config MACB
tristate "Atmel MACB support"
- depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
config KS8842
tristate "Micrel KSZ8842"
+ depends on HAS_IOMEM
help
- This platform driver is for Micrel KSZ8842 chip.
+ This platform driver is for Micrel KSZ8842 / KS8842
+ 2-port ethernet switch chip (managed, VLAN, QoS).
+
+config KS8851
+ tristate "Micrel KS8851 SPI"
+ depends on SPI
+ select MII
+ select CRC32
+ help
+ SPI driver for Micrel KS8851 SPI attached network chip.
+
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ help
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
config VIA_RHINE
tristate "VIA Rhine support"
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
select PHYLIB
help
TI AR7 CPMAC Ethernet support
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
- If compiled as module, it will be called 'fec_mpc52xx.ko'.
+ If compiled as module, it will be called fec_mpc52xx.
config FEC_MPC52xx_MDIO
bool "MPC52xx FEC MDIO bus driver"
(Motorola? industry standard).
If your board uses an external PHY connected to FEC, enable this.
If not sure, enable.
- If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.
+ If compiled as module, it will be called fec_mpc52xx_phy.
config NE_H8300
tristate "NE2000 compatible support for H8/300"
To compile this driver as a module, choose M here. The module
will be called atl2.
+config XILINX_EMACLITE
+ tristate "Xilinx 10/100 Ethernet Lite support"
+ depends on PPC32 || MICROBLAZE
+ help
+ This driver supports the 10/100 Ethernet Lite from Xilinx.
+
+config BCM63XX_ENET
+ tristate "Broadcom 63xx internal mac support"
+ depends on BCM63XX
+ select MII
+ select PHYLIB
+ help
+ This driver supports the ethernet MACs in the Broadcom 63xx
+ MIPS chipset family (BCM63XX).
+
source "drivers/net/fs_enet/Kconfig"
endif # NET_ETHERNET
depends on SKGE && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/skge/ethX displays the state of the internal
+ The file /sys/kernel/debug/skge/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
depends on SKY2 && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/sky2/ethX displays the state of the internal
+ The file /sys/kernel/debug/sky2/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
To compile this driver as a module, choose M here: the module
will be called bnx2. This is recommended.
+config CNIC
+ tristate "Broadcom CNIC support"
+ depends on PCI
+ select BNX2
+ select UIO
+ help
+ This driver supports offload features of Broadcom NetXtremeII
+ gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cnic. This is recommended.
+
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
-config UGETH_MAGIC_PACKET
- bool "Magic Packet detection support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
To compile this driver as a module, choose M here. The module
will be called jme.
+config S6GMAC
+ tristate "S6105 GMAC ethernet support"
+ depends on XTENSA_VARIANT_S6000
+ select PHYLIB
+ help
+ This driver supports the on chip ethernet device on the
+ S6105 xtensa processor.
+
+ To compile this driver as a module, choose M here. The module
+ will be called s6gmac.
+
endif # NETDEV_1000
#
select FW_LOADER
select ZLIB_INFLATE
select LIBCRC32C
+ select MDIO
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
source "drivers/atm/Kconfig"
+source "drivers/ieee802154/Kconfig"
+
source "drivers/s390/net/Kconfig"
config XEN_NETDEV_FRONTEND
This is the virtual network driver for virtio. It can be used with
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
+config VMXNET3
+ tristate "VMware VMXNET3 ethernet driver"
+ depends on PCI && X86
+ help
+ This driver supports VMware's vmxnet3 virtual ethernet NIC.
+ To compile this driver as a module, choose M here: the
+ module will be called vmxnet3.
+
endif # NETDEVICES
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff