2 0xc4040
+#define USDM_REG_AGG_INT_EVENT_4 0xc4048
+#define USDM_REG_AGG_INT_EVENT_5 0xc404c
+#define USDM_REG_AGG_INT_EVENT_6 0xc4050
/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
or auto-mask-mode (1) */
#define USDM_REG_AGG_INT_MODE_0 0xc41b8
#define USDM_REG_AGG_INT_MODE_1 0xc41bc
-#define USDM_REG_AGG_INT_MODE_10 0xc41e0
-#define USDM_REG_AGG_INT_MODE_11 0xc41e4
-#define USDM_REG_AGG_INT_MODE_12 0xc41e8
-#define USDM_REG_AGG_INT_MODE_13 0xc41ec
-#define USDM_REG_AGG_INT_MODE_14 0xc41f0
-#define USDM_REG_AGG_INT_MODE_15 0xc41f4
-#define USDM_REG_AGG_INT_MODE_16 0xc41f8
-#define USDM_REG_AGG_INT_MODE_17 0xc41fc
-#define USDM_REG_AGG_INT_MODE_18 0xc4200
-#define USDM_REG_AGG_INT_MODE_19 0xc4204
+#define USDM_REG_AGG_INT_MODE_4 0xc41c8
+#define USDM_REG_AGG_INT_MODE_5 0xc41cc
+#define USDM_REG_AGG_INT_MODE_6 0xc41d0
+/* [RW 1] The T bit for aggregated interrupt 5 */
+#define USDM_REG_AGG_INT_T_5 0xc40cc
+#define USDM_REG_AGG_INT_T_6 0xc40d0
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define USDM_REG_CFC_RSP_START_ADDR 0xc4008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RW 32] Interrupt mask register #0 read/write */
#define USDM_REG_USDM_INT_MASK_0 0xc42a0
#define USDM_REG_USDM_INT_MASK_1 0xc42b0
+/* [R 32] Interrupt register #0 read */
+#define USDM_REG_USDM_INT_STS_0 0xc4294
+#define USDM_REG_USDM_INT_STS_1 0xc42a4
/* [RW 11] Parity mask register #0 read/write */
#define USDM_REG_USDM_PRTY_MASK 0xc42c0
+/* [R 11] Parity register #0 read */
+#define USDM_REG_USDM_PRTY_STS 0xc42b4
/* [RW 5] The number of time_slots in the arbitration cycle */
#define USEM_REG_ARB_CYCLE_SIZE 0x300034
/* [RW 3] The source that is associated with arbitration element 0. Source
#define USEM_REG_ENABLE_OUT 0x3000a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers... the base address
- USEM_REGISTERS_FAST_MEMORY (Offset: 0x320000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define USEM_REG_FAST_MEMORY 0x320000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
/* [RW 32] Interrupt mask register #0 read/write */
#define USEM_REG_USEM_INT_MASK_0 0x300110
#define USEM_REG_USEM_INT_MASK_1 0x300120
+/* [R 32] Interrupt register #0 read */
+#define USEM_REG_USEM_INT_STS_0 0x300104
+#define USEM_REG_USEM_INT_STS_1 0x300114
/* [RW 32] Parity mask register #0 read/write */
#define USEM_REG_USEM_PRTY_MASK_0 0x300130
#define USEM_REG_USEM_PRTY_MASK_1 0x300140
+/* [R 32] Parity register #0 read */
+#define USEM_REG_USEM_PRTY_STS_0 0x300124
+#define USEM_REG_USEM_PRTY_STS_1 0x300134
/* [RW 2] The queue index for registration on Aux1 counter flag. */
#define XCM_REG_AUX1_Q 0x20134
/* [RW 2] Per each decision rule the queue index to register to. */
/* [RC 1] Set at message length mismatch (relative to last indication) at
the dorq interface. */
#define XCM_REG_DORQ_LENGTH_MIS 0x20230
+/* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_DORQ_WEIGHT 0x200cc
/* [RW 8] The Event ID in case the ErrorFlg input message bit is set. */
#define XCM_REG_ERR_EVNT_ID 0x200b0
/* [RW 28] The CM erroneous header for QM and Timers formatting. */
writes the initial credit value; read returns the current value of the
credit counter. Must be initialized to 64 at start-up. */
#define XCM_REG_FIC1_INIT_CRD 0x20410
-/* [RW 8] The maximum delayed ACK counter value.Must be at least 2. Per port
- value. */
#define XCM_REG_GLB_DEL_ACK_MAX_CNT_0 0x20118
#define XCM_REG_GLB_DEL_ACK_MAX_CNT_1 0x2011c
-/* [RW 28] The delayed ACK timeout in ticks. Per port value. */
#define XCM_REG_GLB_DEL_ACK_TMR_VAL_0 0x20108
#define XCM_REG_GLB_DEL_ACK_TMR_VAL_1 0x2010c
/* [RW 1] Arbitratiojn between Input Arbiter groups: 0 - fair Round-Robin; 1
/* [RC 1] Set at message length mismatch (relative to last indication) at
the nig0 interface. */
#define XCM_REG_NIG0_LENGTH_MIS 0x20238
+/* [RW 3] The weight of the input nig0 in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_NIG0_WEIGHT 0x200d4
/* [RW 1] Input nig1 Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
/* [RC 1] Set at message length mismatch (relative to last indication) at
the nig1 interface. */
#define XCM_REG_NIG1_LENGTH_MIS 0x2023c
-/* [RW 3] The weight of the input nig1 in the WRR mechanism. 0 stands for
- weight 8 (the most prioritised); 1 stands for weight 1(least
- prioritised); 2 stands for weight 2; tc. */
-#define XCM_REG_NIG1_WEIGHT 0x200d8
/* [RW 5] The number of double REG-pairs; loaded from the STORM context and
sent to STORM; for a specific connection type. The double REG-pairs are
used in order to align to STORM context row size of 128 bits. The offset
connection type (one of 16). */
#define XCM_REG_N_SM_CTX_LD_0 0x20060
#define XCM_REG_N_SM_CTX_LD_1 0x20064
-#define XCM_REG_N_SM_CTX_LD_10 0x20088
-#define XCM_REG_N_SM_CTX_LD_11 0x2008c
-#define XCM_REG_N_SM_CTX_LD_12 0x20090
-#define XCM_REG_N_SM_CTX_LD_13 0x20094
-#define XCM_REG_N_SM_CTX_LD_14 0x20098
-#define XCM_REG_N_SM_CTX_LD_15 0x2009c
#define XCM_REG_N_SM_CTX_LD_2 0x20068
#define XCM_REG_N_SM_CTX_LD_3 0x2006c
#define XCM_REG_N_SM_CTX_LD_4 0x20070
+#define XCM_REG_N_SM_CTX_LD_5 0x20074
/* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define XCM_REG_PBF_WEIGHT 0x200d0
+#define XCM_REG_PHYS_QNUM3_0 0x20100
+#define XCM_REG_PHYS_QNUM3_1 0x20104
/* [RW 8] The Event ID for Timers formatting in case of stop done. */
#define XCM_REG_STOP_EVNT_ID 0x200b8
/* [RC 1] Set at message length mismatch (relative to last indication) at
writes the initial credit value; read returns the current value of the
credit counter. Must be initialized to 4 at start-up. */
#define XCM_REG_TM_INIT_CRD 0x2041c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_TM_WEIGHT 0x200ec
/* [RW 28] The CM header for Timers expiration command. */
#define XCM_REG_TM_XCM_HDR 0x200a8
/* [RW 1] Timers - CM Interface enable. If 0 - the valid input is
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define XCM_REG_USEM_WEIGHT 0x200c8
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD00 0x201d4
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD01 0x201d8
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD10 0x201dc
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD11 0x201e0
-/* [RW 8] DA counter update value used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL00 0x201e4
-/* [RW 8] DA counter update value; used in case of window update
- doorbell.The first index stands for the value DaEnable of that
- connection. The second index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL01 0x201e8
-/* [RW 8] DA counter update value; used in case of window update
- doorbell.The first index stands for the value DaEnable of that
- connection. The second index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL10 0x201ec
-/* [RW 8] DA counter update value; used in case of window update
- doorbell.The first index stands for the value DaEnable of that
- connection. The second index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL11 0x201f0
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00 0x201c4
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01 0x201c8
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10 0x201cc
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11 0x201d0
/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
#define XCM_REG_XCM_INT_MASK 0x202b4
/* [R 14] Interrupt register #0 read */
#define XCM_REG_XCM_INT_STS 0x202a8
+/* [R 30] Parity register #0 read */
+#define XCM_REG_XCM_PRTY_STS 0x202b8
/* [RW 4] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
stands for weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define XCM_REG_XQM_P_WEIGHT 0x200e4
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_XQM_S_WEIGHT 0x200e8
/* [RW 28] The CM header value for QM request (primary). */
#define XCM_REG_XQM_XCM_HDR_P 0x200a0
/* [RW 28] The CM header value for QM request (secondary). */
mechanism. The fields are: [5:0] - message length; 11:6] - message
pointer; 16:12] - next pointer. */
#define XCM_REG_XX_DESCR_TABLE 0x20480
+#define XCM_REG_XX_DESCR_TABLE_SIZE 32
/* [R 6] Used to read the XX protection Free counter. */
#define XCM_REG_XX_FREE 0x20240
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
#define XCM_REG_XX_MSG_NUM 0x20428
/* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */
#define XCM_REG_XX_OVFL_EVNT_ID 0x20058
-/* [RW 15] Indirect access to the XX table of the XX protection mechanism.
+/* [RW 16] Indirect access to the XX table of the XX protection mechanism.
The fields are:[4:0] - tail pointer; 9:5] - Link List size; 14:10] -
header pointer. */
#define XCM_REG_XX_TABLE 0x20500
#define XSDM_REG_AGG_INT_EVENT_12 0x166068
#define XSDM_REG_AGG_INT_EVENT_13 0x16606c
#define XSDM_REG_AGG_INT_EVENT_14 0x166070
-#define XSDM_REG_AGG_INT_EVENT_15 0x166074
-#define XSDM_REG_AGG_INT_EVENT_16 0x166078
-#define XSDM_REG_AGG_INT_EVENT_17 0x16607c
-#define XSDM_REG_AGG_INT_EVENT_18 0x166080
-#define XSDM_REG_AGG_INT_EVENT_19 0x166084
#define XSDM_REG_AGG_INT_EVENT_2 0x166040
-#define XSDM_REG_AGG_INT_EVENT_20 0x166088
-#define XSDM_REG_AGG_INT_EVENT_21 0x16608c
-#define XSDM_REG_AGG_INT_EVENT_22 0x166090
-#define XSDM_REG_AGG_INT_EVENT_23 0x166094
-#define XSDM_REG_AGG_INT_EVENT_24 0x166098
-#define XSDM_REG_AGG_INT_EVENT_25 0x16609c
-#define XSDM_REG_AGG_INT_EVENT_26 0x1660a0
-#define XSDM_REG_AGG_INT_EVENT_27 0x1660a4
-#define XSDM_REG_AGG_INT_EVENT_28 0x1660a8
-#define XSDM_REG_AGG_INT_EVENT_29 0x1660ac
+#define XSDM_REG_AGG_INT_EVENT_3 0x166044
+#define XSDM_REG_AGG_INT_EVENT_4 0x166048
+#define XSDM_REG_AGG_INT_EVENT_5 0x16604c
+#define XSDM_REG_AGG_INT_EVENT_6 0x166050
+#define XSDM_REG_AGG_INT_EVENT_7 0x166054
+#define XSDM_REG_AGG_INT_EVENT_8 0x166058
+#define XSDM_REG_AGG_INT_EVENT_9 0x16605c
/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
or auto-mask-mode (1) */
#define XSDM_REG_AGG_INT_MODE_0 0x1661b8
#define XSDM_REG_AGG_INT_MODE_1 0x1661bc
-#define XSDM_REG_AGG_INT_MODE_10 0x1661e0
-#define XSDM_REG_AGG_INT_MODE_11 0x1661e4
-#define XSDM_REG_AGG_INT_MODE_12 0x1661e8
-#define XSDM_REG_AGG_INT_MODE_13 0x1661ec
-#define XSDM_REG_AGG_INT_MODE_14 0x1661f0
-#define XSDM_REG_AGG_INT_MODE_15 0x1661f4
-#define XSDM_REG_AGG_INT_MODE_16 0x1661f8
-#define XSDM_REG_AGG_INT_MODE_17 0x1661fc
-#define XSDM_REG_AGG_INT_MODE_18 0x166200
-#define XSDM_REG_AGG_INT_MODE_19 0x166204
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define XSDM_REG_CFC_RSP_START_ADDR 0x166008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RW 32] Interrupt mask register #0 read/write */
#define XSDM_REG_XSDM_INT_MASK_0 0x16629c
#define XSDM_REG_XSDM_INT_MASK_1 0x1662ac
+/* [R 32] Interrupt register #0 read */
+#define XSDM_REG_XSDM_INT_STS_0 0x166290
+#define XSDM_REG_XSDM_INT_STS_1 0x1662a0
/* [RW 11] Parity mask register #0 read/write */
#define XSDM_REG_XSDM_PRTY_MASK 0x1662bc
+/* [R 11] Parity register #0 read */
+#define XSDM_REG_XSDM_PRTY_STS 0x1662b0
/* [RW 5] The number of time_slots in the arbitration cycle */
#define XSEM_REG_ARB_CYCLE_SIZE 0x280034
/* [RW 3] The source that is associated with arbitration element 0. Source
#define XSEM_REG_ENABLE_OUT 0x2800a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers the base address
- XSEM_REGISTERS_FAST_MEMORY (Offset: 0x2a0000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define XSEM_REG_FAST_MEMORY 0x2a0000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
/* [RW 32] Interrupt mask register #0 read/write */
#define XSEM_REG_XSEM_INT_MASK_0 0x280110
#define XSEM_REG_XSEM_INT_MASK_1 0x280120
+/* [R 32] Interrupt register #0 read */
+#define XSEM_REG_XSEM_INT_STS_0 0x280104
+#define XSEM_REG_XSEM_INT_STS_1 0x280114
/* [RW 32] Parity mask register #0 read/write */
#define XSEM_REG_XSEM_PRTY_MASK_0 0x280130
#define XSEM_REG_XSEM_PRTY_MASK_1 0x280140
+/* [R 32] Parity register #0 read */
+#define XSEM_REG_XSEM_PRTY_STS_0 0x280124
+#define XSEM_REG_XSEM_PRTY_STS_1 0x280134
#define MCPR_NVM_ACCESS_ENABLE_EN (1L<<0)
#define MCPR_NVM_ACCESS_ENABLE_WR_EN (1L<<1)
#define MCPR_NVM_ADDR_NVM_ADDR_VALUE (0xffffffL<<0)
#define MCPR_NVM_COMMAND_FIRST (1L<<7)
#define MCPR_NVM_COMMAND_LAST (1L<<8)
#define MCPR_NVM_COMMAND_WR (1L<<5)
-#define MCPR_NVM_COMMAND_WREN (1L<<16)
-#define MCPR_NVM_COMMAND_WREN_BITSHIFT 16
-#define MCPR_NVM_COMMAND_WRDI (1L<<17)
-#define MCPR_NVM_COMMAND_WRDI_BITSHIFT 17
#define MCPR_NVM_SW_ARB_ARB_ARB1 (1L<<9)
#define MCPR_NVM_SW_ARB_ARB_REQ_CLR1 (1L<<5)
#define MCPR_NVM_SW_ARB_ARB_REQ_SET1 (1L<<1)
#define BIGMAC_REGISTER_TX_SOURCE_ADDR (0x08<<3)
#define BIGMAC_REGISTER_TX_STAT_GTBYT (0x20<<3)
#define BIGMAC_REGISTER_TX_STAT_GTPKT (0x0C<<3)
+#define EMAC_LED_1000MB_OVERRIDE (1L<<1)
+#define EMAC_LED_100MB_OVERRIDE (1L<<2)
+#define EMAC_LED_10MB_OVERRIDE (1L<<3)
+#define EMAC_LED_2500MB_OVERRIDE (1L<<12)
+#define EMAC_LED_OVERRIDE (1L<<0)
+#define EMAC_LED_TRAFFIC (1L<<6)
#define EMAC_MDIO_COMM_COMMAND_ADDRESS (0L<<26)
-#define EMAC_MDIO_COMM_COMMAND_READ_22 (2L<<26)
#define EMAC_MDIO_COMM_COMMAND_READ_45 (3L<<26)
-#define EMAC_MDIO_COMM_COMMAND_WRITE_22 (1L<<26)
#define EMAC_MDIO_COMM_COMMAND_WRITE_45 (1L<<26)
#define EMAC_MDIO_COMM_DATA (0xffffL<<0)
#define EMAC_MDIO_COMM_START_BUSY (1L<<29)
#define EMAC_MDIO_MODE_AUTO_POLL (1L<<4)
#define EMAC_MDIO_MODE_CLAUSE_45 (1L<<31)
+#define EMAC_MDIO_MODE_CLOCK_CNT (0x3fL<<16)
+#define EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT 16
#define EMAC_MODE_25G_MODE (1L<<5)
-#define EMAC_MODE_ACPI_RCVD (1L<<20)
#define EMAC_MODE_HALF_DUPLEX (1L<<1)
-#define EMAC_MODE_MPKT (1L<<18)
-#define EMAC_MODE_MPKT_RCVD (1L<<19)
#define EMAC_MODE_PORT_GMII (2L<<2)
#define EMAC_MODE_PORT_MII (1L<<2)
#define EMAC_MODE_PORT_MII_10M (3L<<2)
#define EMAC_MODE_RESET (1L<<0)
+#define EMAC_REG_EMAC_LED 0xc
#define EMAC_REG_EMAC_MAC_MATCH 0x10
#define EMAC_REG_EMAC_MDIO_COMM 0xac
#define EMAC_REG_EMAC_MDIO_MODE 0xb4
#define EMAC_RX_MODE_FLOW_EN (1L<<2)
#define EMAC_RX_MODE_KEEP_VLAN_TAG (1L<<10)
#define EMAC_RX_MODE_PROMISCUOUS (1L<<8)
+#define EMAC_RX_MODE_RESET (1L<<0)
#define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31)
#define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3)
+#define EMAC_TX_MODE_FLOW_EN (1L<<4)
#define EMAC_TX_MODE_RESET (1L<<0)
+#define MISC_REGISTERS_GPIO_0 0
+#define MISC_REGISTERS_GPIO_1 1
+#define MISC_REGISTERS_GPIO_2 2
+#define MISC_REGISTERS_GPIO_3 3
+#define MISC_REGISTERS_GPIO_CLR_POS 16
+#define MISC_REGISTERS_GPIO_FLOAT (0xffL<<24)
+#define MISC_REGISTERS_GPIO_FLOAT_POS 24
+#define MISC_REGISTERS_GPIO_HIGH 1
+#define MISC_REGISTERS_GPIO_INPUT_HI_Z 2
+#define MISC_REGISTERS_GPIO_INT_CLR_POS 24
+#define MISC_REGISTERS_GPIO_INT_OUTPUT_CLR 0
+#define MISC_REGISTERS_GPIO_INT_OUTPUT_SET 1
+#define MISC_REGISTERS_GPIO_INT_SET_POS 16
+#define MISC_REGISTERS_GPIO_LOW 0
+#define MISC_REGISTERS_GPIO_OUTPUT_HIGH 1
+#define MISC_REGISTERS_GPIO_OUTPUT_LOW 0
+#define MISC_REGISTERS_GPIO_PORT_SHIFT 4
+#define MISC_REGISTERS_GPIO_SET_POS 8
#define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588
+#define MISC_REGISTERS_RESET_REG_1_RST_NIG (0x1<<7)
#define MISC_REGISTERS_RESET_REG_1_SET 0x584
#define MISC_REGISTERS_RESET_REG_2_CLEAR 0x598
#define MISC_REGISTERS_RESET_REG_2_RST_BMAC0 (0x1<<0)
#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW (0x1<<4)
#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB (0x1<<8)
#define MISC_REGISTERS_RESET_REG_3_SET 0x5a4
+#define MISC_REGISTERS_SPIO_4 4
+#define MISC_REGISTERS_SPIO_5 5
+#define MISC_REGISTERS_SPIO_7 7
+#define MISC_REGISTERS_SPIO_CLR_POS 16
+#define MISC_REGISTERS_SPIO_FLOAT (0xffL<<24)
+#define MISC_REGISTERS_SPIO_FLOAT_POS 24
+#define MISC_REGISTERS_SPIO_INPUT_HI_Z 2
+#define MISC_REGISTERS_SPIO_INT_OLD_SET_POS 16
+#define MISC_REGISTERS_SPIO_OUTPUT_HIGH 1
+#define MISC_REGISTERS_SPIO_OUTPUT_LOW 0
+#define MISC_REGISTERS_SPIO_SET_POS 8
+#define HW_LOCK_MAX_RESOURCE_VALUE 31
+#define HW_LOCK_RESOURCE_GPIO 1
+#define HW_LOCK_RESOURCE_MDIO 0
+#define HW_LOCK_RESOURCE_PORT0_ATT_MASK 3
+#define HW_LOCK_RESOURCE_SPIO 2
+#define HW_LOCK_RESOURCE_UNDI 5
+#define PRS_FLAG_OVERETH_IPV4 1
#define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (1<<18)
#define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (1<<31)
#define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (1<<9)
#define AEU_INPUTS_ATTN_BITS_DMAE_HW_INTERRUPT (1<<11)
#define AEU_INPUTS_ATTN_BITS_DOORBELLQ_HW_INTERRUPT (1<<13)
#define AEU_INPUTS_ATTN_BITS_DOORBELLQ_PARITY_ERROR (1<<12)
+#define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 (1<<5)
+#define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1 (1<<9)
#define AEU_INPUTS_ATTN_BITS_IGU_PARITY_ERROR (1<<12)
#define AEU_INPUTS_ATTN_BITS_MISC_HW_INTERRUPT (1<<15)
#define AEU_INPUTS_ATTN_BITS_MISC_PARITY_ERROR (1<<14)
#define AEU_INPUTS_ATTN_BITS_QM_HW_INTERRUPT (1<<3)
#define AEU_INPUTS_ATTN_BITS_QM_PARITY_ERROR (1<<2)
#define AEU_INPUTS_ATTN_BITS_SEARCHER_PARITY_ERROR (1<<22)
+#define AEU_INPUTS_ATTN_BITS_SPIO5 (1<<15)
#define AEU_INPUTS_ATTN_BITS_TCM_HW_INTERRUPT (1<<27)
#define AEU_INPUTS_ATTN_BITS_TIMERS_HW_INTERRUPT (1<<5)
#define AEU_INPUTS_ATTN_BITS_TSDM_HW_INTERRUPT (1<<25)
#define AEU_INPUTS_ATTN_BITS_XSEMI_PARITY_ERROR (1<<10)
#define RESERVED_GENERAL_ATTENTION_BIT_0 0
-#define EVEREST_GEN_ATTN_IN_USE_MASK 0x3e0
+#define EVEREST_GEN_ATTN_IN_USE_MASK 0x3ffe0
#define EVEREST_LATCHED_ATTN_IN_USE_MASK 0xffe00000
#define RESERVED_GENERAL_ATTENTION_BIT_6 6
/* mcp error attention bit */
#define MCP_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_11
+/*E1H NIG status sync attention mapped to group 4-7*/
+#define LINK_SYNC_ATTENTION_BIT_FUNC_0 RESERVED_GENERAL_ATTENTION_BIT_12
+#define LINK_SYNC_ATTENTION_BIT_FUNC_1 RESERVED_GENERAL_ATTENTION_BIT_13
+#define LINK_SYNC_ATTENTION_BIT_FUNC_2 RESERVED_GENERAL_ATTENTION_BIT_14
+#define LINK_SYNC_ATTENTION_BIT_FUNC_3 RESERVED_GENERAL_ATTENTION_BIT_15
+#define LINK_SYNC_ATTENTION_BIT_FUNC_4 RESERVED_GENERAL_ATTENTION_BIT_16
+#define LINK_SYNC_ATTENTION_BIT_FUNC_5 RESERVED_GENERAL_ATTENTION_BIT_17
+#define LINK_SYNC_ATTENTION_BIT_FUNC_6 RESERVED_GENERAL_ATTENTION_BIT_18
+#define LINK_SYNC_ATTENTION_BIT_FUNC_7 RESERVED_GENERAL_ATTENTION_BIT_19
+
+
#define LATCHED_ATTN_RBCR 23
#define LATCHED_ATTN_RBCT 24
#define LATCHED_ATTN_RBCN 25
#define LATCHED_ATTN_SCPAD_PARITY_MCP 33
#define GENERAL_ATTEN_WORD(atten_name) ((94 + atten_name) / 32)
-#define GENERAL_ATTEN_OFFSET(atten_name) (1 << ((94 + atten_name) % 32))
+#define GENERAL_ATTEN_OFFSET(atten_name)\
+ (1UL << ((94 + atten_name) % 32))
/*
* This file defines GRC base address for every block.
* This file is included by chipsim, asm microcode and cpp microcode.
#define GRCBASE_MISC_AEU GRCBASE_MISC
-/*the offset of the configuration space in the pci core register*/
+/* offset of configuration space in the pci core register */
#define PCICFG_OFFSET 0x2000
#define PCICFG_VENDOR_ID_OFFSET 0x00
#define PCICFG_DEVICE_ID_OFFSET 0x02
-#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c
-#define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e
-#define PCICFG_INT_LINE 0x3c
-#define PCICFG_INT_PIN 0x3d
+#define PCICFG_COMMAND_OFFSET 0x04
+#define PCICFG_COMMAND_IO_SPACE (1<<0)
+#define PCICFG_COMMAND_MEM_SPACE (1<<1)
+#define PCICFG_COMMAND_BUS_MASTER (1<<2)
+#define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3)
+#define PCICFG_COMMAND_MWI_CYCLES (1<<4)
+#define PCICFG_COMMAND_VGA_SNOOP (1<<5)
+#define PCICFG_COMMAND_PERR_ENA (1<<6)
+#define PCICFG_COMMAND_STEPPING (1<<7)
+#define PCICFG_COMMAND_SERR_ENA (1<<8)
+#define PCICFG_COMMAND_FAST_B2B (1<<9)
+#define PCICFG_COMMAND_INT_DISABLE (1<<10)
+#define PCICFG_COMMAND_RESERVED (0x1f<<11)
+#define PCICFG_STATUS_OFFSET 0x06
+#define PCICFG_REVESION_ID_OFFSET 0x08
#define PCICFG_CACHE_LINE_SIZE 0x0c
#define PCICFG_LATENCY_TIMER 0x0d
-#define PCICFG_REVESION_ID 0x08
#define PCICFG_BAR_1_LOW 0x10
#define PCICFG_BAR_1_HIGH 0x14
#define PCICFG_BAR_2_LOW 0x18
#define PCICFG_BAR_2_HIGH 0x1c
+#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c
+#define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e
+#define PCICFG_INT_LINE 0x3c
+#define PCICFG_INT_PIN 0x3d
+#define PCICFG_PM_CAPABILITY 0x48
+#define PCICFG_PM_CAPABILITY_VERSION (0x3<<16)
+#define PCICFG_PM_CAPABILITY_CLOCK (1<<19)
+#define PCICFG_PM_CAPABILITY_RESERVED (1<<20)
+#define PCICFG_PM_CAPABILITY_DSI (1<<21)
+#define PCICFG_PM_CAPABILITY_AUX_CURRENT (0x7<<22)
+#define PCICFG_PM_CAPABILITY_D1_SUPPORT (1<<25)
+#define PCICFG_PM_CAPABILITY_D2_SUPPORT (1<<26)
+#define PCICFG_PM_CAPABILITY_PME_IN_D0 (1<<27)
+#define PCICFG_PM_CAPABILITY_PME_IN_D1 (1<<28)
+#define PCICFG_PM_CAPABILITY_PME_IN_D2 (1<<29)
+#define PCICFG_PM_CAPABILITY_PME_IN_D3_HOT (1<<30)
+#define PCICFG_PM_CAPABILITY_PME_IN_D3_COLD (1<<31)
+#define PCICFG_PM_CSR_OFFSET 0x4c
+#define PCICFG_PM_CSR_STATE (0x3<<0)
+#define PCICFG_PM_CSR_PME_ENABLE (1<<8)
+#define PCICFG_PM_CSR_PME_STATUS (1<<15)
+#define PCICFG_MSI_CAP_ID_OFFSET 0x58
+#define PCICFG_MSI_CONTROL_ENABLE (0x1<<16)
+#define PCICFG_MSI_CONTROL_MCAP (0x7<<17)
+#define PCICFG_MSI_CONTROL_MENA (0x7<<20)
+#define PCICFG_MSI_CONTROL_64_BIT_ADDR_CAP (0x1<<23)
+#define PCICFG_MSI_CONTROL_MSI_PVMASK_CAPABLE (0x1<<24)
#define PCICFG_GRC_ADDRESS 0x78
#define PCICFG_GRC_DATA 0x80
+#define PCICFG_MSIX_CAP_ID_OFFSET 0xa0
+#define PCICFG_MSIX_CONTROL_TABLE_SIZE (0x7ff<<16)
+#define PCICFG_MSIX_CONTROL_RESERVED (0x7<<27)
+#define PCICFG_MSIX_CONTROL_FUNC_MASK (0x1<<30)
+#define PCICFG_MSIX_CONTROL_MSIX_ENABLE (0x1<<31)
+
#define PCICFG_DEVICE_CONTROL 0xb4
+#define PCICFG_DEVICE_STATUS 0xb6
+#define PCICFG_DEVICE_STATUS_CORR_ERR_DET (1<<0)
+#define PCICFG_DEVICE_STATUS_NON_FATAL_ERR_DET (1<<1)
+#define PCICFG_DEVICE_STATUS_FATAL_ERR_DET (1<<2)
+#define PCICFG_DEVICE_STATUS_UNSUP_REQ_DET (1<<3)
+#define PCICFG_DEVICE_STATUS_AUX_PWR_DET (1<<4)
+#define PCICFG_DEVICE_STATUS_NO_PEND (1<<5)
#define PCICFG_LINK_CONTROL 0xbc
+
#define BAR_USTRORM_INTMEM 0x400000
#define BAR_CSTRORM_INTMEM 0x410000
#define BAR_XSTRORM_INTMEM 0x420000
#define BAR_TSTRORM_INTMEM 0x430000
+/* for accessing the IGU in case of status block ACK */
#define BAR_IGU_INTMEM 0x440000
#define BAR_DOORBELL_OFFSET 0x800000
#define BAR_ME_REGISTER 0x450000
-
-#define GRC_CONFIG_2_SIZE_REG 0x408 /* config_2 offset */
-#define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0)
+/* config_2 offset */
+#define GRC_CONFIG_2_SIZE_REG 0x408
+#define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0)
#define PCI_CONFIG_2_BAR1_SIZE_DISABLED (0L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_64K (1L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_128K (2L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_256M (13L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_512M (14L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_1G (15L<<0)
-#define PCI_CONFIG_2_BAR1_64ENA (1L<<4)
-#define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5)
-#define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6)
-#define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7)
-#define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8)
+#define PCI_CONFIG_2_BAR1_64ENA (1L<<4)
+#define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5)
+#define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6)
+#define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7)
+#define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_DISABLED (0L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_2K (1L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_4K (2L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_8M (13L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_16M (14L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_32M (15L<<8)
-#define PCI_CONFIG_2_BAR_PREFETCH (1L<<16)
-#define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17)
+#define PCI_CONFIG_2_BAR_PREFETCH (1L<<16)
+#define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17)
/* config_3 offset */
-#define GRC_CONFIG_3_SIZE_REG (0x40c)
-#define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0)
-#define PCI_CONFIG_3_FORCE_PME (1L<<24)
-#define PCI_CONFIG_3_PME_STATUS (1L<<25)
-#define PCI_CONFIG_3_PME_ENABLE (1L<<26)
-#define PCI_CONFIG_3_PM_STATE (0x3L<<27)
-#define PCI_CONFIG_3_VAUX_PRESET (1L<<30)
-#define PCI_CONFIG_3_PCI_POWER (1L<<31)
-
-/* config_2 offset */
-#define GRC_CONFIG_2_SIZE_REG 0x408
+#define GRC_CONFIG_3_SIZE_REG 0x40c
+#define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0)
+#define PCI_CONFIG_3_FORCE_PME (1L<<24)
+#define PCI_CONFIG_3_PME_STATUS (1L<<25)
+#define PCI_CONFIG_3_PME_ENABLE (1L<<26)
+#define PCI_CONFIG_3_PM_STATE (0x3L<<27)
+#define PCI_CONFIG_3_VAUX_PRESET (1L<<30)
+#define PCI_CONFIG_3_PCI_POWER (1L<<31)
#define GRC_BAR2_CONFIG 0x4e0
-#define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0)
-#define PCI_CONFIG_2_BAR2_64ENA (1L<<4)
+#define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0)
+#define PCI_CONFIG_2_BAR2_64ENA (1L<<4)
+
+#define PCI_PM_DATA_A 0x410
+#define PCI_PM_DATA_B 0x414
+#define PCI_ID_VAL1 0x434
+#define PCI_ID_VAL2 0x438
-#define PCI_PM_DATA_A (0x410)
-#define PCI_PM_DATA_B (0x414)
-#define PCI_ID_VAL1 (0x434)
-#define PCI_ID_VAL2 (0x438)
-#define MDIO_REG_BANK_CL73_IEEEB0 0x0
-#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL 0x0
+#define MDIO_REG_BANK_CL73_IEEEB0 0x0
+#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL 0x0
#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN 0x0200
#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN 0x1000
#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_MAIN_RST 0x8000
-#define MDIO_REG_BANK_CL73_IEEEB1 0x10
-#define MDIO_CL73_IEEEB1_AN_ADV2 0x01
+#define MDIO_REG_BANK_CL73_IEEEB1 0x10
+#define MDIO_CL73_IEEEB1_AN_ADV1 0x00
+#define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE 0x0400
+#define MDIO_CL73_IEEEB1_AN_ADV1_ASYMMETRIC 0x0800
+#define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH 0x0C00
+#define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK 0x0C00
+#define MDIO_CL73_IEEEB1_AN_ADV2 0x01
#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M 0x0000
#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX 0x0020
#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4 0x0040
#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KR 0x0080
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1 0x03
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE 0x0400
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_ASYMMETRIC 0x0800
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_BOTH 0x0C00
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK 0x0C00
#define MDIO_REG_BANK_RX0 0x80b0
+#define MDIO_RX0_RX_STATUS 0x10
+#define MDIO_RX0_RX_STATUS_SIGDET 0x8000
+#define MDIO_RX0_RX_STATUS_RX_SEQ_DONE 0x1000
#define MDIO_RX0_RX_EQ_BOOST 0x1c
#define MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
#define MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL 0x10
#define MDIO_REG_BANK_RX_ALL 0x80f0
#define MDIO_RX_ALL_RX_EQ_BOOST 0x1c
#define MDIO_RX_ALL_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
-#define MDIO_RX_ALL_RX_EQ_BOOST_OFFSET_CTRL 0x10
+#define MDIO_RX_ALL_RX_EQ_BOOST_OFFSET_CTRL 0x10
#define MDIO_REG_BANK_TX0 0x8060
#define MDIO_TX0_TX_DRIVER 0x17
#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+#define MDIO_REG_BANK_TX1 0x8070
+#define MDIO_TX1_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_TX2 0x8080
+#define MDIO_TX2_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_TX3 0x8090
+#define MDIO_TX3_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
#define MDIO_REG_BANK_XGXS_BLOCK0 0x8000
#define MDIO_BLOCK0_XGXS_CONTROL 0x10
#define MDIO_XGXS_BLOCK2_RX_LN_SWAP 0x10
#define MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE 0x8000
#define MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE 0x4000
-#define MDIO_XGXS_BLOCK2_TX_LN_SWAP 0x11
+#define MDIO_XGXS_BLOCK2_TX_LN_SWAP 0x11
#define MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE 0x8000
-#define MDIO_XGXS_BLOCK2_TEST_MODE_LANE 0x15
+#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G 0x14
+#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS 0x0001
+#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS 0x0010
+#define MDIO_XGXS_BLOCK2_TEST_MODE_LANE 0x15
#define MDIO_REG_BANK_GP_STATUS 0x8120
-#define MDIO_GP_STATUS_TOP_AN_STATUS1 0x1B
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE 0x0001
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE 0x0002
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS 0x0004
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS 0x0008
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE 0x0010
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_LP_NP_BAM_ABLE 0x0020
-
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE 0x0040
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE 0x0080
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK 0x3f00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M 0x0000
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M 0x0100
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G 0x0200
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G 0x0300
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G 0x0400
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G 0x0500
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG 0x0600
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 0x0700
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG 0x0800
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G 0x0900
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G 0x0A00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G 0x0B00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G 0x0C00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX 0x0D00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 0x0E00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1 0x1B
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE 0x0001
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE 0x0002
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS 0x0004
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS 0x0008
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE 0x0010
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_LP_NP_BAM_ABLE 0x0020
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE 0x0040
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE 0x0080
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK 0x3f00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M 0x0000
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M 0x0100
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G 0x0200
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G 0x0300
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G 0x0400
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G 0x0500
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG 0x0600
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 0x0700
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG 0x0800
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G 0x0900
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G 0x0A00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G 0x0B00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G 0x0C00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX 0x0D00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 0x0E00
#define MDIO_REG_BANK_10G_PARALLEL_DETECT 0x8130
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL 0x11
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN 0x1
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK 0x13
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT (0xb71<<1)
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS 0x10
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK 0x8000
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL 0x11
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN 0x1
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK 0x13
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT (0xb71<<1)
#define MDIO_REG_BANK_SERDES_DIGITAL 0x8300
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1 0x10
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE 0x0001
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_TBI_IF 0x0002
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN 0x0004
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT 0x0008
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET 0x0010
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE 0x0020
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2 0x11
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN 0x0001
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_AN_FST_TMR 0x0040
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1 0x14
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_DUPLEX 0x0004
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_MASK 0x0018
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_SHIFT 3
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_2_5G 0x0018
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_1G 0x0010
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_100M 0x0008
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_10M 0x0000
-#define MDIO_SERDES_DIGITAL_MISC1 0x18
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_MASK 0xE000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_25M 0x0000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_100M 0x2000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_125M 0x4000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M 0x6000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_187_5M 0x8000
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL 0x0010
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK 0x000f
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_2_5G 0x0000
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_5G 0x0001
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_6G 0x0002
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_HIG 0x0003
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4 0x0004
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12G 0x0005
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12_5G 0x0006
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G 0x0007
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_15G 0x0008
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_16G 0x0009
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1 0x10
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE 0x0001
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_TBI_IF 0x0002
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN 0x0004
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT 0x0008
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET 0x0010
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE 0x0020
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2 0x11
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN 0x0001
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_AN_FST_TMR 0x0040
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1 0x14
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_DUPLEX 0x0004
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_MASK 0x0018
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_SHIFT 3
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_2_5G 0x0018
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_1G 0x0010
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_100M 0x0008
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_10M 0x0000
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS2 0x15
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED 0x0002
+#define MDIO_SERDES_DIGITAL_MISC1 0x18
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_MASK 0xE000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_25M 0x0000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_100M 0x2000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_125M 0x4000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M 0x6000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_187_5M 0x8000
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL 0x0010
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK 0x000f
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_2_5G 0x0000
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_5G 0x0001
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_6G 0x0002
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_HIG 0x0003
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4 0x0004
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12G 0x0005
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12_5G 0x0006
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G 0x0007
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_15G 0x0008
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_16G 0x0009
#define MDIO_REG_BANK_OVER_1G 0x8320
-#define MDIO_OVER_1G_DIGCTL_3_4 0x14
-#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_MASK 0xffe0
-#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_SHIFT 5
-#define MDIO_OVER_1G_UP1 0x19
-#define MDIO_OVER_1G_UP1_2_5G 0x0001
-#define MDIO_OVER_1G_UP1_5G 0x0002
-#define MDIO_OVER_1G_UP1_6G 0x0004
-#define MDIO_OVER_1G_UP1_10G 0x0010
-#define MDIO_OVER_1G_UP1_10GH 0x0008
-#define MDIO_OVER_1G_UP1_12G 0x0020
-#define MDIO_OVER_1G_UP1_12_5G 0x0040
-#define MDIO_OVER_1G_UP1_13G 0x0080
-#define MDIO_OVER_1G_UP1_15G 0x0100
-#define MDIO_OVER_1G_UP1_16G 0x0200
-#define MDIO_OVER_1G_UP2 0x1A
-#define MDIO_OVER_1G_UP2_IPREDRIVER_MASK 0x0007
-#define MDIO_OVER_1G_UP2_IDRIVER_MASK 0x0038
-#define MDIO_OVER_1G_UP2_PREEMPHASIS_MASK 0x03C0
-#define MDIO_OVER_1G_UP3 0x1B
-#define MDIO_OVER_1G_UP3_HIGIG2 0x0001
-#define MDIO_OVER_1G_LP_UP1 0x1C
-#define MDIO_OVER_1G_LP_UP2 0x1D
-#define MDIO_OVER_1G_LP_UP2_MR_ADV_OVER_1G_MASK 0x03ff
-#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK 0x0780
-#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT 7
-#define MDIO_OVER_1G_LP_UP3 0x1E
+#define MDIO_OVER_1G_DIGCTL_3_4 0x14
+#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_MASK 0xffe0
+#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_SHIFT 5
+#define MDIO_OVER_1G_UP1 0x19
+#define MDIO_OVER_1G_UP1_2_5G 0x0001
+#define MDIO_OVER_1G_UP1_5G 0x0002
+#define MDIO_OVER_1G_UP1_6G 0x0004
+#define MDIO_OVER_1G_UP1_10G 0x0010
+#define MDIO_OVER_1G_UP1_10GH 0x0008
+#define MDIO_OVER_1G_UP1_12G 0x0020
+#define MDIO_OVER_1G_UP1_12_5G 0x0040
+#define MDIO_OVER_1G_UP1_13G 0x0080
+#define MDIO_OVER_1G_UP1_15G 0x0100
+#define MDIO_OVER_1G_UP1_16G 0x0200
+#define MDIO_OVER_1G_UP2 0x1A
+#define MDIO_OVER_1G_UP2_IPREDRIVER_MASK 0x0007
+#define MDIO_OVER_1G_UP2_IDRIVER_MASK 0x0038
+#define MDIO_OVER_1G_UP2_PREEMPHASIS_MASK 0x03C0
+#define MDIO_OVER_1G_UP3 0x1B
+#define MDIO_OVER_1G_UP3_HIGIG2 0x0001
+#define MDIO_OVER_1G_LP_UP1 0x1C
+#define MDIO_OVER_1G_LP_UP2 0x1D
+#define MDIO_OVER_1G_LP_UP2_MR_ADV_OVER_1G_MASK 0x03ff
+#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK 0x0780
+#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT 7
+#define MDIO_OVER_1G_LP_UP3 0x1E
+
+#define MDIO_REG_BANK_REMOTE_PHY 0x8330
+#define MDIO_REMOTE_PHY_MISC_RX_STATUS 0x10
+#define MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG 0x0010
+#define MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG 0x0600
#define MDIO_REG_BANK_BAM_NEXT_PAGE 0x8350
-#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL 0x10
-#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE 0x0001
-#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN 0x0002
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL 0x10
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE 0x0001
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN 0x0002
+
+#define MDIO_REG_BANK_CL73_USERB0 0x8370
+#define MDIO_CL73_USERB0_CL73_UCTRL 0x10
+#define MDIO_CL73_USERB0_CL73_UCTRL_USTAT1_MUXSEL 0x0002
+#define MDIO_CL73_USERB0_CL73_USTAT1 0x11
+#define MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK 0x0100
+#define MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37 0x0400
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1 0x12
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN 0x8000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN 0x4000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN 0x2000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL3 0x14
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR 0x0001
+
+#define MDIO_REG_BANK_AER_BLOCK 0xFFD0
+#define MDIO_AER_BLOCK_AER_REG 0x1E
+
+#define MDIO_REG_BANK_COMBO_IEEE0 0xFFE0
+#define MDIO_COMBO_IEEE0_MII_CONTROL 0x10
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK 0x2040
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_10 0x0000
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100 0x2000
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000 0x0040
+#define MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX 0x0100
+#define MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN 0x0200
+#define MDIO_COMBO_IEEO_MII_CONTROL_AN_EN 0x1000
+#define MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK 0x4000
+#define MDIO_COMBO_IEEO_MII_CONTROL_RESET 0x8000
+#define MDIO_COMBO_IEEE0_MII_STATUS 0x11
+#define MDIO_COMBO_IEEE0_MII_STATUS_LINK_PASS 0x0004
+#define MDIO_COMBO_IEEE0_MII_STATUS_AUTONEG_COMPLETE 0x0020
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV 0x14
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX 0x0020
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_HALF_DUPLEX 0x0040
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE 0x0000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC 0x0080
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC 0x0100
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_NEXT_PAGE 0x8000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1 0x15
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_NEXT_PAGE 0x8000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_ACK 0x4000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_MASK 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_NONE 0x0000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_BOTH 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_HALF_DUP_CAP 0x0040
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_FULL_DUP_CAP 0x0020
+/*WhenthelinkpartnerisinSGMIImode(bit0=1),then
+bit15=link,bit12=duplex,bits11:10=speed,bit14=acknowledge.
+Theotherbitsarereservedandshouldbezero*/
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_SGMII_MODE 0x0001
+
+
+#define MDIO_PMA_DEVAD 0x1
+/*ieee*/
+#define MDIO_PMA_REG_CTRL 0x0
+#define MDIO_PMA_REG_STATUS 0x1
+#define MDIO_PMA_REG_10G_CTRL2 0x7
+#define MDIO_PMA_REG_RX_SD 0xa
+/*bcm*/
+#define MDIO_PMA_REG_BCM_CTRL 0x0096
+#define MDIO_PMA_REG_FEC_CTRL 0x00ab
+#define MDIO_PMA_REG_RX_ALARM_CTRL 0x9000
+#define MDIO_PMA_REG_LASI_CTRL 0x9002
+#define MDIO_PMA_REG_RX_ALARM 0x9003
+#define MDIO_PMA_REG_TX_ALARM 0x9004
+#define MDIO_PMA_REG_LASI_STATUS 0x9005
+#define MDIO_PMA_REG_PHY_IDENTIFIER 0xc800
+#define MDIO_PMA_REG_DIGITAL_CTRL 0xc808
+#define MDIO_PMA_REG_DIGITAL_STATUS 0xc809
+#define MDIO_PMA_REG_TX_POWER_DOWN 0xca02
+#define MDIO_PMA_REG_CMU_PLL_BYPASS 0xca09
+#define MDIO_PMA_REG_MISC_CTRL 0xca0a
+#define MDIO_PMA_REG_GEN_CTRL 0xca10
+#define MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP 0x0188
+#define MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET 0x018a
+#define MDIO_PMA_REG_M8051_MSGIN_REG 0xca12
+#define MDIO_PMA_REG_M8051_MSGOUT_REG 0xca13
+#define MDIO_PMA_REG_ROM_VER1 0xca19
+#define MDIO_PMA_REG_ROM_VER2 0xca1a
+#define MDIO_PMA_REG_EDC_FFE_MAIN 0xca1b
+#define MDIO_PMA_REG_PLL_BANDWIDTH 0xca1d
+#define MDIO_PMA_REG_PLL_CTRL 0xca1e
+#define MDIO_PMA_REG_MISC_CTRL0 0xca23
+#define MDIO_PMA_REG_LRM_MODE 0xca3f
+#define MDIO_PMA_REG_CDR_BANDWIDTH 0xca46
+#define MDIO_PMA_REG_MISC_CTRL1 0xca85
+
+#define MDIO_PMA_REG_SFP_TWO_WIRE_CTRL 0x8000
+#define MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK 0x000c
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE 0x0000
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE 0x0004
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IN_PROGRESS 0x0008
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_FAILED 0x000c
+#define MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT 0x8002
+#define MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR 0x8003
+#define MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF 0xc820
+#define MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK 0xff
+#define MDIO_PMA_REG_8726_TX_CTRL1 0xca01
+#define MDIO_PMA_REG_8726_TX_CTRL2 0xca05
+
+#define MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR 0x8005
+#define MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF 0x8007
+#define MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK 0xff
+#define MDIO_PMA_REG_8727_MISC_CTRL 0x8309
+#define MDIO_PMA_REG_8727_TX_CTRL1 0xca02
+#define MDIO_PMA_REG_8727_TX_CTRL2 0xca05
+#define MDIO_PMA_REG_8727_PCS_OPT_CTRL 0xc808
+#define MDIO_PMA_REG_8727_GPIO_CTRL 0xc80e
+
+#define MDIO_PMA_REG_8073_CHIP_REV 0xc801
+#define MDIO_PMA_REG_8073_SPEED_LINK_STATUS 0xc820
+#define MDIO_PMA_REG_8073_XAUI_WA 0xc841
+
+#define MDIO_PMA_REG_7101_RESET 0xc000
+#define MDIO_PMA_REG_7107_LED_CNTL 0xc007
+#define MDIO_PMA_REG_7101_VER1 0xc026
+#define MDIO_PMA_REG_7101_VER2 0xc027
+
+#define MDIO_PMA_REG_8481_PMD_SIGNAL 0xa811
+#define MDIO_PMA_REG_8481_LED1_MASK 0xa82c
+#define MDIO_PMA_REG_8481_LED2_MASK 0xa82f
+#define MDIO_PMA_REG_8481_LED3_MASK 0xa832
+#define MDIO_PMA_REG_8481_LED3_BLINK 0xa834
+#define MDIO_PMA_REG_8481_SIGNAL_MASK 0xa835
+#define MDIO_PMA_REG_8481_LINK_SIGNAL 0xa83b
+
+
+#define MDIO_WIS_DEVAD 0x2
+/*bcm*/
+#define MDIO_WIS_REG_LASI_CNTL 0x9002
+#define MDIO_WIS_REG_LASI_STATUS 0x9005
+
+#define MDIO_PCS_DEVAD 0x3
+#define MDIO_PCS_REG_STATUS 0x0020
+#define MDIO_PCS_REG_LASI_STATUS 0x9005
+#define MDIO_PCS_REG_7101_DSP_ACCESS 0xD000
+#define MDIO_PCS_REG_7101_SPI_MUX 0xD008
+#define MDIO_PCS_REG_7101_SPI_CTRL_ADDR 0xE12A
+#define MDIO_PCS_REG_7101_SPI_RESET_BIT (5)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR 0xE02A
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_WRITE_ENABLE_CMD (6)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_BULK_ERASE_CMD (0xC7)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_PAGE_PROGRAM_CMD (2)
+#define MDIO_PCS_REG_7101_SPI_BYTES_TO_TRANSFER_ADDR 0xE028
+
+
+#define MDIO_XS_DEVAD 0x4
+#define MDIO_XS_PLL_SEQUENCER 0x8000
+#define MDIO_XS_SFX7101_XGXS_TEST1 0xc00a
+
+#define MDIO_XS_8706_REG_BANK_RX0 0x80bc
+#define MDIO_XS_8706_REG_BANK_RX1 0x80cc
+#define MDIO_XS_8706_REG_BANK_RX2 0x80dc
+#define MDIO_XS_8706_REG_BANK_RX3 0x80ec
+#define MDIO_XS_8706_REG_BANK_RXA 0x80fc
+
+#define MDIO_AN_DEVAD 0x7
+/*ieee*/
+#define MDIO_AN_REG_CTRL 0x0000
+#define MDIO_AN_REG_STATUS 0x0001
+#define MDIO_AN_REG_STATUS_AN_COMPLETE 0x0020
+#define MDIO_AN_REG_ADV_PAUSE 0x0010
+#define MDIO_AN_REG_ADV_PAUSE_PAUSE 0x0400
+#define MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC 0x0800
+#define MDIO_AN_REG_ADV_PAUSE_BOTH 0x0C00
+#define MDIO_AN_REG_ADV_PAUSE_MASK 0x0C00
+#define MDIO_AN_REG_ADV 0x0011
+#define MDIO_AN_REG_ADV2 0x0012
+#define MDIO_AN_REG_LP_AUTO_NEG 0x0013
+#define MDIO_AN_REG_MASTER_STATUS 0x0021
+/*bcm*/
+#define MDIO_AN_REG_LINK_STATUS 0x8304
+#define MDIO_AN_REG_CL37_CL73 0x8370
+#define MDIO_AN_REG_CL37_AN 0xffe0
+#define MDIO_AN_REG_CL37_FC_LD 0xffe4
+#define MDIO_AN_REG_CL37_FC_LP 0xffe5
+
+#define MDIO_AN_REG_8073_2_5G 0x8329
+
+#define MDIO_AN_REG_8481_LEGACY_MII_CTRL 0xffe0
+#define MDIO_AN_REG_8481_LEGACY_AN_ADV 0xffe4
+#define MDIO_AN_REG_8481_1000T_CTRL 0xffe9
+#define MDIO_AN_REG_8481_EXPANSION_REG_RD_RW 0xfff5
+#define MDIO_AN_REG_8481_EXPANSION_REG_ACCESS 0xfff7
+#define MDIO_AN_REG_8481_LEGACY_SHADOW 0xfffc
+
+#define IGU_FUNC_BASE 0x0400
+
+#define IGU_ADDR_MSIX 0x0000
+#define IGU_ADDR_INT_ACK 0x0200
+#define IGU_ADDR_PROD_UPD 0x0201
+#define IGU_ADDR_ATTN_BITS_UPD 0x0202
+#define IGU_ADDR_ATTN_BITS_SET 0x0203
+#define IGU_ADDR_ATTN_BITS_CLR 0x0204
+#define IGU_ADDR_COALESCE_NOW 0x0205
+#define IGU_ADDR_SIMD_MASK 0x0206
+#define IGU_ADDR_SIMD_NOMASK 0x0207
+#define IGU_ADDR_MSI_CTL 0x0210
+#define IGU_ADDR_MSI_ADDR_LO 0x0211
+#define IGU_ADDR_MSI_ADDR_HI 0x0212
+#define IGU_ADDR_MSI_DATA 0x0213
+
+#define IGU_INT_ENABLE 0
+#define IGU_INT_DISABLE 1
+#define IGU_INT_NOP 2
+#define IGU_INT_NOP2 3
+
+#define COMMAND_REG_INT_ACK 0x0
+#define COMMAND_REG_PROD_UPD 0x4
+#define COMMAND_REG_ATTN_BITS_UPD 0x8
+#define COMMAND_REG_ATTN_BITS_SET 0xc
+#define COMMAND_REG_ATTN_BITS_CLR 0x10
+#define COMMAND_REG_COALESCE_NOW 0x14
+#define COMMAND_REG_SIMD_MASK 0x18
+#define COMMAND_REG_SIMD_NOMASK 0x1c
+
+
+#define IGU_MEM_BASE 0x0000
+
+#define IGU_MEM_MSIX_BASE 0x0000
+#define IGU_MEM_MSIX_UPPER 0x007f
+#define IGU_MEM_MSIX_RESERVED_UPPER 0x01ff
+
+#define IGU_MEM_PBA_MSIX_BASE 0x0200
+#define IGU_MEM_PBA_MSIX_UPPER 0x0200
+
+#define IGU_CMD_BACKWARD_COMP_PROD_UPD 0x0201
+#define IGU_MEM_PBA_MSIX_RESERVED_UPPER 0x03ff
+
+#define IGU_CMD_INT_ACK_BASE 0x0400
+#define IGU_CMD_INT_ACK_UPPER\
+ (IGU_CMD_INT_ACK_BASE + MAX_SB_PER_PORT * NUM_OF_PORTS_PER_PATH - 1)
+#define IGU_CMD_INT_ACK_RESERVED_UPPER 0x04ff
+
+#define IGU_CMD_E2_PROD_UPD_BASE 0x0500
+#define IGU_CMD_E2_PROD_UPD_UPPER\
+ (IGU_CMD_E2_PROD_UPD_BASE + MAX_SB_PER_PORT * NUM_OF_PORTS_PER_PATH - 1)
+#define IGU_CMD_E2_PROD_UPD_RESERVED_UPPER 0x059f
+
+#define IGU_CMD_ATTN_BIT_UPD_UPPER 0x05a0
+#define IGU_CMD_ATTN_BIT_SET_UPPER 0x05a1
+#define IGU_CMD_ATTN_BIT_CLR_UPPER 0x05a2
+
+#define IGU_REG_SISR_MDPC_WMASK_UPPER 0x05a3
+#define IGU_REG_SISR_MDPC_WMASK_LSB_UPPER 0x05a4
+#define IGU_REG_SISR_MDPC_WMASK_MSB_UPPER 0x05a5
+#define IGU_REG_SISR_MDPC_WOMASK_UPPER 0x05a6
+
+#define IGU_REG_RESERVED_UPPER 0x05ff
+
+
+#define CDU_REGION_NUMBER_XCM_AG 2
+#define CDU_REGION_NUMBER_UCM_AG 4
+
+
+/**
+ * String-to-compress [31:8] = CID (all 24 bits)
+ * String-to-compress [7:4] = Region
+ * String-to-compress [3:0] = Type
+ */
+#define CDU_VALID_DATA(_cid, _region, _type)\
+ (((_cid) << 8) | (((_region)&0xf)<<4) | (((_type)&0xf)))
+#define CDU_CRC8(_cid, _region, _type)\
+ (calc_crc8(CDU_VALID_DATA(_cid, _region, _type), 0xff))
+#define CDU_RSRVD_VALUE_TYPE_A(_cid, _region, _type)\
+ (0x80 | ((CDU_CRC8(_cid, _region, _type)) & 0x7f))
+#define CDU_RSRVD_VALUE_TYPE_B(_crc, _type)\
+ (0x80 | ((_type)&0xf << 3) | ((CDU_CRC8(_cid, _region, _type)) & 0x7))
+#define CDU_RSRVD_INVALIDATE_CONTEXT_VALUE(_val) ((_val) & ~0x80)
+
+/******************************************************************************
+ * Description:
+ * Calculates crc 8 on a word value: polynomial 0-1-2-8
+ * Code was translated from Verilog.
+ * Return:
+ *****************************************************************************/
+static inline u8 calc_crc8(u32 data, u8 crc)
+{
+ u8 D[32];
+ u8 NewCRC[8];
+ u8 C[8];
+ u8 crc_res;
+ u8 i;
-#define MDIO_REG_BANK_CL73_USERB0 0x8370
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1 0x12
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN 0x8000
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN 0x4000
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN 0x2000
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL3 0x14
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR 0x0001
+ /* split the data into 31 bits */
+ for (i = 0; i < 32; i++) {
+ D[i] = (u8)(data & 1);
+ data = data >> 1;
+ }
-#define MDIO_REG_BANK_AER_BLOCK 0xFFD0
-#define MDIO_AER_BLOCK_AER_REG 0x1E
+ /* split the crc into 8 bits */
+ for (i = 0; i < 8; i++) {
+ C[i] = crc & 1;
+ crc = crc >> 1;
+ }
-#define MDIO_REG_BANK_COMBO_IEEE0 0xFFE0
-#define MDIO_COMBO_IEEE0_MII_CONTROL 0x10
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK 0x2040
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_10 0x0000
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100 0x2000
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000 0x0040
-#define MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX 0x0100
-#define MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN 0x0200
-#define MDIO_COMBO_IEEO_MII_CONTROL_AN_EN 0x1000
-#define MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK 0x4000
-#define MDIO_COMBO_IEEO_MII_CONTROL_RESET 0x8000
-#define MDIO_COMBO_IEEE0_MII_STATUS 0x11
-#define MDIO_COMBO_IEEE0_MII_STATUS_LINK_PASS 0x0004
-#define MDIO_COMBO_IEEE0_MII_STATUS_AUTONEG_COMPLETE 0x0020
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV 0x14
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX 0x0020
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_HALF_DUPLEX 0x0040
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE 0x0000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC 0x0080
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC 0x0100
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_NEXT_PAGE 0x8000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1 0x15
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_NEXT_PAGE 0x8000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_ACK 0x4000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_MASK 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_NONE\
- 0x0000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_BOTH\
- 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_HALF_DUP_CAP 0x0040
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_FULL_DUP_CAP 0x0020
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_SGMII_MODE 0x0001
+ NewCRC[0] = D[31] ^ D[30] ^ D[28] ^ D[23] ^ D[21] ^ D[19] ^ D[18] ^
+ D[16] ^ D[14] ^ D[12] ^ D[8] ^ D[7] ^ D[6] ^ D[0] ^ C[4] ^
+ C[6] ^ C[7];
+ NewCRC[1] = D[30] ^ D[29] ^ D[28] ^ D[24] ^ D[23] ^ D[22] ^ D[21] ^
+ D[20] ^ D[18] ^ D[17] ^ D[16] ^ D[15] ^ D[14] ^ D[13] ^
+ D[12] ^ D[9] ^ D[6] ^ D[1] ^ D[0] ^ C[0] ^ C[4] ^ C[5] ^
+ C[6];
+ NewCRC[2] = D[29] ^ D[28] ^ D[25] ^ D[24] ^ D[22] ^ D[17] ^ D[15] ^
+ D[13] ^ D[12] ^ D[10] ^ D[8] ^ D[6] ^ D[2] ^ D[1] ^ D[0] ^
+ C[0] ^ C[1] ^ C[4] ^ C[5];
+ NewCRC[3] = D[30] ^ D[29] ^ D[26] ^ D[25] ^ D[23] ^ D[18] ^ D[16] ^
+ D[14] ^ D[13] ^ D[11] ^ D[9] ^ D[7] ^ D[3] ^ D[2] ^ D[1] ^
+ C[1] ^ C[2] ^ C[5] ^ C[6];
+ NewCRC[4] = D[31] ^ D[30] ^ D[27] ^ D[26] ^ D[24] ^ D[19] ^ D[17] ^
+ D[15] ^ D[14] ^ D[12] ^ D[10] ^ D[8] ^ D[4] ^ D[3] ^ D[2] ^
+ C[0] ^ C[2] ^ C[3] ^ C[6] ^ C[7];
+ NewCRC[5] = D[31] ^ D[28] ^ D[27] ^ D[25] ^ D[20] ^ D[18] ^ D[16] ^
+ D[15] ^ D[13] ^ D[11] ^ D[9] ^ D[5] ^ D[4] ^ D[3] ^ C[1] ^
+ C[3] ^ C[4] ^ C[7];
+ NewCRC[6] = D[29] ^ D[28] ^ D[26] ^ D[21] ^ D[19] ^ D[17] ^ D[16] ^
+ D[14] ^ D[12] ^ D[10] ^ D[6] ^ D[5] ^ D[4] ^ C[2] ^ C[4] ^
+ C[5];
+ NewCRC[7] = D[30] ^ D[29] ^ D[27] ^ D[22] ^ D[20] ^ D[18] ^ D[17] ^
+ D[15] ^ D[13] ^ D[11] ^ D[7] ^ D[6] ^ D[5] ^ C[3] ^ C[5] ^
+ C[6];
+ crc_res = 0;
+ for (i = 0; i < 8; i++)
+ crc_res |= (NewCRC[i] << i);
-#define EXT_PHY_OPT_PMA_PMD_DEVAD 0x1
-#define EXT_PHY_OPT_WIS_DEVAD 0x2
-#define EXT_PHY_OPT_PCS_DEVAD 0x3
-#define EXT_PHY_OPT_PHY_XS_DEVAD 0x4
-#define EXT_PHY_OPT_CNTL 0x0
-#define EXT_PHY_OPT_PMD_RX_SD 0xa
-#define EXT_PHY_OPT_PMD_MISC_CNTL 0xca0a
-#define EXT_PHY_OPT_PHY_IDENTIFIER 0xc800
-#define EXT_PHY_OPT_PMD_DIGITAL_CNT 0xc808
-#define EXT_PHY_OPT_PMD_DIGITAL_SATUS 0xc809
-#define EXT_PHY_OPT_CMU_PLL_BYPASS 0xca09
-#define EXT_PHY_OPT_LASI_CNTL 0x9002
-#define EXT_PHY_OPT_RX_ALARM 0x9003
-#define EXT_PHY_OPT_LASI_STATUS 0x9005
-#define EXT_PHY_OPT_PCS_STATUS 0x0020
-#define EXT_PHY_OPT_XGXS_LANE_STATUS 0x0018
+ return crc_res;
+}
-#define EXT_PHY_KR_PMA_PMD_DEVAD 0x1
-#define EXT_PHY_KR_PCS_DEVAD 0x3
-#define EXT_PHY_KR_AUTO_NEG_DEVAD 0x7
-#define EXT_PHY_KR_CTRL 0x0000
-#define EXT_PHY_KR_CTRL2 0x0007
-#define EXT_PHY_KR_PCS_STATUS 0x0020
-#define EXT_PHY_KR_PMD_CTRL 0x0096
-#define EXT_PHY_KR_LASI_CNTL 0x9002
-#define EXT_PHY_KR_LASI_STATUS 0x9005
-#define EXT_PHY_KR_MISC_CTRL1 0xca85
-#define EXT_PHY_KR_GEN_CTRL 0xca10
-#define EXT_PHY_KR_ROM_CODE 0xca19
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff