config MACB
tristate "Atmel MACB support"
- depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
config ETHOC
tristate "OpenCores 10/100 Mbps Ethernet MAC support"
- depends on NET_ETHERNET && HAS_IOMEM
+ depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
select MII
select PHYLIB
select CRC32
config SMSC911X
tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
- depends on ARM || SUPERH || BLACKFIN
+ depends on ARM || SUPERH || BLACKFIN || MIPS
select CRC32
select MII
select PHYLIB
Please email feedback to <torben.mathiasen@compaq.com>.
+config KS8842
+ tristate "Micrel KSZ8842"
+ depends on HAS_IOMEM
+ help
+ This platform driver is for Micrel KSZ8842 / KS8842
+ 2-port ethernet switch chip (managed, VLAN, QoS).
+
+config KS8851
+ tristate "Micrel KS8851 SPI"
+ depends on SPI
+ select MII
+ select CRC32
+ help
+ SPI driver for Micrel KS8851 SPI attached network chip.
+
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ select MII
+ help
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
+
config VIA_RHINE
tristate "VIA Rhine support"
depends on NET_PCI && PCI
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
select PHYLIB
help
TI AR7 CPMAC Ethernet support
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
- If compiled as module, it will be called 'fec_mpc52xx.ko'.
+ If compiled as module, it will be called fec_mpc52xx.
config FEC_MPC52xx_MDIO
bool "MPC52xx FEC MDIO bus driver"
(Motorola? industry standard).
If your board uses an external PHY connected to FEC, enable this.
If not sure, enable.
- If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.
+ If compiled as module, it will be called fec_mpc52xx_phy.
config NE_H8300
tristate "NE2000 compatible support for H8/300"
To compile this driver as a module, choose M here. The module
will be called atl2.
+config XILINX_EMACLITE
+ tristate "Xilinx 10/100 Ethernet Lite support"
+ depends on PPC32 || MICROBLAZE
+ help
+ This driver supports the 10/100 Ethernet Lite from Xilinx.
+
+config BCM63XX_ENET
+ tristate "Broadcom 63xx internal mac support"
+ depends on BCM63XX
+ select MII
+ select PHYLIB
+ help
+ This driver supports the ethernet MACs in the Broadcom 63xx
+ MIPS chipset family (BCM63XX).
+
source "drivers/net/fs_enet/Kconfig"
endif # NET_ETHERNET
depends on SKGE && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/skge/ethX displays the state of the internal
+ The file /sys/kernel/debug/skge/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
depends on SKY2 && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/sky2/ethX displays the state of the internal
+ The file /sys/kernel/debug/sky2/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
To compile this driver as a module, choose M here: the module
will be called bnx2. This is recommended.
+config CNIC
+ tristate "Broadcom CNIC support"
+ depends on PCI
+ select BNX2
+ select UIO
+ help
+ This driver supports offload features of Broadcom NetXtremeII
+ gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cnic. This is recommended.
+
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
config GELIC_WIRELESS
bool "PS3 Wireless support"
+ depends on WLAN
depends on GELIC_NET
select WIRELESS_EXT
help
config GELIC_WIRELESS_OLD_PSK_INTERFACE
bool "PS3 Wireless private PSK interface (OBSOLETE)"
depends on GELIC_WIRELESS
+ select WEXT_PRIV
help
This option retains the obsolete private interface to pass
the PSK from user space programs to the driver. The PSK
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
-config UGETH_MAGIC_PACKET
- bool "Magic Packet detection support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
To compile this driver as a module, choose M here. The module
will be called jme.
+config S6GMAC
+ tristate "S6105 GMAC ethernet support"
+ depends on XTENSA_VARIANT_S6000
+ select PHYLIB
+ help
+ This driver supports the on chip ethernet device on the
+ S6105 xtensa processor.
+
+ To compile this driver as a module, choose M here. The module
+ will be called s6gmac.
+
+source "drivers/net/stmmac/Kconfig"
+
endif # NETDEV_1000
#
config NIU
tristate "Sun Neptune 10Gbit Ethernet support"
depends on PCI
+ select CRC32
help
This enables support for cards based upon Sun's
Neptune chipset.
select FW_LOADER
select ZLIB_INFLATE
select LIBCRC32C
+ select MDIO
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
source "drivers/atm/Kconfig"
+source "drivers/ieee802154/Kconfig"
+
source "drivers/s390/net/Kconfig"
config XEN_NETDEV_FRONTEND
This is the virtual network driver for virtio. It can be used with
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
+config VMXNET3
+ tristate "VMware VMXNET3 ethernet driver"
+ depends on PCI && INET
+ help
+ This driver supports VMware's vmxnet3 virtual ethernet NIC.
+ To compile this driver as a module, choose M here: the
+ module will be called vmxnet3.
+
endif # NETDEVICES
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff